Wells-Gardner Electronics Corporation
Service Manual for
D9300 Series
Digital-Control Color Monitor
Wells-Gardner Electronics
5500W. 55th Street Suite A
Mc,Cook Illinois 60525-3605
(708) 290-2100
069X3045-100
ECN: E01024
Date: 8-18-00
Printed on 03/20/03
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
SAFETY PRECAUTION:
1.
WARNING: Service should not be attempted by anyone unfamiliar with the necessary
precautions on this unit. The following precautions are necessary during servicing.
1-1
1-2
Some parts, such as a picture tube in this unit, have special safety-related characteristics
for X-RAY RADIATION protection.
For continued safety, the parts replacement should be undertaken referring to below
article (1-2 and 1-5).
Many electrical mechanical parts in this unit have special safety-related characteristics for
protection against shock hazard and others. These characteristics are often passed
unnoticed by visual inspection and the protection afforded by them cannot necessarily be
obtained by using replacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special characteristics are identified in the manual
and supplements by shading on the schematic diagram and the parts list. Before replacing
any of these components, read the parts list in this manual carefully.
1-3
1-4
1-5
When replacing the chassis in the cabinet, always be certain that all the protective devices
are installed properly, such as insulating covers, strain relief, etc.
Before replacing the back cover of the set, thoroughly inspect the inside of the cabinet to
see that no stray parts or tools have been left inside.
Before returning the set to the customer, always perform an AC leakage current check on
the exposed metallic parts of the cabinet, such as terminal, screwheads, metal overlays,
control shafts, etc. To insure the set is safe to operate without danger of electrical shock,
plug the AC line cord directly into a 120V AC outlet (do not use a line isolation
transformer during this check). Use an AC voltmeter having 5000 ohms per volt or more
sensitivity in the following manner. Connect a 1500 ohm, 10 watt resistor, parallel with a
(0.15uF) capacitor. Reverse the AC plug in the AC outlet and repeat the AC voltage
measurements for each exposed metallic part. Voltage measured must not exceed 0.3V
RMS. This corresponds to 0.2mA AC, any value exceeding this limit constitutes a potential
shock hazard and must be corrected immediately.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
2.
SPECIFICATION:
2-1 Picture Tube.
xꢀ Size: 18V
xꢀ Dot Pitch: .25mm
2-2 Signal Input.
xꢀ Video Input: Analog, Positive Signal (0.7V p-p)
xꢀ Horizontal Sync: TTL Level, Positive or Negative Pulse
xꢀ Scanning : 28 KHz-70KHz
xꢀ Vertical Input: TTL Level, Positive or Negative pulse
xꢀ Scanning : 40-160Hz
2-3 Power Supply.
xꢀ Power Input : 120-240 VAC, 50/60Hz
xꢀ Fuse Rating: 250V, 3.15A
xꢀ Power Consumption
Normal : less than 130W
2-4 OSD (On Screen Display) Control:
Refer to page 7
2-5 Operating Temperature: 0qC - 55qC
2-6 Operating Humidity: 10% - 90% (Noncondensing)
2-7 Net Weight : 17kg (37lbs)
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
3.
TECHNICAL FEATURES:
3-1
Microprocessor control with OSD (On screen display menu).
Microprocessor recognizes the input computer signal and signal output from the customer
control board connected to the main board by a flat cable.
3-2
Universal AC Input Voltage.
Power supply operates on 120-240 VAC at 60/50Hz for use all over the world.
3-3. Protection Circuit for over-current.
When an over-current condition occurs in the circuit, the protection circuit operates in
order to prevent the components from electrical shock or other risks.
3-4
3-5
Override function.
A (NO SIGNAL MESSAGE) is displayed on the screen if no signal is present at the signal
input cable while the monitor is powered on.
Control panel.
If you require different display characteristics other than the factory mode presets of size,
position, color settings, use the control panel to program it to your requirements in each
resolution mode. These adjusted settings are kept in memory even if you change resolution
mode or turn off the monitor.
3-6
I²C BUS control.
