111877
LOADER MOUNTING KIT
for 1020, 1027, LU126 Loaders
®
on Ford/New Holland
2000, 2310, 2600, 2610
2810, 2910, 3000, 3600
3610, 3910, 4000SU, 4100
4600SU, 4610SU, Tractors
includes Hose Kits
57923, 1001420
1023582, 1023596
Tested. Proven. Unbeatable.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
must be surgically removed as soon as possible by
!
a doctor familiar with this form of injury or gan-
LEA EL INSTRUCTIVO!
grene, serious injury, or death will result. CON-
Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
„ Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
„ Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
In addition to the design and configuration of
equipment, hazard control and accident preven-
tion are dependent upon the awareness, con-
cern, judgement, and proper training of
personnel involved in the operation, transport,
maintenance, and storage of equipment.
„ Protective hose sleeves must cover all hydrau-
lic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
It has been said, “The best safety device is an
informed, careful operator.” We ask you to be
that kind of operator.
INSTALLATION
„ Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
„ This Loader Mounting Kit is to be used only for
the loaders and tractors specified in this manual.
Any other use or modification of this mounting kit
may result in serious injury or death.
„ Hydraulics must be connected as instructed in
this manual. Do not substitute parts, modify, or
connect in any other way.
„ After connecting hoses, check that all control
lever positions function as instructed in the Opera-
tor's Manual. Do not put into service until control
lever and equipment movements are correct.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
„ Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its compo-
nents in any way.
„ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
„ Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
„ Use a suitable lifting device of sufficient capac-
ity. Use adequate personnel to handle heavy com-
ponents.
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
„ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
Loader Mounting Kit SR3 (4/25/2003)
Safety 3
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADER MOUNT INSTALLATION
CAUTION
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
■
Only use 111877 Loader Mounting Kit for
mounting Woods 1020, 1027, LU126 loaders on
Ford New Holland 2000, 2310, 2600, 2610, 2810,
2910, 3000, 3600, 3610, 3910, 4000SU, 4100,
4600SU, and 4610SU tractors. Any other use or
modification of this mounting kit may result in seri-
ous injury or death.
NOTICE
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
■
This equipment must be assembled and
installed on the customer’s tractor by the Woods
dealer. Dealer must thoroughly inspect equipment
and complete each item on the PRE-DELIVERY
CHECK LIST, DELIVERY CHECK LIST, and PROD-
UCT REGISTRATION before equipment is released
to the customer.
■
Clean threaded holes in the tractor chassis
thoroughly using a tap of the proper size. Paint,
rust, or debris in the threads may not permit cap
screws to be installed and tightened correctly.
TRACTOR PREPARATION
For installing this mounting kit, references to right, left,
forward, and rearward directions are determined from
the operator’s position in the tractor seat.
NOTE: Leave all loader mount hardware loose until
mount is completely installed or otherwise instructed.
1. Shut off engine and set parking brake during
installation.
2. Remove the tractor front weights and weight
bracket if equipped.
3. Set tractor front wheel width to 61-1/2” (center
line of thread) as instructed in tractor operator
manual.
4. Remove cowl-mounted headlights if equipped.
As a valued customer, Woods appreciates your comments. Once loader mount and
hydraulic hoses have been installed, please take a few minutes to complete the Loader
Mount Evaluation sheet that was supplied with your loader mount. Your comments will
help us continue to bring you quality products.
MAN0064 (Rev. 7/20/2007)
4 Mount Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Right and Left Rear Mounts
1. 1026490 Right rear mount
2. 1026491 Left rear mount
1. Attach right rear mount (1) to the tractor clutch
housing using two cap screws (12) and hardened
flat washers (14) in the top holes and two cap
screws (16) hardened flat washers (14) in the
lower two holes.
12. 300517 3/4 NC x 1-3/4 HHCS GR5
14.
16.
57798 3/4 Hardened flat washer
735 3/4 NC x 2 HHCS GR5
2. Repeat to install left rear mount (2).
14
12
DP1
14
16
Figure 2. Left rear Mount Installed
Figure 1. Rear Mount Installation
(Rev. 05/18/2010)
MAN0064 (Rev. 7/20/2007)
Mount Installation 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Front Mount
1. Insert four (two per side) carriage bolts (13) into
upper holes of front mount prior to attaching to
tractor. Carriage bolts should be inserted from the
inside pointing outward.
13
2. Attach front support (3) to tractor, using two cap
screws (17) and hardened flat washers (15).
3. 1001642 Front mount
13. 301130 5/8 NC x 1-1/2 Carriage bolt GR5
15.
17.
57817 5/8 Hardened flat washer
902 5/8 NC x 2 HHCS GR5
15
17
DP2
Figure 3. Front Mount Installed
Install Right and Left Side rails
1. Place front holes of right side rail (4) over carriage
bolts (13) and front mount and secure with hard-
ened flat washers (15) and hex nuts (10).
2. Attach side rail to inside of rear mount, using four
carriage bolts (13), hardened flat washers (15)
and hex nuts (10).
Carriage bolts must be installed with heads on inside
of rear mount as shown in Figure 6.
