EVERYTHING FOR THE PERFECT DIVE...
Buoyancy
Compensator
Owner’s
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BC Owner’s Manual 3.
Table of Contents
GENERAL WARNINGS & PRECAUTIONS........................................4
INTRODUCTION.........................................................................5
INTENDED USE & FUNCTION........................................................5
OVERVIEW OF STANDARD FEATURES............................................6
PREPARATION & SETUP.............................................................10
INTEGRATED WEIGHT SYSTEMS.................................................12
X-LOCK™ WEIGHT POCKET SYSTEM INSTALLATION...................13
PRE-DIVE INSPECTION...............................................................15
DIVING WITH YOUR XS SCUBA BC..............................................16
POST DIVE CARE & MAINTENANCE..............................................20
OPTIONAL ACCESSORIES & SPECIAL FEATURES.........................20
DEALER INSPECTION & SERVICE................................................21
WARRANTY.............................................................................22
DEALER INSPECTION & SERVICE RECORD..................................23
This owner’s manual is copyrighted, all rights reserved. It may not, in whole or in part,
be copied, photocopied, reproduced, translated or reduced to any electronic medium or
machine readable form without prior consent in writing from XS Scuba, Inc
XS Scuba, the XS logo, Advantage, Nekton, Paragon, X-Lock Weight Release System,
Micro Pac, AirWave Inline, are registered and unregistered trademarks of XS Scuba. All
rights are reserved. All other names are trademarks of their respective owners.
© 2005 XS Scuba BC Owner’s Manual, PN BCM-0305
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
.4 BC Owner’s Manual
General Precautions and Warnings
• Do not use this Buoyancy Compensator (BC) if you have not received supervised
instruction and certification in SCUBA diving and buoyancy control from a recognized
training agency. USE OF SCUBA EQUIPMENT BY UNCERTIFIED OR UNTRAINED
PERSONS IS DANGEROUS AND CAN RESULT IN SERIOUS INJURY OR DEATH.
• Before using this BC, it is important to completely read and understand all of the
instructions provided in this owner’s manual, any accompanying inserts, and labels or
markings affixed to the BC. IF YOU HAVE ANY QUESTIONS OR DO NOT COMPLETELY
UNDERSTAND THESE INSTRUCTIONS, CONSULT YOUR AUTHORIZED XS SCUBA
DEALER.
• Before diving with this BC in open water, it is important to familiarize yourself with
it first in confined shallow water with the assistance and supervision of an instructor
or experienced buddy. DO NOT ENTER OPEN WATER UNTIL YOU HAVE WEIGHTED
YOURSELF PROPERLY AND HAVE BECOME COMFORTABLE WITH USING ALL OF ITS
FEATURES AND ADJUSTMENTS.
• Before every dive, perform a complete pre-dive inspection following the instructions
provided in this manual. Check to ensure that all valves are functioning properly and no
signs of damage or leaks are present. IF ANY SIGNS OF DAMAGE OR MALFUNCTION
ARE FOUND, DO NOT DIVE WITH THE BC UNTIL IT HAS RECEIVED SERVICE FROM
AN AUTHORIZED XS SCUBA DEALER.
• Before entering the water, check to ensure that you can remove and ditch your
weight quickly and easily, without any obstruction or entanglement with any hoses or
accessories. IN THE EVENT OF AN OUT OF AIR EMERGENCY OR UNCONTROLLED
DESCENT, DO NOT HESITATE TO REMOVE AND DITCH WEIGHT.
• DO NOT USE YOUR BC TO LIFT HEAVY OBJECTS TO THE SURFACE. Doing so may
cause permanent damage to the BC, and could easily result in an uncontrolled ascent.
• DO NOT over inflate your BC or rely on using the power inflator to lift yourself toward
the surface. Control all ascents. A RAPID, UNCONTROLLED ASCENT MAY CAUSE
ARTERIAL GAS EMBOLISM OR DECOMPRESSION SICKNESS, AND COULD LEAD TO
SERIOUS INJURY OR DEATH.
• IN THE EVENT OF AN UNCONTROLLED, RAPID ASCENT, IT IS IMPORTANT TO
IMMEDIATELY VENT AS MUCH AIR AS POSSIBLE FROM THE BC TO SLOW YOUR
ASCENT RATE. CONTINUE VENTING AIR TO SLOW YOUR ASCENT RATE IF NEUTRAL
BUOYANCY CANNOT BE REESTABLISHED.
• DO NOT attempt to modify your XS Scuba BC for use with more than one cylinder.
Doing so could damage the structural integrity of the BC’s backpack and harness system,
and could lead to its failure underwater.
• DO NOT INHALE FROM YOUR ORAL INFLATOR. The BC air cell may contain harmful
contaminants or gasses, which could cause suffocation, serious injury, and infection of
the lungs.
