¨
Model No. WEBE19300
Serial No.
USERÕS MANUAL
Write the serial number in the
space above for reference.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you have
questions, or if there are missing
parts, we will guarantee complete
satisfaction through direct assis-
tance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before
using this equipment. Save this
manual for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Precautions
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight rack.
1. Read all instructions in this manual before
using the weight rack. Use the weight rack
only as described in this manual.
12. Always secure your weights (not included)
with weight clips when they are mounted on
the barbell or the weight carriage.
2. It is the responsibility of the owner to ensure 13. Always lower the weight carriage in a con-
that all users of the weight rack are ade-
quately informed of all precautions.
trolled manner; never let the weight carriage
drop.
3. The weight rack is intended for home use
only. Do not use the weight rack in a com-
mercial, rental or institutional setting.
14. Always move your bench (not included) out
of the way when performing an exercise that
does not use the bench.
4. Use the weight rack only on a level surface.
Cover the floor beneath the weight rack for
protection.
15. Always remove the lat bar when performing
an exercise that does not require the use of
the lat bar.
5. Inspect and tighten all parts each time you
use the weight rack. Replace any worn parts
immediately.
16. If you feel pain or dizziness while exercising,
stop immediately and begin cooling down.
17. The decal shown below has been placed on
the weight rack. If the decal is missing or
illegible, please call our Customer Service
Department toll-free at 1-800-999-3756,
6. Keep children under 12 and pets away from
the weight rack at all times.
7. Keep hands and feet away from moving
parts.
Monday through Friday, 6 a.m. until 6 p.m.
Mountain Time, to order a free replacement
decal. Apply the decal in the location shown.
8. Always wear athletic shoes for foot protec-
tion while exercising.
WARNING
¥ Misuse of this
product may result in
serious injury.
9. Always make sure there is an equal amount
of weight (not included) on each side of the
barbell or the weight carriage.
¥ Read userÕs manual
and follow all war-
nings and operating
instructions prior to use
10. The weight rack is designed to support a
maximum of 300 pounds, including the bar-
bell and weights (weights are not included).
Do not place more than 300 pounds, includ-
ing the barbell, on the weight gliders and
safety spotters. Do not place more than 150
pounds on the weight carriage.
¥ Do not allow children
on or around machine.
¥ Replace label if
damaged, illegible, or
removed.
11. Always set both weight gliders and both
safety spotters at the same height.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Thank you for selecting the versatile WEIDER¨ XT55
PRO weight rack. The XT55 PRO is designed to help
you develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic
increase in muscle size and strength, or a healthier
cardiovascular system, the XT55 PRO will help you
achieve the specific results you want.
at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number is WEBE19300. The serial number can be
found on a decal attached to the weight rack (see the
front cover of this manual).
For your benefit, read this manual carefully before
Before reading further, please review the drawing
using the XT55 PRO. If you have additional questions, below and familiarize yourself with the parts that are
please call our Customer Service Department toll-free labeled.
High Pulley Station
Lat Bar
Lat Tower
Upright
Weight Guide
Left Side
Right Side
Weight Glider
Safety Spotter
Barbell
Weight Carriage
Low Pulley Station
Foot Plate
Note: The terms Òright sideÓ and Òleft sideÓ are
determined relative to a user standing with his
back toward the weight rack; they do not refer to
right and left on the drawings in this manual.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
R0800B
Part Identification ChartÑModel No. WEBE19300
Refer to the drawings below to identify small parts used in assembly. The number in parentheses below each
drawing is the key number of the part, from the Part List in the center of this manual. The number following the
key number is the quantity needed for assembly. Note: Some small parts may have been pre-attached. If a
part is not in the parts bag, check to see if it has been pre-attached.
