INSTALLATION &
OPERATION MANUAL
GS, GL & GT SERIES
FULLY STEAM JACKETED GAS KETTLES
MODEL
GS25E
GS30E
GL40E
GS60E
GL80E
GT100E
GT125E
GT150E
ML-52633
ML-52634
ML-52635
ML-52660
ML-52637
ML-52638
ML-52639
ML-52640
GL Series Kettle
VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791
FORM 30960 Rev. B (Oct. 2003)
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation Codes and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Testing the Gas Supply System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Flue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Faucet Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Before First Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Controls — Kettles With Electronic Ignition (Current Construction) . . . . . . . . . . . . . . . 7
Controls — Kettles With Electronic Ignition (Prior Construction) . . . . . . . . . . . . . . . . . 8
Controls — Kettles With Manual Pilot Light (Prior Construction) . . . . . . . . . . . . . . . . . 8
Kettle Features — Common To All Constructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Food Draw-Off Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Turning On a Kettle Equipped With Electronic Ignition . . . . . . . . . . . . . . . . . . . . . . . . 10
Turning On a Kettle Equipped With a Manual Pilot Burner . . . . . . . . . . . . . . . . . . . . . 10
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Daily — Kettle Food Draw-Off Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Pressure Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Low Water Cut-Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Jacket Water & Jacket Water Treatment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Hood Ventiliation System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Service and Parts Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
– 3 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, Operation and Care of
GS, GL & GT SERIES
FULLY STEAM JACKETED GAS KETTLES
KEEP THESE INSTRUCTIONS FOR FUTURE USE
GENERAL
Your Vulcan steam jacketed kettle is produced with quality workmanship and material. Proper
installation, usage and maintenance will result in many years of satisfactory performance.
Vulcan-Hart Company suggests that you thoroughly read this entire manual and carefully follow
all of the instructions provided.
INSTALLATION
Prior to installation check the electrical service and type of gas supply (natural or propane) to
make sure they agree with the specifications on the machine data plate located on the lower-left
inside front cover.
UNPACKING
This kettle was inspected before leaving the factory. The transportation company assumes full
responsibility for safe delivery upon acceptance of the shipment. Immediately after unpacking,
check for possible shipping damage. If the kettle is found to be damaged, save the packaging
material and contact the carrier within 15 days of delivery.
LOCATION
Position the kettle in its final location. Check that there are sufficient clearances for operating
and servicing the kettle, and for proper clearance of the cover when raised. Keep the kettle free
and clear from all combustible substances. Minimum clearance from combustible and non-
combustible construction is 2" (5.0 cm) at the rear and 6" (15.2 cm) at each side.
The kettle draw off valve should be located near a floor drain.
Do not obstruct the flow of air into and around the kettle. This air flow is necessary for proper
combustion of gases and for ventilation of the kettle. Provisions for ventilation and incoming air
supply for the equipment in the room must be in accordance with the National Fuel Gas Code
ANSI Z223.1 (latest edition).
LEVELING
Place a spirit level on the rim of the kettle with the cover open. Turn the feet in or out to level the
kettle in both the left-to-right and front-to-rear directions.
– 4 –
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION CODES AND STANDARDS
In the United States, Vulcan kettles must be installed in accordance with state and local codes, with
the National Fuel Gas Code, (ANSI-Z223.1, latest edition) available from the American Gas Association,
1515 Wilson Boulevard, Arlington, VA 22209, with the National Electrical Code (ANSI/NFPA No. 70,
latest edition) available from the National Fire Protection Association, Batterymarch Park, Quincy, MA
02269 and with Vapor Removal from Cooking Equipment, (NFPA-96, latest edition) available from
NFPA.
In Canada, the kettle must be installed in accordance with local codes, with the National Fuel Gas Code
(CAN/CGA-B149.1, latest edition) available from the Canadian Gas Association, 178 Rexdale
Boulevard, Etobicoke, Ontario, Canada M9W 1R3, and with the Canadian Electrical Code (CSA C22.2
No.3, latest edition) available from the Canadian Standards Association, 178 Rexdale Boulevard,
Etobicoke, Ontario, Canada M9W 1R3.
