SNOWBLOWER
SB54S
SB64S
SB74C
SB84C
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OWNER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DEALER CHECK LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
INDEX TO PARTS LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 39
PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . . . . . Inside Back Cover
Introduction 3
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Width Of Cut: . . . . . . . . . . . . . . . . . . SB54S. . . . . . . . . . . . . . . . . . . . . . .54"
SB64S. . . . . . . . . . . . . . . . . . . . . . .64"
SB74C. . . . . . . . . . . . . . . . . . . . . . .74"
SB84C. . . . . . . . . . . . . . . . . . . . . . .84"
Cutting Height . . . . . . . . . . . . . . . . . . . . . . . . . 24"(S Models) , 26"(C Models)
Number of Augers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Auger Diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15"
Fan Diameter . . . . . . . . . . . . . . . . . . SB54S/SB64S. . . . . . . . . . . . . . . . .22"
SB74C/SB84C . . . . . . . . . . . . . . . .24"
Auger Flighting Thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5/16" x 2"
Roller Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . #50
Chute Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 Deg.
Chute Length . . . . . . . . . . . . . . . . . . SB54S/SB64S. . . . . . . . . . . . . 24-1/4"
SB74C/SB84C . . . . . . . . . . . . . . . .29"
Operating Weight . . . . . . . . . . . . . . . SB54S. . . . . . . . . . . . . . . . . . . . 415lbs
SB64S. . . . . . . . . . . . . . . . . . . . 436lbs
SB74C. . . . . . . . . . . . . . . . . . . . 592lbs
SB84C. . . . . . . . . . . . . . . . . . . . 632lbs
PTO Horsepower Requirement: . . . . SB54S. . . . . . . . . . . . . . . . < = 25 H.P.
SB64S. . . . . . . . . . . . . . . . 15 - 35 H.P.
SB74C. . . . . . . . . . . . . . . . 30 - 50 H.P.
SB84C. . . . . . . . . . . . . . . . 35 - 60 H.P.
Tractor Hitch . . . . . . . . . . . . . . . . . . . SB54S/SB64S. . Limited CAT1 & CAT1
SB74C/SB84C . . . . . . . CAT1 & CAT2
PTO Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .540 RPM
Auger Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180 RPM
Gearbox Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 0.52 Qt SAE 80W-90
GENERAL INFORMATION
may be general in nature due to unknown and varying
operating conditions. However, through experience
and these instructions, you should be able to develop
procedures suitable to your particular situation.
„ Some illustrations in this manual show the
equipment with safety shields removed to provide
a better view. This equipment should never be
operated with any necessary safety shielding
removed.
The illustrations and data used in this manual were cur-
rent at the time of printing, but due to possible inline
production changes, your machine may vary slightly in
detail. We reserve the right to redesign and change the
machines as may be necessary without notification.
The purpose of this manual is to assist you in operating
and maintaining your snowblower. Read it carefully. It
furnishes information and instructions that will help you
achieve years of dependable performance. These
instructions have been compiled from extensive field
experience and engineering data. Some information
Throughout this manual, references are made to right,
left, forward and rearward directions. These are deter-
mined by sitting in the tractor operator's seat facing the
direction of forward travel.
MAN0869 (04/13/2011)
4 Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
PREPARATION
Safety is a primary concern in the design and
„ Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
„ Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
In addition to the design and configuration of
equipment, hazard control and accident preven-
tion are dependent upon the awareness, concern,
judgement, and proper training of personnel
involved in the operation, transport, maintenance
and storage of equipment.
It has been said “The best safety device is an
informed, careful operator.” We ask you to be that
kind of operator.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
TRAINING
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
„ Make sure attachment is properly secured,
adjusted, and in good operating condition.
„ Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
„
Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
„ Make sure spring-activated locking pin or collar
slides freely and is seated firmly in tractor PTO
spline groove.
„ If you do not understand any part of this manual
and need assistance, see your dealer.
„ Know your controls and how to stop engine and
attachment quickly in an emergency.
„ A minimum 20% of tractor and equipment
weight must be on the tractor front wheels when
attachments are in transport position. Without this
weight, front tractor wheels could raise up result-
ing in loss of steering. The weight may be attained
with front wheel weights, ballast in tires or front
tractor weights. Weigh the tractor and equipment.
Do not estimate.
„
Operators must be instructed in and be capable
of the safe operation of the equipment, its attach-
ments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
„ Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
„ Inspect and clear area of stones, branches, or
other hard objects that might be thrown, causing
injury or damage.
OPERATION
„ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
grene, serious injury, or death will result. CON-
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
„ Never place hands or body into discharge chute
or auger to unclog. Stored energy can cause auger
to quickly rotate when unclogging occurs and
cause severe injury or amputation. Stop engine,
remove key, disconnect driveline, and carefully
unclog, using a sturdy piece of wood.
„ Keep bystanders away from equipment.
„ Never allow children or untrained persons to
„ Never direct discharge toward people, animals,
operate equipment.
or property.
Safety 5
Snowblower_SRs (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
„ Do not operate or transport equipment while
under the influence of alcohol or drugs.
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
„ Operate only in daylight or good artificial light.
„ Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
„ Before performing any service or maintenance,
disconnect driveline from tractor PTO.
„ Always comply with all state and local lighting
and marking requirements.
„ NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.
„ Never allow riders on power unit or attachment.
„ Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt, place transmission in neutral, engage brake,
and ensure all other controls are disengaged
before starting power unit engine.
„ Operate tractor PTO at RPM listed on safety
decal located on fan housing above gearbox. Do
not exceed.
• Service work does not require going under-
neath implement.
• Read Operator's Manual for service instruc-
tions or have service performed by a qualified
dealer.
„ Do not operate PTO during transport.
„ Look down and to the rear and make sure area
is clear before operating in reverse.
„ Service and maintenance work not covered in
OWNER SERVICE must be done by a qualified
dealership. Special skills, tools, and safety proce-
dures may be required. Failure to follow these
instructions can result in serious injury or death.
„ Do not operate or transport on steep slopes.
„ Do not stop, start, or change directions sud-
denly on slopes.
„ Use extreme care and reduce ground speed on
slopes and rough terrain.
„ Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its compo-
nents in any way.
„ Use extreme care when working close to fences,
ditches, other obstructions, or on hillsides.
„ Your dealer can supply original equipment
hydraulic accessories and repair parts. Substitute
parts may not meet original equipment specifica-
tions and may be dangerous.
„ Watch for hidden hazards on the terrain during
operation.
„ Watch for traffic when operating near or cross-
ing roadways.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ Stop power unit and equipment immediately
upon striking an obstruction. Turn off engine,
remove key, inspect, and repair any damage before
resuming operation.
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
„ Make sure attachment is properly secured,
adjusted, and in good operating condition.
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
„ Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
„ Before performing any service or maintenance,
disconnect driveline from tractor PTO.
MAINTENANCE
„ Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
6 Safety
Snowblower_SRs (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
„
Make sure shields and guards are properly
„ Use a suitable lifting device of sufficient capac-
ity. Use adequate personnel to handle heavy com-
ponents.
installed and in good condition. Replace if damaged.
„ Do not disconnect hydraulic lines until engine is
stopped, power unit is properly secured, equip-
ment and all components are lowered to the
ground, and system pressure is released by oper-
ating all valve control levers.
STORAGE
„ Block equipment securely for storage.
„ Keep children and bystanders away from stor-
age area.
Safety 7
Snowblower_SRs (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
4 - 1033602
1 - 1033600
5 - 1033270
7 - 1033601
MAN0869 (04/13/2011)
8 Safety
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
2 - 1033274
8 - 1033273
3 - 1033271
6 - 1033272
9 - 1033176
BE CAREFUL!
Use a clean, damp cloth to clean safety decals.
Avoid spraying too close to decals when using a pressure washer;
high-pressure water can enter through very small scratches or under
edges of decals causing them to peel or come off.
Replacement safety decals can be ordered free from your Woods
dealer. To locate your nearest dealer, check the Dealer Locator at
1-800-319-6637.
MAN0869 (04/13/2011)
Safety 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The operator is responsible for the safe operation of
remove key, disconnect driveline, and carefully
unclog, using a sturdy piece of wood.
the snowblower. The operator must be properly
trained. Operators should be familiar with the tractor,
snowblower, and all safety practices before starting
operation. Read through safety rules and decals on
page 5 through page 9.
„ Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
„ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
grene, serious injury, or death will result. CON-
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
„
Operators must be instructed in and be capable
of the safe operation of the equipment, its attach-
ments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
„ Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
„ Make sure spring-activated locking pin or collar
slides freely and is seated firmly in tractor PTO
spline groove.
„ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
„ Operate tractor PTO at 540 RPM. Do not exceed.
„ Make sure attachment is properly secured,
adjusted, and in good operating condition.
„ Never allow children or untrained persons to
operate equipment.
„ Never go underneath equipment (lowered to the
ground or raised) unless it is properly blocked and
secured. Never place any part of the body under-
neath equipment or between moveable parts even
when the engine has been turned off. Hydraulic
system leak down, hydraulic system failures,
mechanical failures, or movement of control levers
can cause equipment to drop or rotate unexpect-
edly and cause severe injury or death. Follow Oper-
ator's Manual instructions for working underneath
and blocking requirements or have work done by a
qualified dealer.
„ If you do not understand any part of this manual
and need assistance, see your dealer.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
NOTICE
■
Be sure to complete the Pre-Operation Check
List on page 15 prior to operating this Snowblower.
„ Keep bystanders away from equipment.
PRINCIPAL COMPONENTS
„ Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
The snowblower has three main operating compo-
nents. A 15" diameter auger dislodges the snow and
carries it to a central fan. The snow is then discharged
by the fan and directed away from the blower through a
controllable spout.
„ Never place hands or body into discharge chute
or auger to unclog. Stored energy can cause auger
to quickly rotate when unclogging occurs and
cause severe injury or amputation. Stop engine,
MAN0869 (04/13/2011)
10 Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
The snowblower is mounted on a tractor 3-point hitch
and driven by the tractor PTO. A centrally located gear-
box directs power to the fan and auger.
4. Attach tractor center link to upper hitch point of
snowblower. Adjust length of center link until the
top edge of the frame ends are parallel to ground.
5. Adjust tractor lower 3-point arm anti-sway devices
to prevent snowblower from swinging side to side
during transport.
TRACTOR REQUIREMENTS
3-Point Hitch
The compact snowblower (C series) requires the trac-
tor to be equipped with a Category 1 or 2 three-point
hitch. The sub-compact (S series) snowblower requires
the tractor to be equipped with a limited Category 1 or
Category 1 three-point hitch.
6. Attach front PTO driveline from snowblower to
tractor. Slide front section of PTO driveline into
back section. Slide PTO shaft onto rear of tractor.
NOTICE
Hydraulic Circuit
Either closed-center or open-center systems can be
used for the optional hydraulic spout control.
■ If the PTO driveline is too long, severe driveline
and gearbox damage is possible when hooking up
the PTO driveline from the rotary snowblower to
the tractor. The front PTO driveline is long enough
to fit a variety of tractors. It is possible that the
front PTO driveline will need to be cut. There will be
NO benefit by cutting only one telescoping section.
Both sections of the driveline must be cut. DO NOT
FORCE THE PTO TO FIT.
Tire Configuration
For best results, the tractor wheels should be set nar-
rower than the cutting width of the snowblower. Wider
wheel settings will cause snow to be pulled under the
tractor and may require additional passes.
■ If attaching with quick hitch, the distance
between the tractor PTO and gearbox input shaft
will increase. Please follow the steps as you would
for a 3-point hitch to insure proper engagement.
PTO Shaft
The tractor must be configured to accept a 1-3/8" 6-
spline 540 RPM system and must meet horsepower
specifications. See specifications, page 4.
■ When attaching snow blower to multiple trac-
tors consider the drive length needed for each trac-
tor and whether the drive line will work in all
combinations.
Tractor Stability
„ A minimum 20% of tractor and equipment
weight must be on the tractor front wheels when
attachments are in transport position. Without this
weight, front tractor wheels could raise up result-
ing in loss of steering. The weight may be attained
with front wheel weights, ballast in tires or front
tractor weights. Weigh the tractor and equipment.
Do not estimate.
■ WARRANTY IS VOID IF THE PTO DRIVELINE IS
TOO LONG, resulting in gearbox, PTO, yoke or
cross bearing damage.
NOTE: The PTO driveline, when attached to the
tractor and gearbox, must not extend so there is
less than 10-3/4” (bilobe) or 4-1/2" (trilobe) of over-
lap within the PTO driveline.
DRIVELINE ATTACHMENT
Attach snowblower to tractor 3-point hitch (or quick
hitch if available). Do not attach driveline the first time
you attach the snow blower to the tractor. Raise and
lower snowblower to determine maximum and mini-
mum distance between tractor PTO shaft and gearbox
input shaft. If distance is too large, driveline will be too
short for proper engagement. If distance is too small,
driveline may bottom out in operation and damage
snowblower or tractor.
Figure 1. Tractor Stability (Typical)
ATTACHING SNOWBLOWER TO TRACTOR
1. Move the tractor into position in front of the snow-
blower. Move back slowly and carefully, not allow-
ing anyone to be between the tractor and the
snowblower.
If driveline is too short, please call your Woods dealer
for a longer driveline.
If driveline is too long, please follow instructions for
shortening driveline.
2. Turn off tractor engine.
3. Attach two lower arms of 3-point hitch with the two
hitch-pin assemblies.
(Rev. 9/8/2011)
Operation 11
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Cut upper shield to this overall dimension
SHORTENING DRIVELINE
1. Move snowblower up and down to get shortest
possible distance between tractor PTO shaft and
gearbox input shaft. Leave snowblower in mini-
mum distance position. Install jack stands under
snowblower for support.
2. Separate driveline into two halves and connect
them to tractor and gearbox.
3. Place driveline halves parallel to one another to
determine how much to shorten the driveline.
Figure 4. Cut Shield
6. Place cut portion of shield against end of shaft and
use as a guide. Mark and cut shaft.
Figure 2. Drive Halves Placed Parallel
4. Measure from end of upper shield to base of bell
on the lower shield (A). Add 1-1/4" to dimension
(A).
Figure 5. Cut Shaft to Length
A
7. Repeat step 4 through 6 for other half of drive.
8. File and clean the cut ends of both drive halves.
Ensure the drive halves slide smoothly together.
Do not run tractor if proper driveline engagement can-
not be obtained through these methods.
1-1/4"
Connect driveline to tractor PTO shaft, making sure
spring-activated locking collar slides freely and locks
driveline to PTO shaft.
MACHINE BREAK-IN
Although there are no operational restrictions on the
snowblower when used for the first time, the following
items are to be checked.
Figure 3. Determine Shield Length
A. After operating for 1/2 hour:
1. Check all nuts, bolts and other fasteners. Tighten
to their specified torque level.
2. Check drive chain tension. Adjust as required.
3. Check that auger, fan and spout are in good condi-
tion.
MAN0869 (04/13/2011)
12 Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Check oil level in the gearbox. Add as required.
5. Lubricate all grease points.
8. Ground Speed: Travel speed can vary between 1.5
and 8 mph depending on material and terrain con-
ditions. It is the responsibility of the operator to
note the condition of the job being done and set the
speed to obtain proper feeding rate and maintain
safe control of machine.
B. After operating for 5 to 10 hours:
1. Repeat items 1 through 4 of Section A.
2. Then go to normal Owner Service Section,
9. The PTO driveline is equipped with a shear bolt,
Figure 6, that protects drive system components
from shock loads if machine strikes an obstruction.
See parts section for bolt size and grade.
page 16.
OPERATION
Each operator should review this section of the manual
at the start of the season and as often as required to be
familiar with the machine. When using, follow this pro-
cedure:
1. Review and follow the "Pre-Operation Check List,"
page 15.
2. Review "Attaching Snowblower to Tractor" section,
page 11.
3. Before going to the field, review "Transporting"
section, page 14.
4. Position snowblower in a level area and lower into
working position.
5. Starting Snowblower:
■ Be sure area is clear of all bystanders.
■ Run engine at low idle.
Figure 6. Shear Bolts
10. Operating Requirements:
■ Slowly engage PTO control to start machine.
