INSTALLATION GUIDE
Firmware Version A7J
Advanced 2-Way
Remote Vehicle Starter
With Security System
AUTOMATIC AND MANUAL
TRANSMISSION MODELS
WWW.ULTRASTARTERS.COM
See website for a full size printable version of this manual.
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation
is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved
by the part responsible for compliance void the user’s authority
to operate this devise.
TECH SUPPORT
Western Canada 1 800 279-0636
E-Mail: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
WIRING DIAGRAM
Starter
Heater
(+) 30amp Output
(+) 30amp Output
(+) 30amp Input
(+) 30amp Input
(+) 30amp Output
(+) 30amp Output
Yellow
Green
Red
Red
White
Blue
1
3
5
2
Main Power
Main Power
Selectable
Ignition 1
4
6
YELLOW
ORANGE
BROWN
FACTORY RE-ARM
STARTER DISABLE
FACTORY DISARM
TRUNK RELEASE
(-)500ma Output
(-)500ma Output
(-)500ma Output
(-)500ma Output
1
2
3
5
RED/WHITE
WHITE/VIOLET
GREEN
GREEN/WHITE
PURPLE
PINK
4
6
8
(-)500ma Output (-) WHEN RUNNING
(-) DOOR TRIGGER
Negative Input
HOOD PIN INPUT
(+) DOOR TRIGGER
Negative Input
Positive Input
7
9
BRAKE SWITCH
Positive Input
Negative Input
(A/C) Input
(-) Input
10
BLACK
GROUND
TACH INPUT
GLOW PLUG
11
13
BLUE/WHT
BLUE
12
WHITE
PARK LIGHTS
PARK BRAKE
Positive 15amp
Negative Input
14
BLACK/WHITE
10
12
4th Ch. Programmable
(-)500ma Output Dome Light Supervision
(-)500ma Output
Buttons #1 & # 3
White /Green
Black
11
Positive 3 amp
Negative Input
Siren Output
White /Blue
Red
13
Trunk Pin Input
STARTER DISABLE RELAY
TEMPERATURE SENSOR (OPTIONAL)
FM ANTENNA WITH DUAL LED’S
BUILT-IN PROGRAM SWITCH.
4 PIN
BLUE
*The antenna must be connected for the system to operate.
SIDE VIEW
Green
Red
Blue
Pink
Door Lock
(-)500ma Output
(+)500ma Output
12volt Inverter Output
4 PIN
RED
(-)500ma Output Door Unlock
(-)500ma Output
Passenger Door Unlock
(-)Input
Blue
Sensor Pre-Warn Input
Sensor Full-Warn Input
Sensor Ground Output
Sensor 12V+ Power Output
4 PIN
WHITE
(-) Input
Green
Black
Red
(-)500ma Output
(+)500ma Output
4 PIN
WHITE
SATELLITE LINK PLUG
(-)Disarmed/Cranking/LED
Horn Honk/ 5th Channel
Green
Pink
Blue
4 PIN
WHITE
(-)500ma Output
(-)500ma Output
Programmable
Buttons #2 & # 3
(+) Input
(+)Disconnect
***500ma outputs are low current and are designed to activate relays
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
INSTALLATION TIPS
Components
- Control module.
- 2 way Remote transmitter.
- Antenna with built in Program Button and LED’s.
- 6 pin main harness with dual 30amp power inputs.
- 14 pin harness.
- 4 pin square harness.
- 4 pin keyless entry harness.
- 4 pin Aux. sensor harness.
- Multi-tone siren.
- Hood pin safety switch.
- Hood and window stickers.
- Installation guide and Owner’s manual.
Recommended Pre-Installation Procedures
BEFORE STARTING INSTALLATION:
- Discuss the optional features with the customer.
- Take a few minutes to review the installation and owners manuals.
- Check if the vehicle has a factory security or anti-theft system.
*If equipped, inform the customer of addition parts and labour.
- Do a walk around the vehicle and check for any damage.
- If installing a LED discuss the placement with customer before installing.
Note: This remote starter is designed for fuel injected and diesel engines.
Recommended Installation Procedures
Proper Connections - Remote Starters can handle loads of up to 30 amps for extended periods of time. It
is CRITICAL to insure that ALL high current connections are properly soldered and insulated with quality
electrical tape. Failing to insure proper connections will result in warranty being VOID and can result in a FIRE.
The manufacturer is not responsible for any such damages. It only takes a few more minutes to do the job
RIGHT.
