STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed
and [OK/SEL] button simultaneously for
3 seconds. The Component LED light
will turn on for 30 seconds indicating
the unit is ready to be programmed.
STEP4 Test functions. (Same as for 3-Digit
Code Programming Method - Section
A). If any of the functions do not work as
they should, repeat from STEP 3 using
[CHꢀ] or [CHꢁ] buttons to find the
correct code.
*Note : If the 3-digit code number you just
entered is the correct number, the
Component will turn Off. If it did
not turn Off, continue entering
code numbers listed for that brand
until the Component turns Off.
STEP1 Press the [TV] button and the STEP1 Press the [CBL] button to select the CBL
TV
TV
6
Introduction
Button Functions
SYSTEM ON/OFF
Designed to send Power On/Off
commands for up to five Components
with one button press.
Set-up Code Tables
1
4
Operating Instructions For
[OK/SEL] button simultaneously for 3
seconds. The [TV] Component LED
will turn on for 30 seconds.
mode.
Manufacturer/Brand
Set-Up Code Number
Manufacturer/Brand
HITACHI
Set-Up Code Number
011 166 009 010 012 023 075 143 158 072
363 250
378 316 327 421
TM
POWER
BROCKWOOD
BROKSONIC
BYDESIGN
CANDLE
CAPEHART
CARY AUDIO DESIGN 266
CELEBRITY
CENTURION
CETRONIC
CHANGHONG
CITIZEN
CLARION
CLASSIC
CLP CLASSIC
COLORTYME
CONCERTO
CONCIERGE
CONTEC
CORNEA
CORONADO
CRAIG
116
CBL-CABLE Converters
Manufacturer/Brand
SCIENTIFIC ATLANTA 001 003 041 042 045 046
PIONEER
The CLIKR -5 UR5U-8700L-IP are
designed to operate the Scientific-Atlanta,
Pioneer, Pace Micro, Samsung and
Motorola digital set tops, plus the majority
of TV, VCR, DVD and AUDIO equipment on
the market as shown below.
STEP2 Press the [MACRO] button and [OK/SEL]
button simultaneously for 3 seconds.
The [CBL] button will turn on for 30
seconds.
Allows you to turn your TV, VCR, DVD, AUX
and Cable Box On and Off.
238
CLIKR™-5
Set-Up Code Number
031 032
116 002 003 363
058
HP
Refer to section E for details.
AUX, DVD, VCR, TV, STB
Used to select the component you want
to operate and signals remote control activity.
HUMAX
HYUNDAI
ILO
518
STEP2 Press the [VOL ꢁ] button.
001 103 034 051 063 076 105
001 005
001 030
002 111 148
MENU
337 338
Displays the Applications Menu.
STEP3 Point the remote control toward the
Component and enter the 3-digit code
number assigned to your brand.
STEP5 Save the code. (Same as for 3-Digit
PACE MICRO
SAMSUNG
MOTOROLA
STEP4 Test functions. (Same as for 3-Digit
Code Programming Method - Section
A). If any of the functions do not work
as they should, you need to find a
new code.
STEP3 Press the [TV] button again.
The Component LED will blink twice
to confirm the programming.
472
164
INFO
Cable Remote Control
001
INFINITY
INFOCUS
INITIAL
INSIGNIA
INTEQ
JANEIL
JBL
JCB
JCPENNEY
JENSEN
JVC
KAWASHO
KEC
Code Programming Method - Section A).
Displays information about the program
currently playing or highlighted in the program guide.
GUIDE
STEP3 Enter the the 2, 3 or 4-digit code for the
channel you want programmed first (for
example, 007) using the Number Pad,
then press the [STOP] button. Then
enter the code for the next channel (for
example, 050), then press the [STOP]
button. Repeat this process for the third
channel. The [CBL] button will blink
once for each channel entered.
Displays the program guide listings.
116
333 230 547 548 470
035 282
350 400 052 164 403 454 457
GENERAL INSTRUMENT 005 103 104
Now, repeat the Auto-Search Method for
those Components you could not program
earlier with the Pre-Programmed Method.
CABLE : Cable Converters
TV : Televisions
043
EXIT
OK/SELECT
HAMLIN
HITACHI
JERROLD
MAGNAVOX
MEMOREX
MOXI
PANASONIC
PHILIPS
PULSAR
RCA
REGAL
REGENCY
SONY
SPRUCER
TOCOM
TOSHIBA
VIEWSTAR
ZENITH
049 050 055
103 055
*Note : If the 3-digit code number you just
entered is correct, the Component will
turn Off. If it did not turn Off, continue
entering code numbers listed for that
brand until the Component turns Off.
