Introduction
Welcome
Congratulations on your purchase of the BCT-10 Highway
Information System & Scanning Radio! State-of-the-art
engineering and advanced electronics provide you with a
preprogrammed information radio designed for easy operation and
dependability.
With the BCT-10 Scanning Radio, you can listen to hundreds of
highway patrol and police frequencies, as well as a number of
weather channels.
Plus, new built-in technology sounds an alarm when a highway
patrol unit using a mobile extender is detected!
Best of all, you don’t have to program any frequencies. Just set the
BCT-10 for your state, and the scanner will do the rest. Please
read this Operating Guide thoroughly before attempting to operate
the unit.
Features
• Highway Patrol Detection
• Windshield Mountable
with Strength Meter
• Local Police Coverage
• Highway Patrol Coverage
• 9 Level Strength Meter
• Instant Weather
• Built-in Speaker
• Pre-Programmed Scanner
covers all 50 States Plus
Canada
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Unpacking
Carefully remove all items from the box. If there is any visible
damage, do not operate the equipment. Notify your dealer or
shipping carrier immediately.
For information or instructions on any problem that you may have,
call the Uniden Customer Service Center at:
(800) 297-1023 Monday through Friday,
8:00 a.m. to 5:00 p.m. Central.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Included with Your BCT-10 Scanner
Y
A
HIGHW
SYSTEM
OFF
MODE
MUTE
M
ALAR
L/0
TE
STA
HOLD
The BCT-10 Highway
Information System
Windshield Mounting
Bracket and Hardware
Visor Clip Mounting
Bracket
Y
A
W
MODE
L/0
HIGHW
SYSTEM
MUTE
E
T
A
ST
M
ALAR
HOLD
OFF
BCT-10 Antenna
Cigarette Adapter Power
Cord
BCT-10 Operating Guide
Flexible Mobile Antenna
Other Printed Material
Straight Power Cord
If any of these items are missing, please contact your place of
purchase.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Installation
Installation
The BCT-10 uses a highly sensitive antenna to receive radio
signals. Its sensitivity and range depend on the method of
installation and the direction of the antenna in relation to the signal
source. Before you decide where to put your scanner, please keep
in mind one important factor:
For safety, do not mount the BCT-10 in a location where it will
obstruct your driving vision.
Helpful Tips
The antenna is located on the side of the unit. It should not be
obstructed and should be pointed as close to straight up or down
for best operation.
• Do not mount the unit in front of the heater or defroster vents.
• Do not leave the unit in direct sunlight or in the glove
compartment of a closed car for long periods of time, as
extreme changes in temperature may cause internal damage.
Also, removing the unit from the windshield makes you less
susceptible to break-in and theft.
• Be sure the BCT-10 is mounted free of obstructions from the
rear view mirror, sun visors, or the ceiling of the automobile.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Installation
Installing the Antenna
BCT-10 Antenna
1. Pinch the sides of the
antenna and attach it to
the BCT-10.
HIGHWAY
SYSTEM
MODE
ALARM
MUTE
STATE
Flexible Mobile Antenna
1. Mount the antenna on the
inside of the windshield at
the far right-hand
(passenger) side.
Caution: Be sure the antenna does not obstruct the driver’s vision
in any way.
2. Route the antenna cable down the edge of the windshield and
around the dash.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Installation
Caution: Be sure the cable is out of the way of anyone getting in or
out of the car.
3. Plug the cable’s BNC
connector into the BCT-10.
HIGHWAY
SYSTEM
MODE
ALARM
MUTE
STATE
Mounting the BCT-10
Visor Mounting
1. Snap the visor clip onto the
BCT-10.
SQUELCH
Slots
Note: Make sure that the bracket tabs fit securely in the slots.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Installation
2. Slide the clip over the front
of the visor.
SQUELCH
3. Adjust the angle of the
antenna as close to
straight up or down as
possible.
SQUELCH
Note: You can remove and replace the BCT-10 by sliding both
the unit and the visor mount off and on the visor.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Installation
Windshield Mounting
to the Helpful Tips on page 5 for some guidelines on mounting
positions.
2. Put the metal
mounting
1. Windshield
2. Road Surface
3. Metal Mounting
Bracket
4. Metal Mounting
Bracket
1
bracket on
the
windshield to
adjust it for
best position.
2
parallel to road
4
3
3. If necessary, adjust the metal
mounting bracket so that
when you slide the BCT-10
onto it, it is parallel to the
road surface and fits flush
against the windshield. Your
BCT-10 should look like the
example at the right once it
is installed.
