15"/17"/19"TFT-LCD monitor
USER MANUAL
V152/V174/V192
Important Safety Instructions
1. Read the manual carefully before using the monitor.
2. Save these user manual for later use.
3. Unplug the monitor from the power source when you clean the monitor. Don't use liquid
cleaners or aerosol cleaners.Use cloth to clean it. If it doesn't do, please use LCD screen
cleaners.
4. Don't use attachment not recommended as they may cause hazards.
5. Please grasp the plug to unplug the connector from the wall outlet. Don't pull the power cord
to unplug it.
6. Don't place anything on the power cord or step on it.
7. Don't place the monitor near water source such as bathtub, washbowl, sink, laundry tub,
swimming pool etc.
8. The slots are designed for ventilation, simultaneously to keep the machinery workable and
protect it from overheating. For the same reason,please do not place the monitor on the bed,
sofa,carpets or other similar surface. Don't place the monitor near or over heat source or
place in built-in installation.
9. Keep 5 cm away from the wall or other goods.
10.This monitor can only use the power source indicated on the label. If you have questions,
please consult your dealer.
11.As safety measure, this monitor is equipped with a three-wire ground style plug.If you can't
insert the plug into outlet, contact your electrician to replace your outlet. Don't defeat the
safety purpose of the grounding-type plug.
1
12. Please make sure that the outlet and power cord can afford the total electricity of the
products.
13. Place the monitor in safe place where the cord will not be abused by persons working on it.
14. Follow all the warnings and instructions illustrated on the manual.
15. Don't overload the wall outlets and extend cords as this can result in fire or electric shocks.
16. Don't remove or open the cover to service this monitor yourself. It may expose you to
dangerous voltage or other hazards before all servicing to qualified service personnel.
17.Unplug this monitor from the outlet and refer servicing to qualified service personnel under
the following conditions.
● The power cord is frayed or damaged.
● The monitor has been dropped or the cabinet has been damaged.
● When the monitor displays a distinct change in performance ,this indicates a need for
service.
18. The power cord is the main device to disconnect the power.
19. Unplug the power cord when you do not use it for a long time..
20. Place the monitor in good ventilation and protect it from strong light,overheating and damp
environment
℃
21. This monitor must be stored in temperature -20℃～55 .Otherwise,it may cause permanent
damage.
2
1. Introduction
1.1 General Information
This monitor is a high-performance intelligent multi-scanning color monitor .It is with TFT LCD screen
and MCU digital control without radiation and glary. The shape is tiny and thin adapting to small places,save
your more place.
1.2 Features
Color:16.7M
Power saving compliant with EPA energy star and VESA DPMS.
Auto color balance .When connected to different graphic adapter,the monitor can calibrates the white and
black reference voltage.
Plug & play,compatiable with Windows9X&ME&NT&2000&XP and VESA DDC1/2B.
1.3 Check the list
Please make sure that all of the following items are included before operating this monitor.
■
■
■
■
LCD monitor(include base)
AC adapter( optional)
Power cord,VGA signal cable, DVI-D signal cable( optional), audio cable (optional)
User's manual,pass certificate,warranty certification
3
If any of above listed items are missing, please contact your dealer for technical support.
2. Installing the monitor
Please consider the following advice before you install your
monitor.
Position
Choose a place that reflects less to place your monitor.
Generally ,there is a suitable angle with a window.
Highness
The peak of the monitor should be a little lower than your
eyes when you sit down.
VGA cab le
DVI cable
Pow er c ord
(Optional)
Aud io cable
Inclination
You will feel comfortable with the sloping screen.
Fig.1
2.1 Assembly
Take the monitor from the carton, fix base and knighthead
with screw [Fig.1].
● VESA Hanging style
The client may put the monitor on the wall . If you use the style,
you need purchase the hanging subassembly which accords
with VESA standard . Operation as these [ Fig.2]:
(1) Take apart the plastic cover of axis of rotation, screw
three bolts .
(2) Clean up the signal cable , power cord and audio cable.
(3) Fix hanging subassembly on the back cover to hang up
the monitor on the wall.