• It is important to obtain factory prescribed service for this BC from an Authorized XS
Scuba Dealer at least once each year, or according to the same scheduled intervals for
your regulator. Annual service consists of a complete overhaul of the power inflator, and
a general air leak inspection of the air cell and valve connections.
• Disassembly, repair, or lubrication must only be performed by persons who are factory
trained and authorized by XS Scuba. UNAUTHORIZED SERVICE WILL RENDER THE
WARRANTY NULL AND VOID, AND COULD CAUSE THE BC TO MALFUNCTION.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
BC Owner’s Manual 5.
Introduction
Thank you for choosing XS Scuba. Your new BC has been designed, manufactured
and individually tested to ensure that it consistently meets the highest performance
and safety standards possible. This Owner’s Manual describes the unique functions
and features of XS Scuba’s BC equipment and various optional accessories. By
following the instructions in this manual, you will understand how your BC works,
how to make best use of its features, and how to ensure that it lasts a long time. It
is very important to take the time to read the instructions provided in this manual.
If you have any questions, please consult your Authorized XS Scuba Dealer.
Intended Use & Function of Your BC
The main purpose for wearing a Buoyancy Compensator is to achieve and maintain
neutral buoyancy at all times while you are underwater, regardless of changes in
depth or cylinder pressure. This allows you to be much more relaxed while you
dive – and safer – since you won’t need to struggle against the forces of positive
and negative buoyancy. Modern jacket and back inflation style BC’s provide
the most effective and streamlined buoyancy control, since they are specifically
designed to support the diver in a comfortably balanced, face-down position while
swimming underwater. Stress and exertion can now be minimized, if not eliminated
altogether.
Since the introduction of the jacket style and back inflation designs, the modern
BC has evolved into a consolidated harness and pack system that carries the
cylinder and serves as a fixture point for first stage regulators, instrumentation,
and accessories. For even greater convenience and comfort, many models are now
available with integrated weight systems that can supplement or replace the weight
belt.
Your BC can also provide you with non-emergency flotation to help you rest on the
surface, but you should never rely on it to function as a life preserver or personal
flotation device (PFD). In order to meet approval by U.S. Coast Guard regulations,
a PFD must be designed so that it automatically rights you to a face-up position
and supports your head out of the water on the surface to prevent drowning. The
design characteristics and intended function of a PFD are therefore very different
from those of a BC, since a PFD is specifically designed to function on the surface
and a BC is primarily designed to function underwater.
It is important to remember that other equipment you wear in addition to your
BC, including your cylinder, exposure suit, or weight system, will also affect your
position in the water. An empty cylinder, for instance, can create counter-buoyancy
that could roll you into a face down position if you were to lose consciousness.
For this reason, XS Scuba recommends that you always dive with a buddy, and
remain close enough to them to be able to render assistance to each other in the
event of an emergency. Do not depend on your BC, exposure suit, or any other
equipment to hold your face above the surface in the event that you are rendered
unconscious in the water while diving.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
.6 BC Owner’s Manual
Standard Features
WARNING: A Buoyancy Compensator (BC) is NOT a life jacket! It is
not designed to provide face-up flotation in all situations, and it does
not meet U.S. Coast Guard regulations for a life preserver or personal
flotation device (PFD). If you become unconscious in the water without
a buddy present to immediately assist, you may suffer serious injury or
death from drowning.
Overview of Standard Features & Adjustments
Please take the time to acquaint yourself with your BC’s features, including
standard inflation/deflation valves and adjustments that can be found on every
model of an XS Scuba BC. Specific instructions for using these features will be
provided throughout this manual. Additional options and special features will
be explained in the section titled Optional Accessories & Special Features.
Valves
Integrated Inflator System – With this system, you have two methods to inflate
the BC, two methods to deflate the BC, and automatic venting of excess
pressure. Be sure to read and understand these instructions describing how
this system operates before attempting to dive with your XS Scuba BC.
Power Inflator – This assembly is actually made up of
two different valves. The oral inflation valve can be
used to manually inflate or deflate your BC. The power
inflation valve is connected directly to your regulator’s
first stage, and can be used to inflate your BC with the
push of a button.
Overpressure Relief Valve (OPV) / Rapid Exhaust Valve
(REV) – The integrated Overpressure Relief Valve (OPV)
vents excess pressure from the BC during ascent or if
over-pressurized from the power inflator. This component
of the Integrated Inflator System operates automatically
so no instructions for its manual use are necessary.
The Rapid Exhaust Valve (REV), located within
the upper shoulder unit of the integrated inflator, is
connected to the lower Power Inflator by a cable located
inside the corrugated hose. This valve can be opened to
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
BC Owner’s Manual 7.
vent air by pulling the power inflator straight down. It works best while you are
in a vertical heads-up position or in a face-down swimming position.
