DXAI 4288-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
22
22
23
24
24
27
28
Welcome/Features
2
3
5
6
Find Handsets
Using Call Waiting
Controls and Functions
Terms Used in this Manual
Accessibility
Using the Speed Dial Memory
Storing Names and Numbers in Speed Dial Memory
Storing Caller ID Messages in Speed Dial Memory
Making Calls from Speed Dial Memory
Installing the Phone
7
7
8
A. Choose the Best Location
B. Install the Rechargeable Battery Packs into the Handsets
C. Connect the Main Base and Charging Cradle,
and Charge the Handsets
Caller ID and CIDCW (Caller ID on Call
Waiting)
29
30
31
32
32
9
10
11
12
Viewing the Caller ID Message List
Deleting Information from the Caller ID List
Making a Call from the Caller ID List
Caller ID on Call Waiting (CIDCW)
D. Mount the Main Base on a Wall
Installing the Beltclip
Headset Installation
Register Handsets to the Main Base
The Integrated Answering Device
33
before Using!
13
14
Setting Up Your Answering System
34
When to Re-register Handsets
Turning the Answering System On/Off
43
Basic Setup
15
15
15
16
17
18
18
19
19
20
20
21
21
22
Using Your Answering System
44
Activating AutoTalk
Remote Operation
49
Activating Caller ID on Call Waiting
Entering Your Area Code
Choosing the Dialing Mode
Setting the Language
Changing the Digital Security Code
52
53
55
Note on Power Sources
General Information
Selecting the Ring Tone and Volume
Troubleshooting
56
Using Your Phone
Making and Receiving Calls
Transferring a Call
Redialing the Last Dialed Number
Adjusting the Earpiece Volume
Tone Dialing Switch-over
Traveling Out-of-Range
Liquid Damage
59
Precautions & Warranty
60
62
63
I.C. Notice
Index
Remote Operation Card
w w w . u n i d e n . c o m
[ 1 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Congratulations on your purchase of the Uniden dual handset cordless telephone and answering
system. This phone is designed and engineered to exacting standards for reliability, long life, and
outstanding performance.
Welcome
Features
Note:Illustrations in this manual are used for explanation purposes. Some
illustrations in this manual may differ from the actual unit. The color of your
cordless phone may vary.
• 2.4GHz Extended Range Technology
• Dual Handset System
(Extra Handset & Charger Included)
• Call Transfer from Handset to Handset
• Integrated Answering Device
• Caller ID/Caller ID on Call Waiting
• 3-Line Backlit LCD
• 10 Number Memory Dialing
• Last Number Redial
• Tone/Pulse Dialing
• Page/Find Handset Key
• Earpiece/Ringer Volume Controls
• Mute or Turn Ringer Off
• Hearing Aid Compatible
• 20 Channel Auto Scan
• Desk or Wall Mountable
• Trilingual Menu Displays/Voice Prompts
• 30 Caller ID Memory
If you have any trouble with your phone, call our Customer Hotline at 1- 800-297-1023,
Mon-Fri 7 am to 7 pm, Sat/Sun 9 am to 5 pm, CST. (Phone support is closed on holidays.)
For more information on Uniden products and accessories, be sure to visit our web site:
Uniden® is a registered trademark of Uniden America Corporation.
AutoTalk, AutoStandby, UltraClear Plus, Random Code, and AutoSecure are trademarks of
Uniden America Corporation.
w w w . u n i d e n . c o m
[ 2 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Functions
1. Handset antenna
2. Jack for optional headset
3. Beltclip hole
Handsets
1
4. Ringer speaker
5. Handset battery compartment
6. Handset earpiece
7. LCD display
2
3
6
8.
/
/vol/ (earpiece volume, ringer
volume and scroll) key (pages 15, 18 and 21)
9. Call id/menu key (pages 15 and 29)
10. /tone/ key (left cursor)
(pages 21 and 24)
7
8
9
*
4
13
14
15
11. Redial/pause key (pages 20 and 26)
12. Select/channel key (pages 15, 22 and 24)
13. Talk/flash key (pages 19 and 23)
14. End key (pages 19 and 21)
15. Memory key (page 24)
5
16
17
16. #/
(right cursor) key (page 24)
10
11
17. Delete/transfer key (pages 20 and 31)
18. Handset microphone
19. Handset charging contacts
18
12
19
w w w . u n i d e n . c o m
[ 3 ] C O N T R O L S & F U N C T I O N S
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Base
20. DC IN 9V jack
21. Main base antenna
22. Telephone line jack
23. Main base speaker
24.
25.
(play/stop) key (pages 42 and 44)
(repeat/rewind) key (page 45)
20
21
22
26. Main base charging contacts
27. Menu/clock key (pages 34 and 37)
28. Mic (microphone)
29. Ringer key (page 42)
30. Memo rec (record) key (page 48)
31. Greeting key (page 41)
32. Charge/in use LED
23
32
33
34
35
36
37
33.
34.
35.
(delete) key (page 47)
(skip/fast forward) key (page 46)
(answer on/off) key (page 43)
24
25
26
27
36. Set key (page 34)
37. /volume/select keys
(pages 34 and 42)
/
38
38. Find hs (handset) key (pages 22 and 52)
28 29 30 31
w w w . u n i d e n . c o m
C O N T R O L S & F U N C T I O N S [ 4 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Extra Charging Cradle for Second Handset
39. Charging contacts
40. Charge LED
41. DC IN 9V jack
41
39
40
Terms Used in this Manual
• Standby Mode - The handset may be sitting in or off the cradle, but is NOT in use. The talk/flash key has not
been pressed and there is no dial tone.
• Talk Mode - The handset is off the cradle and the talk/flash key has been pressed, enabling a dial tone.
• CID - Caller ID
• CIDCW - Caller ID on Call Waiting
w w w . u n i d e n . c o m
[ 5 ] T E R M S U S E D I N T H I S M A N U A L
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessibility
Uniden provides a customer service hotline for accessibility questions. If you have a disability and need customer
service assistance or if you have any questions about how Uniden's products accommodate persons with disabilities,
please call the accessibility voice/TTY line:
1-800-874-9314
A representative is available to talk to you M-F, 8:00 am to 5:00 pm, CST. After hours, you can leave a message, and
w w w . u n i d e n . c o m
A C C E S S I B I L I T Y [ 6 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Phone
Do the following steps:
note
A. Choose the Best Location
B. Install the Rechargeable Battery Packs into the Handsets
C. Connect the Main Base and Charging Cradle, and Charge the Handsets
D. Mount the Main Base on a Wall
If your home has
specially wired alarm
equipment connected to
the telephone line, be
sure that installing the
system does not disable
your alarm equipment.
A. Choose the Best Location
When choosing a location for your new phone, here are some important guidelines you should consider:
Avoid heat sources, such as radiators,
air ducts, and sunlight
Avoid noise sources such as a window by
a street with heavy traffic
Avoid television sets and other
electronic equipment
Avoid microwave ovens
If you have questions
about what will disable
your alarm equipment,
contact your telephone
company or a qualified
installer.
Avoid excessive moisture,
extremely low temperatures, dust,
mechanical vibration, or shock
Choose a central location
Avoid personal computers
Avoid other cordless telephones
• The location should be close to both a phone jack and a continuous power outlet (one
which is not connected to a switch).
• The main base and each handset should be kept away from sources of electrical noise such
as motors, microwave ovens, and fluorescent lighting.
• The cradle can be placed on a desk, tabletop, or mounted on a standard wall plate. For
better reception, place the main base as high as possible.
• The main base should be placed in an open area for optimum range and reception.
[ 7 ] I N S T A L L I N G T H E P H O N E
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
B. Install the Rechargeable Battery Packs into the Handsets
Both handsets are powered by rechargeable battery packs. The
battery recharges automatically when the handset is placed in
the main base or charging cradle.
!
Use only the Uniden
(BT-905 or BT-1006)
rechargeable battery
pack supplied with
your cordless
1) Press down on the handset battery case cover (use the finger
indention for a better grip) and slide the cover downward to
remove.
2) Plug the battery pack connector (red & black wires) into the
jack inside the battery compartment.
telephone.
(The connector notches fit into the grooves of the jack only
one way.) Match the wire colors to the polarity label in the
battery compartment, connect the battery and listen for a
click to insure connection.
3) Make sure you have a good connection by slightly pulling on
the battery wires. If the connection is secure, the battery
jack will remain in place.
4) Place the battery case cover back in the handset by sliding it
upwards until it clicks into place.
w w w . u n i d e n . c o m
I N S T A L L I N G T H E P H O N E [ 8 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Connect the Main Base and Charging Cradle,
and Charge the Handsets
1) Connect the AC adapter to the DC IN 9V jack and to a
!
standard 120V AC wall outlet.
2) Place one handset in the main base and the other in the
charging cradle with the keypad facing forward.
•Use only the supplied
AD-314 AC adapter
for the main base and
AD-310 or AD-1010
for the charging
cradle.
3) Make sure the charge/in use LED and charge LED illuminate.
If the LED does not illuminate, check to see that the AC adapter is
plugged in and the handset makes good contact with the cradle's
charging contacts.
Do not use any other
AC adapter.
• Connect each AC adapter to a continuous power supply.
• Place each cradle close to the AC outlet to avoid long
extension cords.
•Do not place the power
cord where it creates a
trip hazard or where it
could become chafed
and create a fire or
electrical hazard.