Fig.2
4
2.2 Signal cable connection
Plug one connector of the signal cable into the VGA or DVI port and lock the two bolts to ensure firm
grounding.Then plug the other one into the monitor and lock the two bolts.
2.3 Power cord connection
Plug one side of the power cord into the AC adapter and the other side into AC power source outlet, then plug
the output side of the AC adapter into the power port at the side of monitor.
2.4 Audio cable connection
Plug one side of the audio cable into the PC audio port, then plug the other side into the audio port of the
monitor.
2.5 Power on
Switch on the power to both the monitor and your computer.After the monitor is power on,the LED lights up
green or blue. If the LED becomes red and flashing, please check the video signal cable connection.If the
LED is off, please press power switch slightly.
2.6 Self test pattern
If there is no horizontal or vertical sync.signal, your monitor will display Fig.3 to Indicate no signal input.After
a few seconds, the monitor will come into waiting and saving power mode;if the monitor receives the video
signal,it will return to the normal mode.
＋
Power
LED Indicator
－
AUTO
Fig.3
Fig.4
5
2.7 Adjust the picture
In order to obtain the best visual display, you need adjust it, please refer to chapter 3 " the Operation of the
monitor ".
3.Operation
OSD control panel
Fig.4 is elevation. Other models differ in key-press position and front panel.
3.1 Power on/off switch
This is a slight touch digital control key. It is used to turn the monitor on or off.
3.2 Power LED indicator
When the monitor is working, the power LED is green or blue. If the monitor is in saving power mode,
the power LED will be red and flashing . If you turn off the monitor, the power LED will be off. When the
LED is off , the monitor is off, but the power adapter is on. For security, you should turn off power adpater
while you don't use the monitor.
3.3 OSD control keys
3.3.1 Auto key
This key is used to complete auto- adjusting function ,it make the monitor to be the best visual
display status in VGA mode. This key is used to switch VGA and DVI signal in DVI mode.
3.3.2 +/- key
These two keys can complete the navigate right or left and choose the control of the menu function.
The adjustment value can be set directly by +/- key.
3.3.3
key
Confirmation key can show the menu and complete the confirmation function.
6
3.4 OSD menu
3.4.1 The meaning of the menu in VGA mode [as Fig.5]:
1. auto adjustment 2. brightness 3. contrast
4. H-position 5. V-postion 6. clock
7. phase 8. signal source 9. color adjustment
10. volume (optional) 11. sharpness
12. OSD position/transparence 13. recall
14. language 15. exit 16. selected function name
17. resolution 18. H-frequency 19. V-frequency
20. progressive bar of adjustment
S
CONTRAST
1024X768 H：48.0KHZ V：60.0HZ
21. percentage of adjustment
22. customer LOGO
23. OSD display time
Fig. 5（DVI MODEL）
CONTRAST
1024X768 H：48.0KHZ V：60.0HZ
Fig. 5（VGA MODEL）
7
3.4.2 The meaning of the menu in DVI mode [as Fig.6]
1. brightness 2. contrast 3.sharpness
4. volume(optional) 5.OSD menu display time
6. transparence 7.OSD position
9300
8. signal source 9. 9300k 10. 7800k
7800
6500
USER
11. 6500k
12. User 13. Recall 14. Language
BRIG HTN ESS
15. Eixt 16.selected function name
17. resolution 18. H-frequency 19. V-frequency
20. progressive bar of adjustment
21. precentage of adjustment
1024X768 H：48.3KHZ V：60.0HZ
22. customer LOGO
Fig.6
Fig.7
Fig.8
8
3.4.3 Function table
Display contents
Function
Auto adjustment
Brightness
Automatically adjust to obtain the best setting
Adjust the brightness
Adjust the contrast
Contrast
Move the screen toward left or right
Move the screen toward upward or downward
Adjust the frequency of pixel
Adjust the phase of pixel clock
Adjust the sharpness of the picture
Adjust the colors of the picture
Set 9300K color temperature
Set 7800K color temperature
Set 6500K color temperature
Set user mode
H-position
V-position
Clock
Phase
Sharpness
Color
9300K
7800K
6500K
9300
7800
6500
USER User mode
Auto color balance
Auto color balance
Adjust the volume
W- B
Volume
Adjust the OSD display time
Adjust the parameter of OSD
Move the menu toward left or right
OSD display time
OSD adjustment
OSD H-position
OSD V-position
Move the menu toward upward or downward
OSD transparency
Signal source
Recall
Setting OSD transparency
Exchange signal mode between VGA and DVI
Reset factory setting
Language
Language selection
Exit
Exit the menu
9
3.4.24 Special function
1. Color adjustment(
): when the function is selected, the
monitor will come into the sub-menu [ Fig.7 ], there are
five functions that can be selected: a,9300k; b,7800k;
c,6500k;d,USER;e,W-B.Selecting USER,you will enter
user mode and you can make adjustment to R/G/B values
to obtain your satisfying color;Selecting W-B,it will enter
color balance mode,and the monitor will automatically
adjust the white-black color reference voltage to obtain
optimal color balance.