WARNING: The OPV in the Integrated Inflator is set at a lower relief
pressure than the optional OPV located on the back of some BC models
to prevent damage to the material of the BC air cell. It is imperative
that the Integrated Inflator System be the only inflator used with this
BC. Never dive with the BC if the inflator does not function properly,
or if it has been tampered with, modified, or replaced with an inflator,
airway assembly, or shoulder dump of a manufacturer other than XS
Scuba.
Rear Dump Valve – This valve can be used to dump air
by pulling on the ball and cord. This Rear Dump Valve
works best while you are in a heads-down position or in
a face-down swimming position.
Primary Adjustment Points
Shoulder Straps
The shoulder straps of your BC are connected with side-
squeeze fasteners, and can be easily adjusted by pulling
upward on the buckle to loosen, or downward on the D-
ring at the end of the strap to tighten.
Cummerbund Waistband
The cummerbund is designed to provide a wide range
of adjustment to hold your BC snug and secure below
your rib cage and above your hips. All XS Scuba
cummerbunds feature a high quality Velcro® touch
fastener,andcanbeadjustedforlengthatthebackpack.
Some models feature an elastic stretch cummerbund
that can compensate for the contraction of your wetsuit
at depth. To fasten the cummerbund, simply pull the
left side containing the loop Velcro® snug across your
waist, and then pull the right side snug over it. Finally,
press firmly down to fasten the hook Velcro®.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
.8 BC Owner’s Manual
Cylinder Band with Buckle
This mechanism attaches your BC to your cylinder
so that it is securely held at the desired height,
without slipping. Some models are equipped with the
exclusive Micro Pac™ and two cylinder bands for extra
support.
The nylon webbing should already be woven through
the buckle(s), but instructions for re-weaving are
provided in the following section, titled Preparation
& Setup.
Tank Locator Strap
To ensure that your BC is set at the correct height on
the cylinder, simply loop this strap over the cylinder
valve and adjust it to raise or lower the BC. Then,
fasten the cylinder band(s).
Sternum Strap
Most models are equipped with this feature, or it
can be purchased separately as an accessory option.
Using two dimes, you can disassemble the post pin on
the female buckle to reverse the strap’s direction, or
remove it altogether.
Integrated Weight Systems
Some XS Scuba BC models are equipped with built-in compartments and
pockets to hold X-Lock™ Integrated Weight System and trim weights. Either
“soft weight” (pouches filled with lead shot) or solid weight can be used, but
soft weight is strongly recommended, since it will fill the weight compartment
to its fullest capacity and provide the maximum comfort.
If your XS Scuba BC is a weight integrated model, it is very important to read
the following instructions in order to understand the difference between these
two types of weight pockets and how to use them correctly. For installation and
removal instructions, see the following section, titled Preparation & Setup.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
BC Owner’s Manual 9.
Releasable Trim Weights
If your BC is equipped with this feature, you will find
two releasable weight compartments located on the
backside of either the air cell or the harness – on
opposite sides. These are each designed to hold up to
5 pounds (10 pounds total) of weight to supplement
and counter-balance the weight that you wear on your
weight belt or X-Lock™ Integrated Weight System.
The weight in these pockets can be “dumped” by
grasping the strap on the bottom of the pocket and
pulling downward firmly.
X-Lock™ Integrated Weight System
Some XS Scuba models are also equipped with two
X-Lock™ weight pockets, located inside the front
lower portions of the BC. These pockets can be easily
identified by their plastic pull handles that face toward
the center of the waistband. The X-Lock™ pockets
are designed to each hold a maximum weight of 10
lbs., for a combined total of 20 lbs.
Experiment with different sizes of weight until you arrive at the configuration
that best suits your personal preference and provides maximum comfort.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
.10 BC Owner’s Manual
Preparation & Setup
XS Scuba recommends that you bring your BC, together with your regulator, to
your Authorized XS Scuba Dealer for the installation of the low pressure (LP)
quick disconnect inflator hose that is provided with your BC. If it is not possible
to return with your regulator to your Authorized Dealer, you may install the LP
inflator hose by carefully performing all the steps in the following procedure.
LP Inflator Hose Installation
WARNING: DO NOT attach the low pressure inflator hose to a high
pressure (HP) port (greater than 200 psi / 13.6 bar). This may cause
the hose to burst when pressurized, which can result in serious injury.
The LP hose has a 3/8” (9.5mm) male fitting that will only fit the standard
LP ports found on most first stages, and is smaller than the standard 7/16”
(11mm) HP port. Some older regulators have HP and LP ports that are the
same size (3/8”-9.5mm). All XS Scuba regulators, and most provided by other
manufacturers, have a high-pressure port that is clearly marked “HP,” with a
small restrictive orifice that is visible when the plug is removed.
If your regulator has all 3/8” ports and you cannot decide if a port is LP or
HP, bring it with the hose to your dealer for installation.
