e i n t e s d ’ e x t r ê m e s g r a v e s a u d i o / v i d é o
VRP-1000TM
and
VRP-1200TM
User's Manual
d e l ' U t i l i s a t e u r
HomeTheaterSubwoofer
Download from Www.Somanuals.com. All Manuals Search And Download.
Congratulations!
Congratulations on your purchase of a Velodyne Rear Port (VRP)
subwoofer system. This system represents the state-of-the-art in
home audio reproduction and will provide you with years of listening
pleasure when properly cared for. Read and follow this instruction
manual to insure safe and proper system connection and operation.
Caution!
Please observe the following instructions to insure safe and proper sys-
tem operation.
Note: Do not leave unit in direct sunlight or use in high humidity
environments!!!
Warning!
To prevent fire or shock hazard, do not expose this equipment to
rain or moisture. To avoid electrical shock, do not open speaker
enclosure or amp chassis cover. Please observe all warnings on
the equipment itself. There are no user serviceable parts inside.
Please refer all service questions to your authorizedVelodyne dealer.
Prior to Installation:
Please unpack the system carefully. This unit is heavy. Use caution
when lifting or moving to avoid injury. Remove all staples used to
seal the carton as they can scratch the cabinet. Please save the
carton and all packaging materials for future use. Packing this unit
in any other carton may result in severe damage when shipping.
Record the serial number in the space provided on page 13 for future
reference.
Product Features
• A single driver consisting of either:
- 10"(8.2"pistondiameter)subwooferwith2.0"high-tempvoice
coil and 40 ounce motor structure or,
- 12"(9.8"pistondiameter)subwooferwith2.0"high-tempvoice
coil and 40 ounce motor structure
• Adjustable (50 to 200 Hz) low-pass crossover with a 12 dB/octave
slope
• Line-level (RCA) inputs
• Speaker-level inputs and outputs with spring loaded terminals
a t i o n s
continued. . .
☞
2
Download from Www.Somanuals.com. All Manuals Search And Download.
• Signal sensing auto turn on/off
• Variable volume control
• Selectable phase control (0°or 180°)
• Frequency response of 36 - 120 Hz (+/-3 dB)
• Green power on/ Red power standby mode indicator LED
Prepare for Installation
Your newVelodyne subwoofer provides for a number of installation
options. Read all the installation information below in order to deter-
mine which installation option is best for your system. Remember
to perform all installation procedures with system power turned
off to prevent possible damage.
Placement
True subwoofers operate at extremely low frequencies that are pri-
marily omni-directional. Keep in mind that frequency response and
output level can be drastically influenced by placement, depending
on the acoustic properties of the listening room. Typically, the opti-
mum location for a subwoofer is tucked away in a corner of your
listening room. This location will usually offer the greatest output
levels and optimum low frequency extension. The worst location for
a subwoofer is typically far away from any walls, and close to the
center of your room. Avoid these locations when possible. When
using a pair of Velodyne subwoofers in stereo, it is preferable to
place each subwoofer by the satellite of the same channel.
Caution! This subwoofer has electronics built into the cabinet.
Do not place the cabinet next to sources of heat such as fur-
nace registers, radiators, etc., or near sources of excessive
moisture, such as evaporative coolers, humidifiers, etc. The
power cord should be routed in such a way that it will not be
walked on, pinched, or compressed in any way that could re-
sult in damaging the insulation or wire.
Regardless of where you install your Velodyne subwoofer, it must
remain in an upright position (woofer facing forward). Using, shipping,
or otherwise storing the subwoofer in any other position for an
extended period of time may result in damage to the unit not covered
by warranty.
YourVRP subwoofer is magnetically shielded to reduce the amount
of stray magnetic energy emitted from the speaker’s motor structure.
This greatly increases flexibility when placing the unit close to video
☞
3
Download from Www.Somanuals.com. All Manuals Search And Download.
monitors, as there is very little stray magnetism. Certain types of
televisions are particularly sensitive to stray magnetic fields. If
your television produces distorted colors after installing your
subwoofer, simply increase the distance between your television
and the subwoofer until normal color and operation is returned.
