OCE-0030A_UR2CBLCV04_Rev23 2012.2.7 6:19 PM 페이지1
STEP3 Point the remote control toward the TV and
enter the three-digit code number assigned
to your brand from the code tables.
Introduction
Button Functions
3
1
Operating Instructions
For CABLEVISION
Remote Control
The remote control is designed to operate the
Scientific-Atlanta Explorer 8000, Pioneer
Voyager DVR and the Pace Micro DVR Series
set top boxes and the majority of TV's on the
market.
*Tip : The TV will turn off when the correct three-
digit code number has been entered. You
can verify you have selected the correct
code by pressing the [MUTE] button, the TV
should turn on or turn off.
UR2-CBL-CV04
Replacing Batteries
Before you program or operate the remote control,
you must install two AA alkaline batteries.
*Note : If there is more than one three-digit number
listed for your brand, try one code number at a
time until your TV turns off.
2
STEP4 Store the three-digit code number by press-
ing the [TV] button once again. The iO button
will blink twice to confirm that the code has
been stored.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the illus-
tration below.
*Note : Try all the functions on the remote control. If
any of the functions do not work as they
should, repeat from Step 2 using the next three-
digit code number from the same brand list.
STEP3 Replace the battery compartment cover.
B. Auto Search Method.
If the three-digit code numbers assigned to your
brand do not turn off your TV or the code tables
do not list your brand, you can use the Auto
Search Method to find the correct three-digit
code number for your TV by the following steps:
STEP1 Turn on the TV you wish to operate.
STEP2 Press the [TV] button and the [SEL] button
simultaneously for 3 seconds.
The iO button will turn on.
*Tip : The iO button will light on for 20 seconds.
The next step must be entered while the iO
button is on.
STEP3 Press the [CHꢀ] or [CHꢁ] button one step
at a time or keep it pressed. The remote will
emit a series of Power ON/OFF commands.
Release the [CHꢀ] or [CHꢁ] button as soon
as the TV turns off.
Operations
4
Programming the Remote Control.
5
*Tip : You can verify that you selected the correct
code by pressing the [MUTE] button. The TV
should either turn on or turn off.
Default State :
Device Default: Scientific-Atlanta Explorer
8000
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three digit code number that corre-
sponds to particular manufacturers and brands of TV.
The three-digit code numbers are listed in the code table of the instruction manual.
STEP4 Press the [TV] button to store the code. The
iO button will blink twice to confirm that the
code has been stored.
Volume Default : TV volume and mute through
the TV, with the option of controlling volume
and mute through the Cable. Refer to Section D
for programming the volume and mute through
your Cable.
STEP1 Turn on the TV you wish to program.
C. To Find the Three Digit Code Number
That was Stored in the TV.
STEP1 Press the [TV] button and the [SEL] button
STEP2 Press the [TV] button and the [SEL] button simultaneously for 3 seconds. The iO button
will turn on indicating the unit is ready to be programmed.
Universal Remote Control, Inc.
*Tip : The iO button will light on for 20 seconds. The next step must be entered while the iO button is on.
simultaneously for 3 seconds.
OCE-0030A Rev 23(01/20/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
|