SECT IONAL DOOR SYST EM
-
C 2400
C-2400
SECTIONAL DOOR SYSTEMS
STRONG,VISUALLY APPEALING DOORS FOR MODERATE
COMMERCIAL APPLICATIONS
The Wayne-Dalton C-2400 steel sectional door, available in a
variety of sizes, is an excellent value. Featuring nominal 24-gauge
ribbed steel sections, the C-2400 is available with a number of
lite and insulation options.
• NOMINAL 24-GAUGE STEEL
CONSTRUCTION
• STANDARD SIZES UP TO
20' 2" WIDE & 16' 1" HIGH
• VALUE PRICED CHOICE
• DESIGNED FOR MODERATE
COMMERICAL APPLICATIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD SIZES UP TO:
20' 2" WIDE & 16' 1" HIGH
CALL FOR ADDITIONAL SIZES
ENERGY EFFICIENCY VALUES:
U = 0.13
R = 7.60
WINDLOAD:
MEET OR EXCEED
ANSI/DASMA 102-2003
IN ACCORDANCE WITH
ASTM E-330-70.
BEST APPLICATIONS:
- Economy
- Windload performance
General Operating Clearances
Headroom***
2" track 3" track 2" track 3" track
121⁄2-17"
NA
141⁄2-20" 151⁄2-21"
Sideroom**
Depth Into Room
2" & 3" track
Center Line of Springs
Type
2" track
3" track
Standard Lift Manual12"R
Opening Height +12"
NA
Opening Height +18"
Opening Height +66"
Opening Height – Lift +30"
Opening Height +18"
Standard Lift Manual15"R
Opening Height +13" Opening Height +14"
Opening Height +12" NA
Opening Height +13" Opening Height +14"
Opening Height
+Lift +61⁄2
Standard Lift Motor Oper. 12"R 15-191⁄2
Standard Lift Motor Oper. 15"R 15-191⁄2
"
"
NA
18-231⁄2
41⁄2
"
51⁄2
"
"
Opening Height
+Lift +71⁄2
High Lift Manual
Door Height
+12"
"
"
High Lift Motor Oper.
Vertical Lift Manual 12"R
Vertical Lift Motor Oper. 12"R
Low Headroom Manual*
24" One Side
Door Height
+20"
41⁄2
"
51⁄2
"
Double Door Height
+13"
24" One Side
6-141⁄2
"
6-141⁄2
81⁄2-17"
"
Opening Height +20" - 26"
Opening Height +66"
Does Not Apply
6" 9"
Low Headroom Motor Oper.* 81⁄2-17"
*Note: Rear mount torsion requirements shown on chart. See
drawings for front mount torsion clearances.
Panel/Section Selection Guide
**Note: 8” sideroom required, one sidefor doors having chain
hoist. 24" side room required, one side for doors having
jackshaft operators.
***Note: Clear headroom is based on cable size so please contact
factory for specific headroom for your door.
Door Section and Lite Selection
Door Height and Section Selection
Door Width No. Panels Max. No.Windows Door Height
No. Sections
Up to 9'2"
9'3" to 12'2"
12'3" to 16'2"
16'3" to 19'2"
19'3" to 20'2"
2
3
4
5
6
2
3
4
5
7
Up thru 8'1"
8'2" thru 10'1"
10'2" thru 12'1"
12'2" thru 14'1"
14'2" thru 16'1"
4
5
6
7
8
For Larger Sizes – See Model C-24
Track Selection Guide
Standard Lift
High Lift
Roof Pitch
(standard or high lift)
Vertical Lift
Low Headroom
(rear mount torsion) (front mount torsion)
Low Headroom
(break-away is
standard, straight
incline is available)
www.wayne-dalton.com/commercial
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTIONAL DOOR SYSTEMS
C-2400
Note to specifiers: Words in parentheses indicate frequently specified and highly recommended options.
PART I – GENERAL
1.08 Warranty
2.04 Locks
1.01 Section Includes
A. Standard manufacturer’sTENYEAR warranty
against cracking,splitting or deterioration due to
rust-through.
A. Locks shall engage the right-hand vertical track
A. Sectional overhead doors [manually] [motor] operated
with accessories and components.
and utilize [an interior side lock] [standard size
rim cylinder].
1.02 Related Work
PART I I – PRODUCTS
2.05 Weatherstripping
A. Opening preparation,miscellaneous or structural
steel work,access panels finish or field painting are in
the scope of work of other trades and divisions of
these specifications.
2.01 Manufacturer
A. Doors shall be equipped with vinyl bulb shaped astragal
as standard on the bottom section.Optional joint,top
head,and jamb seals are available.
A. Wayne-Dalton or approved equal Model C-2400
insulated sectional overhead doors of steel
construction complete as specified in this section and
as manufactured by Wayne-Dalton Corp.
2.06 Glazing
1.03 Reference Standards
A. Optional.
A. ANSI/DASMA 102 –American National
Standards Institute [A216.1] Specifications for
sectional overhead doors published by Door &
Access Systems ManufacturersAssociation
International in bulletin 102-1990.
2.02 Materials
A. Door Sections:Shall be of roll formed steel type with
box shaped 20 ga.[intermediate and end stile
construction] and calculated materials“R”- value of
7.60 [optional] in accordance with industry guidelines.
