Woodstock Impact Driver W1701 User Manual

Model W1701

¾ HP SHAPER

MANUAL UPDATE

This update covers changes made to the owner's manual after it was printed. Keep this update with your

owner's manual for future reference. Before operating your new machine, you MUST read and understand

this insert and the entire Model W1701 manual to reduce the risk of injury from improper use or setup. If

you have questions, contact Tech Support at (360) 734-3482 or by email at [email protected].

What has changed?

The inventory has changed to reflect an improved tool set now included with the Model W1701. All page

references made on this insert refer to the pages in the original Model W1701 manual.

Removed Inventory

Additional Inventory Breakdown &

Refer to Inventory List on Page 9. These items

Parts List

are no longer included with the machine.

Use this breakdown and parts list together with

those on Pages 27–29.

D. Special 26mm Flat Wrench ..................1

E. Wrench Set (8mm, 14mm, 30mm)..........1

Additional Inventory (Figure 1)

The following items are now included with the

Model W1701.

�

��

�

��

�

V. Combo Wrench 8/10mm......................1

W. Combo Wrench 12/14mm ....................1

X. Combo Wrench 27/30mm ....................1

��

REF PART�#

155 XPWR810

156 XPWR1214

157 X1701157

158 X1701158

DESCRIPTION

COMBO�WRENCH�8/10MM

WRENCH�12�X�14

WRENCH�27/30MM

FLAT�WRENCH�27MM

�

Figure 1. Additional inventory.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT

THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

#10453JB

Printed in China

Download from Www.Somanuals.com. All Manuals Search And Download.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

INTRODUCTION..................................................................................................2

Woodstock Technical Support............................................................................ 2

Specifications............................................................................................... 2

SAFETY............................................................................................................3

Standard Safety Instructions ............................................................................. 3

Additional Safety Instructions for Shapers............................................................. 5

Avoiding Potential Injuries ............................................................................... 6

ELECTRICAL......................................................................................................7

110V Operation............................................................................................. 7

Extension Cords ............................................................................................ 7

Grounding ................................................................................................... 7

SET UP ............................................................................................................8

Unpacking ................................................................................................... 8

Inventory .................................................................................................... 8

Inventory List ............................................................................................... 9

Machine Placement ........................................................................................ 9

Cleaning Machine .......................................................................................... 9

Assembly....................................................................................................10

Test Run ....................................................................................................11

OPERATIONS ................................................................................................... 12

General .....................................................................................................12

Cutters vs. Router Bits ...................................................................................12

Spindle Elevation..........................................................................................13

Spindle Direction..........................................................................................13

Fence Positioning .........................................................................................14

Fence Alignment ..........................................................................................14

Table Inserts ...............................................................................................14

Cutter Installation ........................................................................................15

Router Bit Installation....................................................................................17

Straight Shaping...........................................................................................18

Templates ..................................................................................................19

Freehand Shaping .........................................................................................20

MAINTENANCE ................................................................................................. 21

General .....................................................................................................21

Table & Base...............................................................................................21

Lubrication .................................................................................................21

Maintenance Schedule....................................................................................21

SERVICE......................................................................................................... 22

General .....................................................................................................22

Belt Adjustment...........................................................................................22

Table Spacer Kit...........................................................................................23

Spindle Cartridge Replacement.........................................................................24

Resurfacing Fence.........................................................................................25

Electrical Components & Wiring........................................................................26

PARTS ........................................................................................................... 27

Parts List ...................................................................................................28

USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

INTRODUCTION

Woodstock Technical Support

We stand behind our machines! In the event that questions arise about your machine, parts are miss-

ing, or a defect is found, please contact Woodstock International Technical Support at (360) 734-3482 or

send e-mail to: [email protected]. Our knowledgeable staff will help you troubleshoot prob-

lems and send out parts for warranty claims.

If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.

If you have comments about this manual, please contact us at:

Woodstock International, Inc.

Attn: Technical Documentation Manager

P.O. Box 2309

Bellingham, WA 98227

Specifications

Motor Size ...................................................... 1HP, 110V, 60 Hz Single-Phase

Motor Speed..............................................................................3,450 RPM

Amps.................................................................................................13

Spindle Size .......................................................................................¹⁄2

Spindle Max Cutter Height W/Bushings, Nuts, and Rub Collar ......................... 2¹⁄2

Maximum Cutter Diameter.................................................................... 2⁷⁄8

Spindle Travel.....................................................................................⁷⁄8

Spindle Speed.......................................................................... 13,200 RPM

Table Size ....................................................................24" Wide x 19" Deep

Stand .........................................................................Powder Coated Paint

Footprint................................................................18⁷⁄8" Wide x 16⁵⁄8" Deep

Dust Port..........................................................................................N/A

Power Transfer .......................................................................... Belt Drive

Bearings.................................Shielded and Permanently Lubricated Ball Bearings

Switch ...............................................................Forward and Reverse Toggle

Machine Weight............................................................................. 200 lbs.

-2-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

SAFETY

READ MANUAL BEFORE OPERATING MACHINE.

FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL

RESULT IN PERSONAL INJURY.

Indicates an imminently hazardous situation which, if not avoided, WILL

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, COULD

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, MAY

result in minor or moderate injury.

This symbol is used to alert the user to useful information about proper

operation of the equipment, and/or a situation that may cause damage

to the machinery.

NOTICE

Standard Safety Instructions

1. READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents serious

injury hazards to untrained users.

2. ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eye-

glasses only have impact resistant lenses—they are NOT safety glasses.

3. ALWAYS WEAR AN NIOSH APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES

DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses.

4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause

permanent hearing damage.

5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may

get caught in moving parts. Wear protective hair covering to contain long hair and wear non-slip

footwear.

6. NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.

Be mentally alert at all times when running machinery.

7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make

sure operation instructions are safe and clearly understood.

8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work

area.

9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys.

-3-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power off and allow all moving parts to come to

a complete stop before leaving machine unattended.

11. DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or

where any flammable or noxious fumes may exist.

12. KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents.

13. USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE. Undersized cords over-

heat and lose power. Replace extension cords if they become damaged. DO NOT use extension cords

for 220V machinery.

14. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SERVICING MACHINERY. Make sure switch is

in OFF position before reconnecting.

15. MAINTAIN MACHINERY WITH CARE. Keep blades sharp and clean for best and safest performance.

Follow instructions for lubricating and changing accessories.

16. MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY.

17. REMOVE ADJUSTING KEYS AND WRENCHES. Make a habit of checking for keys and adjusting

wrenches before turning machinery ON.

18. CHECK FOR DAMAGED PARTS BEFORE USING MACHINERY. Check for binding and alignment of

parts, broken parts, part mounting, loose bolts, and any other conditions that may affect machine

operation. Repair or replace damaged parts.