M8 Nylon
Locknut (54)Ñ3
M10 Nylon
Locknut (11)Ñ38
M10 Small
Washer (6)Ñ14
M10 Large
Washer (58)Ñ6
M8 x 16mm Screw (50)Ñ2
M8 x 25mm Bolt (53)Ñ2
M8 x 70mm Bolt (30)Ñ1
M10 x 45mm Bolt (40)Ñ3
M10 x 20mm Bolt (26)Ñ2
M10 x 25mm Bolt (43)Ñ2
M10 x 30mm Bolt (38)Ñ2
M10 x 65mm Bolt (56)Ñ7
M10 x 75mm Bolt (39)Ñ2
M10 x 80mm Bolt (41)Ñ24
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Before beginning assembly, carefully read the
following information and instructions:
Some small parts may be pre-assembled.
¥ As you assemble the weight rack, make sure all
parts are oriented as shown in the drawings.
Make Things Easier for Yourself!
This manual is designed to ensure that the
weight rack can be assembled successfully by
anyone. By setting aside plenty of time, and by
deciding to make the task enjoyable, assembly
will go smoothly.
Assembly requires the following tools (not
included):
¥ Two adjustable wrenches
¥ One rubber mallet
¥ Assembly requires two people.
¥ One standard screwdriver
¥ One phillips screwdriver
¥ Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
¥ Lubricant, such as grease or petroleum jelly,
and soapy water.
¥ Tighten all parts as you assemble them, unless
instructed to do otherwise.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
¥ For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5. Note:
1. Before beginning, make sure you understand
the information in the box above. Note: Some
parts described in the assembly steps may be
pre-assembled.
1
41
55
57
Press a 60mm Square Inner Cap (55) into each end
of a Base (7). Attach the Base to the indicated end
of the Base Crossbar (20) using a Support Plate
(57), two M10 x 80mm Bolts (41), and two M10
Nylon Locknuts (11). Do not tighten the Nylon
Locknuts yet.
11
7
55
11
20
Attach the other Base (7) to the opposite side of the
Base Crossbar (20) in the same manner.
2. Press a 60mm Square Inner Cap (55) into the end
of the Rear Base (3). Attach the Rear Base and the
Foot Plate (4) to the Base Crossbar (20) using two
M10 x 80 mm Bolts (41) and two M10 Nylon
Locknuts (11). Do not tighten the Nylon Locknuts
yet.
2
11
55
3
11
20
4
41
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Attach an Upright (1) to each Base (7) using two
Joint Plates (12), four M10 x 80mm Bolts (41), and
four M10 Nylon Locknuts (11). Make sure the
Uprights are oriented exactly as shown. Do not
tighten the Nylon Locknuts yet.
3
1
41
7
1
12
7
12
11
12
12
41
4. Insert a Weight Guide (18) into the indicated hole in
each Base (7). Attach the Weight Guides to the
Bases using M10 x 75mm Bolts (39), M10 Small
Washers (6), and M10 Nylon Locknuts (11). Do not
tighten the Nylon Locknuts yet.
4
18
39
7
6
6
11
18
7
11
39
6
6
5. Press a 25mm Bushing (48) into each end of the
Locking Bar (34). Slide the Barbell (35) into the
Locking Bar (34).
5
48
34
35
48
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Press a 38mm Bushing (29) into each end of the
Right Weight Glider (31). Slide the Right Weight
Glider onto the indicated end of the Barbell (35)
and attach it to the Barbell using an M8 x 16mm
Screw (50). Do not tighten the Screw yet. Make
sure the Right Weight Glider is oriented exactly
as shown.
6
50
29
31
29
35
7. Press a 38mm Bushing (29) into each end of the
Left Weight Glider (32). Slide the Left Weight Glider
onto the indicated end of the Barbell (35) and
secure it to the Barbell using an M8 x 16mm Screw
(50). Do not tighten the Screw yet. Make sure
the Left Weight Glider is oriented exactly as
shown.
7
35
29
32
50
29
8. Press a 50mm Bushing (47) into the indicated end
of a Weight Adapter (33). Slide the Weight Adapter
onto the Barbell (35) and secure it to the Barbell
using a Large Washer (44) and an M10 x 25mm
Bolt (43).