3. Repeat steps to install left side rail (5).
4. 1026492 Right side rail
5. 1026493 Left side rail
10.
230 5/8 NC Hex nut
Figure 4. Right Side Rail Installation
13. 301130 5/8 NC x 1-1/2 Carriage bolt GR5
15.
57817 5/8 Hardened flat washer
13
15
13
15
10
10
DP4
DP3
Figure 5. Side Rail to Front Mount
Figure 6. Side Rail to Rear Mount
(Rev. 05/18/2010)
MAN0064 (Rev. 7/20/2007)
6 Mount Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Grill Guard (Optional)
Attach grill guard (21) to front mount (3) using four
(two per side) cap screw (23), lock washers (25),
hardened flat washers (24) and hex nuts (22).
Torque hardware to: . . . . . . . .85 lbs-ft (115 N-m)
3. 1001642 Front mount
21.
22.
23.
24.
25.
57822 Grill guard
1093 1/2 NC Hex nut
3379 1/2 NC x 1-1/2 HHCS GR5
57816 1/2 Hardened flat washer
855 1/2 Lock washer
Figure 7. Grill Guard Installation
Torque Hardware
Torque all hardware to specifications listed below.
TORQUE SPECIFICATIONS
Wrench
Ref
12
13
16
17
Cap Screw
Qty
Size
Required Torque
297 lbs.-ft. (403 N-m)
170 lbs.-ft. (230 N-m)
297 lbs.-ft. (403 N-m)
170 lbs.-ft. (230 N-m)
3/4 NC x 1-3/4
4
1-1/8”
15/16”
1-1/8”
15/16”
5/8 NC x 1-1/2 (Carriage Bolt)
3/4 NC x 2
12
4
5/8 NC x 1-1/2
2
MAN0064 (Rev. 7/20/2007)
Mount Installation 7
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MAN0064 (Rev. 7/20/2007)
8 Mount Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
HOSE KIT INSTALLATION
„ Keep hands and body away from pressurized
„ Protective hose sleeves must cover all hydrau-
lic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
„ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
grene, serious injury, or death will result. CON-
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
„ Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
„ Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
57923 Hose Kit Installation - - - - - - - - - - - - - - page 9
1001420 Hose Kit Installation- - - - - - - - - - - - page 12
1023582 Hose Kit Installation- - - - - - - - - - - - page 16
1023596 Hose Kit Installation- - - - - - - - - - - - page 19
57923 HOSE KIT
General Description
Install Hose Fittings
These instructions are for operating the 1020/1027
loader using the tractor hydraulic remote control lever.
To use this hydraulic connection, the tractor must be
equipped with two hydraulic levers and four tractor
hydraulic couplers.
1. Attach elbow (2) and male quick coupler (3) to
each loader supply hose (1).
2. Connect loader supply hoses to loader steel
feedlines following pattern shown in Figure 8.
1.
2. 313053 Elbow, 3/4 JICF x 1/2 NPTM
3. 66511 Quick coupler, male 1/2
57912 Hose, 120" x 1/2 JICM x JICM
NOTE: Male quick couplers (3) for connection to trac-
tor are NOT included with the hose kit but are avail-
able as service parts.
Figure 8. 1020/1027 Loader Supply Hose Connection
MAN0064 (Rev. 7/20/2007)
Hydraulic Installation 9
Download from Www.Somanuals.com. All Manuals Search And Download.
59723 Hose Kit
Route Hydraulic Hoses
/()7 6,'(
+<'5$8/,&
&21752/
5,*+7 6,'(
+<'5$8/,&
&21752/
Route hoses along loader mount, under the right side
of the operator’s platform, and over the rear axle.
%
'
Be sure to avoid contact with 3-point linkage, brake
pedals, and other moveable tractor components.
Hoses must be routed so they are not pinched, bent
sharply, or chafed during operation. Hoses must not
interfere with any tractor control operation or contact
any moving parts.
&
Connect hydraulic hoses to tractor hydraulic couplers
as shown in Figure 9 when loader is attached to trac-
tor.
$
Figure 9. Hydraulic Hose Connection to Tractor
Install Hose Hanger
1. Install hose hanger bracket beneath right side of
the operator’s platform as shown in Figure 10.
Use cap screw, flat washers, and lock nut as
shown in Figure 11.
2. Route hoses through support and secure with
lock pin (15).
11.
12.
13.
14.
15.
58033 Hose hanger bracket
6778 5/16 NC Lock nut
4378 5/16 Flat washer
+26(
+$1*(5
6250 5/16 NC x 1-1/4 HHCS
58047 1/4 x 2-1/2 Lock pin
Figure 10. Hose Hanger Installed
Figure 11. Hose Hanger Assembly
10 Hydraulic Installation
MAN0064 (Rev. 7/20/2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
57923 Hose Kit
Verify Control Movements
1. Mount loader to tractor: Remove mount pins
from loader uprights. Align tractor with loader and
slowly drive tractor into loader. Shut off tractor.
ꢀꢁ
ꢀꢂ
2. Connect loader feedline hoses to the loader
control valve quick couplers. See Figure 19.
