R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
TE475
TE475Y
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
WEED EATER
1030 Stevens Creek Road
Augusta, GA 30907
WEED EATER
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
545186833 Rev. 3 3/5/09 BRW
Download from Www.Somanuals.com. All Manuals Search And Download.
IDENTIFICATION OF SAFETY SYMBOLS
Store unit indoors in a high, dry place out of the reach of
children.
When servicing unit, use only identical replace-
ment parts.
Always stop unit and disconnect spark plug before
cleaning or servicing.
WARNING: Fire hazard. Never mix, pour, or store gasoline or
use the unit near a flame or sparks (including smoking, open flames, or
work that can cause sparks).
Use unleaded gasoline and two--stroke oil mixed at a ratio of
40:1 (2.5%).
SAFETY RULES
WARNING: When using gardening
appliances, basic safety precautions must al-
ways be followed to reduce the risk of fire and
serious injury. Read and follow all instructions.
DANGER:Never useblades or flailing
devices. This unit is designed for line trimmer
use only. Use of any other accessories or at-
tachments will increase the risk of injury.
If situations occur which are not covered in
this manual, use care and good judgment. If
youneed assistance, contact your authorized
service dealer or call 1-800-554--6723.
This power unit can be dangerous! Operator
is responsible for following instructions and
warnings on unit and in manual. Read entire
instruction manual before using unit! Be thor-
oughly familiar with the controls and the prop-
er use of the unit. Restrict the use of this unit
to persons who have read, understand, and
will follow the instructions and warnings on
the unit and in the manual. Never allow chil-
dren to operate this unit.
OPERATOR SAFETY
S Dress properly. Always wear safety glasses
or similar eye protection when operating, or
performing maintenance, on your unit (safety
glasses are available). Eye protection should
be marked Z87.
S Always wear face or dust mask if operation is
dusty.
S Always wear heavy, long pants, long sleeves,
boots, and gloves. Wearing safety leg guards
is recommended.
S Always wear foot protection. Do not go
barefoot or wear sandals. Stay clear of
spinning line.
INSTRUCTION
MANUAL
SAFETY INFORMATION
ON THE UNIT
3
Download from Www.Somanuals.com. All Manuals Search And Download.
S Secure hair above shoulder length. Secure or
remove loose clothing or clothing with loosely
hanging ties, straps, tassels, etc. They can
be caught in moving parts.
S Keep others including children, animals,
bystanders, and helpers at least 50 feet (15
meters) away. Bystanders should be encour-
aged to wear safety glasses. Stop engine
immediately if you are approached.
S Use only for trimming, scalping, mowing,
edging and sweeping. Do not use for prun-
ing or hedge trimming.
S Being fully covered also helps protect you
from debris and pieces of toxic plants thrown
by spinning line.
S Stay Alert. Do not operate this unit when you
are tired, ill, upset or under the influence of al-
cohol, drugs, or medication. Watch what you
are doing; use common sense.
S Keep firm footing and balance. Do not over-
reach.
S Keep all parts of your body away from muffler
and spinning line. Keep engine below waist
level. A hot muffler can cause serious burns.
S Cut from your right to your left. Cutting on left
side of the shield will throw debris away from
the operator.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
S Allow engine to cool; secure unit before stor-
ing or transporting in vehicle.
S Wear hearing protection.
S Never start or run inside a closed room or
building. Breathing exhaust fumes can kill.
S Keep handles free of oil and fuel.
UNIT / MAINTENANCE SAFETY
WARNING: Disconnect the spark
plug before performing maintenance except
carburetor adjustments.
S Look for and replace damaged or loose parts
before each use. Look for and repair fuel
leaks before use. Keep in good working
condition.
S Replace trimmer head parts that are chipped,
cracked, broken, or damaged in any other
way before using the unit.
S Maintain unit according to recommended pro-
cedures. Keep cutting line at proper length.
S Use only 0.080″ (2 mm) diameter WEED
EATER brand line. Never use wire, rope,
string, etc.
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbure-
tor by starting the engine and letting it run until
it stops.
S Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from wa-
ter heaters, electric motors or switches, fur-
naces, etc.
S Store unit so line limiter blade cannot acciden-
tally cause injury. The unit can be hung by the
shaft.
S Install required shield properly before using
the unit. Use only specified trimmer head;
make sure it is properly installed and securely
fastened.
S Store unit out of reach of children.
WARNING: The engine exhaust
from this product contains chemicals known
totheState of California to cause cancer, birth
defects or other reproductive harm.
