Congratulations on your purchase of the Uniden
GMR2889-2CK (General Mobile Radio Service)
radio. This lightweight, palm-sized, radio is a state-
of-the-art device, equipped with many valuable
features. Use it at sporting events, to stay in
contact with family and friends, hiking, skiing,
outdoors, or in a neighborhood watch for vital
communication.
3) Put the NiMH battery pack in the battery
compartment applying the battery contacts to
the lower charge contacts. Be sure to follow the
instructions written on the battery pack’s label.
Installing the battery pack incorrectly will prevent
the unit from operating.
•
•
•
•
Do not recharge alkaline batteries. Doing so can
create a safety hazard or damage the radio.
Setting Your Nickname
Automatically Changing Channels
Channel Scan Feature
Navigating through the Normal Menu
Setting Silent Mode
SETTING UP GROUP MODE
GMR2889-2CK
Your nickname appears on other units’ displays
when you make a All Call or direct call. This is also
the name that appears on other radio displays
when someone wants to make a direct call to you.
When no nickname is set, the unit number appears.
Auto Channel Change lets you easily coordinate a
channel change for everyone in your group. You
might want to do this when you find you are getting
a lot of interference on your current channel. Or,
you can use this feature to change from a low-
power channel (8-14) to one of the high-powered
channels (1-7, 15-22) if you need more range (or to
a low-power channel if you need longer battery
life).
Your radio has a channel scan feature that lets you
easily scan all 22 channels. When an active
channel is detected, the radio pauses on that
channel until the channel is clear. Then after a 2-
second delay, the radio resumes scanning.
Pressing PTT or Power boost while the scan is
paused on a channel lets you transmit on that
channel.
To access the advanced features of your radio has
a Menu function.
When you turn on the silent mode, all incoming calls
are muted: the radio blinks the display backlight, the
channel indicator, SLNT and call to alert you to an
incoming call. If you do not respond to the call within
15 seconds, the backlight turns off, and the call will
blink until there is no signal. Silent mode is disabled
for 15 seconds when you transmit, receive, or press
any other button.
In order to use Group Mode you need to initialize a
couple of settings in your radio:
For fastest charging, turn off the radio before
charging.
•
•
15 GMRS / 7 FRS Channels
142 Privacy Codes (CTCSS Tone
and DCS Code)
•
Power Boost Button for
Maximum Range
All Call
VOX Level
Call Tone
Silent Mode
Key Lock
•
•
•
•
•
•
•
•
•
Batteries must be installed for operation, even
from external power.
• Set the radio to Group Mode
• Set a Group Code
• Set a Ring Tone
• Set a Unit Number
• Set a "Nickname"
•
•
•
•
•
•
•
•
•
•
Up to 28 Mile Range*
Direct Call
Auto Channel Change Call
Battery Charger
Battery Level Meter
Channel Monitor
Channel Scan
Group Scan
Keypad Lock
NOAA Emergency /
Weather Channels
Emergency Weather Alert
DC IN 9V Jack
4) Replace the battery compartment door.
If battery power is low, you cannot operate the
radio even using external power. Let the
batteries charge before using. If you try to
transmit while power is low, the radio
automatically turns off.
1-10
OFF, 1-5
ON-OFF
ON-OFF
1) Press and hold menu/grp for 2 seconds, then
tap menu/grp four times until the radio displays
143 Group Codes
Silent Mode
Internal VOX Circuitry
10 Selectable Call/Ring Tone Alerts
Backlit LCD Display
Optional Headset Accessories
Headset Jack
n
place in the nickname flashing.
(or your current nickname) with the first
1) To enter the menu, press menu/grp.
2) Additional presses of menu/grp advances you
through the menu. After the last menu item, the
radio exits to the previous mode.
3) Other ways to exit the Menu function are:
a. Press PTT, Power boost, mon, d-call,
wx/alert, or ch tone/scn.
- - - -
To turn on channel scan:
To set the silent mode:
USING THE RADIO BATTERY
LEVEL AND LOW BATTERY ALERT
Press and hold ch tone/scn until SCAN appears.
The channel number changes as the radio rapidly
cycles through the channels.