Under Hood Connections - Route the hood pin and tach wires through the firewall into the engine
compartment. Always try to pull the wires through a factory rubber grommet. If drilling through the firewall, BE
CAREFUL. Check for obstructions on both sides of the firewall. After drilling use a snap in grommet to protect
the wires from sharp edges.
Installing the External Long Range Antenna - To insure the best possible reception, place the
antenna in the center of the windshield, behind the rear view mirror. Before attaching to the glass ensure that
the surface is clean and dry. For best results with range, place the antenna below the tint screen. Run the
cable under the headliner and behind the A-pillar panel. Be careful not to pinch the antenna cable. Plug the
antenna into the BLUE connector on the Control Module.
NOTE: This step is not used on Alarm Only Units with no External Antenna.
Mounting The Control Module - Never mount the module in the engine compartment. Select a location
under the dash to install the main module. Be certain that the module is securely attached and does not
obstruct any serviceable areas. Do not force or jam the module into tight places instead of mounting. The
module must be free from all moving parts such as brake, clutch and gas pedal linkages. Do not place the
module directly in front of a heater vent.
Testing The System - When the installation is complete, it will be necessary to test that the system is
working correctly. The system’s default programming will work on the majority of vehicles, but might need to be
adjusted for some applications. If the installation requires special timing or additional features, proceed to
ATTENTION: The Hood Pin Switch MUST always be connected!!
Program Mode.
Note: Always inform user to place system in Service Mode before any service work is performed
on the vehicle.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
WIRING CONNECTORS
6 Pin Power Connector
Yellow
Green
Red
Red
Blue
White
Starter 30amp output
Heater 30amp output
12 power 30amp input
12 power 30amp input
Ignition 1 30amp output
Selectable 30amp output
12volts during crank only.
12volts in accessory. Off during start.
Constant 12volt power at ignition harness.
Constant 12volt power at ignition harness.
12volts in ignition and start positions.
Jumper Selectable. See Page 5.
14 Pin Connector
Yellow
Re-Arm
0.75sec Pulse With Lock And On Shutdown.
Negative While Locked - **Starter Program Mode.
0.75sec Pulse With Unlock And Before Start.
Trunk Release - Active When button 2 is held.
Negative Output While Running.
Orange
Brown
Red/White
(-) Output
Disarm
3rd CH
White/Violet (-)Running
Green
Purple
Green/White Hood Pin
(-) Door
(+) Door
Negative Door Trigger Input - Manual Trans And Alarm.
Positive Door Trigger Input - Manual Trans And Alarm.
Negative Hood Pin Input - MUST BE CONNECTED!!
Positive Brake Input - MUST BE CONNECTED!!
System Ground Input - MUST BE CONNECTED!!
Tach Signal Input - MUST BE CONNECTED!!
Programmable Input - DIESEL ONLY. **Programmable.
Positive Park light Output - 10 Amp Max.
Pink
Black
Blue/White
Blue
White
Brake
Ground
Tach
Glow Plug
Park Lights
Black/White Park Brake
Negative Park Brake Input - Manual Transmission Models Only.
4 Pin Connector Square
White/Green Channel 4
Black Dome Light
White/Blue Siren
Programmable Output. Press buttons #1 and #3 See Page 9.
Negative Output For Dome Light Supervision.
Positive Output For Siren.
Red
Trunk Pin
Negative Input For Trunk Pin Switch.
4 Pin Connector Red
Green
Red
Blue
Pink
Door Lock
12 Volts
Door Unlock
2nd Unlock
Door Lock Output - Programmable - See Page 8.
Low Current Output. Use With Voltage Inverter
Door Unlock Output - Programmable - See Page 8.
Door Unlock Output - Programmable - See Page 8.
3 Pin Connector White
Green
Pink
Blue
(-) Disarmed
Horn/ Chan.5
(+) Disconnect
Programmable Output. (-) when disarmed, when cranking and LED.
Programmable Output. Press buttons #2 and #3.
(+) Disconnect Or Instant Start Trigger.
Jumper Selections
The jumpers control the output on the white wire from the
six pin harness. Place the jumpers in the above order to
change the output.
Output on White wire Jumper position
Second Starter
Second Accessory
Second Ignition
Position 1
Position 2
Position 3
Note: The default setting is second ignition.
Back View Of Module
3 2 1
Jumpers
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
QUICK START INSTALL
6 Pin Power Connector
Yellow
Green
Red
Red
Blue
White
Starter Output
Heater Output
12 power Input
12 power Input
Ignition 1 Output
Selectable Output
Connect To The Vehicles Starter Wire.
