®
ViewSonic
- User Guide
- Guide de l’utilisateur
- Bedienungsanleitung
- Guía del usuario
- Guida dell’utente
- Guia do usuário
- Användarhandbok
- Käyttöopas
PJD5211/PJD5221/
PJD5231/PJD5122
DLP Projector
- Руководство пользователя
- 使用手冊 (繁體)
- 使用手冊 (簡體)
IMPORTANT: Please read this User Guide to obtain important information on install-
ing and using your product in a safe manner, as well as registering your product for
future service. Warranty information contained in this User Guide will describe your
limited coverage from ViewSonic Corporation, which is also found on our web site
selection box in the upper right corner of our website.
- 사용자 안내서
- Podręcznik użytkownika
- Kullanιcι kιlavuzu
“Antes de operar su equipo lea cuidadosamente las instrucciones en este manual”
Model No. : VS13304/VS13305
VS13306/VS13308
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/EC of the
European Parliament and the Council on restriction of the use of certain hazardous substances in
electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum
concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:
Proposed Maximum
Substance
Actual Concentration
Concentration
Lead (Pb)
0.1%
0.1%
0.01%
0.1%
0.1%
0.1%
< 0.1%
< 0.1%
< 0.01%
< 0.1%
< 0.1%
< 0.1%
Mercury (Hg)
Cadmium (Cd)
6+
Hexavalent Chromium (Cr
)
Polybrominated biphenyls (PBB)
Polybrominated diphenyl ethers (PBDE)
Certain components of products as stated above are exempted under the Annex of the RoHS Directives
as noted below:
Examples of exempted components are:
1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other lamps not
specifically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and electronic ceramic
parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium containing up
to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright Information
Copyright© ViewSonic® Corporation, 2010. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of
ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are
trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this material, or
the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change
product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes available,
ROM also provides an opportunity for you to print the registration form, which you may mail or fax to
ViewSonic.
For Your Records
Product Name:
PJD5211/PJD5221/PJD5231/PJD5122
ViewSonic DLP Projector
Model Number:
Document Number:
Serial Number:
Purchase Date:
VS13304/VS13305/VS13306/VS13308
PJD5211_5221_5231_5122_UG_ENG Rev. 1A 02-23-10
______________________________________________
______________________________________________
The lamp in this product contains mercury.
Please dispose of in accordance with local, state or federal laws.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
Important safety
instructions .......................3
Positioning your
projector..........................11
Copyright
information .....................54
Magnifying and searching for
Operating in a high altitude
Personalizing the projector menu
2
Table of contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1.
Please read this manual before you operate your projector. Save it for future
reference.
2.
Do not look straight at the projector lens during operation. The intense light beam
may damage your eyes.
3.
4.
Refer servicing to qualified service personnel.
Always open the lens shutter or remove the lens cap when the projector lamp is
on.
5.
In some countries, the line voltage is NOT stable. This projector is designed to operate
safely within a mains voltage between 100 to 240 volts AC, but could fail if power
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector or uninterruptible power supply (UPS).
Do not block the projection lens with any objects when the projector is under
operation as this could cause the objects to become heated and deformed or even
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or
remote control.
6.
7.
8.
9.
The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.
Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond the rated life could cause them to break on rare occasions.
Never replace the lamp assembly or any electronic components unless the projector is
unplugged.
10. Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.
11. Do not attempt to disassemble this projector. There are dangerous high voltages inside
which may cause death if you should come into contact with live parts. The only user
serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.
12. Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of a
car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical
components, shortening the projector's life span and darkening the picture.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C / 104°F
- Locations where the altitudes are higher than 3000 m (10000 feet).
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
3
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a fire.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
14. Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of
more than 15 degrees front to back. Using the projector when it is not fully horizontal
may cause a malfunction of, or damage to, the lamp.
15. Do not stand the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage to the projector.
16. Do not step on the projector or place any objects upon it. Besides probable physical
damage to the projector, doing so may result in accidents and possible injury.
17. Do not place liquids near or on the projector. Liquids spilled into the projector may
cause it to fail. If the projector does become wet, disconnect it from the power
supply's wall socket and call your local service center to have the projector serviced.
18. This product is capable of displaying inverted pictures for ceiling mount installation.
Use only qualified ceiling mount kit for mounting the projector and ensure it is
securely installed.
19. When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. It is a normal phenomenon and not a product defect.
20. Do not use the Security bar for transporting or installation. It should be used with a
commercially available theft prevention cable.
Safety instructions for ceiling mounting of the
projector
We want you to have a pleasant experience using your projector, so we need to bring this
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector.
We recommends that you also purchase a separate Kensington lock compatible security
cable and attach it securely to both the Kensington lock slot on the projector and the base of
the ceiling mount bracket. This will perform the secondary role of restraining the projector
should its attachment to the mounting bracket become loose.
4
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
•
•
•
Screen Color correction allowing projection on surfaces of several predefined colors
Quick auto search speeding up the signal detecting process
Up to 8 sets of picture modes providing multiple choices for different projection
purposes
•
•
•
•
•
•
•
•
•
•
Selectable quick cooling function makes the projector cool in a shorter time
One-key auto-adjustment to display the best picture quality
Digital keystone correction to correct distorted images
Adjustable color balance control for data/video display
High brightness projection lamp
Ability to display 16.7 million colors
Multi-language On-Screen Display (OSD) menus
Switchable normal and economic modes to reduce the power consumption
Component HDTV compatibility (YPbPr)
High quality manual zoom lens
•
The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input signal contrast/brightness settings, and is directly
proportional to projection distance.
•
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these
items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
Projector
Power Cord
VGA Cable
Multi-language user manual
DVD
Quick Start Guide
Remote Control & Battery
Pull the tab before using the remote
control.
Optional accessories
1.
2.
3.
Ceiling mount
Replacement lamp
Soft carry case
6
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector exterior view
Front/upper side
1.
External control panel
on page 8 for details.)
Vent (heated air exhaust)
Quick-release button
Lens cover
Focus ring and Zoom ring
Front IR remote sensor
Projection lens
2.
3.
4.
5.
6.
7.
8.
9.
AC power cord inlet
RS-232 control port
10. RGB signal output socket
11. RGB (PC)/Component video
(YPbPr/YCbCr) signal input
socket-1
12. RGB (PC)/Component video
(YPbPr/YCbCr) signal input
socket-2
Rear/lower side
13. Video input socket
14. S-Video input socket
15. Audio signal input socket
16. Audio signal output socket
17. Kensington anti-theft lock slot
18. Quick-release foot
19. Lamp cover
20. Rear adjuster foot
21. Security bar
Connects a commercially available
theft prevention cable.
Warning
THIS APPARATUS MUST BE EARTHED.
•
•
When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring,
or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should
occur during operation of the unit, operate the disconnect device to switch the power supply
off, or disconnect the power plug.
Introduction
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and functions
Projector and remote control
1.
2.
3.
4.
Focus ring
I
5.
6.
POWER
Adjusts the focus of the projected image.
clarity" on page 26 for details.
Zoom ring
Toggles the projector between standby
mode and on. See "Starting up the
the projector" on page 35 for details.
Keystone/Arrow keys (
Down)
Adjusts the size of the image. See "Fine-
26 for details.
TEMPerature indicator light
Lights up red if the projector's temperature
becomes too high. See "Indicators" on page
49 for details.
/
Up,
/
Manually corrects distorted images
resulting from an angled projection. See
details.
7.
8.
Left/Blank
POWER indicator light
Hides the screen picture. See "Hiding the
image" on page 33 for details.
MENU/EXIT
Lights up or flashes when the projector is
under operation. See "Indicators" on page
49 for details.
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings. See "Using
the menus" on page 21 for details.
8
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
LAMP indicator light
17. Enter
Enacts the selected On-Screen Display
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
details.
(OSD) menu item.
18. Keystone keys (
/
)
Manually corrects distorted images
resulting from an angled projection.
19. Magnify keys (+, -)
10. AUTO
Automatically determines the best picture
timings for the displayed image. See
details.
Magnifies or reduces the projected
picture size. See "Magnifying and
details.
11.
Right
20. Blank
Activates panel key lock. See "Locking
control keys" on page 33 for details.
When the On-Screen Display (OSD)
keys are used as directional arrows to
select the desired menu items and to make
adjustments. See "Using the menus" on
page 21 for details.
Hides the screen picture. See "Hiding the
image" on page 33 for details.
