MODEL W1675
13" Portable Planer
INSTRUCTION MANUAL
COPYRIGHT © NOVEMBER, 2002 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in Taiwan
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
PAGE
INTRODUCTION ................................................................................2
About Your New Planer ..............................................................................2
Woodstock Service and Support....................................................................2
Warranty and Returns................................................................................3
Specifications ..........................................................................................3
SAFETY FIRST..................................................................................4
Standard Safety Instructions ....................................................................4-5
ADDITIONAL SAFETY INSTRUCTIONS FOR PLANERS....................................6
Avoiding Potential Injuries ........................................................................7
ELECTRICAL....................................................................................8
110V Operation........................................................................................8
Extension Cords........................................................................................8
Grounding ..............................................................................................8
ASSEMBLY ......................................................................................9
Unpacking ..............................................................................................9
Box Contents ..........................................................................................9
Shop Preparation ......................................................................................9
Cleaning Machine ....................................................................................10
Beginning ..............................................................................................10
Mounting ..............................................................................................11
Handwheel ............................................................................................12
Dust Port ..............................................................................................12
ADJUSTMENTS ..............................................................................13
Controls................................................................................................13
Turning / Changing Knives ........................................................................14
Extension Tables ....................................................................................17
OPERATIONS..................................................................................18
Starting the Planer ..................................................................................18
Basic Operations ....................................................................................19
Troubleshooting......................................................................................21
MAINTENANCE................................................................................22
Lubrication............................................................................................22
General ................................................................................................22
Brush Replacement..................................................................................22
Table and Base ......................................................................................22
CLOSURE ......................................................................................23
Parts Breakdown and Parts List ..............................................................24-27
Your Notes ............................................................................................28
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
-1-
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
About Your New Planer
Your new SHOP FOX® Planer has been specially designed to provide many years of trouble-free service.
Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable
operation.
The Model W1675 is a great portable planer that packs an impressive punch for its size. Unlike most
planers of similar size, the Model W1675 takes stock to a maximum width of 13" which further expands
your planing capabilities. The Model W1675 has many features and gives excellent planing results and
years of service.
Woodstock International, Inc. is committed to customer satisfaction in providing this manual. It is our
intent to make sure all the information necessary for safety, ease of assembly, practical use and
durability of this product be included.
If you should have any comments regarding this manual, please feel free to contact us at:
Woodstock International, Inc.
Attn: Technical Department
P.O. Box 2309
Bellingham, WA 98227
Woodstock Service and Support
We stand behind our machines! In the event that a defect is found, parts are missing or questions arise
about your machine, please contact Woodstock International Service and Support at 1-360-734-3482 or
send e-mail to: [email protected]. Our knowledgeable staff will help you troubleshoot problems,
send out parts or arrange warranty returns.
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Returns
Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from
workmanship and materials for a period of 2 years from the date of original purchase by the original
owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence
or accidents, lack of maintenance, or to repairs or alterations made or specifically authorized by anyone
other than Woodstock International, Inc.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX®
machine or machine part which in normal use has proven to be defective, provided that the original
owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair
facility designated by our Bellingham, WA office, with proof of their purchase of the product within 2
years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect
through inspection. If it is determined there is no defect, or that the defect resulted from causes not
within the scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost
of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies with
the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this
warranty exceed the purchase price paid for the product, and any legal actions brought against
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall in
no event be liable for death, injuries to persons or property or for incidental, contingent, special or
consequential damages arising from the use of our products.
Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durability
standards. We reserve the right to change specifications at any time because of our commitment to
continuously improve the quality of our products.
Specifications
Motor Size ..................................................................2 HP, 110V, Universal
Amperage Draw....................................................................................15
Maximum Width of Cut ..........................................................................13"
Maximum Depth of Cut at 13" Width ........................................................1⁄16"
Maximum Depth of Cut at 5" Width ..........................................................1⁄8
"
Maximum Cutting Height..........................................................................6"
Minimum Stock Length ............................................................................6"
Cutterhead ..............................................................2 Knife, 129⁄32" Diameter
Cutterhead Speed ........................................................................9000 RPM
Cuts Per Minute ..............................................................................18,000
Feed Rate ....................................................................................26 FPM
Machine Weight ..............................................................................93 lbs
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST!
READ MANUAL BEFORE OPERATING MACHINE.
FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL
RESULT IN PERSONAL INJURY.
Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury and/or damage to the machinery.
This symbol is used to alert the user to useful information about proper
operation of the equipment.
NOTICE
Standard Safety Instructions
1. Thoroughly read the instruction manual before operating your machine. Learn the applications,
limitations and potential hazards of this machine. Keep manual in a safe, convenient place for future
reference.
2. Keep work area clean and well lighted. Clutter and inadequate lighting invite potential hazards.
3. Ground all tools. If a machine is equipped with a three-prong plug, it must be plugged into a three-
hole grounded electrical outlet or grounded extension cord. If using an adapter to aid in
accommodating a two-hole receptacle, ground using a screw to a known ground.
4. Wear eye protection at all times. Use safety glasses with side shields or safety goggles that meet
the national safety standards, while operating this machine.
5. Avoid dangerous environments. Do not operate this machine in wet or open flame environments.
Airborne dust particles could cause an explosion and severe fire hazard.
6. Ensure all guards are securely in place and in working condition.
7. Make sure switch is in the “OFF” position before connecting power to machine.
8. Keep work area clean, free of clutter, grease, etc.
9. Keep children and visitors away. Visitors should be kept a safe distance away while operating unit.
10.Childproof workshop with padlocks, master switches or by removing starter keys.
11.Disconnect machine when cleaning, adjusting or servicing.
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
12.Do not force tool. The machine will do a safer and better job at the rate for which it was designed.