GAS CONNECTION
The gas supply connection and any pipe joint compound must be resistant to the action of
propane gases.
Codes require that a gas shutoff valve be installed in the gas line ahead of the kettle.
Connect the gas supply line to the gas valve on the kettle. Make sure the pipes are clean and
free of obstructions, dirt and piping compound.
The gas line must be capable of delivering gas to the kettle without excessive pressure drop at
the rate specified on the nameplate. Suggested gas supply line pressure is 7" Water Column
(1.75 kPa) for natural gas and 11" Water Column (2.75 kPa) for propane. Burner manifold pressure
is 3.5" Water Column (0.875 kPa) for natural gas and 10" Water Column (2.5 kPa) for propane.
WARNING: PRIOR TO LIGHTING, CHECK ALL JOINTS IN THE GAS SUPPLY LINE FOR
LEAKS. USE SOAP AND WATER SOLUTION. DO NOT USE AN OPEN FLAME.
After piping has been checked for leaks, all piping receiving gas should be fully purged to remove
air.
TESTING THE GAS SUPPLY SYSTEM
1
When test pressures exceed ⁄2 psig (3.45 kPa), the kettle and its individual shutoff valve must
be disconnected from the gas supply piping system.
When test pressures are 1⁄2 psig (3.45 kPa) or less, the kettle must be isolated from the gas supply
system by closing its individual manual shutoff valve.
FLUE
DO NOT obstruct the flow of flue gases from the flue located on the rear of the kettle. It is
recommended that the flue gases be ventilated to the outside of the building through a ventilation
system installed by qualified personnel. The flue on the kettle should not be directly connected
to any ventilation system. From the termination of the flue to the filters of the hood venting
system, a minimum clearance of 18" (116 cm) must be maintained.
Information on the construction and installation of ventilating hoods may be obtained from Vapor
Removal from Cooking Equipment, NFPA-96 (latest edition), available from the National Fire
Protection Association, Batterymarch Park, Quincy, MA 02269.
– 5 –
Download from Www.Somanuals.com. All Manuals Search And Download.
FAUCET BRACKET
A bracket is provided for mounting a faucet on the kettle; this would allow the addition of water
to the kettle for the convenience of the food preparer. A faucet is available as an accessory.
NOTE: Do not use tap water from faucet to fill kettle jacket. Refer to Jacket Water & Jacket Water
Treatment on page 12.
ELECTRICAL CONNECTION
WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE
APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL
ELECTRICAL CODES.
WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW
LOCKOUT / TAGOUT PROCEDURE.
All kettles are connected to 120 volt, 60 Hz. supply through the pigtail leads in the supply junction
box located inside the control panel.
Remove the control box cover. Connect electrical supply to the terminal block per the wiring
diagram located inside the control box cover. Use copper wire suitable for at least 75°C. Connect
a ground wire to the ground lug in the junction box. NOTE: Earth ground is required for proper
operation of electonic ignition. Replace the control box cover.
BEFORE FIRST USE
Use a non-corrosive, grease-dissolving commercial cleaner to clean the protective metal oils
from all surface parts and the interior of the kettle. Follow the cleaner manufacturer's directions.
Rinse thoroughly with warm water to remove all traces of the cleaner. Drain the kettle's interior
cooking area. Wipe dry with a clean cloth.
– 6 –
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING: THE KETTLE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING,
CLEANING AND SERVICING THE KETTLE.
Before operating, check the jacket water level by looking at the sight glass at the rear of the kettle
with both upper and lower valves open. The water level should be at the midpoint of the sight
glass. If water is below the recommended level or if it is murky, refer to Jacket Water Level,
page 12. Also check the flue at the rear of the kettle for any obstructions before operating.
CONTROLS — KETTLES WITH ELECTRONIC IGNITION (Current Construction, Fig. 1)
LID
KETTLE
JACKET
THERMOSTAT
OFF
PRESSURE GAUGE
ON – OFF SWITCH
OFF
ON
MAIN BURNER INDICATOR LIGHT
PILOT BURNER INDICATOR LIGHT
Pilot
Main
Burner Burner
JACKET WATER LEVEL
COMBINATION CONTROL VALVE
(Kettles built after September 2003)
Fig. 1
Thermostat
— Controls heat in the kettle. High dial settings are for cooking; low
settings are for holding.