OSD H-POSITION
30%
Fig.9 VGA
R
G
B
2. R/G/B adjustment(
monitor will automatically enter R/G/B adjustment mode,push
" key,the relative options will flash, then adjust it by "+/- "
key. Then push " " key again to exit.
3.Language( ).
): In "USER" mode, the
OSD H-POSITION
"
30%
There are six languages to select[Fig.8]
ENG.: English
FRE.: French
DEU.: German
Fig.10 DVI
ITA.: Italian
ESP.: Spanish
PYC.: Russian(TUR.:Turkish or POR.: Portuguese)
4.Position of OSD menu(
of OSD menu and transparence [as Fig.9:VGA
): When you select the item, you can adjust H-position and V-position
Fig10:DVI].
、
.
10
5.Sharpness adjustment(
): Adjust the sharpness of the picture on the screen.
3.5 Safety mode
When the video signal exceeds the frequency range of the monitor , the monitor MCU will stop
horizontal and vertical scanning in order to protect the monitor. Fig.11 will be display on the screen .
After a few seconds, the monitor will enter turn-off mode. You need restart the computer and
reset the frequency range.
OUT OF RANGE
OUT OF RANGE
W ORK IN G F REQUE NCY RA NGE
HF:30K H z-80K Hz
VF :55Hz -75Hz
M a x.Res :1280X1 024
WO R KING FREQUENC Y R AN GE
HF:3 0KH z-6 0KH z
VF:55H z-75 H z
Ma x.R es: 12 80 X76 8
CUR RENT M OD E:
HF:9 4. 0K Hz
VF:84.9Hz
CU R R EN T MOD E:
HF:69.0KHz
VF:85H z
Fig.11(V152)
Fig.11(B V174/V192)
3.6 Timing guide
V152
Polarity
H-Frequency
H:31.468KHz
V:70.0Hz
NO.
Mode
Resolution
Bandwidth
H: －
28.322MHz
720X400
1
2
3
4
5
6
V: －
H: －
VGA
H:31.469KHz
V:60.0Hz
H:37.879KHz
V:60.3Hz
H:48.363KHz
V:60.0Hz
640X480
800X600
1024X768
1024X768
1024X768
25.175MHz
40.0MHz
65MHz
V: －
H: ＋
SVGA
XGA
V: ＋
H: －
V: －
H: －
H:56.476KHz
V:70.0Hz
H:60.023KHz
V:75.0Hz
75MHz
V: －
H: ＋
V: ＋
78.75MHz
11
Recommended mode: 1024×768@60Hz
V174/V192
NO .