1) Enter the menu. Advance through the menu until
the SLNT appears. The current setting flashes.
2) Press L to display on SLNT.
2) Press L or M to select the letter, then ch
tone/scn to advance to the next letter until you
have entered your nickname.
3) Press menu/grp to confirm the setting and exit
the group settings menu.
To start an auto channel change, on any radio in
the group tap ch tone/scn twice. The current
channel and CHCX appears. Use L or M to select
the target channel. You can check whether the
selected channel is clear. Then press d-call.
Your radio chirps for about 10 seconds while it
sends out the channel change signal. As each
radio receives the channel change signal, it chirps
once, then changes to the new channel.
PACKAGE CONTENTS
Setting the Radio to Group Mode
Your package contains two radios, two rechargeable
NiMH battery packs (#BT-1013), one AC adapter
(#AD-314), one charging cradle (#RC1281), two belt
clips and this reference guide. You can operate the
unit using the rechargeable NiMH battery pack or 4
AAA alkaline batteries (not included).
To order the following optional accessories, visit our
during business hours.
To set the radio to Group Mode, which enables
Direct Call, Auto Channel Change and All Call,
press and hold menu/grp for 2 seconds. The radio
displays oF GRUP. Press L to display on GRUP,
then press menu/grp to advance to setting the
Group Code.
This radio has a battery level meter that indicates
the status of the batteries. When the battery level is
low, BATT appears and the battery level meter icon
flashes. Recharge the NiMH battery pack
immediately or, if you are using the alkaline
batteries, replace the alkaline batteries in order to
continue using the radio.
Roger Beep
•
•
Note: To prevent unwanted silent alerts, be sure to
use a Privacy code or group code whenever you use
the Silent mode feature.
You can hear the received voice when you turn on
channel scan and an active channel is detected
even during silent mode.
To turn off channel scan:
b. Wait 10 seconds until the radio automatically
returns to the previous mode.
Press d-call, PTT, Power boost, wx/alert or
menu/grp, or press and hold ch tone/scn for 2
seconds.
USING THE RADIO
Using Group Mode
Group mode lets you make direct calls to other
people in your group without alerting the entire
group and also lets you quickly change everyone in
your group to another channel from a single radio.
Before using group mode, follow the instructions in
"Setting Up Group Mode" on every radio in your
group. Then, to record the unit ID and everyone’s
nickname in every radio, send a call to "All" from
each radio one time (see "Sending a Direct Call").
In order to get the most out of your new radio, read
this reference guide completely before attempting to
operate the unit.
Voice Operated Transmission
Note: In group mode, you cannot receive
transmissions from other radios unless they are
also set to the same channel and group code.
Your radio has a user selectable Voice Operated
Transmitter (VOX) that can be used for automatic
voice transmissions. The VOX feature is designed
to be used with a headset with a microphone.
Transmission is starts when you speak into the
microphone instead of pushing the PTT and Power
boost button.
Talking on Your Radio
To ensure all radios make it to the new channel, we
recommend you:
Warning! To avoid the risk of personal injury or
property damage from fire or electrical shock, only
use the Uniden accessories specifically designated
for this product.
Use only Uniden accessories.
Missed Call Alerts
Turning the Radio On and Adjusting the Volume
To talk to others using the radio:
• NiMH Battery Pack - #BT-1013
• Charging Cradle - #RC1281
• VOX Headset - #HS910/HS915/ZA-133
• AC Adapter - #AD-314
If you receive an incoming call while silent mode is
on and do not respond, the radio will turn on the
Missed Call icon. If you are using the Group Mode,
the radio will also indicate the person who made the
call.
1) Rotate vol/off clockwise until it clicks, and set
volume to a comfortable listening level.
2) To turn off the radio, rotate vol/off
counterclockwise until it clicks.
1) Press and hold PTT or Power boost and speak
in a clear, normal voice about 2-3 inches away
from the microphone. While you transmit, TXHI
or TXLO appears on the display according to
the type of channel. To avoid cutting off the first
part of your transmission, pause slightly after
pressing PTT or Power boost before you start
talking.
Setting the Group Code
• Make sure you are in an open environment,
where the radio will get the best range.