21. Source selection keys (VGA 1/VGA 2/
Video)
Selects an input source for display.
22. Exit
Goes back to previous OSD menu, exits
and saves menu settings.
12. MODE/ENTER
Selects an available picture setup mode.
23.
for details.
Toggles the projector audio between on
and off.
24. Color Mode
Enacts the selected On-Screen Display
(OSD) menu item.
Selects an available picture setup mode.
29 for details.
13. SOURCE
Displays the source selection bar. See
details.
25. Volume keys (+, -)
Magnifies or reduces the volume level.
14. Freeze
Freezes the projected image. See
details.
15.
/
/
/
Selects the desired menu items and makes
adjustments. See "Using the menus" on
page 21 for details.
16. MENU
Turns on the On-Screen Display (OSD)
menu.
Introduction
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control effective range
Infra-Red (IR) remote control sensor is located on
the front of the projector. The remote control must be
held at an angle within 30 degrees perpendicular to
the projector's IR remote control sensor to function
correctly. The distance between the remote control
and the sensor should not exceed 8 meters (~ 26
feet).
Make sure that there are no obstacles between the
remote control and the IR sensor on the projector that
might obstruct the infra-red beam.
Replacing the remote control battery
1.
Pull out the battery holder.
Please follow the illustrated instructions. Push and
hold the locking arm while pulling out the battery
holder.
1
2
2.
3.
Insert the new battery in the holder. Note the
positive polarity should face outward.
Push the holder into the remote control.
CAUTION
•
•
•
•
•
•
Avoid excessive heat and humidity.
There may be battery damage if the battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the battery manufacturer.
Dispose of the used battery according to the battery manufacturer’s instructions.
Never throw a battery into a fire. There may be danger of an explosion.
If the battery is dead or if you will not be using the remote control for a long time, remove
the battery to prevent damage to the remote control from possible battery leakage.
10
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Your projector is designed to be installed in one of four possible installation locations:
1.
Front Table
Select this location with the projector placed near
the floor in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
2.
Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the
screen.
Purchase the projector ceiling mount kit from your
dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM SETUP:
Basic > Projector Position menu after you turn
the projector on.
3.
Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
projector ceiling mounting kit are required for this
installation location.
Set Rear Ceiling in the SYSTEM SETUP: Basic
> Projector Position menu after you turn the
projector on.
4.
Rear Table
Select this location with the projector placed near
the floor behind the screen.
Note that a special rear projection screen is
required.
Set Rear Table in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the
projector on.
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Projection dimensions
calculating the appropriate position.
•
4:3 image on a 4:3 screen
(a)
(b)
(e)
(a)
(f)
(d)
(c)
(c)
(d)
(f)
(e)
(b)
•
16:9 image on a 4:3 screen
(b)
(a)
(a)
(e)
(f)
(d)
(c)
(c)
(d)
(f)
(b)
(e)
(e): Screen
(f): Center of lens
4:3 Screen
16:9 Screen
(a) Screen
Size
[inch (m)]
(b) Projection distance
[m (inch)]
(b) Projection distance
[m (inch)]
(c) Image (d)Vertical
height offset
[cm (inch)] [cm (inch)]
(c) Image (d)Vertical
height offset
[cm (inch) [cm (inch)]
min.
max.
min.
max.
40 (1.0) 1.5 (60) 1.7 (66) 61 (24)
50 (1.3) 1.9 (75) 2.1 (82) 76 (30)
60 (1.5) 2.3 (90) 2.5 (98) 91 (36)
70 (1.8) 2.7 (105) 2.9 (115) 107 (42)
80 (2.0) 3.0 (120) 3.4 (132) 122 (48)
90 (2.3) 3.4 (135) 3.8 (148) 137 (54)
100 (2.5) 3.8 (150) 4.2 (165) 152 (60)
120 (3.0) 4.6 (180) 5.0 (198) 183 (72)
3
4
5
5
6
7
8
9
(1) 1.5 (60) 1.7 (66) 46 (18) 11 (4)
(2) 1.9 (75) 2.1 (82) 57 (23) 13 (5)
(2) 2.3 (90) 2.5 (99) 69 (27) 16 (6)
(2) 2.7 (105) 2.9 (115) 80 (32) 19 (7)
(2) 3.0 (120) 3.4 (132) 91 (36) 21 (8)
(3) 3.4 (135) 3.8 (148) 103 (41) 24 (10)
(3) 3.8 (150) 4.2 (165) 114 (45) 27 (11)
(4) 4.6 (180) 5.0 (198) 137 (54) 32 (13)
150 (3.8) 5.7 (225) 6.3 (247) 229 (90) 11 (5) 5.7 (225) 6.3 (247) 171 (68) 40 (16)
200 (5.1) 7.6 (300) 8.4 (330) 305 (120) 15 (6) 7.6 (300) 8.4 (330) 229 (90) 53 (21)
250 (6.4) 9.5 (375) 10.5 (412) 381 (150) 19 (8) 9.5 (375) 10.5 (412) 286 (113) 67 (26)
300 (7.6) 11.4 (450) 12.5 (495) 457 (180) 23 (9) 11.4 (450) 12.6 (495) 343 (135) 80 (32)
There is 3% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should physically
test the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
12
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 6). They are commercially available from electronics stores.
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1.
2.
3.
Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal input socket on the projector.
If you wish to make use of the projector (mixed mono) speaker in your presentations,
take a suitable audio cable and connect one end of the cable to the audio output socket
of the device, and the other end to the AUDIO IN socket of the projector.
If you wish, you can use another suitable audio cable and connect one end of the cable
to the AUDIO OUT socket of the projector, and the other end to your external
speakers (not supplied).
4.
Once connected, the audio can be controlled by the projector On-Screen Display
(OSD) menus.
The final connection path should be like that shown in the following diagram:
Notebook or desktop computer
Speakers
or
VGA cable
Audio
cable
Audio cable
Connection
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the COMPUTER OUT signal output socket on the projector to an external
monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1.
Connect the projector to a computer as described in "Connecting a computer" on page
13.
2.
Take a suitable VGA cable (only one supplied) and connect one end of the cable to the
D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
Connect the other end of the cable to the COMPUTER OUT socket on the projector.
3.
The final connection path should be like that shown in the following diagram:
Notebook or desktop
computer
Monitor
VGA to DVI-
A cable
or
VGA cable
VGA cable
•
•
The COMPUTER OUT output only works when COMPUTER IN 1 or COMPUTER IN 2 is
made to the projector.
To use this connection method, make sure the Active VGA Out and Active Audio Out
41 for details.
14
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
•
•
•
Component Video
S-Video
Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is Component Video (not to be confused with
composite Video). Digital TV tuner and DVD players output Component Video natively, so
if available on your devices, this should be your connection method of choice in preference
to (composite) Video.
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
projector to a composite Video device.
Connecting audio
The projector has one built-in mono speaker which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. They are not
designed for, nor intended for stereo audio reproduction use as might be expected in home
theater or home cinema applications. Any stereo audio input (if provided), is mixed into a
common mono audio output through the projector speaker.
If you wish, you can make use of the projector (mixed mono) speaker in your presentations,
and also connect separate amplified speakers to the Audio Out socket of the projector. The
audio output is a mixed mono signal and controlled by the projector Volume and Mute
settings.
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
Connection
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1.
Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3
RCA type connectors to the Component Video output sockets of the Video source
device. Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
2.
3.
4.
Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a
D-Sub type connector) to the COMPUTER IN 1 or COMPUTER IN 2 socket on the
projector.
If you wish to make use of the projector (mixed mono) speaker in your presentations,
take a suitable audio cable and connect one end of the cable to the audio output socket
of the device, and the other end to the AUDIO IN socket of the projector.
If you wish, you can use another suitable audio cable and connect one end of the cable
to the AUDIO OUT socket of the projector, and the other end to your external
speakers
Once connected, the audio can be controlled by the projector On-Screen Display
(OSD) menus.
The final connection path should be like that shown in the following diagram:
AV device
Speakers
Component Video to VGA
(D-Sub) adaptor cable
or
Audio
cable
Audio cable
•
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
VGA-Component adapter
(ViewSonic P/N: CB-00008906)
•
16
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1.
Take an S-Video cable and connect one end to the S-Video output socket of the Video
source device.
2.
3.
Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
If you wish to make use of the projector (mixed mono) speaker in your presentations,
take a suitable audio cable and connect one end of the cable to the audio output socket
of the device, and the other end to the AUDIO IN socket of the projector.