13.Use correct tool. Do not force machine or attachment to do a job for which it was not designed.
14.Wear proper apparel. Do not wear loose clothing, neck ties, gloves, jewelry, keep long hair tied up,
etc.
15.Remove adjusting keys and wrenches. Before turning the machine on, make it a habit to check that
all adjusting keys and wrenches have been removed.
16.Use proper extension cord. Examine the
extension cord to ensure it is in good
Extension Cord Requirements
TABLE 1
condition. Use TABLE 1 to determine the
correct length and gauge of extension cord
needed for your particular needs. The amp
rating of the motor can be found on its
nameplate. If the motor is dual voltage, be
sure to use the amp rating for the voltage
you will be using. If you use an extension
cord with an undersized gauge or one that is
too long, excessive heat will be generated
within the circuit increasing the chance of a
fire or damage to the circuit. Always use an
extension cord that uses a ground pin and
connected ground wire. Immediately replace
a damaged extension cord.
Length and Gauge
Amp Rating
0-6
25ft
#18
#18
#16
#14
#12
#10
50ft 100ft
#16 #16
#16 #14
#16 #14
#12 #12
#12 #10
7-10
11-12
13-16
17-20
21-30
#10
No
17.Keep proper footing and balance at all times.
18.Do not leave machine unattended. Wait until it comes to a complete stop before leaving the area.
19.Perform machine maintenance and care. Follow lubrication and accessory attachment instructions
in the manual.
20.Keep machine away from open flame.
Operating machines near pilot lights and/or
open flames creates a high risk if dust is
Always wear safety glasses or goggles when
dispersed in the area. Dust particles and an
operating equipment. Operating this
ignition source may cause an explosion. Do
equipment creates the potential for flying
not operate the machine in high-risk areas,
debris that can cause eye injury. Everyday
including but not limited to, those
glasses or reading glasses only have impact
mentioned above.
resistant lenses, they are not safety glasses.
Be certain the safety glasses you wear meet
the appropriate standards of the American
National Standards Institute (ANSI).
21.If at any time you are experiencing
difficulties performing the intended
operation, stop using the machine! Then
contact our service department or ask a
qualified expert how the operation should
be performed.
22. Habits—good and bad—are hard to break.
Develop good habits in your shop and safety
will become second-nature to you.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL SAFETY INSTRUCTIONS FOR PLANERS
Read and understand this
entire instruction manual
before using this machine.
Serious personal injury
may occur if safety and
operational information is
Use this and other machinery with caution
and respect and always consider safety
first, as it applies to your individual working
conditions. Remember, no list of safety
guidelines can be complete and every shop
environment is different. Failure to follow
guidelines can result in serious personal
injury, damage to equipment and/or poor
work results.
MODEL W1675
13" Portable Planer
INSTRUCTION MANUAL
On-Line Technical Support: [email protected]
Phone: 1-360-734-3482
•
not
understood
and
COPYRIGHT
©
July, 2002 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in Taiwan
followed. Do not risk your
safety by not reading!
1. ALWAYS make sure the planer is on firm ground and is stable before operating. Immediately fix or
shim the planer if it rocks or wobbles.
2. ALWAYS inspect the workpiece before running it through the planer. Do not plane stock with loose
knots, nails, staples, dirt or other foreign objects. Always reject the wood or correct the problems
with the wood before planing.
3. ALWAYS make sure that all components of the planer are adjusted to their proper specifications
before planing stock.
4. ALWAYS use the help of another person or some type of support fixture when planing long stock.
5. ALWAYS stand clear of the workpiece when you are feeding it into the planer; otherwise, the
workpiece could possibly kick back and hit you or bystanders.
6. ALWAYS operate the planer with sharp and undamaged knives to achieve safe operation and quality
planing results.
7. ALWAYS plane wood, never plane any material other than wood like particle board, MDF, or other
wood products that are not natural wood grain. This planer is designed for wood only.
8. ALWAYS plane with multiple light cuts rather than excessively deep cuts.
9. ALWAYS wear hearing and eye protection and a dust mask when operating the planer.
10. NEVER attempt to free a stalled workpiece while the planer is powered on and plugged in.
11. ABSOLUTELY NEVER reach inside the planer or open the top cover while the planer is powered on
and/or plugged in.
12. NEVER plane wood that is less than 6" long or less than 1⁄4" thick.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
AVOIDING POTENTIAL INJURIES
Figure 1. DO NOT place hands inside planer
Figure 2. Feed wood by hand only until planer
when operating.
feed roller begins to pull wood inside planer.
Figure 4. Stand out of the way of the workpiece
line of travel.
Figure 3. DO NOT stand directly behind
workpiece line of travel.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
110V Operation
Grounding
The SHOP FOX® W1675 is prewired for 110
volts. The 2 HP motor draws approximately 15
amps. Choose an outlet with 15 amp circuit
breaker or fuse protection. Remember circuits
being used by other machines at the same time
add to the total electrical load being applied by
this machine. Add up the amperage load ratings
of all machines on the circuit. If this total
amperage load exceeds the amperage rating of
the circuit breaker or fuse, use a different
circuit with a higher amperage rating.
Any electrical outlet and
circuit that you plug your
machine into must be
grounded. Serious injury
and/or fire may occur if this
warning is ignored!
Ground this machine! The electrical cord
supplied with the Model W1675 comes with a
grounding pin. Do not remove the pin if your
outlet does not accept a ground pin, see Figure
5. Have the outlet box replaced by a qualified
electrician or have an appropriate adapter
installed.
DO NOT modify an existing low-amperage circuit
by only replacing the circuit breaker with a
breaker rated for a higher amperage. The
breaker and the complete circuit must be
replaced by a qualified electrician.