Mode
VGA
Resolution
Ver.frequency
Hor.frequency
Pixel clock
1
2
3
4
5
60Hz
72Hz
75Hz
60Hz
25.175MHz
31.5MHz
31.5MHz
40MHz
31.5KHz
37.9KHz
37.5KHz
37.9KHz
640×480
48.1KHz
46.9KHz
48.4KHz
56.5KHz
60KHz
SVGA
800×600
72Hz
75Hz
60Hz
70Hz
75Hz
75Hz
60Hz
60Hz
75Hz
50MHz
6
7
49.5MHz
65MHz
1024×768
8
75MHz
9
1024×768
1152×864
1280×960
78.75MHz
108MHz
105MHz
108MHz
135MHz
XGA
10
11
12
13
67.5KHz
60KHz
64KHz
SXGA
1280×1024
80KHz
Recommended mode: 1280X1024@60Hz
12
3.7 Plug & Play
This monitor meets the standard of VESA DDC. When using video card with VESA DDC1/2B,it will auto-scan
video frequency, output power, function and other data to PC when computer is on .It will go to proper conn-
ection mode and proper resolution frequency.
3. 8 Power management
This monitor complies with EPA energy star requirement and meets VESA DPMS standard.
The following is the description of the power indicator for the power saving mode [Fig. 12].
MODE
Power indicator
Power consumption
V174
V152
V192
On
Green or blue
Red flashing
Off
＜30W
＜40W
＜45W
Stand by/suspend
Off
＜5W
＜3W
＜5W
＜3W
＜5W
＜3W
(include power adapter＇s consumption)
Fig.12
3.9 Volume adjust
Adjust the volume by OSD menu and software of the PC.
4. Specification
Monitor type
TFT LCD
Model
V152
V192
V174
Surface disposal
Anti glary
Anti glary
Anti glary
Active area
304.128mm ×228.096mm
337.920mm ×270.336mm 376.32mm×301.056mm
Viewable angle：
H
°
°
°
-80 °/＋80
°
-80°/＋80
-75 °/＋75
-70°/＋70
-80 °/＋80
-70°/＋70
°
°
V
MAX. Brightness
MAX. contrast
Response time tr /tf
250cd/m2
400:1
300cd/m2
500:1
250cd/m2
600:1
4/12ms
4/12ms
2/10ms
13
V152
Model
V174
V192
Max. resolution
Input resistance
1024×768@75Hz
1280×1024@75Hz
1280×1024@75Hz
Ω
Ω
Ω
75±3 ％
75±3 ％
75±3 ％
H-frequency
V-frequency
30KHz～60KHz
30KHz～81KHz
30KHz～81KHz
55Hz～75Hz
55Hz～75Hz
55Hz～75Hz
Power supply for Adapter
Power supply for monitor
Rated voltage and MAX.Consumption
Input connector
100V-240VAC 60Hz/50Hz 100V-240VAC 60Hz/50Hz
100V-240VAC 60Hz/50Hz
12VDC 4.2A
12VDC 3.3A
12VDC 4.2A
12VDC 40W
12VDC 30W
12VDC 45W
15 pins D-Sub or DVI-D
pins D-Sub or DVI-D(optional) pins D-Sub or DVI-D(optional)
Power saving control
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Comply with EPA energy star standards
Comply with European CE
Plug & Play
Yes
Yes
Yes
Yes
Environment
86kpa～104kpa
5℃～40℃
Atmosphere pressure
Operating temperature
86kpa～104kpa
5℃～40℃
86kpa～104kpa
5℃～40℃
20%～80%
20%～80%
20%～80%
Humidity
Storage temperature
－20℃～55℃
－20℃～55℃
－20℃～55℃
Dimension(L×W×H)
Unpacking
Packing
360×150×350mm3
418×165×395mm3
393×150×390mm3
455×165×440mm3
430×150×420mm3
490×165×465mm3
Weight
Net weight
Gross weight
3.5kg
5.0kg
5.0kg
7.0kg
6.0kg
8.0kg
14
Note： This specification is subject to change without notices.
5. Dead Pixel Policy
Dead pixels on the TFT LCD panel are sometimes inevitable. ViewEra guarantees that the monitor will be replaced if
the number of dead pixels on our monitor is more than 5 pixels. No dead pixel warranty may be provided during the pr-
omotion period.
6. Warranty & Customer Service
Warranty
ViewEra warrants the monitor for one year on parts, labor and the LCD panel from the date of purchase. For detail
Customer Service
Contact your ViewEra retailer or ViewEra for after sale service.
