GOLD CGs
G a s - Fir e d W a t e r B o ile r
Us e r ’s
In fo r m a t io n
M a n u a l
If the information in this manual is not followed exactly, a fire or
explosion may result, causing property damage, personal injury or
loss of life.
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
•
•
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your
building.
•
•
Immediately call your gas supplier from a neighbor’s phone. Follow
the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency
or the gas supplier.
Part No.550-110-261/0999
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
STOP!! — Read before proceeding
Failure to adhere to the guidelines on this page can result in se-
vere personal injury, death or substantial property damage.
Boiler service and maintenance —
•
To avoid electric shock, disconnect electrical supply before per-
forming maintenance.
•
•
To avoid severe burns, allow boiler to cool before performing main-
tenance.
You must maintain the boiler as outlined in the manual and have the
boiler started up and serviced at least annually by a qualified
service technician to ensure boiler/system reliability.
Boiler operation —
•
Do not block flow of combustion or ventilation air to boiler. This
boiler is equipped with a control which will automatically shut down
the boiler should air or vent be blocked. If vent or air blockage is
easily accessible and removable, remove it. The boiler should attempt
to restart within an hour. If blockage is not obvious or cannot be re-
moved, have the boiler and system checked by a qualified service tech-
nician.
•
•
Should overheating occur or gas supply fail to shut off, do not
turn off or disconnect electrical supply to pump. Instead, shut off
the gas supply at a location external to the appliance.
Do not use this boiler if any part has been under water.Immedi-
ately call a qualified service technician to inspect the boiler and to
replace any part of the control system and any gas control, which has
been under water.
•
Have the building monitored when it is vacant for an extended
period. Safety controls can shut down the boiler at any time. The loss
of heat can result in significant damage due to freezing.
Boiler water —
•
DO NOT use petroleum-based cleaning or sealing compounds in
boiler system. Water seal deterioration will occur, causing leakage be-
tween sections and damage to heating system components. This can
result in substantial property damage.
•
•
DO NOT use "homemade cures" or "boiler patent medicines".
Serious damage to boiler, personnel and/or property may result.
Continual fresh makeup water will reduce boiler life. Mineral build-
up in sections reduces heat transfer, overheats cast iron, and causes
section failure. Addition of oxygen and other gases can cause internal
corrosion. Leaks in boiler or piping must be repaired at once to pre-
vent makeup water.
•
Do not add cold water to hot boiler. Thermal shock can cause sec-
tions to crack.
Part No.550-110-261/0999
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
Prevent combustion air contamination
Air contamination
Common household and hobby products often con- age and presenting a possible threat of flue gas spillage
tain fluorine or chlorine compounds. When these into the building.
chemicals pass through the boiler,they can form strong Please read the information below. If the contaminat-
acids in the vent system or boiler. The acid can eat ing chemicals will be present, have your installer pipe
through the vent or boiler wall, causing serious dam- the boiler air from outside per the Boiler Manual.
If the boiler is installed in any area likely to cause contamination, or if products which
would contaminate the air cannot be removed, you must pipe combustion air to the boiler
air intake. Contaminated combustion air will damage the boiler and vent system, resulting in
possible severe personal injury, death or substantial property damage.
Do not operate a CGs boiler in a laundry room or pool facility, for example, without
using ducted outside air. These areas will always contain contaminants.
