STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
seconds. The Component LED light will
turn on for 30 seconds indicating the unit
is ready to be programmed.
STEP3 Point the remote control toward the
Component and enter the 3-digit code
number assigned to your brand.
STEP5 Save the code. (Same as for 3-Digit Code
STEP5 Once you have found the correct 3-digit
code, save it by pressing the [AUX] button
one more time. The Component LED light
will blink twice to confirm the code was
stored. Now when you press the AUX
CBL : TV
T V : TV
VCR : TV
Introduction
Button Functions
4
1
Programming Method - Section A).
Operating Instructions For
DVD : TV
AUX : AUX
TM
Now, repeat the Auto-Search Method for those
Components you could not program earlier
with the Pre-Programmed Method.
The CLIKR -5 UR5U-8500 is designed to
operate Scientific-Atlanta, Pioneer, Voyager
and Pace Micro digital set top boxes
(including DVR & HD), plus the majority of TV,
VCR, DVD and AUDIO equipment on the
market as shown below.
If you wish to store the CBL volume control in CBL
mode, use the following steps.
STEP1 Press the [CBL] button and the [OK/SEL]
button simultaneously for 3 seconds. The
[CBL] Component LED will turn on for 30
seconds.
CLIKR™-5
th
button, all the buttons will work with that 5
Component.
C. Finding a Component
Cable Remote Control
E. Programming the System On/Off Button
This allows you to program the System On/Off button
so it can send up to five power On/Off commands
with one button press.
Button’s Setup Code Number
CABLE : Cable Converters
TV : Televisions
*Note : If the 3-digit code number you just entered
is correct, the Component will turn Off. If it
did not turn Off, continue entering code
numbers listed for that brand until the
Component turns Off.
STEP2 Press the [VOL +] button.
If you used the Auto-Search Method to program a
Component, you may not know what the correct code
number is. Here is a way for you to identify the code
number, so you can record it for future reference.
VCR : VCRs and TV/VCRs
DVD : DVD Players
UR5U-8500
STEP3 Press the [CBL] button.
The Component LED will blink twice to
confirm the programming.
AUX : Audio Receivers and DVRs, etc.
STEP1 Press the [CBL] button.
STEP2 Press the [SYSTEM ON/OFF] button and the
[OK/SEL] button simultaneously for 3
seconds. The [CBL] button will turn on for
30 seconds.
STEP3 Press the first [COMPONENT] button you
want to store in the [SYSTEM ON/OFF]
button and then the [POWER] button.
Repeat this for other Components until you
have stored all the desired power
commands into the [SYSTEM ON/OFF]
button.
Replacing Batteries
2
STEP1 Press the [COMPONENT] button (TV, VCR,
DVD or AUX) you want to verify and the
[OK/SEL] button simultaneously for 3
seconds. The Component LED light will turn
on for 30 seconds.
To return to original state:
If you wish to restore the TV volume control in CBL mode,
repeat the above steps but press [TV] in STEP3
STEP4 After you’ve entered the correct code
number and the Component has turned
Off, press the [POWER] button to turn the
Component back On. Now it’s time to test
the VOLUME and CHANNEL buttons for
the TV (or PLAY and STOP buttons for
VCR and DVD) to make sure they all work.
If any of the functions do not work as they
should, repeat from STEP 3 using the next
3-digit code number listed for that brand.
STEP5 Once you have found the correct 3-digit
code, save it by pressing the same
[COMPONENT] button one more time.
The Component LED light will blink twice
to confirm that the code was successfully
stored.
Before you program or operate the remote
control, you must install two new AA alkaline
batteries.
.
H. Programming a ‘Macro’ or Favorite
Channel
In CBL mode, the M1, M2, HELP and BLANK
buttons can be programmed to act as a ‘Macro’ or
Favorite Channel button. This allows you to send
up to 10 commands with one button press.
STEP1 Remove the battery compartment cover
STEP2 Press the [INFO] button and count the
number of times the Component LED light
blinks. This number indicates the first digit
of the code, followed by the second and
third, each separated by a one second
pause when the LED will turn off.
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP4 Press the [CH+] button to save the power
commands you stored. The [CBL] button
will blink twice to confirm the commands
have been saved.
STEP3 Replace the battery compartment cover.
STEP1 Press the [CBL] button to select the CBL
*Note :10 blinks represents the number zero.
mode.
Example : One blink, (pause), eight blinks, ( pause)
and three blinks, indicates code number
183.