19. USE RECOMMENDED ACCESSORIES. Refer to the instruction manual for recommended accessories.

The use of improper accessories may cause risk of injury.

20. DO NOT FORCE MACHINERY. Work at the speed for which the machine or accessory was designed.

21. SECURE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. A secured

workpiece protects your hands and frees both hands to operate the machine.

22. DO NOT OVERREACH. Keep proper footing and balance at all times.

23. MANY MACHINES WILL EJECT THE WORKPIECE TOWARD THE OPERATOR. Know and avoid condi-

tions that cause the workpiece to "kickback."

24. ALWAYS LOCK MOBILE BASES (IF USED) BEFORE OPERATING MACHINERY.

25. BE AWARE THAT CERTAIN DUST MAY BE HAZARDOUS to the respiratory systems of people and

animals, especially fine dust. Make sure you know the hazards associated with the type of dust you

will be exposed to and always wear a respirator approved for that type of dust.

-4-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Additional Safety Instructions for Shapers

READ and understand this

entire instruction manual

before using this machine.

Serious personal injury

may occur if safety and

operational information

is not understood and

followed. DONOTriskyour

safety by not reading!

USE this and other machinery with caution

and respect, and always consider safety

first, as it applies to your individual working

conditions. Remember, no list of safety

guidelines can be complete, and every shop

environment is different. Failure to follow

guidelines can result in serious personal

injury, damage to equipment and/or poor

work results.

1. KEEPING HANDS SAFE: Never pass your hands near or directly over or in front of the cutter. As

one hand approaches the 12-inch radius point, move it in an arc motion away from the cutter to

the outfeed side and reposition that hand more than 12 inches beyond the cutter.

2. HOLDING AND UNSAFE WORKPIECE: DO NOT shape stock shorter than 12 inches without special

fixtures or jigs. Where practical, shape longer stock and cut to size.

3. CUTTER POSITIONING: Keep the cutters on the underside of the workpiece whenever possible to

reduce operator exposure to the moving cutter.

4. TESTING FOR CLEARANCE: Unplug the shaper, and always rotate the spindle by hand to test any

new setup to ensure proper cutter clearance before starting the shaper.

5. SAFELY STARTING AND FEEDING WORKPIECE: When shaping contoured work and using a rub

collar, NEVER start shaping at a corner. See the rub collar section further on in the manual. The

danger of kick-back is increased when the stock has knots, holes, or foreign objects in it.

6. PREPARING A WORKPIECE: Always run warped stock through a jointer before you run it through

the shaper. An warped workpiece is difficult to process, which increases the risk of an accident.

7. CUTTER EXPOSURE: Keep any unused portion of the cutter below the table surface.

8. AVOIDING AN OVERLOAD: Never attempt to remove too much material in one pass. Several light

passes are safer and give a cleaner finish.

9. SAFELY FEEDING A WORKPIECE: In most applications it is advisable to use a push stick as a

safety device; in others it can be quite dangerous. If the push stick comes in contact with

the cutter on the end grain, it can be violently propelled from your hand—potentially causing

serious injury. We recommend using some type of fixture, jig, or hold-down device as a safer

alternative. And ALWAYS use a guard or other type of protective device at all times.

10. AVOIDING CUTTER AND WORKPIECE GRAB: Always make sure cutter is positioned in the correct

direction before starting shaper, and always feed against the rotation of the cutter.

11. SAFELY USING ALTERNATE TABLE CONFIGURATIONS: Always use overhead guard when the

fence is not in place. The overhead guard reduces the risk of contacting the cutterhead.

12. SAFE CUTTER INSTALLATION: Never operate the shaper without verifying that the spindle nut is

tight. A tight spindle nut reduces the risk of the cutter or rub collars flying off during operation.

-5-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Avoiding Potential Injuries

NOTE: Guard Removed for Clarity. Always Use Guard.

Figure 1. Use a SHOP FOX^®Featherboard as

Figure 4. Use SHOP FOX^®BOARD BUDDIES^®for

anti-kick back protection.

holding down the workpiece.

NOTE: Guard Removed for Clarity. Always Use Guard.

Figure 2. Use rubberized SHOP FOX^®Push

Blocks to grip the workpiece when cutting.

Figure 5. Use a SHOP FOX^®Right Angle Jig

when making special cuts without a safety guard.

NOTE: Guard Removed for Clarity. Always Use Guard.

Figure 3. Use the smallest insert the cutter will

allow to keep woodchips away from the inside of

shaper.

Figure 6. Unplug the shaper whenever making

adjustments or changing cutters.

-6-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

ELECTRICAL

110V Operation

The SHOP FOX^®Model W1701 is prewired for 110 volt

operation. The motor supplied with your new Machine

Type is rated at 1 HP and will draw approximately 13

amps. A 5-15 plug is included for your machine and is

intended to be plugged into a matching 5-15 receptacle.

Connect your machine to a circuit (wire, breaker, plug,

receptacle) that is rated for at least 15 amps.

We recommend connecting this machine to a dedicated

circuit with a verified ground, using the circuit breaker

size given below. Never replace a circuit breaker with one

of higher amperage without consulting a qualified electri-

cian to ensure compliance with wiring codes.

Figure 7. Typical 110V 3-prong plug and

outlet.

If you are unsure about the wiring codes in your area or

you plan to connect your machine to a shared circuit,

you may create a fire hazard—consult a qualified elec-

trician to reduce this risk.

This equipment must be grounded.

Verify that any existing electrical out-

let and circuit you intend to plug into

is actually grounded. If it is not, it will

be necessary to run a separate 12 AWG

copper grounding wire from the outlet

to a known ground. Under no circum-

stances should the grounding pin be

removed from any three-pronged plug

or serious injury may occur.

Extension Cords

When it is necessary to use an extension cord, use the

following guidelines:

•

Use cords rated for Standard Service

Never exceed a length of 100 feet

Use cords with 12 ga. wire or bigger

Ensure cord has a ground wire and pin

Do not use cords in need of repair

Grounding

This machine must be grounded! The electrical cord sup-

plied with this machine comes with a grounding pin. Do

not remove it. If your outlet does not accommodate a

ground pin, have it replaced by a qualified electrician or

have an appropriate adapter installed.

Note: When using an adapter, the adapter must be

grounded.

-7-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

SET UP

If any parts are missing, examine the pack-

aging for the missing parts. For any missing

parts, find the part number in the back

of this manual and contact Woodstock

International, Inc. at (360) 734-3482 or at

[email protected]

Unpacking

The SHOP FOX^®Model W1701 has been carefully pack-

aged for safe transporting. If you notice the machine has

been damaged, please contact your authorized SHOP

FOX^®dealer immediately.