If you can identify your regulator’s LP ports, follow this procedure:
1. To select the best LP port, mount the first stage on a cylinder valve to
determine the correct orientation and hose routing.
2. Remove the port plug from a low-pressure port on the regulator using
the appropriate size wrench or key.
3. Your BC was shipped with the LP hose connected to the power inflator.
Remove the inflator hose from the power inflator body by sliding the
grooved sleeve back while pulling the fitting off the QD nipple.
4. Check the male end of the LP hose to ensure the O-ring is present and
in good condition, and screw the threaded end of the hose into the
port. Tighten the hose to 50-60 inch pounds (7 kg/cm) with a 9/16”
wrench.
Cylinder Mounting
Threading the Cylinder Band & Buckle
NOTE: All XS Scuba BC’s are shipped with the nylon band pre-threaded
through the buckle. If rethreading is necessary, follow these steps:
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
BC Owner’s Manual 11.
1. Ensure that the metal bale of the buckle is as close to the rear of the
BC as possible. This provides the greatest range of adjustment.
2. With the buckle fully open, thread the cylinder band up the middle slot
and back down through the slot closest to the metal bale. Pull the end
to increase the tension in the band.
3. Loosely thread the webbing through the open slot in the end of the
buckle, but do not cinch it tight at this time.
Attaching the BC to the Cylinder
NOTE: Some models are equipped with the Micro Pac™ and two
cylinder band assemblies.
1. First, wet the cylinder band(s) and then fit the BC over the cylinder.
Loop the tank locator strap over the cylinder valve and adjust it as
needed to hold the BC at the desired height and position.
2. While holding the cylinder secure, pull the free end of the cylinder
band until there is a very tight fit between the pack and the cylinder.
3. Close the buckle halfway to hold the cylinder band taut, and thread the
end of the band through the open slot in the end of the buckle.
4. Pull the cam buckle closed so that it snaps down against the cylinder.
Fasten the end of the webbing securely over the loop Velcro® on the
cylinder band.
5. Test the tightness by vigorously pulling and shaking the BC by the
shoulder straps.
WARNING: The cylinder band may initially stretch after it becomes wet.
Always wet the band prior to attaching your BC to the cylinder and apply
enough tension to ensure that the cylinder is held completely secure.
Test this connection before every dive. If the cylinder is allowed to slip
free from the BC while you are diving, you could become separated
from your air supply, which could result in serious injury or death.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
.12 BC Owner’s Manual
Integrated Weight System
Releasable Trim Weights
To install weight in each compartment, unfasten the Velcro® to open each
flap. Insert the desired weight and refasten the Velcro® flap.
It is important to remember at all times that weight installed in these
compartments MAY NOT be easily released during an emergency situation.
Before diving with trim weight installed in your BC, it is extremely important
to check your buoyancy in shallow water while wearing the BC attached to a
fully charged cylinder. While standing in chest deep water, completely deflate
the BC and verify that you can easily achieve positive buoyancy by ditching
your X-Lock™ Integrated Weight System pockets. For more information about
weighting and performing a buoyancy check, refer to the section titled, Diving
with Your XS Scuba BC.
WARNING: The trim weight compartments should only be loaded
with weight that supplements the releasable weight carried on your
weight belt or your BC’s X-Lock™ Integrated Weight System pockets.
Do not install weight into the trim weight compartments unless you
are certain you can achieve positive buoyancy at depth by ditching
your releasable weight while your BC is completely deflated. You
may otherwise experience difficulty ascending to the surface in an
emergency situation, which could lead to serious injury or death due
to drowning.
X-Lock™ Integrated Weight System
Filling the Weight Pockets
To fill the X-Lock™ Integrated Weight System pockets with weight, it will be
necessary to first remove each one from its respective compartment by firmly
pulling the release handle straight out, toward the opposite side of the BC.
Open the sealed flap, and fold it back out of the way.
While holding the pocket fully open, insert the weight
and then close the flap. When each pocket has been
loaded with weight, firmly run your hand over the flaps
to seal the Velcro® fastener securely in place.
When filling the X-Lock™ Integrated Weight System
pockets, it is important to fill each pocket with the
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
BC Owner’s Manual 13.
same amount of weight in order to provide optimum balance in the water. You
may otherwise experience a tendency to roll to one side if one pocket is more
heavily loaded than the other.
X-Lock™ Integrated Weight System Pocket Installation
WARNING: Before every dive, it is important to inspect the condition
of all connections between the X-Lock™ Integrated Weight System
pockets and the BC to ensure that they are clean and free of any
wear or damage that may impair their function. Carefully follow the
instructions provided below to install the pockets correctly and ensure
that all connections are securely sealed. Accidental release of the
weight pockets may otherwise result in an uncontrolled ascent, which
could lead to serious injury or death due to embolism or decompression
sickness.