8
35
Attach the other Weight Adapter (33) to the other
end of the Barbell (35) in the same manner.
33
47
Tighten the M8 x 16mm Screws (50) used in
steps 6 and 7.
44
43
9. Note: This step requires the help of a second
person.
9
34
Slide the Right Safety Spotter (23) and the Left
Safety Spotter (24) onto the Weight Guides (18).
Make sure the Safety Spotters are oriented
exactly as shown.
31
23
Slide the assembled Locking Bar (34) and the Right
and Left Weight Gliders (31, 32) onto the Weight
Guides (18). Make sure the Locking Bar and
Weight Gliders are oriented exactly as shown.
32
24
18
18
8
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Press a 60mm Square Inner Cap (55) into each end
of the Top Crossbar (9). Attach the Top Crossbar to
the Uprights (1) using four Joint Plates (12), eight
M10 x 80mm Bolts (41), and eight M10 Nylon
Locknuts (11). Do not tighten the Nylon Locknuts
yet.
10
38
6
55
9
38
6
Secure the Top Crossbar (9) to the Weight Guides
(18) using two M10 x 30mm Bolts (38) and two M10
Small Washers (6).
11
55
11
12
12
41
41
18
1
1
18
11. Press Carriage Bushings (27) into the ends of the
Weight Carriage (22). Press 50mm Round Inner
Caps (25) into the ends of the weight tube on the
Weight Carriage.
11
2
Angled End
27
25
Insert an M10 x 20mm Bolt (26) into the bracket on
the Weight Carriage (22).
Weight Tube
27
Slide the Weight Carriage (22) onto the Rear
Upright (2) as shown. Make sure that the Weight
Carriage and the Rear Upright are oriented as
shown.
22
25
26
12. Refer to the inset drawing. Press a Carriage
Bushing (27) into the top of the Carriage Stop (28)
as shown.
12
27
28
54
Slide the Carriage Stop (28) onto the lower end of
the Rear Upright (2). Attach the Carriage Stop to
the Rear Upright with an M8 x 70mm Bolt (30) and
an M10 Nylon Locknut (54).
11
28
6
30
2
30
Bracket
Slide the Rear Upright (2) onto the bracket on the
Rear Base (3). Attach the Rear Upright to the Rear
Base using two M10 x 65mm Bolts (56), four M10
Small Washers (6), and two M10 Nylon Locknuts
(11). Do not tighten the Nylon Locknuts yet.
6
3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Press a 50mm Square Inner Cap (10) into each end
of the Pulley Bar (59). Slide the bracket on the
Pulley Bar into the top of the Rear Upright (2).
Attach the Pulley Bar to the Rear Upright using two
M10 x 65mm Bolts (56), four M10 Small Washers
(6), and two M10 Nylon Locknuts (11).
13
10
59
11
41
10
Bracket
Attach the Pulley Bar (59) to the Top Crossbar (9)
using a Support Plate (57), two M10 x 80mm Bolts
(41), and two M10 Nylon Locknuts (11).
6
9
2
57
11
56
Tighten all Nylon Locknuts used in steps 1
through 13.
14. Identify the High Cable (13), which is the shorter of
the two Cables. Route the High Cable up through
the indicated slot in the Pulley Bar (59). Make sure
the ball is in the indicated location.
14
15
5
15
59
Route the High Cable (13) around a Pulley (5) as
shown. Attach the Pulley inside the slot in the
Pulley Bar (59) using an M10 x 65mm Bolt (56), two
M10 Large Washers (58), two Pulley Spacers (15),
and an M10 Nylon Locknut (11). Do not overtight-
en the Nylon Locknut. The Pulley must be able
to turn freely.