Connect To The Vehicles Accessory Wire.
Connect to Constant 12 Volt Power Source- High Current.
Connect to Constant 12 Volt Power Source- High Current.
Connect To the Vehicles Primary Ignition.
Select Jumper Position (If Necessary). See Page 5.
14 Pin Power Connector
Black
Pink
White
System Ground
Brake Switch
Park Lights
Connect To Chassis Ground.
Connect To (+) When Brake is Applied.
Connect To (+) Park Light System.
Connect To Hood Pin Switch.
Green/White Hood Pin
Blue/White
White/Blue
Green or
Purple
Tach
Siren
(-) Door Input
(+) Door Input
Connect To Tach Source.
Connect To (+) Siren (4-pin square harness)
Connect the Green wire to a (-) door pin system.
Connect the Purple wire to a (+) door pin system.
Manual Transmissions Only
Black/White Park Brake
Manual transmission vehicles must have a “M” Series Remote Starter Installed. Manual Transmission Units Must
Connect Park Brake Switch. (-) When Brake is applied.
Be Placed Into Reservation Mode To Operate. See Page 12.
Step 2- Plug-In The Module
When all the connections are done, the control module can be plugged in. Before connecting the control module,
make sure the ignition is in the OFF position. Plug in the 6 pin harness then the 14 pin followed by any other
connectors that were used.
Step 3- Auto Tach Learn
1) Make all the required wire connections and plug-in the Unit.
**The park lights should flash twice upon power up.
2) Turn the Ignition Key ON. (Park Lights will turn on).
3) Start the vehicle, LED’s on the antenna will come on to confirm tach signal is detected**, then after two to 40
seconds the park lights will turn off then flash twice to confirm tach learning.
* The system will flash the park lights seven times if not tach learned and the start button is
pressed. The system must be tach learned before remote starting.
** If the LED’s do not come on during tach learn, a proper tach signal was not detected.
*** A system reset must be preformed before the tach can be re-learned. (Page. 7)
Note: If the park lights do not flash in auto tach learn mode it may be that the first ignition wire (Blue) is connected
to a wire that turns off during crank. If the ignition connection is good, it may be necessary to connect to a
different tach source. For best results connect the tach wire to the coil pack or to a fuel injector wire. If
necessary See Page 11. for Tach Adjustment.
Activate Self Learning Impact Sensor
1) Press Button #1 on the remote 5 times, once every second. The siren will chirp 3 times and the park lights will
come and stay ON. (If this does not happen, wait five seconds and repeat step 1)
2) While the park lights are on, strike the vehicle three times at the desired level to trigger the alarm.
3) The siren will respond with one chirp each time a impact is detected by the Shock Sensor.
4) Press the button #1 to exit Shock Sensor learning.
Your Basic Install Is Complete!
NOTES:
1) If the unit does not start, check the starter is not in Tach Lock Out or in Program
Your Basic Installation is Now Complete!!
2) If the vehicle still does not start, check all connections and check for factory
Mode.
security.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
PROGRAMMING
Programming Overview
Program mode allows you to adjust the settings and options of your system.
Your system has been intelligently designed by installers with years of experience. The system’s default settings
do not require any program changes in most cases. However, this system does incorporate a highly advanced
programming system that includes 4 menus with numerous options and settings that can be easily adjusted for
custom installations and applications.
Menu 1 - User Settings - Page 8
This program menu contains settings that adjust the way the system operates for the user.
Menu 2 - Alarm Settings - Page 9
This program menu contains settings that adjust the way the system operates for the user.
Menu 3 - Starter Settings - Page 10
This menu controls features and settings associated with remote car starter applications.
Menu 4 - Tach Settings - Page 11
This menu allows the programming of the tach signal and the manual adjustment of that setting.
Entering Program Mode
To Enter Program Mode
1) Make sure ignition is in the off position.
2) Within three seconds turn the key ON - OFF - ON - OFF - ON. Leave in the “ON” position.
3) Press and release the Program Button on the antenna one time.
4) The park lights will come on and the siren will chirp to confirm entering Program Mode.
5) Select the Desired Program Menu:
st
Press Button #1
Press Button #2
Press Button #3
Press Button #4
User Options See Page 8
Alarm Option See Page 9
Remote Start Options See Page 10
Tach Adjustment Menu See Page 11
6) The selected mode will be confirmed by a siren chirp and one park light flash.
7) The Program Menu may be changed at any time by pressing the transmitter buttons as above, this allows
the installer to change a setting from one menu, then quickly jump to another menu and change another
setting without re-entering the Program Mode.