VOLUME
OFF
VOLUME
OFF
VOLUME
OFF
Caution: Do Not adjust the metal mounting bracket with the
BCT-10 attached. Doing so can cause damage to the
bracket and the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Installation
4. Snap the windshield
mounting clip onto the
BCT-10.
VOLUME
OFF
Slots
5. Slide the plastic windshield
mounting clip into the the
metal mounting bracket.
HIGHWAY
SYSTEM
MODE
L/0
ALARM
HOLD
MUTE
STATE
The mounting clip locks into the plastic portion at three different
positions. These positions can be used for vehicles with different
vertical angles of their windshields. The back position can be used
for vehicles with windshields that are slanted back.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Installation
6. Place the bracket and the
BCT-10 in the proper location
on the windshield of your
vehicle and press the suction
cups firmly against the
VOLUME
OFF
windshield. If the BCT-10
does not fit flush against the
windshield, try a different
position on the metal
VOLUME
OFF
mounting bracket.
VOLUME
OFF
7. Adjust the angle of the
antenna as close to straight
up or down as possible.
SQUELCH
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Connecting the Power
Direct Connection
WARNING: The BCT-10 is designed to operate only with 12V DC,
negative ground power systems. Operation of the unit
on other voltages or polarities will cause damage to
the unit and may create a fire hazard.
The straight power cord provided with the unit has bare wires at
one end, and a small connector at the other end.
1. Connect the positive wire to a 12V DC source in your vehicle’s
fuse box.
2. Connect the other wire to ground.
Y
A
HIGHW
SYSTEM
OFF
MODE
MUTE
ALARM
L/0
E
T
A
ST
HOLD
Fuse
Box
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Connecting the Power
3. Run the power cord from the fuse box to the BCT-10.
Note: Ensure the cord does not interfere with vehicle operation
or cause a tripping hazard.
4. Plug the power cord connector into the Control Unit at the jack
labeled “DC 12V.”
Note: Push the connector firmly into the jack.
Using the Cigarette Lighter Adapter
1. Insert the small connector
into the jack on the side of
the unit.
Y
HIGHWA
SYSTEM
OFF
MODE
MUTE
ALARM
L/0
E
T
A
ST
HOLD
2. Insert the other end into the
cigarette lighter socket of
your vehicle.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Connecting the Power
When installing the power cord, make sure that:
• The socket is clean to allow proper contact.
• The power cord does not block the antenna area of the unit.
Your unit also comes with 10 power cord mounting clips. You can
use these clips to attach the power cord to the window frame or
other parts of the vehicle, keeping it neat and out of the way. Use
the double-sided foam tape squares to attach each clip. Slip the
power cord into the clip to hold it securely in place.
Replacing the Fuse
The cigarette lighter plug contains a 1-ampere fuse to protect it
from power surges.
1. To replace the fuse, unscrew the top of the plug.
2. Remove the fuse and replace it with the same type.
3. To replace the top, push in
the two metal contacts and
twist into place.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Operating Instructions
Applying Power
1. Turn the OFF/VOLUME
control counter clockwise to
power on the scanner. Adjust
the volume about 1/4 turn.
2. During power-on, a self-test
is performed. Check the front
control panel for proper
operation.
MUTE
SR HP
WX LP
DISPLAY
MUTE
HOLD
3. All the LED’s on the front
control panel light up and the
numbers 1 through 9 count
up on the LED display. An
Alert tone is also sounded.
This tells you that the
9
scanner is working properly.
MUTE
HOLD
4. The currently selected state
appears on the display. The
BCT-10 always comes on
with the last settings
TX
selected, and in the last
mode of operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Operating Instructions
Adjusting the Squelch
Think of the Squelch Control as a gate.
1. Turn the SQUELCH control fully counterclockwise. This raises
the “Squelch Gate” so high that no signals can get through.
Strong Signals
Medium Signals
Weak Signals
Noise
2. Turn the SQUELCH control fully clockwise until you hear a
hiss. This lowers the “Squelch Gate” so that everything gets
through ... noise, weak signals, and strong signals.
Strong Signals
Medium Signals
Weak Signals
Noise
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Operating Instructions
3. Turn the SQUELCH conrol back counter clockwise just until
the hiss stops. Now the “Squelch Gate” allows only strong
signals through.
