Operator’s Manual
MM23016
Rev. C, Apr/08
M/A-COM
M7200 Series
Digital Mobile Radio
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
TABLE OF CONTENTS
Page
1
2
SAFETY SYMBOL CONVENTION....................................................................................................9
RF ENERGY EXPOSURE INFORMATION ...................................................................................10
2.1
RF ENERGY EXPOSURE AWARENESS, CONTROL INFORMATION, AND OPERATION
2.1.1 Federal Communications Commission Regulations......................................................10
2.2.1 Mobile Antennas (Vehicle Installations).......................................................................11
2.2.2 Mobile Antennas (Motorcycle Installations).................................................................12
2.2.3 Approved Accessories ...................................................................................................13
2.2.4 Contact Information.......................................................................................................13
2.2
3
OPERATION SAFETY RECOMMENDATIONS............................................................................14
3.1
3.2
TRANSMITTER HAZARDS.....................................................................................................14
SAFE DRIVING RECOMMENDATIONS................................................................................14
4
5
6
OPERATING RULES AND REGULATIONS..................................................................................15
4.1 OPERATING TIPS.....................................................................................................................15
PRODUCT DESCRIPTION................................................................................................................16
5.1 REMOTE CONTROL HEAD OPERATION.............................................................................16
CHANGE OPERATING MODE ........................................................................................................17
6.1
6.2
CHANGE FROM OTP MODE...................................................................................................17
CHANGE TO OTP MODE.........................................................................................................17
7
OPENSKY OPERATION....................................................................................................................18
7.1
7.2
CH721 FRONT PANEL COMPONENTS .................................................................................18
POWER UP AND VOLUME CONTROL .................................................................................19
7.2.1 Power Up.......................................................................................................................19
7.2.2 Volume Control.............................................................................................................20
SELF-TEST.................................................................................................................................20
LOGIN TO THE NETWORK ....................................................................................................20
LOG OFF THE NETWORK.......................................................................................................21
TURNING THE RADIO OFF....................................................................................................21
MENU DISPLAY AND CONTROL AREA..............................................................................21
RADIO STATUS ICONS...........................................................................................................22
DWELL DISPLAY.....................................................................................................................22
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10 PERSONALITY .........................................................................................................................22
7.10.1 Profiles...........................................................................................................................22
7.10.2 Talk Groups...................................................................................................................23
7.11 ALERT TONES..........................................................................................................................24
7.12 BASIC MENU STRUCTURE....................................................................................................24
7.13 DUAL-TONE MULTI-FREQUENCY.......................................................................................27
7.14.1 Password Entry..............................................................................................................27
7.14.2 DTMF Overdial .............................................................................................................28
7.15 CHANGING THE ACTIVE PROFILE......................................................................................28
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
TABLE OF CONTENTS
Page
7.18 STEALTH MODE ......................................................................................................................28
7.18.1 Enabling Stealth Mode ..................................................................................................29
7.18.2 Disabling Stealth Mode .................................................................................................29
7.19 ADJUSTING SIDE TONE AUDIO LEVEL..............................................................................29
7.20 CHANGE OPERATING MODE................................................................................................29
7.21 RECEIVING AND TRANSMITTING VOICE CALLS............................................................30
7.21.1 Receiving a Voice Call ..................................................................................................30
7.21.2 Transmitting a Voice Call..............................................................................................30
7.22 ADJUSTING AUDIO TREBLE LEVEL ...................................................................................30
7.23 INTERCOM MODE ...................................................................................................................31
7.24 TALK GROUP LOCK OUT.......................................................................................................31
7.24.1 Lock Out a Talk Group..................................................................................................32
7.24.2 Unlock a Talk Group .....................................................................................................32
7.25 SCANNING ................................................................................................................................32
7.25.1 Checking or Changing Active Scan Mode ....................................................................33
7.25.2 Scanning Priority ...........................................................................................................34
7.26 MAKING SELECTIVE CALLS ................................................................................................34
7.26.1 Manually Dialing a Selective Call (System Model Control Head)................................35
7.26.2 Speed Dialing a Selective Call ......................................................................................35
7.26.3 Receiving a Selective Call.............................................................................................35