NOTICE
Make sure when using an adapter, the adapter
is grounded.
Extension Cords
Remember, an adapter with a grounding wire
does not guarantee the machine will be
grounded. A ground source must always be
verified in the electrical circuit within the wall
or conduit.
Using extension cords with an undersized gauge
or one that is too long, generates heat in the
cord that may cause fire or circuit damage. If
you must use an extension cord, use the
guidelines below and TABLE 2 to determine the
correct cord length and gauge. The amp rating
of the motor is 15 amps and can be found on its
nameplate.
•Use a cord rated for Hard Service (Grade S)
•Use a cord that is 100 feet or less only
•Use a cord with a ground wire and pin
•Use only undamaged cords
Extension Cord Requirements
TABLE 2
Length and Gauge
Amp Rating
0-6
25ft
#18
#18
#16
#14
#12
#10
50ft 100ft
#16 #16
#16 #14
#16 #14
#12 #12
#12 #10
7-10
Figure 5. Never remove grounding pin.
11-12
13-16
17-20
21-30
#10
No
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Unpacking
Shop Preparation
Get assistance before
Always make sure that all
entrances to your shop are
locked or that machines
are equipped with safety
lock-out devices to protect
curious children or visitors
from serious injury. Never
allow unsupervised people
in your shop who have not
been fully trained!
starting assembly. The
Model W1675 Planer is a
heavy load at 93 pounds.
The planer is carefully packed. However, if it is
damaged or is missing any parts, please contact
Woodstock International Service and Support at
1-360-734-3482 or send e-mail to:
•
•
Planer Location: Make sure that where
ever you operate the planer, you face the
planer toward an area where if a work piece
should be projected, bystanders will not be
struck with the workpiece. Take all
necessary safety precautions.
Box Contents
Layout and inventory the parts shipped with
your Planer. See Figure 6. This will help with
machine assembly.
Item
Qty.
Working Clearances: Consider your existing
and anticipated needs, size of material to
be processed through each machine, and
space for auxiliary stands, work tables or
other machinery when establishing a
location for your planer.
Planer Unit
Handwheel
1
1
2
1
1
1
1
3
Magnets
T-Handle Allen® Wrench
Allen® Screw
Flat/Lock Washer
Dust Port
•
•
Lighting: Make sure the lighting is bright
enough to eliminate shadows and prevent
eye strain.
Phillips® Screws
Outlets: Electrical circuits must be
dedicated and/or large enough to handle
the amperage requirements of the
machinery. Electrical outlets should be
located near each machine so power or
extension cords are clear of high-traffic
areas. Observe local electrical codes for
proper installation of new lighting, outlets
or circuits and read and understand this
manual.
Planer
Dust Port
Phillips®
Screw
T-Handle
Allen
Flat/Lock
Washers
Wrench
Allen®
Screw
Magnets
Handwheel
Figure 6. Planer components removed from the
box and laid out for identification.
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Beginning
Although the main components of the SHOP
FOX® W1675 are assembled at the factory,
some assembly is required. The following series
of instructions are the recommended sequence
for final assembly.
Cleaning Machine
The Model W1675 table and other unpainted
parts are coated with a waxy grease for
corrosion protection. For the best machine
performance, clean all moving parts and
coated surfaces. Remove this grease with a
solvent cleaner or a citrus-based degreaser. Do
not use chlorine-based solvents—if you splash
these solvents onto a painted surface, you will
ruin painted and plastic finishes.
All tools required for assembly have been
included with the planer except standard-head
and Phillips®-head screwdrivers.
Before cleaning the machine, read and
understand the following Warnings and Caution:
Keep
your
machine
unplugged during any
assembly, adjustments, or
maintenance procedures.
Ignoring this warning may
result in serious personal
injury!
Never use flammables
such as gas or other
petroleum-based solvents
to clean your machine.
These products have low
flash points and present
the risk of explosion and
severe personal injury!
Never smoke while using
cleaning solvents. Smoking
may cause explosion or
risk of fire when exposed
to these products!
Most solvents used to
clean machinery are
toxic when inhaled or
ingested. When using
these products, work in
a well ventilated area
and keep away from any
potential
ignition
sources (pilot lights).
Always dispose of any
waste rags in a sealed
container to make sure
they do not cause fire or
environmental hazards.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting
For proper results and safe use, the Model
W1675 must be mounted to a sturdy workbench
or a stand like the SHOP FOX® Tool Stand
shown in Figure 7. Mounting hardware is not
included.
To mount the planer do these steps:
1. Determine the length of mounting bolts you
will need by adding the thickness of your
mounting surface and the base of the
planer.
Figure 7. SHOP FOX® Tool Stand.
2. With the help of an assistant set the planer
in the desired position on the mounting
Get assistance before
starting assembly. The
Model W1675 Planer is a
heavy load at 93 pounds.
surface. See Figure 8.
3. Use a pencil to mark the positions of the
mounting holes from the base of the planer.
1
4. Drill a ⁄2" hole into your mounting surface
in each of these positions.
Figure 8. Planer in mounted position.
5. Secure the planer with the mounting
hardware. Figure 9 shows the proper order
of the mounting hardware placement.
1
6. Insert a ⁄2" diameter bolt, two flat washers
(1 for top, 1 for bottom), and thread on a
lock washer (for behind nut), and a hex nut
to secure the planer at each corner.
Planer Base
NOTICE
DO NOT over tighten the bolts as damage to
the base will result.
Mountingꢀ
Surface
Figure 9. Hardware mounting assembly.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Handwheel Handle
Roll Pin
To mount the handwheel to the planer do
these steps:
Handwheel
Shaft
1. If not already done, insert the roll pin into
the shaft protruding from the front of the
planer. See Figure 10.