Products to avoid
Areas likely to have contaminants
Spray cans containing chloro/fluorocarbons
Permanent wave solutions
Dry cleaning/laundry areas and establishments
Swimming pools
Chlorinated waxes/cleaners
Metal fabrication plants
Beauty shops
Chlorine-based swimming pool chemicals
Calcium chloride used for thawing
Sodium chloride used for water softening
Refrigerant leaks
Refrigeration repair shops
Photo processing plants
Auto body shops
Paint or varnish removers
Plastic manufacturing plants
Furniture refinishing areas and establishments
New building construction
Remodeling areas
Hydrochloric acid/muriatic acid
Cements and glues
Antistatic fabric softeners used in clothes dryers
Chlorine-type bleaches, detergents, and cleaning
solvents found in household laundry rooms
Garages with workshops
Adhesives used to fasten building products and
other similar products
4
Part No.550-110-261/0999
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
Maintain boiler using schedule below
Service technician
Owner maintenance
(covered in CGs Boiler Manual —
(see following pages for instructions)
for use only by a qualified service technician)
• Check boiler area
• Check air openings
Inspect:
• Reported problems
Daily
• Boiler area
• Check boiler pressure/
temperature gauge
• Air openings
• Flue gas vent system (and air piping)
• Pilot and main burner flames
• Water piping
• Check boiler interior piping
• Check venting system
• Check air vents
• Boiler heating surfaces
• Burners, base and inlet air box
• Condensate drain system
Monthly
• Check boiler relief valve
• Check condensate drain system
Service:
• Check automatic air vents (if
used)
• Inducer motor
• Oiled-bearing circulators
• Test low water cutoff (if used)
Start-up:
Periodically
• Clean vent termination/air intake
screens
• Perform start-up per manual
Check/test:
• Oil inducer motor
• Operate relief valve
• Gas piping
Every 6 months
• Cold fill and operating pressures
• Air vents and air elimination
• Limit controls and cutoffs
• Expansion tank
• Boiler relief valve
End of season
• Shut down procedure
Review:
• Review with owner
Part No.550-110-261/0999
5
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
User maintenance procedures
❏ B o i l e r m u s t b e s e r v i c e d & m a i n t a i n e d
The boiler should be inspected and started annually, at the beginning of
the heating season, only by a qualified service technician. In addition, the
maintenance and care of the boiler designated on page 5 and explained on
the following pages must be performed to assure maximum boiler effi-
ciency and reliability. Failure to service and maintain the boiler and sys-
tem could result in equipment failure, causing possible severe personal
injury, death or substantial property damage.
The following information provides detailed instructions for completing
the maintenance items listed in the maintenance schedule, page 5. In ad-
dition to this maintenance, the boiler must be serviced and started up at
the beginning of each heating season by a qualified service technician.
❏ C h e c k d a i l y . . . . . . . . . . . .
this manual. If any of these products are in the
room from which the boiler takes its combustion
Check boiler area
air, they must be removed immediately or the
boiler combustion air must be supplied from out-
side. See WARNING above.
To prevent potential of severe personal injury, death
or substantial property damage, eliminate all materials
discussed below from the boiler vicinity. If contami-
nants are found:
Remove products immediately from the area. If they
have been there for an extended period, call a qualified
service technician to inspect the boiler and vent sys-
tem for possible damage from acid corrosion.
If products cannot be removed, immediately call a
qualified service technician to install an outside com-
bustion air source for the boiler (if not already in-
stalled).
Check air openings
1. Verify that combustion and ventilation air open-
ings to the boiler room and/or building are open
and unobstructed.
2. Verify that boiler vent discharge and air intake are
clean and free of obstructions. Remove any debris
on the air intake or flue exhaust openings.
1. Combustible/flammable materials — Do not store
combustible materials, gasoline or any other flam-
mable vapors or liquids near the boiler. Remove
immediately if found.
Check boiler pressure/
temperature gauge
1. Make sure the pressure reading on the boiler pres-
sure/temperature gauge does not exceed 24 psig.
Higher pressure may indicate a problem with the
expansion tank.
2. Air contaminants — Products containing chlorine
or fluorine, if allowed to contaminate the boiler
intake air, will cause acidic condensate in the vent
and boiler. This will cause significant damage to
the vent and/or boiler if allowed to continue. Read
the list of potential materials listed on page 4 of
Contact a qualified service technician if problem
persists.
6
Part No.550-110-261/0999
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
User maintenance procedures continued
❏ C h e c k m o n t h l y . . . . . . . . . . . .
Check boiler interior piping
Check boiler relief valve
1. Remove boiler jacket top.
1. Inspect the boiler relief valve (see Figure 1) and
the relief valve discharge pipe for signs of weeping
or leakage.
2. Visually inspect for leaks around internal piping,
circulators, relief valve and other fittings. Immedi-
ately call a qualified service technician to repair any
leaks.
2. If the relief valve often weeps, the expansion tank
may not be working properly. Immediately con-
tact your qualified service technician to inspect the
boiler and system.