4) Charge your handsets at least 15-20 hours before plugging the
phone line.
5) Once the handset battery packs are fully charged, connect
the telephone line cord to the TEL LINE jack and a telephone
outlet.
If your telephone outlet isn't modular, contact your
telephone company for assistance.
Modular
[ 9 ] I N S T A L L I N G T H E P H O N E
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
D. Mount the Main Base on a Wall
Standard wall plate mounting
This phone can be mounted on any
standard wall plate.
1) Plug the AC adapter to the DC IN 9V
jack.
2) Route the AC adapter cord through
the molded wiring channel as shown.
3) Plug the AC adapter into a standard
120V AC wall outlet.
6
4) Plug the telephone line cord into the
TEL LINE jack. Route the cord
through the molded wiring channel
as shown.
5
1
6
5) Plug the telephone line cord into the
telephone outlet.
2
6) Align the mounting slots on the
main base with the mounting posts
on the wall. Then push in and down
until the phone is firmly seated.
3
4
w w w . u n i d e n . c o m
I N S T A L L I N G T H E P H O N E [ 1 0 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct wall mounting
If you don't have a standard wall plate, you can mount your phone
directly to the wall. Before doing this, consider the following:
• Avoid electrical cables, pipes, or other items behind the mounting
location that could cause a hazard when inserting screws into the
wall.
• Try to mount your phone within 5 feet of a working phone jack to
avoid excessive cord lengths.
• Make sure the wall material is capable of supporting the weight of
the main base and handset.
• Use #10 screws (minimum length of 1-3/8 inches) with anchoring
devices suitable for the wall material where the main base will be
placed.
1) Insert two mounting screws into the wall, (with their appropriate anchoring device), 3-
15/16 inches apart. Allow about 1/8 of an inch between the wall and screw heads for
mounting the phone.
2) Refer to steps 1 through 6 on page 10 to mount the telephone.
Installing the Beltclip
To attach the beltclip
Insert the beltclip into the holes on each side of the handset. Press down until it clicks.
To remove the beltclip
Pull both sides of the beltclip to release the tabs from the holes.
[ 1 1 ] I N S T A L L I N G T H E P H O N E
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Headset Installation
Your phone may be used with an optional headset. To use this feature,
insert the headset plug into the headset jack.
Your phone is ready for hands-free conversations.
by calling our Parts Department. See page 53.)
w w w . u n i d e n . c o m
I N S T A L L I N G T H E P H O N E [ 1 2 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Register Handsets to the Main Base before Using!
Whichever handset you choose to charge in the main base will automatically register to the
main base.
note
The second handset (charging in the extra charging cradle) MUST also be registered to the
main base before use. Follow the steps below to register the second handset.
•When you charge the
handsets, Caller ID
summary screen and
the name of the
1) Be sure both handsets are fully charged.
handset, HS1 appears.
If HS2 appears, you
are charging the
2) Remove the handset from the charging cradle, and place it in the main base. The charge/
in use LED light on the main base will begin to flash, indicating that the registration is
taking place.
handset No. 2.
3) Wait for at least five seconds, then remove the handset from the main base.
•The charging cradle
can be used to charge
either handset.
4) Press the find hs key on the main base. If both handsets beep, registration is complete. If
one handset does not beep, re-register that handset.
5) Once both handsets are registered, it doesn’t matter which handset is placed in the main
base or the charger.
[ 1 3 ] R E G I S T E R H A N D S E T S T O T H E M A I N B A S E B E F O R E U S I N G !
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
1) You’ll need to re-register the second handset (follow steps on page 13) each time the digital
security code is changed. Refer to page 52 for details regarding the Digital Security Code.
2) When there is a power failure for more than one hour:
note
If power failure occurs (e.g. due to electrical storm or if the unit is unplugged during a
move), both handsets will need to be re-registered. To re-register, follow the same
registration process on page 13.
Make sure to return the
handsets to the cradles
after each phone call.
3) If the second handset’s battery becomes very low, the handset must be recharged for 15-
20 hours and re-registered to the main base.
w w w . u n i d e n . c o m
W H E N T O R E - R E G I S T E R H A N D S E T S [ 1 4 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Setup
There are five basic options that you will need to set up: AutoTalk, CIDCW (Caller ID on Call
Waiting), Area Code, Dial Mode and Language.
CIDCW and Dial Mode options can only be set by using Handset 1. If you try to set by using
Handset 2, you will not see these options listed on the LCD screen.
(Handset 1 shows HS1 in the display while the phone is charging.)
AutoTalk, Area Code and Language options can be set by using either
Handset 1 or Handset 2.
Activating AutoTalk
AutoTalk allows you to answer the phone simply by removing the handset from the cradle.
You do not have to press any keys.
1) When the phone is in standby mode, press and hold the call id/
menu key. The following screen appears.
2) Press the select/channel key to turn AutoTalk on.
3) Press the end key to complete the setting. The handset returns to
standby mode.
Activating Caller ID on Call Waiting
Caller ID allows you to see the name and number of the calling party before you answer the
phone. Caller ID on Call Waiting (CIDCW) lets you see the name and number of a call that
comes in when you are on the line.
[ 1 5 ] B A S I C S E T U P
w w w . u n i d e n . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
You must subscribe to Caller ID service through your local telephone provider to use this
feature.
1) When the phone is in standby mode, press and hold the call id/
menu key. The following screen appears.
2) Press the /vol/
key to select CIDCW.
3) Press the select/channel key to toggle and turn on Caller ID on
Call Waiting.
4) Press the end key and return the handset to the main base to
complete the setting. The handset returns to standby mode.
Entering Your Area Code
If you can make a call by dialing only 7 digits (instead of 10), you can program your local
area code in your phone. If you get a call from within your area code, you'll only see the 7-
digit phone number. If you get a call from outside your area code, you'll see all 10 digits.
1) When the phone is in standby mode, press and hold the call id/
menu key. The following setting screen appears.
2) Press the /vol/
key twice to select Area Code.
3) Press the select/channel key. If an area code was already stored,
the phone will display it.
w w w . u n i d e n . c o m
B A S I C S E T U P [ 1 6 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
4) Use the number keys (0 - 9) to enter the 3-digit area code. If you
make an error, use the delete/transfer key to backspace.
note
5) Press the select/channel key. A confirmation tone sounds.
If your phone system
requires pulse dialing
and you need to send
DTMF tones during a
call, you can
temporarily switch over
to tone dialing. (Refer
to “Tone Dialing Switch-
over” on page 21.)
6) Press the end key to complete the setting. The handset returns to standby mode.
Choosing the Dialing Mode
Your phone can communicate with the telephone network in two different ways: tone dialing
and pulse dialing. These days, most phone networks use a method called tone dialing, so
your phone comes programmed for tone dialing.
If your phone company uses pulse dialing, you'll need to change your phone's dial mode.
There's an easy way to tell: try making a call. If your call connects, your phone's setting is
fine. If not, follow the steps below:
1) When the phone is in standby mode, press and hold the call id/
menu key. The following screen appears.
2) Press the /vol/ key three times to select Dial.
3) Press the select/channel key to set the phone to pulse dialing.
4) Press the end key and return the handset to the main base to
complete the setting. The handset returns to standby mode.
[ 1 7 ] B A S I C S E T U P
w w w . u n i d e n . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Language
You can change the language the menu display uses. Choose from English, French, or
Spanish.
1) When the phone is in standby mode, press and hold the call id/
menu key. The following screen appears.
2) Press the /vol/
key four times to select Language.
3) Press the select/channel key to select Eng, Fr. or Esp.
4) Press the end key to complete the setting. The handset returns to
standby mode.
Selecting the Ring Tone and Volume
Your phone has five different ringer tone/volume combinations you can choose from.
1) With the phone in standby mode, press the
/vol/ or
/vol/ key.
2) The phone will sound the different ring tones at different volumes. To turn the ringer off,
select Ringer Off.
3) When the phone sounds the ring tone and volume you wish to use, press the end key.
w w w . u n i d e n . c o m
B A S I C S E T U P [ 1 8 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Phone
note
Making and Receiving Calls
Making a call
1) Remove the handset from the cradle.
2) Press the talk/flash key.
3) Listen for the dial tone.
4) Dial the number.
OR
1) Remove the handset from the cradle.
2) Dial the number.
3) Press the talk/flash key.
Receiving a call
1) Remove the handset from the cradle. (If AutoTalk is on, the phone will automatically
To turn on the AutoTalk
feature, see “Activating
AutoTalk” on page 15.
answer the call when you pick it up.)
2) Press the talk/flash key.
OR
1) If the handset is off the cradle, press the talk/flash, /tone/ , #/
or any number
*
key. (AutoTalk is on.)
Hanging up
Press the end key or return the handset to the cradle.
[ 1 9 ] U S I N G Y O U R P H O N E
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Transferring a Call
Your cordless phone allows you to transfer outside calls from handset to handset; only one
handset at a time can talk with an outside caller. The second handset cannot go off hook to
listen to conversations or make an outgoing call while the other handset is in use.
note
To transfer a call
If you transfer a call and
it is not picked up after
5 minutes, the call will
be disconnected.
1) During a call, press the delete/transfer key. The call will
automatically be placed on hold and the transfer tone sounds.
2) When the other handset receives the call, the transfer tone
stops. To cancel the transfer and return to the caller, press the
delete/transfer or talk/flash key on the handset.
