PH1800
Operator’s Guide
PowerHub 1800
Download from Www.Somanuals.com. All Manuals Search And Download.
PowerHub 1800
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
About Xantrex
Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls
with products from 50 watt mobile units to 2.5 MW utility-scale systems for wind, solar, batteries,
fuel cells, microturbines, and backup power applications in both grid-connected and stand-alone
systems. Xantrex products include inverters, battery chargers, programmable power supplies, and
variable speed drives that convert, supply, control, clean, and distribute electrical power.
Trademarks
PowerHub 1800 is a trademark of Xantrex International. Xantrex is a registered trademark of
Xantrex International.
Other trademarks, registered trademarks, and product names are the property of their respective
owners and are used herein for identification purposes only.
Notice of Copyright
PowerHub 1800 Operator’s Guide © January 2007 Xantrex International. All rights reserved.
Exclusion for Documentation
UNLESS SPECIFICALLY AGREED TO IN WRITING, XANTREX TECHNOLOGY INC. (“XANTREX”)
(A) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY
TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.
(B) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR EXPENSES,
WHETHER SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT
OF THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT
THE USER’S RISK; AND
(C) REMINDS YOU THAT IF THIS MANUAL IS IN ANY LANGUAGE OTHER THAN ENGLISH, ALTHOUGH
STEPS HAVE BEEN TAKEN TO MAINTAIN THE ACCURACY OF THE TRANSLATION, THE ACCURACY
CANNOT BE GUARANTEED. APPROVED XANTREX CONTENT IS CONTAINED WITH THE ENGLISH
LANGUAGE VERSION WHICH IS POSTED AT WWW.XANTREX.COM.
Date and Revision
January 2007 Revision C
Part Number
975-0288-01-01
Product Number
PH1800-GFP
Contact Information
Telephone: 1 800 670 0707 (toll free North America)
1 360 925 5097 (direct)
Fax:
1 800 994 7828 (toll free North America)
1 360 925 5143 (direct)
Email:
Web:
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
Purpose
The purpose of this Operator’s Guide is to provide procedures for
operating the PowerHub 1800.
Scope
The Guide provides safety guidelines, detailed planning and setup
information, and procedures for operating the inverter. It does not provide
operational or troubleshooting information. It does not provide details
about particular brands of batteries. Consult individual battery
manufacturers for this information.
Audience
The PowerHub is an entry-level inverter system. This Guide is intended
for anyone who needs to operate the PowerHub 1800. Permanent
installations should be done by certified technicians or electricians.
Installers should have adequate knowledge of national and local electric
code to ensure code-compliance by inspection from the local electric
authority.
Organization
This Guide is organized into three chapters and one appendix.
Chapter 1 describes the operational features and functions of the
PowerHub 1800. This section details how the unit functions as an
inverter, provides information on the control panel, and describes
operating limits for inverter operation.
Chapter 2 contains information on operating the PowerHub 1800.
Chapter 3 explains how to troubleshoot the PowerHub 1800 and describes
the error codes that may be displayed on the LCD.
Appendix A provides electrical and physical specifications for the
PowerHub 1800.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
Conventions Used
The following conventions are used in this guide.
WARNING
Warnings identify conditions or practices that could result in personal injury or
loss of life
CAUTION
Cautions identify conditions or practices that could result in damage to the unit or
other equipment.
Important: These notes describe things which are important for you to know,
but not as serious as a caution or warning.
Abbreviations and Acronyms
Abbreviation or Acronym Definition
A
Amps
AC
DC
ft-lbs
kW
LED
Nm
PV
Alternating Current
Direct Current
Foot-pounds (a measure of torque)
Kilowatts (1000 watts)
Light Emitting Diode
Newton-meters (a measurement of torque)
Photovoltaic
RE
Renewable Energy
Volts AC
Vac
Vdc
W
Volts DC
Watts
Related Information
You can find more information about this product by seeing the
PowerHub 1800 Installation Guide (part number 975-0289-01-01). You
can find more information about Xantrex Technology Inc. as well as its
products and services at www.xantrex.com.
iv
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
WARNING
This chapter contains important safety and operating instructions. Read and keep
this Operator’s Guide for future reference.
WARNING: Limitations on use
The PowerHub 1800 is not intended for use in connection with life support
systems or other medical equipment or devices.
WARNING
To avoid the risk of carbon monoxide poisoning, generators are not to be used
indoors. When generators are used outdoors there must be sufficient circulation
to vent the carbon monoxide.
1. Before installing and using the PowerHub 1800, read all instructions
and cautionary markings on the PowerHub, the batteries, and in both
the Installation Guide and the Operator’s Guide.
2. The PowerHub is intended for indoor use only. Do not expose the
PowerHub to rain, snow, or spray. To reduce risk of fire hazard, do
not cover or obstruct the ventilation openings. Do not install the
PowerHub in a zero-clearance compartment. Overheating may result.
3. The PowerHub may connect to as many as three sources of DC Power
and one source of AC Power. To reduce the risk of electrical shock,
disconnect all sources of AC and DC power from the PowerHub
before attempting any maintenance or cleaning or working on any
circuits connected to the PowerHub. Turning off controls will not
eliminate this risk.
4. Use only attachments that are intended for use with this product.
Doing otherwise may result in a risk of fire, electric shock, or injury
to persons.
5. To avoid a risk of fire and electric shock, make sure that all of the
installation wiring is in good condition and that wire is not
undersized. Do not operate the PowerHub with damaged or
substandard wiring.
6. Do not operate the PowerHub if it has received a sharp blow, been
dropped, or otherwise damaged in any way. If the PowerHub is
damaged, see the “Return Procedure” on page WA–3.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
7. Do not disassemble the PowerHub, except where noted to wire it for a
permanent installation or to install batteries. The PowerHub 1800
contains no user-serviceable parts. See “Warranty” on page WA–1 for
instructions on obtaining service. Attempting to service the
PowerHub yourself may result in a risk of electrical shock or fire and
will void your warranty. Internal capacitors remain charged after all
power is disconnected.
8. The PowerHub must be provided with an equipment-grounding
conductor. Grounding and all other wiring must comply with national
and local codes and regulations.
9. The PowerHub 1800 is not intended for use as an uninterruptible
power supply (UPS).
No!
No!
No!
No!
Figure i Basic Safety
vi
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
Precautions When Working With Batteries
WARNING: Fire or Explosion Hazard
1. Use only SEALED batteries with the PowerHub 1800.
2. Follow all instructions published by the battery manufacturer.
3. Working in the vicinity of batteries may be dangerous. Unsealed
batteries can generate explosive gases during normal operation.
Therefore, you must read this guide and follow the instructions
exactly before installing or using the PowerHub.
4. This equipment contains components which tend to produce arcs or
sparks. To prevent fire or explosion, do not install the PowerHub in
locations that require ignition-protected equipment. This includes any
space containing gasoline-powered machinery, fuel tanks, as well as
joints, fittings, or other connections between components of the fuel
system.
5. To reduce the risk of battery explosion, follow these instructions and
those published by the battery manufacturer.
6. Make sure that nothing is blocking the air vents on the back of the
enclosure.
7. Never smoke or allow a spark or flame near the batteries.
8. Use caution to reduce the risk of dropping a metal tool on the
batteries. It could spark or short circuit the battery or other electrical
parts and could cause an explosion.
9. Remove all personal metal items, like rings, bracelets, and watches
when working with batteries. Batteries can produce a short circuit
current high enough to weld metal, causing a severe burn.
10. Have someone within range of your voice or close enough to come to
your aid when you work near a battery.
11. Wear complete eye protection and clothing protection. Avoid
touching your eyes while working near batteries.
12. Have plenty of fresh water and soap nearby in case battery acid
contacts skin, clothing, or eyes.
975-0288-01-01
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
13. If battery acid contacts skin or clothing, wash immediately with soap
and water. If acid enters your eye, immediately flood it with running
cold water for at least twenty minutes and get medical attention
immediately.
Precautions for Using Rechargeable Appliances
CAUTION: Equipment Damage
This equipment produces a modified sine wave output. Equipment damage may
occur if the rechargeable appliance is not designed to use modified sine wave
output. If you are unsure about using your rechargeable appliance with the
modified sine wave, contact the equipment manufacturer.
