Installation & Operating Manual
Single stage operation oil burners
RETROFIT APPLICATIONS ONLY
If this burner is being installed in a packaged unit (ie. burner comes with a boiler or furnace), follow
the installation and set-up instructions supplied with the heating unit, as settings may differ from
those shown in this manual.
- The following pages contain information, descriptions and diagrams for the proper installation
and wiring of the burner. Please read carefully before attempting final installation.
- This manual is to remain with the final installation designation. It is the installer’s responsibility to en-
sure that the burner installation and operation instructions mentioned in this manual are followed and
operated within local code authority limits.
RIELLO 40
CODE
MODEL
TYPE
C8512519
C8512520
C8512521
800057000-Brn-PO Rie F5
800058000-Brn-PO Rie F5
800059000-Brn-PO Rie F5
1.00GPH Vnt-C
1.20GPH Vnt-C
1.40GPH Vnt-C
C6501071(0)
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
TABLE OF CONTENTS
PACKAGE CONTENTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SERIAL NUMBER IDENTIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Mounting flange dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
INITIAL SET-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
OIL BURNER COMPONENT IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Burner components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ASSEMBLY OF AIR TUBE TO BURNER CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
MOUNTING BURNER TO BOILER OR FURNACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5
Method 1-Universal Mounting Flange. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Method 2-Semi-flange Collar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Method 3-Pedestal Mount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
AMULET INSTALLATION INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
INTERNAL FACTORY WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
APPLICATION FIELD WIRING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
NOZZLE PLACEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
INSERTION / REMOVAL OF DRAWER ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
ELECTRODE SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
TURBULATOR SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
OIL LINE CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 12
Single line (Gravity feed system) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Two line (Lift system) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PUMP PURGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Single line (Gravity feed system) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Two line (Lift system) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SETTING THE AIR ADJUSTMENT PLATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
BURNER ADJUSTMENT TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
BURNER START-UP CYCLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
EXPLODED SPARE PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SPARE PARTS LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 - 16
3223
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
PACKAGE CONTENTS LIST
Your Riello 40 burner should include the following parts. Please check to make sure all parts are present before begin-
ning the installation.
Quantity Description
Code
1
1
1
1
1
Burner with combustion head mounted
C8512519 - C8512520 - C8512521
Mounting gasket
Parts bag
C6880016
2569525
2569526
C6501071
Parts bag
Installation manual
Separate carton - OEM burners shipped with combustion head mounted
Parts bag 2569525
Parts bag 2569526
Quantity Description
Quantity Description
2
2
2
4
2
Semi-flange bolts (long)
Semi-flanges
Mounting flange bolts (short)
Nuts
Chrome nuts
1
1
1
1
1
1
By-pass plug
Female ¼” NPT adapter
Male 3/8” NPT adapter
2.5 mm Allen key
Oil pump connector (supply)
Oil pump connector (return)
SERIAL NUMBER IDENTIFICATION
Your Riello burner may have been manufactured in more than one location and therefore there are two possible serial
number identification.
(06)
(01)
(12345)
The Riello 9 character serial number, example,
06 01 12345, is identified as follows:
06
01
= Last two digits of the year of manufacture;
= Week of manufacture;
Year of
manufacture
BI-week of
manufacture
Increment
12345 = Increment of 1 for each burner produced – specific
to product code – reset to zero each January 1st.
(06)
(A)
(8511111)
(00025)
The Riello 15 character serial number, example,
06 A 8511111 00025, is identified as follows:
06
= Last two digits of the year of manu-
facture;
= BI-week of manufacture;
Year of
manufacture
BI-week of
manufacture
BI-week of
manufacture
Increment
A
8511111 = Burner product code;
00025 = Increment of 1 for each burner pro-
duced – specific to product code –
reset to zero each January 1st.