Strong Signals
Medium Signals
Weak Signals
Noise
4. Sometimes when you open the Squelch, you may trigger the
Alert feature even though no highway patrol cars are in the
area. If this happens, turn the SQUELCH control
counterclockwise until the “rushing” noise stops. Then turn the
BCT-10 off, and back on, to reset the Alert feature.
Note: In metropolitan areas, you may want to adjust the Squelch
control more counterclockwise to reduce the range of
the Alert feature. When set fully counterclockwise,
Squelch limits the Alert range to a short distance.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Operating Instructions
Selecting the State
SYSTEM
1. Select the state you are
operating in by pressing
MODE
ALARM
MUTE
STATE
the
you press and hold the
key for 2 seconds, the
S
key repeatedly. If
S
selector moves rapidly
through all the states and
Canadian provinces.
MUTE
HOLD
2. The state code appears on
the display. See the
TX
following page for a list of
State codes.
Note: The state codes are in alphabetical order by abbreviation.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Operating Instructions
State Codes
Code
State
Code
NM
State
New Mexico
Nevada
AK
AL
AR
AZ
CA
CO
CT
DC
DE
FL
Alaska
Alabama
NV
NY
OH
OK
OR
PA
RI
Arkansas
Arizona
New York
Ohio
California
Colorado
Connecticut
District of Columbia
Delaware
Florida
Oklahoma
Oregon
Pennsylvania
Rhode Island
South Carolina
South Dakota
Tennessee
Texas
SC
SD
TN
TX
UT
VA
VT
WA
WI
GA
HI
Georgia
Hawaii
IA
Iowa
Utah
ID
Idaho
Virginia
IL
Illinois
Vermont
IN
Indiana
Washington
Wisconsin
KS
KY
LA
MA
MD
ME
MI
Kansas
Kentucky
Louisiana
Massachusetts
Maryland
Maine
WV
WY
AB
BC
MB
NB
NF
NS
NT
ON
PE
PQ
SK
YT
XX
West Virginia
Wyoming
Alberta
British Columbia
Manitoba
Michigan
Minnesota
Missouri
New Brunswick
Newfoundland
Nova Scotia
Northwest Territories
Ontario
MN
MO
MS
MT
NC
ND
NE
NH
NJ
Mississippi
Montana
North Carolina
North Dakota
Nebraska
New Hampshire
New Jersey
Prince Edward Island
Quebec
Saskatchewan
Yukon Territories
All Frequencies
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Operating Instructions
Selecting the Frequencies to Scan
Scanning All Frequencies
Note: The Alert feature is not active in this mode.
MUTE
1. To scan all frequencies
HOLD
(except Weather), press
XX
the
S
key repeatedly or
press and hold the
S
key until “XX” is blinking on
the LED display.
2. All frequencies, except weather channels, are scanned for an
active transmission.
MUTE
3. When the BCT-10 finds an
HOLD
active frequency it
XX
activates a buit-in two
second delay before it
resumes scanning.
Note: The
M
key does not operate in XX mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Operating Instructions
Scanning Highway Patrol Frequencies
HIGHWAY
SYSTEM
1. To scan highway patrol
frequencies exclusively,
MODE
MUTE
ALARM
press the
M
key repeatedly
until HP is blinking in the
LED display.
STATE
MUTE
HOLD
HP
HP
MUTE
HOLD
2. The HP LED lights up.
3. While scanning, the BCT-10
displays the state code for
the state you selected. When
the BCT-10 detects an active
frequency, it displays HP in
the LED. and stops for two
seconds before it resumes
scanning.
MUTE
HOLD
TX
MUTE
HOLD
HP
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Operating Instructions
Scanning All Police Frequencies
HIGHWAY
SYSTEM
1. To scan highway patrol and
local police frequencies,
MODE
ALARM
press the
repeatedly until LP is
M
key
MUTE
STATE
blinking on the LED display.
MUTE
HOLD
LP
LP
MUTE
HOLD
2. The LP and HP LED’s will
light up.
3. While scanning, the
BCT-10 displays the state
code for the state you
selected. When the BCT-10
detects an active
MUTE
HOLD
TX
LP
HP
MUTE
HOLD
frequency, it displays LP
when monitoring an active
local police frequency and
HP when monitoring an
active highway patrol
MUTE
HOLD
frequency. The BCT-10 will
stop for two seconds, and
then resume scanning with
the state code displayed
on the LED.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Operating Instructions
Highway Patrol Alarm
In most cases, when you are
within three miles of a
MUTE
HOLD
04
HP
highway patrol unit, and a
mobile extender is in use,
your BCT-10 will set off a
visual and audible alarm. The
signal strength will be
MUTE
HOLD
displayed, and the LED will
return to the HP display. The
time the ALARM LED will
stay on depends on the
signal strength.
