Refrigeration at its best
Blast Chiller Operator’s Manual
Reach-In Models: VBC-35, VBC-70, VBC-75 & VBC-100
Roll-In Models: VBC-175, VBC-220, VBC-350,VBC-480 & VBC-660
Manual Part No. 50850502
Rev: 00
Print Date: 11/5/04
1 1 0 Wo o d c r e s t Ro a d , C h e r r y Hill, NJ 0 8 0 0 3
E-Mail: parts@victory-refrig.com
●
●
PART OF AGA FOODSERVICE GROUP
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
(Continental USA Only)
The Seller warrants to the original purchaser, equipment manufactured by Seller to be free from defects in material and
workmanship for which it is responsible. The Seller's obligation under this warranty shall be limited to replacing or
repairing at Seller's option, without charge, F.O.B. Sellers factory, any part found to be defective and any labor and
material expense incurred by Seller in repairing or replacing such part, such warranty to be limited to a period of one
year from date of purchase or thirteen months from date of shipment from Seller's factory, whichever is earlier, provided
terms of payment have been fully met. All labor shall be performed during regular working hours. Overtime premium
charges will be at Buyer's expense.
Proof of purchase must be supplied to Seller to validate warranty. This warranty is valid only if equipment is properly
installed, started-up and inspected by the dealer or authorized Victory Service agent.
Removal or alteration of the serial/data plate from any equipment shall be deemed to release Seller from all warranty
obligations or any other obligations, expressed or implied.
This warranty does not cover Thermostat or Defrost Timer calibration and/or adjustment, freight damage, normal
maintenance items outlined in Owner's Manual, adjustment of door mechanisms or replacement of light bulbs, fuses
or batteries.
Any repairs or replacement of defective parts shall be performed by Seller's authorized service personnel. Seller shall
not be responsible for any costs incurred if the work is performed by other than Seller's authorized service personnel.
Reimbursement claims for part(s) or labor service costs must be made in writing. Model, cabinet serial numbers and
installation location must be shown on the claim. A receipted bill from the servicing agency must accompany the claim,
together with full details of the service problems, diagnosis and work performed. Victory reserves sole discretion
whether further documentation on a claim is to be submitted.
Seller shall not be liable for consequential damages of any kind which occur during the course of installation of
equipment, or which result from the use or misuse by Buyer, its employees or others of the equipment supplied
hereunder, and Buyer's sole and exclusive remedy against Seller for any breach of the foregoing warranty or otherwise
shall be for the repair or replacement of the equipment or parts thereof affected by such breach.
The foregoing warranty shall be valid and binding upon Seller if and only if Buyer loads, operates and maintains the
equipment supplied hereunder in accordance with the instruction manual provided to Buyer. Seller does not guarantee
the process of manufacture by Buyer or the quality of product to be produced by the equipment supplied hereunder
and Seller shall not be liable for any prospective or lost product or profits of Buyer.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED
WARRANTIES WHATSOEVER. SPECIFICALLY THERE ARE NO IMPLIED WARRANTIES OF MERCHANTABILITY
OR OF FITNESS FOR A PARTICULAR PURPOSE.
The foregoing shall be Seller's sole and exclusive obligation and Buyer's sole and exclusive remedy for any action,
whether in breach of contract or negligence. In no event shall Seller be liable for a sum in excess of the purchase price
of the item.
You may register online at www.victory-refrig.com, fax this completed page to (856) 428-7299, or copy and mail form below to Victory.
*NOTE: The following mail-in form or online registration must be filled out and forwarded to Victory by the installer or customer within 10 days
after start-up. Failure to do this will invalidate the warranties. Retain this information for your records.
Cabinet Model No.______________________
110 WOODCREST ROAD
CHERRY HILL, NJ 08003-3648
Cabinet Serial No._________________
TEL: (856) 428-4200
●
FAX: (856) 428-7299
(Data plate information located inside cooler on
the upper left wall)
WARRANTIES NOT VALID UNLESS REGISTERED AT
FACTORY WITHIN 10 DAYS AFTER START-UP DATE.
ORIGINAL DATE OF INSTALLATION __________________________________________________________________
INSTALLATION COMPANY NAME ____________________________________________________________________
STREET_______________________________ CITY_____________________ STATE______ ZIP CODE___________
DISTRIBUTOR’S NAME_____________________________________________________________________________
STREET_______________________________ CITY_____________________ STATE______ ZIP CODE___________
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Page 2
Receiving Shipment
Unpacking
Installation
Electrical Supply
Start-Up
●
Main Control Breakers
●
Initial Start-Up Error Code & Checks
Page 3
Page 4
Page 5
Principals of Operation
Loading and Packing
Food Storage Time
Operation of Blast Chillers
Operation of Blast Chillers (continued)
Defrost
Roll In Blast Chillers with Storage Pod
The Controls
The Controls (continued)
Programming A Blast Chill Cycle
Alarm and Warning Levels
Page 6
Page 7
Alarm and Warning Levels (continued)
The Printer
Printer Set Up
Logger Paper Installation
Print Cartridge Removal & Installation
Page 8
Page 9
Power Failure
Maintenance
●
●
●
Cleaning
Door Gasket
Condenser Cleaning
Technical Service & Replacement Parts
Rules of Thumb
Page 10
Before Calling Service Guide (for Common Problems)
Pages 11-27
Pages 28-40
Parts Lists
Wiring Diagrams
Download from Www.Somanuals.com. All Manuals Search And Download.
Proper installation is the first step to operation. We recommend that your refrigerator or
freezer be installed by an authorized Victory Certified Installer.
RECEIVING SHIPMENT
All units are performance tested and thoroughly inspected prior to shipment. Upon leaving the factory,
all units are in perfect condition. Upon receipt, examine the exterior of the shipment packaging for any
signs of rough handling. If the cabinet is damaged, it should be noted on the delivery slip or bill of
lading and signed. A claim must be filed immediately against the carrier indicating the extent and
estimated cost of damage incurred.
UNPACKING
Remove all external and interior packing and accessories. Ensure all packaging is disposed of
safely.
INSTALLATION
The cabinet should stand level to ensure correct operation of self closing doors and proper drainage
of condensate from the evaporator.
Models fitted with casters are non-adjustable, therefore a level platform/floor should be provided where
the cabinet is to be located. On models fitted with adjustable legs leveling may be achieved by
adjustment of the bottom section of the legs. For marine specification models with flanged feet for
deck fixing and bulkhead fixings, installation should be carried out by a specialist marine company.
