TM
*Note : 10 blinks represents the number zero.
STEP3 Point the remote control toward the
Component and enter the 3-digit code
number assigned to your brand.
*Note : If the 3-digit code number you just entered is
correct, the Component will turn Off. If it did not
turn Off, continue entering code numbers listed
for that brand until the Component turns Off.
STEP2 Line up the CLIKR -5 to the other remote,
STEP2 Press the [VOL
ꢁ
] button.
Introduction
Button Functions
4
1
head-to-head, 1 or 2 inches apart.
Operating Instructions For
Example : One blink, (pause), eight blinks, ( pause) and
STEP3 Press the [TV] button again. The Component
TM
three blinks, indicates code number 183.
STEP3 Press any button on the CLIKR -5 that you
TM
LED will blink twice to confirm the programming.
The CLIKR -5 UR5L-8520 is designed to
operate all Scientific-Atlanta, Pioneer
Voyager and Pace Micro digital set top
boxes (including DVR & HD), plus the
majority of TV, VCR, DVD and AUDIO
equipment on the market as shown below.
th
want to teach a command to. For example,
if you want to teach the [MUTE] button,
press the [MUTE] button.
G. AUX Function: Programming a 5 Component
™
To return to original state:
If you wish to restore the CABLE channel control in TV
th
You can take advantage of the AUX function to program a 5
Component such as a second TV, VCR, DVD or Audio Component.
CLIKR -5
mode, repeat the above steps but press [CBL] in STEP3
.
STEP4 Press and hold the [MUTE] button on the
TM
th
STEP4 After you’ve entered the correct code number
and the Component has turned Off, press the
[POWER] button to turn the Component back
On. Now it’s time to test the VOLUME and
MUTE buttons for the TV (or PLAY and STOP
buttons for VCR and DVD) to make sure they all
work. If any of the functions do not work as they
should, repeat from STEP 3 using the next 3-digit
code number listed for that brand.
STEP5 Once you have found the correct 3-digit code,
save it by pressing the same [COMPONENT]
button one more time. The Component LED
light will blink twice to confirm that the code
was successfully stored.
other remote until the CLIKR -5 Component
STEP1 Turn on the 5 Component you want to program
Cable Remote Control
J. Programming Volume Control
LED light blinks twice.
(TV, VCR, DVD or Audio) using your old remote.
You can program the volume controls (Volume Up,
Volume Down and Mute) from one Component to
operate in another Component mode. Default volume
control settings on the remote control are as follows:
CABLE : Cable Converters
TV : Televisions
*Note : The LED will blink 5 times if there was an
error in the learning process. In so, repeat
STEPS 3 and 4. Continue learning other
buttons by repeating STEPS 3 and 4.
STEP2 Press the [AUX] button and the [OK/SEL] button
simultaneously for 3 seconds.The [AUX]
Component LED will turn on for 30 seconds.
VCR : VCRs and TV/VCRs
DVD: DVD Players
UR5L-8520L
AUX : Audio Receivers and DVRs, etc.
STEP3 Press the [COMPONENT] button you want to
setup. Point the remote control toward the
Component and enter the 3-digit code number
assigned to your brand.
CBL : TV
T V : TV
VCR : TV
STEP5 Once you have completed teaching
DVD : TV
AUX : AUX
Replacing Batteries
2
TM
CLIKR -5 all desired commands for that
If you wish to store the CBL volume control in CBL mode,
use the following steps.
Component, save the learned commands by
pressing the [COMPONENT] and [ # ]
buttons simultaneously until the Component
LED blinks 3 times. Now test all the buttons
to make sure they learned correctly.
Before you program or operate the remote
control, you must install two new AA alkaline
batteries.
*Note :If the 3-digit code number you just entered is the
correct number, the Component will turn Off. If it
did not turn Off, continue entering code numbers
listed for that brand until the Component turns Off.
STEP1 Press the [CBL] button and the [OK/SEL] button
simultaneously for 3 seconds. The [CBL]
Component LED will turn on for 30 seconds.
STEP1 Remove the battery compartment cover
STEP2 Press the [VOL
ꢀ] button.
on the back of your remote control.
Now, program the rest of your Components by
repeating STEPS 1-5
*Note : If the Pre-Programmed Method did not
work, or if the Code Tables do not list your
Component brand, use the Auto-Search
Method as explained in Section B.
D. Erasing a Single Learned Command
STEP1 Press the [COMPONENT] and [ # ]
buttons simultaneously for 3 seconds
until the Component LED light turns on.
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section A). If any of
the functions do not work as they should, you
need to find a new code.
STEP3 Press the [CBL] button. The Component LED
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
will blink twice to confirm the programming.
To return to original state:
If you wish to restore the TV volume control in CBL mode,
STEP5 Once you have found the correct 3-digit code,
save it by pressing the [AUX] button one more
time. The Component LED light will blink twice
to confirm the code was stored. Now when
you press the AUX button, all the buttons will
STEP2 Press and hold the button you want to erase
for 3 seconds. The Component LED will blink
twice to confirm the erasure.
STEP3 Replace the battery compartment cover.
repeat the above steps but press [TV] in
.
STEP3
B. Auto-Search Method
STEP1 Turn on the Component you want to
program (TV, VCR, DVD or AUX) using your
old remote.
K. Programming a ‘Macro’ or Favorite Channel
STEP3 To exit, press and hold both the
th
In CBL mode, the M1, M2 and HELP buttons can be
programmed to act as a ‘Macro’ or Favorite Channel
button. This allows you to send up to 10 commands with
one button press.
[COMPONENT] and
[
#
]
buttons
work with that 5 Component.
simultaneously until the Component LED
blinks 3 times.