To receive a transfer call
Pick up the handset from the cradle (when AutoTalk is set to on),
or pick up the handset and press the talk/flash key to answer
the transferred call. Additionally, you can answer the transferred
call by pressing /tone/ , #/
or any number key, (when
*
AutoTalk is set to on).
Redialing the Last Dialed Number
1) Remove the handset from the cradle.
2) Press the talk/flash key.
3) Listen for the dial tone.
4) Press the redial/pause key.
OR
1) Remove the handset from the cradle.
2) Press the redial/pause key.
3) Press the talk/flash key.
w w w . u n i d e n . c o m
U S I N G Y O U R P H O N E [ 2 0 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Earpiece Volume
To change the earpiece volume, press the /vol/
or
note
/vol/ key during a call.
Temporarily Mute Ringer
You can only mute the
handset ringer if the
handset is off the cradle
when the phone starts
ringing.
If the handset is off the cradle while an incoming call is
ringing, simply press the end key to mute the incoming
ring. The ringer will sound with the next incoming call.
Tone Dialing Switch-over
If your telephone company requires pulse dialing, you can
switch over to tone dialing after the call connects. This
feature is useful when you need tone dialing to use any
automated menu systems, such as telephone bank tellers,
telephone prescriptions refills, customer support menus, etc.
If your phone is set to pulse dialing mode, make your call
normally. Once your call connects, press the /tone/
key.
*
Any digits you enter from then on will be sent as tone digits.
When this particular call ends, the phone automatically
returns to pulse dialing mode.
[ 2 1 ] U S I N G Y O U R P H O N E
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Traveling Out-of-Range
During a call, as you begin to move your handset too far from your main base, noise
increases. If you pass the range limits of the main base, your call will terminate within one
minute.
note
The UltraClear PlusTM
true compander circuitry
virtually eliminates
background noise. This
innovative technology,
together with 20
Selecting a Different Channel
If you encounter interference while using your phone, you can manually change the phone´s
channel for clear operation. While using your phone, press the select/channel key. Scanning
appears on the display, indicating the phone is changing to another channel. For more
information on interference, refer to "Radio Interference" on page 61.
different channels,
provides you with the
best possible reception
during all your
Find Handsets
conversations.
To locate the handsets, press the find hs key on
the main base. The handsets beep for 60 seconds.
To cancel paging, press any key on either handset
or the find hs key on the main base.
Paging is also canceled when the phone receives an
incoming call.
w w w . u n i d e n . c o m
U S I N G Y O U R P H O N E [ 2 2 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Call Waiting
If you have Call Waiting, you can receive calls while on the line.
1) If a call comes in while you are on the phone, you will hear
a call waiting tone. If you have CIDCW activated, you will
see the name and number of the incoming caller.
2) Press the talk/flash key to accept the waiting call. After a
short pause, you will hear the new caller.
3) To return to the original caller, press the talk/flash key
again.
You must subscribe to Call Waiting through your local telephone company.
[ 2 3 ] U S I N G Y O U R P H O N E
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Using the Speed Dial Memory
The speed dial memory allows you to store up to 10 names and numbers in each handset. You
can dial these numbers with just a few key presses.
note
The speed dial memory is not limited to phone numbers. You can store any number (up to 20
digits) that you need to enter once your call connects. This is referred to as Chain Dialing.
For example, you can save your bank account number to speed dial memory. When you call
your bank's telephone teller service and are prompted to enter your account number, simply
press the memory key and the speed dial number where you stored your account number.
Then press the select/channel key.
When editing the speed
dial memory, you must
press a key within 30
seconds or the phone
will return to standby
mode. If you return the
handset to the cradle,
the phone will return to
standby mode also.
Storing Names and Numbers in Speed Dial Memory
1) With the phone in standby mode, press the memory key.
2) Enter 0-9 to select the speed dial number where you would like to
store this entry. You can also scroll through the list with the
/
vol/ and
/vol/
keys. Press the select/channel key twice.
3) Store Name appears and a cursor flashes indicating that the
phone is ready for the name to be entered.
If the selected speed dial number is already assigned, the Edit
screen appears. You can select Edit to edit this entry, select
Delete to erase this entry, or select Go Back to choose another
speed dial number.
w w w . u n i d e n . c o m
U S I N G T H E S P E E D D I A L M E M O R Y [ 2 4 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
4) Enter a name according to the instructions below, then press the select/channel key. If no
name is required, go to step 5.
• The name can be up to 13 characters.
note
• Use the #/
and /tone/
keys to move the cursor to the desired location.
*
• Use the delete/transfer key to delete characters as needed.
• Press and hold the delete/transfer key to delete all the characters.
If the next character
uses the same number
key, you must press the
Refer to the letters on the number keys to select the desired characters.
With each press of a numeric key, the displayed character appears in the following order:
upper case letters first, lower case letters next and finally the number corresponding to
the key.
#/
key to move the
cursor over. Otherwise
the next time you press
the number key, it
If you make a mistake while entering a name
changes the character
that was previously set.
Use the /tone/
or #/
key to move the cursor to the incorrect character.
*
Press the delete/transfer key to erase the wrong character. Then enter the correct
character. To delete all characters, press and hold the delete/transfer key.
Number of times key is pressed
For example, to enter Movies.
keys
1
2
3
4
5
6
7
8
9
1) Press 6. Then press the #/
move the cursor to the right.
2) Press 6 six times.
key to
1
2abc
3def
3) Press 8 six times.
4ghi
5jkl
4) Press 4 six times.
6mno
5) Press 3 five times.
6) Press 7 eight times.
7pqrs
8tuv
9wxyz
0oper
[ 2 5 ] U S I N G T H E S P E E D D I A L M E M O R Y
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
5) Store Numberis displayed. The cursor flashes indicating that the
phone is ready for the number to be entered.
6) Use the keypad to enter the phone number; each number can be
up to 20 digits.
If you need the phone to pause during the dialing sequence, press
the redial/pause key to insert a two-second delay between the
numbers. You can enter multiple pauses to increase the delay.
Each pause counts as a digit. The display shows a
pause.
P
for every
When storing numbers into memory, if the handset is idle (i.e., no key is pressed) for more
than 30 seconds, it will beep rapidly, and the phone will return to standby mode.
7) Press the memory key. You will hear a confirmation tone, and the
following screen appears.
Memory storage is complete.
After about 2 seconds, the following screen displays all the speed
dial memory entries.
8) Press the end key to exit memory setup mode. The phone returns
to standby.
w w w . u n i d e n . c o m
U S I N G T H E S P E E D D I A L M E M O R Y [ 2 6 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing Caller ID Messages in Speed Dial Memory
Messages (Caller ID names/numbers) shown in the Caller ID list can be stored in memory
dialing. For way of viewing the Caller ID Message list, see page 30.
note
1) Press the call id/menu key. Select the phone number to be stored
You cannot store a
Caller ID message if no
phone number appears
in the message.
from the Caller ID list by pressing the /vol/ or
/vol/
key.
2) Press the memory key.
3) Enter a number (0 - 9) or press the /vol/ or
/vol/
key to select the memory
location to be stored.
4) Press the select/channel key. You hear a confirmation tone, and
the number is stored in memory. The display returns to the Caller
ID list.
If a number has already been stored in the selected memory
number location, a confirmation screen is displayed.
Press the
/vol/
key to select Yes. Press the select/channel
key to overwrite. The display returns to the Caller ID list.
[ 2 7 ] U S I N G T H E S P E E D D I A L M E M O R Y
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Making Calls from Speed Dial Memory
1) Press the memory key. The handset displays your programmed
speed dial number.
2) Enter the number (0 - 9), or press the
/vol/ or
/vol/
key to select the speed dial number you would like to dial.
3) Press the talk/flash key. Connecting changes to Talk, and the
volume setting and the number selected appear on the display.
Then the displayed number is dialed.
To cancel speed dialing
To cancel speed dialing, press the end key; the handset returns to standby mode. The handset
will also return to standyby mode if the handset is idle (i.e., no key is pressed) for 30
seconds.
w w w . u n i d e n . c o m
U S I N G T H E S P E E D D I A L M E M O R Y [ 2 8 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID and CIDCW (Caller ID on Call Waiting)
You must subscribe to Caller ID service through your local telephone provider to use
this feature. When the telephone rings, the Caller ID feature allows you to view the caller’s
name, phone number, date and time of call. The incoming call information is stored in the
Caller ID record. If the Caller ID service includes the caller´s name, the caller´s name appears
on the display (up to 15 letters).
note
•If you answer a call
before the Caller ID
message is received
(for example, before
the second ring), the
Caller ID message will
not appear.
The date and
time received
Caller's name
Caller's phone number
You may receive any one of the following messages:
When invalid data is received
When a private name is received
When a private number is received
Incomplete Data
•When the call is
received via a
telephone company
that does not offer
Caller ID service, the
caller´s phone number
and name do not
Private Name
Private Number
When an unknown name is received Unknown Name
When an unknown number is receivedUnknown Number
Data errors appear as ¨ ¨.
appear. (This includes
international calls.)
•When the call is
received via a private
branch exchange
(PBX), the caller´s
phone number and
name may not appear.