3. Comply with all safety rules and start the tractor.
4. Mount loader to tractor by activating bucket
cylinders to raise or lower the loader uprights into
the loader mounts. Slowly drive tractor forward,
activating appropriate cylinders to engage loader
completely into mounts. Insert mounting pins to
secure loader.
●
●
●
Control Handle 1 Forward - Boom down
Control Handle 1 Back - Boom up
5. Check that all tractor hydraulic control lever
positions operate the loader movements correctly.
See Figure 20.
Control Handle 2 Forward - Dump bucket or
attachment
6. If loader movements do not respond correctly,
shut off tractor, relieve pressure, and reconnect
properly. Loader control movements must be
correct before proceeding.
●
Control Handle 2 Back - Roll back bucket or
attachment
Figure 12. Tractor Control Lever Operation
7. Once all loader functions are correct, start the
tractor and operate the loader to check for leaks.
Purge any remaining air from the hydraulic
system and check oil level.
8. When hose routings and correct loader
operations are verified, identify each circuit by
placing a matching colored band around the male
and female quick-disconnect coupler. The
color-coded bands will make reinstallation easier
once the loader has been removed from the
tractor.
9. Attach the plastic tie straps (included in kit) every
20 inches around the hoses to keep them tightly
bundled and away from contact with the ground
or other moving parts on the tractor or loader.
10. Before operating the loader, make sure that the
Pre-Delivery, Delivery, and Pre-Operation Check
Lists from the Loader Operator’s Manual have
been completed.
MAN0064 (Rev. 7/20/2007)
Hydraulic Installation 11
Download from Www.Somanuals.com. All Manuals Search And Download.
1001420 HOSE KIT
General Description
These set-up instructions are for operating the
1020/1027 loader using single-lever control
a
mounted on the right loader upright as shown Figure
13. To use this hydraulic connection, hose kit
1001420 must be connected between loader control
valve and tractor hydraulics.
Install control valve before proceeding.
NOTICE
■
If hydraulic lines are not connected as shown
in this manual, the control valve may be damaged.
A blocked outlet (RETURN) or improper hose con-
nection will cause pressurized oil to enter the
return circuit and damage the valve.
Figure 13. 2-Spool Control Valve Installed (Typical)
Install Adapter Plate
7. Secure with hex head cap screws and flat washer
NOTICE
as shown in Figure 14.
■
Removal of the accessory plate or remote
8. Secure elbows (1) and (2) as shown.
valves with a load being held on the 3-point hitch
will result in escape of high pressure oil and sud-
den, uncontrolled drop of 3-point hitch arms.
13
11
A
15
14
Before attempting to install this kit, the following must
be observed:
1
● Shut off engine, place transmission in neutral,
and apply parking brake.
● Fully lower any equipment supported by the trac-
tor remote hydraulic valves, if so equipped. Acti-
vate any remote valves to relieve all hydraulic
pressure in the remote circuits.
● Fully lower the 3-point hitch.
3
1. Thoroughly clean the top front of the hydraulic
accessory plate.
2
1
2. Install elbows (1) and (2) to adapter plate (3).
Figure 14. Adapter Plate Installed
3. Remove accessory plate cover (A). Be careful not
to disturb the O-rings that need to stay with the
cover plate when it is removed.
A.
----- Accessory plate cover
1. 316004 Elbow, 3/4 JICM x 3/4 ORBM 90°
2. 313032 Elbow, 3/4 JICM x 3/4 JICF 90°
3. 1001421 Adapter plate
4. Install O-rings to bottom of adapter plate (3). Use
petroleum jelly to keep the O-rings in the
counterbores.
11.
13.
14.
4378 5/16 Standard flat washer
21548 5/16 NC x 3-1/4 HHCS
21549 7/16 NC x 3 HHCS
5. Place the adapter plate over hydraulic opening.
6. Place the accessory plate cover onto the adapter
plate. Make sure O-rings stay in the
counterbores.
15. 1001423 7/16 NC x 4-3/4 HHCS
12 Hydraulic Installation
MAN0064 (Rev. 7/20/2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
1001420 Hose Kit
Install Hoses
1. Attach 90° end of hoses (7) to the IN, OUT and
1
PBY ports of the loader control valve.
2. Locate the fill plug on the top of right rear axle
7
and remove.
P
3. Install adapter (5) and elbow (6) into opening.
N
4. Attach hose from the PBY port on the loader
control valve to elbow (2) in the PBY (N) port on
the front of adapter plate (3).
5. Attach hose from the IN port on the loader control
valve to elbow (1) in the PRESSURE (P) port on
the side of adapter plate.
2
7
6. Attach hose from the OUT port on the loader
control valve to elbow (6) in the RETURN port on
the top of the rear axle.
Figure 15. Hose Connection at Adapter Plate
7
1. 316004 Elbow, 3/4 JICM x 3/4 ORBM 90°
2. 313032 Elbow, 3/4 JICM x 3/4 JICF 90°
5. 1001419 Adapter, 7/8 O-ring F x 1-3/8 Trd M
or
6
5. 1001657 Adapter, 7/8 O-ring F x 1-5/8 Trd M
6.