7.26.4 Terminating a Selective Call .........................................................................................35
7.27 SELECTIVE ALERT..................................................................................................................36
7.27.1 Sending Selective Alert Messages.................................................................................36
7.27.2 Receiving Messages.......................................................................................................37
7.27.3 Defining Pre-Programmed Messages ............................................................................37
7.28.1 Placing an Interconnect Call..........................................................................................37
7.28.2 Receiving an Interconnect Call......................................................................................38
7.29 EMERGENCY COMMUNICATIONS......................................................................................38
7.29.1 Declaring an Emergency Call or Alert ..........................................................................38
7.29.2 Silent Emergency...........................................................................................................39
7.29.3 Clearing an Emergency Call or Alert ............................................................................39
7.29.4 Receiving an Emergency Call .......................................................................................39
7.29.5 Dismissing an Emergency Call......................................................................................40
7.30 ENCRYPTION ...........................................................................................................................40
7.30.1 Automatic Encryption....................................................................................................40
7.30.2 Manual Encryption (System Model) .............................................................................41
7.31 PRESET BUTTONS...................................................................................................................42
7.32 DYNAMIC REGROUPING.......................................................................................................42
7.33 GPS COORDINATES ................................................................................................................42
8
P25/EDACS/CONVENTIONAL COMMON OPERATION ...........................................................43
8.1
CH721 FRONT PANEL COMPONENTS .................................................................................43
8.1.1 Primary Functions (Quick Access)................................................................................45
TURNING THE RADIO ON......................................................................................................45
SELECTION MODE RULES.....................................................................................................45
8.2
8.3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
TABLE OF CONTENTS
Page
8.4
8.5
DIRECT ACCESS ......................................................................................................................46
FEATURE ENCRYPTION DISPLAY.......................................................................................46
8.5.1 Serial Number ROM (12 Hex Digits)............................................................................47
8.5.2 Feature Encryption Data Stream....................................................................................47
8.5.3 Features Enabled............................................................................................................48
SYSTEM/GROUP/CHANNEL SELECTION............................................................................49
8.6.1 System Selection............................................................................................................49
8.6.2 Group and Channel Selection........................................................................................49
LAST SYSTEM/GROUP/CHANNEL RECALL.......................................................................50
DIGITAL VOICE OPERATION (PROVOICE) ........................................................................50
8.8.1 Voice Modes..................................................................................................................50
8.8.2 Clear Modes...................................................................................................................50
8.8.3 ProVoice Digital Mode..................................................................................................51
8.8.4 ProVoice Private Mode .................................................................................................51
8.8.5 Private Operation...........................................................................................................52
8.8.6 Conventional Operation.................................................................................................53
MACRO KEY OPERATION .....................................................................................................54
8.6
8.7
8.8
8.9
9
EDACS AND P25 TRUNKED OPERATION....................................................................................55
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
RADIO STATUS ICONS...........................................................................................................55
MESSAGES................................................................................................................................56
ALERT TONES..........................................................................................................................58
MENU.........................................................................................................................................59
RECEIVING A CALL................................................................................................................62
SENDING A CALL....................................................................................................................62
CONVENTIONAL FAILSOFT..................................................................................................62
EMERGENCY OPERATION ....................................................................................................63
9.8.1 Receiving an Emergency Call .......................................................................................63
9.8.2 Declaring an Emergency................................................................................................63
SYSTEM SCAN OPERATION..................................................................................................63
9.9.1 Wide Area System Scan ................................................................................................63
9.9.2 ProScan..........................................................................................................................63
9.9.3 Priority System Scan .....................................................................................................64
9.9.4 When Wide Area System Scan Is Enabled....................................................................64
9.9.5 When ProScan Is Enabled .............................................................................................64
9.9.6 Menu Selection..............................................................................................................64
9.9.7 Pre-Programmed Keypad Key.......................................................................................64
9.9
9.10 GROUP SCAN OPERATION....................................................................................................64