3223
1
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
TECHNICAL DATA
SPECIFICATIONS
Fuel
B
No heavier than # 2 fuel oil
F3 Firing rate - Effective Output 0.50 to 0.95 US GPH - 70,000 to 133,000 BTU/h
F5 Firing rate - Effective Output 0.75 to 1.65 US GPH - 105,000 to 231,000 BTU/h
Voltage (single phase)
120V 60Hz (+ 10% - 15%)
F3 Absorbed electrical power 155 Watts
F5 Absorbed electrical power 175 Watts
Motor (rated)
3250 rpm Run Current 2.2 AMP
Capacitor
12.5 Microfarads
130 to 200 psig
RIELLO 530 SE/C
8kV 16mA
Pump pressure
Primary control
Ignition transformer
E
E1
F
BURNER DIMENSIONS
Model
A
B
C
D
E
F
Inches 8 15/32 9 59/64 6 15/32
mm 215 252 164
Inches 9 11/64 10 11/16 7 3/32
mm 233 272 180
3 1/2
89
3 1/2
89
6
152
6
8 29/32
226
9 13/32
239
F3
F5
152
D7352
E1: 10-inch long (254mm) tubes are also available.
BURNER COMPONENTS IDENTIFICATION
1
7
2
3
4
1
5 / ”-140mm
2
6
5
1
7 / ” - 190 mm
2
15
8
/
” - 215 mm
32
D7351
9
BURNER COMPONENTS
8
1
2
3
4
5
6
7
8
9
Lockout indicator lamp and reset button
Primary control
Primary control sub-base
Pump pressure regulator
Motor
Air adjustment and shutter
Electronic air shutter assembly
Combustion head
10
11
12
Semi flange 2 pieces
10 Mounting flange with gasket
11 Supply fuel line port
12 Pump valve (coil)
13 Vacuum gauge port
14 Pressure gauge and bleeder port
15 Return fuel line port
13
14
15
D7304
3223
2
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
INITIAL SET-UP
A) Remove burner and air tube from cartons. Check parts list (inside cover) to ensure all parts are present.
B) Remove burner cover by loosing the three screws securing it. Remove control box and air tube cover.
C) Remove drawer assembly from air tube, insert nozzle and set Turbulator adjustment for specific input required, then
set aside.
D) Mount air tube to burner chassis.
ASSEMBLY OF AIR TUBE TO
BURNER CHASSIS
The air tube and drawer assembly are
shipped in a carton separate from the burner
chassis. Choose the proper air tube length to
obtain the tube insertion for the specific in-
stallation.
A) Remove the AIR TUBE and BURNER
CHASSIS from their respective cartons.
B) Remove the DRAWER ASSEMBLY (1)
S7462
from inside the AIR TUBE by loosening
the screw (2). Carefully pull the DRAWER ASSEMBLY out of the AIR TUBE, install the required nozzle (see page 8)
and set aside.
C) Remove the two BOLTS (3) from FRONT PLATE (4) of the BURNER CHASSIS. Align the two holes on the AIR
TUBE HOLDING PATE (5) with the two holes on the BURNER CHASSIS FRONT PLATE with the BOLTS (3) re-
moved. Replace the BOLTS and fingers tighten only. Re-install DRAWER ASSEMBLY into AIR TUBE. Tighten
SCREW (2) securely.
D) Tighten the two bolts (3) securely.
MOUNTING THE BURNER TO THE BOILER OR FURNACE
There are three possible methods to mount the burner, depending on the individual application. These are:
1) Universal flange bolted to Boiler/Furnace unit.
2) Semi-flange collar bolted to Boiler/Furnace unit.
3) Universal flange mounted to optional Pedestal mount, where flange mounting direct to appliance is not possible.
Pedestal kit must be ordered separately.
METHOD 1 – UNIVERSAL MOUNTING FLANGE
A
DRY BASE
BOILER
B
D6013
A
COMBUSTION
CHAMBER
B
S7461
D6014
3223
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
A) Insert the two BOLTS (1) into the UNIVERSAL MOUNTING FLANGE (10) from the flat side, ensuring the bolt heads
are flush with the flat surface. Secure in place using two special CHROME NUTS (2) provided.
B) Position the MOUNTING GASKET (3) between the flat surface of the UNIVERSAL MOUNTING FLANGE (10) and
the appliance. Line up the holes in the UNIVERSAL MOUNTING FLANGE with the STUDS (4) on the appliance
mounting plate and securely bolt the UNIVERSAL MOUNTING FLANGE to the plate.