Exit from current screen.
247
VCR : VCRs and TV/VCRs
DVD : DVD Players
Selects highlighted screen options.
UR5U-8700L-IP
To return to original state:
116 002 003 363 043 258 103 143
073
AUX
:
Audio Receivers and DVRs, etc.
PAGE
SETTINGS
005 004 103 005 003 008 009 010 069
043
002
Accesses pages above or below the
information currently displayed.
Displays settings menu.
STEP5 Once you have found the correct 3-
digit code, save it by pressing the
[AUX] button one more time. The
Component LED light will blink twice
to confirm the code was stored. Now
when you press the AUX button, all
If you wish to restore the CABLE channel
control in TV mode, repeat the above steps but
press [CBL] in STEP3 .
010 012
043
164
052
Replacing Batteries
Before you program or operate the remote
control, you must install two new AA alkaline
batteries.
C. Finding a Component Button’s Setup
Code Number
333
001
2
MUTE
CURSOR NAVIGATION PAD
Navigate to and highlight an item from
the on-screen choices.
Silences the audio. Press to activate.
Press again to restore sound to the
previous level.
111 252
116
024 116 008 009 030 065 258 143 333 363
044 047
363
013
STEP4 After you’ve entered the correct code
number and the Component has turned
Off, press the [POWER] button to turn
the Component back On. Now it is time
to test the VOLUME and MUTE buttons
for the TV (or PLAY and STOP buttons
for VCR and DVD) to make sure they all
work. If any of the functions do not
work as they should, repeat from STEP
3 using the next 3-digit code number
listed for that brand until you find the
best Component code.
006 012 013 020 085
073
038 034 001 083 199 210
116 001
A, B, C,
D
VOLUME
If you used the Auto-Search Method to
program a Component, you may not know
what the correct code number is. Here is a
way for you to identify the code number, so
you can record it for future reference.
Make direct selections from on-screen menus.
052
047
049 050
057
108
047
039 040 056
052
012 015
052 060 093 100
043 050 051
Raises or lowers the sound level.
G. Programming Volume Control
116
143
043
CHANNEL
Selects the next higher or lower channel.
th
FAV
the buttons will work with that 5
KENWOOD
KLEGG
KLOSS
116 001
STEP4 Press the [CHꢀ] button to store the
channels that were selected. The [CBL]
button will blink twice to confirm the
storage of commands.
STEP1 Remove the battery compartment cover
Displays favorite channels.
Volume and Mute control are factory-
programmed to automatically transfer to the
respective Component mode you select, as
follows:
Component.
043 054
466
LAST
on the back of your remote control.
ON DEMAND
002 059
CROSLEY
CROWN
164
Returns to the previously tuned channel.
Provides direct access to On Demand channel.
043 143
116 258 363 143
KMC
143
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
E. Programming the System On/Off Button
This allows you to program the System On/Off
button so it can send up to five power On/Off
commands with one button press.
INTERACTIVE
Displays the IPTV interactive.
CURTIS MATHES
CXC
CYBERHOME
DAEWOO
DAYTRON
DELL
DIMENSIA
DREAMVISION
DUKANE
DUMONT
DURABRAND
DWIN
DYNASTY
DYNEX
EIKI
ELECTROBAND
ELECTROGRAPH
ELECTROHOME
ELEKTRA
KNOLL SYSTEMS
KONKA
KREISEN
KTV
230
BACK
Takes you to the screen you visited previously.
043
015
457
STEP1 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) you want to verify
and the [OK/SEL] button simultaneously
for 3 seconds. The Component LED light
will turn on for 30 seconds.
530
FWD
To access the programmed channels, press
the [MACRO] button once. This will bring up
the first channel. Press once again and it will
bring up the second channel. Press again and
it will bring up the third channel.
CBL : CBL
T V : TV
VCR: TV
FWD ahead in stored or recorded.
363 016 043 044 076 103 114 125 127 143
363 143
320 164 363
043 116 143 154
M BUTTONS
IPTV company custom-programmable Macros.
Refer to Section H for programming steps.
STEP3 Replace the battery compartment cover.
DVD: TV
AUX: AUX
KURAZAI
LG
LITEON
LODGENET
LOEWE
LOGIK
LUXMAN
LXI
MAGNAVOX
072
VCR/DVD/VOD KEYS
Perform standard VCR and DVD functions
when in VCR and DVD mode, and Video-On-Demand
functions when in CABLE mode.
363 113 116 102 106 112 127 143
STEP1 Press the [CBL] button.