S Make sure unit is assembled correctly as
shown in this manual.
S Make carburetor adjustments with lower end
supported to prevent line from contacting any
object.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or abnor-
mal swellings. Prolonged use in cold weather
has been linked to blood vessel damage in
otherwise healthy people. If symptoms occur
such as numbness, pain, loss of strength,
change in skin color or texture, or loss of feeling
in the fingers, hands, or joints, discontinue the
use of this tool and seek medical attention. An
anti--vibration system does not guarantee the
avoidance of these problems. Users who oper-
ate power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark ar-
resting screen which meets the requirements of
California Codes 4442 and 4443. All U.S. forest
land and the states of California, Idaho, Maine,
Minnesota, New Jersey, Oregon, and Washing-
ton require by law that many internal combus-
tion engines be equipped with a spark arresting
screen. If you operate in a locale where such
regulations exist, you are legally responsible for
maintaining the operating condition of these
parts. Failure to do so is a violation of the law.
S Keep others away when making carburetor
adjustments.
S Use only recommended WEED EATER ac-
cessories and replacement parts.
S Have all maintenance and service not ex-
plained in this manual performed by an autho-
rized service dealer.
FUEL SAFETY
S Mix and pour fuel outdoors.
S Keep away from sparks or flames.
S Use a container approved for fuel.
S Do not smoke or allow smoking near fuel or
the unit.
S Avoid spilling fuel or oil. Wipe up all fuel spills.
S Move at least 10 feet (3 meters) away from
fueling site before starting engine.
S Stop engine and allow to cool before remov-
ing fuel cap.
S Always store gasoline in a container ap-
proved for flammable liquids.
CUTTING SAFETY
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
For normal homeowner use, the muffler and
spark arresting screen will not require any ser-
vice.
After 50 hours of use, we recommend that your
muffler be serviced or replaced by your autho-
rized service dealer.
ASSEMBLY
ATTACHING SHIELD
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
WARNING: The shield must be prop-
erly installed. The shield provides partial protec-
tion from the risk of thrown objects to the opera-
tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
ADJUSTING THE ASSIST HANDLE
1. Loosen wing nut on handle.
2. Pivot the handle to a comfortable position;
retighten wing nut.
For proper orientation of shield, see KNOW
YOUR TRIMMER illustration in OPERATION
section.
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole in
bracket.
4. Securely tighten wing nut onto bolt.
Shield
Slot
PIVOT
Wing Nut
Bracket
Line Limiter
Blade
Groove
Wing
Nut
OPERATION
KNOW YOUR TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
ffler
Trimmer
Head
Line Limiter
Blade
Choke Lever
Starter Handle
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STOP SWITCH
CHOKE
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the RUN position.
The STOP switch is used to stop the engine. To
stop the engine, push and hold the switch in the
STOP position until the engine stops.
PRIMER BULB
The PRIMER BULB removes air from thecar-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
EDGE GUIDE
The EDGE GUIDE protects the unit fromcon-
tacting the ground during edging.
BEFORE STARTING ENGINE
HELPFUL TIP
WARNING: Be sure to read the fuel
information in the safety rules before you begin.
If you do not understand the safety rules, do not
attempt to fuel your unit. Call 1-800-554-6723.
If your engine switch reads
“push to stop”, it is always
in the ON position.
HOW TO STOP YOUR UNIT
S To stop the engine, push and hold the STOP
switch in the STOP position until the engine
stops.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
S If engine does not stop, move choke to the
FULL CHOKE position.
HELPFUL TIP
To obtain the correct oil mix
ratio, pour 3.2 ounces of
2-cycle synthetic oil into
one gallon of fresh gas.
HOW TO START YOUR UNIT
WARNING: The trimmer head will turn
while starting the engine. Avoid any contact with
the muffler. A hot muffler can cause serious
burns.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle
air-cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/WEED EATER brand
synthetic oil is recommended. Mix gasoline and
oil at a ratio of 40:1. A 40:1 ratio is obtained by
mixing 3.2 fluid ounces (95 ml) of oil with 1 gallon
(4 liters) of unleaded gasoline. DO NOT USE
automotive oil or marine oil. These oils will
cause engine damage. When mixing fuel, follow
instructions printed on container. Once oil is
added to gasoline, shake container momentarily
to assure that the fuel is thoroughly mixed.
Always read and follow the safety rules relating
to fuel before fueling your unit.
HELPFUL TIP
If your engine still does not
start after following these
instructions, please call
1 -800 -554-6723.