Most rechargeable battery-operated equipment uses a separate charger or
transformer that is plugged into an AC receptacle and produces a low
voltage charging output.
Some chargers for small rechargeable batteries can be damaged if
connected to the PowerHub. Do not use the following with the PowerHub:
•
Small battery-operated appliances like flashlights, razors, and night
lights that can be plugged directly into an AC receptacle to recharge.
•
Some chargers for battery packs used in power hand tools. These
affected chargers display a warning label stating that dangerous
voltages are present at the battery terminals.
FCC/ICES 003 Information to the User
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
viii
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Power Down Procedure
The power down procedure will be depend on how the unit has been
installed. If using the AC cord to plug the PowerHub directly into a
generator, this is referred to as “softwiring” or “plug-and-go”. If installing
in a permanent location, that is referred to as “hardwiring”.
If softwired......
To Power Down the PowerHub 1800:
Press ON/OFF Switch to turn
OFF Inverter/Charger
2
1
Disconnect Loads
Disconnect the Battery Box(es)
from the Inverter
4
Disconnect the PowerHub
from the generator and
turn the generator OFF.
3
OFF
Figure ii Power Down Procedure for Softwired Installations
975-0288-01-01
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
If hardwired......
To Power Down the PowerHub 1800:
WARNING: Shock Hazard
If no DC Disconnect is used, then the DC input generators (solar or wind) will
have to be physically disconnected to ensure power is OFF.
2
1
Disconnect Loads connected to
Disconnect any loads directly
connected to the front panel of
the PowerHub
the PowerHub through AC
Distribution Panel (Sub-panel)
by opening the Inverter Output
Circuit Breaker.
4
Press ON/OFF
Switch to turn OFF
Inverter/Charger
3
Disconnect the
DC Input.(s)
Disconnect the Battery Box(es)
from the Inverter
6
Disconnect the Utility
5
power by opening the AC
input circuit breaker in the
main panel.
Figure iii Power Down Procedure for Hardwired Installations
x
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Important Safety Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -v
Precautions When Working With Batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - - -vii
Precautions for Using Rechargeable Appliances - - - - - - - - - - - - - - - - - - - - - - - - - viii
FCC/ICES 003 Information to the User - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - viii
Power Down Procedure - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ix
1 Introduction
Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–2
Principles of Inverter Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–2
Basic Functions of the PowerHub 1800 - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–3
Inverter Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–4
Battery Charger Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–5
2 Operation
Inverter Control Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–2
User Controls and Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–3
Operating Mode LEDs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–4
Status LEDs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–4
Input LEDs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–4
Output LEDs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–5
Selecting Charger Settings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–5
Basic Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–6
Power On and Off - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–6
Changing the Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–7
Changing Charging Settings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–9
Connecting AC Loads - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–10
Typical Loads that might be used with the PowerHub 1800 - - - - - - - - - - - - - 2–12
Loads That Might Not Work Well With the PowerHub 1800 - - - - - - - - - - - - - 2–12
Loads that should NOT be used with the PowerHub 1800 - - - - - - - - - - - - - - - 2–12
975-0288-01-01
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
3 Troubleshooting
How to Troubleshoot the PowerHub 1800 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–2
Error Codes- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–3
If Utility Power is NOT Available- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–5
If Utility Power is Available- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–7
Possible Problem Loads - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–8
Rechargeable Devices - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–9
Ground Fault Protection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–10
Replacing the Ground Fault Protection Fuse - - - - - - - - - - - - - - - - - - - - - - - - 3–10
A Specifications
Electrical Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–2
Physical Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–3
Battery Charger Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–3
Charging Profiles - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–5
40-amp Charging Profile - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–5
10-amp Charging Profile - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–6
0-amp Charging Profile - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–6
xii
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Figures
Figure i
Figure ii
Figure iii
Basic Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - vi
Power Down Procedure for Softwired Installations- - - - - - - - - - - - - - - - - - ix
Power Down Procedure for Hardwired Installations - - - - - - - - - - - - - - - - - x
Figure 1-1 Principles of Inverter Operation- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–2
Figure 1-2 PowerHub 1800 Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–4
Figure 1-3 Three-Stage Charging Process- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–6
Figure 2-1 The PowerHub 1800 Inverter Control Panel - - - - - - - - - - - - - - - - - - - - 2–2
Figure 2-2 Basic Startup Screens- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–6
Figure 2-3 Input Displays - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–7
Figure 2-4 Output Displays - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–8
Figure 2-5 Input Displays - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–9
Figure 2-6 Connecting AC Loads - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–11
Figure 2-7 Loads That Should Never Be Used With the PowerHub 1800- - - - - - - - - 2–12
Figure 3-1 Replacing Ground Fault Protection Fuse - - - - - - - - - - - - - - - - - - - - - - - 3–11
Figure A-1 Three-Stage Charging Process- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–4
975-0288-01-01
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
Table 3-1
Table 3-2
Table 3-3
Error Codes for Troubleshooting the PowerHub 1800 - - - - - - - - - - - - - - 3–3
Possible Problems if Utility Power is Not Available - - - - - - - - - - - - - - - 3–5
Possible Problems if Utility Power is Available - - - - - - - - - - - - - - - - - - 3–7
Table A-1 Electrical Specifications for the Inverter - - - - - - - - - - - - - - - - - - - - - - - A–2
Table A-2 Electrical Specifications for the Battery Box - - - - - - - - - - - - - - - - - - - - A–2
Table A-3 Physical Specifications of the Inverter - - - - - - - - - - - - - - - - - - - - - - - - A–3
Table A-4 Physical Specifications of the Battery Box - - - - - - - - - - - - - - - - - - - - - A–3
Table A-5 40-amp Charging Profile - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–5
Table A-6 10-amp Charging Profile - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–6
975-0288-01-01
i
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Introduction
Chapter 1 describes the operational features and functions of the
PowerHub 1800. This section details how the unit functions as an
inverter, provides information on the control panel, and describes
operating limits for inverter operation.
For this topic...
See...
“Principles of Inverter Operation”
“Basic Functions of the PowerHub 1800”
“Inverter Features”
page 1–2
page 1–3
page 1–3
page 1–5
“Battery Charger Features”
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Introduction
Thank you for your purchase of this Xantrex Home Power System. The
modified sine wave AC output from the inverter ensures AC loads
operating from the unit perform efficiently and correctly.
To get the most out of your PowerHub 1800, carefully read and follow the
instructions in this guide. Pay special attention to the Important Safety
Instructions and to the CAUTION and WARNING statements found
throughout this manual and on the product. Please retain all packaging.
Should you have any questions before, during, or after the installation,
please contact Xantrex Customer Support. Please see “How do you get
service?” on page WA–1 in this Guide for contact information.
Principles of Inverter Operation
The PowerHub 1800 converts power from the batteries in two stages. The
first stage is a DC-to-DC converter, used to raise the low voltage DC
input to high voltage DC. The second stage is the actual inverter stage,
taking the high voltage DC and converting it to a modified sine wave AC
output.
The DC-to-DC converter stage uses modern high frequency power
conversion technology that eliminates the bulky, low frequency
(50/60 Hz) based transformers found in inverters using older technology.
The inverter stage uses advanced power semiconductors that provide
excellent overload capabilities.
AC
INPUT
H
G
N
+
L
↓
N
+
–
High Voltage
DC
DC to DC
Converter
DC to AC
Converter
AC
OUTPUT
Transfer Relay
N
G
H
N
↓
L
Modified
Sine Wave
AC
–
Figure 1-1 Principles of Inverter Operation
Output
Waveform
The AC output waveform of the PowerHub 1800 is a “modified sine
wave” .
1–2
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Basic Functions of the PowerHub 1800
Bypass
When AC power is available from a generator or utility grid, the
Function
PowerHub will function as an automatic backup power unit. It will sit in
Bypass mode and will pass the power through to support the loads and/or
the battery charger. When the AC input fails, the PowerHub’s Automatic
Transfer Relay de-energizes and will switch the unit to Inverter Mode
within 40 milliseconds.
Once AC input is restored, after a 20-second delay the relay energizes and
qualifies the AC input and the load is automatically reconnected to the
primary AC source.