60 Elbow, 3/4 JICM x 7/8 ORBM 90°
7. 1001422 Hose, 86" x 3/4 JICF x 3/4 JICF
5
Figure 16. RETURN Port Connection
MAN0064 (Rev. 7/20/2007)
Hydraulic Installation 13
Download from Www.Somanuals.com. All Manuals Search And Download.
1001420 Hose Kit
Install Hose Hanger
1. Install hose hanger bracket (8) under platform
between brake pedals and chassis as shown in
Figure 17.
2. Secure with hex head cap screw (10), flat
washers (11), and lock nut (12).
3. Route hoses through hose hanger bracket and up
behind right platform as shown in Figure 18.
4. Secure hoses in hose hanger with lock pin (9).
5. Secure hoses every 20 inches with plastic ties.
8.
9.
58033 Hose hanger bracket
58047 1/4 x 2-1/2 Lock pin
6250 5/16 NC x 1-1/4 HHCS
4378 5/16 Standard flat washer
6778 5/16 NC Lock nut
10.
11.
12.
Figure 17. Hose Hanger Installed
Figure 18. Hose Routing
Connect Loader Feedline Hoses
1. The control valve kit contains hoses assembled
with quick couplers. Attach the hoses to loader
feedlines, following the color pattern.
2. Connect loader supply hoses to control valve
hydraulic couplers when attaching loader.
Figure 19. Control Valve and 1020/1027 Loader Feedline Connections
14 Hydraulic Installation
MAN0064 (Rev. 7/20/2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
1001420 Hose Kit
Verify Control Movements
1. Mount loader to tractor: Remove mount pins
from loader uprights. Align tractor with loader and
slowly drive tractor into loader. Shut off tractor.
2. Connect loader feedline hoses to the loader
control valve quick couplers. See Figure 19.
3. Comply with all safety rules and start the tractor.
4. Mount loader to tractor by activating bucket
cylinders to raise or lower the loader uprights into
the loader mounts. Slowly drive tractor forward,
activating appropriate cylinders to engage loader
completely into mounts. Insert mounting pins to
secure loader.
●
●
●
●
Handle forward - Boom down
Handle forward to limit - Float position
Handle back - Boom up
5. Check that all tractor hydraulic control lever
positions operate the loader movements correctly.
See Figure 20.
Handle right -
6. If loader movements do not respond correctly,
shut off tractor, relieve pressure, and reconnect
properly. Loader control movements must be
correct before proceeding.
Dump bucket or attachment (slow)
●
●
Handle right to limit -
Dump bucket or attachment (fast)
Handle to left - Rollback bucket or attachment
7. Once all loader functions are correct, start the
tractor and operate the loader to check for leaks.
Purge any remaining air from the hydraulic
system and check oil level.
Figure 20. Single Lever Control Operation
8. When hose routings and correct loader
operations are verified, identify each circuit by
placing a matching colored band around the male
and female quick-disconnect coupler. The
color-coded bands will make reinstallation easier
once the loader has been removed from the
tractor.
9. Attach the plastic tie straps (included in kit) every
20 inches around the hoses to keep them tightly
bundled and away from contact with the ground
or other moving parts on the tractor or loader.
10. Before operating the loader, make sure that the
Pre-Delivery, Delivery, and Pre-Operation Check
Lists from the Loader Operator’s Manual have
been completed.
MAN0064 (Rev. 7/20/2007)
Hydraulic Installation 15
Download from Www.Somanuals.com. All Manuals Search And Download.
1023582 HOSE KIT
General Description
These set up instructions are for operating the LU126
loader using a single lever control valve mounted to
the right loader mount bracket as shown in Figure 21.
To use this hydraulic connection, hose kit 1023582
must be connected between loader control valve and
tractor hydraulics.
Install loader control valve before proceeding.
NOTICE
■
If hydraulic lines are not connected as shown
in this manual, the control valve may be damaged.
A blocked outlet (RETURN) or improper hose con-
nection will cause pressurized oil to enter the
return circuit and damage the valve.
DP8
Figure 21. Control Valve Installed
Install Adapter Plate
6. Place the accessory plate cover onto the adapter
plate. Make sure O-rings stay in the counter-
bores.
NOTICE
■
Removal of the accessory plate or remote
valves with a load being held on the 3-point hitch
will result in escape of high pressure oil and sud-
den, uncontrolled drop of 3-point hitch arms.
7. Secure with hex head cap screws and flat washer
as shown in Figure 22.
Before attempting to install this kit, the following must
be observed:
● Shut off engine, place transmission in neutral,
and apply parking brake.
● Fully lower any equipment supported by the trac-
tor remote hydraulic valves, if so equipped. Acti-
vate any remote valves to relieve all hydraulic
pressure in the remote circuits.
● Fully lower the 3-point hitch.
1. Thoroughly clean the top front of the hydraulic
accessory plate.
Figure 22. Adapter Plate Installed
2. Install elbow (12) and adapter (21) to adapter
A.
----- Accessory plate cover
plate (2).
