1028310
4-POINT SUB-FRAME MOUNTING KIT
for BH90-X Backhoe
on New Holland® Tractors
TT60A, TT75A
includes Hose Kits
1028360, 1029730
and Mount Kit 1029700
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
„ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
grene, serious injury, or death will result. CON-
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
!
LEA EL INSTRUCTIVO!
Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
„ To prevent contamination during maintenance
and storage, clean and then cover hose ends, fit-
tings, and hydraulic ports with tape.
„ Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
In addition to the design and configuration of
equipment, hazard control and accident preven-
tion are dependent upon the awareness, con-
cern, judgement, and proper training of
personnel involved in the operation, transport,
maintenance, and storage of equipment.
„ This mounting kit is designed to provide secure
mounting and adequate operator clearance for
most operators when properly installed. Check
clearance dimensions shown below to be sure you
have installed seat bracket correctly. In some
cases it may be necessary to adjust the seat to the
lowest position and/or as far forward as possible in
order to achieve the ideal 40-inch clearance. For
36.5-inch radius operation, taller operators may
need to wear a hardhat for greater comfort and
safety.
It has been said, “The best safety device is an
informed, careful operator.” We ask you to be
that kind of operator.
„ This Sub-Frame Mounting Kit is only for the
backhoes and tractors specified in the Sub-Frame
Mount Installation section of this manual. Any
other use or modification of this mounting kit may
result in serious injury or death.
„ Hydraulics must be connected as instructed in
this manual. Do not substitute parts, modify, or
connect in any other way.
„ After connecting hoses, check that all control
lever positions function as instructed in the Opera-
tor's Manual. Do not put into service until control
lever and equipment movements are correct.
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
„ Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
„ Know your controls and how to stop engine and
attachment quickly in an emergency.
„ Protective hose sleeves must cover all hydrau-
lic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
„ Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
(Safety Rules continued on next page)
4-Point SFMK (Rev. 5/8/2006)
Safety 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
(Safety Rules continued from previous page)
„ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
„ Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
„ Before operating, make sure stabilizer pads are
lowered firmly to the ground. Stabilizer arms pro-
vide support for the backhoe and support for the
backhoe mounting brackets.
„ The only time the backhoe may be operated
from a position other than the operator seat is dur-
ing backhoe attachment and removal. Operator
must:
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
•
Read Mounting Kit Manual instructions on
attaching and removing backhoe and use
extreme care.
•
stabilizer arms or along side of tractor to avoid
being trapped should the boom swing control
be accidentally activated.
Always stand between rear tire and backhoe
„ Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
„ Never leave equipment unattended with engine
running or with bucket in raised position. Always
engage swing and boom transport locks, relieve
system pressure by operating controls, and
remove ignition key before leaving equipment.
„ Remove seat and upper support assembly
before installing or removing backhoe from tractor.
Failure to comply may result in equipment failure
and/or personal injury.
„ Refer to backhoe manual and follow all mainte-
nance safety rules and instructions.
„ Make sure attachment is properly secured,
adjusted, and in good operating condition.
„ Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its compo-
nents in any way.
„ A minimum 20% of tractor and equipment
weight must be on the tractor front wheels when
attachments are in transport position. Without this
weight, tractor could tip over, causing personal
injury or death. The weight may be attained with a
loader. Weigh the tractor and equipment. Do not
estimate.
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
„ Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
„ Do not install backhoe and required counter-
weights on tractor if the total tractor and equipment
weight then exceeds the ROPS weight certification
of the tractor. To reduce overall weight of unit,
remove liquid from rear tires and remove mid-
mount mower, if equipped.
„ Make sure all safety decals are installed.
Replace if damaged. (See Parts section for loca-
tion.)
™
4 Safety
4-Point SFMK (Rev. 5/8/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
BACKHOE SUB-FRAME INSTALLATION
Tractor Preparation
■
Only use 1028310 4-Point Sub-Frame Mount-
ing Kit for mounting Woods BH90-X backhoe on
New Holland® TT60A or TT75A tractors equipped
with Woods LU126 loader. Use mount kit 1029700
and 1028310 Sub-Frame Mounting Kit to mount
Woods BH90-X backhoe on New Holland® TT60A
or TT75A tractors equipped with New Holland
620TL Loader. Any other use or modification of
this mounting kit may result in serious injury or
death.
For installing this sub-frame, references to right, left,
forward and rearward directions are determined from
the operator’s position in the tractor seat.