NOTE: Make sure approximately 3 - 4
inches (8 - 10 cm) of line is extended from
the cutting head before starting unit. This
will allow the line to advance properly
once the unit starts.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
CAUTION: Never use straight gasoline in
your unit. This will cause permanent engine
damage and void the limited warranty.
FUEL REQUIREMENTS
This engine requires the use of minimum 87
octane [R+M]/2 clean gasoline.
IMPORTANT
Use of alcohol blended fuels (called gasohol or
using ethanol or methanol) can cause major en-
gine performance and durability problems.
1. Set unit on a flat surface.
2. Slowly press the primer bulb 6 times.
3. Move choke lever to the FULL CHOKE
position.
WARNING: Alternative fuels (not gas-
oline) such as E--15 (15% alcohol), E--20 (20%
alcohol), E--85 (85% alcohol) are NOT classified
as gasoline and are NOT approved for use in
2--stroke gasoline engines. Use of alternative
fuels will cause problems such as: improper
clutch engagements, overheating, vapor lock,
power loss, lubrication deficiency, deterioration
of fuel lines, gaskets and internal carburetor
components, etc. Alternative fuels cause high
moisture absorption into the fuel/oil mixture
leading to oil and fuel separation.
4. Squeeze the throttle trigger fully and hold
through all remaining steps.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the RUN position; then, pull
the rope to clear the engine of excess fuel.
This could require pulling the starter handle
many times depending on how badly the unit
is flooded.
Prim
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
e
Lever
OPERATING POSITION
ALWAYS W
ion
Starter Handle
Long pan
5. Pull starter rope handle sharply until engine
sounds as if it is trying to start, but do not
pull rope more than 6 times.
6. As soon as engine sounds as if it is trying to
start, move choke lever to HALF CHOKE
position.
Heavy sho
7. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
NOTE: If the engine doesn’t start after 6
pulls (at the HALF CHOKE position),
move the choke lever to the FULL
CHOKE position and press the primer
bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the start-
er rope until the engine runs, but no more
than 6 pulls. If the engine still doesn’t
start, it is probably flooded. Proceed to
STARTING A FLOODED ENGINE.
8. Once the engine starts, allow it to run 10 se-
conds, then move the choke lever to the
RUN position. Allow the unit to run for 30
more seconds at RUN before releasing the
throttle trigger.
Cut from your right to your left.
WARNING: Always wear eyeprotec-
tion. Never lean over the trimmer head.
Rocks or debris canricochet or be throwninto
eyes and face and cause blindness or other
serious injury.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to “weld” onto the spool.
Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
To stop engine:
NOTE: If engine dies with the choke le-
ver in the RUN position, move the choke
lever to the HALF CHOKE position and
pull the rope until engine runs, but no
more than 6 pulls.
S Release the throttle trigger.
S Push and hold the STOP switch in the
STOP position until the engine stops.
TWIST AND EDGE
The Twist and Edge feature allows for easy
edging of sidewalks, patios, driveways, etc.
1. Pull the tab toward the engine.
2. Twist the shaft to the edging position; re-
lease tab.
STARTING A WARM ENGINE
1. Move the choke lever to the HALF CHOKE
position.
2. Squeeze and hold the throttle trigger. Keep
throttle trigger fully squeezed until the en-
gine runs smoothly.
3. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
4. Allow engine to run 15 seconds, then move
the choke lever to RUN.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If enginestill does not run, it
is probably flooded.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TRIMMER LINE ADVANCE
The cutting head advances line automati-
cally. Do not tap head on the ground to ad-
vance line. This may break parts and cause
cutting head to malfunction.
Tr
Upon unit start up, the line will advance auto-
matically to the correct cutting path length.
Always keep the shield in place when the tool
is being operated.
3 inc
abov
WARNING: Use only 0.080” (2 mm)
diameter round line. Other sizes and shapes
of line will not advance properly and will result in
improper cutting head function or can cause se-
rious injury. Do not use other materials such as
wire, string, rope, etc. Wire can break off during
cutting and become a dangerous missile that
can cause serious injury.
SCALPING -- The scalping technique re-
moves unwanted vegetation down to the
ground. Hold the bottom of the trimmer head
about 3 inches (8 cm) above the ground and
at an angle. Allow the tip of the lineto strikethe
ground around trees, posts, monuments, etc.
This technique increases line wear.