2. 1001421 Adapter plate
10. 1001423 7/16 NC X 4-3/4 HHCS
12. 316004 Elbow, 3/4 JICM x 3/4 ORBM 90°
3. Remove accessory plate cover (A). Be careful not
to disturb the O-rings that need to stay with the
cover plate when it is removed.
15.
16.
19.
21.
21549 7/16 NC x 3 HHCS
4. Install O-rings to bottom of adapter plate (2). Use
petroleum jelly to keep the O-rings in the
counterbores.
21548 5/16 NC x 3-1/4 HHCS
4378 5/16 Standard flat washer
61 Adapter, 3/4 JICM x 3/4 ORBM
5. Place the adapter plate over hydraulic opening.
16 Hydraulic Installation
MAN0064 (Rev. 7/20/2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
1023582 Hose Kit
Install Hoses
1. Attach straight end of hoses (1) to the IN, OUT
and PBY ports of the loader control valve.
2. Locate the fill plug on the top of right rear axle
and remove.
3. Install adapter (3) and adapter (11) into opening.
4. Attach hose from the PBY port on the loader
control valve to elbow (12) in the PBY (N) port on
the front of adapter plate (2).
5. Attach hose from the IN port on the loader control
valve to adapter (21) in the PRESSURE (P) port
on the side of adapter plate.
6. Attach hose from the OUT port on the loader
control valve to adapter (11) in the RETURN port
on the top of the rear axle.
1. 1001422 Hose, 86" x 3/4 JICF x 3/4 JICF
2. 1001421 Adapter plate
3. 1001419 Adapter, 7/8 O-ring F x 1-3/8 Trd M
3. 1001657 Adapter, 7/8 O-ring F x 1-5/8 Trd M
11. 316016 Adapter, 3/4 JICM x 7/8 ORBM
12. 316004 Elbow, 3/4 JICM x 3/4 ORBM 90°
Figure 23. Hydraulic Fitting Installation
21.
61 Adapter, 3/4 JICM x 7/8 ORBM 90°
Install Hose Hanger
1. Install hose hanger bracket (14) under platform
between brake pedals and chassis as shown in
Figure 24.
2. Secure with hex head cap screw (18), flat
washers (19), and lock nut (17).
3. Route hoses through hose hanger bracket and up
behind right platform as shown in Figure 18.
4. Secure hoses in hose hanger with lock pin (13).
5. Secure hoses every 20 inches with plastic ties.
Figure 24. Hose Hanger Installed
14.
13.
17.
18.
19.
58033 Hose hanger bracket
58047 1/4 x 2-1/2 Lock pin
6778 5/16 NC Lock nut
6250 5/16 NC x 1-1/4 HHCS
4378 5/16 Standard flat washer
Figure 25. Hose Routing
MAN0064 (Rev. 7/20/2007)
Hydraulic Installation 17
Download from Www.Somanuals.com. All Manuals Search And Download.
1023582 Hose Kit
Connect Loader Feedline Hoses
1. The control valve kit contains hoses assembled
with quick couplers. Attach the hoses to loader
feedlines, following the color pattern.
2. Connect loader supply hoses to control valve
hydraulic couplers when attaching loader.
Figure 26. Control Valve & LU126 Loader Feedline Connections
Verify Control Movements
1. Mount loader to tractor: Remove mount pins
from loader uprights. Align tractor with loader and
slowly drive tractor into loader. Shut off tractor.
9. Attach the plastic tie straps (included in kit) every
20 inches around the hoses to keep them tightly
bundled and away from contact with the ground
or other moving parts on the tractor or loader.
2. Connect loader feedline hoses to the loader
10. Before operating the loader, make sure that the
Pre-Delivery, Delivery, and Pre-Operation Check
Lists from the Loader Operator’s Manual have
been completed.
control valve quick couplers. See Figure 26.
3. Comply with all safety rules and start the tractor.
4. Mount loader to tractor by activating bucket
cylinders to raise or lower the loader uprights into
the loader mounts. Slowly drive tractor forward,
activating appropriate cylinders to engage loader
completely into mounts. Insert mounting pins to
secure loader.
5. Check that all tractor hydraulic control lever
positions operate the loader movements correctly.
See Figure 27.
6. If loader movements do not respond correctly,
shut off tractor, relieve pressure, and reconnect
properly. Loader control movements must be
correct before proceeding.
●
●
●
●
Handle forward - Boom down
Handle forward to limit - Float position
Handle back - Boom up
7. Once all loader functions are correct, start the
tractor and operate the loader to check for leaks.
Purge any remaining air from the hydraulic
system and check oil level.
Handle right -
Dump bucket or attachment (slow)
8. When hose routings and correct loader
operations are verified, identify each circuit by
placing a matching colored band around the male
and female quick-disconnect coupler. The
color-coded bands will make reinstallation easier
once the loader has been removed.