[ 2 9 ] C A L L E R I D A N D C I D C W ( C A L L E R I D O N C A L L W A I T I N G )
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Viewing the Caller ID Message List
The Caller ID list stores information for up to 30 incoming calls - even unanswered calls. You
can also view the Caller ID list during a call.
note
1) Press the call id/menu key. The summary screen displays the
•In Caller ID operation,
if no key is pressed for
more than 30 seconds,
an error tone sounds
and the telephone
returns to standby
mode.
number of new messages and total messages.
2) Use the /vol/
key to scroll through the messages from the
latest to the earliest, or use the /vol/ key to scroll through
the messages from the earliest to the latest.
3) Press the call id/menu key to return to talk mode, or press the
•Each message can be
up to 15 characters for
the phone number and
the name.
end key to return to standby mode.
•The number of calls
from the same Caller ID
appears next to the
received time. Once
you view the new
message, the number
will be cleared and
disappear.
•During a call, don't
press the end key, or
the call will be
disconnected.
w w w . u n i d e n . c o m
C A L L E R I D A N D C I D C W ( C A L L E R I D O N C A L L W A I T I N G ) [ 3 0 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting Information from the Caller ID List
If the phone receives more Caller ID messages than it can store, the oldest one in the list is
automatically deleted. Caller ID data can also be deleted manually.
note
Deleting a Caller ID message
•While using the Delete
All?or Delete
1) Press the call id/menu key in standby mode. Find the message to
be deleted from the Caller ID list by pressing the
/vol/
or
Message? screen, if no
key is pressed for more
than 30 seconds, an
error tone sounds, and
the handset returns to
standby mode.
/vol/ key.
2) Press the delete/transfer key.
3) Press the /vol/ or
/vol/
key to select Yes, and then
press the select/channel key.
•If you get an incoming
call or page, the
deleting operation is
canceled, and you can
answer the call or
page.
Deleting all Caller ID names/numbers
1) With the phone in standby mode, press the call id/menu key.
2) Press the delete/transfer key.
3) Press the /vol/ or
/vol/
key to select Yes, and then
press the select/channel key.
You hear a confirmation tone and all stored Caller ID messages are
deleted.
[ 3 1 ] C A L L E R I D A N D C I D C W ( C A L L E R I D O N C A L L W A I T I N G )
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Making a Call from the Caller ID List
You can place a call from the Caller ID list.
note
1) Press the call id/menu key in standby mode. Select the phone
number that you want to dial by pressing the
/vol/
or
/
vol/ key.
You cannot make a call
from the Caller ID list if
your cordless phone is
connected to a private
branch exchange (PBX).
2) To have the phone dial a 1before the displayed Caller ID number, press 1. To have the
phone dial the stored area code before the displayed Caller ID number, press 3.
3) Press the talk/flash key. The displayed phone number dials automatically.
Caller ID on Call Waiting (CIDCW)
With CIDCW, you will hear a Call Waiting tone while you are on a call, and the Caller ID data
is displayed. To accept the waiting call, press the talk/flash key (see page 23).
w w w . u n i d e n . c o m
C A L L E R I D A N D C I D C W ( C A L L E R I D O N C A L L W A I T I N G ) [ 3 2 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
The Integrated Answering Device
The cordless phone has a built-in answering system that answers and records incoming calls.
You can also use your answering system to record a conversation, leave a voice memo
message, or to announce a special outgoing message to callers when you're away from your
phone.
Features
• Digital Tapeless Recording
• Up to 13 Minutes of Recording Time
• Call Screening
• Personal or Pre-recorded Outgoing
Message
• Voice Prompts
(English, French or Spanish)
• Time and Day Announcement
• Remote Message Retrieval
• Toll Saver
• Conversation Recording
• Voice Memo
• Selectable Ringer Options
(High, Low or Off)
Digital Tapeless Recording allows you to quickly review, save, or delete any messages you
choose. You will never have to worry about a tape wearing out, jamming, or resetting
improperly.
The Integrated Answering System is easy to use, but please read through all of the
instructions carefully.
[ 3 3 ] T H E I N T E G R A T E D A N S W E R I N G D E V I C E
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Setting Up Your Answering System
note
Answering System Settings
To set the following six functions you must enter the menu mode.
•For your convenience,
voice prompts will
guide you through the
menu mode.
• With the phone in standby mode, use the menu/clock
menu/clock
menu/clock
menu/clock
key to scroll through the menu options. The system
returns to standby and sounds a tone after the last
menu option.
•After the setting, press
• If any of the following occurs during menu setup, the
system returns to standby; you will have to start over
with the procedure you were performing:
-The talk/flash key is pressed
the
(play/stop)
key to exit the menu
mode, or the menu/
clock key to move to
the next menu option.
menu/clock
menu/clock
menu/clock
menu/clock
-The
(play/stop) key is pressed
-10 seconds elapse without a key press
-An incoming call is received
• If the system remains idle for about five seconds after
the announcement, the system returns to standby.
Once the
or /volume/select key is pressed, the
idle time is extended to 10 seconds.
w w w . u n i d e n . c o m
S E T T I N G U P Y O U R A N S W E R I N G S Y S T E M [ 3 4 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Time
The clock on the cordless phone’s answering system starts when power is supplied to the
main base. Follow these steps to set the clock to the correct time.
note
1) With the phone in standby mode, press the menu/
clock key.
•Normally, the system
will return to standby
if it remains idle for 10
The system announces "Time" followed by the
current time and the instructions for setting the
time.
seconds after the
/volume/select
key is pressed. For
setting the time,
or
2) Press the
or /volume/select key until the
correct day is announced. The numbers [ ] through
[ ] are displayed on the main base.
however, the idle time
is extended to two
minutes.
3) Press the set key to select the day.
•Press and hold the
or
/volume/select
key to quickly scroll
through the numbers
on the display.
4) Press the
the correct hour setting. The numbers [ ] through
] are displayed on the main base.
or /volume/select key until you hear
[
5) Press the set key to select the hour.
6) Press the
or /volume/select key until you hear the correct minute setting.
The numbers [ ] through [ ] are displayed on the main base.
7) Press the set key to select the minute.
[ 3 5 ] S E T T I N G U P Y O U R A N S W E R I N G S Y S T E M
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
8) Press the
or /volume/select key until you hear the correct AM or PM setting.
The message counter displays [ ] or [ ].
note
9) Press the set key to select the AM/PM setting.
You hear a confirmation tone followed by the announcement "Time," and the day and time
are then announced for your review. After a few seconds, the system announces “To set
security code, press menu again.”
Setting a Personal Security Code (PIN)
If you want to be able to play your messages from a remote location, you need to enter a
two-digit Personal Identification Number (PIN) code (01-99). To select a PIN, perform the
following steps:
1) With the phone in standby mode, press the menu/clock key twice.
The system announces "Security code," and the current PIN code is announced as it is
displayed on the main base. Then the system announces the instructions for setting the
PIN code.
The PIN code is set to
"80" at the factory.
2) Press the
or /volume/select key until the desired number appears.
3) Press the set key to select the PIN code. You hear a confirmation tone, then the
announcement "Security code" followed by the new PIN code. After a few seconds, the
system announces “To set ring time, press menu again.”
w w w . u n i d e n . c o m
S E T T I N G U P Y O U R A N S W E R I N G S Y S T E M [ 3 6 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Ring Time
The ring time setting allows you to set the number of rings the caller hears before your
answering system plays the outgoing message. You can set the ring time to answer after two,
four, or six rings. If you select Toll Saver [
], the answering system picks up after two
rings if you have new messages, and after four rings if there are none. This way, if you make
a long distance call to check your messages, you can hang up after the second ring to avoid
billing charges.
1) With the phone in standby mode, press the menu/clock key three times.
You hear "Ring time" and the current ring time ([ ], [ ], [ ], [
] Toll saver), and it
is displayed on the main base. Then you hear the guidance for setting the ring time.
2) Press the or /volume/select key until the desired ring time appears.
3) Press the set key to select the new ring time. You hear a confirmation tone, then the
announcement "Ring time" followed by the new ring time. After a few seconds, the system
announces "To set record time, press menu again."
[ 3 7 ] S E T T I N G U P Y O U R A N S W E R I N G S Y S T E M
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Selecting the Message Record Time
You have three record time options: one minute, four minutes, and "Announce only."
"Announce only" answers the call with the preset greeting or your personal greeting but
prevents the caller from leaving a message.
note
After setting the
1) With the phone in standby mode, press the menu/clock key four times.
Announce only feature,
you may want to change
your outgoing message
not to prompt the caller
to leave a message.
However, the
You hear "Record time" and the current recording time ([ ] one minute, [ ] four
minutes, [ ] Announce only, No recording), and it is displayed on the main base.
Then you hear the guidance for setting the record time.
2) Press the
or /volume/select key until the desired time appears.
prerecorded message
changes automatically.
3) Press the set key to select the new recording time. You hear a confirmation tone, then the
announcement "Record time" followed by the new recording time. After a few seconds, the
system announces "To set message alert, press menu again."
Setting the Message Alert Tone
The message alert tone beeps every 15 seconds whenever you have unheard messages. The
tone turns off automatically after you listen to all your new messages. You can also turn off
the message alert tone by pressing any key on the base.
Follow the steps below to turn on the message alert tone:
1) With the phone in standby mode, press the menu/clock key five times.
w w w . u n i d e n . c o m
S E T T I N G U P Y O U R A N S W E R I N G S Y S T E M [ 3 8 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
You hear "Message alert" and the current setting ([
] Off or [
] On), and it is
displayed on the main base. Then you hear the instructions for setting the Message Alert
Tone.