Duration
Strength
1 - 2
3 - 5
6 - 8
9
3 Minutes
2 Minutes
1 Minute
30 Seconds
Setting the Highway Patrol Alarm Range
A range setting is always active for the highway patrol alert. You
can set the range for either standard or long range. Signal strength
is measured from 1- 9. In standard mode, only signals above a
level 5 strength will trigger an audible alert tone. In long range
mode, all signal strengths from 1- 9 will trigger an alert tone. To
select the range:
HIGHWAY
1.
SYSTEM
Press and Hold the
for 2 seconds.
M
key
MODE
ALARM
MUTE
STATE
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Operating Instructions
MUTE
HOLD
2. The LR and SR LED’s
toggle and you hear two
short beeps once either
standard or long range
mode is selected.
HP
Setting the Highway Patrol Alarm Volume
You can set the Alert Tone volume to either Low, Medium, or High.
To change the Alert Tone volume:
HIGHWAY
1.
Press the
A
Key.
SYSTEM
ALARM
MODE
MUTE
STATE
2. You hear a beep and the
LED will display L (low), M
(medium), or H (high).
MUTE
HOLD
L
MUTE
HOLD
M
H
MUTE
HOLD
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Operating Instructions
Muting the Highway Patrol Alarm
While in the highway patrol mode you can turn off the alarm tone
during the time you are listening to a frequency or disable the
alarm tone permanently. To disable the alarm tone while listening
to a frequency:
HIGHWAY
1. While in the highway patrol
SYSTEM
mode and after you receive
MODE
ALARM
an alarm tone, press the
key.
m
MUTE
STATE
MUTE
HOLD
2. The MUTE LED flashes.
HP
Note: Only the alarm tone will be disabled. You will still receive
highway patrol alarms but only the ALARM LED will
come on.
3.
To enable the Alert Tone again, press the
m
key again.
Note: When the ALARM LED goes off, the mute mode will no
longer be on.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Operating Instructions
To disable the alarm tone permanently:
1.
HIGHWAY
SYSTEM
Press and Hold the
for two seconds.
m
key
MODE
ALARM
MUTE
STATE
MUTE
HOLD
2. You hear a two beeps and
the MUTE LED comes on.
HP
Note: When the MUTE LED is on and not flashing, you can
receive highway patrol alarms, but the alarm tone does
not sound.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Operating Instructions
Monitoring Weather Frequencies
HIGHWAY
SYSTEM
1. To monitor weather
frequencies, press the
repeatedly until WX is
M
key
MODE
MUTE
ALARM
blinking on the LED display.
STATE
MUTE
HOLD
WX
2. While scanning, the BCT-10
will display WX. When the
BCT-10 detects an active
frequency, it displays the
weather channel in the LED
and stops scanning.
MUTE
HOLD
WX
W2
MUTE
HOLD
SYSTEM
3.
Press the
L
key to make
the BCT-10 scan for the next
weather frequency.
MODE
ALARM
MUTE
STATE
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Operating Instructions
Deleting Frequencies
Some frequencies that have been preprogrammed into your
BCT-10 may not be of immediate interest to you, or a frequency
may be experiencing interference. You can lock out that frequency
from scanning.
SYSTEM
1. When the scanner stops
on the undesired
MODE
ALARM
MUTE
STATE
frequency, press
time.
L
one
2. To lock out additional frequencies, repeat Step 1.
Note: You can delete a maximum of 50 frequencies. Although it
is possible to delete the highway patrol alarm
frequencies, this should never be done unless
absolutely necessary for proper operation of your
BCT-10. This causes the highway patrol alarm feature
to be inactive on that frequency. No further alarms will
be received until the deleted frequencies are restored or
a new state is selected.
Caution: When you lock out more than 50 frequencies, the first
locked out frequency is deleted. You cannot lock out all
of the alarm, local police, and highway patrol
frequencies. If you lock out all of the frequencies by
accident, the BCT-10 will sound two short beeps.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Operating Instructions
Restoring Deleted Frequencies
Please note that you can only restore all deleted frequencies at the
same time.
To restore the deleted frequencies:
1. Make sure the BCT-10 is not
scanning. To stop the unit
from scanning, turn the
SQUELCH knob toward the
front of the BCT-10.