The weight pockets should be installed while the BC is fully deflated, either
before or after it has been donned. It is easier, however, to install them before
donning the BC. If the weight pockets are filled to their maximum capacity
and installed into the BC, XS Scuba strongly recommends that you seek the
assistance of a buddy before attempting to don the BC. You may otherwise risk
injury, due to muscle strain or a temporary loss of balance.
NOTE: If the amount of weight being used does not fill the pocket to
capacity, turn the pocket over to slide the weight as far forward inside
the pocket as possible, toward the closure flap. After the X-Lock™
pocket has been correctly installed, a Velcro® connection inside the
BC compartment will hold the end of the pocket closed to prevent the
weight from shifting.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
.14 BC Owner’s Manual
To install either pocket, slide the closed end into the opening of the
compartment, with the band of loop Velcro® facing up. Guide it firmly inward
until the Velcro® connection has fully engaged near the end of the compartment.
Then, fold the pocket’s retaining flap over the Velcro® connection on the outside
of the BC, and firmly run your hand over the flap. Finally, secure the release
buckle.
For information about using the X-Lock™ Integrated Weight System and
ditching weight, refer to the section titled, Diving with Your XS Scuba BC.
Donning the BC
CAUTION: To avoid possible injury and/or damage to your equipment,
XS Scuba recommends that you should always don your BC with
assistance from a buddy.
1. Ensure that the side-squeeze buckles of both shoulder straps are securely
fastened. Fully extend each strap to its maximum length by pulling up on
the tab of the lower slide buckle, and then pulling the webbing down until
the D-ring slides up near the buckle.
2. While your dive buddy holds the cylinder supported behind you, reach back
to place your arms through the shoulder straps.
3. While your buddy continues to hold the cylinder, fasten the cummerbund
snug around your waist (not hips). The best positioning is between your
hips and your rib cage. The weight of the cylinder should rest on the
lumbar region (lower part) of your back.
4. After your buddy has released the cylinder and the BC feels comfortably
supported on your hips and shoulders, bend forward at the waist and adjust
the shoulder straps to a comfortable length by pulling straight down on the
D-rings.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
BC Owner’s Manual 15.
NOTE: Remember, adjusting the shoulder straps too tightly will transfer
the cylinder weight from the hips onto the shoulders, and may restrict
your arm movement.
5. Readjust the cummerbund, if necessary, so that it is comfortably snug but
not restricting, with an overlap of at least 3 inches. Fasten together the
male and female side-squeeze buckles of the outer waist strap over the
cummerbund.
NOTE: Your BC is equipped with an elastic outer waist strap. It can
be adjusted inside the BC, behind the cummerbund, so that it will be
snug when fastened. This will help your cummerbund to remain snug
when your wetsuit becomes compressed at depth, and can also help
prevent squeeze when your BC is inflated on the surface.
6. Fasten the sternum and waist straps, if equipped, and pull the free ends
until they are comfortably snug but not restricting.
WARNING: Be sure to avoid over tightening your BC’s adjustments.
Check to ensure that you can move your arms comfortably and take
deep, full breaths. Over tightening can restrict your respiration and
blood circulation, which can lead to serious injury or death.
Pre-Dive Inspection
Before each use, the BC must be visually inspected and tested. NEVER dive
with a BC that shows any signs of damage to its air cell or valves until it has
been serviced by an Authorized XS Scuba Dealer.
Inspection Checklist:
1. Connect the power inflator to a clean air source via the LP quick disconnect
hose. Depress and release the inflator button intermittently to ensure that
the airflow is unobstructed, and that the airflow stops completely when the
button is released.
2. Ensure that the air cell does not contain any water from a previous dive or
from internal rinsing. An excessive amount of water inside the air cell can
reduce the BC’s internal air volume and lift capacity.
3. Manually operate the lower overpressure valve (OPV) by pulling on the
attached ball and cord to release air from inside the BC, and then fully
inflate the BC until the shoulder OPV valve opens. Examine the operation
of the shoulder OPV valve by repeatedly inflating the BC to ensure that it
opens to relieve excess pressure, yet close immediately afterward to allow
the air cell to remain fully inflated.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
.16 BC Owner’s Manual
4. Check the function of the oral inflator button, rapid exhaust valve (REV),
and OPV to ensure a rapid and unobstructed exhaust from each valve.
Fully inflate the BC once again, and disconnect the Power Inflator to listen
for any leakage.
CAUTION: If any leakage can be heard, or if the air cell begins to
deflate within 5-10 minutes, DO NOT attempt to use the BC until it
has received service from an Authorized XS Scuba Dealer.
5. Make a final check of the cylinder band’s tension to ensure that it is as
tight as possible and the cylinder is securely held without any noticeable
slippage. Retighten if necessary.
6. Before entering the water, check the trim weight compartments to ensure
they are closed, and the X-Lock™ Integrated Weight System pockets to
ensure that they are correctly installed into to the BC. Refer to X-Lock™
Weight System Pocket Installation for details.
