INSTALLER / CONSUMER
SAFETY INFORMATION
Please read this manual before
installing and using appliance.
WARNING: If the information in this
manual is not followed exactly, a
fire or explosion may result causing
property damage, personal injury or
loss of life.
UVS27R, UVS27M
Vent Free Gas Heaters
Models: 4030-4049, 4085-4087,
4090-4092
—Do not store or use gasoline or
other flammable vapors and
liquids in the vicinity of this or
any other appliance.
—WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do
not use any phone in your building.
• Immediately call your gas
suppler from a neighbor’s phone. Fol-
low the gas suppler’s instructions.
• If you cannot reach your gas supplier,
call the fire department.
Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
This appliance may be installed in an after
market permanently located manufactured
(mobile) home where not prohibited by lo-
cal codes.
Homeowner’s Installation
and Operating Manual
This appliance is only for use with the type
of gas indicated on the rating plate.
This appliance is not convertible for use
with other gases unless a certified kit is
used.
S
G
N
E
D
*Aftermarket: Completion of sale, not for purpose of
resale, from the manufacturer.
This is an unvented gas-fired heater.
It uses air (Oxygen) from the room
in which it is installed. Provisions for
adequate combustion and
C
E
D
R
E
I
F
I
ventilation air must be provided.
Refer to Page 7.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
20007068 4/07 Rev. 8
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Installation & Operating Instructions
In order to ensure safe and effective installation, this unit
CARBON MONOXIDE POISONING
must be installed only by a qualified agency, individual, firm,
corporation or company that is experienced in the instal-
lation, repair and servicing of this type of appliance and is
familiar with the building codes and installation techniques
appropriate in your area. Contact your hearth products
dealer or local gas supplier for the name of a qualified ser-
vice person.
In the Commonwealth of Massachusetts, all gas fittings and
installation of this heater shall only be done by a licensed
gas fitter or licensed plumber.
IMPORTANT: Read this owner’s manual carefully and
completely before trying to assemble, operate, or ser-
vice this heater. Improper use of this heater can cause
serious injury or death from burns, fire, explosion,
electrical shock, and carbon monoxide poisoning.failure
to follow instructions may result in property damage,
bodily injury or loss of life. This manual contains impor-
tant user information. Keep this manual with the heater
after installation is complete.
MAY LEAD TO DEATH!
Carbon Monoxide Poisoning: Early signs of carbon
monoxide poisoning resemble the flu, with headaches,
dizziness, or nausea. If you have these signs, the heater
may not be working properly. Get fresh air at once! Have
the heater serviced. Some people are more affected by
carbon monoxide than others. These include pregnant
women, people with heart or lung disease or anemia,
those under the influence of alcohol, and those at high
altitudes.
7. DO NOT place clothing or other flammable mate-
rial on or near the appliance.
8. DO NOT obstruct the top grille at all. Doing so will
cause high levels of carbon monoxide that will
lead to death.
9. This heater needs fresh, outside air ventilation to
operate properly. See Fresh Air Requirements on
pages 6 and 7.
10. If heater shuts off, heater may not have enough
fresh air ventilation. Provide more fresh air. If
heater keeps shutting off, refer to Troubleshoot-
ing.
FOR SAFE INSTALLATION AND OPERATION,
PLEASE NOTE THE FOLLOWING:
1. Use only Natural Gas with UVS27RN/MN. Use only
Propane with UVS27RP/MP. Do not use any other
fuels.
2. Install only in accordance with the National Fuel
Gas Code, ANSIZ223.1/NFPA54-latest edition. (Ex-
ception: Do not derate this appliance for altitude.
This appliance has been tested and listed for use
in altitudes up to 10,000 feet.)
3. Use only the installation instructions provided by
the manufacturer for this appliance. Installation
and repair should be done by a qualified installer,
preferably NFI or WETT (Canada) certified. The
appliance should be inspected before use and at
least annually by a professional service person.
More frequent cleaning may be required due to
excessive lint from carpeting, bedding material,
etc. It is imperative that control compartments,
burners and circulating air passageways of the ap-
pliance be kept clean.
11. DO NOT operate this heater
•
where flammable liquids or vapors are used
or stored
•
under dusty conditions.
12. The heater becomes very hot when operating.
Alert children and adults to stay away from hot
surfaces to avoid burns or clothing ignition. The
heater will remain hot for a time after shutdown.
Allow surface to cool before touching.
13. Carefully supervise young children when they are
in the room with the heater.
14. Do not use the heater if any part has been ex-
posed to or under water. Immediately call a quali-
fied service technician to inspect the room heater
and to replace any part of the control system and
any gas control which has been under water.
15. DO NOT operate the heater if any log is broken or
damaged.
16. Turn heater off and let cool before servicing. Only
a qualified service person should service and
repair heater.
17. DO NOT operate this appliance with the safety
screen removed. If the safety screen is removed
from the appliance for service or cleaning, it must
be replaced before operating the heater.
NOTE: If any of the original wire as supplied with the ap-
pliance must be replaced, it must be replaced with a wire
of at least 105°F temperature rating.
4. WARNING: Any change to this heater or its con-
trols can be dangerous. DO NOT make modifica-
tions to any heater or associated parts.
5. DO NOT install this heater in a bedroom or bath-
room.
6. Due to high surface temperatures, DO NOT install
this heater
•
•
in a recreational vehicle,
where curtains, furniture, clothing or other
flammable objects are less than 36 inches from
the front, top or sides of the heater,
in high traffic areas,
•
•
in windy or drafty areas.
3
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Shell Dimensions
Freestanding Stove
9"
(229 mm)
C
L
Valve Inlet
26���"
(680 mm)
Valve Inlet
C
L
3"
(76 mm)
14���"
(368 mm)
25"
(635 mm)
Drawing Not to Scale
15���"
7068
(379 mm)
Fig. 1 UVS27 freestanding shell dimensions.
Hearthmount
5"
(140 mm)
C
L
25���"
(641 mm)
�����"
(416 mm)
26���"
(673 mm)
Drawing Not to Scale
5004
Fig. 2 UVS27 Hearthmount specifications.
4
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Clearance Requirements
A
B
C
D
Minimum Clearances to
Combustible Materials
Maintain clearance, (empty space), between combus-
tible materials and the heater as specified below for the
appropriate firebox shell being installed.
S
Freestanding Stove
E
T
D
U
F
A
B
C
V
G
Z
W
X
H
Y
ST101
ST599a
Mantel
Mantel from
Stove Top
Hearthmount
Ref.
A
B
C
D
E
F
G
H
Shelf Depth
13” (330mm)
11¹⁄₄” (286 mm)
9³⁄₈” (241 mm)
7¹⁄₂” (191 mm)
5³⁄₄” (146 mm)
4” (102 mm)
2¹⁄₄” (57 mm)
1” (25 mm)
Ref.