CBL-IPTV
Manufacturer/Brand
ADB
AMINO
AT&T
MYRIO
MOTOROLA
WEGENER
However, you can program the volume controls
(Volume Up, Volume Down and Mute) from one
Component to operate in another Component.
333
235
268
072
Set-Up Code Number
Replays the previous few seconds of a program.
STEP2 Press the [SYSTEM ON/OFF] button
and the [OK/SEL] button simultaneously
for 3 seconds. The [CBL] button will turn
on for 30 seconds.
STEP5 Once you have found the correct 3-digit
code, save it by pressing the same
[COMPONENT] button one more time.
The Component LED light will blink
twice to confirm that the code was
successfully stored.
NUMBER PAD
Enter numbers to tune to channels.
Also, make numeric entries on on-screen menus.
STEP2 Press the [INFO] button and count the
number of times the Component LED
light blinks. This number indicates
the first digit of the code, followed by
the second and third, each separated
by a one second pause when the LED
will turn off.
011 025
164
254 255
249
251
254 255
253
250
RECORD TV
Record a program on your TV
116 073
072
NOTE: You can also use the CH
guide as alternate ways to tune to channels.
or the program
096 052
363
I. Low Battery Warning
If you wish to store the TV volume control in
CBL mode, use the following steps.
257
166 007 138 052 251 333 164
ASPECT/
#
043
164 059 116 003 060 061 363
Changes the HD screen viewing aspect
Reserved for future use.
STEP3 Press the first [COMPONENT] button
you want to store in the [SYSTEM
ON/OFF] button and then the
[POWER] button. Repeat this for
other Components until you have
stored all the desired power
commands into the [SYSTEM
ON/OFF] button.
When the batteries are low and need to be
replaced with fresh batteries, the Component
LED lights will blink 2 times in sequence
whenever a [POWER] button is pressed to turn
on equipment.
127 022 333 094 226 390 467 431
ratio through the Cable STB.
400
STEP1 Press the [CBL] button and the
[OK/SEL] button simultaneously for 3
seconds. The [CBL] Component LED
will turn on for 30 seconds.
MAJESTIC
MARANTZ
MATSUI
MATSUSHITA
MAXENT
MEGATRON
MEMOREX
MGA
MIDLAND
MINTEK
MINUTZ
MISAKAI
MITSUBISHI
MONIVISION
MONTGOMERY WARD 333 072
MOTOROLA
MTC
MULTITECH
NAD
NEC
333 072
116 164 281
187
ON-OFF
-
PIP CH +/
Selects the next higher or lower channel
in the PIP (Picture-In-Picture) window
through the Cable STB.
Opens or closes the PIP (Picture-In-Picture)
window through the Cable STB.
001
Now, program the rest of your Components by
repeating STEPS 1-5.
164
466
TV
VIDEO SOURCE
Selects the video source from available
video Components through the Cable STB.
080
*Note : 10 blinks represents the number zero.
143 024 076 196
MOVE
Manufacturer/Brand
Set-Up Code Number
112 143
025
036
072 251 333
247 388
002
103
Moves the PIP (picture-In-Picture) window to
another location on the screen through the
Cable STB.
242
072
*Note : If the Pre-Programmed Method did not
work, or if the Code Tables do not list
your Component brand, use the Auto-
Search Method as explained in Section B.
Example : One blink, (pause), eight blinks,
(pause) and three blinks, indicates
code number 183.
116 011
007 072 363
116 363 024 028 042
333 073
A MARK
ABEX
ACCURIAN
ADMIRAL
ADVENT
ADVENTURA
AIKO
AKAI
ALBATRON
ALERON
AMERICA ACTION 043
AMPRO
AMSTRAD
ANAM
AOC
APEX DIGITAL
ASTAR
ELEMENT
EMERSON
363 494 526
SWAP
STEP2 Press the [VOL ꢀ] button.
LIGHT BUTTON
Press to backlight all keypad buttons.
Press again to turn off (or simply wait 10 seconds
for automatic shut-off).
028 048 043 155 005 116 363 047 050 051
Swaps the contents of the PIP (Picture-In-Picture) window
and the main viewing screen through the Cable STB so that
the PIP window displays on the main screen.
J. Memory Lock System
076 096 143 153 154 052 514
STEP3 Press the [TV] button.
The Component LED will blink twice
to confirm the programming.
ENVISION
EPSON
ESA
FISHER
FUJITSU
FUNAI
116
STEP4 Press the [CHꢀ] button to save the
power commands you stored. The
[CBL] button will blink twice to
confirm the commands have been
saved.
th
This remote control is designed to retain
programmed memory for 10 years even after
batteries are removed from the remote control.