2) Press the
or /volume/select key to make your selection.
3) Press the set key to select the new setting. You hear a confirmation tone, then the
announcement "Message alert" followed by the setting you have selected. After a few
seconds, the system announces "To set language, press menu again."
When the first new message is received, the alert tone will begin to sound.
Selecting the Language
The answering system voice announcements can be heard in English, French or Spanish.
To choose the language of the answering system voice announcements:
1) With the phone in standby mode, press the menu/clock key six times.
You hear the announcement "Language, English" followed by the voice prompts for setting
the language. The current setting ([ ], [ ] or [ ]) appears on the main base.
2) Press the
or /volume/select key to select the desired language.
3) Press the set key. A confirmation tone is heard along with the setting in the language
selected.
[ 3 9 ] S E T T I N G U P Y O U R A N S W E R I N G S Y S T E M
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Setting Your Outgoing Message (Greeting)
When you receive a call, the answering system automatically plays either a preset message or
your own greeting.
Preset message
The following message is prerecorded:
"Hello, no one is available to take your call. Please leave a message after the tone."
If the answering machine is set to announce only, the preset greeting automatically changes
to:
"Hello. No one is available to take your call. Please call again."
See “Selecting the Message Record Time” on page 38 on how to set the announce only
feature.
w w w . u n i d e n . c o m
S E T T I N G U P Y O U R A N S W E R I N G S Y S T E M [ 4 0 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a personal outgoing message (Greeting)
1) With the phone in standby mode, press and hold the greeting key.
You hear the announcement "Record greeting" and a confirmation tone.
note
[
] flashes on the message counter.
•Your greeting must be
more than 2 seconds
and less than 30
2) Start recording your message. You have 30 seconds, and the message counter starts to
count down [ ] to [ ] every second.
seconds to record.
3) When you are finished recording your greeting, press the greeting,
(play/stop) or set
•Position yourself as
near to the main base’s
microphone as possible
and speak clearly when
recording your
key. You hear a confirmation tone, and then your greeting plays back for you.
Choosing between the two outgoing messages
With the phone in standby mode, press the greeting key. Then press the greeting key to play
the current outgoing message. While the outgoing message is playing, press the greeting key
again to switch between the prerecorded greeting and the personal greeting. After the
message finishes playing, a confirmation tone is heard.
outgoing message.
To delete the personal greeting, press the
(delete) key during the announcement and
the system announces "Greeting has been deleted."
[ 4 1 ] S E T T I N G U P Y O U R A N S W E R I N G S Y S T E M
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Setting the Main Base Ringer Volume
The base has three ringer volume settings: high, low, and off. You can change the ringer volume
while in standby mode or while an incoming call is ringing.
note
1) Press the ringer key.
You hear the ringer at the current volume level
Even when the main
base ringer is turned
off, the handset will
still ring.
([
] high, [
] low, [
] off) (if you set the
main base ringer volume to off, "Ringer off " is
announced) and it is displayed on the main base.
2) Press the ringer key repeatedly until the desired
ringer option appears.
3) The system displays the new ringer volume.
Temporarily Mute the Main Base Ringer and Call Screen
Press the
(play/stop) key to temporarily mute the incoming ring and call screen. The
ringer will sound with the next incoming call. To turn the ringer back on for this call, press
the ringer key. To hear the answering machine and screen this call, press the
or /volume/select key.
Adjusting the Speaker Volume Level
You can adjust the volume of the main base speaker by pressing the
or /volume/select
key on the main base. Press the /volume/select key for louder or the /volume/select
key for softer while the main base speaker is being used except for menu mode. The numbers
[
] -[ ] are displayed on the main base indicating the volume levels. [ ] being the
softest and [ ] being the loudest.
w w w . u n i d e n . c o m
S E T T I N G U P Y O U R A N S W E R I N G S Y S T E M [ 4 2 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Answering System On/Off
To turn the answering system on,
press the (answer on/off) key. The
system will announce "Answering
system is on." The current greeting
message will be played, and you hear
a confirmation tone. The message
counter displays the number of
messages stored in memory. If the
display flashes, there are new
messages waiting for you.
To turn the answering system off,
press the (answer on/off) key
again. After the announcement
“Answering system is off,” the
message counter display will no
longer be illuminated.
[ 4 3 ] S E T T I N G U P Y O U R A N S W E R I N G S Y S T E M
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Using Your Answering System
The message counter displays the number of messages stored in memory. If the display
flashes, new messages are waiting for you. The flashing number represents the number of new
messages, not total messages. The cordless phone plays the new messages first; after all the
new messages are played, you can play the old messages.
hint
When the answering system is full, [
] is displayed on the main base, and the system
announces "No remaining time." You should delete some messages so that the system can
record new messages. (Refer to “Deleting a Message” on page 47.)
Playing Your Messages
1) With the phone in standby mode, press the
(play/stop) key. The system announces the
number of new and old messages. The LED
displays the number of new messages, and the
number flashes. The day and time that each
message was received is announced after the
message is played.
To stop playing your
messages, press the
(play/stop) key again at
any time.
2) When all new messages have been played, you
hear a confirmation tone and an announcement
“End of messages.” The message counter
displays the total number of stored messages,
and the system returns to standby.
w w w . u n i d e n . c o m
U S I N G Y O U R A N S W E R I N G S Y S T E M [ 4 4 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
3) After you have reviewed your new messages, you can play your old messages by pressing
the
(play/stop) key again. Once you have listened to a new message, it becomes an
old message. The old messages will be played in the order in which they were received.
Repeating a Message
1) With the phone in standby mode, press the
(play/stop) key to review your messages.
(repeat/rew) key while the message is
The number of stored messages are announced.
2) To repeat the current message, press the
playing. To quickly scroll backwards through a message, press and hold the
rew) key.
(repeat/
3) To go back to the previous message, press the
(repeat/rew) key as soon as a message
begins playing. Each time you press (repeat/rew), the system skips back one message.
4) Press the
standby.
(play/stop) key at any time to stop reviewing messages and return to
[ 4 5 ] U S I N G Y O U R A N S W E R I N G S Y S T E M
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Skipping a Message
1) With the phone in standby mode, press the
The number of messages is announced.
(play/stop) key to review your messages.
2) Press the
(skip/ff) key at any time to skip to the next message.
Each time the
(skip/ff) key is pressed, the system scans forward one message.
If you have several messages, press the
(skip/ff) key repeatedly to find the message
you want to play. To quickly scroll forward through a message, press and hold the
(skip/ff) key.
3) Press the
(play/stop) key at any time to stop reviewing your messages and return to
standby. The message counter shows the number of messages stored in memory.
w w w . u n i d e n . c o m
U S I N G Y O U R A N S W E R I N G S Y S T E M [ 4 6 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting a Message
To maintain maximum record time, delete the old
messages. When you press the (delete) key, you
are permanently deleting the message. Once
deleted, the message cannot be replayed.
1) Press the
messages.
(play/stop) key to review your
2) Press the
(delete) key anytime during the
message to delete.
3) You hear a confirmation tone and the message
is deleted.
You can also delete all the messages.
1) With the phone in standby mode, press the (delete) key. You hear an announcement “To
delete all messages, press delete again.”
2) Press the
(delete) key again.
You hear a confirmation tone and [ ] is displayed on the main base. All the messages are
deleted.
When you try to delete all messages without first listening to your new messages, you hear
several short beeps followed by an announcement “Please playback all messages.” This
protects you from accidentally erasing messages you have not yet reviewed.
[ 4 7 ] U S I N G Y O U R A N S W E R I N G S Y S T E M
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Voice Memo
The voice memo function allows you to record messages
as shorts as two seconds and as long as four minutes.
note
1) With the phone in standby mode, press and hold the
memo rec key.
•When the answering
system is full, [
appears on the message
counter, and recording is
terminated.
You hear an announcement “Record memo message”
]
and a tone. [
] flashes on the message counter.
•Every state has different
regulations governing the
recording of conversations
over the telephone. Make
sure to check your local,
state and federal laws
before using this product
to record any telephone
conversation in order to
determine that your use is
in compliance with such
laws or guidelines.
2) Start your recording.
3) When you have finished, press the
(play/stop),
memo rec or set key to stop recording. You hear a
confirmation tone, and the system returns to standby.
Recording a Conversation
You can record up to 10 minutes of conversation while you are using your phone. Any
conversation that lasts less than two seconds will not be recorded.
•A recorded conversation is
1) During a conversation from the handset, press and hold the memo rec key.
treated as a typical
The unit begins recording with a confirmation tone and [
message counter.
] flashes on the
message and will be added
to the stored messages.
•When recording a
conversation, all dialing
features except for using
call waiting (see page 23)
are disabled. Stop
recording if you need to
enable any other handset
keys.
A beep that can be heard by both parties sounds during recording.
If you receive a call waiting tone while recording a conversation, press the talk/flash
key to accept the waiting call. The recording feature continues recording the new call.
The original call is put on hold.
2) To stop recording, press the
You hear a confirmation tone.
(play/stop) or memo rec key.
w w w . u n i d e n . c o m
U S I N G Y O U R A N S W E R I N G S Y S T E M [ 4 8 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operation
When you are away from home, you can operate your answering system with any touch-tone
telephone. Use this function to check for recorded messages, to play or delete messages,
even record a new greeting message.
tip
For your convenience
remote operation cards
are provided for you to
use while away from
home (located in the
back of this manual).