C) Secure the two semi-flanges of the ADJUSTABLE COLLAR (9) to the AIR TUBE using the two long BOLTS (6). Be
sure that the ADJUSTABLE COLLAR (9) is properly positioned so the outside edge of the END CONE will be at least
¼ inch (6.5mm) back from the inside wall of the refractory of the combustion chamber (see dimension B above). The
measured length (A) is to include MOUNTING GASKET and FLANGE, if used.
D) The burner may now be attached to the heating unit by insetting the AIR TUBE through the BURNER ACCESS
HOLE (8) and into the appliance, making sure the BOLTS (1) line up with the two HOLES (5) in the ADJUSTABLE
COLLAR (9). Secure the burner in place using two NUTS (7).
A visual verification of the air tube insertion into the combustion chamber of the heating unit is suggested. Dimension B
should be at least ¼” (see drawing).
NOTE:
A suggested method for creating mounting bolt holes in the mounting gasket: Hold the gasket against the appliance
mounting bolts using the mounting flange for proper positioning. Lightly tap the flange with a hammer to form the holes.
METHOD 2 – SEMI-FLANGE COLLAR
A) Follow item C from METHOD 1.
B) Align the air tube and attached adjustable collar so air tube is centered in the burner access hole of the boiler/fur-
nace unit. Mark the center of the two holes in the ADJUSTABLE COLLAR on to the front plate of the heating unit.
Then drill ¼ inch (6.5mm) holes through the front plate of the unit, using marks as a guide.
C) Install two short BOLTS (1) through the front plate of the heating unit from the inside, and secure on the outside us-
ing the two special CHROME NUTS (2).
D) Follow item D from METHOD 1.
METHOD 3 – PEDESTAL MOUNT
Secure the MOUNTING FLANGE to MOUNTING PEDESTAL using the hardware provided with the pedestal. Secure
burner to MOUNTING FLANGE as in METHOD 1, item A, C and D.
NOTE:
It is suggested that the pedestal be anchored in position on the floor by installing brackets over the pedestal tube and
securing brackets to the floor.
WARNING:
WHEN THE COMBUSTION CHAMBER IS LINED WITH A REFRACTORY MATERIAL, IT IS IMPERATIVE THAT
THE END CONE NOT PROTRUDE INTO THE CHAMBER AREA, AS EXCESSIVE HEAT AT BURNER SHUT
DOWN WILL DAMAGE THE END CONE.
3223
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
AMULET INSTALLATION INSTRUCTIONS
(Required on some models)
Amulet shown in the
flush mounted position
The amulets provided have been selected by Riello to protect the
combustion tube from hot exhaust gases and flame. This protec-
tion may be needed in applications where the combustion tube
opening in the combustion chamber refractory is larger than the
tube outside diameter.
The amulet has been sized to fit Riello Model 40 sizes F3 and F5
plus the Riello Model R35.
When installing this amulet, handle it carefully.
Do not exert undue pressure when pushing the amulet over the
combustion tube.
Head receeded
1/4 inch max.
D7285
Excessive force can result in a broken amulet!
If the amulet will not fit easily onto the tube, remove a small amount
of the inner diameter with a sharp knife to provide the necessary clearance.
The diagram below shows the proper position of the amulet after installation.
NO AMULET
AMULET
FLUE GASES
FLUE GASES
Tapered combustion
chamber causes increase
in pressure inside
Tapered combustion
chamber causes increase
in pressure inside
LOW PRESSURE
LOW PRESSURE
HEAT
HIGH PRESSURE
HEAT
AIR TUBE
AIR TUBE
HIGH PRESSURE
HEAT
HEAT
Increase in pressure
down air tube due
to increase in
combustion chamber
pressure
Increase in pressure down
air tube due to increase
in combustion chamber
pressure
Amulet helps prevent
not gases from
travelling down
air tube
Increase in pressure down
air tube due to increase
in combustion chamber
pressure
S7941
3223
5
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
INTERNAL FACTORY WIRING
RIELLO 40 F3 - F5 SERIES OIL BURNERS EQUIPPED
WITH AN ELECTRONIC AIR SHUTTER
INTERNAL FACTORY WIRING
PUMP VALVE
(COIL)
MOTOR
D7328
CAPACITOR
Key to lay-out:
A - Brown
B - White
C - Blue
6
- 120V source activates shutter open
- motor lead 120V source
11
- 120V control lock out alarm terminal
D - Black
AUX - costant 120V auxiliary terminal - electronic air shutter
ATTENTION !!