Inventory

LIFTING HAZARD!

Get help lifting and mov-

ing the heavy components

of this shaper.

The following is a description of the main components

shipped with the SHOP FOX^®Model W1701. Lay the

components out to inventory them.

Note: Some parts and hardware may already be installed

on the machine. make sure to check the machine when

you use the inventory list.

Figure 8. Component layout.

-8-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Machine Placement

Inventory List

•

Machine Mobility: Use the Model D2057

SHOP FOX^®Heavy-Duty Mobile Base so

you can make the most out of your shop

space by moving the Model W1701 1HP

Shaper out of the way when not in use.

Contact your SHOP FOX^®Dealer for price

and availability.

The following is a description of the main com-

ponents shipped with the SHOP FOX^®Model

W1701. Lay the components out to inventory

them, and refer to the list below and Figure 8.

Main Contents

Qty

A. Shaper Unit.....................................1

B. Stand Bolt Bag .................................1

— Carriage Bolts ⁵⁄16"-18 x ¹⁄2" ............ 16

— Flat Washers ³⁄8".......................... 16

— Hex Nuts ⁵⁄16"-18.......................... 16

C. Stand Side Panels..............................2

D. Fence Assembly................................1

E. Table Inserts 1-3/8", 1-3/4" .................1

D. Special 26mm Flat Wrench ..................1

F. Wrenches 8, 14, 23, 26, 30mm .........1 Ea

G. Router Bit Collets 1/4", 1/2" & Nut ....1 Ea

H. Fence Faces ....................................2

I. Guard............................................1

J. Fence Lock Studs 5/16"-20...................2

K. Guard Mounting Post..........................1

L. Guard Attachment Bar........................1

M. Miter Gauge Assembly ........................1

N. Tie Bars .........................................2

O. Knob and Fence Bolt Bag.....................1

— Star Knobs M8-1.25.........................2

— Large Dia. Flat Washers 8mm ............2

— Hex Bolts M8-1.25 x 12 ....................2

— Phillips Head Screws M8-1.25 x 20.......4

— Flat Washers 8mm..........................6

— Phillips Head Screws M4-.7 x 10 .........2

— Hex Nuts M4-.7..............................2

P. Table Spacer Kit...............................1

— Hex Bolt M12-1.75 x 30....................2

— Hex Bolt M12-1.75 x 40....................5

— Lock Washer 12mm.........................7

— Spacer 1/2" ..................................7

•

Working Clearances: Consider your

current and future shop needs with respect

to the machinery and the lumber to be

shaped. Allow enough space for safe

lumber support as the lumber is fed into

the shaper and as it exits the machine.

Outlets: Make sure the electrical circuits

have the capacity to handle the amperage

requirements for your Model W1701 1HP

Shaper. Electrical outlets should be

located near the shaper, so power or

extension cords are clear of high-traffic

areas.

Cleaning Machine

The table and other unpainted parts of your

machine type are coated with a waxy grease

that protects them from corrosion during ship-

ment. Clean this grease off with a solvent clean-

er or citrus-based degreaser. DO NOT use chlo-

rine-based solvents such as brake parts cleaner

or acetone—if you happen to splash some onto a

painted surface, you will ruin the finish.

ALWAYS work in well-

ventilated areas far from

possible ignition sources

when using solvents to

clean machinery. Many

solvents are toxic when

inhaled or ingested. Use

care when disposing

of waste rags and

towels to be sure they

DO NOT create fire or

environmental hazards.

-9-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Assembly

LACERATION HAZARD!

Inspect edges of all metal parts

before handling them. Some metal

parts may have sharp edges, which

can cause injury.

To assemble the shaper, do these steps:

1. Lay one stand side on the ground and attach the

cross bars with the 8mm carriage bolts, ³⁄8" washers,

and 8mm hex nuts as shown in Figure 9. DO NOT

fully tighten the nuts and bolts at this time.

Figure 9. Attaching cross bars to stand

side.

2. Attach the second stand side to the assembly.

Note: At this point, the assembly will be somewhat

wobbly. Have an assistant hold the assembly in

place while you attach the nuts and bolts.

3. Place the shaper table upside down on two sturdy

blocks that are at least 3¹⁄2" off the ground as shown

in Figure 10. Make sure the spindle DOES NOT touch

the ground or the weight of the shaper may damage

the spindle.

4. Place the stand assembly on the shaper and attach it

with the 8mm carriage bolts, ³⁄8" washers, and 8mm

hex nuts as shown in Figure 10.

Figure 10. Attaching stand to shaper unit.

5. Have an assistant help you turn the shaper unit over.

6. Level the shaper, then tighten all of the assembly

bolts on the stand.

NOTE: Sheet steel will often “spring” after it has been

fabricated at the factory, occasionally making it difficult

to line up precisely with other parts without a bit of

effort. Do not be surprised if the stand requires a bit of

“persuasion” to fit together. On the other hand, if the

parts just do not seem to work together, try switching

parts around (such as the tie bars).

7. Using the 5/16"-20 x 3/4" Phillips head screws, and

5/16" washers, install each fence facing to the fence

mount brackets as shown in Figure 11.

Figure 11. Installing fence facing.

-10-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

8. For custom fence facing, make sure the screw heads

are countersunk completely below the surface of the

fence face.

Safety

Guard Bar

Safety

Guard

9. Connect the safety guard bar to the safety guard

shaft with two M8-1.25 x 12 bolts and the 8mm flat

washers. See Figure 12.

10. Connect the safety guard to the safety guard bar

with two M4-0.7 x 12 Phillips^®head screws and the

M4-0.7 nuts. See Figure 12.

Fence

Housing

Safety Guard

Shaft

Figure 12. Guard and fence assembly.

11. Position the extension bar and safety guard on the

main fence housing and install the T-lock handle.

See Figure 12.

Hold Spindle

Here

12. Position the guard as close as possible to the spin-

dle/cutter without impeding the feeding path of the

workpiece.

13. Place an 8mm open-end wrench on top the spindle

(see Figure 13).

14. Using a 14mm open-end wrench on the drawbar nut,

(Figure 14), make sure the drawbar nut is tight, but

DO NOT over-tighten the drawbar nut.

Figure 13. Wrench location on spindle.

Note: This is an important safety measure that

must be done before the Test Run on the next

page.

Taper

Test Run

Complete this process once you have familiarized yourself

with all instructions in this manual.

To test run the shaper, do these steps:

1. Read the entire instruction manual first, so you

are familiar with all controls and functions of the

shaper!

Figure 14. Threading on drawbar nut with

the tapered end up.

2. Connect your machine to the power source.

3. Turn the shaper ON. The shaper should run smoothly

with little or no vibration.