■ Slowly bring engine to rated PTO speed. Never
exceed rated speed
6. Stopping Machine:
„ Never direct discharge toward people, animals,
or property.
■ Slowly decrease engine speed to low idle.
■ Know where you are operating. Remove all
unwanted trash and debris before starting. It can
wrap around auger or be thrown out of machine
during operation.
■ Wait until PTO drive and snowblower have
slowed to low engine idle speed before disengag-
ing PTO drive.
■ Keep auger and fan in good condition. Do not
operate with a damaged fan or auger.
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
■ Do not allow the auger to hit and scalp ground
during operation. Hitting ground will pick up soil or
rocks that can be thrown out of machine.
■ To change direction of snow discharge, rotate
the discharge chute. It will rotate 270°.
To move a discharge chute equipped with an
optional hydraulic control, use tractor hydraulic
control to direct discharge left or right within its
270° range. It will not rotate a full 360°.
„ Before performing any service or maintenance,
disconnect driveline from tractor PTO.
7. Do not operate with bystanders in area. The
machine can pick up stones, sticks, wire and other
debris and throw it out with enough force to cause
severe injury or death to bystanders. Shut down
machine and wait for moving parts to stop before
approaching machine.
NOTE: For hydraulic rotator option, if chute turns
too quickly, adjust flow control on tractor hydrau-
lics.
NOTE: Operating hydraulic deflector cylinder
requires low tractor flow rates. When initially oper-
ating cylinder reduce tractor hydraulic flow rate to
Operation 13
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
prevent deflector damage and improve resolution
of deflector adjustment.
attachments are in transport position. Without this
weight, front tractor wheels could raise up result-
ing in loss of steering. The weight may be attained
with front wheel weights, ballast in tires or front
tractor weights. Weigh the tractor and equipment.
Do not estimate.
Adjusting Discharge Chute Position
■ The height of snow discharge is controlled by
position of chute deflector on discharge chute (8),
Figure 7. Remove clevis pin (5), and slide adjust-
ment strap (9) to selected discharge height. Rein-
stall clevis pin (5).
„ Never allow riders on power unit or attachment.
„ Do not operate PTO during transport.
NOTE: If possible, blow snow with the wind.
Beware of people or buildings in the area.
CAUTION
„ Always comply with all state and local lighting
and marking requirements.
NOTICE
■
Do not exceed 20 mph (32km/h). Reduce speed
on rough roads and surfaces.
When transporting snowblower, review and follow this
procedure:
■
Be sure all bystanders are clear of machine.
Be sure that machine is securely attached to
■
tractor and all retainer pins are installed.
5. Clevis Pin
■
■
Raise machine.
8. Discharge Chute
9. Adjustment Strap
Do not allow riders.
STORAGE
Figure 7. Discharge Chute Position
„ Block equipment securely for storage.
■ Keep bystanders away from equipment.
■ Wear appropriate hearing protection.
„ Keep children and bystanders away from stor-
age area.
After season's use, machine should be thoroughly
inspected and prepared for storage. Repair or replace
any worn or damaged components to prevent any
unnecessary down time at start of next season.
11. Depth of cut can be controlled with the skid shoes
or by tilting the blower forward or backward. Exces-
sive forward or backward tilt may cause U-joint to
flutter resulting in PTO shear bolt failure. Do not
run the PTO shaft at more than a 15° angle.
To insure a long, trouble free life, this procedure should
be followed when preparing unit for storage.
12. Allow the snowblower to work its way through the
snow rather than forcing it.
1. Clear area of bystanders.
13. In deep snow it may be necessary to raise the
snowblower for the first pass through and clean up
the remainder with a second pass.
2. Thoroughly wash machine to remove all dirt, mud,
debris or residue.
3. Check auger, fan and drivelines for damage or
entangled material. Repair or replace damaged
parts. Remove the entangled material.
14. Do not feed snow through snowblower when rais-
ing or lowering.
TRANSPORTING
4. Inspect all hydraulic hoses, fittings, lines and cou-
plers. Tighten any loose fittings. Replace any hose
that is cut, nicked or abraded or is separating from
crimped end of fitting.
„ A minimum 20% of tractor and equipment
weight must be on the tractor front wheels when
5. Change oil in gearbox.
MAN0869 (04/13/2011)
14 Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Lubricate all grease fittings. Make sure that all
grease cavities have been filled with grease to
remove any water residue from washings.
■
Replace any safety decals that are missing or not
readable (supplied free by your Woods dealer). See
Safety Decals section for location drawing.
7. Touch up all paint nicks and scratches to prevent
PRE-OPERATION CHECK LIST
(OWNER'S RESPONSIBILITY)
rusting.
8. Move to storage area.
___ Review and follow all safety rules and safety
decal instructions on pages page 5 through
page 9.
9. Select an area that is dry, level and free of debris.
10. Unhook from tractor (see page 11).
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
11. Store machine in an area away from human activ-
ity.
___ Check that all shields and guards are properly
installed and in good condition. Replace if dam-
aged.
12. Do not allow children to play on or around stored
machine.
CLEANING
___ Check that all hardware and cotter pins are prop-
erly installed and secured.
After Each Use
___ Check that equipment is properly and securely
attached to tractor.
■
Remove large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
Inspect machine and replace worn or damaged
parts.
___ Make sure driveline spring-activated locking pin
or collar slides freely and is seated firmly in trac-
tor PTO spline groove.
■
___ Inspect area and remove stones, branches or
other hard objects that might be thrown, causing
injury or damage.
■
Replace any safety decals that are missing or not
readable.
Periodically or Before Extended Storage
___ Do not allow riders.
___ Check the drive chain for tension. If too loose,
adjust the idler sprocket. A 1/4" sag in the bottom
span is satisfactory.
■
Clean large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
■
Remove remaining debris using a low-pressure
water spray.
1. Be careful when spraying near scratched or torn
___ Check all lubrication points and grease as
instructed in "Service, lubrication information".
Make sure the PTO slip joint is lubricated and
that the gearbox fluid levels are correct.
safety decals or near edges of decals as water
spray can peel decal off surface.
___ Set tractor PTO at correct rpm for your equip-
ment.
2. Be careful when spraying near chipped or
scratched paint as water spray can lift paint.
___ Check that all hydraulic hoses and fittings are in
good condition and not leaking before starting
tractor. Check that hoses are not twisted, bent
sharply, kinked, frayed or pulled tight. Replace
any damaged hoses immediately.
3. If a pressure washer is used, follow the advice
of the pressure washer manufacturer.
■
Inspect machine and replace worn or damaged
parts.
■
Sand down scratches and the edges of areas of
___ Make sure tractor ROPS or ROPS CAB and seat
belt are in good condition. Keep seat belt
securely fastened during operation.
missing paint and coat with Woods spray paint of
matching color (purchase from your Woods dealer).
Operation 15
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER SERVICE
The information in this section is written for operators
who possess basic mechanical skills. Should you need
help, your dealer has trained service technicians avail-
able. For your protection, read and follow all safety
information in this manual.
CAUTION
„ If you do not understand any part of this manual
and need assistance, see your dealer.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
„ Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
SERVICE AND MAINTENANCE
INTERVALS
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
By following a careful service and maintenance pro-
gram, you will prolong the life of your machine.
The service intervals recommended are based on nor-
mal operating conditions. Severe or unusual conditions
may require more frequent service.
„ NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.
Lubrication Information
1. Do not let excess grease collect on or around
parts, particularly when operating in sandy areas.
2. Use a hand-held grease gun for all greasing.
3. Use a lithium grease of #2 consistency with a
MOLY (molybdenum disulfide) additive for all loca-
tions unless otherwise noted. Be sure to clean fit-
tings thoroughly before attaching grease gun.
• Service work does not require going under-
neath implement.
• Read Operator's Manual for service instruc-
tions or have service performed by a qualified
dealer.
4. If grease fitting will not take grease, remove and
clean thoroughly. Also clean lubricant passage
way. Replace fitting if necessary.
„ Before performing any service or maintenance,
disconnect driveline from tractor PTO.
5. Two good pumps of most grease guns is sufficient
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
when the lubrication schedule is followed.