³
Do not swap neutral and phase over, follow the diagram shown carefully and carry out a good earth
connection.
³
³
Minimum wire size AWG 18.
All wiring must be done in accordance with existing codes, both national and local.
3223
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
APPLICATION FIELD WIRING
WIRING DIAGRAM SHOWN BELOW FOR STANDARD RIELLO 530 SE/C PRIMARY CONTROL BOX.
INSTALLATION NOTE: ELECTRONIC AIR SHUTTER REQUIRES A CONSTANT 120V POWER SUPPLY TO
THE AUX TERMINAL, FAILURE TO PROVIDE THIS WILL RESULT IN NO BURNER OPERATION OR AIR SHUT-
TER WILL NOT CLOSE.
AIR SHUTTER
MOTOR
AIR SHUTTER
MOTOR
PLEASE NOTE: OPERATING LIMIT AND SAFETY LIMIT ARE TWO SEPARATE LIMITS.
Key to lay-out:
1
2
3
4
5
6
- Main disconnect fuse
- Manual service switch
- Safety limit device
- Operating limit device
- Earth ground connection burner chassis
- Burner control remote lock out alarm device - wired & supplied by others
AUX - Auxiliary bub base add-on connector (air shutter)
T - T - 24V thermostat connections - low voltage operated system
MIN. WIRE SIZE:
INSULATED 18 AWG SOLID OR 16 STRD.
PROPER EARTH GROUNDING MEANS REQUIRED
RATED 105° C
ALL WIRING SHOWN PROVIDED BY OTHER.
WARNING: DO NOT activate burner until proper oil line connections have been made, or failure of the pump
shaft seal may occur.
WARNING: DO NOT activate burner until all safety and operating controls have been wired in series with the
burner, as required by local code authorities and/or as specified by the appliance manufacturer.
3223
7
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
NOZZLE PLACEMENT
A) Determine the proper firing rate for the boiler or furnace units,
considering the specific application, and then use the Burner
Setup charts on page 12 to select the proper nozzle and pump
pressure to obtain the required input from the burner.
B) Remove the NOZZLE ADAPTER (2) from the DRAWER AS-
SEMBLY by loosening the SCREW (1).
C) Insert the proper NOZZLE into the NOZZLE ADAPTER and
tighten securely (Do not over tighten).
D) Replace adapter, with nozzle installed, into drawer assembly
and secure with screw (1).
S7459
INSTALLATION/REMOVAL
OF DRAWER ASSEMBLY
Removal:
A) Loosen off oil delivery tube nut
from pump.
B) Loosen SCREW (3), and then un-
plug CONTROL BOX (1) by care-
fully pulling it back and then up.
C) Remove the AIR TUBE COVER
PLATE (5) by loosening the re-
taining SCREW (4) (Two
SCREWS – Model F5).
D) Loosen SCREW (2), and then
slide the complete drawer assem-
bly out of the combustion head as
shown.
E) To insert drawer assembly, re-
verse the procedure in items A to
D above.
S7460
5/32” or 4 mm
ELECTRODE SETTING
IMPORTANT:
These dimensions must be observed and verified.
D6003
5/32” to 13/64” or 4 to 5 mm
TURBULATOR SETTING
3
2
1
A) Loosen NUT (1), and then turn SCREW (2) until the INDEX MARKER
(3) is aligned with the correct index number as per the Burner Setup
charts, or OEM specifications given with the appliance.
B) Retighten the RETAINING NUT (1).
NOTE: OEM specifications take priority over retrofit specifications
shown in this manual.
MODEL F3: Zero and three are scale indicators only. From left to
right the first line is 3 and the last line 0.
D5997
MODEL F5: Same as above, except scale indicators are 0 and 4.
3223
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
OIL LINE CONNECTIONS
This burner is shipped with the oil pump set to operate on a single line system.
To operate on a two-line system the by-pass plug must be installed.
WARNING: Do not operate a single line system with the by-pass plug installed. Operating a single line system with
the by-pass plug installed will result in damage to the pump shaft seal.