For top mounted refrigeration systems please ensure there is 20” [500mm] between the top of the
cabinet and ceiling for service technician access and ventilation.
If the cabinet has been laid on its back or tipped, DO NOT switch on immediately. Leave the cabinet
in the upright position for at least 12 hours before switching on.
ELECTRICAL SUPPLY
Wiring should be done by a qualified electrician in accordance with local electrical codes. All models,
with the exception of the VBC-100 and all Roll-In VBC’s, come fitted with a NEMA plug for safety and
must be grounded. We recommend that if the plug or cable fail, contact Victory’s parts department for
a replacement part.
The VBC-100 and Roll-In VBC’s are 3-phase and requires connection to a suitable supply.
START-UP
MAIN CONTROL BREAKERS
Should the equipment fail to run on initial connection, please check that all Main Control Breakers
(MCBs) are in the "ON" position at the back of cabinet. (*Note: The "ON" position is confirmed by
red indicators on the MCBs.)
INITIAL START-UP ERROR CODES & CHECKS
An “a7” error code (indicating a loss of power) with an audible alarm sound off will always occur
✗
during an initial start-up of a blast chill cabinet. Press the "CANCEL" button (red with symbol), the
error code and audible alarm will discontinue.
A “Battery Failure Configuration Suspect” error message ticket will always print during an initial
start-up. Do not be alarmed when the error message prints; it is only indicating that the back-up
batteries that hold the cabinets data during a power failure is not fully charged. Full battery charge
should be within 24 hours after start-up.
Check the time and date on the printed tickets. If the ticket has printed an incorrect time and date or
the printer logger paper is not feeding properly, see page 7 for further instruction.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINCIPLES OF OPERATION
Victory blast chillers have been designed to quickly reduce the temperature of food in accordance with
Department of Health guidelines on the chilling of cooked foods. All operators should be conversant
with Department of Health publication, Chilled and Frozen Guidelines on Cook-Chill and Cook-Freeze
Catering Systems.
Fast temperature reduction is not brought about by placing the food in a very cold cabinet like a deep
freeze. This would only dry the food badly and take a very long time to reduce its temperature to the
required level. The secret of fast temperature reduction is in delivering the correct blast of air and
ensuring correct and unobstructed horizontal air flow inside the cabinet.
This is why Victory has the option of soft and hard facility on blast chill.
Exceptions: depending on the density types and sizes of the portions the chiller might not be
capable of achieving the required guidelines, therefore, the load and/or depth of the food layers
should be reduced. You may find it necessary to experiment with different amounts of food
and loading methods in order to achieve the optimum performance with your blast chiller.
LOADING AND PACKING
Regulations state that product should be placed in the Blast Chiller within 30 minutes from completion
of cooking. The packaging of food and the way in which it is loaded or placed within the apparatus can
have a significant effect on the time within which the temperature can be reduced to the required level
and the amount of food which can be processed in each chilling batch.
When blast chilling always use metal or foil containers which are good conductors. Plastic or
polyurethane containers insulate the food from the cold air. When chilling unportioned food we
recommend the use of the appropriate pan that is at least 2-1/2” [63.5mm] in depth. Likewise, placing
lids or covers on food will also increase the chilling time but may be of some use when processing
some delicate foods to avoid dehydration.
Always load your machine in such a way that it is possible for the cold air to contact all sides of the
containers. Avoid stacking containers directly on top of one another as this will drastically extend the
chilling time and take special care not to block the air ducts.
Always load the machine before selecting the blast cycle. Unless it is unavoidable do not open the
door of the machine while the blast cycle is engaged.
In the case of roll-in rack models, bumper bars are fitted to the walls inside the machine. This assists
in the correct positioning of the rack(s) so as to avoid blocking the air flow.
FOOD STORAGE TIME
Chilled foods can be stored for up to 5 days at between 32°F/0°C and 38°F/+3°C.
OPERATION OF BLAST CHILLERS
Your machine has been set-up at the factory and no further adjustments should be necessary.
Note: The control systems employed are micro-processor based and contain no user
serviceable components. Instructions on setting up the control panel thermostats are available
from the manufacturer. These should only be reset by a qualified service technician.
Normal Storage:
This is the storage temperature at which food can be held and the Blast Chiller automatically switches
into this mode at the end of each cycle.
Storage Mode
On some chillers there is more than one fan installed these may not all operate during the storage
mode giving a reduced air circulation within the chiller. All other models have one or more Aerofoil
fans. The unit cycles on the store thermostat, the sensor of which is placed in the air.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Blast Chill Cycle:
All machines have the facility for the operator to use any of the 4 pre-programmed timed cycles and a
probe control blast chilling cycle, with the option of soft or hard blast.
The probe controlled blast cycle functions via the food core probe supplied. The probe monitors the
core temperature of the food and will not permit the blast cycle to stop until the default temperature
(37°F\3°C) is reached. When controlling the cycle with the food probe make certain that the probe or
probes are located in the product before the blast cycle is started.
Pressing the selections automatically adopt the previous settings on the first push. So the repeating
of blast is just pushing buttons 1- 2- 3 & Blast .
Blast Chill Cycle (Hard or Soft):
During the blast chill hard cycle the air temperature inside the cabinet should go down to
approximately 14°F (-10°C). This is for the timed chilling cycle only. During soft chill cycle the air
temperature stays above 32°F (0°C ).
All blast chillers have 3 basic modes:
1. Normal storage:
34°F (1°C) to 37°F (3°C)
2. Blast Chill Hard: 14°F (-10°C)
3. Blast Chill Soft:
34°F (1°C)
DEFROST
At the end of each cycle, a defrost will automatically clear any ice from the evaporator ready for the
next cycle.
During the operation in storage mode a defrost will be performed automatically at the factory preset
intervals of 6 hours.
Furthermore, if a blast cycle is cancelled and the defrost thermostat is measuring 34°F (+1°C) or less,
the machine will automatically proceed to defrost.
When the machine is in the defrost mode the ‘Cabinet Temp’ window of the control panel will display
‘DEF’. When the defrost cycle is finished the compressor will run for approximately 90 seconds before
the fans cut in.
Following every defrost period there is a 3 minute period during which a blast cycle cannot be selected.
This short interval is to allow defrost water to drip away from the evaporator.
The cabinet is now ready to start another cycle if desired. During the defrost operation it is safe to
leave products inside the machine.