S
T
U
V
W
X
Y
D
35” (889 mm)
30” (762 mm)
25” (635 mm)
20” (508 mm)
15” (381 mm)
10” (254 mm)
5” (127 mm)
2” (51 mm)
C
A
B
Z
Hearth Requirements
ST102
A: Mantel/Trim*.........................35” (889 mm) / 2” (51 mm)
B: Side Wall/Trim*............................................. 2” (51 mm)
C: Rear Wall ....................................................... 0” (0 mm)
D: Max. Mantel Width ................................... 13” (330 mm)
The Freestanding Stove and Hearthmount Shell must
be installed on rigid flooring. If the appliance is installed
on any combustible surface other than wood flooring,
such as carpet or tile, a metal or wood panel must be
installed to extend the full length and width of the unit.
Alcove Clearances
D
B
B
WARNING
A
• Do not install this heater in a bathroom or bed-
room.
• Installationofthisheatermustconformwithlocal
codes or, in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1 / NFPA54.
• This heater creates warm air currents. These
currents move heat to wall surfaces next to the
heater. Installing the heater next to vinyl or cloth
wall coverings or operating the heater where im-
purities in the air such as tobacco smoke exist,
may discolor walls.
ST103
C
A: Ceiling ...................................................... 35” (889 mm)
B: Side Wall...................................................... 2” (51 mm)
C: Rear Wall ....................................................... 0” (0 mm)
D: Max. Alcove Depth................................... 13” (330 mm)
•
Do not use a blower insert, heat exchanger
insert or other accessory not approved for use
with this heater.
5
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Gas Specifications
High Elevations
Input ratings are shown in BTU per hour and are
certified without deration from elevations up to
4,500 feet (1,370m) above sea level.
Max.
Input
Min.
Input
Gas
Air
Model
Fuel Control BTU/h BTU/h Shutter*
Nuisance outages may occur at altitudes above
4,500 feet (1,370m) if dirt, dust, lint and/or cob-
webs are allowed to accumulate on burner and/
or ODS pilot. Monthly inspection and cleaning
is recommended for altitudes above 4,500 feet
(1,370m)
UVS27RN
Nat
Millivolt 28,000 19,500
Fully
Closed
n/a
Fully
Closed
n/a
UVS27RP
UVS27MN
Prop Millivolt 28,000 19,500
Nat Millivolt 28,000 19,500
UVS27MP Prop Millivolt 28,000 19,500
For elevations above 4,500 feet (1,370m), instal-
lations must be in accordance with the current
ANSI Z223.1/NFPA 54 and/or local codes having
jurisdiction.
*Natural Gas units with Glass & Catalyst installed; air
shutter is fully closed and rotated with bend outside of
burner for less restriction. Propane units have no air
shutter.
Firebox weight / shipping
110 lbs.
WARNING: Improper installation, adjust-
ment, alteration, service or maintenance
can cause injury or property damage. Refer
to this manual for correct installation and
operational procedures. For assistance or
additional information consult a qualified
installer, service agency, or the gas supplier.
Gas Inlet and Manifold Pressures
Natural
5.5” w.c.
LP (Propane)
11” w.c.
Inlet Minimum
Inlet Maximum
Manifold Pressure
14” w.c.
14” w.c.
3.5” w.c. 10” w.c. (MP)
11” w.c. (RP)
Odor During Operation
Neither natural gas nor propane gas give off an odor
when burned. The nature of a vent free combustion
system, however, is such that odors may occasional-
ly be produced during heater operation when impuri-
ties exist in the immediate area. Cleaning solutions,
paint, solvents, cigarette smoke, candles, adhesives,
new carpet or textiles, etc., all can create fumes.
These fumes may mix with combustion air and can
create odor. Such odors will disappear over time,
however the condition can be alleviated by opening a
window or otherwise providing additional ventilation
to the area.
UVS27R & UVS27M Vent-Free
Certified to:
ANSI Z21.11.2b-2004
Unvented Heaters
The installation of your Vermont Castings stove
must conform with local codes, or in the absence of
local codes, with the National Fuel Gas Code ANSI
Z223.1/NFPA 54 - latest edition. (EXCEPTION: Do
not derate this appliance for altitude up to 4,500 feet
(1,370m). Maintain the manifold pressure at 3.5” w.c.
for Natural Gas and 11.0” w.c. for LP Gas.
WARNING:
Failure to keep the primary air opening(s) of the
burner(s) clean may result in sooting and property
damage.
6
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Vent Free Features
Provide For Adequate Ventilation
The UVS27, Models 4030, 4036. 4040, 4046, 4085,
4090, is an unvented gas heating appliance tested and
listed to the ANSI standard Z21.11.2b-2004. This ap-
pliance is specifically configured to burn either Natural
Gas or Propane fuel, as indicated on the metal rating
plate attached to the rear shroud. The UVS27 is not fuel
convertible.
Any space within a home can be classified in the follow-
ing categories:
1) Unusually Tight Construction
2) Confined Space
3) Unconfined Space
First, determine which classification defines the intend-
ed space.
The stove is shipped fully assembled and ready for
installation.
Unusually Tight Construction
You must provide additional fresh air if the space falls
into this classification. Unusually Tight Construction is
defined as construction wherein:
a. walls and ceilings exposed to the outside atmo-
sphere have a continuous water vapor retarder with a
rating of one perm or less with openings gasketed or
sealed and
b. weather stripping has been added on openable win-
dows and doors and
c. caulking or sealants are applied to areas such as
joints around window and door frames, between sole
plates and floors, between wall-ceiling joints, between
wall panels, at penetrations for plumbing, electrical, and
The UVS27M is equipped with an SIT control for
manual use only.
The UVS27R is equipped with a Honeywell control
valve that allows thermostatic control, on/off switch or a
remote switch (not supplied).
Both models incorporate variable regulators that al-
low you to adjust burner heat output between HIGH,
(28,000 BTU), and LOW, (19,500 BTU). See the Opera-
tion Section for details.
The standing pilot incorporates an Oxygen Depletion
System (ODS/pilot) designed to shut off the appliance if
enough fresh air is not available.
gas lines, and at other openings.
Fresh Air Requirements for Combustion
and Ventilation
If your home meets all of the three criteria above, you
must provide supplemental fresh air for the appliance
from outside the home as detailed on page 7, B.
If your home does not meet the above criteria, follow
the procedure below.
WARNING
This heater must have fresh air for proper opera-
tion.Ifnot,poorfuelcombustioncouldresult.Read
the following instructions to insure proper fresh
air for this and other fuel-burning appliances in
your home.
Determine if You Have a Confined
or Unconfined Space
Use the following formula to determine if you have a
confined or unconfined space.
Modern construction standards have resulted in homes
that are highly energy-efficient and that allow little heat
loss. Your home needs to breathe, however, and all
fuel-burning appliances within it require fresh air in
order to function properly and safely. Exhaust fans,
clothes dryers, fireplaces, and other fuel burning appli-
ances all use the air inside the building. If the available
fresh air is insufficient to meet the demands of these
appliances, problems can result.