WARNING: Shock Hazard
If any AC power is available to the PowerHub 1800, the unit will pass through
that power to any loads connected to it whether the unit is turned ON or OFF.
Power will be available at the four outlets on the front of the unit as well as at any
outlets hardwired to the unit through the AC distribution panel. There is a blue
LED above the 15 A supplemental protector on the front of the inverter panel that
will illuminate if AC power is available at the AC outlets.
To completely disable this feature, the PowerHub must be completely
disconnected from all input sources. Turning off the display will not eliminate
this risk.
Inverter
Function
When no AC power is available from a generator or utility grid, the
inverter draws power from the battery bank and delivers a modified-sine
wave AC output voltage. This output voltage can be accessed by using the
four outlets on the front of the unit or by hardwiring the unit to the AC
Distribution Panel which provides AC power to AC outlets at the site.
Charger
Function
The PowerHub 1800 uses any single source of AC power such as a
generator or utility grid to keep the batteries charged and ready for use.
The PowerHub 1800 can also use renewable energy sources to keep the
batteries charged.
Important: Additional hardware, such as charge controllers, may be required
for installations using renewable energy sources. Installations using renewable
energy input must be hardwired into the installation for code-compliance.
Operational
Voltage Range
As long as the battery voltage is between 11.0 Vdc to 15.0 Vdc, the
inverter will continue to deliver AC power to the loads connected to it.
When the battery voltage falls below 11.0 Vdc or rises above 15.0 Vdc,
the PowerHub 1800 High or Low Battery Protection will engage and shut
the inverter off, stopping all output voltage to the loads.
975-0288-01-01
1–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Inverter Features
User Features
The inverter consists of the following user features.
•
The Inverter Control Panel provides a user interface for monitoring
power levels, battery levels, and controlling the inverter functions and
displays.
•
•
•
Four 120 Vac outlets on the front panel provide up to 1440 W
(continuous) output power.
One 15 A supplemental protector provides over-load protection to the
four AC outlets on the front panel.
One AC Indicator LED. This LED will illuminate whenever AC
power is available, whether the unit is ON or OFF. See page 2–3 for
additional information about this LED.
•
One PVGFP, ground fault protection fuse for safety when using solar
and wind renewable energy inputs.
WARNING: Shock Hazard
The 15 A circuit breaker on the front panel is only connected to the four outlets
on the front of the panel and only disconnects power to these outlets when
activated. It does not disable output through the output terminals used for
hardwiring. Therefore, power can still be available to loads connected through a
hardwired installation.
Inverter Control
Panel
ON/OFF Power
Button
AC Outlets (x4)
AC Indicator LED
15 A Supplemental
Protector
Figure 1-2 PowerHub 1800 Features
1–4
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Battery Charger Features
Charging
Settings
The Battery Charger in the PowerHub 1800 has three pre-set charging
profiles.
•
40 A Profile (Default Setting). With the 40-amp Charging Profile, the
maximum bypass power for AC output to loads is approximately
600 W (4 A) with a 15 A input breaker. Use this mode to minimize
battery charging time.
•
10 A Profile. With the 10-amp Charging Profile, the maximum
bypass power for AC output to loads is approximately 1400 W (12 A)
with a 15 A input breaker. Use this mode when other DC charging
sources are available, or if there is a high demand on AC output with
battery charging a low priority.
•
0 A Profile. When Charger Setting 0 A is selected, the Battery
Charger is disabled and will not charge the batteries. Use this mode if
other DC charging sources are available or if it is necessary to
temporarily disconnect the AC charging system.
See “Battery Charger Specifications” on page A–3 for details on the
specific profile parameters.
Charging
Process
The Battery Charger uses a three-stage charging process to maintain the
battery (or batteries) in operational condition. This process is illustrated in
Figure 1-3, “Three-Stage Charging Process” on page 1–6.
Bulk Stage
The bulk stage will start upon connection of AC and with the unit turned
on. The constant current mode is limited to 40 A or 10 A depending on
setting. The voltage setpoint for this stage is 14.2 Vdc. The Charger will
transition to the Absorption Stage upon reaching the bulk voltage
setpoint.
Absorption
Stage
In the Absorption Stage, the constant voltage mode is limited to 14.2 Vdc.
The current will drop as the batteries charge. Upon dropping to 4 A, the
unit will transition to the Float charge. This stage will not exceed 4 hours
maximum.
Float Stage
In the Float stage, the constant voltage mode limited to 13.7 Vdc. An
8-hour timer is started at this point.
If, during the 8-hour timer, the current rises to 6 A, the unit transitions
back to the Bulk Stage and starts over.
If the unit stays at 4A or less for the entire 8 hour timer, it will transition
to Standby Mode.
975-0288-01-01
1–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Standby Mode
In the Standby Mode, the Charger is OFF but monitors the battery
voltage. If battery voltage drops below 12.5 Vdc, the unit will start a new
Bulk stage.
Bulk
Stage
Absorption
Stage
Standby
(Stop Mode)
Float Stage
13.7 Vdc
If the voltage drops to 12.5 Vdc
while in Standby, the Charger
will start a new Bulk Stage.
14.2 Vdc
12.5 Vdc
12.5 Vdc
Voltage
Current
40 A or
10 A
Maximum
Charge
Amps
4 A
Setting
Time
8 hours
4 hours
(Maximum)
40 A or
10 A
If the current rises to 6A
during the Float period, the
Charger will start the whole
cycle back at the Bulk Stage.
Current
Maximum
Charge
Amps
6 A
Setting
4 A
Time
8 hours
4 hours
(Maximum)
Figure 1-3 Three-Stage Charging Process
The PowerHub 1800 will reset to the default setting of 40 A whenever
one of the following occurs.
1. The unit is turned OFF by the ON/OFF Button.
2. All DC input sources (solar panels or wind generators) are removed
and utility AC is not available.
1–6
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Operation
Chapter 2 contains information on operating the PowerHub 1800.
For this topic...
See...
“Inverter Control Panel”
“User Controls and Display”
“Selecting Charger Settings”
“Basic Operation”
page 2–2
page 2–3
page 2–5
page 2–6
page 2–6
page 2–7
page 2–9
page 2–10
page 2–12
“Power On and Off”
“Changing the Display”
“Changing Charging Settings”
“Connecting AC Loads”
“Typical Loads that might be used with the
PowerHub 1800”
“Loads That Might Not Work Well With the
PowerHub 1800”
page 2–12
page 2–12
“Loads that should NOT be used with the
PowerHub 1800”
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Inverter Control Panel
The Inverter Control Panel has nine LEDs; six Status LEDs (three for
input/charge levels and three for output power levels), two Mode
Indication LEDs, one AC Indicator LED. Two push buttons provide
ON/OFF control and Display Select features. An LED Display
communicates input and output power levels, battery voltage, and error
codes.
Input LEDs
Output LEDs
LED Display
8.8.8.8.
On/Off Power
Inverter Mode
Indicator LED
Button*
Bypass Mode
Indicator LED
Select Button
Important:
AC Indicator
LED
*The On/Off Power Button only activates or
deactivates power to the Inverter/charger and display.
If the PowerHub is connected to any AC power
source it will pass that power through to the outlets
on the front panel and to the output terminals.
Figure 2-1 The PowerHub 1800 Inverter Control Panel
2–2
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Inverter Control Panel
User Controls and Display
The following provides a detailed description of the user controls and
LED display function. For operating instructions, see “Basic Operation”
on page 2–6.
On/Off Power
Button (Green)
To turn the power ON or OFF, press and hold the green ON/OFF Power
Button for approximately 1 second.
WARNING: Shock Hazard
The ON/OFF Button controls the output of the inverter/charger and the displays
only. It does not control or turn off the AC output in Bypass Mode. Therefore, if
any power is available to the unit, the unit will function in Bypass Mode and
power will be available at all outlets or output terminals even if the PowerHub is
turned OFF. The blue AC Indicator LED between the top two AC outlets on the
front panel will illuminate if AC power is available at any of the outlets.
LED Display
The LED Display consists of a 4-digit numerical display (e.g., 8.8.8.8.).
(Note: 1.0 kW = 1000 watts)
•
Negative numbers (e.g., ꢀ1.00) represent Output Power in kilowatts
(kW). This number represents the power being removed from the
batteries to power the loads. This can only occur when displaying Net
Power using the Select button while in Inverter Mode.