CUTTING METHODS
(8 cm)
ound
WARNING: Use minimum speed
and do not crowdthe linewhen cutting around
hard objects (rock, gravel, fence posts, etc.),
whichcan damage thetrimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
S The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
MOWING -- Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the
head into the ground as this can scalp the
ground and damage the tool.
Tip of the Line
Line Crowded Into
Work Area
Does The Cutting
M
Wrong
Right
S The line will easily remove grass and
weeds fromaround walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences. To
help avoid damage especially to delicate
vegetation or trees with tender bark,
shorten line to 4--5 inches (10--13 cm) and
use at less than full throttle.
SWEEPING -- The fanning action of the rotat-
ing line can be used for a quick and easy
clean up. Keep the line parallel to and above
the surfaces being swept and move the tool
from side to side.
S For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
S During light duty cutting.
S Near objects around which the line can
wrap such as small posts, trees or fence
wire.
Sweepin
S For mowing or sweeping, usefull throttle for
a good clean job.
TRIMMING -- Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
EDGING -- Adjust trimmer to the edging posi-
tion (see TWIST AND EDGE section). Allow
only the tip of the line to make contact. Do not
force trimmer line into work area.
Edging
MAINTENANCE
1. Clean the air filter cover and the area
around it to keep dirt from falling into the
carburetor chamber when the cover is
opened.
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
2. Open air filter cover by pushing button
(see illustration). Remove air filter.
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
HELPFUL TIP
IMPORTANT: Have all
repairs other than the rec-
ommended maintenance
3. Wash the filter in soap and water.
4. Allow filter to dry.
described in the instruction
manual performed by an
5. Replace air filter and close cover.
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, WEED EATER may not pay for
repairs under warranty. It is your re-
sponsibility to maintain and perform
general maintenance.
Button
Air Filter
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
Air Filter Cover
S Housing Screws
S Assist Handle Screws
S Debris Shield
MUFFLER AND SPARK ARREST-
ING SCREEN
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S STOP Switch -- Ensure STOP switch func-
tions properly by pushing and holding the
switch in the STOP position. Make sure en-
gine stops. Restart engine and continue.
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S Debris Shield -- Discontinue use of unit if
debris shield is damaged.
WARNING: The muffler on this prod-
uct contains chemicals known to the State of
California to cause cancer.
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen.
For normal homeowner use, however, the
muffler and spark arresting screen will not re-
quire any service. After 50 hours of use, we
recommend that your muffler be serviced or
replaced by your authorized service dealer.
INSPECT AND CLEAN UNIT AND
LABELS
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 inch (0.6 mm). Igni-
tion timing is fixed and nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and dis-
card.
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter-
gent.
S Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
(19 mm) socket wrench.
4. Reinstall the spark plug boot.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
LINE REPLACEMENT
INSTALLING SPOOL WITH LINE
1. Install replacement spool.
Pre--wound spools offer the most convenient
method for replacing line and ensuring opti-
mum performance.
2. Thread line through line guide ring.
Line through guide ring
Slot
S Replacement spools are color--coded to en-
sure use of the correct spool with your unit.
Be sure to use the same color spool as the
existing spool.
NOTE: Always clear dirt and debris from
cutting head components when performing
any type of maintenance.
S Hold spool and unscrew cap by turning in the
direction shown on top of the cap.
S Remove line guide ring and spool.
Replacement Spool
3. Rest guide ring on spool and place line
through slot. Allow line toextend 4 -- 6inch-
es (10 -- 15 cm) from center of spool.
4. Ensure line remains in slot while screwing
cap on to the shaft. Only tighten cap hand
tight!
NOTE: When removing and/or installing spool,
ensure dust cup remains installed over shaft.
CARBURETOR IDLE SPEED
ADJUSTMENT
WARNING: Keep others away when
making idle speed adjustments. The trimmer
head will be spinning during this procedure.
Wear your protective equipment and observe
all safety precautions.
The carburetor has been carefully set at the
factory. Adjustments may benecessary if you
notice any of the following conditions:
S Engine will not idle when the throttle is re-
leased.
Make adjustments with the unit supported so
the cutting attachment is off the ground and
will not make contact with any object. Hold
the unit by hand while running and making ad-
justments. Keep all parts of your body away
from the cutting attachment and muffler.
Use a pre--wound spool or refill spool with
line. If usinga pre--wound spool, remove tape
strip from line and spool.