• Optimize range during the channel change
signal by raising the radio over your head to give
the best possible height.
*Range may vary depending on environmental and/or topographical conditions.
Set the group code for your radio group from 0-142.
Everyone in your group must select the same
group code in order to communicate with each
other.
GMR2889-2CK RADIO
• DC Adapter - #DC-1002
CHARGING THE RADIO
Sending a Direct Call
Adjusting the Sound (Key Beeps)
To select the VOX level:
Key Lock
Direct Call lets you call everyone in your group at
once, or call a single person in your group without
anyone else in the group knowing. It is like a
"speed dial" directly to the person(s) you want to
talk to.
Your radio sounds a beep each time you press a
key (except for PTT and Power boost).
To turn this sound off, press and hold d-call while
turning on the radio. Repeat this step to turn the
sound on.
• Do a "roll call" on the new channel after the
move to be sure no one was left behind. If you
missed someone, return to the previous channel
and issue the signal again.
If you use the rechargeable NiMH battery pack, two
radios can be charged directly or by using the
supplied charging cradle.
1) Enter the menu. VOX appears and the current
setting flashes. The current level (OFF, 1-5)
flashes. Level oF (OFF) disables VOX, while
levels 1-5 set the sensitivity of the VOX circuit.
2) Press either L or M to set the desired VOX
sensitivity level. Use level 1 for increased
sensitivity to voice in normally quiet
1) Press and hold menu/grp for 2 seconds. The
radio displays on GRUP.
2) Tap menu/grp. The radio displays Gnnn (n is a
number). Press L or M to select the group
number.
3) Press PTT or Power boost to return to normal
operation, or press menu/grp to continue to the
next section.
To lock the keypad:
2) When you finish speaking, release PTT or
Power boost. You can now receive incoming
calls. While receiving, rx appears on the display.
1) Enter the menu. Advance through the menu until
LOCK appears. The radio displays oF LOCK.
2) To switch Key Lock from oF (OFF) to on (ON),
press L.
3) To confirm the setting, press menu/grp. The
radio returns to the current mode.
GMRS LICENSE
Charge by Using the Radio
The radio operates on the General Mobile Radio
Service (GMRS) frequencies when using
1) Connect the DC adapter’s plug to the radios DC
IN 9V jack and plug other end into your vehicle’s
accessory power outlet.
2) Charge the battery pack for 16 hours until the
battery indicator stops flashing.
To call everyone in your group, press d-call in
group mode. The radio flashes ALL. Then, press
d-call again. Everyone in your group receives a call
"chirp" for about 3 seconds. When the chirp ends,
begin your conversation.
Choosing a Channel
Note: When you press Power boost, BOOS
appear on the display. The radio transmits at
maximum power when a GMRS channel is
selected. If Power boost is continuously pressed,
1 minute after you start pressing Power boost the
transmission stops and you hear a boost timeout
error tone.
Your radio has 22 channels and 142 Privacy codes
you can use to talk to others. In order to speak to
someone, both your radios must be set to the same
channel and Privacy code.
USING THE RADIO IN STANDARD MODE
environments, and use a higher level to reduce
undesired activation in very noisy environments.
Channels 1-7 and channels 15-22.You must have
a GMRS license issued by the Federal
Use the radio in standard (not group) mode when
you need to be able to communicate with radios
that do not have the group feature.
Note: If you exit the setting mode before confirming
your selection by pressing menu/grp, Key Lock is
set to oF (OFF).
Setting the Ring Tone
Communications Commission to legally use
these channels. For licensing information and
application forms, visit the FCC online at:
800-418-3676. If you have any questions, you can
contact the FCC direct at 1-888-225-5322. No
license is required for operation on channels 8-
14 or operation on any channel in Canada.
Transmitting a Call Tone
This setting selects the tone you hear when
someone places a direct call to you.
Using the Charging Cradle
To choose a channel:
Your radio is equipped with 10 selectable call tones
that are transmitted when you press d-call in
standard mode.
Note: When you make a direct call to "all," your
radio also sends out your nickname or ID so that it
will show up in the call list for everyone in your
group.
