Keyed-in-Handle Secure ECR Lock
Installation Instructions
and Owner’s Manual
Wayne-Dalton Corp.
P.O. Box 67 Mt. Hope, OH 44660
Models: 260597, 260600
All Residential Door Models: 8000/9000 Series & Wood Doors
PHILLIPS HEAD MACHINE SCREWS
(2) 1” (9200) #306564
(2) FOAM TAPE
(9200/9600/9900)
3/4” X 2-1/2”
(2) 1-1/4” (9600/8300 & WOOD)#306565
(2) 1-1/2” (9900) #306566
(6) 1/4-20 X 9/16”
TRACK BOLTS
#200527
#306653
(2) 1-3/4” (8000/PR9000/8500) #306567
UNIVERSAL
LOCK STILE
OUTSIDE
(9200/9600 & 9900)
#261964
HANDLE
#255543
(2) RETURN SPRING
#130023
(6) 1/4-20 X 11/16”
SELF DRILLING
SCREWS #300723
(6) 1/4” -20
LOCK BACKUP PLATE
(8300/8500 & WOOD)
#128564
FLANGED HEX NUTS
#100279
OR
1/4-14 X 1”
LAG SCREWS
(WOOD DOORS
ONLY) #107584
RIGHT LOCK BAR
#130024
INSIDE DOOR HANDLE
#307893
(2) #8 - 32 X 3/4”
(2) SECURE LOCK BASE II
#245957
PHILLIPS HEAD SELF TAPPING
SCREWS #100278
LOCK CABLE
#307894
(2)STRIKER
PLATES #130025
LEFT LOCK BAR
#150987
Required Tools
(1) Electric Drill
(1) 1/8” Drill Bit
(1) 3/4” Dia. Hole Saw
(1) 7/16” 6 Point Nut Driver
(1) 7/16” Wrench Or Socket
(1) Pliers/Wire Cutter
(1) Phillips Screw Driver
(1) Standard Screw Driver
(1) Center Punch
Important Notice!
REFER TO THE DOOR MODEL INSTALLATION INSTRUCTIONS MANUAL FOR
© Copyright 2007 Wayne-Dalton Corp.
Rev1 07/05/2007
Part No: 307896
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Outside Lock Handle Assembly
3/4” DIA.
HOLES
8000/PR9000 & PR9050 Series doors (see Fig. 4),
align the outside handle assembly with the handle point-
ing towards the floor and insert the assembly through
the previously drilled 3/4” diameter holes in the section.
Secure the outside lock handle to the section with (2)
#10 phillips head screws.
OUTSIDE
HANDLE
HANDLE
SHANK
9000 Series & Wood doors (see Fig. 5), align the out-
side handle assembly with the handle pointing towards
the floor and insert the assembly through the previously
drilled 3/4” diameter holes in the section. With the
outside lock placed in the section, place the center lock
stile over the shank of the outside lock handle, secure
the center lock stile with foam tape (8300/8500 Series
& Wood doors will use the lock backup plate with no
foam tape). Secure the outside lock handle to the sec-
tion by placing the (2) #10 phillips head machine screws
through the lock stile into the lock section. NOTE:
Before proceeding to the next step its recommended
that the outside handle be locked.
#10 PHILLIPS
Fig. 4
HEAD SCREWS
HANDLE
SHANK
FOAM TAPE
OUTSIDE
HANDLE
CENTER
STILE
3/4” DIA.
HOLES
#10 PHILLIPS
HEAD SCREWS
Fig. 5
Step 3: Inside Handle Assembly
8000/8100/8200 & 9000 Series doors (see Fig.6), po-
sition the inside handle over the shank of the outside
handle, flush against the center stile. Align the holes
in the handle with the pre-punched holes in the center
stile, then turn the handle clockwise to secure with (2)
#8 screws.
PRE-PUNCHED
HOLES
HANDLE
SHANK
8300/8500 Series & Wood doors ( see Fig.7), position
the inside handle over the shank of the outside handle,
flush against the lock backup plate. Align the holes
in the handle with the pre-punched holes in the lock
backup plate, then turn the handle clockwise to secure
with (2) #8 screws.
INSIDE
HANDLE
CENTER
STILE
(2) #8 SCREWS
Fig. 6
BACKUP PLATE
PRE-PUNCHED
HOLES
NOTE: When securing the inside handle bracket,
be sure not to over tighten the screws or damage to
the inside handle may occur.
NOTE: Follow the Main Installation Instruction
Manual to install the door sections and vertical track
before you install the remainder of the lock parts.
After the sections and track are installed, continue
with Step 4.
SHANK
HANDLE
(2) #8 SCREWS
INSIDE
HANDLE
Fig. 7
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4: Installing the Secure Lock
1
8000/9000 Series & Wood doors (Fig.1-3), locate the
inside handle and uncoil the lock cable, then thread the
cable through the inside handle as illustrated (see Fig.1).
3
Locate the secure lock striker plates over the pre-punched
holes in the vertical track nearest the center of the lock
section (see Fig.2). Fasten the striker plates to the vertical
track using (2) 1/4-20 x 9/16” track bolts and flanged hex
nuts. Lock bars are embossed “R” for right side and “L”
for left side. Place the lock bars into the slots in the secure
lock base (see Fig. 3).Attach the springs to the tabs on the
base and the lock bar. Position the end of the right lock bar
into the slot in the right striker plate. Move the base of the
secure lock back 1/8” from the edge of the section. Attach
the secure lock to the section with (4) 1/4-20 x
2
4
11/16” self drilling screws. Repeat for the left side. Feed
one end of the lock cable through the slotted hole of a
lock bar and secure with (1) 1/4-20 x 9/16” track bolt. Pull
the cable taut, but not enough to pull the lock bar out of
the striker plate. While holding taut, feed the lock cable
through the slotted hole of the remaining lock bar, secure with (1) 1/4-20 x 9/16” track bolt and flanged hex nut.
NOTE: Ensure that the bolt is through the front of the lock bar and the nut is on the back of the lock bar
with cable going through the front of the lock bar.
Operate the lock several times to make sure the lock bars clear the striker plates when the handle is turned and the
lock bars engage the striker plates when the handle is released. Adjust the cables if necessary. Trim off the excess
cable with wire cutters after the lock is operating satisfactorily.
1/8” OFFSET FROM
EDGE OF DOOR
1/4-20 FLANGED
HEX NUT
RIGHT HAND
LOCK BAR
1/4-20 X 11/16”
SELF DRILL SCREWS
1/4-20 X 9/16”
TRACK BOLTS
LOCK CABLE
SECURE LOCK
BASE II
HOOK SPRING OVER
TABS ON LOCK BAR
INSIDE
ALIGN LOCK BAR
INTO FRONT SLOT
AND BASE
VERTICAL
TRACK
HANDLE
9900 SERIES DOORS
USE BACK SLOT
STRIKER
PLATE
SLIDE LOCK BAR
THROUGH THE
FRONT SLOT
LOCK BARS ARE
EMBOSSED FOR
IDENTIFICATION
LEFT HAND
LOCK BAR
Fig. 3
Fig. 2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|