9.10.1 Adding Groups to a Scan List........................................................................................65
9.10.2 Deleting Groups from a Scan List .................................................................................65
9.10.3 Nuisance Delete.............................................................................................................66
9.10.4 Turning Scan On............................................................................................................66
9.10.5 Priority Group Scanning................................................................................................66
9.10.6 Turning Scan Off...........................................................................................................66
9.11 INDIVIDUAL CALLS ...............................................................................................................66
9.11.1 Receiving and Responding to an Individual Call ..........................................................66
9.11.2 Call Storage Lists...........................................................................................................67
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
TABLE OF CONTENTS
Page
9.11.3 Sending an Individual Call ............................................................................................68
9.12 SCAT OPERATION...................................................................................................................68
9.13 TELEPHONE INTERCONNECT CALLS.................................................................................68
9.13.1 Receiving a Telephone Interconnect Call (Trunked Mode Only) .................................68
9.13.2 Sending a Telephone Interconnect Call (Trunked Mode Only).....................................69
9.13.3 DTMF Overdial/Conventional Mode Telephone Interconnect......................................69
9.13.4 Programmable Entries ...................................................................................................70
9.14 MOBILE DATA .........................................................................................................................70
9.14.1 Displays .........................................................................................................................71
9.14.2 DATA OFF Operation...................................................................................................71
9.14.3 DATA ON Operation ....................................................................................................71
9.14.4 Exiting Data Calls..........................................................................................................71
9.14.5 Scan Lockout Mode.......................................................................................................71
9.14.6 Data Lockout Mode.......................................................................................................72
9.15 STATUS/MESSAGE OPERATION ..........................................................................................72
9.15.1 Status Operation ............................................................................................................72
9.15.2 Message Operation ........................................................................................................73
9.16 EDACS CONVENTIONAL P1 SCAN ......................................................................................73
9.17 DYNAMIC REGROUP OPERATION.......................................................................................73
9.17.1 Emergency Operation....................................................................................................74
9.18 PAGE (P25 TRUNKED ONLY) ................................................................................................74
10 CONVENTIONAL OPERATION ......................................................................................................75
10.1 RADIO STATUS ICONS ...........................................................................................................75
10.2 MESSAGES................................................................................................................................75
10.3 ALERT TONES..........................................................................................................................77
10.4 MENU.........................................................................................................................................77
10.5 RECEIVING A CALL................................................................................................................79
10.6 SENDING A CALL....................................................................................................................80
10.7 EMERGENCY OPERATION ....................................................................................................80
10.7.1 Using 5-Tone Signaling to Declare an Emergency .......................................................80
10.7.2 Tone Encode Transmission............................................................................................81
10.8 SCANNING CONVENTIONAL CHANNELS .........................................................................81
10.8.1 Adding Channels to a Scan List.....................................................................................81
10.8.2 Deleting Channels From A Scan List ............................................................................82
10.8.3 Nuisance Delete.............................................................................................................82
10.9 TURNING SCAN ON ................................................................................................................82
10.10 TURNING SCAN OFF...............................................................................................................82
10.11 SQUELCH ADJUST...................................................................................................................83
10.11.1 Menu Selection..............................................................................................................83
10.11.2 Pre-Programmed Keypad Key.......................................................................................83
10.12 TYPE 99 DECODE.....................................................................................................................83
10.12.1 Menu Selection..............................................................................................................84
10.12.2 Pre-Programmed Keypad Key.......................................................................................84
10.13 DIRECT MODE OPERATION..................................................................................................84
11 P25 CONVENTIONAL OPERATION...............................................................................................85
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
TABLE OF CONTENTS
Page
11.1 RADIO STATUS ICONS...........................................................................................................85
11.2 MESSAGES................................................................................................................................86
11.3 ALERT TONES..........................................................................................................................87
11.4 MENU.........................................................................................................................................88