DP1
Figure 1. Reposition Anti-Sway Links
Do not install 1028310 4-point sub-frame on a tractor
without a Woods or New Holland loader mount
attached.
Refer to the WOODS BH90-X Backhoe Operator’s
Manual for backhoe assembly instructions.
Leave all hardware loose until sub-frame has been fit
up or otherwise specified in the instructions.
Remove
1. Place jackstands under rear axle and remove
both rear tires.
2. Disconnect the tractor anti-sway links from the
axle brackets. Secure sway links to the drawbar
bracket with sway link pins and safety pins (22)
supplied in kit. See Figure 1.
3. Remove top link.
Remove
4. Remove the lower ROPS bracket from the bottom
of the rear axle (Figure 2). Leave ROPS bolts in
place.
DP2
NOTE: Only work on one side of the tractor at a
time. ROPS may become unstable if both ROPS
brackets are removed at the same time.
Figure 2. Remove Hydraulic Line & ROPS Bracket
5. 1028360 Hose Kit Only: Disconnect the loader
valve PBY hose from the tractor steel hydraulic
line under the right side of the operator’s platform.
(Right Side Shown)
6. Disconnect the steel hydraulic line from the
hydraulic valve at the rear of the tractor and
remove the hydraulic line. See Figure 2.
As a valued customer, Woods appreciates your comments. Once sub-frame and hydrau-
lic hoses have been installed, please take a few minutes to complete the Sub-Frame
Mount Evaluation sheet that was supplied with your sub-frame. Your comments will help
us continue to bring you quality products.
MAN0715 (Rev. 10/31/2008)
Installation 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Install 1029700 Mount Kit
For New Holland Loader Mount Only
This mount kit is needed to connect sub-frame mount-
ing kit 1028310 to the New Holland 620TL loader
mount.
1. Remove toolbox and toolbox bracket from the
right loader mount if equipped.
2. Attach right backhoe bracket (1) to the inside of
New Holland loader mount and toolbox bracket
(3) to the outside of loader mount.
3. Secure using two cap screws (4), hardened flat
washers (5), one tube support (7) and two flange
lock nuts (6).
Figure 3. Right Backhoe Bracket Installation
NOTE: Tube support (7) is placed between the
two rear holes on the mount.
3
7
1
4. Attach toolbox to toolbox bracket (3) using hard-
ware previously removed.
5. Repeat steps to install left backhoe bracket (2) to
left loader mount. See Figure 5.
1. 1029702 Right backhoe bracket
2. 1029703 Left backhoe bracket
3. 1029704 Toolbox bracket
6
4. 300469 5/8 NC x 6-1/2 HHCS GR5
4
5.
6.
57817 5/8 Hardened flat washer
19025 5/8 NC Flange lock nut
DP7
7. 1029774 Tube support
Figure 4. Right Backhoe Bracket Installed
7
2
6
4
Figure 5. Left Backhoe Bracket Installed
6 Installation
MAN0715 (rev. 10/31/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Tractor Brackets
1. Place right tractor bracket (1) under right side of
tractor. Use a hydraulic floor jack to help raise
and hold tractor bracket in position.
ROPS
Hardware
2. Attach right tractor bracket (1) to right loader
mount or right backhoe bracket (New Holland
Mount) using one hex flange screw (11) and hex
flange nut (18). See Figure 7.
3. Raise tractor bracket up and attach it to the bot-
tom of the rear axle using ROPS hardware previ-
ously removed.
11
18
4. Secure tractor bracket to the back of the rear axle
using two cap screws (7) and hardened flat wash-
ers (14). See Figure 8.
DP3
5. Attach tractor bracket to the bottom of the tractor
using two cap screws (8) and hardened flat wash-
ers (14).
Figure 7. Right Tractor Bracket to Loader Mount
6. Install remaining two hex flange screws (11) and
hex flange nuts (18) to the loader mount or back-
hoe bracket.
ROPS
Hardware
7. Repeat steps to install left tractor bracket (2).
8. Torque hardware:
7
14
M16 x 1.5P x 45 mm . . . . . . 133 lbs-ft. (181 N-m)
M16 x 1.5P x 40 mm . . . . . . 184 lbs-ft. (250 N-m)
5/8 NC x 1-3/4 HFS . . . . . . 170 lbs-ft. (230 (N-m)
14
DP4
8
Figure 8. Right Tractor Bracket Installed, Rear Axle
1. 1028308 Right tractor bracket
2. 1028309 Left tractor bracket (not shown)
7. 307431 M16 x 1.5P x 45 mm HHCS
8. 1026337 M16 x 1.5P x 40 mm HHCS CL10.9
11.