●
●
Handle right to limit -
Dump bucket or attachment (fast)
Handle to left - Rollback bucket or attachment
Figure 27. Single Lever Control Operation
18 Hydraulic Installation
MAN0064 (Rev. 7/20/2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
1023596 HOSE KIT
General Description
Install Hose Fittings
These instructions are for operating the LU126 loader
using the tractor hydraulic remote control lever. To
use this hydraulic connection, the tractor must be
equipped with four tractor hydraulic couplers.
1. Attach elbow (2) and male quick coupler (3) to
each loader supply hose (1).
2. Connect loader supply hoses to loader steel
feedlines. Following pattern shown in Figure 8.
NOTE: Male quick couplers (3) for connection to trac-
tor are NOT included with the hose kit but are avail-
able as service parts.
1. 1023472 Hose, 170" x 3/4 JICM x 3/4 JICM
2. 313053 Elbow, 3/4 JICF x 1/2 NPTM
3.
66511 Quick coupler, male 1/2
Figure 28. LU126 Loader Supply Hose Connection
Route Hydraulic Hoses
Route hoses along loader mount, under the right side
of the operator’s platform, and over the rear axle.
Be sure to avoid contact with 3-point linkage, brake
pedals, and other moveable tractor components.
Hoses must be routed so they are not pinched, bent
sharply, or chafed during operation. Hoses must not
interfere with any tractor control operation or contact
any moving parts.
Connect hydraulic hoses to tractor hydraulic couplers.
+26(
+$1*(5
Install Hose Hanger
1. Install hose hanger bracket beneath right side of
the operator’s platform as shown in Figure 29.
Use cap screw, flat washers, and lock nut as
shown in Figure 29.
Figure 29. Hose Hanger Installed
4.
12.
15.
16.
17.
58033 Hose hanger bracket
58047 1/4 x 2-1/2 Lock pin
6778 5/16 NC Lock nut
2. Route hoses through support and secure with
lock pin (12).
6250 5/16 NC x 1-1/4 HHCS
4378 5/16 Standard flat washer
MAN0064 (Rev. 7/20/2007)
Hydraulic Installation 19
Download from Www.Somanuals.com. All Manuals Search And Download.
1023596 Hose Kit
Verify Control Movements
1. Mount loader to tractor: Remove mount pins
from loader uprights. Align tractor with loader and
slowly drive tractor into loader. Shut off tractor.
ꢀꢁ
ꢀꢂ
2. Connect loader feedline hoses to the loader
control valve quick couplers. See Figure 19.
3. Comply with all safety rules and start the tractor.
4. Mount loader to tractor by activating bucket
cylinders to raise or lower the loader uprights into
the loader mounts. Slowly drive tractor forward,
activating appropriate cylinders to engage loader
completely into mounts. Insert mounting pins to
secure loader.
●
●
●
Control Handle 1 Forward - Boom down
Control Handle 1 Back - Boom up
5. Check that all tractor hydraulic control lever
positions operate the loader movements correctly.
See Figure 20.
Control Handle 2 Forward - Dump bucket or
attachment
6. If loader movements do not respond correctly,
shut off tractor, relieve pressure, and reconnect
properly. Loader control movements must be
correct before proceeding.
●
Control Handle 2 Back - Roll back bucket or
attachment
Figure 30. Tractor Control Lever Operation
7. Once all loader functions are correct, start the
tractor and operate the loader to check for leaks.
Purge any remaining air from the hydraulic
system and check oil level.
8. When hose routings and correct loader
operations are verified, identify each circuit by
placing a matching colored band around the male
and female quick-disconnect coupler. The
color-coded bands will make reinstallation easier
once the loader has been removed from the
tractor.
9. Attach the plastic tie straps (included in kit) every
20 inches around the hoses to keep them tightly
bundled and away from contact with the ground
or other moving parts on the tractor or loader.
10. Before operating the loader, make sure that the
Pre-Delivery, Delivery, and Pre-Operation Check
Lists from the Loader Operator’s Manual have
been completed.
20 Hydraulic Installation
MAN0064 (Rev. 7/20/2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
111877 LOADER MOUNTING KIT
REF PART
QTY
DESCRIPTION
Right rear mount
REF PART
QTY
DESCRIPTION
1
2
1026490
1026491
1001642
1026492
1026493
1
1
1
1
1
15
16
17
20
57817 14 5/8 Hardened flat washer
Left rear mount
Front mount
Right side rail
Left side rail
735 *
902 *
8
2
1
3/4 NC x 2 HHCS
5/8 NC x 2 HHCS
3
4
57913
Grill guard kit - optional
(includes items 21 through 25)
5
21
22
23
24
25
57822
1093 *
3379 *
57816
855 *
1
4
4
4
4
Grill guard
10
12
13
14
230 * 12 5/8 NC Plated Hex nut
300517 * 3/4 NC x 1-3/4 HHCS GR5
301130 * 12 5/8 NC x 1-1/2 Carriage bolt GR5
57798 3/4 Hardened flat washer
1/2 NC Plated hex nut
1/2 NC x 1-1/2 HHCS GR5
1/2 Hardened flat washer
1/2 Lock washer
4
8
HHCS Hex Head Cap Screw
* Standard hardware, obtain locally
(Rev. 05/18/2010)
MAN0064 (Rev. 7/20/2007)
Parts 21
Download from Www.Somanuals.com. All Manuals Search And Download.