11
58
13
58
Ball
56
15. Route the High Cable (13) around another Pulley
(5) and through the indicated slot in the Pulley Bar
(59) as shown. Attach the Pulley inside the slot
using an M10 x 65mm Bolt (56), two M10 Large
Washers (58), two Pulley Spacers (15), and an M10
Nylon Locknut (11). Do not overtighten the Nylon
Locknut. The Pulley must be able to turn freely.
15
15
5
11
15
13
58
59
56
58
16. Route the High Cable (13) up through the Pulley
Bar (59) and around another Pulley (5) as shown.
Attach the Pulley inside the slot in the Pulley Bar
using an M10 x 65mm Bolt (56), two M10 Large
Washers (58), two Pulley Spacers (15), and an M10
Nylon Locknut (11). Do not overtighten the Nylon
Locknut. The Pulley must be able to turn freely.
16
15
5
15
11
58
13
56
59
58
10
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Slide the indicated end of the High Cable (13) onto
the M10 x 20mm Bolt (26) in the Weight Carriage
(22). Tighten an M10 Nylon Locknut (11) onto the
Bolt.
17
13
11
26
22
18. Route the High Cable (13) around a Pulley (5) as
shown. Hold a Cable Trap (21) against the Pulley
and attach a Pulley Plate (19) to each side of the
Pulley using an M10 x 45mm Bolt (40) and an M10
Nylon Locknut (11). Make sure the Cable Trap
holds the High Cable in the groove of the Pulley.
Do not overtighten the Nylon Locknut; the
Pulley must be able to turn freely.
18
13
5
21
11
40
19
19. Route the indicated end of the Low Cable (8)
around a Pulley (5). Attach the Pulley to the bracket
on the Base Crossbar (20) using an M10 x 45mm
Bolt (40) and an M10 Nylon Locknut. Do not over-
tighten the Nylon Locknut; the Pulley must be
able to turn freely.
19
5
8
11
40
20
20. Route the Low Cable (8) around a Pulley (5) as
shown. Hold a Cable Trap (21) against the Pulley
and attach the Pulley and Cable Trap to the lowest
holes in the two Pulley Plates (19) using an M10 x
45mm Bolt (40) and an M10 Nylon Locknut (11).
Make sure the Cable Trap holds the Low Cable in
the groove of the Pulley. Do not overtighten the
Nylon Locknut; the Pulley must be able to turn
freely.
20
19
11
40
21
5
8
11
Download from Www.Somanuals.com. All Manuals Search And Download.
21. Attach the indicated end of the Low Cable (8) to the
bracket on the Rear Base (3) using an M10 x 20mm
Bolt (26) and an M10 Nylon Locknut (11).
21
8
Bracket
3
11
26
22. Make sure all parts are properly tightened
before you use the weight rack. The use of all
remaining parts will be explained in Adjusting the
Weight Rack beginning below.
Adjusting the Weight Rack
This section explains how the weight rack can be adjusted. Inspect and tighten all parts each time you use the
weight rack. Replace any worn parts immediately. The weight rack can be cleaned with a damp cloth and a mild,
non-abrasive detergent. Do not use solvents.
USING THE WEIGHT ADAPTER
A Weight Adapter (42) and Pin (52) have been included
for use with the WEIDER¨ PRO XT15 weight bench
(model number WEBE0910).
Leg Lever
52
To use Olympic weights with the weight bench, slide the
Weight Adapter (42) onto the leg lever and secure it by
inserting the Pin (52) through the leg lever as shown.
42
USING THE LOCKING BAR
Before starting an exercise, position the barbell and the
Safety Spotters (23, 24) in the correct position for the
exercise.
1
1
To do this, stand in front of the rack and grip the
Locking Bar (34) with both hands. Turn the Locking Bar
until the two hooks disengage the slots in the Uprights
(1). Raise or lower the Locking Bar to a new position
and turn it until the hooks engage the slots in the
Uprights. Note: Always start an exercise with the
barbell positioned at the lowest point to which it
will move during the exercise.