SYSTEM
2.
Press and hold the
L
key
until you hear two beeps.
MODE
ALARM
MUTE
STATE
3. All deleted frequencies are now restored.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Operating Instructions
Using HOLD to Stay on a Selected Frequency
When scanning stops on a desired frequency, you can lock onto
that frequency for as long as you like.
To monitor only one frequency:
SYSTEM
1. When the scanner stops
on the desired frequency,
MODE
ALARM
MUTE
STATE
press the
H
key.
2. The LED display now
indicates the service,
MUTE
HOLD
LP
either highway patrol or
local police, you are
monitoring. The scanner
remains on that frequency
until you cancel the Hold
MUTE
HOLD
HP
mode by pressing
H
Note: While in the Hold mode, the Alarm feature is inactive!
3. To resume scanning and reactivate the Alert feature, press the
H
key.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Operating Instructions
If the BCT-10 stops on an undesired frequency, press the
H
key
twice to force the unit to start scanning again before the end of that
transmission.
BE CAREFUL!!When you are in the Hold mode, there will be no
Alert tones or Warning light, even if you are on
the Alert frequency.
REMEMBER!! When you apply power, the BCT-10 comes on to
exactly the same service and in exactly the
same mode as when last turned off. If you are
monitoring an Alert frequency in the Hold mode
when you turn the BCT-10 off, it will come back
to that Alert frequency in Hold mode when you
turn it back on. The Alert feature will be
inactive. To restore the Alert feature, press the
H
key.
Memory Backup
Your BCT-10 has a memory backup system that remembers your
frequency selections and deletions when you turn off the unit. This
memory lasts permanently without any external power to the unit.
Birdies
All radios are subject to receiving undesirable signals. If your
scanner stops during Scan mode and no sound is heard, press the
H
key twice to resume scanning.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Troubleshooting
If your BCT-10 is not performing properly, try the steps listed
below.
POSSIBLE SOLUTION
PROBLEM
Check power cord and
in-line fuse.
Scanner is not working properly.
Check the Volume and
Squelch settings.
Check antenna and
antenna connection, or
change antenna.
Signal is weak or distorted.
Improper reception.
Check antenna and
antenna connection, or
change antenna.
Reposition scanner.
Scan won’t stop.
Check Squelch adjustment.
Check antenna and
antenna connection, or
change antenna.
Incomplete reception.
Fringe area of reception.
Check Squelch adjustment.
Weather Search (WX) won’t work. Check Squelch adjustment.
No active station within
range.
If you still cannot get satisfactory results and you wish to receive
product information or return the unit for service, please call or
write the Uniden Parts and Service Division at:
Uniden America Corporation
4700 Amon Carter Blvd.
Fort Worth, TX 76155
(800) 297-1023 Monday through Friday,
8:00 a.m. to 5:00 p.m. Central
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Optional Accessories
The following optional accessories for your BCT-10 are available
from your local Uniden Dealer or through the Uniden Customer
Service Center by calling: (800) 297-1023, 8:00 a.m. to 5:00 p.m.
Central, Monday through Friday.
Windshield Mounting
Bracket and Hardware
Visor Clip Mounting
Bracket
BCT-10 Antenna
Straight Power Cord
Flexible Mobile Antenna
Y
A
MODE
EM
T
S
Y
L/0
HIGHW
S
MUTE
E
T
A
ST
ALARM
HOLD
OFF
Cigarette Adapter
Power cord
BCT-10 Operating
Guide
®
External Speaker
Coiled Cigarette Adapter
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Specifications
Size:
76W X 136.5D X 33H
Weight:
180 g
Power:
13.8 VDC
Operating Temperature:
Antenna:
-20° C (-4° F) to +60° C (+140° F)
50Ω impedance
RF Sensitivity:
(FM 12dB signal to noise ratio at 3kHz deviation)
37.02 - 46.02 MHz 0.3µV
138.3450 - 172.0200 MHz 0.4µV
423.0000 - 508.4875 MHz 0.5µV
Frequency Coverage:
VHF Low Band
37.02 - 46.02 MHz
VHF High Band
138.3450 - 172.0200 MHz
UHF Band
423.0000 - 508.4875 MHz
Audio output:
Max 1W
Certified in accordance with FCC Rules and Regulations Part 15
as of date of manufacture.