2. Slide the handwheel onto the shaft and
align the handwheel with the roll pin.
3. Slide the lock washer on the Allen® screw
first and then the flat washer.
4. Thread the Allen® screw into the end of the
shaft to secure the handwheel to the shaft
as shown in Figure 11.
Figure 10. Insert the roll pin into shaft.
5. Use the T-handle Allen® wrench and tighten
Handwheel
the screw.
Dust Port
To mount the dust port do these steps:
Shaft
Allen® Screw
and
Washers
1. Position the dust port onto the chip
deflector at back of the planer.
2. Thread and tighten the three Phillips®
screws. Figure 12 shows the dust port
correctly installed on the planer.
Figure 11. Handwheel mounted to the shaft.
Dust Port
Screws
Figure 12. Dust port mounted to planer.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
Controls
Keep
your
machine
Familiarize yourself with the controls of your
new planer. They will be frequently mentioned
throughout the instructions in this manual, and
the better you know your machine, the better
you can make it perform. Use Figure 13 and
Figure 14 to locate the planer controls.
unplugged during any
assembly, adjustments, or
maintenance procedures.
Ignoring this warning may
result in serious personal
injury!
•
Height Handwheel — Allows you to adjust
the head up or down to accommodate the
workpiece height and control cutting depth.
The wheel also has a turn vs. cutting depth
guide. See Figure 13.
Height
Head Lock Lever
Handwheel
•
•
Head Lock — Allows you to lock the head in
place so that the cutter height setting will
not move after adjustment.
Height
Scale
See Figure 13.
Depth Gauge — Shows you the current
depth of cut to be made on the workpiece.
Only works when the workpiece is directly
under the gauge. See Figure 13.
Depth
Gauge
Depth Stop
•
•
Height Scale — Shows you the current
cutterhead height adjustment.
See Figure 13.
Figure 13. Machine controls.
Depth Stop — Allows you to lock the
cutterhead to a set depth so the cutterhead
lowest setting does not change when
planing many boards. The cutterhead can
be returned to the minimum setting quickly
after planing thicker wood.
Reset Button
Safety Lockout Key
See Figure 13.
•
•
Reset Button — Allows you to reset the
planer if the thermal overload shuts the
machine down. Only resets after the
machine has cooled down. See Figure 14.
ON/OFF
Paddle Switch
Safety Lockout Key — Allows you to protect
the machine from accidental startup.
Remove the key to disable the ON/OFF
Paddle Switch, reinsert the key to enable
the switch. See Figure 14.
Figure 14. Electrical controls.
•
ON/OFF Paddle Switch — Allows you to
toggle the planer power ON or OFF. Pull the
switch up to turn the planer ON. Push the
switch down to turn the planer OFF.
See Figure 14.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning/Changing
Knives
The Model W1675 features a 2 knife, quick
change cutterhead system with double-sided,
disposable knives. The knives have been
installed at the factory and no adjustments are
needed prior to using the planer.
Do not grab the cutterhead
for any reason and be very
careful working around the
cutterhead. The knives are
extremely
sharp
and
severe injury may occur!
As your planer gets used, the knives will need to
be routinely inspected, turned around, and
eventually replaced. After both sides are dull,
install new knives.
Dust Port
Keep
your
machine
unplugged during any
assembly, adjustments, or
maintenance procedures.
Ignoring this warning may
result in serious personal
injury!
Screws
Figure 15. Remove the screws and dust port.
To remove the knives do these steps:
1. Unplug the planer!
Chip Deflector
2. Use a Phillips® screwdriver and remove the
three screws that secure the dust port to
the planer, and remove the dust port. See
Figure 15.
Screws
Figure 16. Remove the screws and chip deflector.
Wear heavy leather gloves when working with
or near the cutterhead and planer knives. The
knives are dangerously sharp and serious
injury may occur.
Side Cover Not
Shown For Clarity
Cutterhead
Pulley
3. Use the T-handle Allen® wrench and remove
the two screws, and remove the chip
deflector as shown in Figure 16.
4. Rotate the cutterhead pulley from the
underside of the planer until the lock lever
secures the cutterhead into position. See
Figure 17.
Figure 17. Rotate the cutterhead pulley until locked.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
Allen® Screw
Wear heavy leather gloves when working with
or near the cutterhead and planer knives. The
knives are dangerously sharp and serious
injury may occur.
5. Use the T-handle Allen® wrench that is
included with the planer to remove the six
screws from the knife locking plate. See
Figure 18.
Figure 18. Remove six screws from the knife
6. Use the included magnets to lift the locking
plate from the cutterhead and out of the
planer. See Figure 19.
binder.
7. Use the magnets to lift the knife from the
the cutterhead and out of the planer. See
Figure 20.
8. Carefully clean and inspect the cutterhead
with a rag and inspect for the following:
• Make sure the threaded screw holes
contain no wood material or sawdust.
• Make sure that the hex socket and the
threads of all Allen® screws are in good
condition. Replace if questionable.
Figure 19. Lift out the locking plate with the
magnets.
• Make sure any resin or glue build-up on
the cutterhead is removed so the knife
will sit flat on the cutterhead.
• Make sure any resin or glue build-up on
the knife is removed so the knife will sit
flat on the cutterhead if you reuse the
knife.
• Make sure the knife is free of cracks. If
any cracks exist replace both knives.
Figure 20. Lift out the knife with the magnets.
NOTICE
To maintain accurate and consistent planing
results, Woodstock International Inc. does
not recommend sharpening the knives.
Replace the knives when they get dull.
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
Wear heavy leather gloves when working with
or near the cutterhead and planer knives. The
knives are dangerously sharp and serious
injury may occur.