NOTE: Pump pressure must be set at time of burner start-up. A pressure gauge is attached to the PRESSURE PORT
(8) for pressure readings. Two PIPE CONNECTORS (6) are supplied with the burner for connection to either a single or
two-line system. Also supplied are two ADAPTORS (3), two female ¼” NPT, to adapt oil lines to burner pipe connectors.
All pump port threads are British Parallel Thread design. Direct connection of NPT threads to the pump will damage
the pump body.
Riello manometers and vacuum gauges do not require any adapters, and can be safely connected to the pump ports.
An NPT (metric) adapter must be used when connecting other gauge models.
1
8
2
3
5
6
7
4
4
SINGLE LINE (GRAVITY FEED SYSTEM)
A) The burner is shipped configured for use in single line applications. No changes to the oil pump are required for use
in single line applications.
NOTE: If the pump cover (1) is removed for any reason, be sure the O-ring (2), is properly seated in the pump cover
(1) before re-attaching the pump cover to the pump housing.
B) Connect the pipe connector to the SUPPLY PORT(5) of the pump. Attach the NPT adapter to the pipe connector.
Attach the required piping to this pipe adapter. Be sure that the plug in the RETURN PORT (7) is tightened securely.
SINGLE LINE SYSTEM-PIPE LENGTHS
H
3/8” OD
1/2” OD
FT
1.5
3.0
5.0
6.5
M
FT
M
FT
M
20
0.5
1.0
1.5
2.0
33
65
10
20
40
60
65
ATTENTION:
do not exceed
pipe lengths
130
260
325
40
130
195
80
indicated in chart!
100
D6009
3223
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
TWO LINE (LIFT SYSTEM)
A) If a two-line system is required, install the By-pass plug provided. The by-pass plug is installed in the return port
of the pump. A 2.5-mm hexagonal key provided with the by-pass plug is to be used to install the plug.
DO NOT use an inch size hexagonal key; damage to the by-pass plug may result.
When operating on a two-line system, supply and return lines should be the same diameter and both should
extend to the same depth inside the fuel tank. Be sure there are no air leaks or blockages in the piping sys-
tem. Any obstructions in the return line will cause failure of the pump shaft seal.
2 LINE (LIFT) SYSTEM-PIPE LENGTHS
H
3/8” OD
1/2” OD
FT
0.0
1.5
3.0
5.0
6.5
9.5
11
M
FT
M
35
30
25
20
15
8
FT
M
100
100
100
90
70
30
20
0.0
0.5
1.0
1.5
2.0
3.0
3.5
115
100
80
65
50
330
330
330
295
230
100
65
ATTENTION:
do not exceed
pipe lengths
indicated in chart!
25
20
D6008
6
To install the by-pass plug:
1) Remove the return plug (7).
2) Install the by-pass plug (4) using the 2.5 mm hexagonal key.
B) Attach the two PIPE CONNECTORS (6) to the pump SUPPLY and pump RETURN PORTS (5 and 7). Attach the
required piping to these two pipe connectors using the NPT/ METRIC ADAPTERS that are supplied with the burner.
WARNING:
- Pipe dope or Teflon tapes are NOT to be used on any direct oil connection to the fuel pump.
- The height ‘P’ in Pipe Length Charts should not exceed 13 feet (4 m).
- The vacuum should not exceed 11.44 inches of mercury.
IMPORTANT:
An external, appropriately listed and certified oil filter must be placed in the fuel line between the fuel tank
and the burner pump.
PUMP PURGE
NOTE: To protect the pump gears, it is advisable to lubricate the pump prior
to purging a lift system. Apply oil through the VACUUM PORT (C).
B
C
A) SINGLE LINE (GRAVITY FEED SYSTEM)
I. Loosen the bleeder valve (A) until oil flows out. Tighten the bleeder valve
securely and startburner.
II. When bleeding the pump by pressure:
1) Loosen the bleeder valve (A).
2) Disconnect nozzle oil supply line at the pump nozzleport (B).
3) Attach a flexible plastic tube to the pump nozzle, port directing the oil
flow into a bucket.
4) Loosen the screw(s) securing the air tube cover, allowing it to be re-
moved freely.
5) Holding the air tube cover in its proper location start the burner.
6) When the solenoid valve is engaged approximately 10 seconds after
starting, remove the air tube cover and shine a light source on the
photocell, allowing it to see false light.