8) To exit Program Mode, Turn the ignition key “OFF” or wait 30 second and the system will exit automatically.
This will be confirmed by one long siren chirp and park light flash.
Note: If unit does not enter Program Mode, turn the ignition off then repeat steps 1-4.
** The first ignition(Blue wire) MUST be connected to the vehicle’s first ignition wire. If it is not connected it
will not be possible to enter the Program Modes.
Changing the Programmable Settings
To Select and Change A Program Setting:
1) Enter Program Mode.
2) Select the desired Program Menu. (See pages 8 - 11)
d
3) Press & release the Program Button the correct number of times to select the desired Program
Setting(as listed on pages 8 - 11). The park lights will flash and the siren will chirp to indicate the current
setting that is selected.
4) Press and hold the Program Button until the parking lights / siren confirm the selected setting. The park
lights will flash and the siren will chirp to indicate the option selected within the setting.
5) Turn the ignition key “Off” to exit Program Mode.
Note: This procedure is listed in detail below each program setting on pages 8 - 11.
SYSTEM RESET
STEP 1 - Within three seconds turn the key ON-OFF-ON-OFF-ON (Leaving Key ON).
STEP 2 - Press and release the Program Button.
STEP 3 -The park lights will turn ON.
STEP 4 - Press the Program Button a second time and hold for 8 seconds until the park lights flash and the
siren will chirps three times. The system is now re-set to factory defaults.
Note: Reset to defaults does not delete the transmitters from memory.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
PROGRAMMING
Setting 1- Ignition Auto Lock
1 Ignition Lock & Unlock Enabled
2 Ignition Lock Only
*3 Ignition Auto Lock Disabled
1 Flash
2 Flashes
3 Flashes
Doors Lock / Unlock when the key is turned On/ Off
Doors Lock when ignition key is turned ON only
Doors do not Lock or Unlock with Ignition key
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 2- Horn Honk Settings
1 Lock & Unlock chirps Disabled
2 Lock & Unlock chirps Enabled
*3 All chirps enabled
1 Flash
2 Flashes
3 Flashes
Chirps for Panic and Car Finder Mode only.
Chirps for Lock, Unlock, Panic and Car Finder Mode Only.
Chirps for Lock, Unlock, Start, Panic and Car Finder Mode.
Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 3- Door Lock Options
1 Double Pulse Unlock
2 3 Second Lock & Unlock
*3 0.75 Second Pulses
1 Flash
2 Flashes
3 Flashes
Single .75sec.Lock pulse and double Unlock Pulse
3 second pulses for Lock & Unlock
0.75 second pulses for Lock and Unlock
*See setting 7 for short unlock and disarm pulse durations
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 4 -Sensor - Enable / Disable
1 Sensors Disabled
* 2 Sensors Enabled
1 Flash Impact Sensors Disabled
2 Flashes Impact Sensors Enabled - Normal Operation
Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 5 - Passive / Active Arming
1 Passive Arming
2 Active Arming With Rearm
* 3 Active Arming
1 Flash
2 Flashes
3 Flashes
System Auto Arms 30 seconds after last door is closed
Auto-Arms if unlock is pressed and no door is opened within 30sec
Alarm Arms Only with Transmitter
Press the Program Button 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 6 - Active / Passive Locks
1 No Auto-Lock with Passive Arm
1 Flash
Doors do not auto-lock with passive arming
*2 Doors Auto-Lock with Passive 2 Flashes
DOORS LOCK WHEN PASSIVE ARMING
Press the Program Button 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 7 - Door Unlock & Disarm Pulse Duration
1 Short Pulses
*2 Normal
1 Flash
2 Flashes
125ms pulses with Unlock and on disarm output. (.125 second)
750ms pulses with Lock, Unlock and disarm output. (.75 second)
Press the Program Button 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
PROGRAMMING
Setting 1 - Service Mode (Valet Mode)
1 Secure Valet Active
2* Normal Valet Active
1 Flash
2 Flashes
Turn the ignition on and hold the Program Button for 15 seconds
Turn the ignition on and hold the Program Button for 5 seconds
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 2 - Parking Light Output
1 30 Second Park Lights
2 Negative Park Lights
3* Normal Parking Lights 3 Flashes
Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
1 Flash
2 Flashes
Park Lights on for 30 seconds on disarm
Switches the Park Light and the Trunk Release (3rd Channel) Outputs
2 Park Light Flashes on disarm
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 3 - Horn Honk Timing - Pink wire on 3-pin white
1
2
5ms
20ms
1 Flash
2 Flashes
3 Flashes
Short (Quiet) Pulses
Long (Loud) Pulses
Normal (Medium) Pulses
*3 10ms
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 4 - 4th Channel Settings- White/Green wire on 4-pin square
1
2
Pulsed
Latched
1 Flash
2 Flashes
3 Flashes
Pulsed for 0.75 seconds upon 4th Channel Activation
Latched until repeated or ignition “ON”
Active for as long as buttons are held on Transmitter
*3 Active
Note: To activate the 4th channel output, press and hold transmitter buttons #1 and #3 at the same time. The siren
will chirp once to confirm 4th channel activation.
Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 5 -Car Jack Mode
1 Door & Button
2 Door, Button 4
*3 Car Jack OFF
1 Flash
2 Flashes
3 Flashes
Car Jack is activated upon Button 4 or Door open while Ignition is “ON”
Car Jack is upon Button 4 or Door open or ignition “ON” and Ignition
No Car Jack Functions
Press the Program Button 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 6 - Horn / 5th Channel - Pink wire on 3-pin white
1 5th Channel
2 Horn Honk 2
*3 Horn Honk 1
1 Flash
2 Flashes
3 Flashes
Pulsed output when activated by buttons #2 & #3 held for 2 seconds
Horn Honk Output - Full Alarm ONLY
Horn Honk with Arm & Disarm Chirps
Note: To operate the 5th channel, this setting must be programmed for setting #1. To activate the output press
buttons #2 and #3 together for two seconds..
Press the Program Button 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 7 -Programmable Output - Green Wire on 3-pin white
1 LED Output
2 Low Crank
*3 (-) Disarmed
1 Flash
2 Flashes
3 Flashes
The output will pulse (-) when armed for activation of an LED.
The output will come on (-) during crank duration.
Negative while disarmed.
Press the Program Button 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
Enter Starter Program Mode - See Page 7 for details on entering program mode
Setting 1- Special Door Lock/ Unlock Operations
1 Type `1
2 Type 2
3* Normal Operation 3 Flashes
1 Flash
2 Flashes
Unlock pulse before start, lock pulse after start and after shutdown
Lock pulse after remote starter shuts off
No additional re-lock pulses
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 2- Gas/ Diesel Mode- Blue Wire on 14-Pin
1 Negative Glow Plug
2 Timed Delay
3* Gas/ Glow Plug (+)
1 Flash
2 Flashes
3 Flashes
Waits a Maximum of 30 second before starting.
Ignition ON for 10 seconds before engaging remote starter
If no diesel input is detected the vehicle will start after two seconds.
Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 3- Rearm Output- Yellow Wire on 14-Pin
1 Type 1
2 Type 2
3* Factory Re-arm
1 Flash
2 Flashes
3 Flashes
Pulse after start and with lock
Pulse after start only
0.75 second pulse with lock and after shutdown
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 4- Run Time
1 30 Min Run Time
2 45 Min Run Time
3* 15 Min Run Time
1 Flash
2 Flashes
3 Flashes
Remote Starter runs for 30min when activated
Remote Starter runs for 45min when activated
Remote Starter runs for 15 min when activated
Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 5-Maximum Crank Time
1 10 Seconds
2 3 Seconds
3* 5 seconds
1 Flash
2 Flashes
3 Flashes
10 sec Max time that starter will stay engaged
3 sec Max time that starter will stay engaged
5 sec Max time that starter will stay engaged
Press the Program Button 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 6- Starter Kill / Aux. Horn - Orange wire on 14-Pin Con.
1 Horn Output
2* Starter Disable
1 Flash
2 Flashes
Pulsed output to activate negative horn.
Negative output while the system is armed
Press the Program Button 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Setting 7- Sensor Disconnect - Blue wire on 3-Pin Con.
1 Positive Start Input
2 Positive Disconnect
3* Positive Disconnect 3 Flashes
1 Flash
2 Flashes
Positive pulse will activate remote starter.
Alarm will trigger if disconnected from 12 volts.
Alarm will trigger if disconnected from 12 volts.
Press the Program Button 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Continued on next page...
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
Setting 8- Safety Start Mode
1 Safety ON
2* Safety OFF
1 Flash Must press the start button twice to remote start vehicle
2 Flashes Press the start button once to remote start vehicle.
Press the Program Button 8 times to select setting 8 (This will be confirmed by 8 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
PROGRAM MODE - TACH SETTINGS
Setting 1 - Method 1- Auto Tach Learning. See page 7.