If you wish, you can use another suitable audio cable and connect one end of the cable
to the AUDIO OUT socket of the projector, and the other end to your external
speakers
4.
Once connected, the audio can be controlled by the projector On-Screen Display
(OSD) menus.
The final connection path should be like that shown in the following diagram:
AV device
Speakers
Audio cable
Audio
cable
S-Video cable
•
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to this
device using an S-Video connection as this makes an unnecessary second connection of
Connection
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1.
Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
2.
3.
Connect the other end of the Video cable to the VIDEO socket on the projector.
If you wish to make use of the projector (mixed mono) speaker in your presentations,
take a suitable audio cable and connect one end of the cable to the audio output socket
of the device, and the other end to the AUDIO IN socket of the projector.
If you wish, you can use another suitable audio cable and connect one end of the cable
to the AUDIO OUT socket of the projector, and the other end to your external
speakers
4.
Once connected, the audio can be controlled by the projector On-Screen Display
(OSD) menus.
The final connection path should be like that shown in the following diagram:
Speakers
Video cable
AV device
Audio
cable
Audio cable
•
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source devices"
on page 15 for details.
18
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Starting up the projector
1.
Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted). Check that the POWER
indicator light on the projector flashes blue
after power has been applied.
2.
Remove the lens cap. If it is closed, it could
become deformed due to the heat produced by
the projection lamp.
I
3.
Press
POWER on the projector or remote
control to start the projector. The POWER
indicator light stays blue when the projector is
on.
The start up procedure takes about 30 seconds.
In the later stage of start up, a startup logo is
projected.
(If necessary) Rotate the focus ring to adjust the
image clearness.
•
If the projector is still hot from previous activity, it will run the cooling fan for
approximately 90 seconds before energizing the lamp.
•
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before
turning it off.
4.
If the projector is activated for the first time,
select your OSD language following the on-
screen instructions.
5.
Switch all of the connected equipment on.
Operation
19
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the message 'No Signal' will continue to be displayed until an input
signal is found.
You can also press SOURCE on the projector or remote control to select your desired
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
20
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
Below is the overview of the OSD menu.
Main menu icon
Screen Color
Off
Aspect Ratio
Keystone
Position
Auto
Highlight
Sub-menu
ENTER
Status
Phase
16
0
H. Size
Zoom
Go to the
previous page
or to exit.
3D Sync
3D Sync Invert
Color Management
On
Disable
Analog RGB
MENU Exit
Current input
signal
To use the OSD menus, please set them to your familiar language first.
1.
Press MENU/EXIT on the projector or
MENU on the remote control to turn the
OSD menu on.
3.
Press
Language and press
select a preferred language.
to highlight
/
to
Screen Color
Aspect Ratio
Keystone
Off
Auto
Position
16
0
Phase
H. Size
Zoom
3D Sync
On
Disable
3D Sync Invert
Color Management
Analog RGB
Exit
MENU
Language
English
Projector Position
Auto Power Off
Blank Timer
Front Table
Disable
Disable
Off
2.
Use
/
to highlight the SYSTEM
Panel Key Lock
SETUP: Basic menu.
Timer Controller
Disable
ViewSonic
Splash Screen
Language
English
Analog RGB
MENU Exit
Projector Position
Auto Power Off
Blank Timer
Front Table
Disable
Disable
4.
Press MENU/EXIT twice* on
the projector or Exit on the
remote control to leave and
save the settings.
Panel Key Lock
Off
Timer Controller
Disable
Splash Screen
Analog RGB
ViewSonic
MENU Exit
*The first press leads you back
to the main menu and the
second press closes the OSD
menu.
: DISPLAY
: PICTURE
: SOURCE
: SYSTEM SETUP: Basic
: SYSTEM SETUP: Advanced
: INFORMATION
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on
You will be inconvenienced if you activate the password functionality and subsequently forget
the password. Print this user manual (if necessary) and write the password you used in this
manual, and keep it in a safe place for later use.
Setting a password
Once a password has been set, the projector cannot be used unless the correct password is
entered every time the projector is started.
1.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings menu. Press MODE/ENTER on the projector or Enter on the remote
control. The Security Settings page is displayed.
2.
3.
Highlight Power On Lock and select On by pressing
As pictured to the right, the four arrow keys (
) respectively represent 4 digits (1, 2,
3, 4). According to the password you desire to
/
.
,
INPUT NEW PASSWORD
,
,
set, press the arrow keys to enter six digits for the
password.
4.
Confirm the new password by re-entering the
new password.
MENU Back
Once the password is set, the OSD menu returns to the Security Settings page.
The digits being input will be displayed as asterisks on-screen. Write your selected password
down here in this user manual in advance or right after the password is entered so that it is
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
5.
To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control.
If you forget the password
If the password function is activated, you will be asked
to enter the six-digit password every time you turn on
the projector. If you enter the wrong password, the
password error message as pictured to the right is
displayed lasting for three seconds, and the message
'INPUT PASSWORD' follows. You can retry by
entering another six-digit password, or if you did not
Password Error
Please try again.
record the password in this user manual, and you absolutely do not remember it, you can use
details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
22
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering the password recall procedure
1.
Press and hold AUTO on the projector or remote
control for 3 seconds. The projector will display
a coded number on the screen.
RECALL PASSWORD
Please write down the recall code,
and contact ViewSonic
Customer Center.
2.
3.
Write down the number and turn off your
projector.
Seek help from the local service center to decode
the number. You may be required to provide
proof of purchase documentation to verify that
you are an authorized user of the projector.
Recall code:
0 2 1 2
Exit
MENU
Changing the password
1.
2.
3.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings > Change Password menu.
Press MODE/ENTER on the projector or Enter on the remote control. The message
'INPUT CURRENT PASSWORD' is displayed.
Enter the old password.
•
If the password is correct, another message 'INPUT NEW PASSWORD' is
displayed.
•
If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT CURRENT PASSWORD' is
displayed for your retry. You can press MENU/EXIT on the projector or Exit
on the remote control to cancel the change or try another password.
4.
Enter a new password.
The digits being input will be displayed as asterisks on-screen. Write your selected password
down here in this user manual in advance or right after the password is entered so that it is
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
5.
6.
Confirm the new password by re-entering the new password.
You have successfully assigned a new password to the projector. Remember to enter
the new password next time the projector is started.
7.
To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control .
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security
Settings > Power On Lock menu after opening the OSD menu system. Select Off by
pressing
/
. The message 'INPUT PASSWORD' is displayed. Enter the current
password.
•
•
If the password is correct, the OSD menu returns to the Security Settings page
with 'Off' shown in the row of Power On Lock. You will not have to enter the
password next time you turn on the projector.
If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT PASSWORD' is displayed for your
Operation
23
Download from Www.Somanuals.com. All Manuals Search And Download.
retry. You can press MENU/EXIT on the projector or Exit on the remote
control to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.
Be sure the Quick Auto Search function in the SOURCE menu is On if you want the
projector to automatically search for the signals.
You can also manually cycle through the available
input signals.
1.
Press SOURCE on the projector or remote
control. A source selection bar is displayed.
2.
Press
/
until your desired signal is
selected and press MODE/ENTER on the
projector or Enter on the remote control.
Once detected, the selected source information
will be displayed on the screen for seconds. If
there are multiple devices connected to the
signal.
D-Sub / Comp. 1
D-Sub / Comp. 2
Video
•
The brightness level of the projected image will
change accordingly when you switch between
different input signals. Data (graphic) "PC"
presentations using mostly static images are
generally brighter than "Video" using mostly
moving images (movies).
S-Video
•
•
The input signal type effects the options available
for the Color Mode. See "Selecting a picture
mode" on page 29 for details.
The native display resolution of this projector is in a 4:3 aspect ratio. For best display
picture results, you should select and use an input signal which outputs at this resolution.
Any other resolutions will be scaled by the projector depending upon the 'aspect ratio'
setting, which may cause some image distortion or loss of picture clarity. See "Selecting
the aspect ratio" on page 27 for details.
24
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These
adjusters change the image height and projection angle. To adjust the projector:
1.
Press the quick-release button and lift the
front of the projector. Once the image is
positioned where you want it, release the
quick-release button to lock the foot in
position.
2.
Screw the rear adjuster foot to fine tune the
horizontal angle.
1
2
To retract the foot, hold up the projector while
pressing the quick-release button, then slowly
lower the projector. Screw the rear adjuster foot
in a reverse direction.