ROLL- IN BLAST CHILLERS WITH STORAGE POD
On roll-in chillers fitted with storage refrigeration pods, the roll-in blast chiller will function as a small
cold storage room when the chiller is in store mode. A defrost will occur every six hours for 20 minutes.
When the blast facility is engaged, the storage pod will be disengaged and the main compressor and
main evaporator fan will take over until the end of the blast cycle. Immediately following the blast
cycle, a main defrost period will occur. When the defrost period is complete the main compressor will
start up again, followed 1-2 minutes later by the main evaporator fan for a period of 10 minutes. After
10 minutes the blast chiller will revert to storage mode until the blast facility is once more engaged.
THE CONTROLS
The control panel enables the display of detailed information about the machine and its performance.
If the machine is also fitted with a printer (standard on roll in machines, optional on reach in cabinets),
detailed historical information can be printed out for immediate use or archived.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. The ‘Cabinet Temp’ display window can be used:
❖ To show the cabinet wall temperature.
❖ As a count up timer in probe blast.
2. The ‘Probe’ window can show:
❖ Temperature during a blast cycle, (blank during store).
❖ During a blast if a food probe fails it will display ‘pf’ in its own window. At the end of a blast
cycle it will indicate alarm code in Probe 1 window.
3. For a timed blast, the green row of LEDs show the progress of the blast. Each LED indicates
another 1/10 of the total blast time has started. When there is only approximately 50 seconds left
to blast, the right hand LED will flash. For a probed blast, the green LEDs again show the blast
progress, but this time each LED indicates 1/10 of the temperature excursion between the products
starting temperature and the target end temperature. Cabinet temperature window also acts as a
count up timer showing in minutes the duration of the probed blast.
PROGRAMMING A BLAST CHILL CYCLE:
1. Switch on the chiller at least half an hour before use.
2. Check that the chiller is operating at storage temperature.
3. Load the products to be chilled (see notes on loading).
4. By pressing button ‘1’ select the ‘Chill’ mode.
5. By pressing button ‘2’ select the desired type of blast, hard or soft.
6. By pressing button ‘3’ select the timer for the desired duration, or probed blast.
✓
7. When you are content with your selected program press the
to start the blast cycle.
✗
8. If you are not content with your selection press the button to cancel your 1/2/3 selection.
✓
✗
As each selection is made, the indicator LED will illuminate to show what is chosen. Press to accept, or to
cancel.
On completion of a cycle, there will be an audible alarm which will cancel automatically after 15 minutes or may
✗
be cancelled with the button. ‘DEF’ will then be displayed in the ‘Cabinet Temp’ window of the control panel
and the chiller will then revert to a store mode appropriate to the blast just completed.
During the defrost operation the temperature in the chiller will not exceed 38°F (+3°C) and it is therefore safe
to leave products in the chiller during the defrost cycle.
To save time for repeated identical blast operations, the blast selections are remembered, so when 1 2 3 are
pressed the selections automatically adopt the previous settings on the first push. So the repeat a blast, just
✓
push 1 2 3
.
ALARM AND WARNING LEVELS
For the following alarm and warning conditions, an audible alarm will be activated and a warning ticket
will be printed if the printer is fitted. A faulty sensor alarm will be initiated if a sensor fault condition is
detected. If there is an alarm condition, probe 1 window will display an alarm number a0 to a7 during
store (*see alarm table at the top of the next page), but will show the probe temperature during blast.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
7-SEG DISPLAY
ALARM CONDITION
Air on sensor failure
Wall sensor failure
Fin sensor failure
Food probe 1 failure
Food probe 2 failure
Food probe 3 failure
Spare
a0
a1
a2
a3
a4
a5
a6
a7
Power cut detected
Note: If a wall sensor fails it will also read -50.
For each probe only one audible alarm and alarm printout is allowed to be issued each day. This is
to prevent excessive paper use and noise nuisance in the event of an intermittent probe failure.
However, repeated probe failures are displayed on the probe display window, (top window in the case
of 3 probe panels).
To cancel the audible alarm press the ✗ button. If the alarm condition still exists the display will
continue to indicate there is a fault.
THERE IS NO RE-SET FACILITY.
THE PRINTER
If fitted and “ON”, the printer is activated after each blast cycle. The printer provides hard copy
historical data of cabinet performance or warning tickets to archive or act upon.
The formats available are:
Midnight Ticket (if programmed)
At midnight a ticket is automatically printed for archiving in the morning. The midnight ticket provides
the following information:
❖ Time and date of printout and cabinet number
❖ Cabinet temperature at time of printout
❖ A graph of cabinet temperature over the preceding 24 hours
Demand Ticket
A ticket may be requested from the control panel by holding the printer ‘On/Off’ button for 5 seconds.
This ticket provides the same information as the midnight ticket except that up to seven days of
historical data are printed.
Alarm or Warning Ticket
A ticket is automatically printed if any condition is detected by the micro controller which may need
attention.
The print function may be terminated by pressing the printer ‘On/Off’ button.
Mains Power Failure Ticket
If mains power fails for more than 5 seconds a ticket is automatically printed which gives the time of
power failure and the time at which power is restored.
Sensor Failure Ticket
If the controller detects that one of its sensors has failed then a warning ticket will be printed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTER SET UP
(CAUTION!!! : DO NOT CHANGE any other parameters when setting the date & time! If additional
parameters are changed, there is a great possibility that the VBC Cabinet will not function properly
and will void warranty!)
TIME AND DATE SET UP
A. Enter the Engineering Switch Mode by doing the following:
1. Turn control panel "off" by pressing the "standby" button.
2. Press and hold the "1" button.
3. While continuing to hold the "1" button, press and release "standby" button.
B. Press the “2” or "3" button to step through the engineering settings. When the display shows
"ute", you have reached the time and date settings.
*Note: The setting functions (i.e. "ute","hr") are only displayed when the "3" button is depressed.
When the button is released, the actual setting value will appear and can then be set.
✔
✖
●
●
●
●
●
Minute (shown as "ute") ➨ Press " " to increase or " " decrease minute
✔
✖
Hour (shown as "hr") ➨ Press " " to increase or " " decrease hour
✔
✖
Day (shown as "day") ➨ Press " " to increase or " " decrease day
✔
✖
Month (shown as "nth") ➨ Press " " to increase or " " decrease month
✔
✖
Year (shown as "yr") ➨ Press " " to increase or " " decrease year
*Note: When entering the year, there could be only one character displayed. Examples are below:
1 = the year 2001
2 = the year 2002
3 = the year 2003, etc.