14.
19024 5/8 NC x 1-3/4 HFS GR5
57817 5/8 Hardened flat washer
18. 1028718 5/8 NC Flange hex nut
†.
Tractor hardware
Figure 6. Tractor Bracket Installation
MAN0715 (Rev. 10/31/2008)
Installation 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach Backhoe Mounts to Backhoe
NOTE: Leave all hardware loose until backhoe has
been mounted to the tractor.
1. Attach right backhoe mount (3) and left backhoe
mount (4) to backhoe frame.
2. Secure into position using six (three per bracket)
cap screws (10), hardened flat washers (13), and
hex nuts (17).
3. Secure crossbrace (5) to backhoe brackets using
four cap screws (12), hardened flat washers (15),
and hex nuts (19).
3. 1014450 Right backhoe mount
4. 1014451 Left backhoe mount
5. 1014467 Crossbrace
10.
12.
13.
15.
17.
19.
735 3/4 NC x 2 HHCS GR5
24576 1/2 NC x 1-3/4 HHCS GR5
57798 3/4 Hardened flat washer
57816 1/2 Hardened flat washer
1450 3/4 NC Hex nut
Figure 9. Backhoe Bracket Installation
1093 1/2 NC Hex nut
HOSE KIT INSTALLATION
„ Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety gog-
gles. Hydraulic fluid under pressure can easily
penetrate skin and will cause serious injury or
death.
„ Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking
before starting power unit or using equipment.
Check and route hoses carefully to prevent dam-
age. Hoses must not be twisted, bent sharply,
kinked, frayed, pinched, or come into contact with
any moving parts. Operate moveable components
through full operational range to check clear-
ances. Replace any damaged hoses immediately.
„ Make sure that all operating and service per-
sonnel know that if hydraulic fluid penetrates
skin, it must be surgically removed as soon as
possible by a doctor familiar with this form of
injury or gangrene, serious injury, or death will
result. CONTACT A PHYSICIAN IMMEDIATELY IF
FLUID ENTERS SKIN OR EYES. DO NOT DELAY.
8 Installation
MAN0715 (rev. 10/31/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
1028360 HOSE KIT
Install Fittings and Hose
1028360 Hose Kit is used to connect backhoe
hydraulic hoses to the tractor rear hydraulic valve and
the Woods loader control valve.
1. 1028358 Hose, 60" x 3/8 NPTM x 7/8 JICM
4. 1010920 Adapter, M22 x 3/4 JICM
5. 315036 Adapter, 3/8 NPTM x 3/4 JICF
1. Attach adapter (4), adapter (5) and female quick
coupler (6) into the opening on the hydraulic valve
at the rear of the axle.
6.
7.
64299 Quick coupler, female 3/8
64300 Quick coupler, male 3/8
2. Attach male quick coupler (7) to hose (1).
3. Attach opposite end of hose (1) to the PBY hose
from the loader control valve.
4. Route hose (1) over rear axle and out the back of
the tractor.
4
5
6
DP5
Figure 10. Hydraulic Valve Fittings Installed
Figure 11. Bulkhead Bracket Installation
Install Hoses to Backhoe Valve
1. Attach adapter (3) to the IN and OUT ports on the
backhoe control valve.
2. Attach female quick coupler (6) to hose (2).
Attach opposite end of hose to the IN port on the
backhoe valve.
3. Attach male quick coupler (7) to second hose (2).
Attach opposite end of hose to the OUT port of
backhoe valve.
2. 1013325 Hose, 48" x 3/8 NPTM x 3/4 JICF
3. 316016 Adapter, 3/4 JICM x 7/8 ORBM
6.
7.
64299 Quick coupler, female
64300 Quick Coupler, male
Figure 12. Backhoe Hose Connection
MAN0715 (Rev. 10/31/2008)
Installation 9
Download from Www.Somanuals.com. All Manuals Search And Download.
1029730 HOSE KIT
Install Fittings
1029730 Hose Kit is used to connect backhoe
hydraulic hoses to the tractor hydraulic line and the
New Holland loader control valve.
1. Disconnect the loader control valve PBY hose
from the hydraulic hard line below the tractor
seat.
