4
Selected resolution
High:600 dpi / Low:300 dpi
4.7 Stitch file
4. Using the scanner
To group scanned files into a new folder within the microSD card use the Stitch file function.
4.1 Charging the battery
1.
Press the [STITCH FILE] button to create a new folder within the microSD card for files
storage. SF white LED light will turn on.
PDS-ST510-VP Manual
1.
2.
Before first using the scanner, it is recommended to charge the battery for 6-8 hours.
To charge, connect the scanner to a (1) USB 2.0 port or (2) an outlet with the power
adapter included. When charging, “Err” (Error) red light will be lit and will turn off once
the battery is fully charged.
2.
3.
Then scan your documents. Your files will be saved into the new folder.
To save another new set of scans in another folder, press the [STITCH FILE] button
again to generate a new folder.
1. Key features
Note: Do not remove the battery from the battery compartment.
600/300 dpi resolution scan selection
For free optional stitching software, please download the program from the following link:
Directly save JPEG file to microSD/microSDHC card
Supports microSD/microSDHC card up to 32GB
Driver free to download for Windows® XP, Windows® Vista™,
Windows® 7 and Mac OS® 10.4 or above
4.2 Inserting a microSD memory card (not included)
To operate the scanner, you must insert a microSD Card (not supplied) to record and store your
pictures. Inserting the microSD memory card:
4.8 How to scan
Note: To scan, make sure your scanner is not connected to the computer.
(direct plug-in, driver installation not required)
1.
2.
Turn OFF the scanner.
Insert the microSD card into the microSD card slot (with metal side facing upwards).
1.
2.
3.
Turn on the scanner by sliding the [POWER] button to ON.
2. Functional parts
Place the document on a flat surface and hold down the document with one hand.
Place the scanner on the edge of the paper approximately 5/8 to 3/4 of an inch onto the
paper to ensure the most of the document can be scanned. Make sure to keep the
scanning area in between the scanning width indicator marked on the side of the
scanner.
Gently press in until card is clicked in and latched. The SD card indicator
appear on the LCD screen.
must
Note: Do not force the card into the slot; forcing may damage scanner and the microSD memory
card. Align microSD card position (as marked) and try again.
4.
Hold the scanner flat against the material and then press the [SCAN] button once.
4.3 Time setting
1.
Press [TIME SET] button to enter time setting mode by using a thin, blunt object, such
as a paperclip to access the button. The LCD screen will read “1##” (step 1) for the year.
“##” is a set of number that would be changed to correspond to the actual time/date
setting. The numbers 1-5 in front of “##” indicates each step in the settings.
Press the [STITCH FILE] or [DPI] buttons to select the current Year.
Part
Function
2.
3.
4.
Press [SCAN] button to confirm setting. The LCD screen will now read “2##.”
Repeat steps 2 and 3 to select the Month, Date, Hour, and Minute.
Select High(600dpi) / Low(300dpi) resolution;
High / Low resolution mode icon will be displayed on
status LCD screen.
1
Resolution
Indicator
Setting
Year
Month
Date
Hour
Minute
2
3
Stitch file
Create new folder for file storage.
1##
2##
3##
4##
5##
5.
6.
Slide the scanner slowly, keeping you hand stable to get the best quality picture.
Press the [SCAN] button again to stop scanning.
Power On/Off: Switch this key left or right to turn
scanner on or off.
Power button
In power on mode, press this button to start scanning,
press this button again to stop scanning
4
5
Scan
5. LED light indications
5
After setting the Minute, “5##”, press the [TIME SET] button again to complete the Time
Scan LED indicator
Error LED indicator
Ready for scan: Green LED on
and Date setting.
6
7
8
9
Over speed: Red LED on
Scanning status display
Stitch file: White LED on
For 4.2V rechargeable battery
4.4 Formatting the microSD memory card
Note: Formatting the microSD is recommended but not necessary. All contents on the microSD
card will be erased during formatting.
LCD screen
SF LED indicator
Battery door
1.
Insert a microSD card into the scanner with metal side facing upwards. Then power on
the scanner.
Press the [FORMAT] button with a thin, blunt object, such as the end of a paperclip to
access the button. An “F” shows on the LCD screen.
Press the [SCAN] button once to begin formatting microSD card.
The microSD card indicator will blink until the formatting process is complete.
“GREEN” SCAN LED ON
Scan in progress.
10
11
microSD card slot
USB interface
microSD/microSDHC card storage location.
2.
“GREEN” SCAN LED OFF
Standby / Scan is complete.
----------------------------------------------------------------------------------------------------
Download photo to a computer via USB cable provided.
3.
4.
“RED” ERROR LED ON
Scanning too fast.
12
13
Time set
Press to enter Time and Date setting mode
May cause scanning error.
Restart and scan again.
4.5 Calibrating your scanner
Note: Perform calibration only when white balance needs adjustment.
Format button
Press this button to format the microSD/SDHC card.
1.
Turn on the scanner by sliding the [POWER] button to ON. Then place the scanner on
the provided “White Balance Calibration” paper.
Click and hold onto the [STITCH FILE] button. While holding onto the [STITCH FILE]
“RED” ERROR LED OFF
No error in scanning speed.
Continue scanning process.
3. Explanation of the status icons
2.
---------------------------------------------------------------------------------------------------------------------
button, press the [SCAN] button once and then release both buttons. SD symbol
flash and “GREEN” and “RED” LED light will turn on.
will
“WHITE” SF LED ON/OFF
A new folder created.
3.
4.
Do not move the scanner. Wait until the “RED” LED light turns off. “GREEN” LED light
will stay on.
With only the “GREEN” LED light on, start scanning the white paper by sliding the
scanner across the paper until the “GREEN” LED light turns off. (Slide the scanner
backwards if necessary).
﹡Scan will START when
button is pressed
button again
﹡To END scan, press
Item
1
Function
Description
5.
Slide the [POWER] button to OFF to turn off the scanner. Calibration is complete.
SD card indicator
Photos will be stored in microSD card
4.6 Setting the resolution
2
3
Battery indicator
Battery is full
Empty battery
1.
By pressing the [DPI] resolution button on the scanner, you may choose between high
resolution (600 dpi) and low resolution (300 dpi).
The high or low resolution mode will be displayed on the LCD screen to reflect your
choice.
Counting indicator
Show scanned files in microSD card
2.
Download from Www.Somanuals.com. All Manuals Search And Download.
|