31
23
Hook
Hook
32
34
24
Position both Safety Spotters (23, 24) directly under the
Weight Gliders (31, 32). (See USING THE SAFETY
SPOTTERS on page 13.)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SAFETY SPOTTERS
To move the Safety Spotters (23, 24 [not shown]) to a
new position, grip the handles on the spotter hooks and
pull the hooks out of the slots in the Uprights (1). Raise
or lower the Safety Spotters to new positions and pivot
the hooks back into the slots in the Uprights.
1
Hook
23
WARNING:
Always set both Safety
Spotters (23, 24) at the same height.
Handle
ATTACHING WEIGHTS TO THE BARBELL OR THE
WEIGHT CARRIAGE
Weights
To use the Barbell (35), slide the desired amount of
weight (not included) onto each end of the Barbell.
Secure the weights with Weight Clips (51).
35
51
Weights can be attached to the weight tube on the
Weight Carriage (22) in the same manner.
WARNING:
Do not place more than
300 pounds on the Barbell (35). Do not place
more than 150 pounds on the Weight Carriage
(22). Always place the same amount of weight on
each side of the Barbell or the Weight Carriage.
Always secure weights with Weight Clips (51).
22
ATTACHING THE LAT BAR TO THE HIGH PULLEY
STATION OR THE LOW PULLEY STATION
To use the high pulley station or the low pulley station,
attach the Lat Bar (16) to the High Cable (13) or the Low
Cable (not shown) using a Cable Clip (14).
13
14
16
WARNING:Always remove the Lat
Bar (16) when performing an exercise that does
not require the use of the Lat Bar.
TIGHTENING THE CABLES
Woven cable, the type of cable used on the weight rack,
can stretch slightly when it is first used. If the cables need
to be tightened, remove the M10 Nylon Locknut (11) and
the M10 x 45mm Bolt (40) from the lower ends of the
Pulley Plates (19). Reattach the Pulley (5) and Cable
Trap (21) to the next higher hole in the Pulley Plates.
Make sure the Cable Trap holds the Low Cable (8) in the
groove of the Pulley. Repeat until the cables are properly
tightened. Do not overtighten the Nylon Locknut. The
Pulley must be able to turn freely.
19
11
40
21
5
8
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Exercise Guidelines
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
Specifying the exact length of time for each workout,
and the number of repetitions and sets for each exer-
cise, is a highly individual matter. It is very important
to avoid overdoing it during the first few months of
your exercise program. You should progress at your
own pace and be sensitive to your bodyÕs signals. If
you experience pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
Find out what is wrong before continuing. Remember
that adequate rest and a proper diet are important
factors in any exercise program.
The only way to increase the size and strength of
your muscles is to push them to a high percentage of
their capacity. As you progressively increase the
intensity of your exercise, your muscles will continual-
ly adapt and grow. You can tailor each exercise to the
proper intensity level in two ways:
¥ by changing the amount of weight used
¥ by changing the number of repetitions or sets per-
formed (A ÒrepetitionÓ is one complete cycle of an
exercise, such as one sit-up. A ÒsetÓ is a series of
repetitions).
WARMING UP
The proper amount of weight for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of weight that is
right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repeti-
tions without difficulty, increase the amount of weight.
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
WORKING OUT
Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a mod-
erate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.
Each workout should include 6 to 10 different exercis-
es. Select exercises for every major muscle group
with emphasis on the areas that you want to develop
the most. To give balance and variety to your work-
outs, vary the exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
You will gain the greatest benefits from exercising by
maintaining proper form. This requires moving
through the full range of motion for each exercise and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted.
Cross Training
Many people desire a complete and balanced fitness
program. Cross training is an efficient way to accom-
plish this. One example of a balanced program is:
¥ Plan weight training workouts on Monday,
Wednesday, and Friday.
¥ Plan 20 to 30 minutes of aerobic exercise, such as
cycling or swimming, on Tuesday and Thursday.
¥ Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last only about half as long as
the return stage. Proper breathing is important.