C. When entry is complete, press "standby" once to exit the Engineering Switch Mode. Then press
"standby" again to turn on the cabinet.
D. Print demand ticket by holding printer "on/off" button for five (5) seconds. A printout will be
produced to confirm new information entered.
*Special Note: If there is information entered by error, wait approximately two (2) minutes before
starting the process over.
LOGGER PAPER INSTALLATION
Logger paper should be installed as shown. It is best to tear the end
of a new roll at a 90 degree angle for easy installation.
Once logger paper roll has been inserted into the printer, use the
“feed” button on the control panel to automatically bring paper forward.
PRINT CARTRIDGE REMOVAL & INSTALLATION
“Paper Installation”
●
●
●
Remove printer cover and logger paper.
Press the end of print cartridge that calls out "PUSH" & "EJECT".
Once cartridge is pressed at "PUSH" & "EJECT" end, simply
remove cartridge from the printer.
●
Place new cartridge by carefully putting at designated location.Turn
*Note: (1) If printer does not work, check the print cartridge and logger paper for
proper installation. (2) Exposed print cartridge ribbon can dry out. Adjust to printable
fresh ink by turning the wheel in the direction indicated by the arrow. Change out
print cartridge with the spare provided if adjusting the ribbon does not work. (3) All
blast chillers are shipped with a spare print cartridge and logger paper. Print cartridges
and logger paper can be purchased from a local office supply store.
“Print Cartridge Removed”
7
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER FAILURE
A power cut does not cause the loss of any accumulated historical data and no re-programming is
necessary. The controller’s battery is continually charged and provides emergency back up under
normal power failure conditions.
MAINTENANCE
The cabinets are fully automatic in operation. Cleaning, loading printer paper, and changing out the
print cartridge is the only maintenance required. Read the following topics.
CLEANING
Exterior: The exterior of the cabinet is stainless steel and if cared for correctly will keep its ‘as new’
finish for many years. Normal day to day cleaning should be carried out with a soft cloth and soapy
water. Always wipe the cabinet vertically in the same direction as the grain
in the stainless steel. Whilst stainless steel is a very strong and robust
material, the stain smooth finish can be spoiled by wiping against the grain.
Never use abrasive materials or cleaners, or chemical cleaners, as they can
damage the surface and cause corrosion. Occasionally, the exterior should
be polished with a good stainless steel polish to protect the surface.
Do not use abrasive cleaners, chemicals or scouring pads on the control
panel. Clean the control panel only with a soft damp cloth. Avoid excess
water on the control panel, and other areas where electrical components are
fitted.
Interior: The racking can be removed for easy cleaning (see Fig 1). This
should be done on a regular basis with warm water and a soft cloth, dry
thoroughly afterwards. To remove the racking and shelf supports follow this
procedure: First remove the shelves, then remove the shelf supports by
grasping firmly in the center and lifting slightly. Turn the shelf support towards
the interior of the cabinet by pushing it in the center as you twist the support
through 90°. The shelf support will be released. (Note: the supports are
designed to be anti-tilt and you may therefore experience some resistance at
first which will be overcome with practice). When all shelves have been
removed, remove the racking by lifting up and over the nylon retaining blocks.
Fig 1
Retainer Channel
Door Gasket
Clean the gasket weekly with warm soapy water and a soft cloth taking care
not to damage it. DO NOT use a sharp knife to clean or scrape the gasket.
Regularly check the gasket for any damage. Damage can be caused by
striking the gasket with a sharp object such as the corner of a tray. Damaged
gaskets do not seal correctly and can increase the amount of electricity
consumed, seriously affecting the efficiency and performance of the cabinet.
Damaged gaskets are easily replaced. To fit a new gasket - simply pull out the
old gasket and push the new gasket into the channel (gasket retainer) at the
center and work along the gasket pushing it into the channel, continue in the
same way on the other three sides, pushing the corners in last (see Fig 2).
Gasket
Fig 2
Condenser Cleaning
The condenser, which is part of the refrigeration unit, is sited in the unit compartment and requires
cleaning, approximately 4 times per year or when the LED indicates. To clean the condenser,
disconnect main power supply before starting, then brush the fins vertically with a stiff brush,
taking care not to damage the fins or push dirt or dust further in and vacuum away. Remember to
reconnect main power supply once finished.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SERVICE & REPLACEMENT PARTS
Victory Refrigeration strives to provide excellent customer service along with quality equipment. To
help us better assist you, a serial number and/or model number must be provided when contacting the
technical service or parts department. The data plate is located inside the reach-in cabinet on the right
side wall. Roll-in blast chiller data plates are placed on the exterior of the back panel that supports the
controller. All serial numbers are recorded and kept indefinitely.
RULES OF THUMB
❒
❒
❒
❒
❒
Pre-chill the cabinet for thirty (30) minutes before you do first load (to remove interior residual heat).
Doubling the food thickness triples the pull-down time.
Don’t stack food and/or containers on top or alongside of each other.
Covering the food increases pull-down time by 10% - 30%.
Pull-down rate initially is about 2°F per minute and approaching final temperature is about 2
minutes per degree Fahrenheit.
❒
Factors affecting blast chill pull-down times:
1. Entering food temperatures (the hotter the initial temperature, the longer the pull-down time).
2. Final food temperature (the colder the final temperature, the longer the pull-down time).
3. Food “thickness” (the greater the distance from geometric “core” center of food to it’s surface
pull-down time).
4. Food density (the greater the density, the longer the pull-down time).
5. Food thermal conductivity (the lower the conductivity, the longer the pull-down time).
6. Food specific heats (the higher the specific heat, the longer the pull-down time).
7. Container surface area (the smaller the surface area, the longer the pull-down time).
8. Container material (metals are conductors and render a shorter pull-down than plastics which
are insulators).
9. Covering material (metal preferred instead of plastic for reasons above).
10. Covering method-cover such as aluminum foil or a “stretch wrap film” placed in direct
contact with food eliminates the “dead air space” between the cover and the food. Since
“dead air space” is an insulator, elimination of reduction of it shortens pull-down time.
11. “Delta T” is temperature difference between the food and the blast of air. The greater the
“Delta T” the quicker the pull-down time.
12. Air velocity (the greater the air velocity across the food, the faster the pull-down time).
13. Amount (weight) of food put in as compared to rated capacity of machine. Exceeding the
capacity increases the pull-down time.