REFILLING THE SPOOL WITH LINE
WARNING: Use only 0.080” (2 mm)
diameter round line. Other sizes and shapes
of line will not advance properly and will result in
improper cutting head function or can cause se-
rious injury. Do not use other materials such as
wire, string, rope, etc. Wire can break off during
cutting and become a dangerous missile that
can cause serious injury.
1. Cut a length of 25 feet of 0.080” (2 mm) di-
To adjust idle speed:
ameter round WEED EATER brand line.
Allow engine to idle. Adjust speed until engine
runs without stalling (idle speed too slow).
S Turn idle speed screw clockwise to in-
crease enginespeed if enginestalls or dies.
S Turn idle speed screw counterclockwise to
decrease engine speed.
Feed line in
direction
shown on
spool.
Idle Speed Screw
Spool
2. Insert one end of line into center cavity of
empty spool. Ensure line will feed into
spool in the direction shown on the spool
(counterclockwise).
3. Continue feeding line into spool, leaving 4 --
6 inches (10 -- 15 cm) unwound from center
of spool.
Air Filter Cover
If you require further assistanceor are unsure
about performing this procedure, contact an
authorized
service
dealer
or
call
1--800--554--6723.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
Follow the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
WARNING: Perform the following
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
HELPFUL TIP
During storage of your gas/
oil mixture, the oil will sepa-
rate from the gas.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
S Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy storage.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see messagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container.
We recommend that you
shake the gas can weekly
to insure proper blending of
the gas and oil.
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasolineto
oil ratio.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. Engine flooded.
1. See “Starting a Flooded Engine” in
Operation Section.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. Carburetor requires
adjustment.
5. Contact an authorized service dealer.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
1. See “Carburetor Idle Speed Adjustment”
in Service and Adjustments Section.
2. Crankshaft seals worn. 2. Contact an authorized service dealer.
3. Compression low.
3. Contact an authorized service dealer.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
Engine will not
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
1. Fuel mixture incorrect. 1. Empty fuel tank and refill with
correct fuel mixture.
smokes
excessively.
2. Air filter dirty.
3. Carburetor requires
adjustment.
2. Clean or replace air filter.
3. Contact an authorized service dealer.
1. Fuel mixture incorrect.
1. See “Fueling Engine” in Operation
section.
Engine runs
hot.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
WEED EATER,
a
division of Husqvarna
In Canada, contact:
Consumer Outdoor Products N.A., Inc.,
warrants to the original consumer purchaser
that each new WEED EATER brand gasoline
tool or attachment is free from defects in
material and workmanship and agrees to repair
or replace under this warranty any defective
gasoline product or attachment as follows from
the original date of purchase.
WEED EATER
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from
whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
30 DAYS - Parts and Labor, if used for rental
purposes.
WARRANTIES
EXCEPT
THOSE
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance or alteration,
or the use of accessories and/or attachments
not specifically recommended by WEED
EATER for this tool. This warranty does not
cover tune--up, spark plugs, filters, starter
ropes, cutting line, or rotating head parts that
will wear and require replacement with
reasonable use during the warranty period.
This warranty does not cover pre--delivery
setup or normal adjustments explained in the
instruction manual. This warranty does not
cover transportation costs.
EXPRESSLY STIPULATED HEREIN.S
OME STATES DO NOT ALLOWLIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY
LASTS OR THE EXCLUSION OR
LIMITATIONS
OF
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSION MAY
NOT APPLY TO YOU.
This is a limited warranty within the meaning of
that term as defined in the Magnuson--Moss Act
of 1975.
Thepolicy of WEED EATER is to continuously
improve its products. Therefore, WEED
EATER reserves the right to change, modify,
In the event you have a claim under this
warranty, you must return the product to an
authorized service dealer.
Should you have any unanswered questions
concerning this warranty, please contact:
WEED EATER, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.
1030 Stevens Creek Road
Augusta, GA 30907
1--800--554--6723
or
discontinue
models,
designs,
specifications, and accessories of all
products at any time without notice or
obligation to any purchaser.
U.S. EPA/CALIFORNIA/ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U.S. Environmental
Protection Agency, California Air Resources
Board, Environment Canada and WEED
EATER are pleased to explain the emissions
control system warranty on your year 2009 and
later small off--road engine. In California, all
small off--road engines must be designed, built,
andequippedto meet theState’s stringent anti--
smog standards. WEED EATER must war-
rant the emission control system on your
small off--road engine for the periods of time
listed below provided there has been no
abuse, neglect, or improper maintenance of
your small off--road engine. Your emission
control system includes parts such as the car-
buretor, the ignition system and the fuel tank.