If the projector is not placed on a flat surface or the screen and the projector are not
perpendicular to each other, the projected image becomes trapezoidal. To correct this
•
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.
•
Be careful when you press the adjuster button as it is close to the exhaust vent where hot
air comes from.
Auto-adjusting the image
In some cases, you may need to optimize the
picture quality. To do this, press AUTO on the
projector or remote control. Within 3 seconds, the
built-in Intelligent Auto Adjustment function will
re-adjust the values of Frequency and Clock to
provide the best picture quality.
The current source information will be displayed
in the upper left corner of the screen for 3 seconds.
•
The screen will be blank while AUTO is
functioning.
•
This function is only available when PC signal
(analog RGB) is selected.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Fine-tuning the image size and clarity
1.
Adjust the projected image to the size that you
need using the zoom ring.
2.
Then sharpen the image by rotating the focus ring.
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
•
Using the remote control
Press on the projector or remote control to
/
display the Keystone correction page. Press
correct keystoning at the top of the image. Press
to
to correct keystoning at the bottom of the image.
•
Using the OSD menu
1.
Press MENU/EXIT on the projector or
MENU on the remote control and then press
/
until the DISPLAY menu is
highlighted.
2.
3.
Press
to highlight Keystone and press
MODE/ENTER on the projector or Enter
on the remote control. The Keystone
correction page is displayed.
Press
/
.
Press
/
.
Press
to correct keystoning at the top of the image or press
to correct
keystoning at the bottom of the image.
26
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
•
Using the remote control
1.
2.
Press Magnify +/- to display the Zoom bar.
Press Magnify + to magnify the center of the
picture. Press the key repeatedly until the
picture size is suitable for your need.
3.
4.
Use the directional arrows (
the projector or remote control to navigate the
picture.
To restore the picture to its original size, press
AUTO. You can also press Magnify -. When
the key is pressed again, the picture is further
reduced until it is restored to the original size.
,
,
,
) on
•
Using the OSD menu
1.
Press MENU/EXIT on the projector or MENU on the remote control and then press
/
until the DISPLAY menu is highlighted.
2.
3.
Press
to highlight Zoom and press MODE/ENTER on the projector or Enter on
the remote control. The Zoom bar is displayed.
using the projector control panel, continue to the following steps.
4.
5.
Press
on the projector repeatedly to magnify the picture to a desired size.
To navigate the picture, press MODE/ENTER on the projector or Enter on the
remote control to switch to the paning mode and press the directional arrows (
,
,
,
) to navigate the picture.
6.
7.
Use the directional arrows (
navigate the picture.
To reduce size of the picture, press MODE/ENTER on the projector or Enter on the
,
,
,
) on the projector or remote control to
remote control to switch back to the zoom in/out functionality, and press AUTO to
restore the picture to its original size. You can also press
restored to the original size.
repeatedly until it is
The picture can only be navigated after the picture is magnified. You can further magnify the
picture while searching for details.
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, which is the default for this projector, and digital TV and DVDs
are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
1.
Press MENU/EXIT on the projector or MENU on the remote control and then press
until the DISPLAY menu is highlighted.
/
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
27
2.
3.
Press
Press
to highlight Aspect Ratio.
/
to select an aspect ratio to suit the format of the video signal and your
display requirements.
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.
1.
Auto: Scales an image proportionally to fit the
projector's native resolution in its horizontal
width. This is suitable for the incoming image
which is neither in 4:3 nor 16:9 and you want to
make most use of the screen without altering the
image's aspect ratio.
16:10 picture
15:9 picture
2.
4:3: Scales an image so that it is displayed in the
center of the screen with a 4:3 aspect ratio. This
is most suitable for 4:3 images like computer
monitors, standard definition TV and 4:3 aspect
DVD movies, as it displays them without aspect
alteration.
4:3 picture
3.
16:9: Scales an image so that it is displayed in
the center of the screen with a 16:9 aspect ratio.
This is most suitable for images which are
already in a 16:9 aspect, like high definition TV,
as it displays them without aspect alteration.
16:9 picture
28
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined
picture modes so that you can choose one to suit
your operating environment and input signal
picture type.
To select an operation mode that suits your need,
you can follow one of the following steps.
•
Press MODE/ENTER on the projector or
Color Mode on the remote control repeatedly
until your desired mode is selected.
•
Go to the PICTURE > Color Mode menu and press
/
to select a desired mode.
Picture modes for different types of signals
The picture modes available for different types of signals are listed below.
PC input signals: D-Sub / Comp. 1/2 (analog RGB)
1.
Brightest mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
2.
3.
4.
Daylight mode: Is designed for presentations under daylight environment to match
PC and notebook coloring.
ViewMatch mode: Switch in between high brightness performance or Accuracy
color performance.
Cinema mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
5.
User 1/User 2 mode: Recalls the settings customized based on the current available
Video input signals: S-Video, Video, D-Sub / Comp. 1/2 (YPbPr)
1.
2.
3.
4.
5.
Brightest mode: Optimized for daylight viewing, with living room level ambient
brightness.
Gaming mode: Suitable for all types of entertainment media, including gaming and
movies.
ViewMatch mode: Switch in between high brightness performance or Accuracy color
performance.
Cinema mode: Is suitable for enjoying dark movies or DVD movies best viewed in a
blackened (little light) home cinema or lounge room environment.
User 1/User 2 mode: Recalls the settings customized based on the current available
Operation
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable
for your need. You can use one of the picture modes (except the User 1/User 2) as a starting
point and customize the settings.
1.
Press MENU/EXIT on the projector or MENU on the remote control to open the On-
Screen Display (OSD) menu.
2.
3.
4.
Go to the PICTURE > Color Mode menu.
Press
Press
/
to select User 1 or User 2.
to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the Color Mode
sub-menu item.
5.
6.
Press
Press
/
to select a picture mode that is closest to your need.
to select a sub-menu item to be changed and adjust the value with
/
.
7.
8.
When all settings have been done, highlight Save Settings and press MODE/ENTER
on the projector or Enter on the remote control to store the settings.
The confirmation message 'Setting Saved' is displayed.
Using Screen Color
In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the Screen Color feature can help correct the projected picture’s colors to
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Screen Color menu and press
/
to select a
color which is closest to the color of the projection surface. There are several precalibrated
colors to choose from: Whiteboard, Greenboard, and Blackboard.
This function is only available when a PC type input signal is selected.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available
when User 1 or User 2 mode is selected. You can make adjustments to these functions
based on your needs.
Adjusting Brightness
Highlight the PICTURE > Brightness menu and press
/
.
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
+50
+70
+30
Adjusting Contrast
Highlight the PICTURE > Contrast menu and press
/
.
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
0
+30
-30
30
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Color
Highlight the PICTURE > Color menu and press
/
.
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight the PICTURE > Tint menu and press
/
.
The higher the value, the more reddish the picture becomes. The lower the value, the more
greenish the picture becomes.
Adjusting Sharpness
Highlight the PICTURE > Sharpness menu and press
/
.
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Adjusting Brilliant Color
Highlight the PICTURE > Brilliant Color menu and press
/
.
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in the projected picture.
It enables a greater than 50% brightness increase in mid-tone images, which are common in
video and natural scenes, so the projector reproduces images in realistic and true colors. If
you prefer images with that quality, select On. If you don’t need it, select Off.
When Off is selected, the Color Temperature function is not available.
Selecting a Color Temperature
Highlight the PICTURE > Color Temperature menu and press
/
.
The options available for color temperature* settings vary according to the signal type
selected.
1.
T1: With the highest color temperature, T1 makes the image appear the most bluish
white than other settings.
2.
3.
4.
T2: Makes images appear bluish white.
T3: Maintains normal colorings for white.
T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One
of the common methods of representing white color is known as the “color temperature”. A
white color with a low color temperature appears to be reddish white. A white color with a
high color temperature appears to have more blue in it.
Operation
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction, should
you require it.
If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc., you can project any image
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1.
2.
Go to the DISPLAY menu and highlight Color Management.
Press MODE/ENTER on the projector or Enter on the remote control and the Color
Management page is displayed.
3.
4.
Highlight Primary Color and press
Green, Cyan, Blue, or Magenta.
/
to select a color from among Red, Yellow,
Press
to highlight Hue and press
/
to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the
right for how the colors relate to each
other.