14. Mechanical problems (equipment not operating at full efficiency takes longer to pull down)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC PARTS LISTS
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST FOR VICTORY BLAST CHILLER 35 (VBC-35)
Item No
Description
Part No.
1
Comp CAJ 4492Y R134A
52000101
52000201
52000301
52000401
52000501
1a
1b
1c
2
Coil Condenser 3 x 11 x 21
Drier 1/4 x 3/16 Sweat R134A
Sight Glass 1/4 Sweat
Receiver 2.2L
3
3
3
4
4
5
Valve Expansion Body Ten 2 R134A
Valve Adapter Solder 1/4
Orifice No. 00 068-2090
Motor Condenser Fan 16 Watt
Blade Cond Fan 10In 27Dg Pitch
Plate Condenser Fan
52000601
52000701
52000801
52000901
52001001
52001101
6
7
8
Motor Evap Fan 315mm Axial
Guard Evap Fan Wire 50mm Deep
Plate Evaporator Fan
52001201
52001301
52001401
9
Upright Pilaster Racking
52001501
52001603
52001701
52001801
52001901
52002001
52002101
52002201
10
Probe Food 90 Degree Heavy Duty
Probe Socket Type T Flanged
Cover Unit Front Top Section
Cover Unit Front Bottom Section
Gasket Door 26-3/4 x 16-15/16
Plate Hinge R7 Opal Top
10a
11
11a
12
13
14
Hinge Door Spring Loaded
15
16
17
18
19
20
21
22
23
23
23
23
24
Door Standard VBC35
Coil Evaporator 4 x 13 x 17
Tray Drip
52002301
52002401
52002501
52002601
52002701
52002801
52002901
52003001
52003101
52003201
52003301
52003401
52003501
Heater Defrost 300W 3 Bend
Plug Nylon Door Hinge Top
Insert Nylon Pilaster Ladderack
Screw 6mm x 12 Pozi Pan Zinc
Label Polypanel W/O Printer
Panel Front No Printer 1Probe (123)
Board Back WBC II (123)
Logger Chip Full WBC II
Cable Ribbon Front To Back 1M
Leg, S/S 4IN Short Stud C/C Plate
25
26
27
Contactor 190V 50Hz/220V 60Hz
Screw 6mm x 25mm Zinc Pozi Pan
Slide Pan (Tray) S/S 276mm
52003601
52003701
52003801
28
29
30
31
32
33
34
35
36
*
Clip Latch Unit Cover Front
Clip Strike Unit Cover Front
Screw Set 8mm x 20mm Zinc
Cover Rear
Vaporizer Hot Gas
Plug 15 Amp 3 Pin
Cord Power Cable 3 Wire 14AWG
Insert Nylon Plstr Mtg Ladderack
Hinge Cabinet Piece
Klixon 14T31 30210 L13C 9651
Switch Thermal Heated 331-528
52003901
52004001
52004101
52004201
52004301
52004401
52004501
52004601
52004701
52004801
52004901
*
*
*
*
*
Heater Wire 3M 240V 30 Watts
Bracket Fan Motor
Caster W/O Brake
52005001
52005101
52005201
52005301
Caster W/ Brake
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST FOR VICTORY BLAST CHILLER 70 (VBC-70)
Item No
Description
Part No.
1
2
CONDENSING UNIT CAJ 4511Y HR
52077901
52078001
52078101
52078201
52000601
52010901
52071701
52004801
52078301
52078401
52002201
52078501
52078601
52078701
52005201
52011701
52003701
52011401
52003201
52044601
52003301
52010801
52011501
52001603
52004901
52010701
52078801
52078901
52079001
52004401
52004501
52014301
52014302
52079101
52002801
52079201
52079301
52079401
52079501
52079601
52079701
EVAPORATOR FAN 16 WATT 208V 60Hz UL
DEFROST HEATER 300W 1BEND
EVAPORATOR 3" x 20" x 20"
EXPANSION VALVE BODY TEN2 R134A
3/8" SOLDER ADAPTOR 068-2060
ORIFICE NO.2 068-2096
KLIXON 14T31 30210 L13C 9651
GASKET, 22" x 24" [560mm X 622mm]
PLUG, TOP HINGE
3
4
5
5
5
6
7
7a
8
8a
8b
8c
9
9a
9b
0
10
10
10
11
12
13
14
15
16
16
17
18
18a
19
19
20
20a
21
22
23
24
25
26
HINGE:SPRING LOADED
SCREW 8 X 1/2 POZI PAN ZINC S/T
HINGE PLATE:R4 FLAT
HINGE PLATE:R7 CHROME
CASTERS:NEW 6" UNBRAKED
CASTERS:NEW 6" BRAKED
SCREW M6 X 25 POZI PAN ZINC T/T
AARDWARE FRONT PANEL C/W PRINTER 3 PROBE
AARDWARE BACKBOARD (*ATTACHED BEHIND FRONT PANEL)
MAIN CONTROL BOARD WITH CONTACTORS
LOGGER CHIP FULL (*180 VERSION 11)
DRIER 3/8", R134a
LABEL,BLAST CHILLER 3 PROBE WITH PRINTER
90° ANGLED FOOD PROBE
SWITCH THERMAL HEATED 331-528
SIGHT GLASS, 3/8" SWEAT
LP SWITCH, TYPE G60 T01
HP SWITCH, TYPE G63 T01
1/4" SCHRAEDER VALVE
PLUG 3 PIN USA 15 AMP
CABLE FOR USA LEAD 3 CORE 14AWG/2MM
VAPORIZER HEATER, 115W 3 BEND
VAPORIZER HEATER, 150W 3 BEND
LADDERACK BLOCKS TYPE 1
LADDERACK BLOCKS TYPE 2
EVAPORATOR FAN PLATE
DRIP TRAY
VAPORIZER TRAY
DOOR ASSEMBLY, COMPLETE
UNIT COVER
RACKING, LEFT OR RIGHT SIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST FOR VICTORY BLAST CHILLER 75 (VBC-75)
Item No
Description
Part No.