Setting 1- Method 2- Low Idle Tach Learning
This option is used for vehicles that maintain a HIGH or erratic idle after starting and need more that 10
seconds to establish a stable idle.
Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program Button on the antenna 1 time.
Step 2 - Enter Program Menu 4 - Press Button #4 on the remote.
Step 3 - Start Vehicle - Using the ignition key, make sure not to turn the key off at any time or your will exit programming.
Step 4 - Press the Program Button - One time (LED- flashing in single cycles) then press and hold button for (5sec).
Step 5 - Release Program - Led should come on steady to indicate correct tach signal the park light will flash to confirm.
Setting 2- Adjust For Over-Crank
Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Program Menu 4 - Press Button #4 on the remote.
Step 3 - Press the Program Button - 2 times (Led will start flashing 2 times).
Step 4 - Press and Hold Program - For 5 seconds until parking lights flash (each time lights flash tach is reduced).
Step 5 - Release Program - Exit Program Mode and remote start to test.
Setting 3- Adjust For Under-Crank
Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Program Menu 4 - Press Button #4 on the remote..
Step 3 - Press the Program Button - 3 times (Led will start flashing 3 times).
Step 4 - Press and Hold Program - For 5 seconds until parking lights flash (each time lights flash tach is increased).
Step 5 - Release Program - Exit Program Mode then remote start to test.
Transmitter Programming
Step 1 - Within three seconds turn the ignition Key ON-OFF-ON-OFF-ON - Leaving Key ON
Step 2 - Press and hold the Program Button - Parking Lights will come ON
**if the park-lights do not come on at this point, turn the key off for 5 seconds, the repeat step 1.
Step 3 - Continue to hold the Program Button the park lights will go out. (Do not release program switch)
Step 4 - The siren will chirp five time quickly, Press button 1 on the remote transmitter (ensure the
“#” symbol is not displayed on the LCD) the park light will flash to confirm transmitter programming.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
OPERATIONS
Transmitter Operation
Press Once to Lock / Unlock Doors and arm/disarm the alarm.
Press 2nd Time (within 3 sec.) and Hold for Constant Lock Output.
Press and hold for 3 seconds to activate Panic Mode.
Press again to disable panic when activated.
1
While running with the key, press the button to activate Idle Mode.
Press and Hold for Trunk / Aux Output
*Note this will also unlock doors and disarm alarm
2
3
Press Once for Start - (2 Times if programmed for Safety Start).
Press and Hold for 3 seconds while running to turn off.
While running with the key, press the button to activate Idle Mode.
2
3
1
4
Press and Release for Status Check.
Hold for 3 seconds to enter User Programmable Features
While running with the key, press and release to activate Turbo Timer Mode.
4
Press and release button #4 then press and hold button #3 for three seconds to
activate/Deactivate the Timer Mode
4 - 3
Press both buttons for 3 seconds to activate Car Finder Mode or 5th channel (see
page 9, setting 6)
2 & 3
1 & 3 Press both buttons for 1-2 seconds to activate 4th Channel (see page 9, setting 4)
Quick Timer (Selects Last Programmed Start Interval)
1. Enter Transmitter Program Mode.
2. The Telephone Icon will begin to flash on the LCD screen.
3. Press Button #3 and the Telephone Icon will come on solid and the key Icon will begin to flash.
4. Press Button #4 to exit Transmitter Program Mode.
5. The remote starter will now start in the last programmed start interval.
Note: Timer Mode will reset if the ignition key is turned to the “On” position. If this occurs the above
steps will have to be repeated.
Reservation Mode - Manual Trans.
Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most
installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during the
activation of the remote starter. Never disconnect or alter the switch to be always bypassed. Always use a “M”
Series Remote Starter on a manual transmission vehicle.
Never install a automatic Remote Starter model into a manual transmission vehicle. It is not recommended to
install a remote starter on a convertible type vehicle. If doing so It is highly recommended that a radar sensor is
installed to cover the proximity of the gear shift lever. If the radar sensor is tripped the remote starter will exit
Reservation Mode.
To enter Reservation Mode, the following steps must be followed.
Step 1 - While the vehicle is running, place the transmission in neutral and apply the parking brake.
Step 2 - Press and release the brake pedal. The park lights will activate.
Step 3 - Turn the ignition key off and the vehicle will stay running.
Step 4 - Exit the vehicle and close the door. The vehicle will then shut off*.
Step 5 - The vehicle can now be safely remote started.