Yellow
GREEN
RED
For example, if you select Red and set its
range at 0, only pure red in the projected
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
Cyan
Magenta
5.
Press
to highlight Saturation and adjust
BLUE
its values to your preference by pressing
/
. Every adjustment made will reflect to the
image immediately.
For example, if you select Red and set its value at 0, only the saturation of pure red
will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
6.
Press to highlight Gain and adjust its values to your preference by pressing
/
.
The contrast level of the primary color you select will be affected. Every adjustment
made will reflect to the image immediately.
7.
8.
9.
Make sure you have made all of the desired adjustments.
Press MENU/EXIT on the projector or Exit on the remote control to exit and save the
settings.
32
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Hiding the image
In order to draw the audience's full attention to the
presenter, you can use
on the projector or Blank
on the remote control to hide the screen image. Press
any key on the projector or remote control to restore
the image. The word 'BLANK' appears at the lower
right corner of the screen while the image is hidden.
You can set the blank time in the SYSTEM SETUP:
Basic > Blank Timer menu to let the projector
return the image automatically after a period of time
when there is no action taken on the blank screen.
Once Blank is pressed, the projector enters Economic mode automatically.
CAUTION
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no
I
control keys on the projector will operate except
POWER.
1.
Press
on the projector or go to the
SYSTEM SETUP: Basic > Panel Key
Lock menu, and select On by pressing
on the projector or remote control.
/
2.
A confirmation message is displayed. Select
Yes to confirm.
To release panel key lock, press and hold
seconds on the projector.
for 3
You can also use the remote control to enter the SYSTEM SETUP: Basic > Panel Key
Lock and press to select Off.
/
•
•
Keys on the remote control are still functional when panel key lock is enabled.
I
If you press POWER to turn off the projector without disabling panel key lock, the
projector will still be in locked status the next time it is turned on.
Operation
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Freezing the image
Press Freeze on the remote control to freeze the
image. The word 'FREEZE' will be displayed in the
upper left corner of the screen. To release the
function, press any key on the projector or remote
control.
Even if an image is frozen on the screen, the pictures
are running on the video or other device. If the
connected devices have active audio output, you will
still hear the audio even though the image is frozen on
screen.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500
m–3000 m above sea level, and temperature is between 0°C–35°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature
is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under
such a condition.
To activate the High Altitude Mode:
Notice
1.
Press MENU/EXIT on the projector or MENU
We recommend you use the High Altitude
mode by selecting it whenever your
environment is higher than 1500 m.
on the remote control and then press until
/
the SYSTEM SETUP: Advanced menu is
highlighted.
Do you want to turn High Altitude Mode
ON?
2.
3.
Press
press
to highlight High Altitude Mode and
to select On. A confirmation
No
Yes
/
message is displayed.
Highlight Yes and press MODE/ENTER on the projector or Enter on the remote
control.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude Mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
34
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
Menu Display Time in the SYSTEM SETUP: Advanced > Menu Settings menu sets
the length of time the OSD will remain active after your last key press. The time length
ranges from 5 to 30 seconds in 5-second increments. Use
frame.
/
to select a suitable time
•
•
•
Menu Position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the
OSD position in five locations. Use to select a preferred position.
Language in the SYSTEM SETUP: Basic menu sets your familiar language for the
OSD menus. Use to select your language.
Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be
displayed during projector start-up. Use to select a screen.
/
/
/
Shutting down the projector
I
1.
Press POWER and a confirmation message
is displayed prompting you.
If you don't respond in a few seconds, the
message will disappear.
I
2.
Press
POWER a second time. The
POWER indicator light flashes blue, the
projection lamp shuts down, and the fans will
continue to run for approximately 90 seconds
to cool down the projector.
3.
Disconnect the power cord from the wall
socket if the projector will not be used in an
extended period of time.
CAUTION
•
•
•
•
To protect the lamp, the projector will not respond
to any commands during the cooling process.
To shorten the cooling time, you can also activate
Do not unplug the power cord before the projector shutdown sequence is complete or
during the 90-second cooling down process.
If the projector is not properly shut down, to protect the lamp, when you attempt to re-start
I
the projector, the fans will run for a few minutes to cool down. Press POWER again to
start the projector after the fans stop and the POWER indicator light flashes blue.
Operation
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
The menu items are available when the projector detects at least one valid signal. If there is
no equipment connected to the projector or no signal detected, limited menu items are
accessible.
Main menu
Sub-menu
Options
Off/Whiteboard/Greenboard/
Blackboard
Screen Color
Aspect Ratio
Keystone
Position
Phase
Auto/4:3/16:9
H. Size
1.
Zoom
DISPLAY
3D Sync
3D Sync Invert
TI 3D DLP Link/Off
Disable/Invert
R/G/B/C/M/Y
Primary Color
Hue
Color
Management
Saturation
Gain
PC source: Brightest/Daylight/ViewMatch/
Cinema/User 1/User 2
Video source: Brightest/Gaming/ViewMatch/
Cinema/User 1/User 2
Color Mode
PC source: Brightest/Daylight/ViewMatch/Cinema
Reference Mode Video source: Brightest/Gaming/ViewMatch/
Cinema
2.
Brightness
Contrast
Color
PICTURE
Tint
Sharpness
Brilliant Color
On/Off
Color Temperature
Save Settings
T1/T2/T3/T4
Quick Auto Search
On/Off
3. SOURCE
36
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Language
Front Table/Rear Table/Rear
Ceiling/Front Ceiling
Projector Position
Auto Power Off
4.
Disable/5 min/10 min/20 min/30
min/40 min/50 min/60 min
SYSTEM
SETUP:
Basic
Disable/5 min/10 min/15 min/20
min/25 min/30 min
Blank Timer
Panel Key Lock
Timer Controller
On/Off
Disable/30 min/1 hr/2 hr/3 hr/4
hr/8 hr/12 hr
Splash Screen
Message
Black/Blue/ViewSonic
On/Off
Quick Cooling
High Altitude Mode
DCR
On/Off
On/Off
On/Off
Active VGA Out
On/Off
Mute
Audio Settings Volume
Active Audio Out On/Off
On/Off
Menu Display
Time
5 sec/10 sec/15 sec/20 sec/25
sec/30 sec
5.
Menu Settings
SYSTEM
SETUP:
Advanced
Center/Top-Left/Top-Right/
Bottom-Left/Bottom-Right
Menu Position
Closed Caption
Enable
On/Off
Closed Caption
Caption Version CC1/CC2/CC3/CC4
Lamp Mode Normal/Economic
Lamp Settings Reset Lamp Timer
Equivalent Lamp Hour
Change Password
Security
Settings
Power On Lock
On/Off
On/Off
Reset All Settings
•
•
•
•
•
Source
Color Mode
Resolution
Color System
Equivalent Lamp Hour
6.
Current System Status
INFORMATION
Operation
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of each menu
Function
Description
Corrects the projected picture’s color when the projection surface
Screen Color
Aspect Ratio
Keystone
There are three options to set the image's aspect ratio depending
on your input signal source. See "Selecting the aspect ratio" on
page 27 for details.
Corrects any keystoning of the image. See "Correcting keystone"
on page 26 for details.
Displays the position adjustment page. To move the projected
image, use the directional arrow keys. The values shown on the
lower position of the page change with every key press you made
until they reach their maximum or minimum.
Position
Adjusts the clock phase to reduce image distortion.
Phase
Adjusts the horizontal width of the image.
H. Size
Zoom
Magnifies or reduces the projected image. See "Magnifying and
searching for details" on page 27 for details.
This projector features a 3D function which enables you to enjoy
the 3D movies, videos, and sporting events in a more realistic
way by presenting the depth of the images.
You need to wear a pair of 3D glasses to view the 3D images.
•
TI 3D DLP Link:
Enable projector for TI 3D DLP Link.
3D Sync
•
Off: Disable 3D.
When the 3D Sync function is on:
•
•
•
•
The brightness level of the projected image will decrease.
The Color Mode cannot be adjusted.
The Keystone can only be adjusted within limited degrees.
The Zoom can only magnify the pictures to limited sizes.
3D Sync
Invert
When you discover the inversion of the image depth, enable this
function to correct the problem. (For TI 3D DLP Link only)
Color
Management
38
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Function
Description
Pre-defined picture modes are provided so you can optimize
your projector image set-up to suit your program type. See
"Selecting a picture mode" on page 29 for details.