Driveline Lubrication
„
Make sure shields and guards are properly
1. Lubricate the driveline slip joint every 8 hours of
operation. Failure to maintain proper lubrication
could result in damage to u-joints, gearbox, and
driveline.
installed and in good condition. Replace if damaged.
„ Make sure attachment is properly secured,
adjusted, and in good operating condition.
2. Lower snow blower to ground, disconnect driveline
from tractor PTO shaft, and slide halves apart. Do
not disconnect the halves from each other.
„ Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its compo-
nents in any way.
3. Apply a bead of grease completely around male
half where it meets female half. Slide drive halves
over each other several times to distribute grease.
16 Owner Service
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Apply one pump of grease to each driveline u-joint
grease fitting.
5. Apply one pump of grease to each of the plastic
driveline shield bearings.
6. On the shear pin driveline, lubricate the shear yoke
with grease to prevent galling.
7. Periodically check the yokes on the front PTO.
Make sure the bolt and nut are tight and the yoke
is not moving on the gearbox shaft.
Driveline Shear Bolt Replacement
PTO drivelines are equipped with shear bolts to protect
against overloads.
Figure 8. Drive Chain Lubrication
1. Apply grease to drive sprocket grease zerk (See
■
Always use approved shear bolt as replace-
Figure 8).
ment part. Using a hardened bolt or shear pin may
result in damage to driveline or gearbox.
2. Apply grease or oil to the drive chain regularly,
especially after using (See Figure 8).
NOTICE
WARNING
■
Replacement chain should be only high quality
original equipment chain for longer life.
■
Before proceeding, read and follow all safety
rules.
1. Remove jackshaft shield (17) by removing thumb
screws (32).
1. Disconnect driveline from tractor PTO shaft.
2. Loosen cap screw and nut on idler sprocket.
2. Remove gearbox shield by removing thumb
screws.
3. Move idler sprocket (33) to obtain 1/4 inch sag
along bottom span of chain (46).
3. Remove damaged bolt from yoke on input shaft of
snow blower gearbox.
4. Re-tighten idler sprocket and reinstall jackshaft
shield.
4. Rotate driveline to align holes in yoke and shaft.
Install new shear bolt and secure with lock nut.
Tighten to torque specification given on Torque
Chart.
5. Reinstall gearbox shield and reconnect driveline to
tractor PTO shaft.
Chain Maintenance
The auger chain should be inspected every 25 hours.
New chain has a tendency to stretch, so it is necessary
to check the chain tension to prevent flopping around,
thus causing potential problems. Chain tension is pre-
set at the factory. If chain becomes excessively loose,
it may be necessary to readjust the idler sprocket, Fig-
ure 9.
17. Jackshaft Shield
19. Grease Zerk
32. Thumb Screw
33. Idler Sprocket
Figure 9. Auger Drive Chain Adjustment
Owner Service 17
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger Drive Shear Bolt Replacement
Always use approved shear bolt as replace-
ment part. Using a hardened bolt or shear pin may
result in damage to driveline or gearbox.
Gearbox
■
The gearbox is almost maintenance-free, but should be
checked quarterly to be sure that the oil level is main-
tained at half full. A high quality gear oil with a viscosity
index of 80W or 90W and an API service rating of GL-4
or -5 is recommended for use in the gearbox. Oil
should be changed after the first 30 hours or 30 days of
operating. Then, normal change should be adequate.
In the case of seasonal usage, it is best to change the
oil at the end of the season to remove moisture and
corrosive contaminants.
Remove any obstructions from the auger, chain, or
drive sprocket.
Remove jackshaft shield by removing thumb screws.
Remove damaged bolt from shear plates on drive
sprocket and/or jackshaft (18).
Rotate drive sprocket to align holes in sprocket and
shaft. Install new shear bolt (21) and secure with lock
nut (22). Tighten to torque specification given on
Torque Chart.
WARNING
■
Before proceeding, read and follow all safety
rules.
To change the oil, follow this procedure, Figure 12:
1. Suction out oil in gearbox through side plug using a
hand pump.
NOTE: It is best to drain the oil when the gearbox
is warm to remove the most contaminants.
2. Add 0.52 quart SAE 85W90 gear oil through side
plug. Use level hole (halfway up the backside of
gearbox) to check oil level. Add oil accordingly.
3. Install and tighten plug.
18. Auger Drive Shaft
21. 1/4 NC x 1” HHCS GR5
22. 1/4 NC Lock Nut
Figure 10. Auger Drive Shear Bolt Replacement
Discharge Chute Lubrication
Oil Plug
1. Apply grease between the discharge chute base
and ring on the frame tube, Figure 11, annually.
DP8
Figure 12. Gearbox Oil
Skid Shoes
The machine is equipped with skid shoes on bottom
side of each side plate to prevent wearing frame and to
provide depth control. They should be checked occa-
sionally for wear and replaced if required.
WARNING
■
Before proceeding, read and follow all safety
rules.
Figure 11. Chute Base and Rotator Ring
18 Owner Service
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Place a 4" x 4" block under each end of snow-
2. Rotate bell shield until three reliefs align with white
blower frame.
plastic collar.
3. Remove bell housing and shaft.
NOTE: Block only high enough for the skid shoes
to clear ground.
4. Replace components as needed. Follow steps 1
through 3 in reverse.
2. Lower snowblower to sit securely on blocks.
3. Properly secure tractor and release all hydraulic
pressure.
4. Loosen and remove skid shoe mounting bolts (3)
and nuts (31).
5. Remove skid shoe and inspect (4).
6. Adjust skid shoe (4) to provide correct depth of cut.
7. Tighten mounting bolts (3) and nuts (31). Tighten to
specifications given on torque chart.
3. 1/2 NC x 1” Carriage Bolt
4. Skid Shoe
DP7
Figure 14. Walterscheid Driveline
Comer Driveline
31. 1/2 NC Lock Nut
1. Rotate three rectangular plastic pins with a screw
driver 90°.
2. Lift pins out with screw driver.
3. Remove bell housing and shaft.
4. Replace components as needed. Follow steps 1
through 3 in reverse.
Figure 13. Skid Shoe Adjustment
PTO Driveline Guard
The shield must turn freely on PTO shaft. Daily lubrica-
tion of both shield bearings and periodic cleaning will
ensure safe operation of the shield.
If shield is damaged or worn, replace components with
genuine Woods service parts.
Walterscheid Driveline
1. Remove Phillips screw on driveline bell shield.
DP6
NOTE: In order to slide new bell over shaft guard,
place bell in water at 180° F or in sun to expand
bell temporarily.
Figure 15. Comer Driveline
(Rev. 5/19/2011)
Owner Service 19
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
PROBLEM
PROBLEM CAUSES
SUGGESTED SOLUTION
PTO Shaft shear bolt continues
to shear
PTO shaft at too great an angle.
Do not exceed a 15 degree
angle at PTO shaft.
PTO shear bolt is too soft.
Use a grade 5 shear bolt. (GKN)
Use a grade 10.9 bolt. (Comer
20 series)
Use a grade 8.8 bolt. (Comer
40 series)
Tilt on the snowblower is too
great causing an excessive
knuckle angle.
Reduce tilt on snowblower by
adjusting upper 3-point link.
Snowblower augers continue to
plug
Tractor ground speed is too fast.
Insufficient fan speed.
Reduce ground speed to allow
augers to clear better.
Increase tractor PTO speed to
540 RPM.
Snow does not discharge
properly
Insufficient fan speed.
Maintain a PTO speed of 540
RPM.
Augers are overloaded with
snow.
Reduce ground speed.
Snow is wet and sticky.
Reduce ground speed to allow
for better aeration of snow.
Snowblower tends to dig or float
on snow
Tilt on snowblower not adjusted
properly.
Adjust upper link on 3-point to
level the blower.
Skid Shoes not adjusted prop-
erly.
Adjust skid shoes to be even
with cutting edge.
Chute will not turn
Auger fails to turn
Insufficient lubrication.
Lubricate chute base and rotator
ring.
Incorrect number of spacers.
Check that 3 spacers are being
used.
Auger drive shear bolt has
sheared.
Replace auger drive shear bolt.