1) Connect the adapter's plug to DC IN 9V jack of
the charging cradle and plug the other end into
an AC outlet.
2) Set the charging cradle on the desk or tabletop,
and place the radio in the charging cradle with
the keypad facing forward.
3) Make sure that the LED illuminates. Charge the
battery pack for 16 hours and remove the radio
from the charging cradle after charging.
Press ch tone/scn, then press L or M to increase
or decrease the channel number displayed.
To unlock the keypad:
Choosing a Privacy Code
1) Press and hold menu/grp for 2 seconds, then
tap menu/grp two times until the radio displays
n RING.
2) Press L or M to select the desired ring sound.
With each press, you hear a sample of the
selected tone.
3) Press PTT or Power boost to return to normal
operation, or press menu/grp to continue to the
next section.
Monitor Mode Feature
1) Turn off the radio by rotating vol/off
counterclockwise until it clicks.
2) Turn on the radio again by rotating vol/off
clockwise until it clicks. The keypad is unlocked.
You can select a Privacy Code from 1-142 for each
channel. oFF (OFF) indicates no Privacy code
selected and your radio can receive a signal
regardless of the code settings of the transmitting
radio.
To select a call tone:
Your radio lets you listen for weak signals on the
current channel at the press of a key.
Note: Channels 1-7 and 15-22 have a typical range
of up to 28 miles by pressing the Power Boost
button. HI is displayed when you select a GMRS
channel, and LO is displayed when you select a
FRS channels.
1) Enter the menu. Advance through the menu until
CALL appears. The current call tone number
(1-10) flashes.
2) Press L or M to increase or decrease the
number to the desired call tone. Each tone will
be heard through the speaker.
To call one person in your group, without having
other people know, press d-call in group mode.
Then, use L or M to select the person you want to
call and press d-call again. Your radio sounds
tones for 3 seconds as it sends the call. When the
selected person answers, you can begin your
conversation. You can silence the call tones at any
time by pressing PTT or Power boost.
To turn on the Monitor Mode:
Automatic Power Save Feature
• For brief listening, press mon. MON appears
and rx flashes.
1) Press ch tone/scn twice. The Privacy code
indicator flashes.
2) Press L or M to increase or decrease the
code. You can also select oFF.
3) Press ch tone/scn again.
Your radio has a unique circuit designed to
dramatically extend the life of the batteries. If there
is no transmission nor an incoming call within 3
seconds, your radio switches to the Power Save
mode. The radio is still able to receive transmissions
in this mode.
1 Antenna
13 Microphone
14 DC IN 9V
Warning! The range of channels 1-7 and 15-22 can
be boosted only when you use NiMH batteries.
When you press Power boost while using alkaline
batteries, the range is not boosted.
2 PTT (Push-To-Talk) Button
3 Power Boost Button
4 Weather/Alert Key
5 D-call Key
6 Menu/Group Key
7 Speaker
8 Volume Setting Nob
9 Up/Down Button
10 Headset Jack
INSTALL THE BATTERY
• Press and hold mon for 2 seconds until two
beeps sound for continuous listening. The
receiver circuit stays open, so you hear both the
noise and weak signals.
Note:
15 Channel Indicator
16 Sub Code Indicator
17 Alert Indicator
18 Receive Indicator
19 Miss Indicator
20 Battery Level Indicator
21 VOX Indicator
To transmit the selected call tone, press d-call. The
selected tone is transmitted for a fixed length of
time. Call Tone is cancelled if you press PTT or
Power boost.
Setting the Unit Number
•
For charging batteries directly without the cradle,
use only the #DC-1002 Cigarette Lighter Adapter
code, available from WWW.Uniden.com.
Your radio uses a supplied NiMH battery pack or 4
AAA alkaline batteries (not included).
Each radio in your group needs to be set to a
unique unit number, from 1-16.
Your conversation remains private between you and
the person you called until 15 seconds after your
last conversation. Then, your radio automatically
exits private mode.
Note: Only tones 1-38 are standard across radio
brands. Other settings might differ from brand to
brand. See the specifications for the specific tones
used for each setting.
Other power cords could damage your radio.