A
D7284
3223
10
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
7) Run the burner until the fuel pump has been purged of air, then tighten the bleeder valve and immediately
shut down the burner.
8) Reinstall the air tube cover and nozzle line.
9) The burner can now be started normally.
WARNING: Omitting steps 2 and 3 will result in a collection of unburned oil in the combustion chamber creating a haz-
ardous situation upon burner startup.
B) TWO LINE (LIFT SYSTEM)
Turn off the main power source to the burner and remove the air tube cover.
Shines a light source on the photocell (now visible where the air tube cover was removed), return power to the burner
and activate the burner. With the light source in place, the burner will operate in prepurge only. When the pump is suffi-
ciently purged, the hydraulic air shutter will open.
Once the burner is purged, turn off the power source and replace the air tube cover.
Return power to the burner. The burner is now ready to operate.
ATTENTION:
It is important that the fuel line be completely sealed and free from air leaks or any internal blockages.
WARNING! WHEN THE BYPASS PLUG IS INSTALLED, A TWO-PIPE SYSTEM MUST BE USED OR FAILURE OF
THE PUMP SHAFT WILL OCCUR.
SETTING THE AIR ADJUSTMENT PLATE
1
The electronic air shutter assembly (1) is operated on a
120V 60Hz. motor, and the burner motor will not operate un-
til the air shutter is in its fully open position.
Set the air plate (4) setting according to OEM setup informa-
2
3
5
4
tion or by following the Retrofit settings listed in this manual.
To adjust the air plate (4) to the desired set point indicator
(2), loosen the center air shutter assembly screw (5) and
loosen the side air plate screw (3), move air plate (4) by us-
ing the air plate adjust arm. After adjustments are made
please retighten screws (3) & (5).
The final position of the air adjustment plate will vary on
each installation. Using proper combustion test instruments
to establish the proper setting of the air gate setting to
achieve safe and efficient results according the appliance
information or if not available.
D7305
NOTE: Variations in flue gas, smoke, CO2 and temperature readings may be experienced when burner cover is put
in place. Therefore, the burner cover must be in place when making final combustion instrument readings, to ensure
proper test results are obtained.
3223
11
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
BURNER ADJUSTMENT TABLE
NON-RETROFIT APPLICATIONS
If this burner is being installed in a packaged unit (i.e. Burner comes with a boiler or furnace), follow the instal-
lation and set-up instructions supplied with the heating appliance, as settings will differ from those shown in
this manual.
RIELLO BURNER SET UP SHEET
Weil McLain Part No.
Riello Part No.
8000-5700
C8512519
8000-5800
8000-5900
C8512520
F5 Factory
preset *1
UO4
C8512521
F5 Factory
preset *1
UO5
Riello 40
F5 Factory
preset *1
UO3
F5
Burner Model
Series
Boiler
UO3
0,8
Input
GPH
1,0
1,2
1,4
Nozzle
Delavan
.65 X 70°B
.85 X 60°B
1.00 X 70°B
1.10 X 70°B
Pump Pressure
PSI
150
145
145
160
Turbolator Setting
Air Gate Setting
0
2.75
8
1
2.8
8
3
2.9
8
4
2.9
8
Air tube length
inches
Ait tube insertion
inches
4 1/4"
4 1/4"
4 1/4"
4 1/4"
*1 Nozzle pre-installed at factory.
NOTE:
The above set up charts are a starting point only.
The burner and appliance must be properly set up using proper combustion testing equipment.
Note: Any approved oil burner nozzle type, angle and manufacturer maybe used, as long as input is corresponding the
correct BTU/hr. or US gph input rating of the appliance.
COMBUSTION CHAMBER
Follow the instructions furnished by the boiler/furnace manufacturer. Size retrofit application according to the appropri-
ate installation codes (e.g. CSA B139 or NFPA #31).
BURNER START-UP CYCLE
Normal
Lock-out, due to light-failure
Thermostat
Motor
Ignition transformer
Valve
Flame
Lock-out lamp
D5229
~ 12s
~ 12s
~ 5s
3223
12
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED SPARE PARTS LIST
35
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SPARE PARTS LIST
No.
CODE
F5 DESCRIPTION
No.