20 Owner Service
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
5. Remove plug from gearbox and add .52 quart of
DEALER SET-UP INSTRUCTIONS
SAE85W-90 gear oil, Figure 12.
Assembly of this snowblower is the responsibility of the
Woods dealer. It should be delivered to the owner com-
pletely assembled, lubricated and adjusted for normal
conditions.
6. Remove hardware (37) and (38) from SMV bracket
(34) and rotate bracket facing up. Reinstall hard-
ware (37) and (38), Figure 17.
The snowblower is shipped partially assembled.
Assembly will be easier if components are aligned and
loosely assembled before tightening hardware. Rec-
ommended torque values for hardware are located on
page 38.
Select a suitable working area. A smooth hard surface,
such as concrete, will make assembly much quicker.
Open parts boxes and lay out parts and hardware to
make location easy. Refer to illustrations, accompany-
ing text, parts lists and exploded view drawings.
All Models
1. Remove parts from crate in a suitable work area.
Check packing list to ensure all parts are present.
NOTE: Leave all hardware loose until all compo-
nents are completely assembled.
34. SMV Bracket
37. 5/16 NC x 1" Carriage Bolt
38. 5/16 NC Hex Locknut
2. Remove driveshaft from snowblower. Slide imple-
ment PTO shaft on gearbox shaft. Pull back spring
actuated collar as driveline is installed on gearbox
shaft, releasing collar when driveline is installed.
Figure 17. SMV Installation
7. Remove plastic cable tie holding auger chain in
NOTE: Check that drive shaft is fully engaged in
gearbox shaft groove.
place.
Install Hand Crank (Figure 18)
3. Remove hardware (37) and (38) from front right
mast plate hole and rotate drive holder (16) until
holes are aligned, Figure 16.
8. Fasten mount bracket (5) to upper three-point
channel using two carriage bolts (8) and lock nuts
(9).
4. Reinstall hardware (37) and (38).
NOTE: Bracket is adjustable and can be rotated or
slide up or down for best fit with tractor.
9. Connect clevis rotator (1) to block (2) and clevis
tube (3) with roll pins (6).
10. Remove rotator sprocket from lower hitch pin.
Install in square opening on chute adapter with
block and pin assembly using roll pins (6) and (13).
Hole in sprocket rotator should face towards tractor
hitch.
11. Install trim strip (6.5" long) in slot on mount bracket
(5) which hand crank (4) will protrude through.
16. Drive Holder
37. 5/16 NC x 1" Carriage Bolt
38. 5/16 NC Lock Nut
12. Slide hand crank (4) through mount bracket (5)
and into clevis tube (3). Align hand crank and cle-
vis tube holes for correct length and install cap
screws (7) and hex nut (9).
Figure 16. Install Drive Holder
(Rev. 10/4/2011)
Assembly 21
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Make sure handle will not protrude into rear
window of a tractor equipped with cab by checking
the highest 3-point hitch position.
NOTE: Refer to Figure 20 for proper orientation
and installation of hardware.
16. Install two cap screws (5) through front two holes
of discharge chute (8) and discharge chute spac-
ers (35). Secure with nuts (28). Leave hardware
loose.
17. Install six cap screws (27) through discharge chute
clamp (40), discharge chute spacers (35) and dis-
charge chute (8). Secure with nuts (28).
18. Tighten hardware.
19. Operate hand crank to check ease of block and pin
and chute rotation. If hand crank turns too hard,
adjust mounting bracket for a reduced angle. If
chute does not rotate freely check spacers and
chute hardware for binding.
1. Clevis Rotator
2. Block
3. Clevis Tube
11. 3/8 Lock Washer
12. 3/8 NC x 1 HHCS
13. 5/16 x 1-3/4 Roll Pin
14. Trim Strip 6.5"
4. Hand Crank
5. Mount Bracket
6. 5/16 x 2 Roll Pin
7. 5/16 NC x 1-1/2 HHCS
8. 5/16 NC x 1 Carriage Bolt
9. 5/16 NC Lock Nut
10. Rotator Shield
Figure 18. Hand Crank Installation
13. Apply grease to discharge tube ring and frame.
5. 3/8 NC x 1-1/2 HHCS GR5
8. Discharge Chute
Figure 19. Apply Grease to Discharge Chute Ring
27. 3/8 x 1-1/4 HHCS GR5
28. 3/8 NC Hex Locknut
35. Discharge Chute Spacer
40. Discharge Chute Clamp
14. Loosen discharge chute hardware and remove
washers. Washers will not be reused.
Install Discharge Chute (Figure 20)
15. Attach discharge chute (8) to chute base using
spacers (35), (6 total, 3 each side), discharge
chute clamp (40), and hardware.
Figure 20. Install Discharge Chute
(Rev. 10/4/2011)
22 Assembly
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Remove rotator sprocket from lower hitch pin.
Position rotator sprocket in square opening on
chute adapter with hole facing towards hitch. Slide
hydraulic motor and channel assembly into rotator
sprocket and fasten using roll pin.
MOUNTING HYDRAULIC CHUTE ROTA-
TOR OPTION (FIGURE 22)
1. Fasten coupler (7) to hydraulic motor (1) using
woodruff key and set screw (8).
6. Fasten flow restrictors (2) to hydraulic motor.
7. Fasten hydraulic hose (3) to restrictors (2).
8. Fasten couplers (4) to ends of hoses (3).
2. Fasten hydraulic motor assembly to hydraulic
motor mount bracket (6) using cap screws (15) and
lock washers (16).
3. Fasten hydraulic motor coupler (7) to shaft rotator
(10) using roll pin (9).
4. Fasten hydraulic motor mount to upper three-point
channel with cap screws (17), link (11), and hex
nuts (18).
17. 3/8 NC x 4 HHCS
18. 3/8 NC Locknut
9. Roll Pin
1. Hydraulic Motor
2. Restrictor
3. Hydraulic Hose
4. Coupler
10. Shaft Rotator
11. Mounting Link
13. 3/8 x 3/4 crew
15. 3/8 NC x 1" HHCS
16. 3/8 Lock Washer
17. 3/8 NC x 4 HHCS
18. 3/8 NC Locknut
36. Rotator Sprocket
5. Decal
6. Mounting Bracket
7. Coupler
8. Set Screw
Figure 21. Motor Mount Position 8" from Front
Figure 22. Hydraulic Chute Rotator Installation
Assembly 23
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUINTING HYDRAULIC CHUTE DEFLEC-
TOR (FIGURE 25)
12. 3/8 NC x 4 HHCS
13. 3/8 NC Locknut
1. Fasten cylinder (1) to discharge chute (8) using
hardware (6) and (7). Do not over tighten.
2. Fasten elbows (4) to cylinder (1).
3. Fasten hoses (8) to elbows (4).
4. Fasten adapters (5) to hoses (8).
5. Fasten restrictor (3) to adapter (5).
6. Fasten couplers (2) to adapter (5) and restrictor
(3).
Figure 24. Motor Mount Position 6.62" from Front
4. Fasten coupler (4) to shaft (7) with roll pin (6).
5. Slide rotary actuator and channel assembly into
coupler (4) and attach with roll pin (6). Tighten
loose hardware.
Install Wiring Harness
6. Attach connector "A" to the rotary actuator (1), (12"
long from splice).
NOTE: Attach connector "B" to linear actuator on
deflector, if equipped, (36" long from splice).
1. Hydraulic Cylinder
2. Male Coupler
3. Swivel Restrictor
4. Elbow
7. Tie the wire harness away from movable parts and
pinching points using cable ties (5).
5. 1/2 NPTF x 1/2 NPTM Adapter
6. 3/8 NC Lock Nut
7. 3/8 NC x 1-3/4 HHCS
8. 1/4 Hydraulic Hose
Figure 23. Hydraulic Chute Deflector Installation
MOUNTING ELECTRIC CHUTE ROTATOR
OPTION (FIGURE 25)
1. Remove rotator sprocket from lower hitch pin.
Position rotator sprocket in square opening on
chute adapter with hole facing towards hitch. Install
shaft (7) into rotator sprocket (36) using roll pin (6).
Make sure second hole on shaft is facing towards
hitch.