1001420 HOSE KIT
(1020/1027 LOADERS)
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
A
1
2
3
5
———
1
2
1
1
1
Accessory plate (tractor part)
Elbow, 3/4 JICM x 3/4 ORBM 90°
Elbow, 3/4 JICM x 3/4 JICF 90°
Ford PBY Plate adapter
10
11
12
13
14
6250 *
1
3
1
1
2
2
4
5/16 NC x 1-1/4 HHCS GR5
5/16 Standard flat washer
5/16 NC Lock nut
316004
313032
1001421
1001419
- or -
4378 *
6778 *
21548 *
21549 *
5/16 NC x 3-1/4 HHCS GR8
7/16 NC x 3 HHCS GR8 ZP
7/16 NC x 4-3/4 HHCS GR8
Plastic tie (not shown)
Adapter, 7/8 O-ring F x 1-3/8 Trd M
15 1001423 *
16 88 *
5
6
7
8
9
1001657
60
1
1
3
1
1
Adapter, 7/8 O-ring F x 1-5/8 Trd M
Elbow, 3/4 JICM x 7/8 ORBM
Hose, 86" x 3/4 JICF x 3/4 JICF
Hose hanger bracket
HHCS Hex Head Cap Screw
1001422
58033
* Standard hardware, obtain locally
58047
Pin lock 1/4 x 2-1/2
22 Parts
MAN0064 (Rev. 7/20/2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
1023582 HOSE KIT
(LU126 LOADER)
REF PART
QTY
DESCRIPTION
A
1
2
3
———
1001422
1001421
1001419
- or -
1
3
1
1
Accessory plate (tractor part)
Hose, 86" x 3/4 JICF x 3/4 JICF
Ford PBY Plate adapter
Adapter, 7/8 O-ring F x 1-3/8 Trd M
3
1001657
1
2
1
1
1
1
2
1
1
1
3
4
1
Adapter, 7/8 O-ring F x 1-5/8 Trd M
7/16 NC x 4-3/4 HHCS GR8
Adapter, 3/4 JICM x 7/8 ORBM
Elbow, 3/4 JICM x 3/4 ORBM 90°
Pin lock 1/4 x 2-1/2
10 1001423 *
11
12
13
14
15
16
17
18
19
20
21
316016
316004
58047
58033
21549 *
21548 *
6778 *
6250 *
4378 *
88 *
Hose hanger bracket
7/16 NC x 3 HHCS GR8 ZP
5/16 NC x 3-1/4 HHCS GR8
5/16 NC Lock nut
5/16 NC x 1-1/4 HHCS GR5
5/16 Standard flat washer
Plastic tie (not shown)
61
Adapter, 3/4 JICM x 3/4 ORBM
HHCS Hex Head Cap Screw
* Standard hardware, obtain locally
MAN0064 (Rev. 7/20/2007)
Parts 23
Download from Www.Somanuals.com. All Manuals Search And Download.
57923 HOSE KIT
(10120/1027 LOADERS)
REF PART
QTY
DESCRIPTION
1
2
3
57912
313053
66511
4
4
4
Hose, 120" x 3/4 JICM x 3/4 JICM
Elbow, 3/4 JICF x 1/2 NPTM 90°
Quick coupler, male 1/2
(not included in kit)
11
12
13
14
15
16
58033
6778 *
4378 *
6250 *
58047 *
88 *
1
1
2
1
1
Hose hanger bracket
5/16 NC Lock nut
5/16 Flat washer
5/16 NC x 1-1/4 HHCS GR5
1/4 x 2-1/2 Lock pin
Plastic tie straps (not shown)
HHCS Hex Head Cap Screw
* Standard hardware, obtain locally
1023596 HOSE KIT
(LU126 LOADER)
REF PART
QTY
DESCRIPTION
1
2
3
1023472
4
4
4
Hose, 170" x 3/4 JICM x 3/4 JICM
Elbow, 3/4 JICF x 1/2 NPTM 90°
313053
66511
Quick coupler, male 1/2
(not included in kit)
4
58033
58047 *
6778 *
6250 *
4378 *
88 *
1
1
1
1
2
Hose hanger bracket
1/4 x 2-1/2 Lock pin
12
15
16
17
18
5/16 NC Lock nut
5/16 NC x 1-1/4 HHCS GR5
5/16 Flat washer
Plastic tie straps (not shown)
HHCS Hex Head Cap Screw
* Standard hardware, obtain locally
24 Parts
MAN0064 (Rev. 7/20/2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
SAE 2
SAE 5
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
8
lbs-ft
10
N-m
13
lbs-ft
14
N-m
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
7/16"
1/2"
6
18
37
12
17
19
26
27
9/16"
5/8"
23
31
35
47
49
67
36
48
55
75
78
106
163
232
325
569
907
1383
3/4"
55
75
85
115
164
230
403
642
979
120
171
240
420
669
1020
13/16"
15/16"
1-1/8"
1-5/16"
1-1/2"
78
106
149
261
416
634
121
170
297
474
722
110
192
306
467
METRIC SERIES
TORQUE
CHART
8.8
Metric Bolt Head
Identification
10.9
A
Metric
Grade 8.8
Metric
Grade 10.9
COARSE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
FINE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
A
A
Diameter &
Thread Pitch Wrench
(Millimeters)
Diameter &
Thread Pitch
(Millimeters)
Size
N-m
lbs-ft
6
N-m
lbs-ft
6
6 x 1.0
10 mm
13 mm
16 mm
18 mm
21 mm
24 mm
27 mm
30 mm
34 mm
36 mm
46 mm
8
11
27
8
8
11
29
8
6 x 1.0
8 x 1.0
8 x 1.25
10 x 1.5
12 x 1.75
14 x 2.0
16 x 2.0
18 x 2.5
20 x 2.5
22 x 2.5
24 x 3.0
30 x 3.0
20
15
20
21
16
22
39
29
54
40
41
30
57
42
10 x 1.25
12 x 1.25
14 x 1.5
16 x 1.5
18 x 1.5
20 x 1.5
22 x 1.5
24 x 2.0
30 x 2.0
68
50
94
70
75
55
103
163
250
363
507
684
861
1740
76
109
169
234
330
451
571
1175
80
151
234
323
457
623
790
1626
111
173
239
337
460
583
1199
118
181
263
367
495
623
1258
87
120
184
268
374
505
635
1283
125
172
244
332
421
867
133
194
270
365
459
928
Typical Washer
Installations
Bolt
Flat Washer
Lock Washer
8/9/00
Bolt Torque & Size Charts (Rev. 3/28/2007)
Appendix 25
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
5/8
3/4
7/8
IN
1
2
7
3
4
5
6
MM
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM 10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG .............................................................. Agriculture
MPa ........................................................ Mega Pascal
N ......................................................................Newton
NC...................................................... National Coarse
NF...........................................................National Fine
NPSM .................... National Pipe Straight Mechanical
NPT...........................................National Pipe Tapered
NPT SWF......... National Pipe Tapered Swivel Female