•
•
•
Positive numbers (e.g., 0.56) represent Input Power in kilowatts.
This number represents the power being used to charge the batteries
and power the loads.
Battery Level information is displayed in volts DC. The Battery
Level LED will illuminate when this value is being displayed.
(e.g., 12.8)
AC charger information is displayed in kilowatts. This value indicates
the amount of power available to charge the batteries. The AC LED
will illuminate when this value is being displayed. This value
indicates the amount of power being used to charge the batteries.
The Display by default will display the Net Power value.
Fault Condition
Display
If a fault occurs, the error code will immediately be displayed as a
flashing, 3-digit alpha/numeric code (e.g., E01). An audible beep will
sound to draw attention to the fault condition.
For a complete list of Error Codes, see Chapter 3, “How to Troubleshoot
the PowerHub 1800”).
AC Indicator
LED
The AC Indicator LED indicates that AC power is available at all outputs.
If AC power is available, this LED will illuminate whether or not the
PowerHub 1800 inverter is turned on.
975-0288-01-01
2–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operating Mode LEDs
Bypass LED
When AC power source is available, the PowerHub 1800 will pass the
power through to the loads and will also keep the battery bank charged
and usable. The Bypass LED will illuminate when the unit is in this mode.
WARNING: Shock Hazard
The ON/OFF Button controls the output of the inverter only. It does not control
or turn off the AC output in Bypass Mode. Therefore, if any power is available to
the unit, the unit will function in Bypass Mode and power will be available at all
outlet or output terminals even if the PowerHub is turned OFF. The blue AC
Indicator LED between the top two AC outlets on the front panel will illuminate
if power is available at the front four outlets.
On initial power up or if transferring from Inverter Mode back to Bypass
Mode, the PowerHub takes approximately 20 seconds to identify if an AC
source is available and stable. If the AC source is within the acceptable
voltage range, the PowerHub will automatically enter Bypass Mode.
During this time, the Bypass Mode LED will flash and power will still be
provided by the inverter. When the AC source has been qualified, the
Bypass Mode LED will stop flashing and illuminates solid and the loads
will be powered by the AC source.
Inverter LED
If the PowerHub is on with AC present and the AC source fails, the
PowerHub 1800 automatically switches to Inverter Mode within 40
milliseconds. When in Inverter mode, the inverter is using the power
stored in the battery bank to provide power to the loads and the Inverter
LED will illuminate.
Status LEDs
Input LEDs
Select Button
(Red)
Pressing the red Select Button cycles the output on the display through the
available Input/Output power levels.
If the Select button is not pushed within 10 seconds, the display will
automatically return to the Net Power value.
Wind LED
When the Select Button is pressed until the Wind LED is illuminated, the
Wind Input wattage levels are displayed in kilowatts. These values are the
inputs on the 80 A DC input terminals.
2–4
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Inverter Control Panel
Solar LED
AC LED
When the Select Button is pressed again within 10 seconds and the Solar
LED is illuminated, the Solar Input wattage levels are displayed in
kilowatts. These values are the inputs on the 32 A DC input terminals.
If the unit is in Bypass Mode, when the Select Button is pressed again
within 10 seconds and the AC LED is illuminated, the battery charger
power level is displayed in kilowatts.
Output LEDs
Net Power LED
By default the Net Power LED represents the difference between the
input and the output power levels. This value is shown on startup and will
return to this display if the Select button is not pressed for 10 seconds.
When using the Select Button to cycle through the displays and the Net
Power LED is illuminated, the power level displayed will depend on
whether the unit is in Bypass Mode or Inverter Mode.
In Bypass Mode, the value displayed represents the power, in kilowatts,
that is available to charge the battery and to power the loads. This will be
a positive number.
In Inverter Mode, this value displayed represents the total amount of
power in kilowatts that is being drawn from the battery bank (negative
numbers) or is available to charge the battery by the DC source while the
inverter is running (positive numbers).
Battery LED
Output LED
When the Select Button is pressed again within 10 seconds and the
Battery Level LED is illuminated, the battery voltage level is displayed in
DC volts. It will also show “FUL” when the battery is charged through the
AC charger and reaches float and standby mode.
When the Select Button is pressed again within 10 seconds and the
Inverter LED is illuminated, the Inverter Output power is displayed in
kilowatts. This only displays if the unit is in Invert Mode.
Selecting Charger Settings
Charger
Settings
Pressing and holding the Select Button for 3-5 seconds will change the
display to show the AC charger current setting and the AC LED will
flash.
See “Battery Charger Features” on page 1–5 for more information
regarding setting parameters. See “Changing Charging Settings” on
page 2–9 for instructions on changing this setting.
975-0288-01-01
2–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Basic Operation
The following figures show what the Inverter Control Panel will look like
when the user controls are used.
Important: The values shown in the displays of the following illustrations are
examples only. Actual values may vary based on what is connected to the unit.
Power On and Off
To turn the power to the
PowerHub ON or OFF:
◆ Press and hold the green
ON/OFF Power Button for
approximately 1 second.
If any input power is available, the Inverter Control
panel will display as shown below. The value shown
on the display defaults to indicate Net Power.
Net Power = Input - Output
If no input power is available and no loads
are connected to the unit, the Inverter
Control panel will display as shown below.
Default Screen Example
Default Screen Example
Example indicates 540 watts.
Figure 2-2 Basic Startup Screens
2–6
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Changing the Display
Press the red Select button to cycle the display through the input and
output power values.
Wind input will be displayed.
(This display indicates 1 kw or 1000 watts)
Press once.
Solar input will be displayed.
(This display indicates 0.36 Kw or 360 watts)
Press again within 10 seconds.
Charger input will be displayed.
(This display indicates 0.48 kW or 480 watts)
This screen only displays in Bypass Mode.
Press again within 10 seconds.
Continued in Figure 2-4...
Figure 2-3 Input Displays
975-0288-01-01
2–7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued from Figure 2-3...
Net Power will be displayed.
Press again within 10 seconds.
Battery Voltage will be displayed.
(This displays 12.8 Vdc)
Press again within 10 seconds.
Inverter Output will be displayed.
(This displays 1.44 Kw or 1440 watts)
Displays in Inverter Mode only.
Press again within 10 seconds.
Figure 2-4 Output Displays
2–8
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Changing Charging Settings
Default Setting
The PowerHub 1800 is set at the factory to default to the 40 A Charging
Profile. In the event that one of the other profiles are required, follow the
instructions below to change the setting.
Setting the
Selection
To set the selection to the desired profile, stop pressing the Select Button
when the desired profile is displayed. The unit will set the profile shown
in the display, then will return to the default screen within 10 seconds.
Returns to
Default
The charging setting will revert to the 40 A default setting whenever the
ON/OFF Button is pressed or all DC input sources are removed and utility
AC is not available.
Press and hold for approximately
3-5 seconds.
The AC LED will start to flash.
Display shows default
charge setting (40A)
The Charge Setting changes
to the 10 A profile.
Press again within 10 seconds.
The Charge Setting changes to the
0 A profile. This profile completely
turns off the charging feature.
Press again within 10 seconds.
Figure 2-5 Input Displays
975-0288-01-01
2–9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
If the AC Charger goes into an over temperature shutdown condition, the
40 A setting will automatically change to 10 A to reduce the charging
current. The charging current will change back to 40 A when the unit
cools to an acceptable temperature.
Important:
When Charger is set to 40 A or 10 A, Battery Level will flash between battery
voltage and 'FUL' when it reaches Float Mode or Off Mode. Otherwise it shows
measured battery voltage.
When AC Charger is set to 0 A, Battery Level shows measured battery voltage.
Connecting AC Loads
CAUTION: Equipment Damage
Never insert the AC input cord into the AC outlets on the front of the PowerHub
1800 when the batteries are connected. This can damage the unit and will void
the warranty.
Continuous AC loads of 1440 watts (12 A) can be connected and run
from the PowerHub 1800 through the four AC outlets on the front panel.
Important: Know your loads. Use the formula below to help determine the
watts of the load if only amp ratings are provided with the appliance.