1
2
Comp 1-1/2 FH4518Y 208/60
Coil Condenser 4 x 17 x 17.5
52020101
52010201
52010301
52010401
52020201
52020301
52010701
52010801
52020401
52010901
52011001
52020501
52020601
52011301
52004801
52001603
52001701
52011401
52003201
52003301
52003401
52011501
52011601
52002701
52002201
52004901
52011701
52011801
52011901
52002801
52020701
52020801
52020901
52021001
52021101
52021201
52021301
52021401
52021501
52012901
52013001
52013101
52003701
52013201
52013301
52013401
52013501
52013601
52013701
52000501
52013801
52021701
52021801
52021901
52022001
52014301
52022101
3
3
3
4
5
6
7
7
Motor Evap Fan (4) 200mm Axial
Guard Evap Fan Flat
Capacitor 230V 60Hz 1.5UF
Coil Evaporator 5 x 45 x 16
Sight Glass 3/8 Sweat
Drier 3/8 Suitable For R134A
Valve Expansion Body Tes 2 R134A
Adapter Solder 3/8 068-2060
Valve Orifice No. 3
Heater Defrost 500W 1 Bend
Panel Control Cover Rear
Heater Wire 4.35 M 240V (57W)
Thermostat, Klixon
Probe Food 90 Degree Heavy Duty
Probe Socket Type T Flanged
Panel Front C/W Printer (123)
Board Back WBC II
7
8
9
10
11
12
13
14
14
14
14
14a
15
16
17
18
19
19a
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
36
37
38
39
40
41
42
43
44
45
46
46
Logger Chip Full
Cable Ribbon Front To Back IM
Polypanel W/ Printer
Control Pressure High/Low
Nylon Plug Door Hinge (Top)
Hinge, Spring Loaded Door
Switch, Thermal Heated 331-528
Caster 6" W/ Brake
Caster 6" W/O Brake
Plate Hinge L3 Opal/T2U Bottom
Insert Nylon Pilaster Ladderack
Cover Unit
Panel Control
Door Standard VBC75
Gasket 53-5/16 x 24-11/16
Upright Pilaster Ladderack
Tray Drip
Plate Baffle
Plate Evaporator Fan
Plate Evaporator Baffle
Plate Condenser Fan
Insert Door M4/T38 6x26
Screw M6x25 Pozi Countersunk
Screw 6mm x 25mm Zinc Pozi Pan
Vaporizer, Electric
Motor Condenser Fan 120 Watt
Capacitor 230V 60Hz 3.0UF
Panel Control Bottom
Cover Hinge Black Plastic
Contactor 190V 50Hz/220V 60Hz
Receiver 2.2L
Insert Nylon 316-F2/St38 M5X5
Cowl Condenser Fan
Slide Pan (Tray)
Control Panel Rear Cover
Thermocouple Type 'T' PTFE 2M
Vaporizer Heater 115W 3 Bend
Box Elec For Comp 833 TFH4524Z
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST FOR VICTORY BLAST CHILLER 100 (VBC-100)
Item No
Description
Part No.
1
2
Comp 2HP TFH 4524 Z 208/60/3
52020101
52010201
52010301
52010401
52020201
52020301
52010701
52010801
52020401
52010901
52011001
52020501
52020601
52011301
52004801
52001603
52001701
52011401
52003201
52003301
52003401
52011501
52011601
52002701
52002201
52004901
52011701
52011801
52011901
52002801
52020701
52020801
52020901
52021001
52021101
52021201
52021301
52021401
52021501
52012901
52013001
52013101
52003701
52013201
52013301
52013401
52021601
52013601
52013701
52021701
52013801
52021801
52021901
52022001
52022101
52022201
52014301
Coil Condenser 4 x 17 x 17.5
Motor Evap Fan (4) 200mm Axial
Guard Evap Fan Flat
3
3
3
4
5
6
7
7
Capacitor 230V 60Hz 1.5UF
Coil Evaporator 5 x 45 x 16
Sight Glass 3/8 Sweat
Drier 3/8 Suitable For R134A
Valve Expansion Body Tes 2 R404A
Solder Adapter 3/8 068-2060
Orifice No. 3
Heater Defrost 500W 1 Bend
Shelf Garnet White Coated
Heater Wire 4.35 M 240V (57W)
Thermostat, Klixon
Probe Food 90 Degree Heavy Duty
Probe Socket Type T Flanged
Front Panel C/W Printer (123)
Board Back WBC II
7
8
9
10
11
12
13
14
14
14
14
14a
15
16
17
18
19
19a
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
36
37
38
39
40
41
42
43
44
45
46
46
Logger Chip Full
Cable Ribbon Front To Back IM
Polypanel W/ Printer
Control Pressure High/Low
Nylon Plug Door Hinge (Top)
Hinge, Spring Loaded Door
Switch, Thermal Heated 331-528
Caster 6" W/ Brake
Caster 6" W/O Brake
Plate Hinge L3 Opal/T2U Bottom
Insert Nylon Pilaster Ladderack
Cover Unit
Panel Control
Door Standard VBC75
Gasket 53-5/16 x 24-11/16
Upright Pilaster Ladderack
Tray Drip
Plate Baffle
Plate Evaporator Fan
Baffle Plate Evaporator
Plate Condenser Fan
Insert Door M4/T38 6x26
Screw M6x25 Pozi Countersunk
Screw 6mm x 25mm Zinc Pozi Pan
Vaporizer Electric
Motor Condenser Fan 120 Watt
Capacitor 230V 60Hz 3.0UF
Panel Control Bottom
Cover Hinge Black Plastic
Contactor 190V 50Hz/220V 60Hz
Receiver 3.3L
Nylon Insert 316-F2/St38 M5X5
Cowl Condenser Fan
Slide Pan (Tray)
Panel Control Cover Rear
Thermocouple Type 'T' PTFE 2M
Box Elec For Comp 833 TFH4524Z52001241
Vaporizer Heater 115W 3 Bend
Download from Www.Somanuals.com. All Manuals Search And Download.
Victory Blast Chillers 175, 220 & 350 (VBC-175, VBC-220 & VBC-350) Panels Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-175, VBC-220 & VBC-350 Panels Parts List
Item #
Part Description
VBC-175
VBC-220
VBC-350
1
2
Panel Roof, Left
52040101
52040201
52040301
52040401
52040501
52040601
52040701
52040801
52040901
52041001
52041101
52041102
52041201
52041202
52041101
52041102
52041301
52041401
52041501
52040101
52040201
52040301
52040401
52040501
52040601
52040701
52040801
52040901
52041001
52041101
52041102
52041201
52041202
52041101
52041102
52041301
52041401
52041501
52040101
52040201
52040301
52040401
52040501
52040601
52040701
52040801
52040901
52041001
52041101
52041102
52041201
52041202
52041101
52041102
52041301
52041401
52041501
Panel Roof, Right
3
Panel Wall, Left Side
Panel Corner, Left Rear
Panel Wall, Rear
4
5
6
Panel, Coved Corner Right Rear
Panel Corner, Front Left
Door
7
8
9
Jam Corner, Coved
Panel Wall, Right Side
10
11
11a
12
12a
13
13a
14
15
16
Upper End Panel (for Cabinet with “POD” Refrigeration System)
Upper End Panel (for Cabinet without “POD” Refrigeration System)
Grille, Front (for Cabinet with “POD” Refrigeration System)
Grille, Front (for Cabinet without “POD” Refrigeration System)
Upper End Panel (for Cabinet with “POD” Refrigeration System)
Upper End Panel (for Cabinet without “POD” Refrigeration System)
Latch, Door
Hinge, Door
Gasket, Door
Download from Www.Somanuals.com. All Manuals Search And Download.