2. Attach adapter (2), adapter (6) and female quick
coupler (4) to the hydraulic hard line (Figure 13).
6
3. Attach adapter (3), adapter (6) and male quick
coupler (5) to the PBY hose from the loader con-
trol valve.
2
4
DP10
4. Route PBY hose over rear axle.
Figure 13. Hydraulic Fitting Installed
2. 1002613 Adapter, M22 x 1.5 x 3/4 JICM
3. 1010920 Adapter, M22 x 1.5 x 3/4 JICM
4.
5.
64299 Quick coupler, female 3/8
64300 Quick coupler. male 3/8
6. 315036 Adapter, 3/8 NPTM x 3/4 JICF
7. 316016 Adapter, 3/4 JICM x 7/8 ORBM
Figure 14. Hydraulic Fitting Installation
Install Hoses to Backhoe Valve
1. Attach adapter (7) to the IN and OUT ports on the
backhoe control valve.
2. Attach female quick coupler (4) to hose (1).
Attach opposite end of hose to the IN port on the
backhoe valve.
3. Attach male quick coupler (5) to second hose (1).
Attach opposite end of hose to the OUT port of
backhoe valve.
1. 1029729 Hose, 72" x 3/8 NPTM x 3/4 JICF
4.
5.
64299 Quick coupler, female
64300 Quick Coupler, male
Figure 15. Backhoe Hose Connection
7. 316016 Adapter, 3/4 JICM x 7/8 ORBM
10 Installation
MAN0715 (rev. 10/31/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
Mount Backhoe to Tractor
Check Hydraulic System
Check all hydraulic fittings and lines to be sure they
are tight and free of kinks or twists.
Mount Backhoe
„ This mounting kit is designed to provide
secure mounting and adequate operator clear-
ance for most operators when properly installed.
Check clearance dimensions shown below to be
sure you have installed seat bracket correctly. In
some cases it may be necessary to adjust the seat
to the lowest position and/or as far forward as
possible in order to achieve the ideal 40-inch
clearance. For 36.5-inch radius operation, taller
operators may need to wear a hardhat for greater
comfort and safety.
1. Remove the backhoe seat assembly.
2. Back tractor up to backhoe and center mount
between the tractor rear tires. Position tractor so
that the hydraulic system can be connected. Shut
off tractor, set brake, remove key.
3. Attach backhoe hydraulic system.
A. Connect male quick coupler on hose from
OUT port on the backhoe control valve to the
female quick coupler on the tractor rear hydraulic
valve or hydraulic hard line below tractor seat.
B. Connect female quick coupler on hose from
the backhoe valve to the female quick coupler on
the end of hose from the loader valve PBY port.
4. With the tractor PTO and transmission in neutral,
start the engine and run at low idle. Hydraulic
power is provided when the tractor is started.
NOTE: Very little engine power is required to
operate the hydraulic system in this mode.
Should the engine pull down excessively, check
the plumbing hook-up for reversed lines or a con-
trol lever stuck in an operating position.
NOTE: You will use the backhoe hydraulics to
maneuver the backhoe brackets into position.
Use care in this procedure to avoid being trapped
between tractor and backhoe or between back-
hoe parts.
„ The only time the backhoe may be operated
from a position other than the operator seat is
during backhoe attachment and removal. Opera-
tor must:
• Read Mounting Kit Manual instructions on
attaching and removing backhoe and use
extreme care.
• Always stand between rear tire and backhoe
stabilizer arms or along side of tractor to avoid
being trapped should the boom swing control
be accidentally activated.
„ Remove seat and upper support assembly
before installing or removing backhoe from power
unit. Failure to comply may result in equipment
failure and/or personal injury.
(Continued on next page.)
MAN0715 (Rev. 10/31/2008)
Installation 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Mount Backhoe to Tractor (Continued)
10. Install cap screws (9) and slotted hex nuts (16).
Tighten with 1-1/2 inch open end wrench provided
with kit. Return wrench to storage position (see
Figure 16).
Refer to Figure 16.
5. Using the backhoe hydraulics position the back-
hoe brackets at a slight angle, approximately 5 to
10 degrees.
11. Secure hex nut into position with klik pin (20).
12. Shut off tractor and remove key.
6. Raise backhoe up by lowering stabilizers and
boom section until backhoe mounting pins on
backhoe brackets are slightly lower than tractor
bracket hooks.
13. Tighten hardware with backhoe secured to the
tractor. This will ensure proper alignment and fit-
up for future installation.