Volts x Amps = Watts
Maximum watts available for continuous use on the PowerHub 1800 = 1440 W
Maximum amperage available for AC loads is 12 A.
120 V x 12 A = 1440 W
In case of an
Overload
Exceeding 1800 watts will cause the unit to display an overload error
code and the unit will shut down.
Shutdown....
In the event of an overload shutdown, remove the loads that are connected
to the PowerHub and turn the power OFF, then back ON.
If the unit is hardwired to a sub-panel, it will also be necessary to check
the circuit breaker in the sub-panel.
In the event of an overload shutdown, if charge settings had been changed
to 10 A or 0 A prior to the shutdown, the charging parameters will have to
be reset. Otherwise, the unit will default back to the 40 A profile.
2–10
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting AC Loads
ON/OFF
Power Button
120 Vac
Power Outlets
(x4)
AC Indicator LED
Supplemental
Protector
Important: The combination of
loads can not exceed 1440 W.
NO!
NO!
Figure 2-6 Connecting AC Loads
WARNING: Shock Hazard
Do not insert objects not intended for use with an electric appliance into the AC
power outlets on the PowerHub (e.g., fingers, tools, jewelry). Not intended for
use by small children,
975-0288-01-01
2–11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Typical Loads that might be used with the PowerHub 1800
The following types of appliances can be used with the PowerHub 1800
providing.
❐ Sump pumps
❐ Microwaves
❐ Refrigerators
❐ Freezers
❐ Lighting
❐ Television or Audio Equipment
❐ Most power tools
Loads That Might Not Work Well With the PowerHub 1800
The following types of appliances might not work as expected with the
PowerHub 1800. See “Possible Problem Loads” on page 3–8 for
additional information.
❐ Some pellet stoves that have an auger for pellet feeding
❐ Some electronic furnace controls
❐ Some rechargeable devices
❐ Variable speed fans or lights with dimmer switches
Loads that should NOT be used with the PowerHub 1800
The PowerHub 1800 is not intended for use in connection with life support
systems or other medical equipment or devices.
Figure 2-7 Loads That Should Never Be Used With the PowerHub 1800
2–12
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Troubleshooting
Chapter 3 explains how to troubleshoot the PowerHub 1800 and
describes the error codes that may be displayed on the LCD.
For this topic...
See...
“How to Troubleshoot the PowerHub 1800”
“Error Codes”
page 3–2
page 3–3
page 3–5
page 3–7
page 3–8
“If Utility Power is NOT Available”
“If Utility Power is Available”
“Possible Problem Loads”
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
How to Troubleshoot the PowerHub 1800
Important: If the unit is not performing as expected, BEFORE returning the
unit to the retailer, please review this information carefully.
The following information is provided to assist in the troubleshooting of
the PowerHub 1800. Please review this information carefully.
Check First....
Check the following tables for information specific to your unit.
Table 3-1 provides information on the Error Codes that may be seen on
the Display. Table 3-2 describes possible issues that may arise when
utility power is NOT available. Table 3-3 describes possible issues that
may arise when utility power is available.
Check Next....
Finally....
Asked Questions) for your product. Many additional questions are
addressed at this website.
If the FAQs don’t address the problem you’re experiencing, then see
“Warranty” on page WA–1 for contact information for Xantrex Customer
Service. Contact a Xantrex Customer Support representative for
assistance.
3–2
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Codes
Error Codes
The following error codes may be displayed on the LED display if the
described fault conditions occur.
Table 3-1 Error Codes for Troubleshooting the PowerHub 1800
Error Code Description
Displayed of Error
Description of Condition
Resolution
E01
DC Input
Under Voltage
Shutdown
Unit shuts down.
The unit will automatically
reset once the fault condition is
removed.
If this condition is not corrected
and the unit powers down
completely, it will be necessary
to press the ON/OFF Button to
turn the unit ON again.
The input voltage has dropped to below
the operation voltage limit of 11.0 to
10.5 V.
An alarm continues to beep once every
second until input/output voltage drops to
10.3 V.
The alarm will continue to beep once
every 30 seconds until battery voltage
reaches 10.0 V. If the battery reaches
10.0 V, the display turns OFF and the unit
powers down completely.
E02
DC Input
Over Voltage
Shutdown
Unit shuts down.
The unit will automatically
reset once the fault condition is
removed.
An input voltage is greater than 15 V.
The alarm will continue to beep once
every second.
E03
E04
AC Output
Overload
Shutdown
Unit shuts down.
Remove excess AC loads.
Reset of unit is required.
To reset the unit, turn it OFF
and back ON.
An AC load applied to the system in
inverter mode is above operation limit.
System Over
Temperature
Shutdown
Unit shuts down.
Reduce loads or reduce ambient
temperature around the
PowerHub.
The unit will automatically
reset once the unit cools down
and reaches a safe operating
temperature.
System internal temperature is above
operation limit.
The alarm will continue to beep once
every second.
E05
DC Input
System is still operating but input voltage Unit continues to run.
Under Voltage has dropped too close to the shutdown
If the warning is ignored, the
unit will eventually goes to the
E01 fault condition.
Alarm
limit (11.0 to 10.5 Vdc).
Alarm will beep once every two seconds
until the warning condition is removed.
975-0288-01-01
3–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Table 3-1 Error Codes for Troubleshooting the PowerHub 1800
Error Code Description
Displayed of Error
Description of Condition
Resolution
E06
E07
E09
AC Output
Overload
Warning
System is still operating but AC load
applied to the system in inverter mode is If the warning is ignored, the
close to shutdown limit.
Unit continues to run.
unit will eventually go to the
E03 fault condition.
Alarm will beep once every two seconds
until the warning condition is removed.
System Over
Temperature
Warning
System is still operating but system
internal temperature is close to shutdown If the warning is ignored, unit
limit.
Unit continues to run.
will eventually go to the E04
fault condition.
Alarm will beep once every two seconds
until the warning condition is removed.
Ground Fault Unit shuts down.
Fuse Open
Warning
Turn the unit off. Check all DC
Input connections (PV, wind
etc.) and repair any faults or
damage. Replace the ground
fault fuse (see page 3–10) and
restart the unit
A ground fault has been detection.
3–4
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
If Utility Power is NOT Available
If Utility Power is NOT Available
The following fault conditions may arise when utility power is not
available.
Table 3-2 Possible Problems if Utility Power is Not Available
Problem
Probable Cause
Solution
Low output voltage.
(96 Vac to 104 Vac)
Voltmeter used cannot accurately Use a true RMS voltmeter.
read the RMS voltage of a
modified sine wave.
Display is OFF, AC is not The unit is OFF.
available on both
Turn the unit ON.
hardwired and units
AC sockets.
The inverter has no output.
•Check battery box connection.
•Check battery box fuses.
•Check wind or solar connections.
The unit might have been
•Check battery box fuses (all 10 of them)
connected with reverse DC input and check battery polarity.
polarity.
•Correct the cabling if connected
improperly.
•Replace the fuses in the battery box.
If the unit still does not start, it may be
damaged. Damage caused by reverse
polarity is not covered by the warranty.
AC is available but alarm
beeps.
Low Voltage Warning
(error code E05)
Charge battery immediately or unit will
be under voltage shutdown shortly.
Load applied to unit is close to overload
shutdown, reduce the load immediately or
overload or over temp may occur shortly.
Over Load Warning
(error code E06)
Check unit ventilation and reduce the load
applied to the unit or unit will run into
over temperature shutdown shortly.
Over Temperature Warning
(error code E07)
Display is ON, AC is
available on hardwire but
not on unit AC socket
15 A supplementary protector
has tripped.
Press reset button on the front panel to
reset the protector.
975-0288-01-01
3–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Table 3-2 Possible Problems if Utility Power is Not Available
Problem
Probable Cause
Solution
Display is ON, AC is not
available on both
hardwired and unit
AC socket.
Low input voltage
(error code E01)
Recharge the battery; check the
connections and cable.
High input voltage
(error code E02)
Make sure the unit is connected to a 12 V
battery. Check battery is not overcharged.
Unit is overload protected
(error code E03)
Reduce the amount of loads connected to
the unit or the start up surge on the load
exceed surge limit of the unit.
Unit is thermal protected
(error code E04)
Allow the unit to cool off. Reduce the
load if continuous operation is required.