Pressure Gauge
On – Off Switch
— Indicates pressure in the jacket, normal operating range is 0 to
12 psig.
— Located below pressure gauge, when turned to ON, initiates
electronic ignition to start the Pilot and Main Burner.
Pilot Burner Indicator Light — When lit, the electronic ignition system is attempting to light the
Pilot or the Pilot has been lit; it remains lit when the Main Burner
is on.
Main Burner Indicator Light — When lit, the Main Burner is providing heat to the kettle.
Combination Control Valve — Located inside box, this valve controls gas flow to the Main Burner.
– 7 –
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS — KETTLES WITH ELECTRONIC IGNITION (Prior Construction, Fig. 2)
Thermostat
— Controls heat in the kettle. High dial settings are for cooking; low
settings are for holding.
On – Off Switch
— Located on the upper right-hand corner of the control panel.
When turned to ON, initiates the electronic ignition system.
Combination Control Valve — Controls gas flow to the main burner. The valve has a built in
gas pressure regulator which shuts off all gas in the event of pilot
outage.
Pressure Gauge
— Indicates pressure in the jacket, normal operating range is 0 to
12 psig.
LID
LID
KETTLE
JACKET
KETTLE
JACKET
ON – OFF SWITCH
OFF
OFF
THERMOSTAT
THERMOSTAT
PRESSURE GAUGE
PRESSURE GAUGE
JACKET WATER LEVEL
JACKET WATER LEVEL
COMBINATION
COMBINATION
CONTROL VALVE
CONTROL VALVE
(Built before September 2003)
(Built before November 2002)
Fig. 2
Fig. 3
CONTROLS — KETTLES WITH MANUAL PILOT BURNER (Prior Construction, Fig. 3)
Thermostat
— Controls heat in the kettle. High dial settings are for cooking; low
settings are for holding.
Combination Control Valve — Controls gas flow to the main burner. The valve has a built in
gas pressure regulator which shuts off all gas in the event of pilot
outage.
Pressure Gauge
— Indicates pressure in the jacket, normal operating range is 0 to
12 psig.
– 8 –
Download from Www.Somanuals.com. All Manuals Search And Download.
KETTLE FEATURES — COMMON TO ALL CONSTRUCTIONS (Fig. 4)
CONTROLS ENCLOSURE
HANDLE
LID
PRESSURE RELIEF VALVE
THERMOSTATIC AIR VENT
(PRESSURE LIMIT SWITCH, ETC.)
VACUUM BREAKER
FILL ASSEMBLY
UPPER VALVE — OPEN
SIGHT GLASS
FOOD
DRAW-OFF
VALVE
WATER LEVEL
LOWER VALVE — OPEN
Fig. 4
Low Water Cutoff
— Pilot and Main Burner won't operate if water level in jacket is low.
Pressure Relief Valve
Pressure Limit Switch
— Protect the kettle against excessive pressure should the thermo-
stat malfunction. The pressure relief valve is rated so that it will
relieve generated steam faster than the burners can generate it.
Thermostatic Air Vent
Vacuum Breaker
— Allows air to vent out of the jacket as steam is generated; closes
at approximately 180°F (82.2°C) to prevent the steam from escaping.
— Allows air to enter the jacket after cooldown, preventing negative
pressure.
Sight Glass Assembly
Fill Assembly
— Visually shows the water level in the jacket when both valves are
open and pressure is equalized.
— Tube where water can be added to the jacket. A manual valve
and a check valve are provided to protect you should the manual
valve be inadvertently opened while the jacket is under pressure.
Food Draw-Off Valve
— Allows food and liquid to be drawn off from the kettle.
FOOD DRAW-OFF VALVE
The food draw-off valve is designed to allow food and liquid to be removed from the kettle in an
easy and safe manner. When the food draw-off valve is off, the valve handle is pointed to either
the 9 o'clock position or the 3 o'clock position as you look down on the valve. In this off position,
no liquid or food product will flow. To open the valve and allow liquid or food product to flow,
slowly turn handle forward. With the valve handle pointing to the 6 o'clock position, the valve is
fully open. Turn the valve 90 degrees right or 90 degrees left to close the valve and shut off the
flow of food. Stir the food product in the kettle thoroughly before opening the draw-off valve; this
makes the food product evenly mixed before it flows into a suitable food service pan or stock pot.