You may contact ViewEra Customer Service for technical support or RMA as below:
1.By Mail: 328 Paseo Tesoro, Walnut, CA 91789
2. By Telephone: (909)595-3624
3. By Fax: (909)595-3526
The business hours are 9:00 am 6:00 pm PST, Mon Fri.
7. Windows setup
For the best view, please set the monitor type in Windows.
Please select as following:
Control Panel > Monitor > Setting > Advance > Monitor > Change > Show all List ...> Stand >
For 1280 X1024, please set to “SXGA 1280 X1024@75Hz”
15
For 1024X768, please set to “ XGA 1024 X 768 @75Hz”
8. Trouble Shooting
1) Power on but no picture
→Make sure the VGA cable is tightly connected from the video output connector on the video card to the video input connector
on the monitor.
→ Make sure you are using the standard power adapter coming with the monitor.
→ Check your video card if the driver is correctly installed. If there is no video signal from the video card, “O INPUT SIGNAL”
will show on the screen.
2) Wrong or abnormal colors
→ If any color (red, green, or blue) is missing, check video cable to make sure it is securely connected. Loose pins in the cable
connector can cause a bad connection.
3) The text and icon look blurry
16
→ LCD monitor has a native resolution which pixels are produced by cells in fixed pos itions. When a resolution different from the native
resolution is chosen, the LCD monitor uses various interpolation methods to achieve the pseudo resolution. To achieve the optimu-
m viewing quality, choose the native resolution of the panel is recommended.
→ Use “Auto Tuning” function to adjust image quality on the OSD menu or you can hold button 2 for 3 seconds to do auto tuning.
4) Display position is incorrect
→ Use “Auto Tuning” function to adjust image position on the OSD menu or you can hold button 2 for 3 seconds to do auto tuning.
5) Speakers have no sound
→ Make sure the audio cable is tightly connected from the audio output jack on the PC to the audio input jack on the monitor.
6) Residue image
→ If an image remains on the screen for an extended period of time, it may be imprinted in the screen and leave a residue image. It is
characteristic of liquid crystal and is not malfunction or deterioration of the liquid crystal. The residue image will disappear after a
period of time. It is recommended to set up the screen saver for your LCD monitor.
7) Out of Rang
→ The first thing you need to check is the screen resolution. Usually “ut of Range” is caused by improper resolution s etting. You can
recover the proper screen resolution as the following steps for Windows: (Assumed that the optimal resolution and fr equency setting
is 1280x1024@ 60Hz.)
Boot the computer into VGA Mode (F8) [repeatedly] at startup.
Go to “Control Panel” double click on “Display”, click on the SETTINGS TAB, and click on the ADVANCED button.
Then Click on the Adapter TAB, click “List All Modes” and change the screen resolution to 1280x1024. (You can
select 16 bit or 32 bit color which depends on your video card capability.)
Select “1280 by 1024, High Color (16 bit), Default Refresh”
Click on“OK”and“APPLY”.
After clicking “APPLY” button, a message will be displayed “our desktop has been reconfigured. Do you want to
keep these settings”
Click “Yes” and “OK”. Then click “OK” on the Display Properties window.
Restart your PC
After you restart, go back to “List All Modes”to adjus t your screen refresh rate to 60 Hertz.
The “Out of Range” may happen if you switch monitor A to monitor B for your PC. Whenever you change the monitor for your PC,
your PC may detect it as a new hardware and automatically install a proper driver for the monitor. So, you will have both monitor A
and monitor B drivers on your PC. Sometimes the two monitor drivers may conflict each other and cause “Out of Range”. You can
resolve “ut of Range”by uninstalling both monitor drivers and reboot your PC. The Windows will automatically detect the new
hardware and install a proper driver for the monitor. Here is a quick way to uninstall the monitor drivers:
Right click on “My Computer”, select “Properties” and click on“Hardware”. Click on“Device Manager”, select “Monitor”
and click on “+” in front of “Monitor”. Then you can see one of the monitor drivers called “Plug and Play Monitor”. A quick way
is to uninstall all the monitor drivers and then let Windows automatically detect the new hardware. (Right click on the monitor driver
and select “Uninstall”). Restart your PC.
17
|