7. Slowly move tractor back until backhoe brackets
are positioned below the tractor bracket hooks.
Set tractor brake.
1/2 NC x 1-34. . . . . . . . . . . . . 85 lbs-ft (115 N-m)
3/4 NC x 2 . . . . . . . . . . . . . . 297 lbs-ft (403 N-m)
8. Raise backhoe bracket bottom mounting pins into
14. Reinstall seat.
tractor bracket bottom hooks.
15. Start tractor and put backhoe into transport posi-
9. Rotate backhoe bracket upper mounting slots
over tractor bracket mounting hole and align
holes.
tion (see backhoe operator’s manual).
NOTE: Install swing lock before transporting.
9. 1006860 1" NC x 4 Cap screw GR5
16. 1006861 1" NC Slotted hex nut
20.
62043 1/4 x 1-3/4 Klik pin
Figure 16. Backhoe to Tractor Installation
12 Installation
MAN0715 (rev. 10/31/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove Backhoe from Tractor
7. Use the boom to relieve excess pressure on 1
inch bolts and remove bolts.
8. Tilt backhoe main frame to separate slots on the
„ The only time the backhoe may be operated
from a position other than the operator seat is
during backhoe attachment and removal. Opera-
tor must:
backhoe brackets from the tractor brackets.
9. Raise stabilizers until backhoe brackets slide out
of hooks on the bottom of the tractor brackets.
• Read Mounting Kit Manual instructions on
attaching and removing backhoe and use
extreme care.
• Always stand between rear tire and backhoe
stabilizer arms or along side of tractor to avoid
being trapped should the boom swing control
be accidentally activated.
10. Move tractor forward to clear backhoe brackets.
11. Lower backhoe until backhoe main frame is firmly
on the ground. Retract boom and dipper and
place bucket cutting edge flat on the ground. See
Figure 17. Connect transport lock and insert
swing lock pin.
NOTE: It may be necessary to place backhoe
main frame on 6" blocks if backhoe hose lengths
are not long enough to achieve proper clearance
when separating backhoe from tractor.
„ Remove seat and upper support assembly
before installing or removing backhoe from power
unit. Failure to comply may result in equipment
failure and/or personal injury.
12. Turn off engine, set brakes, and remove key.
13. Disconnect backhoe hydraulic system. See
“STORAGE” on page 14.
13. Reinstall seat assembly.
1. Position tractor on a hard, level surface and cen-
ter the backhoe boom.
NOTE: For instructions on extended storage, see
2. Lower stabilizers and take backhoe weight off
backhoe operator’s manual.
tractor.
3. Lower boom and dipper to form 90-degree angle
and rest bucket on the ground.
4. Remove the seat assembly.
5. Remove klik pins from bolt and nut assemblies.
6. Use 1-1/2 inch open end wrench supplied with the
mounting kit to remove hex nuts. Return wrench
to storage position (see Figure 16).
Figure 17. Backhoe Storage Position
MAN0715 (Rev. 10/31/2008)
Installation 13
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
Connect Hydraulic Hoses
Loader PBY
Hose
NOTICE
■
Failure to connect hoses together will result
in damage to tractor hydraulic system.
Tractor & Woods Loader: Connect male quick cou-
pler on end of hose from loader control valve to
female quick coupler in rear hydraulic valve when
backhoe is removed from tractor. See Figure 18.
Make sure 3-point lift arms do not interfere with hose.
Adjust hose as necessary to prevent interference.
Tractor & New Holland Loader: Connect male quick
coupler on end of hose from loader control valve to
female quick coupler in the hydraulic hard line below
the tractor seat when backhoe is removed from trac-
tor. See Figure 19
DP9
Figure 19. Hose Connection - Backhoe Removed
New Holland Loader
BACKHOE: Connect IN and OUT quick couplers
together to prevent dirt and debris from accumulating
in quick couplers. See Figure 20.
Figure 20. Backhoe Hose Connection
Figure 18. Hose Connection - Backhoe Removed
Woods Loader
Attach 3-Point Arms
Lower 3-point lift arms and anti-sway links can be
used on tractor when backhoe is removed.
Attach 3-point lift arms anti-sway links using the nor-
mal tractor connection.
Secure anti-sway links to tractor using sway link pins
and safety pins (22) provided in kit.
22.
