Model D4041
Miter Saw Stand
Instruction Sheet
Introduction
The Model D4041 Miter Saw Work Stand (Figure 1)
features a universal, adjustable T-track mounting system
for securing miter saws without modification. Laterally
and vertically adjustable ball bearing rollers on each
end of the stand support long workpieces. Roller mounts
rotate incrementally for fine height adjustment. Folding
legs and rubber wheels make this work stand portable.
Unpacking
This item was carefully packaged for safe transportation.
If you notice that it was damaged during shipping, please
contact your Shop Fox dealer immediately.
Figure 1. Model D4041.
TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY WHEN USING THIS ITEM:
1. MITER SAW SAFETY. Follow all safety instruc- 5. WORKPIECE BALANCE. Use extra support
tions in the miter saw manual.
tables, or get assistance, when working with
large workpieces to prevent the stand from
tipping over.
2. MITER SAW WORK STAND SET UP. Make sure
the leg locking pins are fully snapped into
place before mounting the miter saw.
6. ATTACH MITER SAW SECURELY. DO NOT
operate the miter saw unless it is securely
attached to the miter saw work stand.
3. MITER SAW WORK STAND PLACEMENT. Only
operate the miter saw work stand on a hard,
flat, and level surface. DO NOT set up the 7. LOCK WORK SUPPORTS. Tighten lock knobs
miter saw work stand on a soft surface, such
as sand or mud.
to secure the work supports before using the
miter saw work stand.
4. MITER SAW WORK STAND USAGE. Only use 8. EXPERIENCING DIFFICULTIES. If at any time
the miter saw work stand to support a miter
saw. This stand is NOT intended for use as a
ladder or scaffolding.
you are experiencing difficulties performing
the intended operation, stop using this stand!
Contact Tech Support at (360) 734-3482 for
help.
COPYRIGHT © JULY, 2010 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#13127TR
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
D4041 Miter Saw Stand Instructions
7. Slide the roller assemblies into the crossbars and
secure them with the M8-1.25 x 20 knobs (see Figure
4).
8. Loosen the T-track lock knobs and adjust the T-tracks
to the width of your miter saw, then slide the heads
of two M8-1.25 x 50 hex bolts into each T-track.
T-Track
9. Place the miter saw over the bolts, and secure each
location with one washer and two hex nuts (see
Figure 5); when securing these, tighten the top hex
nut against the bottom one so they do not work loose
from the vibrations that occur while cutting.
T-Track
Lock Knob
Figure 5. Mounting the miter saw.
Adjusting Work Stand Extension Arms
1. Slide the extension arms out to their maximum reach
and place a straight 2x4 across the miter saw table
and rollers.
2. Loosen the crossbar knobs and rotate the roller
assemblies until the rollers almost touch the 2x4, as
shown in Figure 6. Then loosen the roller assembly
lock knobs, slide the rollers up to touch the 2x4, and
re-tighten the lock knobs.
Figure 6. Adjusting the support rollers.
Folding Miter Saw Stand for Storage
1. Remove the support braces, retract the extension
arms and rotate the support rollers flat.
2. Push in the locking pins shown in Figure 7 and fold
the legs up into the stand.
Locking Pin
Figure 7. Folding the miter saw stand.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
D4041 Miter Saw Stand Instructions
D4041 Parts
12
14
13
15
1
2
11
3
4
17
16
9
5
6
10
18
33
7
8
32
19
21
22
20
23
34
24
30
31
25
29
28
27
26
REF PART #
1
2
DESCRIPTION
XD4041001 ROLLER
XD4041002 SUPPORT
REF PART #
DESCRIPTION
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
XD4041018 SMALL AXLE
XD4041019 RIGHT LEG
XD4041020 FOOT
XD4041021 T-TRACK LOCKING PLATE
XD4041022 BIG AXLE
XD4041023 LEFT LEG
XPB71M
XD4041025 WHEEL BRACKET
XPW03M
XPN01M
3
4
XD4041003 END PLUG
XD4041004 BUSHING
5
6
XD4041005 OUTSIDE GEAR
XD4041006 INSIDE GEAR
7
8
9
XD4041007 LOCK KNOB M8-1.25 X 20
XD4041008 ROLLER CROSSBAR
XD4041009 EXTENSION ARMS
HEX BOLT M6-1 X 45
FLAT WASHER 6MM
HEX NUT M6-1
10
11
12
13
14
15
16
17
XPB06M
XD4041011 STAND
XPN03M
XPWF08M
XPB166M
XD4041015 T-TRACK
XD4041016 COMPRESSION SPRING
XD4041017 PIN
HEX BOLT M8-1.25 X 12
XD4041028 WHEEL
HEX NUT M8-1.25
FENDER WASHER 8MM
HEX BOLT M8-1.25 X 50
XPB118M
XPLN04M
XPW01M
HEX BOLT M8-1.25 X 45
LOCK NUT M8-1.25
FLAT WASHER 8MM
XD4041032 LOCK KNOB M8-1.25 X 50
XPB03M HEX BOLT M8-1.25 X 16
XD4041034 SUPPORT BRACE
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
|