WARNING: The X-Lock™ Integrated Weight System pockets may fall
out unexpectedly if the buckle connections are not securely fastened.
Involuntary release of both weight pockets can cause a sudden increase
in buoyancy and rapid ascent, and could lead to serious injury or death
due to arterial gas embolism or decompression sickness.
Diving With Your XS Scuba BC
Rules For Personal Weighting
Before diving with your new XS Scuba BC, it is important to establish the
correct amount of weight you will need to wear to achieve neutral buoyancy,
without being too heavy (negatively buoyant) or light (positively buoyant). While
following the procedures taught in an open-water training course, it is important
to observe some basic rules for properly weighting yourself:
1. Be aware of the factors that can cause your personal buoyancy to change,
including personal weight loss or gain, the type and thickness of
the exposure suit you wear, and the buoyancy characteristics of your
cylinder when it is full and empty.
2. Weight yourself in chest deep water while wearing all your equipment,
including your exposure suit and BC, and with the cylinder you will be
using while it contains no more than 500 psi.
3. Experiment with different amounts of weight until you are able to float at
eye level on the surface while holding your breath, and slowly begin to sink
as you exhale.
4. Conduct a personal buoyancy check whenever your body weight has changed,
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
BC Owner’s Manual 17.
or if you use a different cylinder, BC, or exposure suit.
Diving With an X-Lock™ Integrated Weight System
It is important to remember that the X-Lock™ Integrated Weight System
pockets are connected to the BC independently of each other, unlike a weight
belt that has only one release mechanism, and must be released accordingly.
This feature provides you with the advantage of being able to ditch only half
your weight initially, and thereby maintain better control of your ascent rate in
an emergency.
In the event of an emergency that requires you to ditch your weight, firmly
pull the release handle of each weight pocket towards the opposite side of your
waist. When the pocket is completely disengaged from its compartment, hold
it out and away from your body before dropping it.
CAUTION: To avoid injuring other divers, always look below you before
dropping weight.
WARNING: Always ensure that your X-Lock™ Integrated Weight
System is not obstructed by any straps, lines, etc. DO NOT add weight
to your BC anywhere other than the designated weight compartments,
since doing so may prevent you from being able to ditch weight in
an emergency. Failure to ditch weight in an emergency may lead to
serious injury or death due to drowning.
Before diving with a BC that features a X-Lock™ Integrated Weight System,
it is very important to explain its function and design to your dive buddy. Thus
will ensure that they are as familiar with it as you are so they can assist you in
case of an emergency.
Inflating Your BC
Oral Inflation
To orally inflate your BC, hold the oral inflator
mouthpiece to your mouth and depress the oral inflator
button while exhaling into the mouthpiece. Release
the button when done or while taking another breath,
and repeat this procedure until the BC is satisfactorily
inflated.
NOTE: Oral inflation of your BC underwater is a practiced skill that
must be achieved under the supervision of your diving instructor,
since it requires the removal of your second stage regulator from your
mouth.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
.18 BC Owner’s Manual
Power Inflation
To connect the LP hose, grip the grooved sleeve at the connection fitting
between your thumb and forefinger, and slide the sleeve back. Place the fitting
over the inflator valve QD nipple, and firmly push inward while releasing the
sleeve. Check to ensure that the hose is securely attached.
To inflate your BC, depress the power inflator button. DO NOT hold the
inflator button depressed continuously underwater, as this could cause you to
become excessively buoyant. Instead, depress the button in short bursts until
you become neutrally buoyant.
WARNING: Do not rely on the power inflator as the only means for
inflating your BC. It is important to maintain proficiency in the skill
of orally inflating your BC. You may otherwise be unable to achieve
positive buoyancy in an emergency situation, which could lead to
serious injury or death.
Venting & Dumping Air
Throughout the course of a dive, it will be necessary to vent or dump air from
the BC using one of the three methods described in the following instructions.
Each method uses a valve that is in a different location, and is designed either to
vent air or dump it very quickly. The method you should choose will depend on
whether you are descending feet-first, head-first, maintaining neutral buoyancy
underwater, or controlling your ascent. To release air as effectively as possible,
remember to utilize the valve that is at the highest point on the BC and nearest
to the surface, depending on your position in the water.
WARNING: Wheneveryouascend, whetherintentionallyoraccidentally,
you must simultaneously vent air from the BC as needed to maintain
buoyancy control. If air is allowed to expand inside the BC unchecked,
you may experience a rapid, uncontrolled ascent, which could lead to
serious injury or death due to arterial gas embolism, decompression
sickness, or drowning.
To regain buoyancy control during an
uncontrolled ascent, you must dump air from the BC as quickly as
possible until you have stopped ascending.