Victory Blast Chillers 175, 220 & 350 (VBC-175, VBC-220 & VBC-350) Equipment Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-175, VBC-220 & VBC-350 Equipment Parts List
Item#
Part Description
VBC-175
VBC-220
VBC-350
1
2
Bracket, Fan Guard
52041601
52041701
52041801
52041901
52042001
52042101
52042201
52042301
52042401
52042501
52042601
52042701
52042801
52042901
52043001
52043101
52043201
52001603
52011401
52003201
52043301
52043401
52011501
52043501
52043601
52043701
52043801
52043901
52044001
52044101
52044201
52044301
52044401
52044501
52044601
52044701
52044801
52044901
52045001
52045101
52045201
52045301
52045401
52045501
52041601
52050101
52041801
52041901
52042001
52042101
52042201
52042301
52042401
52042501
52042601
52050201
52042801
52042901
50243001
52043101
52043201
52001603
52011401
52003201
52043301
52043401
52011501
52043501
52043601
52043701
52043801
52043901
52044001
52044101
52044201
52044301
52044401
52044501
52044601
52044701
52044801
52044901
52045001
52045101
52045201
52045301
52045401
52045501
52041601
52060101
52041801
52041901
52042001
52042101
52042201
52042301
52042401
52042501
52042601
52060201
52042801
52042901
52043001
52043101
52043201
52001603
52011401
52003201
52043301
52043401
52011501
52043501
52043601
52043701
52043801
52043901
52044001
52044101
52044201
52044301
52044401
52044501
52044601
52044701
52044801
52044901
52045001
52045101
52045201
52045301
52045401
52045501
Plate, Fan
3
Angle, Roof
4
Valve, Solenoid EVR10
Valve, Coil Solenoid 60Hz
Blast Fans, HCGT-355J-MXNC
Switch, Fan Cut-Off ZC-055
Bracket, Frame Support
Frame, WBC R/H
5
6
7
8
9
10
Valve, Expansion (Power)
Valve, Expansion (Body)
Valve, Expansion Orifice
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Coil, Evaporator (Dimensions: 6” x 66” x 19.5”)
Assembly, Drip Tray
Baffle, Drip Tray
Guard, Evaporator
Guard, Fan
Probe, 90 Degree Heavy Duty Food
Panel, Front C/W Print (123)
Board, WBC II Back
Screw, Control Panel
Fascia, Control Panel
Polypanel with Printer
Logger Paper
Cover, Printer
Latch
Striker
26
Switch, Isolator
Bar, Isolator
Handle, Isolator
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Lid, Control Panel
Screw, Control Panel Lid
Contactor, Main Control Panel
Box, Control
Bumper, Cart Side
Bumper, Equipment Side
Plate, Bottom Blanking
Hinge, Fan Plate
Heater, Defrost (300 Watt, 1 Bend)
Grommet, Support
Grommet, Blind
Contactor, Cap and Bushing
Breaker, 30 Amp 2-Pole Circuit
Enclosure, 30 Amp 2-Pole Breaker
Download from Www.Somanuals.com. All Manuals Search And Download.
Victory Blast Chillers 175, 220 & 350 (VBC-175, VBC-220 & VBC-350) Storage “POD” Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-175, VBC-220 & VBC-350 Storage “POD” Parts List
Item#
Part Description
VBC-175
VBC-220 VBC-350
1
2
Tray, Vaporizer
52045601
52045701
52045801
52045901
52046001
52000601
52046101
52046201
52046301
52046401
52046501
52046601
52046701
52046801
52046901
52047001
52047101
52045601
52045701
52045801
52045901
52046001
52000601
52046101
52046201
52046301
52046401
52046501
52046601
52046701
52046801
52046901
52047001
52047101
52045601
52045701
52045801
52045901
52046001
52000601
52046101
52046201
52046301
52046401
52046501
52046601
52046701
52046801
52046901
52047001
52047101
Heater, Vaporizer Tray
Klixon, Vaporizer Heater Tray
2a
3
Unit, Condensing (Model: CAJ4461Y, 60Hz, R-134a)
Coil, Evaporator (Dimensions: 4” x 9” x 10”)
Valve, Expansion (Body) Ten 2 R-134a
Orifice, No. 1 68.2091
Chute, Air
4
5
6
7
Tray, “POD” Evaporator Drip
Motor, “POD” Fan
8
9
Plate, Fan
10
11
12
13
14
15
Bolt, M8 x 65
Lid, “POD”
Gasket, Tape Foam
“POD”
Liner, “POD”
Bushing, Bellmouth
Download from Www.Somanuals.com. All Manuals Search And Download.
Victory Blast Chillers 480 & 660 (VBC-480 & VBC-660) Panels Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-480 & VBC-660 Panels Parts List
Item#
Part Description
VBC-480
VBC-660
1
2
Panel Roof, Left
52070101
52070201
52040301
52070301
52040401
52040501
52040601
52040801
52040901
52041001
52070401
52040701
52070501
52070502
52041201
52041202
52070501
52070502
52041301
52041401
52041501
52070101
52070201
52040301
52070301
52040401
52040501
52040601
52040801
52040901
52041001
52070401
52040701
52070501
52070502
52041201
52041202
52070501
52070502
52041301
52041401
52041501
Panel Roof, Right
3
Panel Wall, Left Side
Panel Wall, Left Side
Panel Corner, Left Rear
Panel Wall, Rear
Panel, Coved Corner Right Rear
Door
Jam Corner, Coved
Panel Wall, Right Side
Panel Wall, Right Side
Panel Corner, Front Left
4
5
6
7
8
9
10
11
12
13
13a
14
14a
15
15a
16
17
18
Upper End Panel (for Cabinet with “POD” Refrigeration System)
Upper End Panel (for Cabinet without “POD” Refrigeration System)
Grille, Front (for Cabinet with “POD” Refrigeration System)
Grille, Front (for Cabinet without “POD” Refrigeration System)
Upper End Panel (for Cabinet with “POD” Refrigeration System)
Upper End Panel (for Cabinet without “POD” Refrigeration System)
Latch, Door
Hinge, Door
Gasket, Door
Download from Www.Somanuals.com. All Manuals Search And Download.