ORBM...........................................O-Ring Boss - Male
P .......................................................................... Pitch
PBY.......................................................Power-Beyond
psi ......................................... Pounds per Square Inch
PTO......................................................Power Take Off
QD ................................................... Quick Disconnect
RH.............................................................. Right Hand
ROPS........................... Roll-Over Protective Structure
RPM........................................Revolutions Per Minute
RT ........................................................................Right
SAE.......................... Society of Automotive Engineers
UNC..................................................... Unified Coarse
UNF ..........................................................Unified Fine
UNS ..................................................... Unified Special
ASABE ....................American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE....... American Society of Agricultural Engineers
ATF................................Automatic Transmission Fluid
BSPP............................. British Standard Pipe Parallel
BSPTM................ British Standard Pipe Tapered Male
CV ....................................................Constant Velocity
CCW.............................................. Counter-Clockwise
CW .............................................................. Clockwise
F.......................................................................Female
FT.............................................................. Full Thread
GA .....................................................................Gauge
GR (5, etc.)........................................... Grade (5, etc.)
HHCS ........................................Hex Head Cap Screw
HT ...........................................................Heat-Treated
JIC.................Joint Industry Council 37° Degree Flare
LH................................................................. Left Hand
LT ...........................................................................Left
m ........................................................................ Meter
mm ............................................................... Millimeter
M ..........................................................................Male
Bolt Torque & Size Charts (Rev. 3/28/2007)
26 Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
All Models Except Mow’n MachineTM Zero-Turn Mowers
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
Model Number: ____________________________
From (Dealer): __________________________________________
Serial Number: __________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth
below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Duration (from date of
delivery to the original
purchaser)
Model Number
Gearbox
Seals
All units listed below
2 years
BW1260, BW1620, BW1800, BW2400
8 years
7 years
BW240HD, BW180HD, BW180HB, BW126HB
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X,
DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240
6 years
Gearbox
components PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2, RM660-2, RM990-
3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2,
5 years
9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD, BW180LH, TC/R74, TC/R68, TC/R60
3 years (1 year if used in rental or
commercial applications)
RDC54, RD60, RD72, TBW150C, TS/R60, TS/R52, TS/R44
Blade
RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2, 9204RD-2
spindles
3 years
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW126HB, BW180-3, BW180HB,
Rust-through BW180HD, BW1260, BW1800, BW240, BW240HD, 2162, 3240, DS1260, DSO1260, DS1440, 10 years
TS1680
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially
modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center.
This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made with parts other
than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to a
third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS, in
its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of
purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY.
THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues
or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or
rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, its
authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty. Answers to any
questions regarding warranty service and locations may be obtained by contacting:
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
F-3079 (Rev. 3/31/2010)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(Replacement Parts For All Models Except Mow’n Machine
Zero-Turn Mowers and Woods Boundary Utility Vehicles)
TM
TM
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-8494 (Rev. 6/23/2005)
Download from Www.Somanuals.com. All Manuals Search And Download.
|