Venting With the Oral Inflator
Air can be vented through the inflator by holding the inflator above your
head and depressing the oral inflator button. This method is recommended for
making an initial feet-first descent, but is not as effective while you are in a
facedown swimming position.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
BC Owner’s Manual 19.
NOTE: Depressing the oral inflator while the BC is empty may allow
water to enter the air cell.
Venting With the REV
Inside the power inflator’s corrugated hose is a cable that attaches the power
inflator to the rapid exhaust valve at the top of the airway assembly. You can
thus vent air from the BC by pulling straight down on the power inflator.
The amount of air vented depends on how far open the exhaust valve is (i.e.,
the distance you pull the inner cable) and how long it is open. Short pulls vent
small amounts of air for minor changes in buoyancy, and a long pull will vent
the entire BC in a matter of seconds.
You retain just as much control over your buoyancy using the Rapid Exhaust
Valve as with the oral inflator button. You also get the benefit of eliminating
water entry even if the exhaust valve remains open after release of all the air.
This valve provides an effective and convenient way to vent air from the BC
while you are in either an upright or face-down swimming position, and is more
convenient to use than the oral inflator.
Rear Dump Valve – If your BC has a Rear Dump Valve located on the lower rear
portion of the air cell, it can be opened manually to quickly dump air by pulling
on the ball and cord assembly. This valve works best while making a head-first
descent, or in a face-down swimming position.
CAUTION: The proper function of the overpressure relief valve is
essential to prevent damage to the BC air cell. Unauthorized service
or tampering may render this valve inoperable, and could cause the air
cell to leak or burst. This type of damage is not repairable, and is not
covered under the terms and conditions of the XS Scuba Warranty.
NOTE: Most training agencies recommend that you should descend
in an upright, feet-first position, in order to maintain a slower and
more controlled descent. This is especially true if you experience
difficulty equalizing your ears, or if you are descending in low visibility
conditions.
Right Shoulder OPV / Dump Valve (not featured on all models)
Some models may featurea redundant OPV/Dump valve, located
at the top of the right shoulder. A ball and cord assembly
extends to the shoulder buckle assembly for quick dumping
of air.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
.20 BC Owner’s Manual
Post Dive Care & Maintenance
With proper care, your XS Scuba BC will provide many years of reliable
service. The following preventative maintenance must be performed to extend
the life of your BC:
• Avoid prolonged exposure to direct sunlight and extreme heat. Nylon fabric
can quickly fade when exposed to the sun’s ultraviolet rays, and extreme
heat may damage the welded seams of the BC’s air cell.
• Avoid repeated or prolonged use in heavily chlorinated water, which can
cause the BC fabric to discolor and decay prematurely.
• Do not allow the BC to chafe against any sharp objects or rough surfaces
that could abrade or puncture the air cell. Do not set or drop heavy objects
such as block weights on the BC.
• Avoid any contact with oil, gasoline, aerosols, or chemical solvents.
• To preserve the life of the air cell, thoroughly rinse it inside and out with
fresh water after every day of use, following these steps:
1. Pressurize the power inflator with low pressure air via the LP hose.
2. Using a garden hose, direct water through the oral inflator to flush
the interior of the air cell, and then thoroughly rinse the exterior of
the BC. Before rinsing, ensure that the power inflator is pressurized
with air. This will prevent debris and contaminants from entering
the inflator valve if the inflator button is accidentally depressed.
3. Completely drain the air cell of water through the lower OPV/dump
valve by pulling the ball/cord assembly.
4. Fully inflate the BC, and allow it to dry inside and out. Then store
it partially inflated, away from direct sunlight, and in a clean, dry
area. Do not store the BC in an enclosed space, such as a car
trunk, where it may be exposed to temperatures below 0º F
(-18º C) or above 120º F (49º C).
5. To avoid stress on the air cell or harness assembly, remove all
weight from the trim weight and X-Lock™ releasable compartments
before storing the BC. Soft weights especially, can discolor the BC
over time.
CAUTION: DO NOT attempt to perform any disassembly or service
of your XS Scuba BC. Service requiring disassembly must only be
performed by a factory trained XS Scuba technician. To obtain any
service or repair, it is important to bring your BC to an Authorized XS
Scuba Dealer.
Optional Accessories & Special Features
You can purchase the following accessories for your new BC from your Authorized
XS Scuba Dealer:
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
BC Owner’s Manual 21.
Safety Tube (part no. AC190)
This high-visibility surface signal device can be inflated to a
length of 6’, and is carried inside a compact 5”x35” nylon
mesh bag that can be clipped to your BC or stored in a
pocket.
AirWave Inline™ Octopus
(part no. RG325)
Tostreamlineyoursystemwithfewer
hoses and keep your octopus where
you’ll always be able to find it, you’ll
want the AirWave Inline™ Octopus – a backup second
stage regulator that is worn on your BC connected by
your power inflator. This option is available separately
from your Authorized XS Scuba Dealer, and can be
added to any XS Scuba BC.