Space is defined as the room in which you will install
the heater plus any adjoining rooms with doorless pas-
sageways or ventilation grilles between the rooms.
The National Fuel Gas Code ANSIZ223.1/NFPA54
defines a confined space as a space whose volume is
less than 50 cubic feet per 1,000 BTU per hour, (4.8
m3 per kw), of the aggregate input rating of all appli-
ances installed in that space and an unconfined space
as a space whose volume is not less than 50 cubic feet
per 1,000 BTU per hour, (4.8 m3 per kw), of the ag-
gregate input rating of all appliances installed in that
space. Rooms communicating directly with the space
in which the appliances are installed, through openings
not furnished with doors, are considered a part of the
unconfined space.
The UVS27R/M Unvented heater has specific fresh air
requirements. You must determine that these fresh
air requirements will be met within the space where
the appliance will be installed. The following informa-
tion will help you insure that adequate fresh air is avail-
able for the heater to function properly.
1. Determine the volume of space, (length x width x
height). Include adjoining rooms connected by doorless
passageways or ventilating grilles.
7
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Example:
A confined space may be ventilated in two ways:
A) Open up or provide at least two ventilating grilles to
an adjoining unconfined space. Use any of the options
illustrated in Figure 3.
A room that is 18’ x 12’ x 8’ has a volume of 1728
cubic feet, ( length x width x height). An adjoining open
kitchen that is 10’ x 12’ x 8’ has a volume of 960 cubic
feet. An adjoining open dining room is 12’ x 12’ x 8’ with
a volume of 1152 cubic feet. The total space volume is
3840 cubic feet. (1728 + 960 + 1152).
Each of the two grilles must provide an opening of
at least 50 square inches, with all opening dimensions
being at least 3”. One grille must be located within 12”
of the ceiling; the other within 12” of the floor. (If the
total exceeds 100,000 BTU/Hr, additional grilles will be
required.)
2. Divide the volume of space by 50 cubic feet. The
result is the maximum BTU/Hr that the space can sup-
port.
Example:
B) Vent the room directly to the outdoors. (Provide
3840 divided by 50 = 76.8 or 76,800 BTU/Hr.
one square inch of opening for each 4,000 BTU/hr.
3. Add the BTU/Hr ratings of all fuel-burning appliances
installed in the same space, including the following:
If the total BTU/Hr used by the appliances is less than
the maximum BTU/Hr the space is able to support,
the room meets the Unconfined space criteria and no
further ventilation is required.
Gas Water Heater
Gas Fireplace Logs
Vented Gas Heater*
Gas Furnace
Unvented Gas Heater
Other Gas Appliances*
For further information on ventilation guidelines and
sizing specifications follow the National Fuel Gas Code
NFPA 54/ANSI Z223.1 Section 5.3.
* Do not include Direct Vent appliances as these
utilize outside air for combustion and vent to the
outdoors.
Example:
W A R N I N G
Gas Range
Unvented Heater
Total
55,000 BTU/Hr
+33,000 BTU/Hr
88,000 BTU/Hr
This heater shall not be installed in a confined
space or unusually tight construction unless
provisions are made for adequate combustion
and ventilation air.
4. Compare the maximum BTU/Hr rating the space can
support with the total BTU/Hr used by the appliances.
Example:
W A R N I N G
If the area in which the heater may be operated
is smaller than that defined as an unconfined
spaceof if the building is of unusually tight
constructins, provide adequate combustion and
ventilation air by one of the methods described
in the National Fuel Gas Code, ANSI Z223.1/
NFPA 54, Section 5.3 or applicable codes.
76,800 BTU/Hr - max. the space can support
88,000 BTU/Hr - total used by appliances
In this example, the maximum BTU/Hr that the space
can support is less than the total used by the appli-
ances, the space is considered to be Confined space.
Additional air must be provided to meet the require-
ments of the Unvented heater.
12”
Option 1
Vents to Ad-
joining Room
Option 3 -
Vents to
Adjoining
Room
Option 2
- Remove
Door to
Adjoining
Rooms
12”
VO370-2
Fig. 3 Vent options to provide additional air.
8
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Assembly Procedures
4. Secure the snapstat wire harness to the shroud
panel using the wire tie provided.
Unpack the Stove
The UVS27 is shipped fully assembled on its back.
Unpack the stove and carefully set it upright.
5. Replace shroud and tighten the two (2) hex head
nuts on lower inside of shroud.
6. Route the rheostat control switch and wire forward
under the stove. Use the wire tie to secure the fan
and rheostat wire harnesses together to the tubing
under the bottom heat shield.
CAUTION
Porcelain enamelled surfaces are fragile. Handle
porcelain enamelled castings tenderly. Familiarize
yourself with the assembly steps before you begin
and proceed with deliberation and care. If possible,
have assistance available.
7. Install the rheostat onto the bracket to the left of the
valve. (Fig. 7)
Place enamelled castings on a soft, cushioned sur-
face until you are ready to assembly.
Avoid contact between the castings and other hard
surfaces or objects.
Install Optional Fan Kit
ST346a
1. Remove shroud assembly by loosening two (2) hex
head bolts on lower inside of shroud. Lift shroud as-
sembly up and away from stove.
Fig. 6 Attach snapstat to inner shroud.
2. Attach the fan to the rear shroud by engaging the
upper flange of the fan skirt under the lower edge of
the shroud and secure the skirt with the four screws
and one star washer provided. (Figs. 4, 5)
Retaining Nut
Control Knob
Rheostat
FK104
Fig. 7 Attach rheostat to bracket.
Upper
Flange
MOTOR
BLK
ST344a
Fig. 4 Place upper flange behind lower edge of shroud.
SNAPSTAT
WHT
BLK
ON/OFF
RHEOSTAT
ST236
Fig. 8 Fan wiring diagram.
WARNING
ST345a
Failure to position the parts in accordance with these
diagrams, or failure to use only parts specifically ap-
proved with this heater may result in property dam-
age or personal injury.
Fig. 5 Correct position of fan skirt installation.
3. Feed the snapstat wire lead up between the inner and
outer rear shroud panels and secure the snapstat to
the upper right side of the inner shroud. (Fig. 6)
9
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Install ON/OFF Switch
On/Off Switch Wiring
ON
OFF
The switch assembly parts are found in the parts bag.
1. Attach switch assembly to left rear side of stove
shroud using two screws and existing holes in
shroud. (Fig. 9)
2. Run wires down back of stove, under bottom of rear
shroud to valve.
3. Attach wires to valve terminals. (Fig. 10)
TP/TH
Switch As-
Existing
sembly
Holes
TP
TH
Black
ST124b
Optional Thermostat/Remote Wiring
Thermostat/Remote
(Optional)
Screws
ST315
Fig. 9 Attach switch assembly to rear shroud.