15036 Safety pin, 3/16
14 Installation
MAN0715 (rev. 10/31/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
1028310 4-POINT SUB-FRAME MOUNTING KIT
21 - PN 1006885
WARNING
PINCH POINT
Keep hands
clear.
1006885
MODEL NO.
SERIAL NO.
Woods Equipment Company
Oregon, Illinois, U.S.A.
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
1
2
1028308
1028309
1014450
1014451
1014467
1006883
307431
1
1
1
1
1
1
6
4
2
6
6
4
6
Right tractor bracket
14
15
57817
57816
8
4
2
6
6
4
2
2
2
5/8 Hardened flat washer
Left tractor bracket
1/2 Hardened flat washer
1" NC Slotted hex nut
3/4 NC Hex nut
3
Right backhoe bracket
Left backhoe bracket
16 1006861
17 1450 *
18 1028718
4
5
Cross brace
5/8 NC Hex flange nut
1/2 NC Hex nut
6
1-1/2 Open end wrench
M16 x 1.5P x 45 mm HHCS
M16 x 1.5P x 40 mm HHCS CL10.9
1" NC x 4.0 HHCS GR5
3/4 NC x 2 HHCS GR5
5/8 NC x 1-3/4 HFS GR5
1/2 NC x 1-3/4 HHCS GR5
3/4 Hardened flat washer
19
20
1093 *
62043
7
1/4 x 1-3/4 Klik pin
8
1026337
1006860
21 1006885
22 15036 *
Decal, Warning - pinch point
Safety pin, 3/16 (not shown)
9
10
11
12
13
735 *
19024
24576 *
57798
† Tractor Hardware
HFS Hex Flange Screw
HHCS Hex Head Cap Screw
* Standard hardware, obtain locally
MAN0715 (Rev. 10/31/2008)
Parts 15
Download from Www.Somanuals.com. All Manuals Search And Download.
1029700 MOUNTING KIT
REF PART
QTY
DESCRIPTION
1
2
3
4
5
6
7
1029702
1
1
1
4
4
4
2
Right backhoe bracket
1029703
1029704
300469 *
57817
Left backhoe bracket
Toolbox bracket
5/8 NC x 6-1/2 HHCS GR5
5/8 Hardened flat washer
5/8 NC flange lock nut
Tube support
19025 *
1029774
* Standard hardware, obtain locally
1028360 HOSE KIT
REF PART
QTY
DESCRIPTION
1
2
3
4
5
6
7
1028358
1
2
2
1
1
2
2
Hose, 60" x 3/8 NPTM x 7/8 JICM
Hose, 48" x 3/8 NPTM x 3/4 JICF
Adapter, 3/4 JICM x 7/8 ORBM
Adapter, M22 x 1.5P x 3/4 JICM
Adapter, 3/8 NPTM x 3/4 JICF
Quick coupler, female
1013325
316016
1010920
315036
64299
64300
Quick coupler, male
16 Parts
MAN0715 (Rev. 10/31/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
1029730 HOSE KIT
REF PART
QTY
DESCRIPTION
1
2
3
4
5
6
7
1029729
2
1
1
2
2
2
2
Hose, 72" x 3/8 NPTM x 3/4 JICF
Adapter, M22 x1.5F x 3/4 JICM
Adapter, M22 x 1.5M x 3/4 JICM
Quick coupler, female
1002613
1010920
64299
64300
Quick coupler, male
315036
316016
Adapter, 3/8 NPTM x 3/4 JICF
Adapter, 3/4 JICM x 7/8 ORBM
MAN0715 (Rev. 10/31/2008)
Parts 17
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
SAE 2
SAE 5
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
8
lbs-ft
10
N-m
13
lbs-ft
14
N-m
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
7/16"
1/2"
6
18
37
12
17
19
26
27
9/16"
5/8"
23
31
35
47
49
67
36
48
55
75
78
106
163
232
325
569
907
1383
3/4"
55
75
85
115
164
230
403
642
979
120
171
240
420
669
1020
13/16"
15/16"
1-1/8"
1-5/16"
1-1/2"
78
106
149
261
416
634
121
170
297
474
722
110
192
306
467
METRIC SERIES
TORQUE
CHART
8.8
Metric Bolt Head
Identification
10.9
A
Metric
Grade 8.8
Metric
Grade 10.9
COARSE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
FINE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
A
A
Diameter &
Thread Pitch Wrench
(Millimeters)
Diameter &
Thread Pitch
(Millimeters)
Size
N-m
lbs-ft
6
N-m
lbs-ft
6
6 x 1.0
10 mm
13 mm
16 mm
18 mm
21 mm
24 mm
27 mm
30 mm
34 mm
36 mm
46 mm
8
11
27
8
8
11
29
8
6 x 1.0
8 x 1.0
8 x 1.25
10 x 1.5
12 x 1.75
14 x 2.0
16 x 2.0
18 x 2.5
20 x 2.5
22 x 2.5
24 x 3.0
30 x 3.0
20
15
20
21
16
22
39
29
54
40
41
30
57
42
10 x 1.25
12 x 1.25
14 x 1.5
16 x 1.5
18 x 1.5
20 x 1.5
22 x 1.5
24 x 2.0
30 x 2.0
68
50
94
70
75
55
103
163
250
363
507
684
861
1740
76
109
169
234
330
451
571
1175
80
151
234
323
457
623
790
1626
111
173
239
337
460
583
1199
118
181
263
367
495
623
1258
87
120
184
268
374
505
635
1283
125
172
244
332
421
867
133
194
270
365
459
928
Typical Washer
Installations
Bolt
Flat Washer
Lock Washer
8/9/00
Bolt Torque & Size Charts (Rev. 3/28/2007)
18 Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
5/8
3/4
7/8
IN
1
2
7
3
4
5
6
MM
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM 10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG .............................................................. Agriculture
MPa.........................................................Mega Pascal
N.......................................................................Newton
NC......................................................National Coarse
NF ...........................................................National Fine
NPSM.....................National Pipe Straight Mechanical
NPT.......................................... National Pipe Tapered
NPT SWF .........National Pipe Tapered Swivel Female
ORBM .......................................... O-Ring Boss - Male
P...........................................................................Pitch
PBY...................................................... Power-Beyond