Your newVelodyne subwoofer, like any good speaker system, requires
proper positioning within the listening space to provide maximum
performance. Improperly placed speakers may degrade the sound
quality and reduce your listening pleasure. Depending on the size
and type of furnishings in the room, perfect placement may not be
possible. Finding the best location for your environment will likely
require some experimentation. We suggest you experiment with the
location during setup to find what sounds best to you when seated
in your typical listening position.
Installation
Inputs
Your new subwoofer is equipped with speaker-level and line-level
inputs. Use the LINE LEVEL jacks when connecting your subwoofer
to a pre-amp, signal processor (such as LFE out), line-level crossover,
or receiver with pre-amp level outputs. The SPEAKER LEVEL jacks
connect directly to the speaker outputs of any amplifier, integrated
amplifier, or receiver. Your amplifier section will notice no additional
loading effects when you use these inputs due to their very high
impedance.
Note: You do not need to connect both the left and right LINE LEVEL
inputs from a single source (such as the LFE out on your receiver/
processor). These inputs are summed together and simply
connecting one will provide the same amount of signal to the sub as
if you had used a “Y” connector and connected both. If using the
SPEAKER LEVEL inputs, you DO want to connect both channels,
since different bass information might be present in each channel
going to your main speakers.
Important!!!
Do not use both LINE LEVEL and SPEAKER LEVEL connections
simultaneously!
continued. . .
☞
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution!!! To avoid damage to your main amplifier, be sure to maintain
correct polarity when making all connections - red (positive) to red,
and black (negative) to black. Be sure all connections are tight, and
that there are no loose strands or frayed wires.
Volume Control
This control allows you to balance the output from the subwoofer to
the main speakers/amplifier in your system. This control should be
set to achieve similar output levels from both the main speakers
and subwoofer when listening to music. A good starting point for
the volume control is 2 or 3 graduations from minimum.
Low-pass Crossover - 50 to 200 Hz
As noted above, all inputs sum the left and right channels together,
with the resulting signal passing through an adjustable low-pass
crossover before being amplified. The crossover control allows you
to adjust the upper limit of the subwoofer’s frequency response from
50 to 200 Hz. The subwoofer’s response will begin rolling off above
the frequency you set this control to.You should set the crossover
frequency to obtain a smooth and seamless transition from the
subwoofer to the main speakers in your system. If your main
speakers are smaller units with limited low frequency output, you
may wish to choose a higher frequency (such as 100-120 Hz) than
you would with larger speakers which have greater low frequency
output. With larger speakers, you might start with this control set
lower, such as 80 Hz.
Phase Adjustment - 0°/180°
This control allows you to “reverse” the phase of the subwoofer’s
output signal 180°to correct for any possible mismatch and resulting
cancellation between the subwoofer and your main speakers/amplifier.
To adjust, simply listen to the system with music playing, then
depress the phase switch from one position to the other and listen
for a change in low frequency output. The correct position will have
a greater amount of apparent low frequency output.
Auto Turn on Function
The subwoofer will turn itself on automatically when an audio signal
is present. If no signal is present for approximately 8 minutes, the
unit will switch to standby mode (Red LED). While in standby mode,
your subwoofer will draw very minimal power.
☞
5
Download from Www.Somanuals.com. All Manuals Search And Download.
LOW-PASS
CROSSOVER
80 Hz
RED : STANDBY
GREEN : ON
4
5
SPEAKER LEVEL
R - - L
50Hz
+
+
200Hz
1
2
3
SUBWOOFER
VOLUME
INPUT
INPUT
R
L
PHASE
OUTPUT
00
1800
MIN
LFE IN
MAX
+
R
-
-
L
+
6
7
4 ~ 8 Ohm
R
L
D
I
S
T
E
C
US
LISTED
(AUDIO APPARATUS)
68BM E203436
VRP Series
WARNING:TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
100Watt
120V~
60Hz
2A
SERIAL #
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
AVIS:
DOUBLE INSULATION WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS
-
VELODYNE ACOUSTICS, INC.