Exhale during the exertion stage of each repetition
and inhale during the return stroke. Never hold your
breath.
The combination of weight training and aerobic exer-
cise will reshape and strengthen your body and devel-
op your heart and lungs.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure to rest for a short period of time after each
set. The ideal resting periods are:
¥ Rest three minutes after each set for a muscle build-
ing workout.
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is very effective for increasing flexibility.
¥ Rest one minute after each set for a toning workout.
¥ Rest 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
STAYING MOTIVATED
For motivation, keep a record of each workout. List
the date, the exercises performed, the weight lifted,
and the numbers of sets and repetitions completed.
Record your weight and key body measurements at
the end of every month.
COOLING DOWN
Remember, the key to achieving the greatest results
is to make exercise a regular and enjoyable part of
your everyday life.
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
MUSCLE CHART
N
O
P
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
A
B
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
C
D
E
Q
R
S
F
L
T
L. Rectus Abdominus (stomach)
M. Adductor (inner thigh)
G
M
N. Trapezius (upper back)
O. Rhomboideus (upper back)
P. Deltoid (shoulder)
H
I
U
V
Q. Triceps (back of arm)
J
K
W
R. Latissimus Dorsi (mid back)
S. Spinae Erectors (lower back)
T. Gluteus Medius (hip)
U. Gluteus Maximus (buttocks)
V. Hamstring (back of leg)
W. Gastrocnemius (back of calf)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Replacement Parts
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
¥ The MODEL NUMBER of the product (WEBE19300)
¥ The NAME of the product (WEIDER XT55 PRO weight rack)
¥ The SERIAL NUMBER of the product (see the front cover of this manual)
¥ The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING in the center of this manual).
Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which war-
ranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-autho-
rized by ICON. This warranty does not extend to any product or damage to a product caused by or attribut-
able to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-
ages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 167871 R0800B
Printed in China © 2000 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS PART LIST/EXPLODED DRAWING
FROM THE MANUAL
SAVE THIS PART LIST/EXPLODED DRAWING AND THE USERÕS MANUAL
FOR FUTURE REFERENCE
81
Download from Www.Somanuals.com. All Manuals Search And Download.
R0800B
Part ListÑModel No. WEBE19300
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
2
1
1
1
6
14
2
1
1
2
38
8
1
1
6
1
2
2
2
1
2
1
1
1
2
2
3
1
4
1
1
Upright
Rear Upright
Rear Base
Foot Plate
Pulley
M10 Small Washer
Base
Low Cable
Top Crossbar
50mm Square Inner Cap
M10 Nylon Locknut
Joint Plate
High Cable
Cable Clip
Pulley Spacer
Lat Bar
Plastic Handle
Weight Guide
Pulley Plate
Base Crossbar
Cable Trap
Weight Carriage
Right Safety Spotter
Left Safety Spotter
50mm Round Inner Cap
M10 x 20mm Bolt
Carriage Bushing
Carriage Stop
38mm Bushing
M8 x 70mm Bolt
Right Weight Glider
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
#
1
2
1
1
1
1
2
2
3
24
1
2
2
4
2
2
2
8
2
2
1
2
3
7
7
3
6
1
1
1
Left Weight Glider
Weight Adapter
Locking Bar
Barbell
Left Spotter Hook
Right Spotter Hook
M10 x 30mm Bolt
M10 x 75mm Bolt
M10 x 45mm Bolt
M10 x 80mm Bolt
Weight Adapter
M10 x 25mm Bolt
Large Washer
Weight Clip Bushing
Weight Adapter Bushing
50mm Bushing
25mm Bushing
45mm Square Bushing
M8 x 16mm Screw
Weight Clip
Pin
M8 x 25mm Bolt
M8 Nylon Locknut
60mm Square Inner Cap
M10 x 65mm Bolt
Support Plate
M10 Large Washer
Pulley Bar
UserÕs Manual
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
#
Exercise Guide
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the userÕs manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|