The monitor is designed with I²C BUS control for simplifying the circuitry.
The number of total components is less than 610 pcs.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
4.
TIMING CHART:
Factory Pre-Set Timing Modes.
Horizontal and Vertical Timing Diagram for Table 1
.
TABLE 1 :
QUANTUM 801GX
MVP-NSW
US500
MK6
VGA_M4
FORMAT
MODE 1
640*400
29.63Hz
33.75µs
1.76µs
MODE 2
640*400
31.5KHz
31.778µs
3.88µs
MODE 3
640*480
31.35KHz
28.251µs
3.86µs
MODE 4
8514/A 1024*768
35.552KHz
28.251µs
3.920µs
DESCRIPTION
FH
A
B
H
C
D
1.84µs
1.247µs
3.52µs
26.67µs
1.86µs
2.04µs
25.5µs
25.4µs
22.806µs
0.170µs
E
0.63µs
0.58µs
POL.
FV
A
POSITIVE
62.91Hz
15.88ms
0.0338ms
1.680ms
13.56ms
0.675ms
POSITIVE
ANALOG
POSITIVE
70.1Hz
POSITIVE
59.8Hz
POSITIVE
86.960Hz
11.500ms
0.113ms
14.2ms
16.72ms
0.066ms
1.052ms
15.36ms
0.316ms
POSITIVE
ANALOG
B
0.0636ms
1.110ms
12.7ms
V
C
0.563ms
D
10.810ms
0.014ms
E
0.408ms
POSITIVE
ANALOG
POL.
VIDEO
POSITIVE
ANALOG
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
QUANTUM 801GX
FORMAT
VG900602
DMT8075
VS900603
VG901101
MODE 8
VG901101
MODE 9
MODE 5, S-VGA
VESA 680*480
37.500KHz
26.667us
MODE 6
VGA 800*600
37.879KHz
26.400µs
3.200µs
MODE 7 VGA
VESA 800*600
46.875KHz
21.333µs
1.616µs
DESCRIPTION
VESA 800*600 VESA 1024*768
FH
A
B
48.077KHz
20.800µs
2.400µs
48.363KHz
20.677µs
2.231µs
2.032us
H
V
C
D
E
POL.
FV
A
B
C
D
E
3.810us
20.317us
0.508us
NEGETIVE
75.00Hz
13.333ms
0.080ms
.427ms
12.800ms
0.027ms
2.200µs
20.000µs
1.000µs
POSITIVE
60.317Hz
16.579ms
0.106ms
0.607ms
15.840ms
0.026ms
POSITIVE
ANALOG
3.232µs
16.162µs
0.323µs
POSITIVE
75.000Hz
13.333ms
0.064ms
0.448ms
12.800ms
0.021ms
POSITIVE
ANALOG
1.280µs
16.000µs
1.119µs
1.615µs
15.754µs
0.998µs
POSIIVE
72.188Hz
13.853ms
0.125ms
0.478ms
12.480ms
0.722ms
POSITIVE
ANALOG
NEGATIVE
60.004Hz
16.666ms
0.124ms
0.600ms
15.880ms
0.062ms
NEGATIVE
ANALOG
POL.
VIDEO
NEGETIVE
ANALOG
QUANTUM 801GX
FORMAT
DMT8085
MODE 10
VS910801
MODE 11
DMT1075
MODE 12
DMT1260
MODE 13
DMT1085
MODE 14
DESCRIPTION
VESA 800*600 VESA 1024*768 VESA 1024*768 VESA 1280*1024 VESA 1024*768
FH
A
B
53.674KHz
18.631µs
1.138µs
56.476KHz
17.707µs
1.813µs
60.023KHz
16.660µs
1.219µs
63.981KHz
15.698µs
1.037µs
68.677KHz
14.561µs
1.016µs
H
V
C
D
E
POL.