Do not grab the cutterhead
for any reason and be very
careful working around the
cutterhead. The knives are
extremely
sharp
and
To install or turn the knives do these steps:
1. Unplug the planer.
severe injury may occur!
2. Turn the knife to expose the unused blade
or replace it if both blades are dull.
3. Set the magnets on the knife, so the
beveled edge is facing you. See Figure 21.
Beveled Edge
4. Use the magnets to lower and seat the knife
onto the cutterhead, and make sure the
guides fit into the holes and the knife sits
flat on the cutterhead. See Figure 22.
5. Use the magnets to lower and seat the knife
binder onto the knife.
Figure 21. Position the magnets and blade taper.
NOTICE
Cutterhead
Uneven tightening of the knife binder
retaining screws may cause the cutterhead
and the knives to vibrate, wear
prematurely, and produce poor planing
results!
Guide Pin
Knife
6. Use the T-handle Allen® wrench and thread
all six screws into the the cutterhead until
they just contact the knife binder. DO NOT
tighten the screws yet.
7. Use the T-handle Allen® wrench and lightly
tighten the screws into place, starting from
the center and alternating back and forth
toward the ends. Repeat this tightening
sequence twice until all are snug. DO NOT
over tighten.
Figure 22. Position the knife on the cutterhead.
Push Lever
This Direction
8. Press the lock lever and rotate the
cutterhead pulley until the cutterhead locks
into position. See Figure 23.
Very Sharp
Cutterhead
9. Repeat all knife removal and installation
steps on the remaining knife.
Lock Lever
10. Make sure all knife binder screws are tight.
11. Reinstall the chip deflector and the dust
Figure 23. Push the cutterhead lock lever.
port that was previously removed.
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
Extension Tables
The extension tables have been set at the
factory and require no adjustments upon initial
operation. However, over the life of the planer,
it is possible for the extensions to become
misaligned with the main table and to need
slight adjustment.
Table Gap of 0.008" to 0.010"
Keep
your
machine
No Roller Gap
unplugged during any
assembly, adjustments, or
maintenance procedures.
Ignoring this warning may
result in serious personal
injury!
(Either Roller)
Figure 24. Check extension tables with a
straightedge. The rollers on the ends of the
tables should be even with the main table.
To check extension table alignment do these
steps:
Table Shown
Flipped Up
1. Unplug the planer!
2. Place a good quality, steel straightedge
across both extension table rollers and the
main table. The straightedge should be
perfectly flat across the main table with a
clearance of 0.008" to 0.010" measured with
a feeler gauge, and the straight edge should
evenly touch the rollers on the ends of the
extension tables as shown in Figure 24.
Adjustment Bolt
and Jam Nut
3. If the rollers on the extension tables are not
even or the straight edge does not have the
correct gap with the main table, then the
extensions need to be adjusted.
Figure 25. One of four extension table
adjustment bolts.
4. With the straightedge still in place, use the
adjustment bolts shown in Figure 25 to
raise/lower the extension table.
5. Back off the adjustment-bolt jam nut (both
sides of the planer) and raise/lower the
extension table so there is no gap at the
table rollers and an 0.008" to 0.010" gap at
the main table under the straight edge.
6. Snug the adjustment bolts and double-check
your setting. If the alignment is correct,
then hold each bolt in position, and
completely tighten the jam nut.
7. Repeat steps 1 through 6 for the other
extension table roller.
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
Starting the Planer
Once assembly is complete and adjustments
have been made, the machine is ready for a test
run. The purpose of a test run is to identify any
unusual noises and vibrations, as well as to
confirm the machine is performing as intended.
Always wear a dust mask
and safety glasses when
operating this machine.
ON/OFF
Paddle Switch
Sawdust
allergic
may
reactions
cause
or
Figure 26. Toggle the paddle switch for startup
respiratory problems.
and shutdown.
Make sure loose clothing
and long hair is secured
and kept away from
moving parts.
To test run the planer do these steps:
1. Flip the paddle switch up to turn the planer
ON. See Figure 26.
2. Poise your finger over the paddle switch for
emergency shut down if there is a problem.
See Figure 27.
Figure 27. Position your finger over the paddle
switch for emergency shutdown.
3. Listen for any unusual noises or vibrations,
if unusual noise or vibration exists, shut the
planer OFF immediately.
4. Unplug the planer and remove the safety
lockout key. DO NOT make any adjustments
while it is plugged in. See Figure 28.
5. Investigate the source of the noise or
vibration. DO NOT start the planer again
until the problem is corrected. Contact
Woodstock International Service and
Support at 1-360-734-3482 or send e-mail
to: [email protected].
6. Repeat steps 1 through 5 until the planer
runs smoothly.
Figure 28. Remove the safety lockout key.
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
DO NOT operate this planer until you read and
understand this entire manual first. If you have
any questions contact Woodstock International.
Always wear a dust mask
and safety glasses when
operating this machine.
Sawdust
allergic
may
reactions or
cause
respiratory problems.
Figure 29. Only plane clean stock.
Make sure loose clothing
and long hair is secured
and kept away from
moving parts.
To select and prepare the wood:
1. Choose clean wood only. See Figure 29.
Scrape off all glue from joined boards
before planing. Remove all dirt, nails,
staples, and imbedded gravel, etc. A hidden
nail in the wood will instantly damage the
sharp edges of the knives and cause
unsatisfactory results in all future planning
operations. Plane only natural wood fiber.
Never plane wood composites such as
particle board, plywood or MFD. Never
plane laminates, formica, or other
synthetic materials.
Portion
Removed With
Jointer
Figure 30. Face joint the concave side of cupped
stock before planing.
3. Carefully inspect the wood you will feed
into the planer. Each board must have at
least one flat surface to slide along the
planer table. To create a flat surface, pass
the wood over a jointer first. See Figure
30. Some defects such as moderate
twisting, loose knots or severe cracks may
make the stock unplanable.