— Immediately turn the jointer OFF if you suspect

any problems, and fix those problems before start-

ing the shaper again. If the source of an unusual

noise or vibration is not readily apparent, contact

our technical support for help at (360) 734-3482 or

Projectiles thrown from the machine

could cause serious eye injury. Wear

safety glasses during the test run!

-11-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

OPERATIONS

General

This machine will perform many types of operations

that are beyond the scope of this manual. Many of these

operations can be dangerous or deadly if performed incor-

rectly.

The instructions in this section are written with the under-

standing that the operator has the necessary knowledge

and skills to operate this machine. If at any time you

are experiencing difficulties performing any operation,

stop using the machine!

READ and understand this entire instruc-

tion manual before using this machine.

Serious personal injury may occur if

safety and operational information is not

understood and followed. DO NOT risk

your safety by not reading!

If you are an inexperienced operator, we strongly recom-

mend that you read books, trade articles, or seek train-

ing from an experienced operator before performing any

unfamiliar operations. Above all, your safety should

come first!

Cutters vs. Router Bits

When shipped, the Model W1701 is setup for using shaper

cutters. However, if you plan on using router bits, you

must first convert the Model W1701 to a router table. To

convert your shaper to a router table, refer to Page 23.

Always wear safety glasses when oper-

ating this machine. Failure to comply

may result in serious personal injury.

If you're not sure which type of cutting equipment you will

use, read below for the pros and cons of both.

Shaper Cutters

Pros—Shaper cutters are larger, more durable and gener-

ally last longer than router bits. If you plan on cutting

many linear feet of a certain profile, then shaper cutters

are the best choice.

Cons—Shaper cutters are much more expensive than rout-

er bits and they are typically too large for small projects.

Router Bits

DO NOT investigate problems or adjust

the Machine Name while it is running.

Wait until the machine is turned OFF,

unplugged and all working parts

have come to a complete stop before

proceeding!

Pros—Router bits are cheaper than shaper cutters and

come in a wider range of profiles and sizes. If you plan

on making small projects that do not require many linear

feet of cutting, then router bits are the best choice.

Cons—Router bits are not as durable as shaper cutters,

and they are typically designed to be operated faster

than this machine can operate.

-12-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Spindle Elevation

Correct spindle height is crucial to most shaping applica-

tions. Use a piece of test wood to confirm the correct

spindle height before cutting expensive lumber.

To set the spindle height, do these steps:

1. Loosen the spindle lock knob located on the side of

the shaper as shown in Figure 15.

2. Move the spindle height lever shown in Figure 16 to

raise the spindle or left to lower the spindle.

3. Retighten the spindle lock knob on the side of the

shaper. DO NOT over-tighten the knob. Only a small

amount of tension is needed to keep the spindle

from moving during operation.

Figure 15. Spindle lock knob.

Spindle Direction

The Model W1701 is capable of operating in two

directions by use of the forward and reverse switch

shown in Figure 17.

It is very important that the workpiece be fed against

the direction of the cutter rotation. This will prevent a

climb cut and maintains a safe cutting procedure for the

operator.

Most operations are done with the switch in the FWD

position. However, there will be times when it is

necessary to flip the shaper cutter over and run the

spindle in the opposite direction (REV).

Figure 16. Spindle-height lever.

•

When the switch is pointing to the FWD position, the

spindle and cutter rotate counterclockwise.

•

When pointing to the REV position, the spindle and

cutter rotate clockwise.

CUTTER CONTACT HAZARD!

Feeding the workpiece in the same

direction that the cutter is rotating

may result in a climb cut, which

can pull your hand into the cutter.

Always feed the workpiece AGAINST

the direction that the cutter is

rotating to reduce this risk.

Figure 17. Forward and reverse switch.

-13-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Fence Positioning

The two fence faces are independently adjustable to

allow for different shaping tasks. The fence faces can be

set at different positions to remove material from the

entire edge of the wood stock or set at the same position

to shape part of the edge.

To adjust the fence, do these steps:

1. Loosen the fence mount lock handle shown in Figure

18.

2. Adjust the position of the fence by turning the

adjustment knob shown in Figure 18.

3. Once the fence is in the desired position, tighten

Figure 18. Fence mount lock handle and

down the fence mount lock handle.

adjustment knob.

Fence Alignment

Before shaping, check that the two fence faces are paral-

lel.

To align the fences so they are parallel with each

other, do these steps:

1. Get a quality straightedge that is long enough to

span the entire length of the fence assembly.

2. Adjust the fence faces so they are in as close to the

same parallel position as possible.

Figure 19. Use straightedge to check

3. Hold the straightedge across both of the fence faces

as shown in Figure 19.

fence.

4. If the fence faces are not parallel, place shims

between the back of the fence face and the face of

the fence mount. With some trial and error shim

adjusting, parallel fence faces can be achieved.

Table Inserts

Two inserts (Figure 20) are provided allowing for three

different opening sizes to be achieved. Use the smallest-

size opening for a cutter to reduce wood chips falling into

the machine. Using the smallest-size opening also covers

any unused portion of the bit below the surface of the

table, thus reducing the chance of operator injury.

Figure 20. Using table insert to keep

wood shavings on the table.

-14-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Cutter Installation

��

ACCIDENTAL START-UP HAZARD!

Always disconnect machine

before installing or removing any

cutting equipment. Performing

these procedures while machine

is connected to power greatly

increases risk of serious injury!

Figure 21. Rub collar mounted above

cutter.

CUTTER FLY-APART HAZARD!

Using cutters rated lower than the spindle speed greatly

increases the risk that the cutter will fly apart during

operation, which may cause very serious injury to the

operator and bystanders.

��

Before installing cutters, you must plan the configuration

of rub collars and cutters required for the intended

application.

Figure 22. Rub collar mounted between

two cutters.

Rub collars limit the depth of cut and are typically used

with most cutters, depending on the profile and type of

cut being performed.

��

There are three set up positions for rub collars:

•

ABOVE THE CUTTER as shown in Figure 21. This

setup is the safest and produces the most consistent

results.

��

BETWEEN TWO CUTTERS as shown in Figure 22. This

setup has the advantage of making two profile cuts

in a single pass.

Figure 23. Rub collar mounted below

cutter.

•

BELOW THE CUTTER as shown in Figure 23. This

setup allows the cut to be viewed by the operator;

however, it is also the most dangerous because the

operator is exposed to the moving cutter.

WE DO NOT RECOMMEND SHAPING WITH A RUB

COLLAR BELOW THE CUTTER!

-15-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

To install cutters and rub collars, do these steps:

1. DISCONNECT SHAPER FROM POWER SOURCE!

2. Slide the cutter(s) and rub collars onto the spindle in

the correct orientation for your intended cut.