Dealer Inspection & Service
1. Do not assume that a BC is in good working condition just because it has
had little use since its last servicing. Prolonged or improper storage can
still result in internal corrosion and/or deterioration of O-ring seals and
valve springs, as well as air cell seam degradation.
2. You should obtain factory-authorized service for your BC at least once a
year from an Authorized XS Scuba Dealer, regardless of the amount of use
it has received. This service includes a general air leak inspection and
complete overhaul of the power inflator and OPV valve(s). Your BC may
require this service more frequently, depending on the amount of use
and quality of maintenance that it receives.
3. If the BC is used for rental or training purposes, it will require complete
overhaul and service every three to six months. Chlorinated swimming
pool water is an especially damaging environment for SCUBA equipment,
due to the high level of chlorine and pH balance chemicals which cause
certain parts to rapidly deteriorate.
4. DO NOT attempt to perform any disassembly or service of your BC. Doing
so may cause the BC to malfunction, and will render the XS Scuba
Warranty null and void. All service must be performed by an Authorized
XS Scuba Dealer.
HAVE YOUR BC SERVICED AT LEAST ONCE A YEAR FROM AN AUTHORIZED
XS SCUBA DEALER. YOUR PERSONAL SAFETY AND THE MECHANICAL
INTEGRITY OF YOUR BC MAY DEPEND ON IT.
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
.22 BC Owner’s Manual
Limited Two-Year Warranty
XS Scuba, Inc. warrants to the original owner, this product to be free of
defects in materials and/or workmanship for a period of two years from date of
original purchase. Warranty applies only under normal sport and skin diving
use and with proper care and maintenance. This warranty is non-transferable
and limited to repair or replacement at the discretion of XS Scuba. BC must be
returned with proof of purchase.
What Is Covered
All non-wearing valve parts and the welded seams of the BC air cell are
covered under this warranty. Should any part of your XS Scuba BC be found
defective, XS Scuba, at its discretion, will repair or replace the component at
no charge to you.
What Is Not Covered
1. This warranty does not extend to abrasion, punctures, or tears of the air
cell, or seam separation caused by chemical attack; including, but not
limited to prolonged exposure to chlorine or other pool chemicals.
2. This warranty does not extend to damages caused by improper use,
improper maintenance, neglect, unauthorized repairs, modifications,
accidents, fire, or casualty.
3. Cosmetic damage, such as scratches, fraying, and nicks are not covered by
this warranty.
4. This warranty does not extend to equipment used for rental, commercial,
or military purposes.
What You Need To Do
1. Keep a copy of the original purchase receipt and subsequent inspections
with this manual.
2. Your XS Scuba BC should be inspected and serviced by an authorized
XS Scuba repair facility at least once a year.
3. Provide proof of original purchase and annual servicing by an Authorized
XS Scuba Dealer in the form of receipts/invoices.
Disclaimers / Exclusions
Thiswarrantyisnontransferablefromtheoriginalowner. Nosalesperson,dealer
or representative is authorized to make any modification to this warranty.
It is dangerous for untrained and uncertified persons to use the equipment
covered by this warranty. Therefore, use of this equipment by an untrained
person renders any and all warranties null and void. Use of SCUBA equipment
by anyone who is not a trained and certified diver, or receiving training under
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
BC Owner’s Manual 23.
the supervision of an instructor, could lead to serious injury or death.
This warranty gives you specific legal rights. You may have rights, which vary
from state to state and country to country.
XS SCUBA DISCLAIMS AND EXCLUDES ANY LIABILITY FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states in the U.S. and certain foreign
countries do not allow exclusions or limitations of liability for incidental,
consequential, or indirect costs, expenses, or damages incurred while using
this product, so this may not apply to you.
Returning Your BC For Service
Whenever your BC requires annual service or warranty repair, it is important to
bring it to an Authorized XS Scuba Dealer. Be sure to provide the dealer with
photocopies of your original sales receipt and service records. For the location
of the dealer nearest you or additional information, visit our website at: www.
XSscuba.com.
Service Record
Model: _______________ Serial Number: ______________ Purchase Date: ___________
XS Scuba Dealer: ____________________________________________________________
Address: ___________________________________________________________________
_________________________________________ Phone: ___________________________
SERVICE #1
XS Scuba Dealer: ____________________________________________________________
Technician Signature: _______________________________ Date: ___________________
SERVICE #2
XS Scuba Dealer: ____________________________________________________________
Technician Signature: _______________________________ Date: ___________________
SERVICE #3
XS Scuba Dealer: ____________________________________________________________
Technician Signature: _______________________________ Date: ___________________
XS Scuba, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
2740 S. Harbor Blvd., Suite E
Santa Ana, CA 92704
tel: 714.424.0434
fax: 714.424.0454
©2005 XS Scuba, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|