TP/TH
TP
TH
Black
ST124c
Fig. 11 ON/OFF switch and optional Thermostat/Remote
wiring.
ST228
Glass & Catalyst Installation
Fig. 10 Attach switch wires to valve.
CAUTION: Air shutter on Natural Gas units
must be adjusted when installing glass and
catalyst for proper operation. LP units do
not use an air shutter.
1. Remove screen. (Fig. 12) Remove rear, left and right
log bracket assembly by unfastening the two screws
which hold the burner in place.
Thermostat Connection (Optional)
Use only a thermostat rated for 500 - 750 millivolts.
Do not use low voltage (24V) thermostats.
Check the table below for the appropriate gauge ther-
mostat wire to use for the length of lead required in your
installation.
Thermostat Wire / Gauge
Maximum Run
40 feet
18
20
22
Screen Hooks
25 feet
16 feet
1. Install the wall thermostat in the desired location and
run the wires to the stove location. Terminate these
leads with 1/4” female connectors.
2. Connect the thermostat wires to the valve. (Fig. 11)
ST713
Fig. 12 Remove screen.
10
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
2. Hold the burner at the right hand side and lift to clear
the right burner leg. Then pull to the right to clear the
injectors on the left hand side.
6. Slide the catalyst through the grille opening. Set
catalyst on top of firebox. Secure with two (2) screws
and washers. (Fig. 15)
3. Turn burner upside down and remove air shutter.
Turn air shutter upside down and replace on burner.
(Fig. 13)
7. Shoulder bolts provided in catalyst kit must be in-
stalled on top of firebox. Use nut to secure in place.
(Fig. 15)
4. Replace burner. Slide the burner in at an angle
with left side lower than the right side. Slide the left
side onto the injectors, making sure the burner leg
remains at a 90° angle to the base. (Fig. 14) Lower
the right hand side down in to place. Make sure
the burner is as far left as possible and the injector
shoulders are inside the burner.
8. Install glass frame assembly by resting the bottom
edge of the frame on support brackets below the
front opening of the firebox. Rotate the top edge of
the assembly toward the firebox, and center it. Fas-
ten by “rotating” the cams over the top left and right
edges of the frame. (Fig. 16)
Air Shutter as Shipped from Factory
Shoulder
Bolts
Catalytic Combustor
Bottom of Burner Pan
Air Shutter Turned Upside Down
NOTE: Shown with top
removed for clarification.
ST709
Fig. 15 Install shoulder bolts and set catalytic combustor in
place.
ST667
Fig. 13 Remove air shutter, turn upside down and replace.
NOTE: Shown with top
removed for clarification.
ST711
Left Burner Leg
Injector Orifices
90°
Fig. 16 Rotate cams into place to hold glass frame assembly
in place.
ST353a
Fig. 14 Be sure injector orifices remain at 90° to the base.
5. Replace rear, left and right log bracket assembly and
replace logs.
11
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Connect the Gas Supply Line
CAUTION
This appliance should only be connected
by a qualified gas technician. Test to
confirm manifold pressures as specified
below.
Check the Rating Plate attached by a steel cable to the
firebox, to confirm that you have the appropriate firebox
for the type of fuel to be used.
The appliance should have a main gas valve provided
in an accessible location for turning on or shutting off
the gas to the main burner.
The UVS27 and its individual shutoff valve must
be disconnected from the gas supply piping dur-
ing any pressure testing of that system at test
pressures in excess of 1/2 psig (3.5 kPa).
This appliance should only be connected by a
qualified gas technician. Test to confirm manifold
pressures as specified below.
The UVS27 must be isolated from the gas supply
piping system by closing its individual manual
shutoff valve during any pressure testing of the
gas supply piping system at test pressure equal
to or less than 1/2 psig.
The UVS27 and its individual shutoff valve must be
disconnected from the gas supply piping during
any pressure testing of that system at test pres-
sures in excess of 1/2 psig (3.5 kPa).
There must be a gas shutoff between the stove
and the supply.
The UVS27 must be isolated from the gas supply
piping system by closing its individual manual
shutoff valve during any pressure testing of the gas
supply piping system at test pressure equal to or
less than 1/2 psig.
In order to connect Natural Gas, use a fitting
with 1/2” NPT on the valve side and 1/2” natural
gas supply line with an input of 28,000 BTUs at a
manifold pressure of 3.5” between minimum inlet
supply of 5.5” w.c. and maximum of 14.0” w.c.
There must be a gas shutoff between the stove and
the supply.
In order to connect Propane, use a fitting with 1/2”
NPT on the valve side and 1/2” propane gas sup-
ply line with an input of 28,000 BTUs at a manifold
pressure of 11.0” between a minimum inlet sup-
ply of 11.0” w.c. and maximum of 14.0” w.c.
In order to connect Natural Gas, use a fitting with
3/8” NPT nipple on the valve side and 1/2” natural
gas supply line with an input of 28,000 BTUs at a
manifold pressure of 3.5” and minimum inlet supply
for adjustment of 5.5” w.c.
In order to connect Propane, use a fitting with 3/8”
NPT nipple on the valve side and 1/2” propane gas
supply line with an input of 28,000 BTUs at a mani-
fold pressure of 11.0” and minimum inlet supply for
adjustment of 11.0” w.c.
Install Log Set
WARNING
Failure to position the parts in accordance with
this diagram or, failure to use only parts specifi-
cally approved with this heater, may result in
property damage or personal injury. Do not alter
the logs!
Gas connection should be made in accordance with
current National Fuel Gas Code, ANSI Z223.1/NFPA
54. Since some municipalities have additional local
codes, be sure to consult you local authority.
Connect the gas supply and test for leaks. Use a 50/50
solution of liquid soap and water to test for leaks at gas
fittings and joints. NEVER test with an open flame.
Light the pilot according to the directions on Psage 17,
before going to the next step.
Loose material shall be installed per the instruc-
tions. Replacement of loose material must be
purchased from the original room heater manu-
facturer and application of excess loose material
may adversely affect performance of heater.
Warning: All previously applied loose material
must be removed prior to reapplication.
1. Remove the logs from their packaging, and inspect
each piece for damage. DO NOT INSTALL DAM-
AGED LOGS.
2. Install the rear log by placing it on the sheet metal
shelf at the back of the firebox. (Fig. 17) The log
should touch the back wall of the firebox and be
centered.
12
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Complete the Installation
3. Install the right log by placing it on the sheet metal
bracket behind the grate with the right end of the log,
“the thicker end”, touching the grate and the right
side the firebox. Swing the left end of the log “paint-
ed end”, backward until it comes in contact with the
branch on the rear log. Set the log down over the
bent tab on the right. When the log is in place it rests
on the tab mentioned earlier and the tip of it comes
in contact with the branch on the rear log. (Fig. 17)
1. Install the screen frame by sliding the hooks over the
top front edge of the firebox and resting the bottom
on the support brackets. If the catalyst has been in-
stalled, place the glass front on the stove by resting
the bottom edge of the frame on support brackets
below the front opening of the firebox. Rotate the top
edge of the assembly toward the firebox, and center
it. Rotate the right and left cams towards the back of
the firebox to secure glass frame in place.