Color Mode
Selects a picture mode that most suits your need for the image
quality and further fine-tune the image based on the selections
listed on the same page below. See "Setting the User 1/User 2
mode" on page 30 for details.
Reference
Mode
Adjusts the brightness of the image. See "Adjusting Brightness"
on page 30 for details.
Brightness
Contrast
Color
Adjusts the degree of difference between dark and light in the
Adjusts the color saturation level -- the amount of each color in a
Adjusts the red and green color tones of the image. See
"Adjusting Tint" on page 31 for details.
Tint
The function is only available when Video or S-Video with
NTSC system is selected.
Adjusts the image to make it look sharper or softer. See
"Adjusting Sharpness" on page 31 for details.
Sharpness
Adjusts white peaking while maintaining correct color
details.
Brilliant
Color
Color
Temperature
Save
Settings
Saves the settings made for the User 1 or User 2 mode.
Quick Auto
Search
Operation
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Function
Description
Sets the language for the On-Screen Display (OSD) menus. See
"Using the menus" on page 21 for details.
Language
The projector can be installed on a ceiling or behind a screen, or
with one or more mirrors. See "Choosing a location" on page 11
for details.
Projector
Position
Allows the projector to turn off automatically if no input signal
is detected after a set period of time. See "Setting Auto Power
Off" on page 44 for details.
Auto Power
Off
Sets the image blank time when the Blank feature is activated,
once elapsed the image will return to the screen. See "Hiding the
image" on page 33 for details.
Blank Timer
I
Disables or enables all panel key functions except POWER
Panel Key
Lock
on the projector and keys on the remote control. See "Locking
control keys" on page 33 for details.
Timer
Controller
Sets the auto-shutdown timer. The timer can be set to a value
between 30 minutes and 12 hours.
Allows you to select which logo screen will be displayed during
projector start-up. Three options are available: ViewSonic logo,
Black screen, or Blue screen.
Splash
Screen
Selecting On displays the current information on the screen
when the projector is detecting or searching for a signal.
Message
Selecting On enables the function and the projector cooling time
will be shortened to a few seconds.
Quick
If you attempt to restart the projector right after the quick
cooling process, it may not be turned on successfully and
will rerun its cooling fans.
Cooling
High Altitude
Mode
A mode for operation in high altitude areas. See "Operating in a
high altitude environment" on page 34 for details.
Enables or disables the DCR (Dynamic Contrast Ratio) function.
Selecting On enables the function and the projector will
automatically switch the lamp mode between normal and
economic modes according to the input image detected.
DCR
This function is only available when a PC source is in use.
After enabling DCR, frequent lamp mode switching may
shorten lamp life and noise level will vary during operation.
40
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Function
Description
Selecting On outputs a VGA signal when the COMPUTER IN
1/COMPUTER IN 2 and COMPUTER OUT sockets are
correctly connected to devices. See "Connecting a monitor" on
page 14 for how to make the connection.
Active VGA
Out
The sound adjustments made as below will have an effect on the
projector speaker. Be sure you have made a correct connection to
the audio input is connected.
Mute
Mutes the sound.
Audio
Settings
Volume
Adjusts the sound level
Active Audio Out
Selecting On outputs an audio signal when the AUDIO IN and
AUDIO OUT sockets are correctly connected to devices.
Menu Display Time
Sets the length of time the OSD will remain active after your last
key press. The range is from 5 to 30 seconds in 5-second
increments.
Menu
Settings
Menu Position
Sets the On-Screen Display (OSD) menu position.
Closed Caption Enable
Activates the function by selecting On when the selected input
signal carries closed captions.
•
Captions: An on-screen display of the dialogue, narration,
and sound effects of TV programs and videos that are closed
captioned (usually marked as "CC" in TV listings).
Set your screen aspect ratio to 4:3. This function is not
available when the aspect ratio is “16:9”.
Closed
Caption
This function is only available when a Composite video or
S-Video input signal is selected and its system format is
NTSC.
Caption Version
Selects a preferred closed captioning mode. To view captions,
select CC1, CC2, CC3, or CC4 (CC1 displays captions in the
primary language in your area).
Operation
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Function
Description
Lamp Mode
Reset Lamp Timer
Lamp
Settings
Equivalent Lamp Hour
on how the total lamp hour is calculated.
Security
Settings
Returns all settings to the factory preset values.
Reset All
Settings
The following settings will still remain: Phase, H. Size, User
1, User 2, Language, Projector Position, High Altitude
Mode, Security Settings.
Source
Shows the current signal source.
Color Mode
Shows the selected mode in the PICTURE menu.
Current
System
Status
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
42
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
•
•
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
•
•
To remove dirt or dust, wipe the case with a soft, lint-free cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
•
Make sure the temperature and humidity of the storage area are within the
consult your dealer about the range.
•
•
•
Retract the adjuster feet.
Remove the battery from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
Maintenance
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer.
To obtain the lamp hour information:
1.
Press MENU/EXIT on the projector or MENU on the remote control and then press
until the SYSTEM SETUP: Advanced menu is highlighted.
/
2.
Press to highlight Lamp Settings and press MODE/ENTER on the projector or
Enter on the remote control. The Lamp Settings page is displayed.
You will see the Equivalent lamp hour information on the menu.
To leave the menu, press MENU/EXIT on the projector or Exit on the remote
control.
3.
4.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item. To keep the lamp life as long as possible, you
can do the following settings via the OSD menu.
Setting Lamp mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If the
Economic mode is selected, the light output will be reduced and result in darker projected
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > Lamp
mode menu and press
/
.
Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is detected
after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off menu and
press
/
. If the preset time lengths are not suitable for your presentation, select Disable.
The projector will not automatically shut down in a certain time period.
44
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
CAUTION
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator
still lights up after turning the power back on, please contact your dealer. See "Indicators" on
page 49 for details.
The following lamp warning displays will remind you to change the lamp.
Status
Message
The lamp has been in operation for 3500 hours.
Install a new lamp for optimal performance. If the
projector is normally run with Economic selected
44), you may continue to operate the projector
until the 3950 hour lamp warning appears.
Notice
Order Replacement Lamp
Lamp > 3500 Hours
OK
The lamp has been in operation for 3950 hours. A
new lamp should be fitted to avoid the
inconvenience when the projector runs out of lamp
time.
Notice
Replace Lamp Soon
Lamp > 3950 Hours
OK
The lamp has been in operation for 4000 hours.
Notice
It is strongly recommended that you replace the
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished. If the lamp is not
replaced beforehand, it must be replaced after
4000 hours usage.
Replace Lamp Now
Lamp > 4000 Hours
Lamp usage time exceeded
OK
The lamp MUST be replaced before the projector
will operate normally.
Notice
Lamp usage time exceeded
Replace lamp (refer to User Manual)
Then reset lamp timer
OK
Maintenance
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp
To prepare a new lamp, contact your dealer and tell the lamp type number.
Type number: RLC-055 (PJD5122/PJD5211/PJD5221)
RLC-056 (PJD5231)
WARNING
Hg - Lamp contains mercury. Manage in accordance with local disposal
•
•
•
To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces. Before replacing the
lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp
edges in the lamp compartment. Wash hands after lamp replacement.
•
Only ViewSonic certified lamps are tested with this projector. Use of other lamps may
cause electrical shock and fire.
1.
Turn the power off and disconnect the
projector from the wall socket. If the
lamp is hot, avoid burns by waiting for
approximately 45 minutes until the
lamp has cooled.
2.
3.
Turn the projector over. Then loosen
the screws on the lamp cover.
Remove the lamp cover from the
projector.
WARNING
•
•
Do not turn the power on with the lamp
cover removed.
Do not insert your fingers between the
lamp and the projector. The sharp edges
inside the projector may cause injuries.
4.
Loosen the screw that secures the lamp.
46
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Pull out the lamp connector from a slot
in the lamp compartment. Disconnect it
from the projector as illustrated.
1
2
2
6.
Lift the handle so that it stands up. Use
the handle to slowly pull the lamp out
of the projector.
CAUTION
•
•
•
Pulling it too quickly may cause the lamp
to break and scatter broken glass in the
projector.
Do not place the lamp in locations where
water might splash on it, children can
reach it, or near flammable materials.
Do not insert your hands into the projector
after the lamp is removed. If you touch the
optical components inside, it could cause
color unevenness and distortion of the
projected images.
7.
8.
Insert the new lamp into the lamp
compartment and make sure it fits in
the projector.
Reconnect the lamp connector and
place it back into its slot to be flush
with the projector.