Have leaks fixed at once by a qualifed service techni-
cian. Continual fresh makeup water will reduce boiler
life. Minerals can build up in sections, reducing heat
transfer, overheating cast iron, and causing section fail-
ure.
Do not use petroleum-based cleaning or sealing com-
pounds in boiler system. Severe damage to boiler and
system components can occur, resulting in possible
severe personal injury, death or substantial property
damage.
Check condensate drain system
1. Inspect condensate drain fittings and tubing.Verify
that condensate can flow freely to drain.
Check automatic air vents (if
used)
1. See Figure 2.
Check venting system
2. Remove the cap from any automatic air vent in
the system and check operation by depressing valve
B slightly with the tip of a screwdriver.
1. Visually inspect the flue gas vent piping for any
signs of blockage, leakage or joints or deteriora-
tion of the piping. Notify your qualified service
technician at once if you find any problem.
3. If the air vent valve appears to be working freely
and not leaking, replace cap A, twisting all the way
on.
Failure to inspect the vent system as noted above and
have them repaired by a qualifed service technician can
result in vent system failure, causing severe personal
injury or death.
4. Loosen cap A one turn to allow vent to operate.
5. Have vent replaced if it does not operate correctly.
Figure 1 — Relief valve
Figure 2 —Automatic air vent
Part No.550-110-261/0999
7
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
User maintenance procedures
❏ S e r v i c e p e r i o d i c a l l y . . . . . . . . . . . .
Clean vent termination & air
intake screens
service technician to inspect the boiler and vent/
air systems.
1. Remove all lint and debris from both the boiler air
intake screen and the flue discharge screen.
Test low water cutoff (if
installed)
2. The boiler control module will sense blockage of
the air intake or flue and lockout if the blockage is
excessive. It will signal the failure by flashing the
1. If the system is equipped with a low water cutoff,
appropriate indicator lights on the control board.
test the low water cutoff periodically during the
3. If removing the debris does not allow the boiler to
operate correctly afterwards, contact your qualifed
heating season, following the low water cutoff
manufacturer’s instructions.
❏ S e r v i c e e v e r y 6 m o n t h s . . . . . . . . .
Operate boiler relief valve
charge pipe to ensure that the valve does not weep
after the line has had time to drain. If the valve
weeps, lift the seat again to attempt to clean the valve
seat. If the valve continues to weep afterwards, con-
tact your qualified service technician to inspect the
valve and system.
1. Before proceeding, verify that the relief valve out-
let has been piped to a safe place of discharge, avoid-
ing any possibility of scalding from hot water.
To avoid water damage or scalding
due to valve operation, a metal dis-
charge line must be connected to
relief valve outlet and run to a safe
place of disposal. This discharge line
must be installed by a qualifed
heating installer or service techni-
cian in accordance with the instruc-
tions in the Boiler manual. The
discharge line must be terminated
so as to eliminate possibility of se-
vere burns should the valve dis-
charge.
5. If water does not flow from the valve when you lift
the lever completely,the valve or discharge line may
be blocked. Immediately shutdown the boiler, fol-
lowing the instructions on the inside jacket top
Lighting Instructions. Call your qualified service
technician to inspect the boiler and system.
Oil inducer motor
1. Use only S.A.E. 20 motor oil. DO NOT use house-
hold universal oils.
2. Read the boiler pressure/temperature gauge to
make sure the system is pressurized.
Use only S.A.E. 20 motor oil to lu-
bricate the inducer motor. Do not
use common universal household
oils.
3. Lift the relief valve top lever slightly, allowing wa-
ter to relieve through the valve and discharge pip-
ing.
4. If water flows freely, release the lever and allow the 2. Place a few drops of oil in each of the two oiler
valve to seat. Watch the end of the relief valve dis- cups on the inducer motor.
8
Part No.550-110-261/0999
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
User maintenance procedures continued
❏ E n d - o f - s e a s o n s h u t d o w n . . . . . . . .
Follow boiler shutdown procedure
1. Follow “TO TURN OFF GAS TO APPLIANCE” on the Lighting in-
structions on the inside of the jacket top panel. You will also find
these instructions on pages 12 and 13 of this manual. Use the Lighting
instruction for the gas valve model installed on the boiler.