Improve ventilation. Make sure the
inverter's ventilation openings are not
obstructed.
Reduce the ambient temperature.
Unit is ground fault protected
(error code E09)
Turn the unit off. Check all DC Input
connections (PV, wind etc.) and repair
any faults or damage. Replace the ground
fault fuse (see page 3–10) and restart the
unit
Digital display or LED is
flickering especially in a
dark environment.
Display is normal
N/A
Inadequate run time.
Internal battery is not fully
charged.
Charge the internal battery by leaving the
charger backup power system plugged
into a wall outlet at least 20 hours.
Internal battery has aged past its Replace the internal battery. The internal
warranted shelf life, the available battery also ages prematurely if the
run time decreases.
system is installed in a hot environment.
Products connected to unit Products connected to backup
Your application is not compatible with
backup power system modified sine wave
output.
malfunction or overheat.
power system do not accept
modified sine wave form.
See “Rechargeable Devices” on page 3–9.
3–6
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
If Utility Power is Available
If Utility Power is Available
The following fault conditions may arise when utility power is available.
Table 3-3 Possible Problems if Utility Power is Available
Problem
Probable Cause
Solution
Display is OFF, AC is
available on both hardwire
and unit AC socket
Inverter is turned OFF.
AC output is always available when
AC input is available. Under this
condition, the inverter will not back
up the power when utility power is
OFF.
Display is OFF, AC is not Main AC Panel or AC generator
Check utility or generator output
available on both hardwire input is beyond the operating range of voltage.
and unit AC socket
the unit (103 to 132 Vac).
Display is ON, AC is not
The 15A input circuit breaker on the Reset the 15 A input circuit breaker.
available on both hardwire Main AC Panel or AC generator is
and unit AC socket
tripped or turned OFF.
Reset the 15A supplemental protector
near the four AC outlets on the front
panel and reset the 15A circuit
The 15 A circuit breaker on AC
Distribution Panel and 15 A
supplementary protector near the four breaker on the AC Distribution Panel
AC outlets on the front panel have
tripped.
Display is ON, AC is
available on hardwire
output but not on unit
AC socket
15 A supplementary protector on the Press the reset button to reset the
front panel has tripped.
circuit breaker.
Bypass LED is flashing
During the first 20 seconds of transfer None.
from inverter to Bypass Mode, the
inverter continuous to run and the
Bypass LED flashes. This provides
time for the utility to get steady
before it switches over. During the 20
seconds delay time, the display
feature is frozen.
975-0288-01-01
3–7
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Possible Problem Loads
The inverter can drive most loads, however, there are special conditions
that can cause a load to behave differently than expected. The following
describes some of the common problems encountered when using an
inverter.
WARNING: Fire Hazard
Transformerless Battery Chargers are not to be used with any model of the
PowerHub 1800 family. Connecting a transformerless battery charger could
result in a overheating condition and possibly a fire.
Ceiling Fans
Most large diameter, slow turning fans run correctly, but generate more
noise than when connected to utility power. High speed fans tend to
operate normally.
Cell Phones
Clocks
Some cellular telephones experience interference in the form of a clicking
sound.
The inverter keeps the frequency accurate to within a few seconds a day;
however, external loads in the system may alter the inverter’s output
waveform causing clocks to run at different speeds. There may be periods
where clocks keep time and then mysteriously do not.
Dimmer
Switches
Most dimmer switches lose their ability to dim the lights when used with
an inverter and operate only in the fully ON or OFF position. Newer,
microprocessor controlled dimmers tend to work better in inverter
applications.
Heavy Loads
If the battery bank cannot deliver the necessary amperage to drive a heavy
load, the inverter will shut OFF. The battery voltage will then slowly rise
back above the low voltage threshold causing the inverter to resume
operation. As soon as the heavy load draws the batteries down, the cycle
will continue unless the load is reduced or an additional source of power
is added.
Microwave
Ovens
Microwave ovens are sensitive to peak output voltages. The higher the
voltage, the faster they cook. Since the inverter’s peak output voltage is
dependent upon battery voltage and load size, the microwave’s cook time
may need to be increased.
Printers
Most inkjet type printers work well in inverter applications. Laser
printers, however, require high current for their fusing circuit and are not
recommended for use with an inverter.
3–8
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Possible Problem Loads
Rechargeable Devices
CAUTION: Equipment Damage
This equipment produces a modified sine wave output. Equipment damage may
occur if the rechargeable appliance is not designed to use modified sine wave
output. If you are unsure about using your rechargeable appliance with the
modified sine wave, contact the equipment manufacturer.
When first using a rechargeable device, monitor its temperature for
10 minutes to ensure it does not become abnormally hot. Excessive heat
will indicate that it is incompatible with the inverter.
Most rechargeable battery-operated equipment uses a separate charger or
transformer that is plugged into an AC receptacle and produces a low
voltage charging output.
Some chargers for small rechargeable batteries can be damaged if
connected to the PowerHub. Do not use the following with the
PowerHub:
•
Small battery-operated appliances like flashlights, razors, and night
lights that can be plugged directly into an AC receptacle to recharge.
•
Some chargers for battery packs used in power hand tools. These
affected chargers display a warning label stating that dangerous
voltages are present at the battery terminals.
975-0288-01-01
3–9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Ground Fault Protection
WARNING: Shock hazard
Troubleshooting a grounding fault should be performed by qualified personnel,
such as a certified electrician or technician.
Ground fault protection is required when using either solar or wind
renewable energy input. Figure 3-1 shows the location of the ground fault
protection terminals and replaceable fuse.
When a grounding fault is detected, the ground fault protection fuse will
blow. The system must be shut down completely, the fault corrected, the
fuse replaced (see “Replacing the Ground Fault Protection Fuse”) and
then the system restarted.
Replacing the Ground Fault Protection Fuse
WARNING: Energy and fire hazard
For continued protection against risk of fire, replace the ground fault protection
fuse only with the same type and ratings of fuse.
WARNING: Shock hazard
After disconnection both AC and DC power for the the system, wait five minutes
before attempting any maintenance or cleaning or working on any circuits
connected to the inverter. Internal capacitors remain charged for five minutes
after disconnecting all sources of power.
The ground fault protection fuse will blow when severe leakage occurs
between the PV array and earth ground, or when the system has been
installed with faulty DC wiring. Before replacing the fuse, it is important
to have qualified service personnel, such as a certified electrician or
technician, to determine the cause of the ground fault.
To replace the ground fault protection fuse:
1. Remove the five Phillips screws on the top of the inverter and lift off
the panel to expose the terminals, as shown in Figure 3-1.
2. Locate the PV ground fault protection fuse.
3. Using a slot blade screwdriver, remove the blown fuse and replace it
with a new Littelfuse 5mm×20mm fuse rated 1A 250 Vac slow blow
(or equivalent).
3–10
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Ground Fault Protection
4. Replace the panel on the top of the inverter and tighten all five screws
securely.
BEFORE REMOVING INVERTER COVER:
Check to ensure the AC Indicator LED is NOT
illuminated and that there are absolutely no
sources of power connected to the PowerHub.
Remove the 5 #6-32
Phillips screws on
the top of the
inverter. Lift off the
panel to expose the
terminals.
PV Ground Fault
Protection Fuse
AC Indicator LED
Figure 3-1 Replacing Ground Fault Protection Fuse
975-0288-01-01
3–11
Download from Www.Somanuals.com. All Manuals Search And Download.
3–12
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Specifications
Appendix A provides electrical and physical specifications for the
PowerHub 1800.
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Electrical Specifications
Table A-1 Electrical Specifications for the Inverter
Parameter
PowerHub 1800 Inverter
1800 W (15A) (5 minutes maximum)
1440 W (12 A)
2880 W (24 A)
10.5 to 15.0 Vdc
60 Hz
Maximum Output Power
Continuous Output Power
Surge Rating
Input Voltage Range
Input Frequency Range
Peak Efficiency
88%
System Shutdown Mode
(Display On)
< 12 W
Idle Mode
<1.5 W
Output Frequency
60 Hz / ±1 Hz
Output Waveform (resistive load) Modified sine wave (>30% THD)
Output Voltage (at no load)
Low Battery Cutout
High Battery Cutout
Transfer Relay Rating
Transfer Time AC to Inverter
AC Qualification Time
Protection
110 to 125 Vac
10.5 Vdc with < 240 W load and 11.0 V with > 240 W load
15.0 Vdc
20 A
< 40 ms
~ 20 seconds
•
•
Five 20 A/32 Vdc fuses protecting the 80A/1000 W DC input
terminal.