MORGAN HILL, CA.
Figure 1.VRP Rear Panel Connections
Rear Panel Connections
Figure 1 shows the connections on the rear panel of the VRP.
Following are brief descriptions of the connections described in
Figure 1. More detail of these connections can be found below:
(1) SPEAKER LEVEL INPUT terminals
Connect these input terminals to the speaker output terminals
of your amplifier or receiver.
(2) SPEAKER LEVEL OUTPUT terminals
The speaker-level signal to the front speakers is output from
these terminals.
(3) LINE INPUT jacks
Connect these jacks to the LINE OUT jacks of the amplifier.
continued. . .
☞
6
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) LOW-PASS CROSSOVER
Use this knob to select the high-frequency range at which you
wish to cut-off the signal to the subwoofer.
(5) Power indicator
Red:
Unit is in standby mode.
Green:
Unit is in operation mode.
(automatically turns to STANDBY mode if no signal
for 8 min.)
(6) PHASE switch
Select the switch position at which you hear a louder bass sound.
(7) VOLUME LEVEL knob
Use this knob to adjust the output level of the subwoofer.
Crossovers
Speaker-levelConnections
When installed in this fashion the satellite speakers will be crossed
over at 80 Hz. This removes the lower bass from your amplifier and
speakers,enablingthemtodoabetterjobreproducinghighfrequencies.
By utilizing this method you will have a bi-amplified system, gaining
improved power and headroom for your system.
Receiver/ProcessorSubwooferOutputs
TheVelodyne subwoofer is designed to operate using the full range
audio signal for input when using the built-in crossover. Many home
theater processors/receivers (Dolby Digital®, DTS®, THX®) have a
“subwoofer out” jack (sometimes labeled “LFE”) that is internally
filtered, settable at the receiver/processor, and designed to be used
with a powered subwoofer. In some installations, it may be beneficial
to use BOTH the Velodyne crossover and the receiver/processor
crossover, resulting in a steeper ultimate crossover slope. In some
rare cases, combining both an external crossover and the one internal
to the subwoofer may result in low output and increased noise. In
these installations you may need to bypass the crossover in either
the processor or yourVRP subwoofer, or simply setting one crossover
to a higher frequency (such as 120 Hz) will restore maximum
performance.
(Refer to Figure 2a Line-Level Subwoofer Connection Diagram and
Figure 2b Speaker-Level Subwoofer Connection Diagram, page 8
and 9 for connection diagrams.)
☞
7
Download from Www.Somanuals.com. All Manuals Search And Download.
+ R - - L +
SUBWOOFER
OUTPUT JACK
REAR
AMPLIFIER
FRONT
LOW-PASS
CROSSOVER
80 Hz
RED : STANDBY
GREEN : ON
SPEAKER LEVEL
50Hz
+
R
-
-
L
+
200Hz
SUBWOOFER
VOLUME
INPUT
R
INPUT
PHASE
OUTPUT
00
L
1800
MIN
MAX
+
R
-
-
L
+
4 ~ 8 Ohm
LFE IN
R
L
D
I
C
S
E
US
T
LISTED
(AUDIO APPARATUS)
68BM E203436
VRP Series
WARNING:TO REDUCE THE RISK OF FIRE
100Watt
120V - 60Hz
2A
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
SERIAL # LABEL
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
AVIS:
DOUBLE INSULATION - WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS
VELODYNE ACOUSTICS, INC.
MORGAN HILL, CA.
SUBWOOFER REAR PANEL
Figure2a. Line-LevelSubwooferConnectionDiagram
continued. . .
☞
8
Download from Www.Somanuals.com. All Manuals Search And Download.
+ R - - L +
SUBWOOFER
OUTPUT JACK
REAR
AMPLIFIER
FRONT
LOW-PASS
CROSSOVER
80 Hz
RED : STANDBY
GREEN : ON
SPEAKER LEVEL
50Hz
+
R
-
-
L
+
200Hz
SUBWOOFER
VOLUME
INPUT
R
INPUT
PHASE
OUTPUT
00
L
1800
MIN
MAX
+
R
-
-
L
+
LFE IN
4 ~ 8 Ohm
R
L
D
I
S
T
E
C
US
LISTED
(AUDIO APPARATUS)
68BM E203436
VRP Series
100Watt
120V ~ 60Hz
2A
WARNING:TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
SERIAL #
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
AVIS:
DOUBLE INSULATION WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS
-
VELODYNE ACOUSTICS, INC.