1) Call your telephone number.
2) During the greeting message, press 0 and enter your PIN code (see page 36).
3) The answering system announces the current time and the number of messages stored in
memory. Then you hear "To play incoming message, press zero two.
For help, press one zero."
4) You may continue to listen to the voice prompts, or you may select a command from the
following chart:
note
Once you enter the
remote access menu,
you must enter a
command within 15
seconds, or the
answering system
automatically hangs up
and returns to standby.
[ 4 9 ] U S I N G Y O U R A N S W E R I N G S Y S T E M
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Command
Function
Repeat a Message
Command
Function
Answering System On
Memo Record/Stop*
Greeting Message Record/Stop*
Answering System Off
Voice Prompts
0 then 1
0 then 2
0 then 3
0 then 4
0 then 5
0 then 6
0 then 7
0 then 8
0 then 9
1 then 0
Play Incoming Messages
Skip a Message
Delete a Message
Stop Operation
*For Memo Record and Greeting Message Record functions, the first time you enter the
corresponding command, it starts the Recording function. If you want to stop the
recording, enter the command again.
5) After all of the voice prompts have been played, you hear intermittent beeps indicating
that the system is in the command waiting mode. You may enter another command at this
time from the chart.
6) When you are finished, hang up to exit the system. The answering system automatically
returns to standby.
w w w . u n i d e n . c o m
U S I N G Y O U R A N S W E R I N G S Y S T E M [ 5 0 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn on the Answering System Remotely
If you have forgotten to turn on your answering system, you can turn it on remotely from
any touch-tone telephone.
1) Call your telephone number.
2) Wait ten rings until the system answers. You hear intermittent beeps.
3) Press 0 and then enter your PIN code. The answering system announces the number of
messages stored in memory. You hear "To play incoming message, press zero two. For help,
press one zero."
4) Press 0 then 6 to turn the answering system on. You hear the outgoing message and a
confirmation tone.
5) Hang up the phone; subsequent calls will be answered by the system.
[ 5 1 ] U S I N G Y O U R A N S W E R I N G S Y S T E M
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Changing the Digital Security Code
To protect you against misbilled calls which might result from your phone being activated by
TM
other equipment, the cordless phone provides AutoSecure (which electrically locks your phone
TM
when each handset is in the cradle) and Random Code digital security which automatically
selects one of over 262,000 digital security codes for each handset and the main base.
If the handset battery pack is completely discharged or the battery pack is removed, the digital
security code will be lost. If this happens, a new security code is set automatically the next time
the battery pack is charged. In the rare situation that you suspect another cordless telephone
is using the same security code, you can change the code.
1) Remove the handset from the cradle. Press and hold the find hs key on the main base.
2) While holding the find hs key, place the handset in the main base, and leave the handset
in the main base for more than three seconds.
3) Remove the handset from the main base. Then place the second handset in the main base
and wait for more than three seconds. No need to holding the find hs key this time.
4) Press the talk/flash key on one handset. Once you make sure Talk appears on the display,
press the end key. Then, try with the second handset. If each handset displays Talk, a
new security code is set. Otherwise, return to step 1 and try again.
w w w . u n i d e n . c o m
C H A N G I N G T H E D I G I T A L S E C U R I T Y C O D E [ 5 2 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Note on Power Sources
Low battery alert
When the battery pack is very low and needs to be charged, the phone is
programmed to eliminate functions in order to save power. If the phone is not in
use, Low Battery appears on the LCD and none of the keys will operate.
If the phone is in use, Low Battery flashes and the handset beeps. Complete your
conversation as quickly as possible and return the handset to the cradle for
charging.
Information stored in the phone's memory will be retained for 30 minutes after
the battery pack is removed. This includes all setup information, last number dialed, speed dial memory, and the CID
list.
Even when the battery pack is not being used, it will gradually discharge over a long period of time. For optimum
performance, be sure to return the handset to the cradle after a telephone call.
Battery replacement and handling
When the operating time becomes short even after a battery is recharged, please replace the battery.
With normal usage, your battery should last about one year. A replacement battery may be purchased by calling
1-800-554-3988 (Mon - Fri 8 am to 5 pm, CST).
Warning: To avoid the risk of personal injury or property damage from fire or electrical shock, only use the Uniden
battery model and Uniden adapter model specifically designated for this product.
Caution
Power Failure
During the period that the power is off, you will not
be able to make or receive calls with the telephone.
• Use only the specified Uniden battery pack (BT-905 or BT-1006).
• Do not remove the battery from the handset to charge it.
• Never throw the battery into a fire, disassemble it, or heat it.
• Do not remove or damage the battery casing.
[ 5 3 ] N O T E O N P O W E R S O U R C E S
w w w . u n i d e n . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Talk and Standby Times
With average use, your handset battery provides approximately 6 hours of talk time and approximately 7 days of
standby time. When your handsets are not being used and are left off of their charging cradles, the battery will
gradually discharge. You can achieve optimum battery life and performance by returning the handset to the charging
cradle after each use. If the handset is left off of the charging cradle, the actual talk time duration will be reduced
respective to the amount of time the handset is off of the charging cradle.
Cleaning the battery charging contacts
To maintain a good charge, clean the charging contacts on
the handset once a month.
Dampen a cloth with plain water. Gently rub the damp cloth
over the charging contacts until all visible dirt is removed.
Dry the contacts thoroughly before returning the handset
to the base.
Caution
Do not use paint thinner, benzene,
alcohol, or other chemical products.
Doing so may discolor the surface of
the telephone and damage the finish.
w w w . u n i d e n . c o m
N O T E O N P O W E R S O U R C E S [ 5 4 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
The phone complies with FCC Parts 15 and 68.
Operating temperature: -10°C to +50°C (+14°F to +122°F)
AC Adapter Information
(For the main base)
AD-314
120V AC 60Hz
9V DC 350 mA
(For the charging cradle)
AC Adapter part number:
Input Voltage:
Output Voltage:
AD-310 or AD-1010
120V AC 60Hz
9V DC 210mA
Battery Information
Battery part number:
Capacity:
BT-905
600mAh, 3.6V
BT-1006
500mAh, 3.6V
or
Frequency
924.516925 - 926.704425 MHz
2,405.155942 - 2,411.718441 MHz
• To avoid damage to the phone use only Uniden AD-314, AD-310 or AD-1010 and BT-905 or BT-1006 with
your phone.
• If the handset is left off the cradle, the actual talk mode duration will be reduced respective to the amount of
time the handset is off the cradle.
Recharge your phone on a regular basis by returning the handset to either cradle after each phone call.
When the operating time becomes short, even after the battery is recharged, please replace the battery.
With normal usage, the battery should last about one year.
A replacement Uniden adapter or battery may be purchased by calling 1-800-554-3988 (Mon - Fri 8 am to 5 pm, CST).
Specifications, features, and availability of optional accessories are all subject to change without prior notice.
[ 5 5 ] G E N E R A L I N F O R M A T I O N
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
Troubleshooting
If your phone is not performing to your expectations, please try these simple steps first. If these steps do not solve
your problem, please call our Customer Hotline at 1-800-297-1023. (Mon - Fri 7 am to 7 pm, Sat/Sun 9 am to 5 pm,
CST. Phone support is closed on holidays.)
Symptom
Suggestion
The charge/in use LED or
charge LED won't illuminate
when the handset is placed in
the cradle.
• Make sure the AC adapter is plugged into the cradle and wall outlet.
• Make sure the handset is properly seated in the cradle.
• Make sure the charging contacts on the handsets are clean.
The audio sounds weak and/or
scratchy.
• Move the handset and/or main base away from metal objects or appliances and try again.
• Press the select/channel key in the talk mode to help eliminate background noise.
• Make sure that the handset is not too far from the main base.
Can't make or receive calls.
• Re-register both handsets (see page 13).
• Check both ends of the telephone line cord.
• Make sure the AC adapter is plugged into the main base and wall outlet.
• Disconnect the AC adapter for a few minutes. Then reconnect it.
• Change the digital security code (see page 52).
• Make sure that the handset is not too far from the main base.
• Check the dialing mode used by your telephone company.
w w w . u n i d e n . c o m
T R O U B L E S H O O T I N G [ 5 6 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Suggestion
The handset doesn't ring or
receive a page.
• Re-register both handsets (see page 13).
• The battery pack may be weak. Charge the battery for 15-20 hours.
• The handset may be too far from the main base.
• Place the main base away from appliances or metal objects.
• Change the digital security code (see page 52).
• Check the battery pack to ensure there is a secure connection.
• Make sure ringer volume isn't set to "off."
Severe noise interference.
• Keep both handsets away from microwave ovens, computers, remote control toys, wireless
microphones, alarm systems, intercoms, room monitors, fluorescent lights, and electrical
appliances.
• Move the main base to another location or turn off the source of interference.
The Caller ID does not display.
• The call was answered before the second ring.
• The call was placed through a switchboard.
• Charge the handset.
• Your Caller ID service may not be active; contact your local telephone service provider.
Handset No.1 or No.2 is not
working.
• Make sure the battery pack is connected to the handset and fully charged.
• Re-register the non-functional handset.