Left Log
Right Log
2. Grasp the front plate by the window bars and lift
into position engaging the two steel tabs behind the
adjacent bosses in the side plates. (Fig. 19) Seat the
front against the sides so the tabs at the bottom lip
engage with the notches in the stove legs.
Engage steel tabs
behind the cast
iron bosses
LG223
Rear Log
Fig. 17 Install rear, left and right logs.
Control Door
4. Install the left log by placing it on the sheet metal
bracket behind the grate with the left end of the log,
“the thicker end” touching the grate and the left end
of the firebox. Lay the log into the recessed area
on the left branch of the rear log. When the log is
in place, it will rest on the left branch of the rear log
toward the left side of the branch.
Bottom Tabs engage
notch in the leg.
ST112b
Fig. 19 Install the Front Plate. Your Front may look different
from that shown.
On the Pinnacle, the front tabs will engage behind the
notched cutouts in the base of either side plate. (Fig.
20)
5. Loosely sprinkle the lava rocks directly on top of the
burner just behind decorative grate. (Fig. 18) Do not
place lava rocks toward back of burner. The lava
rock is shipped inside the bag assembly.
When properly installed, the bottom of the front plate
cannot be pulled away form the sides without lifting it.
NOTE: Be sure the control door can swing out. It
should close against the steel tab stop.
If installing the optional warming shelf, you may find it
easiest to attach it to the top plate before placing the
top in position on the stove. Follow the instructions sup-
plied with the kit.
LG224
Fig. 18 UVS27 logs in place.
13
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Grille
Screen
Bottom Tabs engage notch
in the base.
ST113a
Levelling
Screws
Fig. 20 Engage the Hearthmount Front with the notch in the
ST114b
bse of each side plate.
Fig. 21 Install the Top Plate and Grille.
3. Lay the screen and top grille in place.
This completes assembly of the Stardance Freestand-
ing and Pinnacle Hearthmount shells.
14
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Operation
Your First Fire
Turn
Read these instructions carefully and familiarize
yourself with the burner controls shown on Page 17.
Locate the pilot assembly, Figure 22. Follow the lighting
instructions on Page 16 exactly.
HI
counterclockwise
to decrease
Turn clockwise
to increase
flame height
LO
flame height
HV102
During the first fire, it is not unusual to smell some
odor associated with new logs, paint and metal being
heated. Odors should dissipate within the first eight to
ten hours, however, you can open a window to provide
Fig. 23 Flame adjustment knob for Honeywell Valve.
SIT 630
fresh air to alleviate the condition.
Turn
counterclockwise
to increase
Pilot and Burner Inspection
Turn clockwise
to decrease
flame height
HV117
Each time you light your heater check that the pilot
flame and burner flame patterns are as shown in Fig-
ures 25 and 26. If flame patterns are incorrect, turn the
heater off. Contact your dealer or a qualified gas techni-
cian for assistance. Do not operate the heater until the
pilot flame is correct.
flame height
Fig. 24 Flame adjustment knob for Eurosit Valve.
Flame Characteristics
Follow regular maintenance procedures as described
on Page 19.
It is important to periodically perform a visual check of
the pilot and burner flames. Compare them to the picto-
rial illustrated below. (Figs. 25, 26) If the flame patterns
appear abnormal contact a qualified service provider for
service and adjustment.
Natural
Pilot
ST198
Fig. 25 Correct pilot flame appearance.
LP Pilot
ST673
Fig. 22 Pilot assembly location.
Flame & Temperature Adjustment
RN/RP Models
For units equipped with ‘HI/LO’ valves the flame adjust-
ment is accomplished by rotating the ‘HI/LO’ adjustment
knob located near the center of the gas control valve.
(Figs. 23, 24)
LG225
Fig. 26 Correct burner flame pattern.
15
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Lighting and Operating Instructions
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING:If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This heater has a pilot which must be lit manu-
ally. When lighting the pilot follow these
•
If you cannot reach your gas supplier, call the
Fire Department
instructions exactly.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it, call a
qualified service technician. Applying force or any
attempted repair may result in a fire or explosion.
B. BEFORE LIGHTING smell all around the heater
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS
D. Do not use this fireplace if any part has been under
water. Immediately call a qualified service techni-
cian to inspect the heater and to replace any part of
the control system and any gas control which has
been under water.
•
•
•
•
Do not try to light any fireplace
Do not touch any electric switch
Do not use any phone in your building
Immediately call your gas supplier from a neigh-
bor’s phone. Follow the gas supplier’s instruc-
tions.
Lighting Instructions
1. STOP! Read the safety information above.
2. Turn off all electrical power to the fireplace.
3. For MN/MP/TN/TP appliances ONLY, go on to
Step 4. For RN/RP appliances turn the On/Off
switch to “OFF” position or set thermostat to low-
est level.
10. Push the control knob all the way in and hold.
Immediately light the pilot by repeatedly depress-
ing the piezo spark ignitor until a flame appears.
Continue to hold the control knob in for about one
(1) minute after the pilot is lit. Release knob and it
will pop back up. Pilot should remain lit. If it goes
out, repeat steps 5 through 8.
4. Open control access panel.
5. Push in gas control knob slightly and turn clock-
wise
to “OFF”.
3/8" - 1/2"
OFF
PILOT
o
2
O
Honeywell
Euro SIT
SIT NOVA
•
If knob does not pop up when released, stop
and immediately call your service technician or
gas supplier.
6. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you
smell gas, STOP! Follow “B” in the safety infor-
mation above. If you do not smell gas, go to the
next step.
7. Remove glass door before lighting pilot. (See
Glass Frame Removal section).
8. Visibly locate pilot by the main burner.
9. Turn knob on gas control counterclockwise
to “PILOT”.
•
If after several tries, the pilot will not stay lit,
turn the gas control knob to “OFF” and call your
service technician or gas supplier.
11. Replace glass door.
12. Turn gas control knob to “ON” position.
13. For RN/RP appliances turn the On/Off switch to
“ON” position or set thermostat to desired setting.
14. Turn on all electrical power to the fireplace.
To Turn Off Gas To Heater
1. Turn the On/Off switch to Off position or set the
thermostat to lowest setting. (R Models only)
2. Turn off all electric power to the fireplace if serv-
ice is to be performed.
3. Open control access panel.
4. Push in gas control knob slightly and turn clock-
wise
to “OFF”. Do not force.
5. Close control access panel.
16
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Troubleshooting
Follow these procedures in the order presented.
W A R N I N G
TURN OFF HEATER AND ALLOW TO COOL
COMPLETELY BEFORE SERVICING.