11.5 GROUP CALLS IN P25 MODE ................................................................................................90
11.5.1 Transmitting a Group Call.............................................................................................90
11.5.2 Receiving a Group Call .................................................................................................90
11.6 INDIVIDUAL CALLS IN P25 MODE ......................................................................................91
11.6.1 Transmitting an Individual Call.....................................................................................91
11.6.2 Receiving an Individual Call .........................................................................................91
11.7 EMERGENCY GROUP CALLS IN P25 MODE.......................................................................91
11.7.1 Declaring an Emergency Group Call.............................................................................91
11.7.2 Receiving an Emergency Group Call ............................................................................92
12 BASIC TROUBLESHOOTING..........................................................................................................93
13 TECHNICAL ASSISTANCE..............................................................................................................95
14 KEYPAD REMAPPING......................................................................................................................96
15 RADIO SETUP.....................................................................................................................................97
16 WARRANTY ......................................................................................................................................101
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
TABLE OF CONTENTS
FIGURES
Page
Figure 7-1: System Model.......................................................................................................................18
Figure 7-2: Scan Model...........................................................................................................................18
Figure 7-3: Typical Display.....................................................................................................................21
Figure 7-4: Personality Structure Example .............................................................................................23
Figure 8-1: System Model.......................................................................................................................43
Figure 8-2: Scan Model...........................................................................................................................43
Figure 9-1: Typical Display.....................................................................................................................55
Figure 10-1: Typical Display...................................................................................................................75
Figure 11-1: Typical Display...................................................................................................................85
TABLES
Table 2-1: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle
Installations)..........................................................................................................................11
Table 2-2: Rated Power and Recommended Minimum Safe Lateral Distance (Motorcycle
Installations)..........................................................................................................................12
Table 7-1: Front Panel Default Controls and Functions..........................................................................19
Table 7-2: Icons and Descriptions...........................................................................................................22
Table 7-3: M7200 OpenSky Mode Alert Tones......................................................................................24
Table 7-4: Basic Menu Structure.............................................................................................................25
Table 7-5: Keypad Function Commands.................................................................................................27
Table 7-6: Scan Modes............................................................................................................................33
Table 7-7: Status of Selective Alert.........................................................................................................37
Table 8-1: Front Panel Default Controls and Functions..........................................................................44
Table 8-2: Available Feature Numbers ...................................................................................................48
Table 8-3: Transmit/Receive Mode Compatibility for ProVoice Operation ..........................................50
Table 8-4: Current Cryptographic Key Display ......................................................................................52
Table 9-1: Icons and Descriptions...........................................................................................................55
Table 9-2: Display Messages...................................................................................................................56
Table 9-3: Alert Tones.............................................................................................................................58
Table 9-4: Menu Item Information..........................................................................................................60
Table 10-1: Icons and Descriptions.........................................................................................................75
Table 10-2: Display Messages.................................................................................................................75
Table 10-3: M7200 EDACS Mode Alert Tones......................................................................................77
Table 10-4: Menu Item Information........................................................................................................78
Table 11-1: Icons and Descriptions.........................................................................................................85
Table 11-2: Display Messages.................................................................................................................86
Table 11-3: M7200 EDACS Mode Alert Tones......................................................................................87
Table 11-4: Menu Item Information........................................................................................................88
Table 12-1: Basic Troubleshooting .........................................................................................................93
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
1 SAFETY SYMBOL CONVENTION
The following conventions are used throughout this manual to alert the user to general safety precautions
that must be observed during all phases of operation, service, and repair of this product. Failure to comply
with these precautions or with specific warnings elsewhere in this manual violates safety standards of
design, manufacture, and intended use of the product. M/A-COM, Inc. assumes no liability for the
customer’s failure to comply with these standards.
The WARNING symbol calls attention to a procedure, practice, or the like, which,
if not correctly performed or adhered to, could result in personal injury. Do not
proceed beyond a WARNING symbol until the conditions identified are fully
understood or met.