To install the NiMH battery pack:
LCD Backlight
1) Press and hold menu/grp for 2 seconds, then
tap menu/grp three times until the radio
•
•
Use only the supplied battery and AC adapter or
approved DC adapter from Uniden.
To turn off Monitor Mode:
The LCD Backlight automatically turns on when any
key (except the PTT and Power boost button) is
pressed. The LCD remains lit for 10 seconds before
turning off.
1) Make sure the radio is off.
22 Call Indicator
23 Charging Contacts
Press mon to return to the previous mode. MON
and rx disappear.
2) Remove the battery compartment door by
pressing the tab at the bottom of the
compartment door, and remove the cover.
displays n
(or your current nickname).
- - - -
2) Press L or M to select the desired unit number.
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Channel Tone/Scan Key
12 Monitor Key
Charge time may vary depending on the battery
life remaining.
3) Press menu/grp to continue to the next section.
Roger Beep
SPECIFICATIONS
REGULATORY INFORMATION
RF EXPOSURE INFORMATION
ONE YEAR LIMITED WARRANTY
Roger beep is a beep that is sent to notify the end of
transmission (both PTT and VOX transmission). You
can hear the roger beep can be heard through the
speaker when both roger beep and key beep are on.
When roger beep is on and key beep is off, you do not
hear the roger beep, but it is transmitted to your party.
Channels
15 GMRS/7 FRS/7 Weather
16
17
18
19
114.8
118.8
123.0
127.3
36
37
38
233.6
241.8
250.3
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
WARNING! Read this information before using
the radio. In August 1996 the Federal
Important: Evidence of original purchase is
required for warranty service.
is void outside the United States of America and
Canada.
Sub Codes
38 Sub-Audible Tones
104 DCS Codes
Communications Commission (FCC) of the United
States with its action in Report and Order FCC
96-326 adopted an updated safety standard for
human exposure to radio frequency
WARRANTOR: UNIDEN AMERICA
PROCEDURE FOR OBTAINING PERFORMANCE
OF WARRANTY: If, after following the instructions
in the owner’s manual you are certain that the
Product is defective, pack the Product carefully
(preferably in its original packaging). Disconnect the
battery from the Product and separately secure the
battery in its own separate packaging within the
shipping carton. The Product should include all
parts and accessories originally packaged with the
Product. Include evidence of original purchase and
a note describing the defect that has caused you to
return it.The Product should be shipped freight
prepaid, by traceable means, to warrantor at:
Operating Frequency
GMRS/FRS:
WX:
(1) This device may not cause harmful interference.
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
CORPORATION ("Uniden")
462.5500 - 467.7125 MHz
162.4000 - 162.5500 MHz
NiMH Battery Pack (BT-1013)
or 4 AAA Alkaline Batteries
1-7 up to 18 miles
ELEMENTS OF WARRANTY: Uniden warrants, for
one year, to the original retail owner, this Uniden
Product to be free from defects in materials and
craftsmanship with only the limitations or exclusions
set out below.
To turn the roger beep OFF, press and hold L while
turning ON the radio. Repeat this step to turn the beep
ON.
Power Source
electromagnetic energy emitted by FCC regulated
transmitters.
DCS Code List
Important: Changes or modifications to this unit
not expressly approved by Uniden could void your
authority to operate this unit. Your radio is set up
to transmit a regulated signal on an assigned
frequency. It is against the law to alter or adjust the
settings inside the radio to exceed those limitations.
Any adjustments to your radio must be made by
qualified technicians.
Range Channel
Those guidelines are consistent with the safety
standard previously set by both U.S. and
international standards bodies. The design of the
radio complies with the FCC guidelines and these
international standards.