* If the vehicle has a dome light delay, the vehicle may stay running until the dome light turns off. This is normally
no longer than 30 seconds. Reservation Mode will automatically be exited if the doors of the vehicle are opened.
The set-up mode will then have to be repeated . Reservation Mode Must be set-up each time the vehicle is
parked.
Note: If the vehicle is not in Reservation Mode and the Start button is pressed, the system will
flash the park lights four times slowly.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
OTHER FEATURES
ATTENTION: THE SYSTEM MUST BE PLACED INTO SERVICE MODE BEFORE ANY UNDER HOOD
SERVICING IS DONE TO THE VEHICLE. IT IS THE RESPONSIBILITY OF THE VEHICLE’S OWNER TO
INSURE THAT THIS IS DONE. THE MANUFACTURER ACCEPTS NO RESPONSIBILITY FOR
ACCIDENTAL STARTING WHILE VEHICLE IS BEING SERVICED.
System Service Mode (Valet) - By Remote
This feature will disable the system from the remote transmitter. Use this feature must be
used when having the vehicle serviced. ( Oil change, Tune-up etc.)
ACTIVATE Service Mode (User Programmable Feature)
1 - Press and hold button #4 for 3 seconds. (The remote will beep twice)
2 - Press button #1 Five times or until the ? starts flashing on the LCD screen.
3 - Press button #3 and the ? symbol will come on solid.
4 - Press button #4 to exit User Program Mode.(System Is Now In Service Mode)
5 - The siren will chirp once and the LED’s on the antenna will come on solid.
DEACTIVATE Service Mode
1 - Press and hold button #4 for 3 seconds. (The remote will beep twice)
2 - Press button #1 Five times or until the ? starts flashing on the LCD screen.
3 - Press button# 2 and the ? symbol will turn off.
4 - Press button# 4 to exit User Program Mode.(Serice Mode is Deactivated)
5 - The siren will chirp once and the LED’s on the antenna will turn off.
Note: Remote starter functions will be disabled and the LED will be “On” steady.
The door locks and the trunk release will still be operational.
Emergency Service Mode - (Valet Mode)
This feature will disable the system except for locking and unlock functions.
This mode can also used if a remote is lost, damaged or if the system malfunctions.
ENTERING SERVICE MODE
1.Turn the ignition key to the “On” position then press and hold the Program Button on the
antenna for 5 seconds or until the siren chirps 5 times.
Ignition
“On”
EXITING SERVICE MODE
1.Turn the ignition key to the “On” position then press and hold the Program Button for 5
seconds or until the siren chirps 2 times.
Note: Remote starter functions will be disabled and the LED will be “on” steady.
The door locks and the trunk release will still be operational.
7 sec.
Battery Replacement
When the Battery Icon on the remote indicates that the battery is low the battery should be changed
promptly. Replace with quality 1.5volt “AAA” battery.
Slide
Lift
+
.
1
-
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
OPERATIONS
Lock Doors And Arm The Alarm
1. Press and release Button #1 on the Remote Transmitter.
2. The park lights will flash and the siren will chirp one time.
3. The remote will beep once and the doors will lock.
4. The LOCK icon will appear on the LCD display of the remote.
5. The LED’s on the antenna will start flashing within five seconds.
Unlock Doors And Disarm The Alarm
1. Press and release Button #1 on the remote transmitter.
2. The park lights will flash 2 times and the siren will chirp twice.
3. The remote will beep twice to confirm.
4. The doors will unlock.
5. The UNLOCK icon will appear on the LCD display of the remote
6. The LED’s on the antenna will stop flashing within five seconds.
Trunk Release
1. Press and hold the Trunk Release button (Button #2) for three seconds.
2. The doors will unlock, continue to hold for another three seconds and the Trunk Release will
Activate. The Trunk Release will then be confirmed by 2 park light flashes.
3. The remote will beep once then beep twice to confirm the Trunk Release was activated. The
Trunk icon will then appear on the LCD screen for 5 seconds.
4. For safety reasons, the Trunk Release output will be disabled and will not activate when
ignition key is in the “On” position.
Car Finder Mode / Optional 5th Channel
Car Finder Mode.
1. Press and hold Buttons #2 and # 3 together for two seconds.
2. The system will flash the park lights and chirp the siren five times.
3. The remote will beep and display the systems current status.
5th Channel Activation (Must be programmed - see page 9 setting 6)
1. Press and hold Buttons #2 and # 3 together for two seconds.
2. The park lights will flash.
3. The 5th channel output will activate. The remote will beep and display the systems current
status.