2. Choose dry wood only. DO NOT plane wet
wood or wood with a high moisture content.
Wood that has been exposed to rain or snow
and has more than a 20% moisture content,
will plane poorly, dull the knives, and wear-
out the motor. Excess moisture may cause
rust and corrosion problems. Plane only KD
(kiln-dried) wood and AD (air-dried) wood,
which is correctly dried with no surface
moisture. Never plane PAD (partially-air-
dried) wood or you will have poor planing
results.
NOTICE
Inspect all lumber completely and remove
all foreign material. Wood that has been
stored on concrete floors is often imbedded
with fine grit and small stones that will
damage the knives.
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
PLANER SETUP:
DO NOT plane wood that is shorter than six
inches.
1. Use roller stands or roller tables to support
and maintain alignment of long sections of
wood while it enters and exits the planer,
and make sure your work area is clear.
2. Position the wood on the infeed side of the
planer extension table so the cutterhead
will cut WITH the grain. Look at the grain
pattern on the side of the board. If the arc
of the cutterhead knife will follow the same
lines in the grain pattern, you will be
cutting WITH the grain. If the arc of the
cutterhead knife will cross the grain pattern
lines, then you will be cutting AGAINST the
grain. DO NOT cut against the grain and,
DO NOT feed end cut or end-grained wood
in to the planer.
Figure 31. Notice that operator is feeding
workpiece from the infeed side and has his
body positioned to the side of the travel path.
3. Unlock the head lock lever.
4. Measure the wood and turn the height
handwheel to make a very light first cut
about 1/32" or less, so if there is any bulges
in the wood the cutterhead will not jam and
stall. Subsequent cuts can be made at a
deeper setting depending on the width of
the wood, but plan on taking multiple cuts
before you can achieve a completely flat
surface.
Figure 32. DO NOT stand in the path of the
planer outfeed because you can be hit with
the workpiece.
5. Lock the head lock lever to save your
cutterhead depth adjustment. For multiple
surfacing, set and lock the depth stop also
to maintain a particular cutterhead
adjustment. The depth stop is a quick way
to set the lowest height setting for planing
many boards, but allows you to quickly
return the cutterhead to the depth stop
setting after having to adjust the
3. Support the ends of the wood and turn the
planer on.
4. Keeping your hands clear of the cutterhead,
slowly and evenly push the wood into the
planer until the planer feed roller draws the
wood in, and then remove your hands from
the area. DO NOT force the wood into the
planer as you will dull the knives and
overload the motor.
cutterhead to
a
higher setting to
compensate for varying heights of wood.
PLANING WOOD:
5. When the planing is complete, repeat all
1. Put your safety glasses, dust mask, and
steps for additional wood.
hearing protection on.
6. When you are done with the planer, turn
the machine off and remove the safety
lockout key.
2. Position yourself out of the way of the path
of the wood as shown in Figure 31.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
FUZZY GRAIN — Grain fibers stand up on the
Troubleshooting
Planing Results
workpiece after planing.
SOLUTIONS:
• Do not surface damp or wet wood, check
it with a moisture meter. Anything over
20% should be allowed to dry.
• Install sharp knives.
Planing results are affected by the species and
condition of the wood, how the planer is setup,
and the condition of the knives. The following
characteristics are some common problems and
the solutions woodworkers might have while
planing.
GLOSSY SURFACE — The wood is scorched,
blackened, and/or glossy.
SOLUTIONS:
SNIPE — More material is being removed from
• Remove all resin or glue build-up on the
rollers and the cutterhead, and surface
acceptable wood.
• Install sharp knives so shallow cuts do not
have to be made to compensate for dull
knives that burn the wood. If this is the
case and the condition has existed for a
long time, the knives may be damaged as
a result and cannot be turned. The knives
must be replaced.
board ends rather than the middle of the board.
SOLUTIONS:
• Provide more support on the infeed and
outfeed sides so the wood travels
completely through the planer without
any vertical tilting. This alignment
problem occurs with all planers to some
degree.
• Hold the workpiece flat against the
planer tables and rollers so the board
does not tilt while entering and exiting
the planer.
• If knives are sharp and a glossy surface
still results, increase the cutting depth.
• Install extra roller stands.
• Raise the table/ lift the board ends.
THERMAL SWITCH POPS — The planer motor
overheats and shuts off automatically.
SOLUTIONS:
• Push the reset button in when the planer
completely cools down.
CHIP MARKS — Chips are not being properly
expelled from the cutterhead. The chips get
caught between the knives and the workpiece
and hinder knife cutting ability. Chip marks
usually appear as random and uneven.
• Make shallower cuts.
• Remove all resin or glue build-up on the
rollers and the cutterhead. Often resin or
glue build-up can over-heat the planer by
decreasing the cutter sharpness while
increasing drag in the feed mechanism.
• Install sharp knives.
SOLUTIONS:
• Unclog the chip deflector blockage and
correct for cause of blockage.
• Increase cleaning intervals.
• Install a dust collector.
• Surface acceptable stock.
CHIPPED GRAIN — Grain shows cut marks and
chips.
WOOD DOES NOT FEED CORRECTLY — The
planer draws wood in erratically or slowly.
SOLUTIONS:
• Do not plane against the grain.
• Do not plane wood with knots or cross
grain.
SOLUTIONS:
• Plane wood that is not twisted or warped
• Remove any pitch build-up on the feed
rollers.
• Use sharp knives.
• Make shallower cuts.
• Surface acceptable stock.
• Turn or replace the knives if they are
dull or broken.
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Lubrication
General
Since all bearings are shielded and permanently
lubricated, simply leave them alone until they
need to be replaced. Do not lubricate them.