FV
A
B
C
D
E
2.702µs
14.222µs
0.569µs
1.920µs
13.653µs
0.321µs
2.235µs
13.003µs
0.203µs
2.296µs
11.852µs
0.360µs
2.201µs
10.836µs
0.508µs
POSITIVE
85.062Hz
11.756ms
0.056ms
0.503ms
11.179ms
0.019ms
POSITIVE
ANALOG
NEGATIVE
70.069Hz
14.272ms
0.106ms
0.513ms
13.599ms
0.054ms
NEGATIVE
ANALOG
POSITIVE
75.029Hz
13.328ms
0.050ms
0.466ms
12.795ms
0.017ms
POSITIVE
ANALOG
POSITIVE
60.020Hz
16.638ms
0.047ms
0.594ms
16.005ms
0.016ms
POSITIVE
ANALOG
POSITIVE
84.997Hz
11.765ms
0.044ms
0.524ms
11.183ms
0.015ms
POSITIVE
ANALOG
POL.
VIDEO
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
5.
SET UP:
Setting up your monitor is easy. All you have to do is make a few simple connections and
adjustments. The procedure is as follows:
5.1
Start Up.
Your monitor starts up automatically when you insert the power plug to power source.
5-2. Single Cable Connection.
Connect the 15pin signal cable to the source and lock both screws to ensure that the
monitor is properly grounded.
D type 15pin connector:
PIN NO.
DESCRIPTION
VIDEO RED
VIDEO GREEN
VIDEO BLUE
PIN NO.
DESCRIPTION
N.C.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
GROUND
N.C.
N.C.
N.C.
SDA
HOR-SYNC
VER-SYNC
SCL
VIDEO RED GROUND
VIDEO GREEN GROUND
VIDEO BLUE GROUND
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
6.
CONTROLS AND ADJUSTMENTS:
There are four switches on the control panel. Adjustable controls allow the best display
status for individual requirements.
6-1. Key Function.
1. MODE/EXIT
MODE – Call the Main-Menu OSD
2. SEL / Degauss
SEL – Call the Sub-Menu OSD
Degauss – Degausses the CRT (active when the OSD is not displayed)
3. DOWN/UP
When the Main-Menu is displayed, you can select each function using these keys.
When the Sub-Menu is displayed, you can change the amplitude of
the selected function of the screen using these keys.
6-2. O.S.D. CONTROL METHOD.
User Adjustment.
Location
Adjustment Method
Function
Brightness
Contrast
Horizontal Position
Horizontal Size
Vertical Position
Vertical Size
Side Pincushion
Trapezoid
CUSTOMER
CONTROL
PCB
OSD CONTROL
Pin Balance
Parallelogram
VR control, VR501
VR301
Sub-Bright
MAIN PCB
H.V. Adjustment*
Focus and Screen
Tilt
FBT
VR302
*NOTE: (FACTORY ADJUSTED AND EPOXYED VR301)
(HOT MELTED SCREEN FBT)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
6-3. OSD Controls
- User’s control.
A. BRIGHTNESS ADJUSTMENT.
1) Press the “MODE” key then Main-Menu OSD comes out as figure on next page.
2) Search “BRIGHTNESS” sub-menu using “UP/DOWN” key on the Main-Menu OSD.
3) Select the “BRIGHTNESS” by pressing “SEL” key. The “BRIGHTNESS” OSD color
changes from yellow to red.
4) Adjust Brightness as much as you want using “UP/DOWN” key.
5) After finishing the Brightness adjust, press the “MODE” key. The “BRIGHTNESS” OSD
color changes from red to yellow and the changed Brightness value saves automatically.
6) If you want to adjust other functions (sub-menu), search the function using “UP/DOWN”
keys, and then repeat the same procedures of steps 3-5.
7) Press the “MODE” key again to finish adjustments and the OSD will disappear.
If no action is taken in the OSD, the menu will disappear by itself.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
A. BRIGHTNESS ADJUSTMENT
B.
C.
D.
E.
F.
G.
H.
I.