MORGAN HILL, CA.
SUBWOOFER REAR PANEL
+
-
-
+
RIGHT FRONT SPEAKER
LEFT FRONT SPEAKER
Figure2b. Speaker-LevelSubwooferConnectionDiagram
☞
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Interconnect Cables
When installing your new Velodyne subwoofer using the line level
connections, you should always use shielded phono cables. There
aremanyhighqualitycablesavailabletoday. Itisrecommendedthat
you keep the length of cable as short as possible to avoid any
potentialnoiseproblems.
When using speaker level connections, use a high quality speaker
cable that mates well with the connectors. Be very careful to avoid
any loose strands or frayed wires that may result in a short, which
may damage your equipment. Cables of extremely large size are
typically not required. Extremely large gauge wire may not properly
fit in the binding posts, resulting in a poor connection and possible
short circuits.
Care of Your Subwoofer
YourVelodyne subwoofer does not require any regular maintenance.
Normal dusting or cleaning of the surface for appearance purposes
is all that is required. We suggest you avoid any harsh detergents or
chemicals when cleaning the cabinet. Abrasives, detergents, or
cleaning solutions may damage the finish on the cabinet. We
recommend using only a damp cloth to clean the cabinet.
During normal conditions, your new subwoofer may be left on
continuously without any problems. The unit is equipped with a
signal-sensing turn on/off that will automatically turn on the unit
when a signal is present at the inputs and turn off the unit after
several minutes when there is no longer any signal at the inputs.
Protection Circuitry
Your new subwoofer is equipped with circuitry to provide maximum
performance with greatest reliability.
The unit is protected against:
1) Overheating the amplifier.
2) Excessive drop in power line voltage.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
If either of the above should happen, you should reduce the volume
setting or shut the unit off until normal operating conditions return.
You may also want to plug the unit into a different wall outlet, as
dropping power line voltage will be most noticeable under strenuous
conditions and may result in the unit shutting down intermittently.
Troubleshooting and Service
If you should experience a problem with the operation of your
subwoofer, please check all of the following before seeking service.
Following is a simple troubleshooting guide to assist you.
1. Verify that the unit is plugged in, the power outlet is active, and
is supplying proper voltage.
2. Is unit receiving an input signal from your source?
3. Have all controls on subwoofer (volume, crossover, phase, etc.)
been properly set?
4. If unit has been running at high levels for an extended period of
time, one of the protection circuits may be engaged.
•
•
Is the built-in amplifier extremely hot to the touch?
Is your power line voltage sagging, such as when there are
other devices on the same circuit drawing lots of power?
If the protection circuitry is active, the unit may cycle on and off
until operating parameters return to normal. Under more serious
conditions, the unit may shut off completely. Normal operation should
return upon cooling, but you may be required to turn the power off
and then on again to reset the unit.
The following conditions require service by a qualified technician:
1. The power cord has become damaged.
2. The unit does not appear to operate normally or exhibits a marked
change in performance.
3. The unit has been exposed to water.
4. Some part of the cabinet or circuitry is physically damaged.
Thank You for Purchasing a Velodyne!
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
VRP-1000
VRP-1200
Cabinet Design
Bass-reflex with
Bass-reflex with
built-in power amplifier built-in power amplifier
Frequency response 35 Hz - 140 Hz
(+/-3 dB)
29 Hz - 140 Hz
(+/-3 dB)
Crossover frequency 50 - 200 Hz
(variable)
50 - 200 Hz
(variable)
Max. output power
165 watts Dynamic/
195 watts Dynamic/
115 watts RMS Power 130 watts RMS Power
Phase
0°or 180°
Input impedance
1.2K ohm
(for SPEAKER LEVEL INPUT terminals)
65K ohm
(for LINE INPUT jacks)
Sensitivity
Speaker-Level
Line
1.6V
230 mV
1.6V
230 mV
Speaker
10"
12”
(8.2" piston diameter) (9.8” piston diameter)
Power Supply
120V, 60 Hz AC
75 watts
Power consumption
Cabinet (H,W,D)
(cm)
15” x 12" x 16.75"
37.5 x 30 x 41.88
16.5” x 14.5” x 19.75”
41.25 x 36.25 x 49.38
Weight (approx.)