Tone Octal
No. Code
Tone Octal
No. Code
Tone Octal
No. Code
109 631
110 632
111 654
112 662
113 664
114 703
115 712
116 723
117 731
118 732
119 734
120 743
121 754
122 036
123 053
124 122
125 145
126 212
127 225
128 246
129 252
130 255
131 266
132 274
133 325
134 332
135 356
136 446
137 452
138 454
139 455
140 462
141 523
142 526
(28 miles with Power boost
button)
WARRANTY DURATION: This warranty to the
original user shall terminate and be of no further
effect 12 months after the date of original retail
sale. The warranty is invalid if the Product is:
(A) damaged or not maintained as reasonable or
necessary, (B) modified, altered, or used as part
of any conversion kits, sub-assemblies, or any
configurations not sold by Uniden, (C) improperly
installed, (D) serviced or repaired by someone
other than an authorized Uniden service center for
a defect or malfunction covered by this warranty,
(E) used in any conjunction with equipment or parts
or as part of any system not manufactured by
Uniden, or (F) installed or programmed by anyone
other than as detailed by the owner’s manual for
this product.
USING THE WEATHER RADIO
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
023
025
026
031
032
043
047
051
054
065
071
072
073
074
114
115
116
125
131
132
134
143
152
155
156
162
165
172
174
205
223
226
243
244
245
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
251
261
263
265
271
306
311
315
331
343
346
351
364
365
371
411
412
413
423
431
432
445
464
465
466
503
Channel 8-14 up to 5 miles
Channel 15-22 up to 18 miles
(28 miles with Power boost
button)
Your radio can receive weather broadcasts from the
NOAA National Weather Service. When in the
Weather Radio Alert mode, the system functions as it
does in standard mode but also monitors the selected
weather channel for alerts when not communicating.
While using the Weather Radio, you are not able to
receive GMRS communications.
Never allow children to operate the radio without
adult supervision and the knowledge of the
following guidelines.
Battery Life
15 Hours typ. - NiMH
Battery Pack (5/5/90 duty
cucle)
To be safe and sure:
• Never open your radio’s case.
WARNING! It is up to the user to properly operate
this radio transmitter to insure safe operation.
Please adhere to the following:
• Never change or replace anything in your radio
except the batteries.
Uniden America Service
4700 Amon Carter Blvd. Fort Worth, TX 76155
(800) 297-1023 during regular business hours
(CST)
1) To turn on the Weather Radio Broadcast mode,
press wx/alert. WX appears.
2) Press ch tone/scn, then press L or M to increase
or decrease the number to the desired Weather
Channel.
Your radio might cause TV or radio interference
even when it is operating properly. To determine
whether your radio is causing the interference, turn
it off. If the interference goes away, your radio is
causing it. Try to eliminate the interference by
moving your radio away from the receiver. If you
cannot eliminate the interference, the FCC requires
that you stop using the radio.
Use only the supplied or an approved antenna.
Unauthorized antennas, modifications, or
attachments could impair call quality, damage the
radio, or result in violation of FCC regulations.
Do not use the radio with a damaged antenna.
If a damaged antenna comes into contact with the
skin, a minor burn may result. Please contact your
local dealer for a replacement antenna.
Body-worn Operation
Frequency Chart
Ch. Freq. [MHz] Cross Ref.
Ch. Freq. [MHz] Cross Ref.
operation.)
1
2
3
4
5
6
7
8
9
462.5625
462.5875
462.6125
462.6375
462.6625
462.6875
462.7125
467.5625
467.5875
FRS & GMRS 1
FRS & GMRS 2
FRS & GMRS 3
FRS & GMRS 4
FRS & GMRS 5
FRS & GMRS 6
FRS & GMRS 7
FRS 8
12 467.6625
13 467.6875
14 467.7125
15 462.5500
16 462.5750
17 462.6000
18 462.6250
19 462.6500
20 462.6750
21 462.7000
22 462.7250
FRS 12
FRS 13
3) To exit the Weather Radio Broadcast mode, press
wx/alert. WX disappears.
FRS 14
STATEMENT OF REMEDY: In the event that the
product does not conform to this warranty at any
time while this warranty is in effect, warrantor will
either, at its option, repair or replace the defective
unit and return it to you without charge for parts,
service, or any other cost (except shipping and
handling) incurred by warrantor or its
GMRS 11
GMRS 8
GMRS 12
GMRS 9
GMRS 13
GMRS 10
GMRS 14
GMRS 15
• To change the channel continuously, press and
hold L or M for more than 1 second.
• When in the Weather Radio Broadcast mode, you
can only set the Key Lock from the Menu mode.