STEP2 Press the M1, M2, HELP or BLANK button
and [OK/SEL] button simultaneously for 3
seconds. The [CBL] Component LED will
turn on for 30 seconds.
STEP3 Press up to 10 buttons you wish to store.
The [CBL] Component LED will blink once
for each command entered.
STEP4 Press the [CH+] button to store the
commands that were selected. The [CBL]
Component LED will blink twice to
confirm the storage of commands.
F. Programming Channel Control
Now, program the rest of your Components
by repeating STEPS 1-5.
th
You can program the channel controls (Channel Up,
Channel Down and Last) from one Component to
operate in another Component mode. Default channel
control settings on the remote control are as follows:
D. AUX Function: Programming a 5
Component
*Note : If the Pre-Programmed Method did not
work, or if the Code Tables do not list your
Component brand, use the Auto-Search
Method as explained in Section B.
You can take advantage of the AUX function to
th
program a 5 Component such as a second TV, VCR,
CBL : CBL
T V : CBL
VCR : CBL
DVD or Audio Component.
DVD : DVD
AUX : AUX
th
STEP1 Turn on the 5 Component you want to
B. Auto-Search Method
STEP1 Turn on the Component you want to
program (TV, VCR, DVD or AUX) using
your old remote.
If you wish to store the TV channel control in TV
mode, use the following steps.
STEP1 Press the [TV] button and the [OK/SEL]
button simultaneously for 3 seconds. The
[TV] Component LED will turn on for 30
seconds.
STEP2 Press the [VOL -] button.
STEP3 Press the [TV] button again.
The Component LED will blink twice to
confirm the programming.
program (TV, VCR, DVD or Audio) using
your old remote.
I. Low Battery Warning
STEP2 Press the [AUX] button and the [OK/SEL]
button simultaneously for 3 seconds.The
[AUX] Component LED will turn on for 30
seconds.
When the batteries are low and need to be
replaced with fresh batteries, the Component LED
lights will blink 2 times in sequence whenever a
[POWER] button is pressed to turn on equipment.
STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
seconds. The Component LED light will
turn on for 30 seconds indicating the unit
is ready to be programmed.
STEP3 Point the remote toward the Component
and press the [CHꢀ] or [CHꢁ] button
one step at a time or keep it pressed. The
remote will emit a series of ON/OFF
commands. Release the [CHꢀ] or
[CHꢁ] button as soon as the Component
turns Off.
Programming the Remote Control
5
TM
There are two ways you can program your CLIKR -5 remote:
Operations
3
STEP3 Press the [COMPONENT] button you want
to setup. Point the remote control toward
the Component and enter the 3-digit code
number assigned to your brand.
The Pre-Programmed 3-Digit Code Method
The Auto-Search Method
*
*
DEFAULT STATES:
Component Default: CABLE
Channel Default: CABLE channel and number
keys through the CABLE. You have the option
of controlling your CABLE channel and
number keys through the TV or VCR. Refer to
section F for programming steps.
Volume Default: TV volume and mute keys
through the TV. You have the option of
controlling your TV volume and mute through
the Cable box, VCR or DVD. Refer to section G
for programming steps.
J. Memory Lock System
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
code numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
Auto-Search Method scans through all the codes in the remote control, one at a time.
This remote control is designed to retain
programmed memory for 10 years even after
batteries are removed from the remote control.
To return to original state:
*Note : If the 3-digit code number you just entered is
the correct number, the Component will turn
Off. If it did not turn Off, continue entering
code numbers listed for that brand until the
Component turns Off
If you wish to restore the CABLE channel control in
TV mode, repeat the above steps but press [CBL]
IMPORTANT SETUP NOTE!
in STEP3
.
K. Record Your Component Set-up Codes
This pertains to all programming steps. When you are in setup mode, a component LED will light for
30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit setup
mode and you will need to start over.
G. Programming Volume Control
TV
Set-up Code Number:
Set-up Code Number:
Set-up Code Number:
Set-up Code Number:
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section A). If any
of the functions do not work as they
should, repeat from STEP 3 using [CHꢀ]
or [CHꢁ] buttons to find the correct code.
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section A). If any
of the functions do not work as they should,
you need to find a new code.
VCR
DVD
AUX
You can program the volume controls (Volume Up,
Volume Down and Mute) from one Component to
operate in another Component mode. Default volume
control settings on the remote control are as follows:
Universal Remote Control, Inc.
A. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) using your old remote.
OCE-0045A REV 02 (05/06/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
|