Unavailable message is displayed • Make sure the other handset is not already in use. Both handsets cannot be in talk mode at the
on the LCD screen of the
handset.
same time.
• Place the handset in the main base for at least 5 seconds to re-register to the main base.
• Make sure the handset is not too far from the main base when trying to use.
[ 5 7 ] T R O U B L E S H O O T I N G
w w w . u n i d e n . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Suggestion
The handset doesn’t
communicate with the main base • Re-register both handsets (see page 13).
or the other handset.
No 3-way conversation.
• Only one handset at a time can talk with an outside caller. To allow the other handset to talk to
the caller, transfer the call.
The answering system does not • Make sure the AC adapter is plugged into wall outlet.
work. • Make sure the answering system is turned on.
The answering system does not • Set the record time to either the one minute or four minute option.
record any messages.
• The memory may be full. Delete some or all of the saved messages.
Messages are incomplete.
• The incoming messages may be too long. Remind callers to leave a brief message.
• The memory may be full. Delete some or all of the saved messages.
After a power failure, the
outgoing message is deleted.
• Record your personal outgoing message again. The default message should remain.
• Adjust the speaker volume on the main base.
No sound on the main base
speaker during call monitoring
or message playback.
Cannot access remote call-in
features from another touch-
tone phone.
• Make sure you're using the correct PIN code.
• Make sure that the touch-tone phone you're using can transmit the tone for at least two
seconds. If it cannot, you may have to use another phone to access your messages.
w w w . u n i d e n . c o m
T R O U B L E S H O O T I N G [ 5 8 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Liquid Damage
Moisture and liquid can damage your cordless phone. In case of accidental submersion, please follow these steps.
Case
Action
If the handset or base is exposed to
moisture or liquid, but it only affects the
exterior plastic housing.
Wipe off the liquid, and use as normal.
If moisture or liquid has entered the
Handset:
plastic housing (i.e., liquid can be heard 1.Remove the battery cover and leave it off for ventilation
in the phone or liquid has entered the
handset battery compartment or vent
openings on the base).
2.Remove the battery pack by disconnecting
3.Leave the battery cover off and the battery pack disconnected for at least 3 days
4.Once the handset is completely dry, reconnect the battery pack and the battery cover.
5.Recharge the handset’s battery pack for 20 hours before using again.
Base:
1.Disconnect the AC adapter from the base unit, cutting off electrical power.
2.Disconnect the telephone cord from the base unit.
3.Let dry for at least 3 days.
IMPORTANT: You must unplug the telephone line while recharging the battery pack to
avoid charge interruption.
CAUTION:
DO NOT use a microwave oven to speed up the drying process. This will cause permanent
damage to the handset, base and the microwave oven.
After following these steps, if your cordless telephone does not work, please call our
Customer Service Hotline at 1-800-297-1023.
[ 5 9 ] T R O U B L E S H O O T I N G
w w w . u n i d e n . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Uniden works to reduce lead content in our PVC coated cords in
our product and accessories.
product. It is designed to be connected to a compatible modular
jack that is also compliant. See installation instructions for
details.
Precautions!
Before you read anything else, please observe the following:
Warning!
Warning!
The cords on this products and/or accessories contain lead, a
chemical known to the State of California to cause birth defects or
other reproductive harm. Wash hands after handling.
Uniden America Corporation DOES NOT represent this unit to be
waterproof. To reduce the risk of fire, electrical shock, or damage
to the unit, DO NOT expose this unit to rain or moisture.
The REN is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone line
may result in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not exceed
five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the
local telephone company. For products approved after July 23,
2001, the REN for this product is part of the product identifier
that has the format US:AAAEQ##TXXXX. The digits represented by
## are the REN without a decimal point (e.g., 03 is a REN of 0.3).
For earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the
telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice
isn’t practical, the telephone company will notify the customer as
soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
Important Safety Instructions
When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric shock
and injury to persons, including the following:
Rechargeable Nickel-Cadmium Battery Warning
•This equipment contains a rechargeable nickel-cadmium battery.
•Cadmium is a chemical known to the State of California to cause
cancer.
•The rechargeable nickel-cadmium battery contained in this
equipment may explode if disposed of in a fire.
•Do not short-circuit the battery.
•Do not charge the rechargeable nickel-cadmium battery used in
this equipment in any charger other than the one designed to
charge this battery as specified in the owner’s manual.
Using another charger may damage the battery or cause the
battery to explode.
1. Do not use this product near water, for example, near a bath
tub, wash bowl, kitchen sink or laundry tub, in a wet basement
or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock
from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of
the leak.
4. Use only the power cord and batteries indicated in this manual.
Do not dispose of batteries in a fire. They may explode. Check
with local codes for possible battery disposal instructions.
5. Do not disassemble any component of this product.
The telephone company may make changes in its facilities,
equipment, operations or procedures that could affect the
operation of the equipment. If this happens the telephone
company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
Please follow instructions for repairing, if any (e.g. battery
replacement section); otherwise do not substitute or repair any
parts of the device except as specified in this manual.
Connection to party line service is subject to state tariffs. Contact
the state public utility commission, public service commission or
corporation commission for information. This equipment is
hearing aid compatible.
Rechargeable Nickel-Cadmium
Batteries Must Be Recycled or
Disposed of Properly
SAVE THESE INSTRUCTIONS
•Uniden voluntarily participates in an RBRC® industry program to
collect and recycle nickel-cadmium batteries at the end of their
useful life, when taken out of service within the United States.
The RBRC® program provides a convenient alternative to placing
used nickel-cadmium batteries into the trash or municipal waste
stream, which is illegal in some areas.
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions. Do not
open or mutilate the battery, and disconnect the battery before
shipping this product.
•Through the RBRC® program, Uniden makes it easy for you to
drop off the used battery at local retailers of replacement nickel-
cadmium batteries. You may also contact your local recycling
center for information on where to return the used battery.
Please call 1-800-8-BATTERY for information on Ni-Cd battery
recycling in your area. Uniden's involvement in this program is
part of its commitment to protecting our environment and
conserving natural resources.
The FCC Wants You To Know
Should you experience trouble with this equipment, please
contact Uniden customer service at 800-297-1023. If the
equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the
equipment until the problem is resolved.
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the bottom of this
equipment is a label that contains, among other information, a
product identifier in the format US:AAAEQ##TXXXX. If requested,
this number must be provided to the telephone company.
An applicable Universal Service Order Codes (USOC) certification
for the jacks used in this equipment is provided (i.e., RJ11C) in
the packaging with each piece of approved terminal equipment.
A plug and jack used to connect this equipment to the premises
wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this
NOTICE: According to telephone company reports, AC electrical
surges, typically resulting from lightning strikes, are very
destructive to telephone equipment connected to AC power
sources. To minimize damage from these types of surges, a surge
arrestor is recommended.
•RBRC® is a registered trademark of the Rechargeable Battery
Recycling Corporation.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
w w w . u n i d e n . c o m
P R E C A U T I O N S & W A R R A N T Y [ 6 0 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Changes or modifications to this product not expressly approved
by Uniden, or operation of this product in any way other than as
detailed by the owner's manual, could void your authority to
operate this product.
OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some
states do not allow this exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion may
not apply to you.
Cordless Telephone Privacy
Cordless telephones are radio devices. Communications between
the handset and base of your cordless telephone are accomplished
by means of radio waves which are broadcast over the open
airways.
LEGAL REMEDIES: This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state. This
warranty is void outside the United States of America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after
following the instructions in the owner's manual you are certain
that the Product is defective, pack the Product carefully
(preferably in its original packaging). Disconnect the battery from
the Product and separately secure the battery in its own separate
packaging within the shipping carton. The Product should include
all parts and accessories originally packaged with the Product.
Include evidence of original purchase and a note describing the
defect that has caused you to return it. The Product should be
shipped freight prepaid, by traceable means, to warrantor at:
Because of the inherent physical properties of radio waves, your
communications can be received by radio receiving devices other
than your own cordless telephone unit. Consequently, any
communications using your cordless telephone may not be private.
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation. Privacy of communications, may not be
ensured when using this phone.
One Year Limited Warranty
Important: Evidence of original purchase is required for warranty
service.
To insure the safety of users, the FCC has established criteria for
the amount of radio frequency energy various products may
produce depending on their intended usage. This product has been
tested and found to comply with the FCCís exposure criteria. For
body worn operation, the FCC RF exposure guidelines were also
met when used with the Uniden accessories supplied or designed
for this product. Use of other accessories may not ensure
compliance with FCC RF exposure guidelines and should be
avoided.
WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden")
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the
original retail owner, this Uniden Product to be free from defects
in materials and craftsmanship with only the limitations or
exclusions set out below.
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
WARRANTY DURATION: This warranty to the original user shall
terminate and be of no further effect 12 months after the date of
original retail sale. The warranty is invalid if the Product is (A)
damaged or not maintained as reasonable or necessary, (B)
modified, altered, or used as part of any conversion kits,
subassemblies, or any configurations not sold by Uniden, (C)
improperly installed, (D) serviced or repaired by someone other
than an authorized Uniden service center for a defect or
malfunction covered by this warranty, (E) used in any conjunction
with equipment or parts or as part of any system not
manufactured by Uniden, or (F) installed or programmed by
anyone other than as detailed by the owner's manual for this
product.