Keyed

Safety

Washer

3. Install the keyed safety washer and nut as shown in

Figure 24.

CUTTER FLY-APART HAZARD!

Always use the keyed safety washer! The lock tang

on this washer prevents the shaper cutter bit from

loosening the spindle nut during operation.

Figure 24. Placing the keyed safety

washer.

4. Thread on and tighten down the spindle nut with the

provided 23mm wrench, while holding the spindle at

the top with an 8mm wrench, as shown in Figure 25.

5. Make sure the cutter rotates freely in the correct

direction needed for the cut (in most cases this is

the FWD direction on the FWD/REV switch, which is

counterclockwise on the spindle).

6. Install applicable safety guard(s).

AMPUTATION/LACERATION

HAZARD!

Figure 25. Tightening spindle nut.

Accidental contact with a cutter

during operation will remove parts

of fingers or large chunks of flesh.

Safety guards greatly reduce this

risk and must always be used when

operating this machine!

-16-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Router Bit Installation

Before using router bits, you should convert the shaper

to a router table. Refer to Table Spacer Kit on Page 23

to learn how to do this.

The Model W1701 comes with a ¹⁄2" and ¹⁄4" router bit

collet. When installing router bits, make sure that the

router bits are secure before starting the machine. A

loose router bit may fly out of the spindle.

To install the router bit collet, do these steps:

1. DISCONNECT SHAPER FROM POWER SOURCE!

2. Push the collet into the collet nut until the off-cen-

ter lip of the collet nut snaps into the collet groove.

See Figure 26.

Figure 26. Router bit collet in collet nut.

Note: This lip and groove pulls the collet from the

spindle when the collet nut is removed.

3. Place the collet nut and collet into the spindle. See

Figure 27.

4. Finger tighten the collet nut onto the spindle until it

is flush with the top of the collet nut.

5. Insert the router bit.

6. Using the 26mm special flat wrench, insert it under

the table and hold the spindle stationary (see Figure

28-A) while using the 30mm wrench to tighten the

collet securing the router bit (see Figure 28-B).

Figure 27. Installed collet flush with top

of collet nut.

Use 26mm Flat

Wrench Here

Figure 28. Installing a router bit.

-17-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Straight Shaping

Because the shaper fence is independently adjustable,

you can set up the shaper to cut part or all of the

workpiece edge.

To set the fence up for cutting material from the whole

edge of the workpiece, do these steps:

1. Loosen the locking handle shown in Figure 29.

2. Turn the adjustment knob located on the back of the

fence mount and adjust the infeed fence until the

workpiece contacts the cutter at the desired loca-

tion.

3. Tighten the lock handle to lock the fence into posi-

Figure 29. Fence controls.

tion.

4. Adjust the outfeed fence so that it is located as far

back from the front of the table as possible.

5. Turn the shaper ON.

6. Using a piece of scrap wood, advance the workpiece

8" into the cutters, and turn the machine OFF. DO

NOT remove the workpiece from the infeed fence

face.

7. Once the cutter has come to a complete stop, adjust

the outfeed fence so that it just touches the newly

cut edge as shown in Figure 30.

Figure 30. Fence setup for jointing-type

operations (Guard Not Shown For Clarity).

8. Make sure all fence lock handles are tight.

To set up the fence for partial edge removal, do these

steps:

1. Loosen the lock handle on the side of the fence

mount.

2. Turn the adjustment knob and adjust the infeed

fence until the workpiece contacts the cutter at the

desired location.

3. Tighten the lock handle to lock the fence into posi-

tion.

4. Adjust the outfeed fence so that it comes into align-

ment with the infeed fence as shown in Figure 31.

Figure 31. Fence setup for partial-edge

removal (Guard Removed For Clarity).

-18-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

5. Now place a straightedge against both faces of the

fence to check alignment. Once they are both in

alignment, make sure the lock handle is tightened.

Always feed the wood against the rotation of the cutter as

shown in Figure 32. Another way to conceptualize this is

to always feed the wood into the cutter so that the cutter

is pushing against the direction of feed. Never feed wood

in the same direction as the cutter rotation. This is called

a “climb cut” and is extremely dangerous.

Also, examine the grain on the side edge of the board.

Whenever possible, run the board so the shaper cutters

are cutting with the grain as shown in Figure 31. This will

minimize the chance of tear out.

Figure 32. Sequence for shaping an edge

around a workpiece

(Guard Removed For Clarity).

CUTTER CONTACT HAZARD!

Cutting small or narrow workpieces

greatly increases the risk of cutter

contact during operation. Use jigs

or holding devices when cutting to

reduce this risk.

Templates

The use of templates allows identical parts to be cut

with speed and accuracy. Shaping with a pattern begins

by attaching a prefabricated template to the rough

workpiece. The edge of the template rides against a rub

collar on the spindle as the cutter cuts the matching

profile on the workpiece edge as shown in Figure 33.

��

Template Construction Tips:

��

•

Make sure that screws or clamps will not come into

contact with the cutter.

•

Design the assembly so that cutting will occur under-

neath the workpiece.

Figure 33. Profile of a template being

•

Make handles for safety and control.

used.

Use materials that will move easily across the table

surface and rub collar.

•

Install hold-down clamps at three sides of the pat-

tern assembly or screw the pattern assembly to the

back side of the workpiece.

-19-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Freehand Shaping

Freehand shaping is shaping without the aid of the miter

slot or fence. The most dangerous part of shaping free-

hand is beginning the cut, where the cutter first contacts

the workpiece. Often the workpiece will tend to jerk or

kickback, catching the operator off guard.

To reduce kickbacks and maintain workpiece control when

freehand shaping, use a starting pin or starting block. The

pin/block allows you to maintain workpiece control by

anchoring and slowly pivoting the workpiece into the cut-

ter as the cut is started (see Figure 34).

Figure 34. Starting pin operation

(Guard not shown for clarity).

Freehand shaping often requires you to remove

the fence resulting in reduced protection from the

cutters. ALWAYS use an auxiliary jig and take extreme

care when shaping with the fence removed.

To set up the shaper for freehand shaping, do these

steps:

1. DISCONNECT SHAPER FROM POWER SOURCE!

2. Remove the fence assembly from the shaper.

3. Insert the starting pin in the best suited hole on the

table so you can feed the workpiece into and against

the rotation of the cutter.

Figure 35. Hold-down jig used to support

workpiece.

4. Install the cutter so it will cut in the correct direc-

tion, and adjust the spindle height.

5. Install the safety guard. DO NOT use the shaper

without a guard.

6. Use a supplemental hold-down jig like the SHOP

FOX^®W1500 Right Angle Jig shown in the

Accessories section, or you can use rubberized-han-

dle push blocks to support or guide the workpiece

and protect your hands.