Panic Mode
ACTIVATE PANIC MODE
1.Press Button #1 for three seconds.
2.The park lights will flash and the siren will activate.
PANIC MODE DISABLE
- Press Button #1 to disable the Panic Mode and lock the doors.
- Press Button #1 to disable the Panic Mode and unlock the doors.
Note: Panic Mode will stay activated until disabled by the remote transmitter.
4th Channel Activation - See Page 9 Setting 4
ACTIVATE Channel 4 (White/Green) Wire on 4 pin Connector
1.Press Buttons #1 & #3 together for 1-2 seconds.
2.The 4th Channel output will activate in either a pulsed, latched or as long as held format
depending on how the system is programmed in Program Mode 2, Setting 4.
Details available on page 9, Mode 4 (4th Channel)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
OPERATIONS
Remote Start
1.Press and release Button #3 on the Remote Transmitter.
2.The Park lights will flash and the siren will chirp one time.
3. The remote will beep 3 times and the Key Icon will begin flashing.
4.When the vehicle has started, the system will flash the park lights four times and then
remain “On” while the vehicle is running.
5. The Runtime Bar Graph will appear on the LCD screen and begin counting down.
6. The vehicle will continue to run for the programmed runtime. (Normally 15 minutes).
Extended Run Time
1.Press and release Button #3 while the vehicle is running by the remote starter..
2.The park lights will flash and the siren will chirp one time to confirm that the runtime has
been extended. The system will reset the run time, (Normally 15 minutes).
Remote Stop
1.Press and hold Button #3 for three seconds. The remote starter will shut down.
2.The park lights will flash and the siren will chirp two times.
3. The transmitter will beep to verify the status of the alarm. (Armed or Disarmed)
Note: Pressing the brake pedal or opening hood will also stop the vehicle.
Idle Mode
1.Press and release Button #1 while the vehicle is running by the ignition key.
2.The park lights will turn on and the siren will chirp once.
3. The Remote will beep and the Run Time Bar Graph will light up.
4.Turn the ignition key “Off” and the vehicle will continue to run.
5. Exit the vehicle and leave it running safely without the keys in the ignition.
Note: Always lock the doors while the vehicle is left running.
Timer Mode
1. Press and release Button #4, then press and hold Button #3 for 5 seconds.
2. The Park lights will turn “On” and the start cycle can be selected.
1 hour cycle or 0C
2 hour cycle or -5C
3 hour cycle or -15C Press Button #3
4 hour cycle or -25C Press Button #4
Press Button #1
Press Button #2
1 Park light flash
2 Park light flashes
3 Park light flashes
4 Park light flashes
3.The system will start the vehicle at selected start cycle for up to 24 hours.
TO CANCEL TIMER MODE
1.Press and release Button #3, then press and hold Button #4 seconds.
2.The park light will flash and the siren will chirp two times.
3. Starting the vehicle with the key or by the remote will also cancel Timer Mode.
Start Fault Indicator
If the Key Icon in the remote’s Program Menu is flashing, the remote starter has been
disabled. This can be because of various inputs including hood open, brake active, tach
lockout or the system is in Service Mode.(Valet Mode)
When the remote start button is pressed in this mode, the remote will respond by giving 3
beeps and flashing the Key Icon in the Program Window. The Key Icon on the top of the
display will not be illuminated.
Note: The vehicle’s start fault condition must be corrected in order to remote start.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
RELAY DIAGRAMS
Negative Type Door Locks
Vehicle
Lock/Unlock
Switch
Lock
To Control
Relay or
Actuators
Un
lock
Green
Blue
Positive Type Door Locks
Vehicle
Lock/Unlock
Switch
Un
lock
Lock
Fused +12V*
87
87
87a
Green
Blue
87a
86
86
85
85
30
30
To Control Relay
or Actuator
5 Wire / Reverse Polarity Type Door Locks
Fused +12V*
87
87a
87
87a
Green
Blue
86
86
85
85
30
30
Vehicle
Lock/Unlock
Switch
Lock
x
Cut
To Actuator
Un
lock
x
Cut
* Always install an inline fuse on the power inputs to the relays. Do not use the power output on the keyless entry
harness to supply power for relays.
Built-in Starter Disable
IG2
ACC
Off
IG1
Start
Cut
To Starter Motor
or Relay
x
Note: Connect the Starter Wire (Yellow)
to the starter motor side of the starter
disable.
Starter Disable Harness
Brown wire with spade
connectors.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|