To ensure best performance of your Model
W1675, complete regular periodic maintenance.
Make it a habit to inspect your machine each
time you use it. Check for the following
conditions and repair or replace when
necessary.
For other items on this machine and before
occasionally applying lubricant, wipe the
machine clean. Then apply a thin coat of light
machine oil.
•
•
•
•
•
•
Loose mounting bolts.
Worn switch.
Excess buildup of sawdust.
Worn or damaged cords and plugs.
Worn or damaged drive belt.
Any other condition that could hamper the
safe operation of this machine.
Remember your goal is to achieve corrosion
protection. Too much lubrication will attract
dirt and sawdust, which can damage your
machine and cause parts to bind or stick.
Brush Replacement
Keep
your
machine
unplugged during any
assembly, adjustments, or
maintenance procedures.
Ignoring this warning may
result in serious personal
injury!
Brush Cover
Figure 33. Remove the brush cover.
To replace the carbon brush do these steps:
1. Unplug the planer!
2. Use a flat-head screwdriver and remove the
brush cover. See Figure 33.
3. Carefully slide out the spring and carbon
brush. See Figure 34.
4. Insert the new carbon brush exactly like the
old one was installed.
5. Replace cover.
6. Repeat steps 1 through 5 for the other
motor brush on the other side of the motor.
Table and Base
Figure 34. Remove/Install the motor brush.
Keep tables rust-free with regular applications
of products like SLIPIT®. For long term storage,
consider using products like Boeshield T-9™.
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
CLOSURE
The following pages contain parts diagrams/lists
We recommend you keep this manual for
complete information regarding Woodstock
International, Inc.’s warranty and return policy.
Should a problem arise, we recommend that you
keep your proof of purchase with your manual.
If you need additional technical information
relating to this machine, or if you need general
assistance or replacement parts, please contact
the Service Department at 1-360-734-3482 or e-
mail: [email protected].
and a warranty card for your SHOP FOX® Model
W1675.
If you need parts or help in assembling your
machine, or if you need operational
information, we encourage you to call our
Service Department. Our trained service
technicians will be glad to help you.
If you have comments dealing specifically with
this manual, please write to us using the address
in the General Information. The specifications,
drawings, and photographs illustrated in this
manual represent the Model W1675 as supplied
when the manual was prepared. However, due
to Woodstock International, Inc.’s policy of
continuous improvement, changes may be made
at any time with no obligation on the part of
Woodstock International, Inc. Whenever
possible, though, we send manual updates to all
owners of a particular tool or machine that have
registered their purchase with our warranty
card. Should you receive one, add the new
information to this manual and keep it for
reference.
Additional information sources are necessary to
realize the full potential of this machine. Trade
journals, woodworking magazines, and your
local library are good places to start.
The Model W1675 is specifically designed for
PLANING operations. DO NOT MODIFY AND/OR
USE THIS MACHINE FOR ANY OTHER PURPOSE.
MODIFICATIONS OR IMPROPER USE OF THIS
TOOL WILL VOID THE WARRANTY. If you are
confused about any aspect of this machine, DO
NOT use it until all your questions have been
answered.
We have included some important safety
measures that are essential to this machine’s
operation. While most safety measures are
generally universal, we remind you that each
workshop is different and safety rules should be
considered as they apply to your specific
situation.
Always wear safety glasses or goggles when
operating equipment. Operating this
equipment creates the potential for flying
debris that can cause eye injury. Everyday
glasses or reading glasses only have impact
resistant lenses, they are not safety glasses.
Be certain the safety glasses you wear meet
the appropriate standards of the American
National Standards Institute (ANSI).
Use this machine with respect and caution
to lessen the possibility of mechanical
damage or operator injury. As with all
power tools, there is danger associated
with the Model W1675. If normal safety
precautions are overlooked or ignored,
injury to the operator or others in the area
is likely.
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
1
2
3
4
5
6
7
8
9
10 XPW02M
11 XPW04M
12 XPSB14M
13 X1675013 MOTOR
64 XPN03M
65 XPSB78M
66 X1675066 TENSION WHEEL ASSEMBLY
67 X1675067 PIN
68 X1675068 BUSHING
69 X1675069 GEAR
70 X1675070 GEAR
HEX NUT M8-1.25
CAP SCREW M5-0.8 X 35
71 XPK64M
KEY 4 X 4 X 7MM
72 X1675072 GEAR CASE ASSEMBLY
73 X1675073 GEAR
22 X1675022 KNIFE
23 X1675023 KNIFE BINDER
24 X1675024 CHAIN COVER
25 X1675025 SIDE COVER
26 X1675026 SPECIAL PIVOT SCREW
27 X1675027 SPRING
74 XPW03M
FLAT WASHER 6MM
75 X1675075 POINTER
76 XPN01M
77 XPSB28M
HEX NUT M6-1.0
CAP SCREW M6-1.0 X 15
78 X1675078 CHAIN
79 X1675079 HANDLE 1.5 X 24MM
28 XPSB78M
29 XPR05M
CAP SCREW M5-0.8 X 40
EXT RETAINING RING 15MM
80 XPRP39M
ROLL PIN 4 X 20MM
30 X1675030 SPROCKET
81 X1675081 POINTER
82 X1675082 BUSHING
83 X1675083 SHAFT
31 XPR03M
32 XPK64M
33 X1675033 SHAFT
EXT RETAINING RING12MM
KEY 5 X 5 X 9MM
84 X1675084 THICKNESS GAUGE
85 X1675085 SPRING
86 X1675086 KNOB M6-1.0 X 17
87 X1675087 SPRING
34 X1675034 GEAR BOX COVER
35 X1675035 BUSHING