7. Place the workpiece against the starting pin.

8. Slowly pivot and feed the workpiece into the cut-

ter. Avoid starting the cut on the corner of the

workpiece as kickback could occur. Once the cut is

started, the workpiece should be pulled away from

the starting pin.

Figure 36. A piece of wood clamped to

the table can serve as a starting block.

(Guard not shown for clarity).

-20-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

MAINTENANCE

General

Regular periodic maintenance on your Model W1701 1HP

Shaper will ensure its optimum performance. Make a

habit of inspecting your shaper each time you use it

Check for the following conditions and repair or

replace when necessary:

•

Loose mounting bolts.

Worn switch.

Worn or damaged cords and plugs.

Damaged drive belt.

Any other condition that could hamper the safe

operation of this machine.

MAKE SURE that your machine is

unplugged during all maintenance pro-

cedures! If this warning is ignored, seri-

ous personal injury may occur.

Table & Base

Maintenance

Cleaning the Model W1701 is relatively easy. Vacuum

excess wood chips and sawdust, and wipe off the remain-

ing dust with a dry cloth. If any resin has built up, use a

resin dissolving cleaner to remove it.

Schedule

Daily:

•

Vacuum all dust on and around the

machine.

Wipe down tables and all other

unpainted cast iron with a metal

protectant.

Protect the unpainted cast iron surfaces on the table

by wiping the table clean after every use—this ensures

moisture from wood dust does not remain on bare metal

surfaces.

•

Every Month:

Keep tables rust-free with regular applications of a qual-

ity metal protectant.

•

V-belt tension, damage, or wear.

Clean/vacuum dust buildup from

inside cabinet and off of motor.

Lubrication

Since all bearings are shielded and permanently

lubricated, simply leave them alone until they need to

be replaced. Do not lubricate them.

For other items on this machine, an occasional

application of light machine oil is all that is necessary.

Before applying lubricant, clean off sawdust.

Your goal is to achieve adequate lubrication. Too much

lubrication will attract dirt and sawdust. Various parts of

your machine could lose their freedom of movement as a

result.

-21-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

SERVICE

General

This section covers the most common service adjustments

or procedures that may need to be made during the life

of your machine.

If you require additional machine service not included

in this section, please contact Woodstock International

Technical Support at (360) 734-3482 or send e-mail to:

[email protected].

MAKE SURE that your machine is

unplugged during all service proce-

dures! If this warning is ignored, seri-

ous personal injury may occur.

Belt Adjustment

Your shaper uses a flat-type belt on two drum-style pul-

leys, to compensate for different belt positions as the

spindle height is adjusted.

To adjust belt, do these steps:

1. DISCONNECT SHAPER FROM POWER SOURCE!

2. Loosen the belt adjustment bolts as shown in Figure

37.

3. Slide the motor position to increase or decrease belt

tension, so the belt is snug with about 1/4" deflec-

tion when pressed lightly with your fingertips.

4. Tighten the belt adjustment bolts.

Figure 37. Adjusting belt tension.

-22-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Table Spacer Kit

The provided table spacer kit allows you to modify your

shaper for use as a router table by raising the table. A

higher table will allow you to make shallow cuts and uti-

lize the upper blade area of most router bits with stan-

dard-length shanks.

To install the table spacer kit, do these steps:

1. DISCONNECT SHAPER FROM POWER SOURCE!

2. Remove the spindle lock nut and any cutters or rub

collars installed on the spindle.

Figure 38. Removing taper nut from

drawbar.

3. Remove table from the shaper by undoing the seven

bolts that secure it in place.

4. Loosen and remove the taper nut (see Figure 38)

while holding the top of the spindle with a wrench.

5. Gently tap the bottom of the drawbar to knock the

spindle loose.

��

6. Remove the spindle/drawbar assembly from the

��

spindle cartridge.

7. Place the table spacers over the table mounting

holes on the shaper.

8. Place the table on the spacers and secure it to the

shaper with the hex bolts from the router table

spacer kit (see Figure 39).

9. Save the removed table bolts for when you need to

covert the Model W1701 back to use as a shaper.

10. Refer to Router Bit Installation on Page 17 for

��

instructions on installing the collets and router bits.

Figure 39. Installing table spacers.

-23-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Spindle Cartridge

Replacement

Should a bearing fail, your shaper will probably develop a

noticeable rumble, which will increase when the machine

is put under load. If allowed to get worse, overheating of

the journal containing the bad bearing could occur, which

may cause the bearing to seize and possibly damage other

parts of the machine.

Pulley Cover

Mounting Bolts

Rather than disassemble the spindle cartridge to

remove worn out bearings, Woodstock International

offers replacement spindle cartridge assemblies (Part#

X1701407) as whole units, which makes replacement very

simple. The procedure takes 15-20 minutes.

To replace the spindle cartridge assembly:

Figure 40. Location of pulley cover

1. DISCONNECT SHAPER FROM POWER SOURCE!

mounting bolts.

2. Remove the spindle and drawbar from the spindle

cartridge assembly. (Remove tapered drawbar nut

and tap the drawbar up to knock it loose.)

Pulley

3. Take off the spindle pulley cover by removing the

two mounting bolts shown in Figure 40.

4. Loosen the two motor mount bolts, slide the motor

forward, and remove the V-belt.

5. Loosen the spindle lock knob.

6. Remove the cartridge nut on the bottom of the spin-

Cartridge Nut

dle, as shown in Figure 41, and slide the pulley off.

Figure 41. Location of cartridge nut and

7. Hold your hand under the spindle cartridge and

remove the elevation handle by unthreading it coun-

terclockwise. The spindle cartridge should drop into

your hand.

pulley.

8. Install the new cartridge assembly in the reverse

order of removal.

-24-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Resurfacing Fence

The fence can be resurfaced or made flat with a jointer

to correct any warping. This procedure should only be

done if the fences will not align with each other after

careful adjustment or they are warped.

To resurface the fence, do these steps:

1. Make sure the fence face mounting screws are far

enough below the surface of the fence that they will

not contact the jointer knives during operation.

Note: New fence faces can easily be made out of

hard wood and resurfaced by using this same proce-

dure.

Figure 42. Resurfacing a shaper fence on a

jointer.

2. Align both fence faces as straight as possible, using

a straightedge or your jointer table as an alignment

guide.

3. Resurface the fences on the jointer, as shown in

Figure 42.