Maintenance
47
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Tighten the screw that secures the lamp.
CAUTION
•
•
Loose screw may cause a bad connection,
which could result in malfunction.
Do not over tighten the screw.
10. Ensure the handle is fully laid flat and
locked in place.
11. Replace the lamp cover on the
projector.
12. Tighten the screws that secure the lamp
cover.
CAUTION
•
•
Loose screw may cause a bad connection,
which could result in malfunction.
Do not over tighten the screws.
13. Restart the projector.
CAUTION
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
14. After the startup logo, open the On-Screen
Display (OSD) menu. Go to the SYSTEM
SETUP: Advanced > Lamp Settings menu.
Press MODE/ENTER on the projector or Enter
on the remote control. The Lamp Settings page
is displayed. Press to highlight Reset lamp
timer and press MODE/ENTER on the projector
or Enter on the remote control. A warning
message is displayed asking if you want to reset
Notice
Reset Lamp Timer?
Cancel
Reset
the lamp timer. Highlight Reset and press MODE/ENTER on the projector or Enter
on the remote control. The lamp time will be reset to '0'.
CAUTION
Do not reset if the lamp is not new or replaced as this could cause damage.
48
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicators
Light
Status & Description
Power Temp Lamp
Power events
Blue
Flashing
Off
Off
Stand-by mode
Powering up
Normal operation
Blue
Off
Off
Off
Off
Blue
1.
The projector needs 90 seconds to cool down as it was
abnormally shut down without the normal cooling
down process. Or
Blue
Flashing
2.
3.
The projector needs to cool for 90 seconds after the
power is turned off. Or
The projector has shut down automatically. If you try to
re-start the projector, it will shut down again. Please
contact your dealer for assistance.
Off
Off
Lamp events
The projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact
your dealer for assistance.
Purple
Flashing
Off
Off
Red
Red
1.
2.
The projector needs 90 seconds to cool down. Or
Please contact your dealer for assistance.
Off
Thermal events
Off
Off
Red
Red
Red
Red
Red
Red
Red
Red
Red
Green
Off
Red
Off
Green
Red
Red
The projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact
your dealer for assistance.
Red
Green
Red
Blue
Blue
Purple
Purple
Off
Green
Red
Green
Red
Maintenance
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
The projector does not turn on.
Cause
Remedy
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
There is no power from the power
cord.
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
No picture
Cause
Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly.
The projector is not correctly
connected to the input signal device.
Check the connection.
Select the correct input signal with the
SOURCE key on the projector or remote
control.
The input signal has not been
correctly selected.
The lens cover is still closed.
Blurred image
Cause
Open the lens cover.
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of the projector if necessary.
The lens cover is still closed.
Open the lens cover.
Remote control does not work
Cause
Remedy
The battery is out of power.
Replace the battery with a new one.
There is an obstacle between the
remote control and the projector.
Remove the obstacle.
You are too far away from the
projector.
Stand within 8 meters (26 feet) of the
projector.
50
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Projector specifications
All specifications are subject to change without notice.
General
Product name
Digital Projector
Optical
Resolution
•
•
PJD5122: 800 x 600 SVGA
PJD5211/PJD5221/PJD5231: 1024 x 768 XGA
Display system
Lens F/Number
Lamp
1-CHIP DMD
F = 2.57 to 2.65, f = 21 to 23.1 mm
•
•
PJD5122/PJD5211/PJD5221: 220 W lamp (RLC-055)
PJD5231: 210 W lamp (RLC-056)
Electrical
Power supply
Power consumption
AC100–240V, 2.9 A, 50/60 Hz (Automatic)
315 W (Max); < 1 W (Standby)
Mechanical
Dimensions
Weight
264 mm (W) x 96.4 mm (H) x 225 mm (D)
2.3 Kg (5.07 lbs)
Input terminal
Computer input
RGB input
D-Sub 15-pin (female) x 2
Video signal input
S-VIDEO
Mini DIN 4-pin port x 1
VIDEO
RCA jack x 1
SD/HDTV signal input
Analog – D-Sub <–> Component RCA jack x 3
(through RGB input)
Output terminal
RGB output
Speaker
D-Sub 15-pin (female) x 1
1 watt (mono) x 1
Control terminal
RS-232 serial control
8 pin x 1
Environmental Requirements
Operating temperature
0°C–40°C at sea level
Operating relative humidity 10%–90% (without condensation)
Operating altitude
•
•
0–1499 m at 0°C–35°C
1500–3000 m at 0°C–30°C (with High Altitude Mode
on)
Specifications
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
264 mm (W) x 96.4 mm (H) x 225 mm (D)
264
225
96.4
60
66
Ceiling mount installation
189
Ceiling mount screws:
M4 x 8 (Max. L = 10 mm)
Unit: mm
Timing chart
Supported timing for PC input
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Frequency
Resolution
Mode
(MHz)
720 x 400
31.469
31.469
37.861
37.5
43.269
24.688
61.91
37.879
48.077
46.875
53.674
30.998
77.425
70.087
59.94
72.809
75
85.008
49.673
119.518
60.317
72.188
75
85.061
49.916
119.854
28.3221
25.175
31.5
31.5
36
19.75
52.5
40
720 x 400_70
VGA_60
VGA_72
VGA_75
VGA_85
640 x 480
VGA_50
VGA_120
SVGA_60
SVGA_72
SVGA_75
SVGA_85
SVGA_50
SVGA_120
50
49.5
56.25
30.75
83
800 x 600
52
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
48.363
56.476
60.023
68.667
39.634
98.958
49.702
62.795
71.554
60
60.004
70.069
75.029
84.997
49.98
119.804
59.81
74.934
84.88
60
65
75
78.75
94.5
52
137.75
83.5
106.5
122.5
108
148.5
106.5
121.75
162
XGA_60
XGA_70
XGA_75
XGA_85
XGA_50
XGA_120
WXGA_60
WXGA_75
WXGA_85
1280 x 960_60
1280 x 960_85
WXGA+_60
SXGA+_60
UXGA
1024 x 768
1280 x 800
1280 x 960
85.938
55.935
65.317
75
85.002
59.887
59.978
60
1440 x 900
1400 x 1050
1600 x 1200
640 x 480@67Hz
832 x 624@75Hz
1024 x 768@75Hz
1152 x 870@75Hz
35
66.667
74.546
75.02
75.06
30.24
57.28
80
MAC13
MAC16
MAC19
MAC21
49.722
60.241
68.68
100
1024 x 768@120Hz is not supported for the PJD5122.
Supported timing for Component-YPbPr input
Signal Format
480i(525i)@60Hz
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
1080P@60HZ
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
67.5
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
60
1080P@50Hz
56.26
50
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image
vibration.
Supported timing for Video and S-Video inputs
Horizontal
Frequency (kHz)
15.73
Vertical Frequency
Color sub-carrier
Frequency (MHz)
Video mode
(Hz)
60
50
NTSC
PAL
3.58
4.43
15.63
SECAM
PAL-M
PAL-N
15.63
15.73
15.63
50
60
50
4.25 or 4.41
3.58
3.58
PAL-60
NTSC4.43
15.73
15.73
60
60
4.43
4.43
Specifications
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright information
Copyright
Copyright 2010. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, ViewSonic Corporation
reserves the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
54
Copyright information
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
IR control table
Key
Power
Freeze
Up
Format
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
Byte1 Byte2 Byte3 Byte4
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
83
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
02
03
0b
0c
0d
0e
10
82
83
08
04
07
0f
fd
fc
f4
Down
f3
Left
f2
Right
f1
Color Mode
Volume+
Volume-
Auto
ef
7d
7c
f7
Source
Blank
fb
f8
Menu
f0
Magnify +
Magnify -
Enter
18
19
15
85
14
41
45
52
09
0a
e7
e6
ea
7a
eb
be
ba
ad
F6
F5
Exit
Mute
VGA1
VGA2
Video
Keystone +
Keystone -
RS232 command table
<Pin assignment for this two end>
Pin
Description
Pin
Description
CTS
1
3
5
7
RX
NC
2
4
6
8
GND
RTS
TX
NC
GND
Appendix
55
Download from Www.Somanuals.com. All Manuals Search And Download.