CONDITION
POSSIBLE CAUSE
SOLUTION
1. Inspect and re-connect, replace
or repair as necessary.
No spark at pilot when Ignitor is
operated.
1. Ignition Electrode is disconnected
from ignition wire, broken or incor-
rectly positioned.
2. Replace wire.
3. Replace Piezo Ignitor.
2. Ignitor wire is broken.
3. Bad Piezo Ignitor.
1. Gas supply is turned off or supply
line shut-off valve is closed.
2. Control Knob is not in PILOT posi-
tion.
1. Turn on gas supply or open sup-
ply line shut-off valve.
2. Turn Control Knob to PILOT.
The Ignitor Electrode sparks,
but Pilot does not light.
3. Control Knob not pressed in while
in PILOT position.
3. Press Control Knob in while in
the PILOT position.
4. Air present in gas lines.
4. Continue holding in Control Knob
and repeat ignition procedure
until air is bled from the lines.
5. Call local gas supplier. Adjust
inlet supply pressure to specifica-
tion: NG; 5.5” w.c.-14.0”w.c. LP;
11.0” w.c.-14.0”w.c.
5. Inlet supply pressure is not within
correct settings.
6. Other conditions that should be
identified only by a qualified gas
technician.
6. Call qualified gas technician.
Piezo Ignitor
OFF
PILOT
L
I
O
H
Regulator
HV104
Pilot / Main Control
Fig. 27 Honeywell valve assembly.
17
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Troubleshooting cont’d.
SOLUTION
CONDITION
POSSIBLE CAUSE
Pilot lights but flame goes out
when Control Knob is released.
1. Control Knob not fully depressed
or held in long enough.
1. Depress Control Knob fully and
hold in for a full 30 seconds.
2. Gas supply line shut-off valve is
not fully open.
3. Thermocouple connection is
loose at the Control Valve.
2. Fully open gas supply line shut-
off valve.
3. Inspect and tighten securely.
4. Pilot flame does not touch the
Thermocouple.
4. A) Call local gas supplier. Adjust
inlet supply pressure to specifica-
tion: NG; 5.5” w.c.-14.0”w.c. LP;
11.0” w.c.-14.0”w.c.
This can be caused by:
Pilot flame is lifting.
Thermopile
A) Incorrect gas pressure, and/or
B) other conditions that should
be identified only by a qualified
service technician.
B)Call local gas service techni-
cian.
Thermo-
couple
5. Thermocouple is damaged.
6. Control Valve is damaged.
5. Call local gas service technician.
6. Call local gas service technician.
ST121a
Pilot flame is weak - does not touch
Thermocouple.
Correct LP Pilot Flame.
Correct NG Pilot Flame.
1. Gas supply line shut-off valve is
not fully open.
Pilot lights but Main Burner does
not.
1. Fully open gas supply line shut-
off valve.
2. Foreign material is blocking
Burner ports.
2. Insptect and clear debris away
from Burner ports.
3. Main Burner orifice is clogged.
4. Thermostat or remote switch not
activated on JUVS.
3. Call local gas service technician.
4. Set thermostat to higher tem-
perature or check remote switch.
5. Call local gas service technician.
5. Bad Thermopile.
1. Insufficient fresh air.
1. Determine that adequate ventila-
tion exists to provide sufficient
fresh air. Open a window or pro-
vide additional ventilation. (See
Fresh Air Requirements, Pages
6-7)
Main Burner shuts off and Pilot
flame goes out while in operation.
2. Incorrect inlet supply pressure.
2. Call local gas supplier. Adjust
inlet supply pressure to specifica-
tion: NG; 5.5” w.c.-14.0”w.c. LP;
11.0” w.c.-14.0”w.c.
18
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Maintenance
The following procedures will help ensure that your
heater continues to perform safely and efficiently.
Screen Hooks
Firebox Cleaning and Inspection
Cleanliness is critical to correct operation of the
heater. The log set, burner, valve controls and air
circulation areas must all be kept free of dust and
unobstructed by debris. Inspect these areas before
each use and clean whenever accumulation is evi-
dent. Follow the simple procedure outlined below.
Glass Latch
Frequent cleaning may be necessary in living environ-
ments subject to excessive carpet lint or pet hair. For
example, if you live with a dog that sheds continuously,
you will need to inspect the burner area frequently and
clean it as often as the accumulation requires. In ex-
treme conditions, it may be necessary to clean the
burner and log set monthly or bi-weekly.
ST712
Fig. 28 Remove the screen or glass panel.
Glass Replacement
If so equipped, do not operate this appliance with the
glass panel cracked, broken, or removed. Replace
damaged glass only with an approved CFM Corporation
ceramic glass panel. Follow the Cleaning Procedure
instructions regarding parts removal.
This appliance should be inspected and thoroughly
cleaned annually by a qualified gas technician.
Cleaning Procedure
1. Turn the burner OFF and let the heater cool com-
Care of Cast Iron
pletely before cleaning.
An occasional dusting with a dry rag will help keep the
painted surfaces looking new. Use high-temperature
stove paints, available through your local dealer, to
touch-up areas as needed. Clean areas to be painted
with a wire brush and be sure to cover the log set,
burner and valve assembly. Apply the paint sparingly;
two light coats of paint will give better results than a
single heavy coat.
2. Lift the Front plate up and then swing the bottom out
to disengage it from the heater shell. (Page 13, Fig.
19)
3. Remove the screen by lifting up and away from the
unit. Or, if so equipped, remove the glass panel by
rotating the two cams toward the front of the firebox.
Lift the panel up and off of the firebox frame. (Fig.
28)
Porcelain enamel surfaces should be cleaned
with a soft, damp cloth. Do not use abrasive cleaning
agents. If necessary, use only a cleaning agent formu-
lated specifically for use on porcelain enamel surfaces.
4. Carefully inspect the log set for damage. Contact
your local dealer if any damage is evident. DO NOT
OPERATE THE HEATER WITH A DAMAGED OR
LOOSE LOG SET.
Use a soft-bristled brush vacuum cleaner attachment
to remove dust or debris from the log set, pilot and
burner. Use care as the log set is fragile.
WARNING
Turn the burner Pilot OFF before applying paint.
NEVER paint pilot or around pilot area.
5. Inspect the catalytic combustor at the top of the
firebox. Replace the combustor if any damage or
deterioration is evident.
WARNING
6. Replace the screen or glass panel and the front
plate. DO NOT OPERATE THE HEATER WITH
THE SCREEN / GLASS PANEL OR FRONT PLATE
REMOVED.
Dust and debris accumulation can result in poor
performance. Inspect the Valve compartment,
burner parts and log set frequently and Clean
these parts monthly or as often as accumula-
tion warrants.
19
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Catalytic Combustor
The combustor should be cleaned annually to ensure
optimal performance. Follow the procedure below.