CODE
F5 DESCRIPTION
OPTIONAL
60
61
C7001085
C7001033
•
•
TYPE L 24V SWITCHING RELAY
AMULET - CERAFELT SLEEVE KIT
1
2
3
4
5
6
7
8
9
C8111227
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
BURNER BACK COVER
PIPE CONNECTOR - SUPPLY
3/8” NPT/METRIC ADAPTER - MALE
PIPE CONNECTOR - RETURN
1/4” NPT/ METRIC ADAPTER - FEMALE
CRUSHABLE METAL WASHER
BLEEDER
O-RING - PUMP PRESSURE REGULATOR
REGULATOR SCREW
O-RING - PUMP COVER
PUMP SCREEN
3006992
3006571
3006993
3005847
3007077
3007568
3007028
3007202
3007943
•
CAPILLARY PORT PLUG
10 3007162
11 3005719
12 3006925
13 3007203
14 3007029
15 3007156
16 3007268
17 3007087
18 3001157
19 3002278
20 3006553
21 3002279
22 3007802
23 3000443
24 3005843
C7010002
VALVE STEM
VALVE STEM PLATE
O-RING - VALVE STEM UPPER
O-RING - VALVE STEM LOWER
NOZZLE OUTLET FITTING
CRUSHABLE METAL WASHER 5/8” ID
PRIMARY CONTROL 530SE/C
PRIMARY CONTROL SUB BASE
COIL U-BRACKET AND KNURLED NUT
COIL
C7001029
PUMP
PUMP DRIVE KEY
MOTOR
25 3007316
26 3002280
27 3005854
29 3020248
30 3005708
31 3005844
•
•
•
•
•
•
AIR TUBE COVER
PHOTOCELL
SEMI FLANGE (2 REQUIRED)
MOUNTING GASKET
FAN
CAPACITOR 12.5 µF
32 3007320
33 3007204
34 3020249
•
•
•
ACOUSTIC LINER
MANUAL AIR SHUTTER
ELECTRONIC AIR SHUTTER
35
C7001082
•
F5 REPLACEMENT AIR DAMPER KIT
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPARE PARTS LIST
No.
CODE
F5 DESCRIPTION
40
C7001331
•
•
F5 SBT WELDED 4.25" COMPLETE
41 3006968
TURBULATOR DISC
42 3006966
43 3006965
•
•
ELECTRODE SUPPORT
NOZZLE ADAPTER
44 3008629
45 3008634
•
•
NOZZLE OIL TUBE
REGULATOR ASSEMBLY
46 3008631
47 3005869
•
•
ELECTRODE ASSEMBLY
ELECTRODE PORCELAIN
48
C7001335
•
F5 SBT WELDED 4.25" TUBE ONLY
15
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
35 Pond Park Rd.
Hingham, MA 02043
Phone: 781-749-8292
Toll Free: 800-992-7637
Fax: 781-740-2069
2165 Meadowpine Blvd.
Mississauga,On L5H 3R2
Phone: 905-542-0303
Toll Free: 800-387-3898
Fax: 905-542-1525
BURNER START- UP FORM *
Burner S/N. or Model:
Installer name:
Company:
Appliance:
Installation date:
Fax:
Address:
Phone:
Owner Name:
Address:
Phone:
E-mail:
Burner Start-up Info (OIL)
Nozzle info:
Air setting:
Pump pressure:
Turbolator setting:
Draft breech:
Draft overfire:
CO2:
CO:
O2:
Two lines:
Smoke density:
(Bacharach)
Single line:
Thisform wasdesigned and provided in the installation manual for reference and also forproviding tech-
*
nical information which can be faxed or mailed to our technical hot-line coordinator when technical assis-
tance is required. Please complete this form, fax it or mail it at the address/fax above, or send an e-mail
with the information listed below to: [email protected]
3223
Download from Www.Somanuals.com. All Manuals Search And Download.
35 Pond Park Road
Hingham, MA 02043
Phone 781-749-8292
Toll Free 800-992-7637
Fax 781-740-2069
2165 Meadowpine Blvd
Mississauga, ON L5N 6H6
Phone 905-542-0303
Toll Free 800-387-3898
Fax 905-542-1525
Technical Support Hotline
1-800-4-RIELLO
1-800-474-3556
Download from Www.Somanuals.com. All Manuals Search And Download.
|