35 lbs. (16 Kg)
60 lbs. (27 Kg)
Specifications are subject to change without notice.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR RECORDS. . .
Date Puchased___________________________________
Dealer__________________________________________
Serial #_________________________________________
*NOTE: Please complete and return your warranty card within ten (10) days or
Register. . . ON LINE . . . It's faster . . . and easier
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
VELODYNE ACOUSTICS, Inc. (“VELODYNE”) warrants all powered subwoofers for a period of
two years, and full range speakers for a period of five years. All VELODYNE products have a
warranty from the date of purchase against defects in materials and workmanship subject to the
following conditions:
1.
VELODYNE is not responsible for defects which result from the use of an amplifier or
controller other than the one originally supplied with the unit (subwoofer) or defects which
result from modifications or repairs made by any component of the system by anyone
other than a VELODYNE factory authorized service representative.
2.
3.
This warranty is void if any repairs or service covered by the terms of this warranty are
made to any component of the system by anyone other than aVELODYNE factory autho-
rized service representative..
VELODYNE is not responsible for damage caused by accidents, abuse, misuse, natural
or personal disaster or unauthorized modification. The VELODYNE products are not in-
tended for professional or commercial use andVELODYNE is not responsible for damage
resulting from such use.
4.
5.
The VELODYNE product warranty is limited to units that are purchased from authorized
VELODYNE dealers and finalized within authorized dealer locations.
This warranty is nontransferable under any condition.
TO OBTAIN SERVICE
Information regarding service may be obtained from the dealer from whom you purchased the
unit, or by contacting VELODYNE customer service. Warranty service must be performed by a
VELODYNE factory authorized service representative within the warranty period set forth above.
If VELODYNE determines the unit is defective, VELODYNE will, at VELODYNE’s option, repair
or replace the product at no charge if the product is forwarded prepaid to a factory authorized
service representative. Products forwarded to the factory authorized service representative
should be shipped securely and properly packaged, insured, and freight prepaid.
Other VelodyneSubwooferProducts:
Digital DriveTM1812TMSignature Edition
HGS-XTMSeries
HGS-10X
Digital DriveTMSeries
HGS-12X
HGS-15X
DD-10
DD-12
DD-15
. . a n d e a s i e r
DecoSystemTM
Deco System
Deco Satellites
DD-18
c o m p l e t e a n d r e t u r n y o u r w a r r a n t y c a r d w i t h i n t e n ( 1 0 ) d a y s o r
SPLTM Series II
SPL-800 Series II
DPS SeriesTM
DPS-10
DPS-12
_ _ _ _ _ _ _ _ _ _ _ _ _ S_ P_ L_ -1_ 0_ 0_ 0_ _ S_ e_ r_ ie_ s_ I_ I_ _ _ _ _ _
SPL-1200 Series II
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
DLSTMSeries
VX-10TM
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
DLS-3500
DLS-3750
O R D S . . .
DLS-4000
Download from Www.Somanuals.com. All Manuals Search And Download.
“Not only was the little Velodyne the best small sub I’ve ever used,
it was one of the very best subs I’ve used.”
-John Potis
SoundStage!, April 2002
Velodyne Acoustics, Inc.
345 Digital Drive
Morgan Hill, CA 95037
408.465.2800 voice
408.779.9227 fax
408.779.9208 service fax
Service e-mail: [email protected]
Technical e-mail: [email protected]
Printed on recycled paper.
63-VRP1012 Rev A 28FEB04
Download from Www.Somanuals.com. All Manuals Search And Download.
|