1. Hydraulic Motor
2. Wire Harness
3. Mounting Bracket
4. Coupler
8. Mounting Link
9. Spring Nut
10. Thumb Screw
11. Rotator Shield
12. 3/8 NC x 4 HHCS
13. 3/8 NC Lock Nut
36. Rotator Sprocket
2. Fasten rotary actuator (1) to mounting bracket (3)
using hardware from actuator.
5. Cable Tie
6. Roll Pin
7. Shaft Rotator
3. Fasten mounting bracket (3) and actuator (1) to
upper three point channel using cap screws (12),
link (8), and nuts (13). Leave hardware loose (See
Figure 24).
Figure 25. Electric Chute Rotator Installation
24 Assembly
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNTING ELECTRIC CHUTE DEFLEC-
TOR (FIGURE 26)
1. Install remote deflection option by fastening actua-
tor (14) using cap screws (15) and nuts (16). Do
not over tighten hardware.
5. Cable Tie
14. Actuator
15. 1/4 NC x 1-1/2 HHCS
16. 1/4 NC Lock Nut
Figure 26. Electric Chute Deflector Installation
2. Attach control box in tractor operator area. Attach
end to a power source and ground on the tractor,
(see tractors operator’s manual).
Assembly 25
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
DEALER CHECK LISTS
PRE-DELIVERY CHECK LIST
(Dealer Responsibility)
Inspect the equipment thoroughly after assembly to
ensure it is set up properly before delivering it to the
customer.
DELIVERY CHECK LIST
(Dealer Responsibility)
___ Show customer how to make adjustments and
select proper PTO speed.
___ Instruct customer how to lubricate and explain
importance of lubrication.
The following check lists are a reminder of points to
inspect. Check off each item as it is found satisfactory
or after proper adjustment is made.
___ Point out the safety decals. Explain their meaning
and the need to keep them in place and in good
condition. Emphasize the increased safety haz-
ards when instructions are not followed.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Check that shields and guards are properly
installed and in good condition. Replace if dam-
aged.
___ Present Operator's Manual and request that cus-
tomer and all operators read it before operating
equipment. Point out the manual safety rules,
explain their meanings and emphasize the
increased safety hazards that exist when safety
rules are not followed.
___ Check all bolts to be sure they are tight.
___ Check that all cotter pins and safety pins are
properly installed. Replace if damaged.
___ Check and grease all lubrication points as identi-
fied in "Service, lubrication information".
___ Show customer how to make sure driveline is
properly installed and that spring-activated lock-
ing pin or collar slides freely and is seated in
groove on tractor PTO shaft.
___ Check the level of gearbox fluids before delivery.
Service, if required, as specified in the "Service,
lubrication information."
___ Explain to customer the potential crushing haz-
ards of going underneath raised equipment.
Instruct customer that service work does not
require going underneath unit and never to do so.
___ Point out the correct mounting and routing of
hydraulic hoses. Explain that during operation,
mounting, dismounting and storage, care must be
taken to prevent hose damage from pulling, twist-
ing and kinking.
___ Show customer the safe, proper procedures to be
used when mounting, dismounting, and storing
equipment.
___ For mounted units, add wheel weights, ballast in
front tires, and/or front tractor weight to enhance
front end stability. A minimum 20% of tractor and
equipment gross weight must be on front tractor
wheels. When adding weight to attain 20% of
tractor and equipment weight on front tractor
wheels, you must not exceed the ROPS weight
certification. Weigh the tractor and equipment. Do
not estimate!
___ Make customer aware of optional equipment
available so that customer can make proper
choices as required.
___ Point out all guards and shields. Explain their
importance and the safety hazards that exist
when not kept in place and in good condition.
26 Dealer Check Lists
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS INDEX
SB54S, SB64S, SB74C & SB84C
SNOWBLOWER
SB54S & SB64S ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 - 29
SB74C & SB84C ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 - 31
HAND CRANK ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
GEARBOX ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DRIVE ASSEMBLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 - 35
HYDRAULIC CHUTE ROTATOR & DEFLECTOR (OPTIONAL) . . . . . . . . . 36
ELECTRIC REMOTE CHUTE ROTATOR & DEFLECTOR (OPTIONAL). . . 37
Parts 27
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
SB54S, SB64S SUBCOMPACT SNOWBLOWER ASSEMBLY
(Rev. 10/4/2011)
MAN0869 (04/13/2011)
28 Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
SB54S, SB64S SUBCOMPACT SNOWBLOWER PARTS LIST
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
1/2 Flat Washer
1
2
1033318
1
3
4
2
3
2
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
3
3
4
1
2
1
Fan
30
31
32
3598 *
765 *
1033294
3
5
3
1
1
6
1
6
6
1
1
1
1
1
1
4
1
1
1
1
1
1033190
29893 *
Bearing
1/2 NC Lock Nut
3
1/2 NC x 1-1/2 Carriage Bolt
Skid Shoe
3/8 x 3/4 Thumb Screw
Idler Bearing
4
1033313
976 *
33 90311033
5
3/8 NC x 1-1/2 HHCS GR5
CAT 1 Drawbar Pin
3/8 x 1-3/4 Pin
34
35
1033263
1033286
SMV Bracket
6
SU105
Discharge Chute Spacer
Sprocket Rotator
7
90025028
1033346
1033339
1002018
1026530
1033298
1033291 *
1033222
1033312
36 12020256
8
Discharge Chute
37
38
39
40
41
51243 *
6778 *
5/16 NC x 1" Carriage Bolt GR5
5/16 NC Lock Nut
5/16 x 5/16 x 1-3/4 Key
Discharge Chute Clamp
3/8 Lock Washer
9
Deflector Handle
10
11
13
14
15
16
Sleeve, .81 x 1-1/4 x 2-1/8
Manual Tube
24549
1033317
838 *
Gearbox Shield
3/8 NC x 5-1/2 HHCS GR5
Gearbox
42 103329554
42 103329564
Auger - SB54S
Auger - SB64S
Drive Holder
43
44
45
46
47
48
49
50
24611
839 *
SMV Sign
17 103329754
17 103329764
18 103321454
18 103321464
Jackshaft Shield - SB54S
Jackshaft Shield - SB64S
Auger Drive Shaft - SB54S
Auger Drive Shaft - SB64S
1/4-28 Straight Grease Fitting
Drive Sprocket
3/8 NC x 1" HHCS GR5
Sprocket
1033213
1033277
1033977
33677
Chain
Safety Decal Set
19
20
21
22
23
24
25
26
27
28
29
12296 *
1033211
10378 *
6128 *
Washer, 1/2 x 1-9/16 x 10 GA
Model Decal Set - SB54S & SB64S
1033956
1/4 NC x 1 HHCS GR5
1/4 NC Lock Nut
565 * A/R Washer, 3/8 Flat (SN 1188497 &
Below)
51
73163 *
2
Nut, Whiz 5/16 NC Flange
1033293
31207 *
2864 *
3/8 Spring Nut
3/4 NC x 4 HHCS GR5
3/4 Flat Washer
HHCS
*
Hex Head Cap Screw
Standard Hardware - Obtain Locally
As Required
2371 *
3/4 NC Lock Nut
A/R
12169 * 19 3/8 NC x 1-1/4 HHCS GR5
6698 * 29 3/8 NC Lock Nut
24576 *
1
1/2 NC x 1-3/4 HHCS GR5
(Rev. 9/8/2011)
MAN0869 (04/13/2011)
Parts 29
Download from Www.Somanuals.com. All Manuals Search And Download.