-25-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Electrical Components & Wiring

Motor

Cord

Ground

Power Cord

ON/OFF Switch

Motor & FWD/REV Switch

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

-26-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

PARTS

��

-27-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Parts List

REF PART�#

DESCRIPTION

REF PART�#

DESCRIPTION

301

302

303

304

305

306

307

308

309

310

311

312

313

314

315

316

317

318

319

320

321

322

323

324

325

326

327

328

329

330

331

332

333

334

335

336

337

338

339

340

341

342

343

344

X1701301

X1701302

X1701303

XPS18M

XPSW09

X1701306

XPW05M

XPN04M

XPCB02

SIDE�PANEL

TIE�BAR

RUBBER�FOOT

351

352

353

X1701351

X1701352

X1701353

KNOB�FEMALE�M6-1.0

WORKING�TABLE

TABLE�INSERT�13/8"�HOLE

TABLE�INSERT�13/4"�HOLE

PHLP�HD�SCR�M8-1.25�X�20

FLAT�WASHER�3/8"

TAPER�PIN�8�X�75MM

FENCE�BODY�RIGHT

CLAMP�STUD

FENCE�BODY�LEFT

WOODEN�FENCE

LOCK�HANDLE�M12-1.75

FLAT�WASHER�1/2"

FLAT�WASHER�3/8"

KNOB�M8-1.25�FEMALE

LOCK�WASHER�1/2"

HEX�BOLT�M12-1.75�X�20

ADJUSTING�SCREW�STUD

HAND�KNOB�8MM�PINNED

ROLL�PIN�3�X�20

PHLP�HD�SCREW�M6-1�X�12

HALF�COLLAR

ADJUSTING�SHAFT

FLAT�WASHER�1/2"

HEX�NUT�M12-1.75

HEX�BOLT�M8-1.25�X�12

FLAT�WASHER�3/8"

HOLD�DOWN�BAR

PHLP�HD�SCR�M4-0.7�X�25

ON/OFF�PADDLE�SWITCH

SWITCH�LAMELLA

FLAT�WASHER�4MM

HEX�NUT�M4-0.7

CARRIAGE�BOLT�5/16-18�x�1/2

FLAT�WASHER�3/8

HEX�NUT�5/16-18

PHLP�HD�SCR�M5-0.8�X�12

EXT�TOOTH�WASHER�5MM

HEX�NUT�M5-0.8

353A X1701353A

354

355

356

357

358

359

360

361

362

363

364

365

366

367

368

369

370

371

372

373

374

375

376

377

378

379

380

381

382

383

384

385

386

387

388

389

390

391

392

393

394

395

396

397

398

399

XPS04M

XPW02

X1701356

X1701357

X1701358

X1701359

X1701360

X1701361

XPW01

XPW02

XPN02

XPS08M

XPTLW02M

XPN06M

X1701315

X1701316

X1701317

XPN03M

XPW02

X1701320

X1701321

XPWRCRD110L POWER�CORD�W/PLUG

XPWRCRD110S MOTOR�CORD

XPW02

SHELF

X1701364

XPLW07

XPB49M

X1701367

X1701368

XPRP42M

XPS14M

X1701371

X1701372

XPW01

XPN09M

XPB06M

XPW02

X1701377

XPS38M

X1701379

XPN03M

XPW02

X1701382

X1701383

XPN04M

X1701385

XPB20M�

X1701387

X1701388

X1701389

XPRP42M

X1701391

X1701392

XPRP42M

X1701394

XPB26M

ELECTRICITY�LABEL

ID�/�WARNING�LABEL

HEX�NUT�M8-1.25

FLAT�WASHER�3/8"

STRAIN�RELIEF

SPINDLE�PULLEY�GUARD

X1701324

X1701325

XPW02

SAFETY�GLASSES�LABEL

READ�MANUAL�LABEL

FLAT�WASHER�3/8"

HEX�BOLT�M8-1.25�X�12

TABLE�LEG

UNPLUG�MACHINE�LABEL

HEX�BOLT�M8-1.25�X�25

HEX�BOLT�M12-1.75�X�30

LOCK�WASHER�12MM

TABLE�SUPPORT

XPB06M

X1701328

X1701329

XPB07M

PHLP�HD�SCR�M4-0.7�X�10

GUARD�MOUNTING�POST

HEX�NUT�M8-1.25

XPB27M

XPLW05M

X1701333

X1701334

XPW06

XPS17M

XPHTEK13M

XPW02

X1701339

X1701340

X1701341

X1701342

X1701343

X1701344

FLAT�WASHER�3/8"

MOUNTING�BRACKET

HAND�KNOB�M10-1.5�X�28

HEX�NUT�M4-0.7

SAFETY�GUARD

HEX�BOLT�M8-1.25�X�30

HOUSING�BRACKET

CLAMP�SLEEVE�LEFT

STUFF�RING

ROLL�PIN�3�X�20MM

LOCK�BAR

HAND�KNOB�12MM,�PINNED

ROLL�PIN�3�X�20MM

CLAMP�SLEEVE�RIGHT

HEX�BOLT�M12-1.75�X�30

SPECIAL�SPINDLE�NUT

KEYED�SAFETY�WASHER

RUB�COLLAR�1/2"�X�1-3/16"�X�3/16"

RUB�COLLAR�1/2"�X�13/16"�X�1/4"

MITER�BLOCK

FLAT�WASHER�1/4"

PHLP�HD�SCR�M4-0.7�X�6

TAP�SCREW�M3.5�X�12

FLAT�WASHER�3/8"

SUPPORT�POLE

STUD�BOLT

ANTI-KICKBACK�PIN

MITER�BAR

ALUMINUM�ALLOY�FENCE

RIGHT�FENCE�LID

LEFT�FENCE�LID

MITER�GAUGE�BODY

PLASTIC�HANDLE

POINTER

344A X1701344A

345

346

347

348

349

350

X1701345

X1701346

X1701347

XPHTEK9M

X1701349

XPCB04M

X1701396

X1701397

X1701398

X1701399

SELF�TAP�SCREW�M3�X�15

TENSION�PIN�2�X�16MM

CARRIAGE�BOLT�M6-1�X�35

Continued on next page

-28-

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

REF

400

401

402

403

404

405

407

407A

408

409

410

411

412

413

414

415

416

417

418

419

420

421

422

423

424

425

426

427

428

429

430

PART�#

X1701400

X1701401

X1701402

X1701403

X1701404

X1701405

X1701407

X1701407A

XPK48M

X1701409

XPR25M

X1701411

XP6204

X1701413

X1701414

XP6204

X1701416

X1701417

X1701418

X1701419

XPSS20M

X1701421

X1701422

X1701423

X1701424

X1701425

X1701426

XPB06M

DESCRIPTION

RUB�COLLAR�1/2"�X�13/16"�X�3/8"

CUTTER�SPINDLE

COLLET�NUT

COLLET�1/4"

COLLET�1/2"