2. Do not drain system unless exposure to freezing temperatures will
occur.
3. Do not drain the system if it is filled with an antifreeze solution.
4. Do not shut down boilers used for domestic water heating. They must
operate year-round.
Part No.550-110-261/0999
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
How the boiler works . . .
Co n t ro l m o d u le
❏
The control module responds to signals from the room thermostat, air pressure switch and
boiler limit circuit to operate the boiler circulator, pilot burner, gas valve and inducer. When
room thermostat calls for heat, the control module starts the system circulator and inducer.
The control module runs the inducer long enough to purge the boiler flue passages, then
opens the pilot valve and activates pilot ignition spark.
The control module allows up to 15 seconds to establish pilot flame. If flame is not sensed
within 15 seconds, the control module will turn off the gas valve, flash the Flame light, and
then enter a 15-second postpurge. The control module will then start a new cycle. This will
continue indefinitely until pilot flame is established or power is interrupted. Once pilot flame
is proven, the control module opens the gas valve to allow main burner flame.
When the room thermostat is satisfied, the control module turns off the gas valve, operates
the inducer for a 15-second postpurge and waits for the next heat call.
The control module indicator lights show normal sequence when the lights are on steady.
When a problem occurs, the control module flashes combinations of lights to indicate the
most likely reason for the problem.
Tra n s fo rm e r
❏
❏
The control transformer reduces line voltage to 24 volts for the gas valve and limit circuit.
In d u c e r
The inducer pulls flue gases through the boiler, causing air to be pulled in through the air
intake opening. The inducer pushes the flue gases through the vent pipe as well.
Air p re s s u re s w it c h
❏
❏
❏
The air pressure switch signals the control module, telling the control module whether air is
moving through the inducer.
Wa t e r t e m p e ra t u re lim it s w it c h
The water temperature limit switch turns off the gas valve if the temperature in the boiler
goes above its setting. (The circulator will continue to run as long as there is a call for heat.)
Bo ile r c irc u la t o r
The boiler circulator circulates water through the external (system) piping. NOTE — The
control module provides a pump exercising routine. If the boiler is not operated for 30 days,
the control module will power the circulator for 30 seconds, then off.
Ot h e r b o ile r c o m p o n e n t s :
a
b
c
d
e
supply to system
return from system
combustion air inlet
flue outlet
f
pressure/temperature gauge
relief valve (not visible)
air vent connection
flame rollout switch
air inlet box
k
l
pilot burner and bracket
stainless steel burners
g
h
i
m cast iron boiler sections
n
o
flue collector
junction box
gas valve
j
10
Part No.550-110-261/0999
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
GOLD CGs Gas-Fired Induced-Draft Water Boiler
Part No.550-110-261/0999
11
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
Lighting instructions
Before attempting to start the boiler, check the boiler
pressure temperature gauge.
If boiler and system are full of water and properly pres-
surized, the gauge should read at least 12 psig on most
systems.
Operating the boiler without proper water content will
damage boiler and controls and could result in severe
personal injury, death or substantial property damage.
12
Part No.550-110-261/0999
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
Lighting instructions
FOR YOUR SAFETY READ BEFORE OPERATING
If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
A. This appliance does not have a pilot. It is
C. Use only your hand to turn the gas control knob. Never use
tools. If the knob will not turn by hand, don't try to repair it,
call a qualified service technician. Force or attempted repair
may result in a fire or explosion.
equipped with an ignition device which auto-
matically lights the burner. Do not try to light
the burner by hand.
B. Before OPERATING, smell all around the ap-
pliance area for gas. Be sure to smell next to the
floor because some gas is heavier than air and
will settle on the floor. See below.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control, which has been under water.
WHAT TO DO IF YOU SMELL GAS
•
•
Do not try to light any appliance.
•
Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
Do not touch any electric switch; do not use
any phone in your building.
•
If you cannot reach your gas supplier, call the fire department.
OPERATING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. Set the thermostat to lowest setting.
3. Turn off all electrical power to the appliance.
4. Remove jacket front panel.
5. This appliance is equipped with an ignition device which automatically lights the burner.
Do not try to light the burner by hand.