Two 20 A/32 Vdc fuses protecting 32A/ 400 W DC input
terminal.
•
•
One 15 Aac supplemental protector.
One 1 A/250 Vac fuse for system ground fault protection.
Table A-2 Electrical Specifications for the Battery Box
1
Parameter
Battery Box
Protection
Ten 20 A/32 Vdc Fuses for short circuit and reverse polarity
conditions.
1.Stand-alone battery box Xantrex Part Number: PH1800-BBX
A–2
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Physical Specifications
Physical Specifications
Table A-3 Physical Specifications of the Inverter
Parameter
PowerHub 1800
Dimensions (H x W x L)
14.75" × 8.0" × 16.0"
(37.5 cm × 20 cm × 41 cm)
Weight
28.6 lb (13.0 kg)
Operating Temperature
Storage Temperature
0 °C (32 °F) to 40 °C (104 °F)
-30 °C (-22 °F) to 70 °C (158 °F)
Table A-4 Physical Specifications of the Battery Box
1
Parameter
Battery Box
Dimensions (H x W x L)
14.0" × 13.875" × 20.5"
(35.6 cm × 35.2 cm × 52.7 cm)
Weight
29 lb (13.2 kg)
Operating Temperature
Storage Temperature
0 °C (32 °F) to 40 °C (104 °F)
-30 °C (-22 °F) to 70 °C (158 °F)
1.Stand-alone battery box Xantrex Part Number: PH1800-BBX
Battery Charger Specifications
Charging
Process
The Battery Charger uses a three-stage charging process to maintain the
battery (or batteries) in operational condition. This process is illustrated in
Figure A-1, “Three-Stage Charging Process” on page A–4.
Bulk Stage
The bulk stage will start upon connection of AC and with the unit turned
on. The constant current mode is limited to 40 A or 10 A depending on
setting. The voltage setpoint for this stage is 14.2 Vdc. The Charger will
transition to the Absorption Stage upon reaching the bulk voltage
setpoint.
Absorption
Stage
In the Absorption Stage, the constant voltage mode is limited to 14.2 Vdc.
The current will drop as batteries voltage rises. Upon dropping to 4 A, the
unit will transition to the Float charge. This stage will not exceed 4 hours
maximum.
975-0288-01-01
A–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Float Stage
In the Float stage, the constant voltage mode limited to 13.7 Vdc. An 8-
hour timer is started at this point.
If, during the 8-hour timer, the current rises to 6 A, the unit transitions
back to the Bulk Stage and starts over.
If the unit stays at 4A or less for the 8 hour timer, it will transition to
Standby Mode.
Standby Mode
In the Standby Mode, the Charger is OFF but monitors the battery
voltage. If battery voltage drops below 12.5 Vdc, the unit will start a new
Bulk stage.
Bulk
Stage
Absorption
Stage
Standby
(Stop Mode)
Float Stage
13.7 Vdc
If the voltage drops to 12.5 Vdc
while in Standby, the Charger
will start a new Bulk Stage.
14.2 Vdc
12.5 Vdc
12.5 Vdc
Voltage
Current
40 A or
10 A
Maximum
Charge
Amps
4 A
Setting
Time
8 hours
4 hours
(Maximum)
40 A or
10 A
If the current rises to 6A
during the Float period, the
Charger will start the whole
cycle back at the Bulk Stage.
Current
Maximum
Charge
Amps
6 A
Setting
4 A
Time
8 hours
4 hours
(Maximum)
Figure A-1 Three-Stage Charging Process
A–4
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Charger Specifications
Charging Profiles
40-amp Charging Profile
Table A-5 provides the specific charging parameters for the 40 Charging
Profile.
Table A-5 40-amp Charging Profile
Parameter Name
Charger Setting
Maximum Bypass Current
Bulk Mode
Default Value
40 A
500 W (4 A)
40 A
Absorption Mode
Float Mode
14.2 Vdc (4 hours maximum)
13.7 Vdc (8 hours)
Switches from Absorption to Float 4 A
Mode
Switches from Float Mode back to 6 A
Bulk Mode within the 8-hour limit,
if the Float current increases to
6 A.
Standby Mode (Off Mode)
Estimated charging time
12.5 Vdc
8 hours based on a single battery box with
two 100 Ah, 12 Vdc batteries and no
other DC charging sources
975-0288-01-01
A–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
10-amp Charging Profile
Table A-6 provides the specific charging parameters for the 10 Charging
Profile.
Table A-6 10-amp Charging Profile
Parameter Name
Charger Setting
Maximum Bypass Current
Bulk Mode
Default Value
10 A
1200 W (10 A)
10 A
Absorption Mode
Float Mode
14.2 Vdc (4 hours maximum)
13.7 Vdc (8 hours)
Switches from Absorption to 4 A
Float Mode
Switches from Float Mode
back to Bulk Mode within the
8-hour limit, if the Float
current increases to 6 A.
6 A
Standby Mode (Off Mode)
Estimated charging time
12.5 Vdc
32 hours based on a single battery box with
two 100 Ah, 12 Vdc batteries and no other DC
charging sources
0-amp Charging Profile
When Charger Setting 0 A is selected, the Battery Charger is disabled and
will not charge the batteries. Use this mode if other DC charging sources
are available or if it is necessary to temporarily disconnect the AC
charging system.
A–6
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
G
AC LED 2–5
AC Loads 2–10
appliances
ground fault protection 3–10
H
battery-operated viii, 3–9
Heavy Loads 3–8
B
I
batteries
Information about Your System form WA–5
inverter
purchase date WA–5
serial number WA–5
Inverter LED 2–4
first aid when working with vii
precautions when working with vii
rechargeable viii, 3–9
battery chargers
for rechargeable batteries viii, 3–9
Battery LED 2–5
Bypass LED 2–4
L
LED Display 2–3
C
Ceiling Fans 3–8
Cell Phones 3–8
Changing Charging Settings 2–9
Clocks 3–8
M
Microwave Ovens 3–8
N
Customer Service
preparing to call WA–5
Net Power LED 2–5
D
O
Dimmer Switches 3–8
On/Off Power Button 2–3
Operating Mode LEDs 2–4
E
P
Error Codes 3–3
peak output voltage 3–8
Power On and Off 2–6
power tools, battery-operated viii, 3–9
Printers 3–8
Problem Loads 3–8
proof of purchase WA–5
purchase date WA–5
F
Fault Condition Display 2–3
FCC information to the user viii
first aid viii
975-0288-01-01
IX-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
R
Rechargeable Devices 3–9
S
safety instructions vii
Select Button 2–4
serial number WA–5
Solar LED 2–5
W
warranty
out of warranty service WA–4
terms and conditions WA–1
Wind LED 2–4
X
Xantrex
web site iv
IX–2
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Return Information
Warranty
What does this warranty cover? This Limited Warranty is provided by Xantrex Technology Inc.
("Xantrex") and covers defects in workmanship and materials in your PowerHub 1800. This warranty
period lasts for one year from the date of purchase at the point of sale to you, the original end user
customer. You will be required to demonstrate proof of purchase to make warranty claims.
This Limited Warranty is transferable to subsequent owners but only for the unexpired portion of the
Warranty Period. Subsequent owners are also required to provide original proof of purchase to make a
warranty claim.
What will Xantrex do? Xantrex will, at its option, repair or replace the defective product free of
charge, provided that you notify Xantrex of the product defect within the Warranty Period, and provided
that Xantrex through inspection establishes the existence of such a defect and that it is covered by this
Limited Warranty.
Xantrex will, at its option, use new and/or reconditioned parts in performing warranty repair and
building replacement products. Xantrex reserves the right to use parts or products of original or
improved design in the repair or replacement. If Xantrex repairs or replaces a product, its warranty
continues for the remaining portion of the original Warranty Period or 90 days from the date of the
return shipment to the customer, whichever is greater. All replaced products and all parts removed from
repaired products become the property of Xantrex.