(800) 297-1023, 7:00 a.m. to 7:00 p.m. CST,
Monday through Friday; 9:00 a.m. through 5:00 p.m. CST,
Saturday and Sunday (phone support is closed on holidays).
Radio Interference
Radio interference may occasionally cause buzzing and humming
in your cordless handset, or clicking noises in the base. This
interference is caused by external sources such as TV, refrigerator,
vacuum cleaner, fluorescent lighting, or electrical storm. Your unit
is NOT DEFECTIVE. If these noises continue and are too
distracting, please check around your home to see what
appliances may be causing the problem. In addition, we
recommend that the base not be plugged into a circuit that also
powers a major appliance because of the potential for
interference. Be certain that the antenna on the unit is fully
extended when needed.
STATEMENT OF REMEDY: In the event that the product does not
conform to this warranty at any time while this warranty is in
effect, warrantor will either, at its option, repair or replace the
defective unit and return it to you without charge for parts,
service, or any other cost (except shipping and handling) incurred
by warrantor or its representatives in connection with the
performance of this warranty. Warrantor, at its option, may replace
the unit with a new or refurbished unit. THE LIMITED WARRANTY
SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY
PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES
ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER
EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS
WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT
In the unlikely event that you consistently hear other voices or
distracting transmissions on your phone, you may be receiving
radio signals from another cordless telephone or other source of
interference. If you cannot eliminate this type of interference, you
need to change to a different channel.
Finally, it should be noted that some cordless telephones operate
at frequencies that may cause interference to nearby TVs and
VCRs. To minimize or prevent such interference, the base of the
cordless telephone should not be placed near or on top of a TV or
VCR. If interference is experienced, moving the cordless telephone
farther away from the TV or VCR will often reduce or eliminate the
interference.
[ 6 1 ] P R E C A U T I O N S & W A R R A N T Y
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . u n i d e n . c o m
I.C. Notice
TERMINAL EQUIPMENT
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation, IC, before the registration number signifies that
registration was performed based on a Declaration of Conformity indicating that Industry Canada technical
specifications were met. It does not imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The
REN assigned to each terminal equipment provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of
all the devices does not exceed five.
RADIO EQUIPMENT
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were
met.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device. “Privacy of communications may not be ensured when using this telephone”.
w w w . u n i d e n . c o m
I . C . N O T I C E [ 6 2 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
Charging the battery pack . . . . . .9
Cleaning contacts . . . . . . . . . . .54
Clock . . . . . . . . . . . . . . . . . . .35
Connect the cradle . . . . . . . . . . .9
Controls and functions . . . . . 3, 4, 5
Redial . . . . . . . . . . . . . . . . . . 20
Register handsets to the main base be-
fore using . . . . . . . . . . . . . . . 13
Remote operation . . . . . . . . . . 49
Ring time . . . . . . . . . . . . . . . . 37
Index
A
AC adapter information . . . . . . . 55
Answering system
Deleting a message . . . . . . . . 47
Playing a message . . . . . . . . 44
Recording a conversation . . . . 48
Repeating a message . . . . . . . 45
Skipping a message . . . . . . . . 46
Turning on/off . . . . . . . . . . . 43
D
Dial mode . . . . . . . . . . . . . . . .17
Digital security code . . . . . . . . .52
S
Second handset . . . . . . . . . . . . 13
Speed dial memory
E, F, G, H, I, J, K, L
Earpiece volume . . . . . . . . . . . .21
Find handset . . . . . . . . . . . . . .22
General information . . . . . . . . .55
Greeting . . . . . . . . . . . . . . . . .40
Headset installation . . . . . . . . .12
I.C. Notice . . . . . . . . . . . . . . .62
Installing the phone . . . . . . . . . .7
Interference . . . . . . . . . . . . . .61
Liquid damage . . . . . . . . . . . . .59
Making calls from speed dial memory
. . . . . . . . . . . . . . . . . . . . 28
Storing names and numbers in speed
dial memory . . . . . . . . . . . 24
B
Basic setup . . . . . . . . . . . . . . 15
Battery pack
Information . . . . . . . . . . . . . 55
Installing . . . . . . . . . . . . . . . 8
Preparing and charging . . . . . . 8
Replacement and handling . . . 53
Beltclip installation . . . . . . . . . 11
T, U
Talk and Standby Times . . . . . . . 54
Technical information . . . . . . . . 55
Tone dialing switch-over . . . . . . 21
Transferring a call . . . . . . . . . . 20
Traveling out-of-range . . . . . . . 22
Troubleshooting . . . . . . . . . . . 56
M, N, O, P, Q
C
Making a call . . . . . . . . . . . . . .19
Menu mode . . . . . . . . . . . . . . .34
Message alert . . . . . . . . . . . . . .38
Outgoing message . . . . . . . . . . .40
Personal security code (PIN code) 36
Precautions . . . . . . . . . . . . . . .60
Call transfer feature . . . . . . . . . 20
Call waiting . . . . . . . . . . . . . . 23
Caller ID service . . . . . . . . . . . 29
Call waiting . . . . . . . . . . . . . 23
Deleting . . . . . . . . . . . . . . . 31
Making a call . . . . . . . . . . . . 32
Viewing . . . . . . . . . . . . . . . 30
Channel . . . . . . . . . . . . . . . . . 22
V, W, X, Y, Z
Voice memo . . . . . . . . . . . . . . 48
Volume control
Base . . . . . . . . . . . . . . . . . . 42
Handset . . . . . . . . . . . . 18, 21
Wall mounting . . . . . . . . . . . . . 10
Warranty . . . . . . . . . . . . . . . . 61
R
Receiving a call . . . . . . . . . . . .19
Record time . . . . . . . . . . . . . . .38
[ 6 3 ] I N D E X
w w w . u n i d e n . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operation Card
C
U
T
C
U
T
REMOTE OPERATION CARD
MEMORY LOCATION MEMO
Name Phone Number
Memory
Location
Remote access away from home
Turn on the answering system remotely
1. Call your phone number from a 1. Call your phone and let it ring
1*
2
touch-tone phone.
10 times until it answers.
2. Press 0 and enter your PIN
code.
3. Press 0 then 5 to stop
the announcement.
4. Press 0 then 6 to turn the
answering system on.
2. During the outgoing message,
press 0 and enter your PIN
code. The answering system
announces the number of
messages stored in memory
and the voice prompts. The
phone stands by for you to
enter a command.
3
4
5
3. To quit, hang up the phone.
C
U
T
C
U
T
MEMORY LOCATION MEMO
Name Phone Number
REMOTE OPERATION CARD
Memory
Location
Remote access away from home
Turn on the answering system remotely
1. Call your phone number from a 1. Call your phone and let it ring
1*
2
touch-tone phone.
10 times until it answers.
2. Press 0 and enter your PIN
code.
3. Press 0 then 5 to stop
the announcement.
4. Press 0 then 6 to turn the
answering system on.
2. During the outgoing message,
press 0 and enter your PIN
code. The answering system
announces the number of
messages stored in memory
and the voice prompts. The
phone stands by for you to
enter a command.
3
4
5
3. To quit, hang up the phone.
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operation Card
C
U
T
C
U
T
MEMORY LOCATION MEMO
Name Phone Number
Task
Repeat a Message
Play Incoming Messages
Skip a Message
Delete a Message
Stop Operation
Answering System On
Memo Record/Stop
Key
0
1
2
3
4
5
6
7
8
9
0
Memory
Location
0
0
0
0
0
0
0
0
1
6
7
8
Greeting Message Record/Stop
Answering System Off
Voice Prompts
9
10
C
U
T
C
U
T
MEMORY LOCATION MEMO
Name Phone Number
Task
Repeat a Message
Play Incoming Messages
Skip a Message
Delete a Message
Stop Operation
Answering System On
Memo Record/Stop
Key
0
0
0
0
0
0
0
0
0
1
1
2
3
4
5
6
7
8
9
0
Memory
Location
6
7
8
Greeting Message Record/Stop
Answering System Off
Voice Prompts
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
At Uniden, we'll take care of you!
Thank you for purchasing a Uniden product. If you have any questions or problems,
please do not return this product to the place of purchase.
Having Trouble?
call our Customer Hotline at 1-800-297-1023, Mon-Fri, 7 a.m. to 7 p.m. or Sat/Sun, 9 a.m. to
5 p.m. CST. (Phone support is closed on holidays.)
Need a Part?
To order headsets, additional handsets, replacement batteries or other accessories, visit
Help for our Special Needs Customers
If you need special assistance due to a disability or have questions on the accessibility
features of this product, please call 1-800-874-9314 (voice or TTY)
May be covered under one or more of the following U.S. patents:
4,797,916 5,426,690 5,434,905 5,491,745 5,493,605 5,533,010
5,574,727 5,581,598 5,650,790 5,660,269 5,661,780 5,663,981
5,671,248 5,696,471 5,717,312 5,732,355 5,754,407 5,758,289
5,768,345 5,787,356 5,794,152 5,801,466 5,825,161 5,864,619
5,893,034 5,912,968 5,915,227 5,929,598 5,930,720 5,960,358
5,987,330 6,044,281 6,070,082 6,125,277 6,253,088 6,314,278
6,418,209 6,618,015 6,671,315 6,714,630 6,782,098 6,788,920
6,788,953 6,839,550 6,889,184 6,901,271 6,907,094 6,914,940
6,953,118 7,023,176
Other patents pending.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