H. Programming the System On/Off Button
This allows you to program the System On/Off button so it can
send up to five power On/Off commands with one button press.
STEP2 Press the [COMPONENT] button (TV, VCR,
DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
seconds. The Component LED light will turn
on for 30 seconds indicating the unit is ready
to be programmed.
E. Erasing All Learned Commands from One Component
STEP1 Press the [COMPONENT] and [ # ] buttons
simultaneously for 3 seconds until the
Component LED light turns on.
STEP1 Press the [CBL] button to select the CBL mode.
STEP1 Press the [CBL] button.
STEP2 Press the [M1,M2 or HELP] button and [OK/SEL]
button simultaneously for 3 seconds. The [CBL]
Component LED will turn on for 30 seconds.
STEP2 Press the [SYSTEM ON/OFF] button and the
[OK/SEL] button simultaneously for 3 seconds.
The [CBL] button will turn on for 30 seconds.
STEP2 Press and hold both the [COMPONENT]
button you want to erase and the [PAUSE]
button for 3 seconds. The Component LED
will blink twice to confirm the erasure.
STEP3 Press up to 10 buttons you wish to store. The
[CBL] Component LED will blink once for each
command entered.
STEP3 Point the remote toward the Component and
press the [CHꢀ] or [CHꢁ] button one step
at a time or keep it pressed. The remote will
emit a series of ON/OFF commands.
Release the [CHꢀ] or [CHꢁ] button as soon
as the Component turns Off.
STEP3 Press the first [COMPONENT] button you want
to store in the [SYSTEM ON/OFF] button and
then the [POWER] button. Repeat this for other
Components until you have stored all the
desired power commands into the [SYSTEM
ON/OFF] button.
STEP4 Press the [CH ] button to store the commands
ꢀ
STEP3 To exit, press and hold both the
that were selected. The [CBL] Component LED
will blink twice to confirm the storage of
commands.
Programming the Remote Control
There are three ways you can program your CLIKR -5 remote:
5
[COMPONENT] and
[
#
]
buttons
TM
simultaneously until the Component LED
blinks 3 times.
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section A). If any of
the functions do not work as they should,
repeat from STEP 3 using [CHꢀ] or [CHꢁ]
buttons to find the correct code.
The Pre-Programmed 3-Digit Code Method
The Auto-Search Method
*
*
STEP4 Press the [CHꢀ] button to save the power
L. Low Battery Warning
F. Finding a Component Button’s Setup Code Number
commands you stored. The [CBL] button will
blink twice to confirm the commands have
been saved.
Operations
The Learning Method
3
*
When the batteries are low and need to be replaced with
fresh batteries, the Component LED lights will blink 2
times in sequence whenever a [POWER] button is
pressed to turn on equipment.
If you used either the Auto-Search or Learning
Methods to program a Component, you may not know
what the correct code number is. Here is a way for
you to identify the code number, so you can record it
for future reference.
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers
that correspond to a particular Component’s manufacturer/brand, so it’s the fastest and easiest of the three
methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-Search Method scans through all
the codes in the remote control, one at a time. The Learning Method allows you to transfer functions from other
remotes, one button at a time.
DEFAULT STATE:
Component Default: CABLE
Channel Default: CABLE channel and
numbers operate through the CABLE. You
have the option of controlling channel and
numbers through the TV, VCR or DVD. Refer
to section I for programming steps.
Volume Default: CABLE volume and mute
operate through the TV. You have the option
of controlling volume and mute through the
Cable box, VCR or DVD. Refer to section J J
for programming steps.
I. Programming Channel Control
STEP5 Save the code. (Same as for 3-Digit Code
You can program the channel controls (Channel Up,
Channel Down and Last) from one Component to
operate in another Component mode. Default channel
control settings on the remote control are as follows:
Programming Method - Section A).
M. Memory Lock System
This remote control is designed to retain programmed
memory for 10 years even after batteries are removed
from the remote control.
Now, repeat the Auto-Search Method for those
Components you could not program earlier with the
Pre-Programmed Method. If you can’t find the right
code using the Auto-Search Method, try the Learning
Method in Section C.
IMPORTANT SETUP NOTE!
STEP1 Press the [COMPONENT] button (TV, VCR, DVD
or AUX) you want to verify and the [OK/SEL]
button simultaneously for 3 seconds. The
Component LED light will turn on for 30 seconds.
This pertains to all programming steps. When you are in setup mode, a component LED will light for 30 seconds.If
you do not press a button within 30 seconds, the LED light will turn off and exit setup mode and you will need to
start over.
CBL : CBL
T V : CBL
VCR : CBL
N. Record Your Component Set-up Codes
DVD : DVD
AUX : AUX
TV
Set-up Code Number:
Set-up Code Number:
Set-up Code Number:
Set-up Code Number:
STEP2 Press the [INFO] button and count the number of
times the Component LED light blinks. This
number indicates the first digit of the code,
followed by the second and third, each
separated by a one second pause when the LED
will turn off.
A. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) using your old remote.
If you wish to store the TV channel control in TV mode,
use the following steps.
C. The Learning Method
VCR
DVD
AUX
STEP1 Press the [COMPONENT] button (TV, VCR,
DVD or AUX) to be programmed and the [ # ]
buttons simultaneously for 3 seconds until
the Component LED light turns on.
Universal Remote Control, Inc.
STEP1 Press the [TV] button and the [OK/SEL] button
simultaneously for 3 seconds. The [TV]
Component LED will turn on for 30 seconds.
STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and [OK/SEL] button
simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is
ready to be programmed.
OCE-0045K REV 03(04/14/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
|