Pans or pots may be placed on a portable dolly for ease of movement and handling. Refer to
Cleaning, page 11.
– 9 –
Download from Www.Somanuals.com. All Manuals Search And Download.
TURNING ON A KETTLE EQUIPPED WITH ELECTRONIC IGNITION (Applies to Fig. 1 or Fig. 2)
Before lighting the pilot, both the burner and pilot must have been off at least 5 minutes.
1. Remove the control panel cover screw.
2. Remove the control box cover (lift, pull out at bottom, lower).
3. Turn knob of the combination control valve counterclockwise until it stops at the ON position.
4. Replace the control panel cover and screw. Check proper jacket water level: Refer to Fig. 4,
page 9, and Jacket Water & Jacket Water Treatment, page 12.
5. Make sure gas supply is on. Turn the On-Off switch to the ON position.
6a.On kettles built after September 2003, the pilot begins sparking and the pilot burner indicator
light illuminates. The pilot burner and indicator light remain on as long as the On-Off switch
remains on. If the pilot burner goes out, the kettle controls automatically attempt to relight the
pilot for 90 seconds, followed by a 5 minute wait (this repeats until pilot lights or switch is
turned off).
6b.On kettles built from October 1998 to September 2003, the pilot begins sparking only when
the thermostat calls for heat from the main burners. The pilot burner cycles on and off with the
main burners. If the pilot burner goes out, turn the On-Off switch off for 5 minutes before
attempting to restart the pilot by turning the switch back on.
6c. On kettles built before October 1998, the pilot begins sparking and the pilot lights. The pilot
stays on as long as the On – Off switch remains on. If the pilot burner goes out, turn the On-
Off switch off for 5 minutes before attempting to restart the pilot by turning the switch back on.
7. The lit pilot can be viewed through the view port at lower front of kettle.
8. Use thermostat to regulate cooking temperatures.
TURNING ON A KETTLE EQUIPPED WITH A MANUAL PILOT BURNER (Applies to Fig. 3)
1. Remove the control box cover screw. Remove the control box cover (lift, pull out at bottom,
then lower).
2. Swing disc to open the lighting hole (lower front).
3. After burners have been off for at least 5 minutes, open the gas shutoff valve.
4. Turn the knob of the combination control valve to the PILOT position. Using a taper, ignite
the pilot (through the lighting hole) while completely depressing the knob of the combination
control valve. Keep the knob depressed for about one minute after the pilot is lit. Release
the knob. The pilot should continue burning. If not, repeat steps 3 and 4.
5. Turn the combination control valve to the ON position.
6. Replace the control box cover. Replace the screw and reconnect the electric power.
7. If pilot light goes out, main burners will not come on. Repeat, starting from step 1.
8. Use thermostat to regulate cooking temperatures.
SHUTDOWN
Turn the thermostat dial to the OFF position. If equipped with an On-Off switch, turn it off. To
completely shut off, close the gas shutoff valve. Turn combination gas control valve off.
– 10 –
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING
After each use, clean and flush the kettle liner immediately, especially if the product cooked
contained salt, vinegar or acid in any concentration. Do not use chlorine based cleaning
products. Do not use metalic scouring pads or brushes.
Daily — Kettle Food Draw-Off Valve
CAUTION: During disassembly, cleaning and reassembly of the valve, take special care to
avoid damage to the mating surfaces of the valve plug and valve body. Do not allow the
valve plug to contact metal or hard surfaces during cleaning. Do not use metal utensils or
scouring pads to clean the valve's mating surfaces. Do not drop valve plug. Damage to
the mating surfaces will result in a leaky valve. Damaged valves are not covered under
warranty.
1. Disassemble and clean valve daily. With kettle empty, turn valve handle to the *removable
position. Lift valve plug from valve body. A pin locks the valve plug into the valve body; the
valve plug can only be removed or replaced when the valve handle is at the *removable
position. Do not attempt to slide the valve plug into the valve body when the valve handle is
in any other than the *removable position. This would damage the pin, cause the plug not to
seat properly and cause leakage between the valve plug and the valve body.