1. Exterior Skin:Structural quality,hot-dipped
galvanized steel, with [embossed stucco] [smooth]
finish nominal 24 ga.with baked-on polyester
primer and [white] [brown] polyester finish coats
with [smooth][non-repeating random stucco
texture] and 4 deep pinstripes.
2.07 Windload
A. Windload – per DASMA 102-2003 and as required by
local codes.
B. ASTM A123 – Zinc [hot-dipped galvanized]
coatings on iron and steel products.
PART III – EXECUTION
3.01 Installation
C. ASTM A216 – Specifications for sectional
overhead type doors.
A. General:
1. Install doors in accordance with manufacturer’s
instructions and standards.Installation shall be by an
authorizedWayne-Dalton representative.
2. Verify that existing conditions are ready to receive
sectional overhead door work.
D. ASTM A229 – Steel wire,oil-tempered for
mechanical springs.
E. ASTM A-653-94 – Steel sheet,zinc-coated
[galvanized] by the hot-dipped process,
commercial quality.
2. Insulation:Cavity shall be filled with laid-in-place
[polyurethane] [expanded polystyrene] and
covered with [vinyl] [ 0.015” minimum embossed
steel] held in place with polymer clips.
3. Beginning of sectional overhead door work means
acceptance of existing conditions.
F. ASTM E330 – Structural performance of
exterior windows,curtain walls,and doors by
uniform static air pressure difference.
G. ASTM E413-87 – Sound transmission class.
Acoustical performance value = 23 per.J.
H. ASTM E1332-90 – Outdoor-indoor
transmission class.
B. Track:Track design shall be [standard lift] [high lift]
[vertical lift] [low headroom].Vertical mounting angles
shall be hot-dipped galvanized.Track size shall be [2"]
[3"].Vertical track shall be graduated to provide wedge
type weathertight closing with continuous angle
mounting for [steel] [wood] jambs,and shall be fully
adjustable to seal door at jambs [bracket mount for
wood].Horizontal track shall be reinforced with
continuous angle of adequate length and gauge to
minimize deflection.
B. Install door complete with necessary hardware,jamb
and head mold strips,anchors,inserts,hangers,and
equipment supports in accordance with final shop
drawings,manufacturer’s instructions,and as specified
herein.
C. Fit,align and adjust sectional overhead door assemblies
level and plumb for smooth operation.
D. Upon completion of final installation,lubricate,test and
adjust doors to operate easily,free from warp,twist or
distortion and fitting for entire perimeter.
Note: Architect may consider providing a schedule when
more than one sectional overhead door or opening
type is required.
Acoustical performance value = 19.
1.04 Quality Assurance
A. Sectional overhead doors and all accessories and
components required for complete and secure
installations shall be manufactured as a system from
one manufacturer.
Note: Horizontal track applies to standard lift,high lift,low
headroom and follow-the-roof designs only.
C. Hardware:Hinge and RollerAssembly:
1. Hinges and brackets shall be made from hot-
dipped,galvanized steel.
1.05 Systems Description
3.02 Materials (See note above.)
A. Sectional Overhead Door:Type:
2. Track rollers shall be case-hardened inner
steel races with 10-ball [2"] [3"] rollers.
Model C-2400
B. Mounting:Continuous angle mounting for [steel]
[wood] jambs [bracket mounting for wood jambs]
C. Operation:[manual push-up] [chain hoist] [motor]
[motor with chain hoist]
3. All factory authorized attachments shall be
made at locations indicated.
D. Counterbalance:
1. Springs shall be torsion type,low-stress,helical
wound,oil-tempered spring wire to provide
minimum [10,000 standard] [25,000] [50,000]
[100,000] cycles of use,on continuous steel [solid].
2. Spring fittings and drums made of die cast,high
strength aluminum.
D. Material:Galvanized steel with polyester finish paint
E. Insulation:Optional [polystyrene] [polyurethane]
1.06 Submittals
A. Shop Drawings:Clearly indicate the following:
1. Design and installation details to withstand
standard windload.
3. Pre-formed galvanized steel aircraft cable shall
provide a minimum of a 5:1 safety factor.
2. All details required for complete operation
and installation.
3. Hardware locations.
4. Type of metal and finish for door sections.
5. Finish for miscellaneous components and
accessories.
2.03 Operation
A. Operation shall be [manual push-up] [chain hoist]
[motor] [motor with chain hoist].
Note: Manufacturer does not recommend chain hoists or
jack shaft operators on the following track applications.
• 15" radius standard lift with roof pitch
less than 2:12
B. Product Data:Indicating manufacturer’s product
data,and installation instructions.
• Hi-lift less than 24"
1.07 Delivery, Handling, Storage
A. Deliver products in manufacturer’s original
containers,dry,undamaged,seals and labels intact.
B. Store and protect products in accordance with
manufacturer’s recommendations.
• Hi-lift between 12" – 23" with roof pitch
less than 1:12
• Low headroom track
Special chain hoist assemblies (using a trolley rail)
are available for the above track systems.
®
Distributed By:
For technical information, visit:
Printed in U.S.A.
Item #332545 Revised 9/2007
www.wayne-dalton.com/commercial
© 2007 Wayne-Dalton Corp. • One Door Drive • Mt. Hope, Ohio 44660 • 800-764-1457
Download from Www.Somanuals.com. All Manuals Search And Download.
Mt. Hope, OH • Dalton, OH • Trail, OH • Pensacola, FL • Portland, OR
|