psi..........................................Pounds per Square Inch
PTO..................................................... Power Take Off
QD....................................................Quick Disconnect
RH..............................................................Right Hand
ROPS........................... Roll-Over Protective Structure
RPM ........................................Revolutions Per Minute
RT ....................................................................... Right
SAE..........................Society of Automotive Engineers
UNC .....................................................Unified Coarse
UNF...........................................................Unified Fine
UNS......................................................Unified Special
ASABE.................... American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE ....... American Society of Agricultural Engineers
ATF ............................... Automatic Transmission Fluid
BSPP .............................British Standard Pipe Parallel
BSPTM ................British Standard Pipe Tapered Male
CV.....................................................Constant Velocity
CCW .............................................. Counter-Clockwise
CW............................................................... Clockwise
F ...................................................................... Female
FT .............................................................. Full Thread
GA .................................................................... Gauge
GR (5, etc.) ........................................... Grade (5, etc.)
HHCS ........................................Hex Head Cap Screw
HT........................................................... Heat-Treated
JIC .................Joint Industry Council 37° Degree Flare
LH.................................................................Left Hand
LT........................................................................... Left
m......................................................................... Meter
mm................................................................Millimeter
M.......................................................................... Male
Bolt Torque & Size Charts (Rev. 3/28/2007)
Appendix 19
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
Model Number: ____________________________
From (Dealer): __________________________________________
Serial Number: __________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set
forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
Woods backhoe models BH70-X, BH80-X, and BH90-X are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Duration (from date of delivery
Model Number
BW1260, BW1620, BW1800, BW2400
to the original purchaser)
8 years
BW240HD
7 years
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X,
BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240
6 years
Gearbox
PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2,
RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2,
9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD
components
5 years
3 years (1 year if used in rental or
commercial applications)
RDC54, RD60, RD72
Blade
spindles
RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2,
9204RD-2
3 years
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW180-3, BW1260,
BW1800, BW240, BW240HD, 2162, 3240, DS1260, DSO1260, DS1440, TS1680
Rust-through
10 years
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been
materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized
service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made
with parts other than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to
a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,
in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof
of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS
WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business,
revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute
machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS,
its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
F-3079 (Rev 8/26/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(Replacement Parts For All Models Except Mow’n Machine
Zero-Turn Mowers and Woods Boundary Utility Vehicles)
TM
TM
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-8494 (Rev. 6/23/2005)
Download from Www.Somanuals.com. All Manuals Search And Download.
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
©2008 Woods Equipment Company. All rights reserved. WOODS and the Woods logo are trademarks of Woods Equipment Company. All other
trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respec-
tive companies or mark holders. Specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|