* The removable position for valves manufactured after June 2003 is with the handle positioned
at 7 o'clock. The removable position for valves manufactured from March 1992 through June
2003 is with the handle positioned at 4 o'clock. The removable position for valves manufactured
prior to March 1992 is with the handle positioned at 6 o'clock.
2. Using a solution of warm water and detergent, wash the entire valve body the opening that
goes into the kettle interior. Also wash the interior and exterior of the valve plug.
3. After cleaning the valve, lubricate the valve body and valve plug with Petro-Gel lubricant
supplied with kettle. Make sure all interior mating surfaces are covered with this lubricant
before sliding the valve plug into the valve body. Make sure the valve plug handle is in the
*removable position when the plug is slipped carefully into the valve body.
A 4 oz. tube of Petro-Gel lubricant, (P/N 833652) is furnished with your kettle. You can reorder
through your local service agency or food service equipment dealer. There are no substitutes for
this lubricant. If you fail to lubricate the valve body and plug after cleaning or use a substitute
lubricant, this could damage the mating surfaces which is not covered under warranty.
4. If multiple kettles are in use, each draw-off valve body and draw-off plug is stamped with a set
of corresponding numbers. After cleaning and lubricating, make sure the body and plug
numbers match before reinserting the valve plug. Always examine the valve plug and valve
body for nicks and heavy scratches. Do not push or force the valve plug into the valve body
if there are any obstructions, nicks or heavy scratches in either the plug or the valve body.
5. To correct a draw-off valve that is leaking after lubricant has been applied, examine the
mating surfaces of the valve body and valve plug and carefully dress any raised places with
a very fine file or emery cloth. Do not cut below metal surface in removing any raised places.
Coat plug lightly with lapping compound, insert plug into valve body and rotate back and forth
several times to seat plug into valve body. Use medium grade lapping compound first and
finish with a fine grade. Valve grinding compound from an automobile supply house is suitable
for this. After use of lapping compound, clean surfaces thoroughly. Lubricate surfaces with
Petro-Gel lubricant. If the valve still leaks after lapping, repeat the lapping procedure.
– 11 –
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WARNING: THE KETTLE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING,
CLEANING AND SERVICING THE KETTLE.
WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW
LOCKOUT / TAGOUT PROCEDURE.
PRESSURE RELIEF VALVE
Open the pressure relief valve at least once a day to avoid lime build-up. If leakage occurs or
if the valve opens below the rated psi, it will need to be replaced by your Vulcan authorized
servicer.
LOW WATER CUT-OFF
This device should be removed and inspected for lime build-up at least once a year. The float
must move freely in its cage. Clean if necessary. Replace if lime or sludge cannot be removed
to allow the float to move freely. Contact your local Vulcan authorized servicer.
JACKET WATER & JACKET WATER TREATMENT
The kettle jacket is filled at the factory with chemically pure water mixed with a boiler treatment
corrosion inhibitor. During normal kettle operation, it should not be necessary to frequently add
water to the kettle jacket. If the water level in the sight glass falls below half, add distilled or
chemically pure water to the jacket through the fill tube. The water level in the sight glass should
be maintained to just above the halfway position in the sight glass.
If the water in the sight glass appears dirty, it is necessary to have a qualified service technician
remove the fluid in the kettle, perform a delime or cleaning operation and refill the kettle with
distilled, chemically pure water with a boiler treatment additive.
Do not fill kettle jacket with chlorinated tap water. Appliance failure caused by water quality is
not covered under warranty.
HOOD VENTILATION SYSTEM
Annually, when cool, check the ventilation system and clear any obstructions.
SERVICE AND PARTS INFORMATION
To obtain service and parts information concerning the kettle, contact the Vulcan-Hart Service
Agency in your area (refer to listing supplied with the kettle), or Vulcan-Hart Company Service
Department at the address or phone number shown on the front cover of this manual.
FORM 30960 Rev. B (Oct. 2003)
PRINTED IN U.S.A.
– 12 –
Download from Www.Somanuals.com. All Manuals Search And Download.
|