CONTRAST
H. POSITION
H. SIZE
V. POSITION
V. SIZE
PINCUSHION
TRAPEZOID
PARRALLELOG ADJUST
PIN BALANCE ADJUST
ADJUST
ADJUST
ADJUST
ADJUST
ADJUST
ADJUST
ADJUST
SAME ABOVE
SAME ABOVE
SAME ABOVE
SAME ABOVE
SAME ABOVE
SAME ABOVE
SAME ABOVE
SAME ABOVE
SAME ABOVE
J.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
6-3 OSD Controls (continued):
K. COLOR ADJUSTMENT
1) Press the “MODE” to show the Main-Menu OSD as shown by the left-below figure.
2) Search the “COLOR” sub-menu using “UP/DOWN” key on the Main-Menu OSD.
3) SELECT the “COLOR” by pressing “SEL” key. The color Sub-Menu OSD appears as
shown by the right-below figure.
4) Search “USER” using “UP/DOWN” key. (“COLOR1” and “COLOR2” are adjusted in
factory by auto-alignment machine.)
5) Press “SELECT” key to adjust “RED”, “GREEN” and “BLUE”. Each is selected by
pressing the “SELECT” key. The selected item changes OSD color from white to shown
it’s own color as the character. (ex. “RED” goes red in color).
6) Adjust “RED”, “GREEN” or “BLUE” using “UP/DOWN” key.
7) Press “MODE” key to finish the color adjustment. The OSD will then go back to the
Main-Menu.
8) Press the “MODE” key again to finish adjustments and make the OSD disappear.
COLOR ADJUST
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
L.
RECALL.
When the “RECALL” key is pressed, all user’s adjustment values are changed to the factory
values.
M.
LANGUAGE.
The menu is available in four languages.
1. Press the “MODE” key and the Main-Menu OSD will appear as in the previous figure.
2. Search the “LANGUAGE” sub-menu using the “UP/DOWN” key on the Main-Menu OSD.
3. Select the “LANGUAGE” by pressing the “SEL” key. Then the Language sub-menu will
appear as in the following figure
4. Search any language using the “UP/DOWN” key.
5. Select a language by pressing the “SEL” key.
6. Press “MODE” key to finish and save the selected language.
Then the OSD will return to Main-Menu in the selected language.
Press the “MODE” key again to finish the adjustment then the OSD will disappear.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
7.
ADJUSTMENT SPECIFICATION:
7-1. Adjustment Sequence:
The monitor requires a min. of 15 minutes warm up time before adjustment.
7-2. Adjustment Sequence:
FBT B+ Voltage → G2 Voltage → Hor. Center → Hor. Size → Hor. Position → Ver. Size
→ Ver. Position → Side-pin → Trapezoid → Focus → White Balance → Convergence (if
needed).
7-3. Adjustment Procedure - How to enter the Factory Mode:
Press Menu and Down simultaneously and hold down for three seconds. Adjust
BRIGHTNESS and CONTRAST to “50” amplitude. Factory mode is active when the
bottom line of the menu is red. Blue indicates user mode.
7-3.1 FBT B+ voltage adjustment. (Flyback Replacement Only – Pot is Glued)
1.
2.
Input the crosshatch pattern with the 48KHz 1024x768 mode.
After connecting a digital voltmeter to D316, cathode and the frame ground, adjust
FBT B+ voltage to 110V +/- 0.5V using VR301.
7-3.2 G2 and G1 Voltage adjustment.
1.
2.
3.
Input the crosshatch pattern with 48 kHz 1024x768 mode
Adjust the G2 for visible background.
Adjust G1, VR501, for –35 +/- 1vdc
7-3.3 Geometry/Display Adjustment.
Refer to controls and adjustment (Article 6)
7-3.4 Focus Adjustment
1.
2.
Input the “H” character pattern with 48 kHz 1024x768
Adjust the focus for the best balance at each point of A,B,C,D,E as shown below by
rotation the focus VR of FBT
3.