Xantrex covers both parts and labor necessary to repair the product, and return shipment to the customer
via a Xantrex-selected non-expedited surface freight within the contiguous United States and Canada.
Alaska and Hawaii are excluded. Contact Xantrex Customer Service for details on freight policy for
return shipments outside of the contiguous United States and Canada.
How do you get service? If your product requires troubleshooting or warranty service, contact your
merchant. If you are unable to contact your merchant, or the merchant is unable to provide service,
contact Xantrex directly at:
Telephone: 1 800 670 0707 (toll free North America) Xantrex Customer Support
1 360 925 5097 (direct)
Fax:
1 800 994 7828 (toll free North America)
1 360 925 5143 (direct)
Email:
Direct returns may be performed according to the Xantrex Return Material Authorization Policy
described in your product manual. For some products, Xantrex maintains a network of regional
Authorized Service Centers. Call Xantrex or check our website to see if your product can be repaired at
one of these facilities.
975-0288-01-01
WA–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Return
What proof of purchase is required? In any warranty claim, dated proof of purchase must
accompany the product and the product must not have been disassembled or modified without prior
written authorization by Xantrex.
Proof of purchase may be in any one of the following forms:
•
•
•
The dated purchase receipt from the original purchase of the product at point of sale to the end user,
or
The dated dealer invoice or purchase receipt showing original equipment manufacturer (OEM)
status, or
The dated invoice or purchase receipt showing the product exchanged under warranty
What does this warranty not cover? This Limited Warranty does not cover normal wear and tear of
the product or costs related to the removal, installation, or troubleshooting of the customer's electrical
systems. This warranty does not apply to and Xantrex will not be responsible for any defect in or
damage to:
a) the product if it has been misused, neglected, improperly installed, physically damaged or altered,
either internally or externally, or damaged from improper use or use in an unsuitable environment;
b) the product if it has been subjected to fire, water, generalized corrosion, biological infestations, or
input voltage that creates operating conditions beyond the maximum or minimum limits listed in
the Xantrex product specifications including high input voltage from generators and lightning
strikes;
c) the product if repairs have been done to it other than by Xantrex or its authorized service centers
(hereafter "ASCs");
d) the product if it is used as a component part of a product expressly warranted by another manufac-
turer;
e) the product if its original identification (trade-mark, serial number) markings have been defaced,
altered, or removed.
Disclaimer
Product
THIS LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED BY XANTREX IN
CONNECTION WITH YOUR XANTREX PRODUCT AND IS, WHERE PERMITTED BY LAW, IN LIEU OF ALL OTHER
WARRANTIES, CONDITIONS, GUARANTEES, REPRESENTATIONS, OBLIGATIONS AND LIABILITIES, EXPRESS OR
IMPLIED, STATUTORY OR OTHERWISE IN CONNECTION WITH THE PRODUCT, HOWEVER ARISING (WHETHER
BY CONTRACT, TORT, NEGLIGENCE, PRINCIPLES OF MANUFACTURER'S LIABILITY, OPERATION OF LAW,
CONDUCT, STATEMENT OR OTHERWISE), INCLUDING WITHOUT RESTRICTION ANY IMPLIED WARRANTY OR
CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE TO THE EXTENT REQUIRED
UNDER APPLICABLE LAW TO APPLY TO THE PRODUCT SHALL BE LIMITED IN DURATION TO THE PERIOD
STIPULATED UNDER THIS LIMITED WARRANTY.
IN NO EVENT WILL XANTREX BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, LOSSES, COSTS OR EXPENSES HOWEVER ARISING WHETHER IN CONTRACT OR TORT INCLUDING
WITHOUT RESTRICTION ANY ECONOMIC LOSSES OF ANY KIND, ANY LOSS OR DAMAGE TO PROPERTY, ANY
PERSONAL INJURY, ANY DAMAGE OR INJURY ARISING FROM OR AS A RESULT OF MISUSE OR ABUSE, OR THE
INCORRECT INSTALLATION, INTEGRATION OR OPERATION OF THE PRODUCT.
WA–2
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Return
Exclusions
If this product is a consumer product, federal law does not allow an exclusion of implied warranties. To
the extent you are entitled to implied warranties under federal law, to the extent permitted by applicable
law they are limited to the duration of this Limited Warranty. Some states and provinces do not allow
limitations or exclusions on implied warranties or on the duration of an implied warranty or on the
limitation or exclusion of incidental or consequential damages, so the above limitation(s) or
exclusion(s) may not apply to you. This Limited Warranty gives you specific legal rights. You may have
other rights which may vary from state to state or province to province.
Return Material Authorization Policy
Before returning a product directly to Xantrex you must obtain a Return Material Authorization (RMA)
number and the correct factory "Ship To" address. Products must also be shipped prepaid. Product
shipments will be refused and returned at your expense if they are unauthorized, returned without an
RMA number clearly marked on the outside of the shipping box, if they are shipped collect, or if they
are shipped to the wrong location.
When you contact Xantrex to obtain service, please have your instruction manual ready for reference
and be prepared to supply:
•
•
•
•
The serial number of your product
Information about the installation and use of the unit
Information about the failure and/or reason for the return
A copy of your dated proof of purchase
Record these details in “Information About Your System” on page WA–5.
Return Procedure
1. Package the unit safely, preferably using the original box and packing materials. Please ensure that
your product is shipped fully insured in the original packaging or equivalent. This warranty will not
apply where the product is damaged due to improper packaging.
2. Include the following:
•
The RMA number supplied by Xantrex Technology Inc. clearly marked on the outside of the
box.
•
•
•
A return address where the unit can be shipped. Post office boxes are not acceptable.
A contact telephone number where you can be reached during work hours.
A brief description of the problem.
3. Ship the unit prepaid to the address provided by your Xantrex customer service representative.
If you are returning a product from outside of the USA or Canada In addition to the above, you
MUST include return freight funds and are fully responsible for all documents, duties, tariffs, and
deposits.
If you are returning a product to a Xantrex Authorized Service Center (ASC) A Xantrex return
material authorization (RMA) number is not required. However, you must contact the ASC prior to
returning the product or presenting the unit to verify any return procedures that may apply to that
particular facility and that the ASC repairs this particular Xantrex product.
975-0288-01-01
WA–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Return
Out of Warranty Service
If the warranty period for your PowerHub 1800 has expired, if the unit was damaged by misuse or
incorrect installation, if other conditions of the warranty have not been met, or if no dated proof of
purchase is available, your unit may be serviced or replaced for a flat fee.
To return your PowerHub 1800 for out of warranty service, contact Xantrex Customer Service for a
Return Material Authorization (RMA) number and follow the other steps outlined in “Return
Procedure” on page WA–3.
Payment options such as credit card or money order will be explained by the Customer Service
Representative. In cases where the minimum flat fee does not apply, as with incomplete units or units
with excessive damage, an additional fee will be charged. If applicable, you will be contacted by
Customer Service once your unit has been received.
WA–4
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Return
Information About Your System
As soon as you open your PowerHub 1800 package, record the following information and be sure to
keep your proof of purchase.
_________________________________
PH1800-GFP
❐ Serial Number
❐ Product Number
❐ Purchased From
❐ Purchase Date
_________________________________
_________________________________
If you need to contact Customer Service, please record the following details before calling. This
information will help our representatives give you better service.
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
❐ Type of installation (e.g. wind, solar, ac grid etc.)
❐ Length of time inverter has been installed
❐ Battery/battery bank size
❐ Battery type (e.g. sealed gel cell, sealed AGM)
❐ AC and DC wiring sizes and lengths
❐ Alarm sounding?
❐ Description of indicators on front panel
❐ Appliances operating when problem occurred
❐ Description of problem
________________________________________________________________________________
________________________________________________________________________________
975-0288-01-01
WA–5
Download from Www.Somanuals.com. All Manuals Search And Download.
WA–6
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Xantrex Technology Inc.
1 800 670 0707 Tel toll free NA
1 360 925 5097 Tel direct
1 800 994 7828 Fax toll free NA
1 360 925 5143 Fax direct
customerservice@xantrex.com
Printed in China
975-0288-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
|