6. Turn Gas control knob clockwise
to OFF.
7. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If
you smell gas, STOP! Follow "B" in the safety information above. If you don't smell gas,
go to the next step.
8. Turn Gas control knob counterclockwise
9. Turn on all electric power to the appliance.
10. Set thermostat to desired setting.
to ON.
11. If the appliance will not operate, follow the instructions "TO TURN OFF GAS TO
APPLIANCE" below and call your service technician or gas supplier.
12. Replace jacket front panel.
TO TURN OFF GAS TO THE APPLIANCE
1. Set the thermostat to lowest setting.
2. Turn off all electric power to the appliance if service is to be performed.
3. Remove jacket front panel.
4. Turn Gas control knob clockwise
to OFF. Do not force.
5. Replace jacket front panel.
Part No.550-110-261/0999
13
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
Common problems and solutions
Symptom
Common Causes
Possible Corrections
Thermostat installed where drafts Locate thermostat on inner wall away from
Rapid cycling — boiler
or heat affect reading
heat sources or cool drafts.
turns on and off frequently
Heat anticipator in thermostat
adjusted incorrectly
Adjust thermostat per manufacturer’s
instructions.
Incorrect limit setting
Set limit according to system needs.
Maximum setting is 220˚F. Increase limit
setting to decrease cycling.
Insufficient water flow through
boiler
Check all valves to and from boiler. Return
to proper setting.
Confirm circulator size.
Expansion tank sized too small
Flooded expansion tank
Inoperative limit control
Call qualified service technician to check
expansion tank operation and size.
Frequent release of water
through relief valve
Call qualified service technician to check
expansion tank operation.
Call qualified service technician to replace
limit control.
Leaks in boiler or piping
Have qualified service technician repair
leaks at once to avoid constant use of
makeup water. Makeup water can cause
mineral deposits which, in turn, can cause
boiler section failure. Do not use petroleum-
base stop-leak compounds.
Need to frequently add
makeup water
Oxygen corrosion due to leaks in Have qualified service technician repair at
Black water condition
boiler and piping
once. Keep pH of water between 7.0 to 8.5.
14
Part No.550-110-261/0999
Download from Www.Somanuals.com. All Manuals Search And Download.
GOLD CGs — User’s Information Manual
Common problems and solutions
Symptom
Common Causes
Possible Corrections
Mineral deposits in sections due to Call qualified service technician to de-lime
Popping or percolating
noise heard in boiler
constant use of makeup water
boiler, if necessary. In some cases,
deposits will be too heavy to remove with
de-liming procedures.
Have qualified service technician repair
leaks to eliminate need for constant
makeup water.
Incorrect pH of boiler water
Call qualified service technician to check
pH level and correct. pH should be
maintained between 7.0 to 8.5.
Insufficient water flow through
boiler
Check all valves to and from boiler. Return
to proper setting.
Confirm circulator size.
Contaminated combustion air
supply — See page 4 in this
manual.
Remove any contaminating products. See
page 4 in this manual.
Metal flakes found in vent
outlet or vent — flueway
corrosion
Provide outside air for combustion. Kit
available through Weil-McLain distributor.
Have qualified service technician pipe-up
kit.
Condensation of combustion
gases in boiler sections
Have qualified service technician inspect
system piping and controls to verify proper
regulation of return water temperature.
Air in system
Bleed air from system through air vents in
radiators or baseboard units.
Some radiators or
baseboard units do not
heat or are noisy
Low system pressure
Fill to correct pressure.
Check for leaks in boiler or piping. Have
qualified service technician repair at once.
High limit set too low
Adjust high limit to higher setting.
Part No.550-110-261/0999
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Weil-McLain Limited Warranty for
Residential & Commercial Cast Iron Boilers
These warranties do not cover:
❏❏RESIDENTIALWATERWARRANTY—Limited Lifetime
❏❏RESIDENTIAL STEAMWARRANTY—Limited 10Year
❏❏COMMERCIAL WARRANTY—Limited 10-Year
1. Components that are part of the heating systems, but
were not furnished byWeil-McLain as a part of the boiler.