For Dual Focus 17” monitors, adjust FOCUS 1 and FOCUS 2 for sharpest
horizontal and vertical lines on a crosshatch pattern in oval area from point B to
point C of display. Check overall focus in center and corners.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
7-3.5 Purity and Convergence Adjustment. (If Required)
A. Purity Adjustment.
1. Demagnetize the picture tube and cabinet using a degaussing coil.
2. Turn the CONTRAST and BRIGHTNESS controls to maximum.
3. In User Color Menu, adjust RED and BLUE controls to provide only a green raster
4. Loosen the clamp screw holding the yoke and slide the yoke
backward to provide vertical green belt (zone) in the picture screen.
5. Remote the Rubber wedges
.
6. Rotate and spread the tabs of the purity magnet around the neck of the picture tube
until the green belt is in the center of the screen. At the same time, center the raster
vertically.
7. Move the yoke slowly forward until a uniform green screen is obtained. Tighten the
clamp screw of the yoke temporarily.
8. Check the purity of the red and blue raster by adjusting COLOR controls.
9. Obtain a white raster referring to “CRT GRAY SCALE ADJUSTMENT”
10. Proceed with convergence adjustment.
B. Convergence adjustment:
1. Change to a crosshatch pattern with a color signal generator.
2. Adjust the BRIGHTNESS and CONTRAST controls for well defined pattern
3. Adjust two tabs of the 4-pole magnets to change the angle between them and
.
superimpose red and blue vertical lines in the center of the picture screen
.
4. Turn both tabs at the same time keeping their angles constant to superimpose red
and blue horizontal lines at the center of the screen.
5. Adjust two tabs of 6-pole magnets to superimpose red/blue line with green one.
Adjusting the angle affects the vertical lines and rotating both magnets affects the
horizontal line.
6. Repeat adjustments 3,4 and 5, keeping in mind red, green and blue movement,
because 4-pole magnets and 6-pole magnets interact and make dot movement
complex.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
7-3.6 White Balance adjustment (video).
1. Warm up the unit for 15 minutes
2. Input the window pattern with 31KHz 640*480 mode.
3. Adjust the color temperature to be X=0.285+/-0.015 and Y=0.293+/-0.015 by
R.G.B. gain on User Color Menu or User Preference.
7-4
OSD FACTORY CONTROL
This should be adjusted by a technician or qualified repair personnel.
This monitor has two-adjustment modes.
One is for the user’s own adjustment and other is for factory adjustment.
But sometimes adjustments in the factory adjustment modes are needed for repair.
Caution: More precautions must be made in the factory adjustment mode compared to the
user mode, because after finishing adjustments in the factory mode, if wrong values have been
entered, you can not revert back to the old settings. At the user mode, if there are mistakes,
you can use the “RECALL” function (refer to 6-3 M item) to go back to the previous settings.
In factory mode, the “RECALL” function will only display your current settings.
A. Factory mode entering.
Press the “MODE” and “DOWN” key simultaneously until the OSD comes out as below.
The OSD of factory mode is the same format with user mode except for the color of the
bottom line. (User mode is blue; factory mode is red).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
B. Exit and save. (Save is automatic)
1. After finishing adjustments, select “RECALL” using “UP/DOWN” key.
2. Press “SEL” key until OSD disappears. The adjusted value is saved and exits from the
factory mode.
C. Adjustment.
All adjustment methods are same as user’s control mode except “COLOR”
7-5
White balance Adjustment:
A. Pre-adjustment.
1.
2.
3.
Warm up monitor for 15 minutes.
Input the small window pattern with 31KHz 640*480 mode.
Degauss the screen with External degaussing coil.
White Balance adjustment (background raster).
1.
2.
Remove the video signal.
Adjust the sub-brightness of background raster to be 1.0FtL +/- 0.3FtL with SUB
BRIGHTNESS control VR501.
B. COLOR ADJUSTMENT.
COLOR 1 - 8500°K: X=0.285, Y=0.294
COLOR 2 - 6500°K: X=0.312, Y=0.329
Check at 2.5fL (BIAS), 50fL (GAIN) light output levels.
Reference size, Horizontal = 361mm +/- 4 mm from CRT phosphor edges.