SB74C, SB84C COMPACT SNOWBLOWER ASSEMBLY
(Rev. 10/4/2011)
30 Parts
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
SB74C, SB84C COMPACT SNOWBLOWER PARTS LIST
REF
PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
1
2
1033218
1033190
29893 *
1033226
976 *
1
3
4
2
3
2
4
2
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
3
3
4
1
2
1
Fan
28
29
30
31
32
6698 * 29 3/8 NC Lock Nut
Bearing
24576 *
3598 *
1
3
5
3
1
1
6
1
6
6
1
1
1
1
1
1
4
1
1
1
1
1
1/2 NC x 1-3/4 HHCS GR5
1/2 Flat Washer
3
1/2 NC x 1-1/2 Carriage Bolt
Skid Shoe
4
765 *
1/2 NC Lock Nut
5
3/8 NC x 1-1/2 HHCS GR5
Pin
1033294
3/8 x 3/4 Thumb Screw
Idler Bearing
6
HBL233
27542
33 90311033
6A
6B
7
Klik Pin
34
35
1033263
1033253
SMV Bracket
56598
Sleeve
Discharge Chute Spacer
Sprocket Rotator
90025028
1033246
1033239
1002018
1026530
1033298
1033291 *
1033222
1033227
3/8 x 1-3/4 Pin
36 12020256
8
Discharge Chute
Deflector Handle
Sleeve, .81 x 1-1/4 x 2-1/8
Manual Tube
37
38
39
40
41
51243 *
6778 *
5/16 NC x 1" Carriage Bolt GR5
5/16 NC Lock Nut
5/16 x 5/16 x 1-3/4 Key
Discharge Chute Clamp
3/8 Lock Washer
9
10
11
13
14
15
16
24549
1033278
838 *
Gearbox Shield
3/8 NC x 5-1/2 HHCS GR5
Gearbox
42 103319574
42 103319584
Auger - SB74C
Auger - SB84C
Drive Holder
43
44
45
46
47
48
49
50
24611
839 *
SMV Sign
17 103329774
17 103329784
18 103321474
18 103321484
Jackshaft Shield - SB74C
Jackshaft Shield - SB84C
Auger Drive Shaft - SB74C
Auger Drive Shaft - SB84C
1/4-28 Straight Grease Fitting
Drive Sprocket
3/8 NC x 1" HHCS GR5
Sprocket
1033213
1033244
1033977
33677
Chain
Safety Decal Set
19
20
21
22
23
24
25
26
27
12296
1033211
10378 *
6128 *
Washer, 1/2 x 1-9/16 x 10 GA
Model Decal Set - SB74C & SB84C
1033957
1/4 NC x 1 HHCS GR5
1/4 NC Lock Nut
565 * A/R Washer, 3/8 Flat (SN 1188497 &
Below)
51
73163 *
2
Nut, Whiz 5/16 NC Flange
1033293
31207 *
2864 *
3/8 Spring Nut
3/4 NC x 4 HHCS GR5
3/4 Flat Washer
HHCS
*
Hex Head Cap Screw
Standard Hardware - Obtain Locally
As Required
2371 *
3/4 NC Lock Nut
A/R
12169 * 19 3/8 NC x 1-1/4 HHCS GR5
HAND CRANK ASSEMBLY
REF PART
QTY
DESCRIPTION
Rotator Shaft
Block
1
2
3
4
5
6
7
8
9
1033342
1033345
1033340
12030315
1033284
481757
1
1
1
1
1
2
1
2
3
1
1
1
1
1
Clevis and Tube Assembly
Hand Crank
Handle Mount
5/16 x 2 Roll Pin
24408 *
51243 *
6778 *
5/16 NC x 1-1/2 HHCS GR5
5/16 NC X 1 HHCS GR5
5/16 NC Hex Nut
10 1033299
Shield Rotator
11
12
13
838 *
3/8 Lock Washer
839 *
41
3/8 NC x 1 HHCS GR5
5/16 x 1-3/4 Roll Pin
Trim Strip, 6.5" Long
14 1033774
HHCS
*
Hex Head Cap Screw
Standard Hardware, Obtain Locally
(Rev. 10/4/2011)
MAN0869 (04/13/2011)
Parts 31
Download from Www.Somanuals.com. All Manuals Search And Download.
GEARBOX ASSEMBLY
REF PART
QTY
DESCRIPTION
Ball Bearing
1
2
3
4
5
6
7
8
9
438
4
3
4
8
8
1
1
1
1
20901
1007866
307126
Seal
Shim Pack
M8 x 55 Socket Head Cap Screw
M8 Hex Nut
30515
1007859
1033764
1033765
1033766
External Circlip, 35 x 1.5
Spacer
Key
Gasket and Plug
32 Parts
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
1031908 - COMER SHEAR BOLT DRIVE ASSEMBLY (OPTIONAL)
SB54S, SB64S
REF
PART
QTY
DESCRIPTION
A
1
1031908
1032411
41534
1
1
2
1
6
1
2
1
1
1
1
1
1
1
1
1
1
1
1
Complete 540 driveline and shear bolt assembly
Complete collar yoke C12 1-3/8
Cross & bearing kit
Collar, outer tube
2
3
37167
4
30922
Shield retainer
5
37172
Collar, inner tube
6
30917
Shield tether chains
Yoke, inner tube
7
1032414
1032415
1032416
1032428
1032429
1032430
30913
8
Flexible pin
9
Inner profile tube
10
11
12
13
14
15
16
17
18
Shear yoke assembly
Bolt and Nut M6 x 40 cl 10.9
Grease fitting
1-3/8 Push pin set
Yoke, outer tube
1032423
1001305
1032425
1025873
1001340
Flexible pin
Outer profile tube
Complete shield kit
Lock collar repair kit
Parts 33
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
1031826 - COMER SHEAR BOLT DRIVE ASSEMBLY (OPTIONAL)
SB74C, SB84C
REF
PART
QTY
DESCRIPTION
A
1
1031826
1001300
38478
1
1
2
1
6
1
2
1
1
1
1
1
1
1
1
1
1
1
1
Complete 540 driveline and shear bolt assembly
Complete collar yoke C12 1-3/8
Cross & bearing kit
Collar, outer tube
2
3
1019442
30922
4
Shield retainer
5
1019444
30917
Collar, inner tube
6
Shield tether chains
Yoke, inner tube
7
1001306
1001305
30928
8
Flexible pin
9
Inner profile tube & yoke
Shear yoke assembly
Bolt and Nut M8 x 50 cl 8.8
Grease fitting
10
11
12
13
14
15
16
17
18
1032435
1032436
1032430
30913
1-3/8 Push pin set
1001301
1001302
30926
Yoke, outer tube
Flexible pin
Outer profile tube & yoke
Complete shield kit
Lock collar repair kit
1021552
1001340
(Rev. 10/4/2011)
34 Parts
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
1033266- WALTERSCHEID DRIVE ASSEMBLY (OPTIONAL)
SB54S, SB64S, SB74C, SB84C
REF PART
QTY
DESCRIPTION
Complete 540 Driveline Assembly
A
1
1033266
38498
1
1
2
1
2
1
1
1
1
2
2
1
2
1
1
1
1
1
Yoke Assembly
2
38478
Cross Bearing Kit
3
415147
415146
40587
Inboard Yoke
4
Spring Pin
5
Inner Profile
6
40588
Outer Profile
7
1029940
1029941
40766
Inboard Yoke
8
Shearbolt Clutch
10
13
16
Bearing Ring
40778
Screw, M3.5 x 10 mm
40777
Chain
17 1029932
18 1029943
19 1029942
Collar
Kit - Outer Guard Complete (includes items 9, 10, 11, 13, 14 & 17)
Kit - Inner Guard Complete (includes items 9, 10, 12, 13, 16 & 17)
Collar Repair Kit
20
40589
21 1005784
22 1032436
Quick Disconnect Pin Kit
M8 x 50 CL 8.8, Shear Bolt & Nut
(Rev. 12/6/2011)
Parts 35
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC CHUTE ROTATOR
(OPTIONAL)
HYDRAULIC CHUTE DEFLECTOR
(OPTIONAL)
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
Hydraulic Motor
1
2
3
4
5
6
7
8
1033300
66511
1
2
1
2
2
2
2
2
Hydraulic Cylinder 1 x 3 x 7.75
1/2 NPT Male Coupler
1/2" Swivel Restrictor
1
2
3
4
5
6
7
8
9
90405236
90519159
90519160
64332
1
2
2
2
1
1
1
1
2
1
1
2
2
1
4
4
2
2
.031 x 6MJIC 10MORG Restrictor
3/8 x 6JICF x 8 MORB Hose, 54"L
Male Quick Coupler
90501531
8572
1/4 Elbow
11893
1/4 NPTF x 1/2 NPTM Adapter
3/8 NC Lock Nut
1033603
1033611
10430071
301605 *
41
Decal, WRNG - Hydraulic Pressure
Motor Mount Channel
Motor Coupler
6698 *
920 *
3/8 NC x 1-3/4 HHCS GR5
1/4 Hose, 1/4MP x 1/4MP, 101"L
21020219
5/16 NC x 3/8 SHSS
5/16 x 1-3/4 Roll Pin
Shaft Rotator
HHCS
*
Hex Head Cap Screw
10 1033613
11 1033614
12 1033293
13 1033294
14 1033737
Standard Hardware, Obtain Locally
Mounting Link
3/8 -16 U-Tapped Spring Nut
3/8 x 3/4 Thumb Screw
Safety Shield
15
16
17
18
839 *
3/8 NC x 1 HHCS GR5
3/8 Lock Washer
838 *
14478 *
6698 *
3/8 NC x 4 HHCS GR5
3/8 NC Lock Nut
HHCS
SSHS
*
Hex Head Cap Screw
Socket Head Set Screw
Standard Hardware, Obtain Locally
36 Parts
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRIC CHUTE ROTATOR (OPTIONAL)
REF PART
QTY
DESCRIPTION
Rotary Actuator
REF PART
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
12030819
12030802
1033611
10430071
88
1
1
1
1
2
3
1
1
2
10 1033294
11 1033736
2
1
2
2
1
3/8 x 3/4 Thumb Screw
Rotator Shield
Wiring Harness
Motor Mount
12
13
14478 *
6698 *
3/8 NC x 4 HHCS GR5
3/8 NC Lock Nut
Motor Coupling
Plastic Tie (Ty-Rap) 3/16 x 14-1/4
5/16 x 1-3/4 Roll Pin
Shaft, Hydraulic Rotator
Mounting Link
36 12020256
Sprocket Rotator
41
1033613
1033614
1033293
HHCS
*
Hex Head Cap Screw
Standard Hardware - Obtain Locally
3/8-16 U-Tapped Spring Nut
ELECTRIC CHUTE DEFLECTOR (OPTIONAL)
REF PART
QTY
DESCRIPTION
REF PART
HHCS
QTY
DESCRIPTION
Hex Head Cap Screw
5
88
1
1
1
2
Plastic Tie (Ty-Rap) 3/16 x 14-1/4
Linear Actuator
14 1033727
15
16
62788 *
6128 *
1/4 NC x 1-1/2 HHCS GR5
1/4 NC Lock Nut
*
Standard Hardware, Obtain Locally