Victory Blast Chillers 480 & 660 (VBC-480 & VBC-660) Equipment Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-480 & VBC-660 Equipment Parts List
Item#
Part Description
VBC-480
VBC-660
1
2
3
4
Coil, Evaporator (Dimensions: 6” x 66” x 19.5”)
52042802
52042201
52042101
52042501
52042601
52042701
52050101
52044901
52042402
52070601
52042001
52041901
52042401
52042301
52070701
52042901
52043001
52042801
52045201
52045301
52001603
52043101
52043201
52070801
52070901
52071001
52011402
52003202
52071101
52071201
52044301
52071301
52043901
52044001
52044101
52043301
52071401
52011502
52043501
52043701
52043801
52071501
52045001
52045101
52045401
52045501
52042802
52042201
52042101
52042501
52042601
52050201
52060101
52044901
52042402
52070601
52042001
52041901
52042401
52042301
52070701
52042901
52043001
50242801
52045201
52045301
52001603
52043101
52043201
52070801
52070901
52071001
52011402
52003202
52071101
52071201
52044301
52071301
52043901
52044001
52044101
52043301
52071401
52011502
52043501
52043701
52043801
52071501
52045001
52045101
52045401
52045501
Switch, Fan Cut-Off ZC-055
Fan, Blast HCGT-355J-MXNC
Valve, Expansion (Power)
Valve, Expansion (Body)
Valve, Expansion Orifice
Plate, Fan
5
6
7
Hinge, Fan Plate
8
Frame, WBC L/H
9
Angle, Roof
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Valve, Coil Solenoid 60Hz
Valve, Solenoid EVR10
Frame, WBC L/H
Bracket, Frame Support
Plate, Bottom Blanking
Assembly, Drip Tray
Baffle, Drip Tray
Coil, Evaporator (Dimensions: 6” x 66” x 19.5”)
Grommet, Blind
Contactor, Cap and Bushing
Probe, 90 Degree Heavy Duty Food
Guard, Evaporator
Guard, Fan
Bracket, Fan Guard
Bumper, Equipment Side
Bumper, Cart Side
Panel, Front C/W Print (123)
Board, WBC II Back
Contactor, Main Control Panel
Box, Control
Screw, Control Panel Lid
Lid, Control Panel
Switch, Isolator
Bar, Isolator
Handle, Isolator
33
34
35
36
37
Screw, Control Panel
Fascia, Control Panel
Polypanel with Printer
Logger Paper
Latch
Striker
38
39
40
41
42
Cover, Printer
Heater, Defrost (300 Watt, 1 Bend)
Grommet, Support
Breaker, 30 Amp 2-Pole
Enclosure, 30 Amp 2-Pole Breaker
Download from Www.Somanuals.com. All Manuals Search And Download.
Victory Blast Chillers 480 & 660 (VBC-480 & VBC-660) Storage “POD” Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-480 & VBC-660 Storage “POD” Parts List
Item#
Part Description
VBC-480
VBC-660
1
2
3
Tray, “POD” Evaporator Drip
52071501
52071601
52000601
52071701
52046401
52071801
52071901
52072001
52072101
52045801
52072201
52046601
52072301
52046801
52072401
52072501
52072601
52071501
52071601
52000601
52071701
52046401
52071801
52071901
52072001
52072101
52045801
52072201
52046601
52072301
52046801
52072401
52072501
52072601
Coil, Evaporator (Dimensions: 4” x 10” x 22”)
Valve, Expansion 068Z3385
Orifice No. 1 68.2092
Motor, “POD” Fan
4
5
6
Plate, Fan
Unit, Condensing (Model: CAJ4492YHR, 60Hz, R-134a)
Drier, 3/8” Sweat
7
Heater, Vaporizer Tray (300 Watt, 3 Bend)
Klixon, Tray Heater
8
9
Tray, Vaporizer
10
11
12
13
14
15
Bolt, M8 x 65
Lid, “POD”
Gasket, Tape Foam
“POD”
Liner, “POD”
Chute, Flush 2 Fan Air
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE CONNECTIONS & THERMOCOUPLES
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-35 (208-230V/60Hz/1Ph)
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-70 (208-230V/60Hz/1Ph)
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-75 (208-230V/60Hz/1Ph)
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-100 (208-230V/60Hz/3Ph)
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-175, 220 & 350 with “POD” Refrigeration System
(208-230V/60Hz/3Ph), Page 1of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-175, 220 & 350 with “POD” Refrigeration System
(208-230V/60Hz/3Ph), Page 2 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-175, 220 & 350 without “POD” Refrigeration System
(208-230V/60Hz/3Ph), Page 1 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-175, 220 & 350 without “POD” Refrigeration System
(208-230V/60Hz/3Ph), Page 2 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-480 & 660 with “POD” Refrigeration System
(208-230V/60Hz/3Ph), Page 1 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-480 & 660 with “POD” Refrigeration System
(208-230V/60Hz/3Ph), Page 2 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-480 & 660 without “POD” Refrigeration System
(208-230V/60Hz/3Ph), Page 1 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
VBC-480 & 660 without “POD” Refrigeration System
(208-230V/60Hz/3Ph), Page 2 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Victory Refrigeration Inc
110 Woodcrest Road
Cherry Hill, NJ 08003-3648
Tel: (856) 428-4200
Fax: (856) 428-7299
E-mail: service@victory-refrig.com
or
Download from Www.Somanuals.com. All Manuals Search And Download.
|
TIC Speaker TFS14 User Manual
Toshiba Flat Panel Television 26AV500U User Manual
Toshiba Laptop U200 ST2091 User Manual
Toshiba Switch ASD TB1 SIM9 User Manual
Trimble Outdoors Satellite TV System AgGPS 252 User Manual
U Line Ice Maker CLR2160SOD User Manual
Universal Remote Control Universal Remote UR5 8400 User Manual
VBrick Systems Network Card V443 User Manual
ViewSonic Digital Photo Frame VFD823 User Manual
Weber Gas Grill 56206 User Manual