Hazardous Environments: Do not operate the
radio in hazardous environments. Explosion or fire
may result. Do not operate the radio near
unshielded electrical blasting caps.
Covered under one or more of the following
U.S. patents:
This device was tested for typical body-worn
operations using the supplied belt-clip.
To maintain compliance with FCC RF exposure
requirements, Body-worn operations are restricted
to the supplied belt-clip.
5,203,015 5,214,789 5,491,745 5,497,508
5,517,677 5,557,606 5,574,994 5,610,946
5,613,201 5,625,870 5,627,876 5,628,059
5,634,196 5,634,205 5,678,176 5,697,096
5,717,312 5,722,070 5,787,345 5,901,341
6,021,326 6,084,861 6,163,691 6,195,415
6,353,730 6,618,015 6,839,550 6,980,770
7,102,568 7,138,945 7,200,358 7,251,453
FRS 9
Choosing an Emergency/Weather Channel
Under certain conditions, radios can interfere with
blasting operations and may cause an explosion.
Turn your radio OFF to prevent accidental
transmission when in a blasting area or in areas
posted: "Turn off two-way radio." Construction
crews often use remote control RF devices to set
off explosives.
10 467.6125
11 467.6375
FRS 10
There are 7 NOAA channel frequencies available and
these frequencies are common between the US and
Canada.You need to know what frequency is being
transmitted in your location.
representatives in connection with the performance
of this warranty. Warrantor, at its option, may
replace the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE
IS THE SOLE AND ENTIRE WARRANTY
PERTAINING TO THE PRODUCT AND IS IN LIEU
OF AND EXCLUDES ALL OTHER WARRANTIES
OF ANY NATURE WHATSOEVER, WHETHER
EXPRESS, IMPLIED OR ARISING BY
FRS 11
For hand-held operation, the radio should be held
1 inch from the user's face. The use of accessories
that do not satisfy these requirements may not
comply with FCC RF exposure requirements and
should be avoided.
CTCSS Chart (Hz)
Code Freq.
1) Press and hold wx/alert. appears.
2) When the unit receives a warning signal, it beeps
for 5 seconds.
blink.
3) To turn off Weather Alert, press and hold wx/alert.
Code Freq.
oFF
1
OFF
67.0
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
131.8
and channel indicator
Care and Safety: To clean the radio, use a soft
cloth dampened with water. Do not use cleaners or
solvents because they can harm the body of the
unit and leak inside, causing permanent damage.
Use a dry, lint-free cloth to clean the battery
contacts. Do not submerge the unit in water. If the
unit gets wet, turn it off and remove the batteries
immediately.
For more information about RF exposure, please
136.5
141.3
146.2
151.4
156.7
162.2
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
100 506
101 516
102 532
103 546
104 565
105 606
106 612
107 624
108 627
2
3
disappears.
OPERATION OF LAW, INCLUDING, BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.THIS WARRANTY DOES
NOT COVER OR PROVIDE FOR THE
4
5
• When Weather Alert is activated, the highest
priority is given to this function. It checks the
weather alert signals every 7 seconds. When the
unit finds a warning signal, it switches to the
warning receive mode automatically.
6
7
8
Dry the battery compartment with a soft cloth to
minimize potential water damage. Leave the battery
compartment cover off overnight to ensure
complete drying. Do not use the radio until the unit
is completely dry.
REIMBURSEMENT OVERPAYMENT OF
9
• Weather Alert is activated even if key beep is
turned off.
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow this exclusion or limitation
of incidental or consequential damages so the
above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you
specific legal rights, and you may also have other
rights which vary from state to state. This warranty
10
11
12
13
14
15
NOAA Weather Radio Frequency List
Channel 1 162.550 MHz Channel 5 162.450 MHz
Channel 2 162.400 MHz Channel 6 162.500 MHz
Channel 3 162.475 MHz Channel 7 162.525 MHz
Channel 4 162.425 MHz
© 2008 Uniden America Corporation
All rights reserved Printed in China
UTZZ01038ZZ(0)
Download from Www.Somanuals.com. All Manuals Search And Download.
|