Vertical = 270mm +/- 4mm from CRT phosphor edges.
1. It is best to use a centered small white box pattern. Before adjusting the “COLOR”.
“CONTRAST” should be set at the maximum and “BRIGHTNESS” should be set to
“50”.
2. In the factory mode, toggle down to “COLOR” using “UP/DOWN” key.
3. Select “COLOR” by pressing “SEL” key. Color sub-menu appears as left below figure.
4. Search a color temperature you want to adjust (gain or bias) using “UP/DOWN”
(“GAIN” is the high-beam area’s adjustment and “BIAS”, the low-beam.)
5. Select any item desired by pressing “SEL” key then the OSD changes to the sub-menu
as shown in figure below-right.
6. Adjust color temperature using “SEL” and “UP/DOWN” key.
(“SEL” key: moves item position, “UP/DOWN” key: changes value.)
7. In the “GAIN” mode, “CO” means sub-contrast adjustment. Sub-contrast is adjusted
using “UP/DOWN” key.
8. Press the “MODE” key to finish the “GAIN” or “BIAS” adjustment.
9. If you want to adjust other “GAIN” or “BIAS”, repeat from steps 4-8.
10. Press “MODE” key again to finish the “COLOR” adjustment.
11. When done with the factory adjustment, select “RECALL” as in step B.“Exit and
save”.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
7-5
B. Color Adjustment
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
8.DESCRIPTION OF CIRCUIT OPERATION:
8-1. Mode Control.
8-1.1 H-Sync is inputted to pin 30 of IC601, V-Sync to pin 29 of IC601 for each mode and pin
27, 26
of IC601 output always positive polarity sync.
8-1.2 The outputs from IC601 are as below (See table below)
Frequency
Range of Frequency
OUTPUT (MCU PIN)
(CS3) (CS2) (CS1) OFF ST-BY SUS-P LED
No.
Resolution
Hf
Vf
Hf (KHz)
Vf (Hz)
38
39
40
5
3
4
6
KHz Hz
1
2
31
31
35
38
38
47
48
48
53
56
60
64
69
70
60
86
75
60
75
72
60
85
70
75
60
85
720x400
640X480
1024X768
640X480
800X600
800X600
800X600
1024X768
800X600
1024X768
1024X768
1280x1024
1024x768
28 ~32.9
68 ~ 72
58 ~ 62
84 ~ 88
73 ~ 77
58 ~ 62
73 ~ 77
70 ~ 74
58 ~ 62
83 ~ 87
68 ~ 72
73 ~ 77
58 ~ 62
83 ~ 87
L
L
L
L
H
L
L
"
L
H
H
H
H
H
H
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
H
H
H
H
H
H
H
H
H
H
H
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
3
33 ~ 35.9
36 ~ 40.9
36 ~ 40.9
41~ 51.9
"
4
H
H
L
L
5
L
6
H
H
H
H
H
H
H
H
7
L
8
"
L
9
52 ~ 61.9
"
H
H
H
H
H
10
11
12
13
L
"
L
62 ~ 70
62 ~ 70
H
H
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
8-2
Deflection Processor (IC301):
8-2.1
8-2.1.2
Horizontal section.
Horizontal Oscillation.
Horizontal free frequency is set to 48KHz by R314 and C347. Auto-sync processing
can be done from 28KHz to 70KHz by means of IC301 without any adjustment.
8-2.1.3
8-2.1.4
Phase Shift.
Horizontal phase shift is controlled by IC601 using I²C BUS control.
Horizontal driver output.
The output pulse having the duty-cycle of 47% is available at pin 26 of IC301
The output is used by the horizontal drive circuit.
8-2.1.5
8-2.1.6
B+ control driver output.
The output pulse is available at pin 6 of IC301 and it is used for the horizontal scan
voltage control driver.
X-Ray protection.
When the flyback voltage rises up to an unacceptable level, X-ray protection is
activated. When the X-ray input pin 25 of IC301 is above 8V, the internal latch in
IC301 is turned on. This stops all line drive output to the horizontal circuits. To
reset the protection circuit, remove main power to the monitor for 5 seconds.