Parts 37
MAN0869 (04/13/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
SAE 2
SAE 5
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
8
lbs-ft
10
N-m
13
lbs-ft
14
N-m
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
7/16"
1/2"
6
18
37
12
17
19
26
27
9/16"
5/8"
23
31
35
47
49
67
36
48
55
75
78
106
163
232
325
569
907
1383
3/4"
55
75
85
115
164
230
403
642
979
120
171
240
420
669
1020
13/16"
15/16"
1-1/8"
1-5/16"
1-1/2"
78
106
149
261
416
634
121
170
297
474
722
110
192
306
467
METRIC SERIES
TORQUE
CHART
8.8
Metric Bolt Head
Identification
10.9
A
Metric
Grade 8.8
Metric
Grade 10.9
COARSE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
FINE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
A
A
Diameter &
Thread Pitch Wrench
(Millimeters)
Diameter &
Thread Pitch
(Millimeters)
Size
N-m
lbs-ft
6
N-m
lbs-ft
6
6 x 1.0
10 mm
13 mm
16 mm
18 mm
21 mm
24 mm
27 mm
30 mm
34 mm
36 mm
46 mm
8
11
27
8
8
11
29
8
6 x 1.0
8 x 1.0
8 x 1.25
10 x 1.5
12 x 1.75
14 x 2.0
16 x 2.0
18 x 2.5
20 x 2.5
22 x 2.5
24 x 3.0
30 x 3.0
20
15
20
21
16
22
39
29
54
40
41
30
57
42
10 x 1.25
12 x 1.25
14 x 1.5
16 x 1.5
18 x 1.5
20 x 1.5
22 x 1.5
24 x 2.0
30 x 2.0
68
50
94
70
75
55
103
163
250
363
507
684
861
1740
76
109
169
234
330
451
571
1175
80
151
234
323
457
623
790
1626
111
173
239
337
460
583
1199
118
181
263
367
495
623
1258
87
120
184
268
374
505
635
1283
125
172
244
332
421
867
133
194
270
365
459
928
Typical Washer
Installations
Bolt
Flat Washer
Lock Washer
8/9/00
Bolt Torque & Size Charts (Rev. 3/28/2007)
38 Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
5/8
3/4
7/8
IN
1
2
7
3
4
5
6
MM
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM 10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG .............................................................. Agriculture
MPa.........................................................Mega Pascal
N.......................................................................Newton
NC......................................................National Coarse
NF ...........................................................National Fine
NPSM.....................National Pipe Straight Mechanical
NPT.......................................... National Pipe Tapered
NPT SWF .........National Pipe Tapered Swivel Female
ORBM .......................................... O-Ring Boss - Male
P...........................................................................Pitch
PBY...................................................... Power-Beyond
psi..........................................Pounds per Square Inch
PTO..................................................... Power Take Off
QD....................................................Quick Disconnect
RH..............................................................Right Hand
ROPS........................... Roll-Over Protective Structure
RPM ........................................Revolutions Per Minute
RT ....................................................................... Right
SAE..........................Society of Automotive Engineers
UNC .....................................................Unified Coarse
UNF...........................................................Unified Fine
UNS......................................................Unified Special
ASABE.................... American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE ....... American Society of Agricultural Engineers
ATF ............................... Automatic Transmission Fluid
BSPP .............................British Standard Pipe Parallel
BSPTM ................British Standard Pipe Tapered Male
CV.....................................................Constant Velocity
CCW .............................................. Counter-Clockwise
CW............................................................... Clockwise
F ...................................................................... Female
FT .............................................................. Full Thread
GA .................................................................... Gauge
GR (5, etc.) ........................................... Grade (5, etc.)
HHCS ........................................Hex Head Cap Screw
HT........................................................... Heat-Treated
JIC .................Joint Industry Council 37° Degree Flare
LH.................................................................Left Hand
LT........................................................................... Left
m......................................................................... Meter
mm................................................................Millimeter
M.......................................................................... Male
Bolt Torque & Size Charts (Rev. 3/28/2007)
Appendix 39
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
All Models Except Mow’n MachineTM Zero-Turn Mowers
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
Model Number: ____________________________
From (Dealer): __________________________________________
Serial Number: __________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth
below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Duration (from date of
delivery to the original
purchaser)
Model Number
Gearbox
Seals
All units listed below
2 years
BW1260, BW1620, BW1800, BW2400
8 years
7 years
BW240HD, BW180HD, BW180HB, BW126HB
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X,
DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240
6 years
Gearbox
components PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2, RM660-2,
RD990X, PRD6000, PRD7200, PRD8400, S15CD, S20CD, S22CD, S25CD, S27CD, BW180LH, 5 years
TC/R74, TC/R68, TC/R60, TBW144, TBW180, TBW204
3 years (1 year if used in rental or
commercial applications)
RDC54, RD60, RD72, TBW150C, TS/R60, TS/R52, TS/R44
Blade
spindles
RM550-2, RM660-2, RD990X, PRD6000, PRD7200, PRD8400, TBW144, TBW180, TBW204
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW126HB, BW180-3, BW180HB,
3 years
Rust-through BW180HD, BW1260, BW1800, BW240, BW240HD, 2162, 3240, DS1260, DSO1260, DS1440, 10 years
TS1680
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially
modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center.
This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made with parts other
than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to a
third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS, in
its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of
purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY.
THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues
or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or
rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, its
authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this
Warranty. Answers to any questions regarding warranty
service and locations may be obtained by contacting:
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
F-3079 (Rev. 2/14/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(Replacement Parts For All Models Except Mow’n Machine
TM
Zero-Turn Mowers)
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-8494 (Rev. 10/3/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN0826
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
815-732-2141 tel
815-732-7580 fax
© 2011 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|