Remove the Combustor Module
1. Be sure the heater is COLD.
2. Remove the screws and washers holding the com-
bustor in place. Lift combustor up and out.
Clean the Combustor Module
1. Clean the outer surface of the filter with the brush
attachment of your vacuum cleaner to remove loose
dirt.
2. Submerge the filter in a mild soapy water solution.
Rinse thoroughly with distilled water.
3. Replace in heater when dry.
Replace the Combustor Module
1. Replace combustor on top of firebox.
2. Secure with screws and washers removed earlier.
Refer to Page 11, Figure 15.
20
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
8
7
1a
2a,b
5
6
1b
1d
4
3
1c
10a
10b
12
13
O F F
11
10c
10d
9a,b
17
9c,d
25
14a,b
16a,b,c,d
22
15
23
24
18
21
30
32
31
26
29
19
27
5004
CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time,
without notice.
UVS27R, UVS27M Vent Free Gas Heaters
Models 4030-4049, 4085 - 4087, 4090 - 4092
21
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
UVS27R, UVS27M Vent Free Gas Heaters
Models 4030-4049, 4085 - 4087, 4090 - 4092 (continued)
Ref. Description
UVS27
1. Gas Log Assembly - UVS27
1a. Log #V40 Rear UVS27
20005005
20005006
1b. Log #V42 Left UVS27
20005008
1c. Log #V41 Right UVS27
20005007
1d. Lava Rocks Burner
57897
2a. Manifold Assy. - UVS27R
20003739
2b. Manifold Assy. - UVS27M
20004935
3. Damper Steel Handle/Screw (Stardance Operable Door Only)
4. Handle Package, Ceramic w/Screw (Stardance Operable Door Only)
5. Trim ON/OFF Switch
30002720
0004345
53606
6. Screen UVS27
20005009
7. Glass Frame Assembly - SDV30
8. Glass w/Gasket (Comes with UVGODCFK)
9a. Valve NG Honeywell - VS84212003
9b. Valve LP Honeywell - VS84212011
9c. Valve MN Eurosit 0.630.564
9d. Valve MP Eurosit 0.630.563
10a. Oxygenerator, NG OP #8204
10b. Oxygenerator, LP OP #8404
10c. Oxygenerator, NG OP #8202
10d. Pilot ODS TP OP #8402
30000127
20005018
10000235
10000242
20001354
20001355
55464
55465
20004435
20001357
11. Front, Stardance OP DR (Stardance Only)
12. Door, Left - Stardance
Refer to Enamel Parts Chart Page 23
Refer to Enamel Parts Chart Page 23
13. Door, Right - Stardance
Refer to Enamel Parts Chart Page 23
14a. Burner Housing Assy. - JUV NG
14b. Burner Housing Assy. - LP
15. Bracket, Rear Log - JUV
20003130
20004995
20003274
16a. Orifice Hood #69 (.0292”) - Front - LP
16b. Orifice Hood #54 (.055”) - Front - NG
16c. Orifice Hood #54 (.055”) - Rear - LP
16d. Orifice Hood #44 (.086”) - Rear - NG
17. Ignitor Piezo - Honeywell #396079
18. Gasket, Base Pan Inner
30000513
20000130
20000130
30000334
20000062
20002566
19. Bracket Support Right Log
20. Bracket Support Left Log
20004920
20005022
21. Grate Decorative Burner
20003022
22. Grille, UV30
30000393
23. Mesh, Grille - UV30
30000508
24. Top, Stardance UV/PDV
25. Front, HM-VC
26. Door, Control - FS/HM
27. Cover, Valve w/Piezo
Refer to Enamel Parts Chart Page 23
Refer to Enamel Parts Chart Page 23
Refer to Enamel Parts Chart Page 23
51851
28. Catalyst, RUV (not shown) (Comes with UVGODCFK)
29. Left End - Hearthmount
30. Right End - Hearthmount
31. Left End - Freestanding
32. Right End - Freestanding
30000506
Refer to Enamel Parts Chart Page 23
Refer to Enamel Parts Chart Page 23
Refer to Enamel Parts Chart Page 23
Refer to Enamel Parts Chart Page 23
1203560
33. 1/4” Fiberglass Gasket
22
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
UVS27R, UVS27M Vent Free Gas Heaters
Models 4030-4049, 4085 - 4087, 4090 - 4092 (continued)
Shell Enamel Part Numbers - Hearthmount Models: 4085 - 4087, 4090 - 4092
Color
Classic
Sand
Top
Left End
30001282
30001303
30001310
Right End
30001281
30001302
30001309
Front
Control Door
1301087
1301083
1321083
1341083
1301129
1321129
1341129
1321087
1341087
Midnight
Shell Enamel Part Numbers - Freestanding Models
Color
Classic
Biscuit
Bordeaux
Chestnut Brown 30003315
Top
Left End
30001280
30003300
30001287
30003308
30001308
30001294
30001321
30001301
30002547
Right End
30001279
30003301
30001286
30003309
30001307
30001293
30001320
30001300
30002548
Front (OP)
30001496
30003302
30001261
30003310
30001270
30001264
30001314
30001267
30002550
Left Door
30001139
30003304
30001263
30003312
30001272
300012266
30001316
30001269
30002552
Right Door
30001138
30003303
3001262
30003311
30001271
30001265
30001315
30001268
30002551
30001278
30003307
30001285
Ebony
30001306
30001292
30001319
30001299
30002554
Forest Green
Midnight Blue
Sand
Suede Brown
Vermont
Classic Green
30003323
30003316
30003317
30003318
30003320
30003319
23
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
Optional Accessories Available
Fan Kits
Remote Controls
FK28 Fan Assembly
The remote control allows you to turn the heater on or
off from anywhere in the room. Remote controls are
available for the UVS27R only. Refer to Figure 17,
Page 12 for wiring diagram.
The FK28 fan kit helps distribute heated air from within
the firebox out into the room. The fan is controlled by a
snapstat that turns power on and off as the firebox tem-
perature rises above and falls below a preset tempera-
ture. A rheostat provides for variable fan speeds.
Model
Function/s Controlled
RC1
RC2
IMTFK
ON/OFF
ON/OFF and Temperature
Wall mounted thermostat control
Specifications
115 Volt / 60Hz / .75 Amps
Maintenance
Warming Shelf
The fan itself does not require regular maintenance,
however periodic cleaning of the fan and the surround-
ing area is required.
Warming shelves add versatility to your stove. The
warming shelf can be used to keep foods warm at
mealtime.
Installation
Model
Pinnacle Stardance
Refer to Assembly Section, Page 9 for installation
instructions.
Shell
Shell
Color
2702
2684
n/a
n/a
n/a
n/a
n/a
2764
2765
2702
2684
2685
2688
2704
2706
2711
2764
2765
Classic Black
Biscuit
Chestnut Brown
Vt. Classic Green
Bordeaux
Forest Green
Midnight Blue
Sand
Glass / Catalyst Kit UVGODCFK
The glass panel replaces the standard screen. The
catalytic combustor installs easily into the upper mani-
fold above the firebox.