324
362
D. AUX Function: Programming a 5
Component
Operations
3
008
323
B. Auto-Search Method
Programming the Remote Control
There are two ways you can program your CLIKR -5 remote:
5
007 057
052
246 198 410
124 109 024 028 040 042 146 363 348
017
116 146 248 404 405 473 475 323 387 391
017
028
STEP1 Turn on the Component you want to
DEFAULT STATE:
TM
To return to original state:
You can take advantage of the AUX function to
028 043 052
program (TV, VCR, DVD or AUX).
Component Default: CABLE Set Top Box (STB)
Channel Default: CABLE channel and numbers
through the CABLE STB. You have the option of
controlling your CABLE channel and numbers
through the TV or VCR. Refer to section F for
programming steps.
th
program a 5 Component such as a second
FUTURETECH
GATEWAY
GE
043
If you wish to restore the CBL volume control
in CBL mode, repeat the above steps but press
[CBL] in STEP3 .
The Pre-Programmed 3-Digit Code Method
*
K. Record Your Component Set-up Codes
242 268
081
STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed
and [OK/SEL] button simultaneously for
3 seconds. The Component LED light
will turn on for 30 seconds indicating
the unit is ready to be programmed.
TV, VCR, DVD or Audio Component.
The Auto-Search Method
*
073 116 008 009 034 056 074 155 333 363
116 363 258
073
052
F. Programming Channel Control
th
TV
Set-up Code Number:
STEP1 Turn on the 5 Component you want
GEM
391
043
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
code numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
Auto-Search Method scans through all the codes in the remote control, one at a time.
You can program the channel controls
(Channel Up, Channel Down, Last and
Numbers) from one Component to operate in
another Component mode. Default channel
control settings on the remote control are as
follows:
GIBRALTER
GO VIDEO
GOLDSTAR
GRUNPY
HAIER
116 073
138 025
043 054 056 080 112
116 363 112 058
006
477
076 454 388
052
to program (TV, VCR, DVD or Audio).
VCR Set-up Code Number:
DVD Set-up Code Number:
AUX Set-up Code Number:
026
272 197134 116 040 016 024 056 019 262
STEP2 Press the [AUX] button and the
[OK/SEL] button simultaneously for 3
seconds.The [AUX] Component LED
will turn on for 30 seconds.
236 281
242
113 116 102 363 106 112 127 143
H. Programming a ‘Macro’ button.
NET TV
NIKEI
NIKKO
NIKO
Volume Default: Volume and Mute control are
automatically transferred to the respective
Component mode you select, as follows: CBL:
Cable Set Top Box / TV: TV / AUX: AUX. Volume
and Mute control for VCR and DVD are
automatically transferred to the TV. However,
you have the option of controlling CABLE
Volume and Mute through the TV, VCR or AUX.
Refer to section G for programming steps.
028 043
363 501
363
If your remote model has custom-programmable
Macro buttons available, they can be
programmed to act as a 'Macro' or Favorite
Channel button in CABLE mode. This allows you
to program up to five 2-digit channels, four 3-digit
channels or three 4-digit channels that can be
accessed with one button press.
043
AUDIOVOX
AVENTURA
AVION
IMPORTANT SETUP NOTE!
STEP3 Point the remote toward the Component
and press the [CHꢀ] or [CHꢁ] button
one step at a time or keep it pressed.
The remote will emit a series of ON/OFF
commands. Release the [CHꢀ] or
[CHꢁ] button as soon as the Component
turns Off.
116
HALL MARK
HANNSPREE
HARLEY DAVIDSON 028
This pertains to all programming steps. When you are in setup mode, a component LED will
light for 30 seconds.If you do not press a button within 30 seconds, the LED light will turn off
and exit setup mode and you will need to start over.
527
349 381
441
039
NORCENT
390
AXION
STEP3 Press the [COMPONENT] button you
want to setup. Point the remote control
toward the Component and enter the 3-
digit code number assigned to your
brand.
CBL : CBL
T V : CBL
VCR: CBL
NORWOOD MICRO 027
HARVARD
HAVERMY
HELLO KITTY
HIMITSU
043
BELCOR
BELL&HOWELL
BENQ
BOXLIGHT
BRADFORD
116
333 072
423
266
043
NTC
103
081
DVD: DVD
AUX: AUX
Universal Remote Control, Inc.
NUVISION
OLEVIA
ONKING
351
432 363 333
043
076
043
419 442
A. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX).
If you wish to store the TV channel control in
TV mode, use the following steps.
OCE-0060G REV 01 (06/30/08)
HISENSE
Download from Www.Somanuals.com. All Manuals Search And Download.
|