8-2.2
Vertical section:
8-2.2.1
Vertical oscillation.
The free running frequency of the vertical oscillator is determined by the capacitor
C342 at pin VCAP (pin22) of IC301.
8-2.2.2
8-2.2.3
Vertical amplitude.
Vertical amplitude is controlled by IC601 using I²C bus control.
Vertical position.
Vertical position is controlled by IC601 using I²C bus control.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
8-2.2.4
8-2.3
East-west parabola.
A parabola wave-form is available on pin 24 of IC301 for driving the pincushion
correction stage. Amplitude of parabola waveform is controlled by IC601 using I²C.
B+ Regulator.
B+ PWM regulator output is available on pin 28 of IC301 for driving the B+ control
stage. This PWM output is adjusted through VR301.
8.3
Vertical Deflection (IC201):
IC201 (KA2142) is used for direct driving of the vertical deflection yoke.
Horizontal scan voltage control stage:
8-4
The set-up converter is used in this stage. The output pulse at pin 28 of the IC301 is
synchronized on horizontal frequency. This pulse is operated via buffer stage
Q311/Q312. This output is rectified through D315/L304.
In this way, the supply voltage to the flyback transformer can be proportional to the
horizontal line frequency.
8-5
Horizontal deflection output stage:
8-5.1
Line driver stage.
As a driver device, small MOSFET Q307(IRF630A) is used.
The driver transformer T302 is equipped with a snubber circuit (R327/C309) at the
primary side to damp excessive ringing.
8-5.2
Horizontal power output stage.
The horizontal power output stage is a conventional one with a diode modulator.
As a deflection transistor, the Q308 (KSC3997) is used.
To compensate for horizontal linearity, T301 is connected in series with the
horizontal DY. It is controlled by DC voltage of Q304 collector, which the base
voltage of Q304 is integrated from output at pin 40 of IC601.
8-5.3
S-Correction capacitor switches.
Q316 is off when horizontal frequency is 35KHz
Q316, Q317 are off when horizontal frequency is 37KHz
Q316, Q318 are off when horizontal frequency is 43KHz-52KHz
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
Q317, Q318 are off when horizontal frequency is 53KHz a 61KHz
Q316, Q317, Q318 is off when horizontal frequency is 62KHz a70KHz
8-6
8-7
8-8
FBT (Flyback Transformer):
The high voltage for CRT anode focus, G2 voltage for CRT and – 12V for vertical
deflection are generated by the FBT. Also, -130V for G1 voltage, horizontal flyback
pulse, +128V video supply, and for dual focus units 800V dynamic focus supply.
ABL (Automatic Beam Limiting):
The voltage of point 7 depends on the anode current of FBT. So, the voltage at pin 7
of the FBT decreases with increasing anode current. That time, using at this level,
increase contrast setting level limited a certain level (32FtL in white pattern) that is
set by inner voltage of IC401.
Video amplification section:
8-8.1
Video pre-amplifier(IC401).
Input video signals are amplified by means of IC401, and the amplified signals drive
the video output stage (IC402). Video gain is adjusted by DC voltage at pin 12 for
ABL control.
8-8.2
Video output stage (IC402).
The video output signals from IC401 are amplified again by IC402, and IC402
applies video signals to each cathode of the CRT. Cutoff voltages are adjusted by
Q405, Q406 and Q407 which is operated by I²C BUS control through the
microprocessor.
8-8.3
OSD (On Screen Display : IC403).
The OSD signal is applied from IC403 to IC402. It is controlled by I²C BUS control
line.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
9.
TROUBLESHOOTING:
9-1. NO POWER.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
9-2. NO VIDEO.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
9-3. NO RASTER:
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
9-4
TROUBLE IN HORIZONTAL SIZE:
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
9-5. TROUBLE IN CONTRAST:
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Wells-Gardner Electronics Corporation
9-6. TROUBLE IN BRIGHTNESS:
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|