Specifications are typical and subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
34
BCT-10
Y
A
HIGHW
SYSTEM
OFF
MODE
MUTE
M
ALAR
L/0
E
T
A
ST
HOLD
HIGHWAY INFORMATION SYSTEM &
PREPROGRAMMED WARNING SCANNER
Operating Guide
UBZZ01258ZZ
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
Before you use this scanner, please observe the following:
WARNING!
Uniden America Corporation does not represent this unit to be
waterproof. To reduce the risk of fire, electrical shock, or
damage to the unit, do not expose this unit to rain or moisture.
IMPORTANT!
The installation, possession, or use of this scanning radio in a
motor vehicle may be prohibited, regulated, or require a permit
in certain states, cities, and/or local jurisdiction. Your local law
enforcement officials should be able to provide you with
information regarding the laws in your community.
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Indicators
H
A. DC Input
B. Speaker Out
C. On/Off Volume
I
D. ALARM Key
A
E. HOLD Key
H
A
F. Control Panel
J
G. STATE Key
S
I
K
B
L
H. Windshield
Bumpers
Y
A
HIGHW
M
SYSTEM
OFF
I. Antenna
MODE
MUTE
ALARM
C
L/0
J. MUTE Key
K. Squelch Control
L. MODE Key
M. L/O (Lock Out)
Key
m
E
T
A
ST
HOLD
D
E
M
F
L
G
1
3
4 5
2
6
MUTE
HOLD
SR HP
LR LP
7 8
1. ALARM LED
2. MUTE LED
5. Highway Patrol LED
6. HOLD LED
3. 2 Digit LED Display
4. Standard Range LED
7. Long Range LED
Download from Www.Somanuals.com. All Ma8nu.als SeaLrchoAcndaDlowPnlooadl.ice LED
Troubleshooting........................................................................... 32
Optional Accessories................................................................... 33
Specifications .............................................................................. 34
Uniden® and Bearcat® are registered trademarks of Uniden
America CorpoDroawtnilooadnfr.om Www.Somanuals.com. All Manuals Search And Download.
One Year Limited Warranty
Important:
Evidence of original purchase is required for warranty
service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail
owner, this Uniden Product to be free from defects in materials and craftsmanship
with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be
of no further effect 12 months after the date of original retail sale. The warranty is
invalid if the Product is (A) damaged or not maintained as reasonable or necessary,
(B) modified, altered, or used as part of any conversion kits, subassemblies, or any
configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired
by someone other than an authorized Uniden service center for a defect or
malfunction covered by this warranty, (E) used in any conjunction with equipment or
parts or as part of any system not manufactured by Uniden, or (F) installed or
programmed by anyone other than as detailed by the Operating Guide for this
product.
STATEMENT OF REMEDY: In the event that the product does not conform to this
warranty at any time while this warranty is in effect, warrantor will repair the defect
and return it to you without charge for parts, service, or any other cost (except
shipping and handling) incurred by warrantor or its representatives in connection with
the performance of this warranty. THE LIMITED WARRANTY SET FORTH ABOVE
IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND
IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION
OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS
WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR
PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do
not allow this exclusion or limitation of incidental or consequential damages so the
above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. This warranty is void outside the
United States of America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after
following the instructions in this Operating Guide you are certain that the Product is
defective, pack the Product carefully (preferably in its original packaging). Include
evidence of original purchase and a note describing the defect that has caused you
to return it. The Product should be shipped freight prepaid by traceable means, or
delivered, to warrantor at:
Uniden America Corporation
Parts and Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
(800) 297-1023, 8:00 am to 5:00 pm Central, Monday through Friday
Download from Www.Somanuals.com. All Manuals Search And Download.
PAT. UNDER ONE OR MORE OF THE FOLLOWING
U.S. PATENT NUMBERS:
3,883,808, 3,961,261, 3,962,644, 3,974,450
3,974,452, 3,987,400, 3,996,521, 3,996,522
4,000,468, 4,027,251, 4,057,760, 4,092,594
4,100,497, 4,114,103, 4,123,715, 4,153,877
4,156,193, 4,157,505, 4,179,662, 4,219,821
4,270,217, 4,398,304, 4,409,688, 4,455,679
4,461,036, 4,521,915, 4,627,100, 4,888,815
4,932,074, 4,947,456, 5,014,348, DES 253,173
DES 272,737, RE 31,523
©1995Uniden AmericaCorporation.Allrightsreserved.
Printedin thePhilippines
Download from Www.Somanuals.com. All Manuals Search And Download.
|