Ebony
The shelf installation is done in three stages. First you
attach the shelf loosely to the stove, leaving the screws
loose enough to allow final adjustments. Then, you po-
sition the shelf and adjust the brackets so the shelf fits
correctly. Finally, you tighten the screws.
Refer to the instructions included with each warming
shelf for complete installation procedures.
24
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
25
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
UVS27 Vent-Free Gas Heater
26
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED LIFETIME WARRANTY
PRODUCT COVERED BY THIS WARRANTY
All Vermont Castings gas stoves, gas inserts, and gas fireplaces, and all Majestic or brand gas
fireplaces equipped with an Insta-Flame Ceramic Burner, or standard steel tube burner.
BASIC WARRANTY
•
•
Any part and/or component replaced under the provisions of this
warranty is covered for six months or the remainder of the original
warranty, whichever is longest.
CFM Corporation (hereinafter referred to collectively as the Company)
warrants that your new Vermont Castings or Majestic Gas Fireplace/
Stove is free from manufacturing and material defects for a period of
one year from the date of purchase, subject to the following conditions
and limitations.
This warranty is limited to the repair of or replacement of part(s) found
to be defective in material or workmanship, provided that such part(s)
have been subjected to normal conditions of use and service, after
said defect is confirmed by the Company’s inspection.
EXTENDED LIFETIME WARRANTY
The heat exchanger, where applicable, and combustion chamber
of every Vermont Castings or Majestic gas product is warranted for
life against through wall perforation. All appliances equipped with an
Insta-Flame Ceramic Burner have limited lifetime coverage on the
ceramic burner plaque. Warrantees are made to the original owner
subject to proof of purchase and the conditions and limitations listed
on this Warranty Document
•
•
The company may, at its discretion, fully discharge all obligations
with respect to this warranty by refunding the wholesale price of the
defective part(s)
Any installation, labor, construction, transportation, or other related
costs/expenses arising from defective part(s), repair, replacement,
or otherwise of same, will not be covered by this warranty, nor shall
the Company assume responsibility for same. Further, the Company
will not be responsible for any incidental, indirect, or consequential
damages except as provided by law.
COMPONENT WARRANTY
CAST IRON: All external and internal cast iron parts are warranted for a
period of three years.
•
SOME STATES DO NOT ALLOW FOR THE EXCLUSION OR
LIMITATIONS OF INCIDENTALAND CONSEQUENTIAL DAMAGES
OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOUR
CIRCUMSTANCES. THIS WARRANTY GIVES YOU SPECIFIC
RIGHTSANDYOUMAYHAVEOTHERRIGHTSWHICHVARYFROM
STATE TO STATE.
Note: On porcelain enamel finished external parts and accessories
The Company offers no Warranty on chipping of enamel surfaces.
Inspect all product prior to accepting it for any damage to the
enamel.
The salt air environment of coastal areas or a high humidity
environment can be corrosive to the porcelain enamel finish. These
conditions can cause rusting of the cast iron beneath the porcelain
enamel finish, which will cause the finish to flake off.
•
•
•
•
All other warranties-expressed or implied- with respect to the product,
its components and accessories, or any obligations/liabilities on the
part of the Company are hereby expressly excluded.
Dye lot variations with replacement parts and/or accessories can
occur and are not covered by warranty.
The Company neither assumes, nor authorizes any third party to
assume on its behalf, any other liabilities with respect to the sale of
this Vermont Castings or Majestic product
GLASS DOORS: Glass doors are covered for a period of one year.
Glass doors are not warranted for breakage due to misuse or accident.
Glass doors are not covered for discoloration or burned in stains due to
environmental issues, or improper cleaning and maintenance.
The warranties as outlined within this document do not apply to
chimney components or other non CFM Corporation accessories used
in conjunction with the installation of this product..
BRASS PLATED PARTS AND ACCESSORIES: Brass parts should be
cleaned with Lemon oil only. Brass cleaners cannot be used. Mortar
mix and masonry cleaners may corrode the brass finish. The Company
will not be responsible for, nor will it warrant any brass parts which are
damaged by external chemicals or down draft conditions.
Damage to the unit while in transit is not covered by this warranty but
is subject to claim against the common carrier. Contact the dealer
from whom you purchased your fireplace/stove (do not operate the
appliance as this might negate the ability to process the claim with the
carrier).
GAS VALVES: Gas valves are covered for a period of one year
•
•
The Company will not be responsible for:
ELECTRONIC AND MECHANICAL COMPONENTS: Electronic and
mechanical components of the burner assembly are covered for one
year. All steel tube burners are warranted for one year.
a) Down drafts or spillage caused by environmental conditions such
as near-by trees, buildings, roof tops, hills, or mountains.
b) Inadequate ventilation or negative air pressure caused by
mechanical systems such as furnaces, fans, clothes dryers, etc.
ACCESSORIES: Unless otherwise noted all components and CFM
Corporation company supplied accessories are covered for a period of
one year.
This warranty is void if:
a) The fireplace has been operated in atmospheres contaminated by
chlorine, fluorine, or other damaging chemicals.
CONDITIONS AND LIMITATIONS
b) Thefireplacehasbeensubjectedtoprolongedperiodsofdampness
or condensation
c) Anydamagestothefireplace,combustionchamber,heatexchanger
orothercomponentsduetowater, orweatherdamage, whichisthe
result of but not limited to, improper chimney/venting installation.
d) Any alteration, willful abuse, accident, or misuse of the product
•
ThisVermontCastingsorMajesticproductmustbeinstalledorserviced
by a qualified installer, preferably NFI or WETT (Canada) certified, as
prescribed by the local jurisdiction. It must be installed and operated at
all times in accordance with the Installation and Operating instructions
furnished with the product. Any alteration, willful abuse, accident, or
misuse of the product shall nullify this warranty.
has occurred.
•
•
This warranty is non-transferable, and is made to the original owner,
provided that the purchase was made through an authorized supplier
of the Company.
IF WARRANTY SERVICE IS NEEDED…
1) Contact your supplier. Make sure you have your warranty,
your sales receipt, and the model/serial number of your
CFM Corporation product.
2) DO NOT ATTEMPT TO DO ANY SERVICE WORK
YOURSELF.
The customer must pay for anyAuthorized Dealer in-home travel fees
or service charges for in-home repair work. It is the dealers option
whether the repair work will be done in the customer’s home or in the
dealer’s shop.
•
Ifuponinspection,thedamageisfoundtobethefaultofthemanufacturer,
repairs will be authorized at no charge to the customer parts and/or
labor.
27
20007068
Download from Www.Somanuals.com. All Manuals Search And Download.
CFM Corporation
410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6
Download from Www.Somanuals.com. All Manuals Search And Download.
|