<Interface>
RS-232 protocol
115200 bps (default)
Baud Rate
Data Length
Parity Check
Stop Bit
8 bit
None
1 bit
Flow Control
None
Function
Status
Write
Action
Turn on
Turn off
CMD
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E
Power
Reset
Power
status (on/
off)
Read
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69
Execute
High
Altitude
Mode Off
Write
Read
High
Altitude
Mode
High
Altitude
Mode On
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C 0x6A
High
Altitude
Mode status
Lamp Mode
Normal
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10 0x6E
Write
Read
Lamp Mode
Economic
Lamp Mode
Lamp Mode
status
Front Table
Rear Table
Rear Ceiling
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60
Write
Projector
Position
Front
Ceiling
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61
Projector
position
status
Read
Write
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F
Off
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F
TI 3D DLP
Link
3D Sync
3D Sync
Status
Read
Write
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20 0x7F
Off
On
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 0x7F
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80
3D Sync
Invert
3D Sync
Invert
Read
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x21 0x80
Status
56
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Contrast
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61
Write
Read
Contrast
increase
Contrast
Contrast
ratio
Brightness
decrease
Write
Read
Brightness
Brightness
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03 0x62
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62
Brightness
Aspect ratio
Auto
Aspect ratio
real
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x01 0x63
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65
Write
Aspect
Ratio
Aspect ratio
4:3
Aspect ratio
16:9
Read
Aspect ratio
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04 0x63
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63
Auto Adjust
Execute
Horizontal
position
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65
shift right
Write
Read
Write
Horizontal
Position
Horizontal
position
shift left
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06 0x65
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65
Horizontal
position
Vertical
position
shift up
Vertical
position
Vertical
Position
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07 0x66
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08 0x67
shift down
read
Vertical
position
Read
Write
Read
color
temperature
T1
color
temperature
T2
color
temperature
T3
Color
temperature
color
temperature
T4
color
temperature
status
Appendix
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Blank on
Blank off
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69
Write
Read
Write
Blank
Blank status
Decrease
Increase
Keystone-
Vertical
Keystone
status
Read
Write
Read
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69
Brightest
Cinema
User 1
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x02 0x6B
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x03 0x6C
User 2
Color Mode
Daylight /
Gaming
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B 0x6A
ViewMatch
Color Mode
status
Primary
color R
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 0x6E
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 0x6F
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x10 0x6F
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F
Primary
color G
Primary
color B
Write
Read
Primary
Color
Primary
color C
Primary
color M
Primary
color Y
Primary
color status
Hue
decrease
Write
Read
Write
Read
Write
Hue
Hue
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11 0x70
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70
Hue
Saturation
decrease
Saturation
Saturation
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71
Saturation
Gain
decrease
Gain
Gain
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72
Read
Write
Gain
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F
Freeze on
Freeze off
Freeze
Freeze
status
Read
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60
58
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Inputsource
VGA
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66
Inputsource
VGA2
Write
Inputsource
Composite
Source
input
Inputsource
S-VIDEO
Read
Write
Source
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62
Quick Auto
Search on
Quick Auto
Search off
Quick Auto
Search
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61
Quick Auto
Search
Read
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02 0x62
status
Mute on
Mute off
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00 0x61
Write
Read
Mute
Mute status
Increase
Volume
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62
Write
Read
Volume
Decrees
Volume
Volume
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0a 0x6B
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0b 0x6C
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0c 0x6D
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0d 0x6E
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0e 0x6F
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0f 0x70
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71
Write
Language
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x11 0x72
Read
Language
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x00 0x62
Appendix
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Reset Lamp
usage hour
Write
Read
Read
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01 0x63
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D 0x66
Lamp Time
Error status
Lampusage
hour
Read error
status
60
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
T=Telephone
Country/Region
Web Site
E-mail
F=Fax
AUS=1800 880 818
NZ=0800 008 822
Australia/New Zealand
Canada
T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533
F= 1-909-468-3757
Europe
T= 852 3102 2900
Hong Kong
India
T= 1800 11 9999
Ireland (Eire)
Korea
T= 080 333 2131
T= 0800-4441185
T=1230-020-7975
T= 01800-9-157235
T= 001-8882328722
Latin America (Argentina)
Latin America (Chile)
Latin America (Columbia)
Latin America (Mexico)
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Merida, Yucatan. Tel: 01.999.925.19.16
Latin America (Peru)
Macau
ap.viewsonic.com/me/
T= 0800-54565
T= 853 2870 0303
Contact your reseller
Middle East
T= 1-800-688-6688 (English)
T= 1-866-379-1304 (Spanish)
F= 1-909-468-3757
Puerto Rico & Virgin Islands
Singapore/Malaysia/Thailand
South Africa
ap.viewsonic.com/za/
T= 65 6461 6044
Contact your reseller
United Kingdom
United States
T (Toll-Free)= 1-800-688-6688
T (Toll)= 1-424-233-2530
F= 1-909-468-3757
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
®
VIEWSONIC PROJECTOR
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South America: Three (3) years
warranty for all parts excluding the lamp, three (3) years for labor, and one (1) year for the original lamp
from the date of the first consumer purchase; Europe except Poland: Three (3) years warranty for all parts
excluding the lamp, three (3) years for labor, and ninety (90) days for the original lamp from the date of
the first consumer purchase; Poland: Two (2) years warranty for all parts excluding the lamp, two (2) years
for labor, and ninety (90) days for the original lamp from the date of the first consumer purchase.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than four (4) hours average daily
usage, North and South America: One (1) year warranty for all parts excluding the lamp, one (1) year for
labor, and ninety (90) days for the original lamp from the date of the first consumer purchase; Europe:
One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for
the original lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic office for the
warranty information.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s
installed lamp only. All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration, failure, or malfunction resulting from:
a. Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature, improper
maintenance, unauthorized product modification, or failure to follow instructions supplied
with the product.
b. Operation outside of product specifications.
c. Operation of the product for other than the normal intended use or not under normal conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
g. Causes external to the product, such as electric power fluctuations or failure.
Download from Www.Somanuals.com. All Manuals Search And Download.
h. Use of supplies or parts not meeting ViewSonic’s specifications.
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support
(please refer to “Customer Support” page). You will need to provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name,
(c) your address, (d) a description of the problem, and (e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service
center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
including the implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience,
loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill,
interference with business relationships, or other commercial loss, even if advised of the possibility
of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion of
incidental or consequential damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada,
contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is
subject to the terms and conditions of the Maintenance Guarantee Card.
com under Support/Warranty Information.
4.3: Projector Warranty
PRJ_LW01 Rev. 1h 06-25-07
Download from Www.Somanuals.com. All Manuals Search And Download.
Mexico Limited Warranty
®
VIEWSONIC PROJECTOR
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the
warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic
will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include
remanufactured or refurbished parts or components & accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of the first consumer purchase.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification,
unauthorized attempted repair, or failure to follow instructions supplied with the product.
b. Any damage of the product due to shipment.
c. Causes external to the product, such as electrical power fluctuations or failure.
d. Use of supplies or parts not meeting ViewSonic’s specifications.
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is
displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the
attached Customer Support page). You will need to provide your product’s serial number, so please record the product
information in the space provided below on your purchase for your future use. Please retain your receipt of proof of
purchase to support your warranty claim.
For Your Records
Product Name: ________________________
Document Number: ____________________
Purchase Date: ________________________
Model Number: __________________________
Serial Number: ___________________________
Extended Warranty Purchase? _______________(Y/N)
If so, what date does warranty expire? _________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c)
your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the
implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of
the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business
relationships, or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Villahermosa:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: [email protected]
Puebla, Pue. (Matriz):
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: [email protected]
Veracruz, Ver.:
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: [email protected]
Chihuahua
Tel: 01-22-91-00-31-67
E-Mail: [email protected]
Cuernavaca
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: [email protected]
Distrito Federal:
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: [email protected]
Guadalajara, Jal.:
QPLUS, S.A. de C.V.
SERVICRECE, S.A. de C.V.
Av. Coyoacán 931
Av. Niños Héroes # 2281
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : [email protected]
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: [email protected]
Monterrey:
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: [email protected]
Oaxaca, Oax.:
MERIDA:
ELECTROSER
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: [email protected]
Fax: 01(52)95-15-13-67-00
E-Mail. [email protected]
FOR USA SUPPORT:
Tijuana:
STD
ViewSonic Corporation
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
381 Brea Canyon Road, Walnut, CA. 91789 USA
Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
Fax: 1-800-685-7276
4.3: ViewSonic Mexico Limited Warranty
PRJ_LW03 Rev. 1A 06-25-07
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|