36 X1675036 GEAR 44T
37 X1675037 GEAR 58T
38 X1675038 BUSHING
39 X1675039 HANDWHEEL
40 X1675040 SHAFT
88 XPSB06M
CAP SCREW M6-1.0 X 25
89 X1675089 SPRING
90 X1675090 ROLLER BRACKET
91 XP6203
BEARING 6203
41 XP6202
BEARING 6202
92 X1675092 COLLAR
42 X1675042 CHAIN
43 X1675043 PLATE
93 X1675093 BELT 135 X 6MM
94 X1675094 CUTTERHEAD PULLEY
95 X1675095 SPECIAL NUT M14-1.5
96 X1675096 BRACKET
44 XPSB04M
CAP SCREW M6-1.0 X 10
45 X1675045 BRACKET
46 X1675046 SPRING
97 X1675097 RUBBER ROLLER
98 X1675098 SPRING
99 X1675099 COLUMN
47 XPS09M
48 X1675048 STABLE PLATE
49 XPS09M
PHLP HD SCREW M5-0.8 X10
PHLP HD SCREW M5-0.8 X10
50 X1675050 BELT GUARD
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
123 X1675123 TOOLING TRAY
124 X1675124 “T” ALLEN WRENCH 4MM
125 X1675125 KNIFE SETTING GAUGE
126 XPTLW02M EXT-TOOTH WASHER 5MM
127 X1675127 SPRING
100 X1675100 SHORT LEAD SCREW
101 X1675101 WING (LEFT)
102 X1675102 PLATE
103 X1675103 GEAR
104 XPR01M
EXT RETAINING RING 10MM
128 X1675128 CAPTURED SCR M8-1.25 X 20/8
129 X1675129 GEAR
130 X1675130 SPROCKET
131 XPSS01M
SET SCREW M6-1 X 10
132 XPLWO4M LOCK WASHER 8MM
133 XPW03M
134 XPW01M
FLAT WASHER 6MM
FLAT WASHER 8MM
135 X1675135 MOTOR BRUSH
136 X1675136 BRUSH CAP
137 X1675137 LABEL(SCALE)
138 X1675138 LABEL (DEPTH SCALE)
139 X1675139 LABEL (SHOP FOX®)
140 X1675140 LABEL (DEPTH SCALE)
141 X1675141 LABEL (WARNING)
142 X1675142 LABEL (13" PLANER)
115 XPSB18M
CAP SCREW M4-07 X 8
116 X1675116 WING (RIGHT)
117 X1675117 EXTENSION WING
118 X1675118 SPECIAL FLAT WASHER 6MM
119 XPSB28M
120 X1675120 BUSHING
CAP SOCKET SCREW M6-1.0 X 15MM
143 XPS09M
PHLP HD SCREW M5-0.8 X 10
144 X1675144 DUST PORT
121 X1675121 ROLLER
122 X1675122 LEAD SCREW (RIGHT)
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
YOUR NOTES
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
YOUR NOTES
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
YOUR NOTES
-30-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name __________________________________________________________________________________________
Street __________________________________________________________________________________________
City ____________________________________________________________________State________Zip_________
Phone Number_______________________E-Mail_________________________________FAX___________________
MODEL #______________________________ Serial #___________________________________________________
The following information is given on a voluntary basis and is strictly confidential.
1.
2.
Where did you purchase your SHOP FOX® machine?
10.
What stationary woodworking tools do you own? Check all that apply.
_________________________________________________________
___Air Compressor
___Band Saw
___Panel Saw
___Planer
How did you first learn about us?
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Spindle Sander
___Table Saw
___Drum Sander
___Dust Collector
___Horizontal Boring Machine
___Jointer
___Advertisement
___Friend
___Mail order Catalog
___World Wide Web Site
___Local Store
___Lathe
___Mortiser
___Vacuum Veneer Press
___Wide Belt Sander
___Other__________________________________________________
Which of the following magazines do you subscribe to.
___Other__________________________________________________
3.
11.
12.
13.
Which benchtop tools do you own? Check all that apply.
___American Woodworker
___Cabinetmaker
___Today’s Homeowner
___Wood
___1" x 42" Belt Sander
___5" - 8" Drill Press
___8" Table Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Mini Jointer
___6" - 8" Grinder
___Mini Lathe
___10" - 12" Thickness Planer
___Scroll Saw
___Spindle/Belt Sander
___Family Handyman
___Fine Homebuilding
___Fine Woodworking
___Home Handyman
___Wooden Boat
___Woodshop News
___Woodsmith
___Woodwork
___Journal of Light Construction
___Old House Journal
___Popular Mechanics
___Popular Science
___Woodworker
___Woodworker’s Journal
___Workbench
___Other__________________________________________________
___American How-To
Which portable/hand held power tools do you own? Check all that apply.
___Popular Woodworking
___Other__________________________________________________
Which of the following woodworking/remodeling shows do you watch?
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Miter Saw
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
4.
5.
6.
___Backyard America
___Home Time
___The New Yankee Workshop
___This Old House
___The American Woodworker
___Woodwright’s Shop
___Other__________________________________________________
___Other__________________________________________________
What machines/supplies would you like to see?
What is your annual household income?
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
14.
15.
16.
What new accessories would you like Woodstock International to carry?
_________________________________________________________
_________________________________________________________
What is your age group?
Do you think your purchase represents good value?
___20-29
___30-39
___40-49
___50-59
___60-69
___70 +
___Yes
Would you recommend SHOP FOX® products to a friend?
___Yes ___No
___No
7.
8.
9.
How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
17.
Comments:________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
How would you rank your woodworking skills?
___Simple
___Advanced
___Master Craftsman
___Intermediate
How many SHOP FOX® machines do you own? _____________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL, INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|