COLLET

REF

431

432

PART�#

XPSS01M

X1701432

DESCRIPTION

SET�SCREW�M6-1�X�10

MOTOR

432-1 XPC300S

S.�CAPACITOR�200MFD�125VAC

432-2 X1701432-2 CAPACITOR�COVER

432-3 X1701432-3 WIRING�BOX�

432-4 X1701432-4 MOTOR�FAN

SPINDLE�CARTRIDGE�ASSY

SPINDLE�CARTRIDGE

KEY�4�X�4�X�20MM

CLAMP�RING

INT�RETAINING�RING�47MM

WAVY�WASHER�45MM

BALL�BEARING�6204

SPINDLE�HOUSING

BALL�BEARING�SLEEVE

BALL�BEARING�6204

SPINDLE�PULLEY

LOWER�SPINDLE�NUT

BEARING�CONE

COIL�SPRING

SET�SCREW�M8-1.25�X�8

SPRING�COLLAR

STUD�M12-1.75�X�355

SLIP-ON�HANDLE

432-5 X1701432-5 MOTOR�FAN�COVER

433

434

435

436

437

438

439

440

441

442

443

444

445

446

447

448

449

450

451

452

453

454

455

XPK01M

XPB20M

XPLW04M

XPW02

XPB75M

XPW01

X1701439

XPW02

XPN03M

XPLW05M

XPLW04M

XPW06

X1701445

XPS14M

X1701447

X1701448

X1701449

X1701450

X1701451

X1701452

X1701453

X1701454

X1701455

KEY�5�X�5�X�22MM

HEX�BOLT�M8-1.25�X�35

LOCK�WASHER�8MM

FLAT�WASHER�3/8"

HEX�BOLT�M12-1.75�X�35

FLAT�WASHER�1/2"

MOTOR�MOUNT�PLATE

FLAT�WASHER�3/8"

HEX�NUT�M8-1.25

LOCK�WASHER�12MM

LOCK�WASHER�8MM

FLAT�WASHER�1/4"

TWO�CORD�CLAMP

PHLP�HD�SCR�M6-1�X�12

FWD/REV�SWITCH

SWITCH�BRACKET

TABLE�SPACER�KIT

DRAW�BAR�M8-1.0�X�130

TAPER�NUT�M8-1.25

FLAT�BELT�690�X�10MM

HEX�BOLT�M8-1.25�X�12

FLAT�WASHER�3/8"

BELT�GUARD

FLAT�WRENCH�23MM

FLAT�WRENCH�26MM

FLAT�WRENCH�30MM

RUB�COLLAR�1/2"�X�13/16"�X�1/2"

HEX�BOLT�M12-1.75�X�40

MITER�GAUGE�ASSEMBLY

XPW02

X1701429

X1701430

MOTOR�PULLEY

-29-

Download from Www.Somanuals.com. All Manuals Search And Download.

Warranty

Woodstock International, Inc. warrants all SHOP FOX^®machinery to be free of defects from work-

manship and materials for a period of two years from the date of original purchase by the original

owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence

or accidents, lack of maintenance, or reimbursement of third party expenses incurred.

Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX^®

machine or machine part which in normal use has proven to be defective, provided that the original

owner returns the product prepaid to the SHOP FOX^®factory service center or authorized repair

facility designated by our Bellingham, WA office, with proof of their purchase of the product within

two years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged

defect through inspection. If it is determined there is no defect, or that the defect resulted from

causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must

bear the cost of storing and returning the product.

This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be

implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited

to the duration of this written warranty. We do not warrant that SHOP FOX^®machinery complies

with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under

this warranty exceed the purchase price paid for the product, and any legal actions brought against

Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall

in no event be liable for death, injuries to persons or property or for incidental, contingent, special or

consequential damages arising from the use of our products.

Every effort has been made to ensure that all SHOP FOX^®machinery meets high quality and durabil-

ity standards. We reserve the right to change specifications at any time because of our commitment to

continuously improve the quality of our products.

Download from Www.Somanuals.com. All Manuals Search And Download.

W1701 1HP Shaper

Warranty Registration

Name___________________________________________________________________________________

Street __________________________________________________________________________________

City _________________________State___________________________Zip________________________

Phone #______________________Email __________________________Invoice #___________________

Model #_________Serial #______________Dealer Name__________________Purchase Date___________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us

develop better products and services. Of course, all information is strictly confidential.

1. How did you learn about us?

_____ Advertisement

____ Friend

____ Website

____ Local Store

____ Other:

_____ Mail Order Catalog

2. How long have you been a woodworker/metalworker?

_____ 0-2 Years _____ 2-8 Years ____8-20 Years

_____ 20+ Years

3. How many of your machines or tools are Shop Fox^®?

_____ 0-2 _____ 3-5 ____6-9

_____ 10+

____ No

4. Do you think your machine represents a good value?

_____ Yes

5. Would you recommend Shop Fox^®products to a friend? _____ Yes

6. What is your age group?

_____ 20-29

_____ 50-59

____ 30-39

____ 60-69

____ 40-49

____ 70+

7. What is your annual household income?

_____ $20,000-$29,000

_____ $50,000-$59,000

____ $30,000-$39,000

____ $60,000-$69,000

____ $40,000-$49,000

____ $70,000+

8. Which of the following magazines do you subscribe to?

____ Cabinet Maker

____ Family Handyman

____ Hand Loader

____ Popular Mechanics

____ Popular Science

____ Popular Woodworking

____ Practical Homeowner

____ Precision Shooter

____ Projects in Metal

____ RC Modeler

____ Today’s Homeowner

____ Wood

____ Wooden Boat

____ Woodshop News

____ Woodsmith

____ Handy

____ Home Shop Machinist

____ Journal of Light Cont.

____ Live Steam

____ Model Airplane News

____ Modeltec

____ Old House Journal

____ Woodwork

____ Woodworker West

____ Woodworker’s Journal

____ Other:

____ Riﬂe

____ Shop Notes

____ Shotgun News

9. Comments:__________________________________________________________________

_____________________________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

FOLD ALONG DOTTED LINE

Place

Stamp

Here

WOODSTOCK INTERNATIONAL INC.

P.O. BOX 2309

BELLINGHAM, WA 98227-2309

FOLD ALONG DOTTED LINE

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

Download from Www.Somanuals.com. All Manuals Search And Download.

Winegard Power Supply RV 7012 User Manual
Woods Equipment Brush Cutter BW126X User Manual
Xerox Network Card 3100MFP User Manual
Yamaha Guitar EG 011456 User Manual
Zanussi Dishwasher ZDT 6454 User Manual
Zanussi Washer 132985450 User Manual
Zanussi Washer Z 818 User Manual
Zebra Technologies Printer Accessories 110PAX4 User Manual
Zebra Technologies Printer Eltron Card Printer User Manual
Zenoah Trimmer CHT2301, HT2301 User Manual