Where a warrantable condition exists, WEED
EATER will repair your small off--road engine
at no cost to you. Expenses covered under
warranty include diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COV-
ERAGE: If any emissions related part on your
engine (as listed under Emissions Control
Warranty Parts List) is defective or a defect in
the materials or workmanship of the engine
causes the failure of such an emission related
part, the part will be repaired or replaced by
WEED EATER. OWNER’S WARRANTY RE-
SPONSIBILITIES: As the small off--road en-
gine owner, you are responsible for the per-
formance of the required maintenance listed
in your instruction manual. WEED EATER
recommends that you retain all receipts cov-
ering maintenance on your small off--road en-
gine, but WEED EATER cannot deny warran-
ty solely for the lack of receipts or for your
failuretoensure the performanceof allsched-
uled maintenance. As the small off--road en-
gine owner, you should be aware that WEED
EATER may deny you warranty coverage if
your small off--road engine or a part of it has
13
Download from Www.Somanuals.com. All Manuals Search And Download.
faileddue to abuse, neglect, improper mainte-
nance, unapproved modifications, or the use
of parts not made or approved by the original
equipment manufacturer. You are responsible
for presenting your small off--road engine to an
WEED EATER authorized repair center as
soon as a problem exists. Warranty repairs
should be completed in a reasonable amount of
time, not to exceed 30 days. If you have any
questions regarding your warranty rights and
responsibilities, you should contact your near-
est authorized service center, call WEED EAT-
ER at 1--800--554--6723, or send e-mailcorre-
spondence to emission.warranty@HCOP--
emission.com. WARRANTY COMMENCE-
MENT DATE: The warranty period begins on
the date the small off--road engine is pur-
chased. LENGTH OF COVERAGE: This
warranty shall be for a period of two years
from the initial date of purchase. WHAT IS
COVERED: REPAIR OR REPLACEMENT
OF PARTS. Repair or replacement of any
warranted part will be performed at no charge
to the owner at an approved WEED EATER
servicing center. If you have any questions
regarding your warranty rights and responsi-
bilities, you should contact your nearest au-
thorized service center, call WEED EATER at
1--800--554--6723, or send e-mail correspon-
warranted part is defective if the diagnostic
work is performed at an approved WEED
EATER servicing center. CONSEQUEN-
TIAL DAMAGES: WEED EATER may be li-
able for damages to other engine compo-
nents caused by the failure of a warranted
part still under warranty. WHAT IS NOT COV-
ERED: All failures caused by abuse, neglect,
or improper maintenance are not covered.
ADD -ON OR MODIFIED PARTS: The use
of add--on or modified parts can be grounds
for disallowing a warranty claim. WEED EAT-
ER is not liable to cover failures of warranted
parts caused by the use of add--on or modified
parts. HOW TO FILE A CLAIM: If you have any
questions regarding your warranty rights and re-
sponsibilities, you should contact your nearest
authorized service center, call WEED EATER
at 1--800--554--6723, or send e-mail corre-
spondence to emission.warranty@HCOP--
emission.com. WHERE TO GET WARRAN-
TY SERVICE: Warranty services or repairs
shall be provided at allWEED EATER service
centers. Call: 1--800--554--6723 or send
e-mail correspondence to emission.warranty
@HCOP--emission.com. MAINTENANCE,
REPLACEMENT AND REPAIR OF EMIS-
SION RELATED PARTS: Any WEED EAT-
ER approved replacement part used in the
performance of any warranty maintenance or
repair on emission related parts will be pro-
vided without charge to the owner if the part is
under warranty. EMISSION CONTROL
WARRANTY PARTS LIST: Carburetor, air fil-
ter (covered up to maintenance schedule), igni-
tion system: spark plug (covered up to mainte-
nance schedule), ignition module, muffler
including catalyst (if equipped), fuel tank.
MAINTENANCE STATEMENT:The owner is
responsible for the performance of all re-
quired maintenance as defined in the instruc-
tion manual.
dence
to
emission.warranty@HCOP--
emission.com. WARRANTY PERIOD: Any
warranted part which is not scheduled for re-
placement as required maintenance, or which
is scheduled only for regular inspection to the
effect of “repair or replaceas necessary” shall
be warranted for 2 years. Any warranted part
which is scheduled for replacement as re-
quiredmaintenance shall bewarranted for the
period of time up to the first scheduled re-
placement point for that part. DIAGNOSIS:
The owner shall not be charged for diagnostic
labor which leads to the determination that a
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|