2. The workmanship of any installer ofWeil-McLain’s boilers.
In addition, this warranty does not assume any liability of
any nature for unsatisfactory performance caused by
improper installation.
NOTE: The residential steam and water warranties do not
cover residential boilers installed in buildings other than one or
two family dwelling units, unless they are buildings with individual
boilers for each dwelling unit.
3. Any costs for labor for removal and reinstallation of the
alleged defective part, transportation to Weil-McLain, if
necessary, and any other materials necessary to perform
the exchange.
FirstYear-(All Residential & Commercial Cast Iron
Boilers)
LimitedWarranty for Cast Iron Boilers:
Weil-McLain warrants that its cast iron boilers are free from
defects in material and workmanship for one year from the date
of installation. If any parts are found to be defective in manufacture,
Weil-McLain will provide replacement of such defective parts.
4. Improper burner adjustments, control settings,care or
maintenance. Information is included in the installation
Instructions, Owner’s Information Manual and/or Start-up,
Service and Maintenance Instructions, and other printed
technical material furnished byWeil-McLain with the boiler.
SecondThroughTenthYear-(ResidentialWater/Steam)
SecondThroughTenthYear-(CommercialWater/Steam)
LimitedWarranty for cast iron sections:
Weil-McLain warrants that the cast iron sections of its water and
steam boilers are free from defects in material and workmanship
from the date of installation for the second through the tenth year.
If, during such time period, any section is found to be defective,
Weil-McLain will provide replacement for the original cast iron
section(s).
5. Boilers operated with combustion air contaminated
externally by chemical vapors or with improper fuel
additives, or with water conditions which may have
caused unusual deposits in the cast iron sections.
These warranties extend only to the first retail purchaser of the boiler
and only to a boiler that has not been moved from its original installation
site.
EleventhYear and Beyond - (ResidentialWater Only)
Limited Warranty for Cast Iron Sections:
THE WARRANTIES DESCRIBED ABOVE ARE IN LIEU OF ALL
OTHERWARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITEDTO ANY IMPLIEDWARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE AND MERCHANTABILITY. WEIL-McLAIN
EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY FOR
CONSEQUENTIAL, INCIDENTAL, INDIRECT OR PUNITIVE
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY.
Weil-McLain warrants that the cast iron sections of its residential
water boilers are free from defects in material and workmanship
for the eleventh year and beyond from the date of installation.If,
during such time period, any section(s) is found to be defective,
Weil-McLain will provide replacement for the original cast iron
section(s) upon the payment of a proportionate charge based on
the time the boiler has been in service. The proportionate charge
will be equal to the appropriate percentage of the list price of
such section(s) at the time the warranty claim is made, and will
be determined as follows:
11th year - 5%; 12th year - 10%; 13th year - 15%;
14th year - 20%; 15th year - 25%; 16th year - 30%;
17th year - 35%; 18th year - 40%; 19th year - 45%;
20th year - 50%; 21st year - 55%; 22nd year - 60%;
23rd year - 65%; 24th year - 70%; 25th year and
beyond - 75%.
For prompt product warranty claims, notify the installer who, in turn, will
notify theWeil-McLain distributor from whom he purchased the boiler. If
this action does not result in warranty resolution, contact Weil-McLain
Consumer Relations Department, 500 Blaine Street, Michigan City,
Indiana 46360-2388, with details in support of the warranty claim. Alleged
defective part or parts must be returned through trade channels in
accordance with the Weil-McLain procedure currently in force for handling
returned goods for the purpose of inspection to determine cause of
failure. Weil-McLain will furnish new part(s) to an authorized Weil-McLain
distributor who, in turn will furnish the new part(s) to the heating contractor
who installed the boiler. If you have any questions about the coverage
of this warranty, contact Weil-McLain at the address above.
All Residential & Commercial Cast Iron Boilers
These warranties are subject to the condition that the boiler
must have been installed by a heating contractor whose principal
occupation is the sale and installation of plumbing, heating and/or
air conditioning equipment.
Weil-McLain
500 Blaine Street
Michigan City, IN 46360-2388
16
Part No.550-110-261/0999
Download from Www.Somanuals.com. All Manuals Search And Download.
|