The CAUTION symbol calls attention to an operating procedure, practice, or the like,
which, if not performed correctly or adhered to, could result in a risk of danger, damage
to the equipment, or severely degrade the equipment performance.
CAUTION
The NOTE symbol calls attention to supplemental information, which may improve
system performance or clarify a process or procedure.
The ESD symbol calls attention to procedures, practices, or the like, which could expose
equipment to the effects of Electro-Static Discharge. Proper precautions must be taken
to prevent ESD when handling circuit modules.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
2 RF ENERGY EXPOSURE INFORMATION
2.1 RF ENERGY EXPOSURE AWARENESS, CONTROL INFORMATION,
AND OPERATION INSTRUCTIONS FOR FCC OCCUPATIONAL USE
REQUIREMENTS
Before using your mobile two-way radio, read this important RF energy awareness and control
information and operational instructions to ensure compliance with the FCC’s RF exposure
guidelines.
This radio is intended for use in occupational/controlled conditions, where users have full
knowledge of their exposure and can exercise control over their exposure to meet FCC
limits. This radio device is NOT authorized for general population, consumer, or any
other use.
Changes or modifications not expressly approved by M/A-COM, Inc. could void the
user's authority to operate the equipment.
CAUTION
This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide
communications between two or more users over a distance. It uses RF energy or radio waves to send and
receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited
to, electric power, sunlight, and x-rays. RF energy, however, should not be confused with these other
forms of electromagnetic energy, which, when used improperly, can cause biological damage. Very high
levels of x-rays, for example, can damage tissues and genetic material.
Experts in science, engineering, medicine, health, and industry work with organizations to develop
standards for exposure to RF energy. These standards provide recommended levels of RF exposure for
both workers and the general public. These recommended RF exposure levels include substantial margins
of protection. All two-way radios marketed in North America are designed, manufactured, and tested to
ensure they meet government established RF exposure levels. In addition, manufacturers also recommend
specific operating instructions to users of two-way radios. These instructions are important because they
inform users about RF energy exposure and provide simple procedures on how to control it. Please refer
to the following websites for more information on what RF energy exposure is and how to control your
exposure to assure compliance with established RF exposure limits.
2.1.1 Federal Communications Commission Regulations
Your M/A COM, Inc. M7200 mobile two-way radio is designed and tested to comply with the FCC RF
energy exposure limits for mobile two-way radios before it can be marketed in the United States. When
two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of
and able to control their exposure to meet occupational requirements. Exposure awareness can be
facilitated by the use of a label directing users to specific user awareness information. Your M/A COM,
Inc. M7200 two-way radio has an RF exposure product label. Also, your M7200 Installation and
Operator’s Manuals include information and operating instructions required to control your RF exposure
and to satisfy compliance requirements.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
2.2 COMPLIANCE WITH RF EXPOSURE STANDARDS
Your MA/COM, Inc. M7200 mobile two-way radio is designed and tested to comply with a number of
national and international standards and guidelines (listed below) regarding human exposure to RF
electromagnetic energy. This radio complies with the IEEE and ICNIRP exposure limits for
occupational/controlled RF exposure environment at duty factors of up to 50% talk-50% listen and is
authorized by the FCC for occupational use. In terms of measuring RF energy for compliance with the
FCC exposure guidelines, your radio antenna radiates measurable RF energy only while it is transmitting
(talking), not when it is receiving (listening) or in standby mode.
Your M/A COM, Inc. M7200 mobile two-way radio complies with the following RF energy exposure
standards and guidelines:
•
•
•
United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR §§
2 sub-part J.
American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE)
C95.1-1992.
Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999.
Table 2-1 lists the recommended minimum lateral distance for a controlled environment
and for unaware bystanders in an uncontrolled environment, from transmitting types of
antennas (i.e., monopoles over a ground plane, or dipoles) at rated radio power for
mobile radios installed in a vehicle. Transmit only when unaware bystanders are at least
the uncontrolled recommended minimum lateral distance away from the transmitting
antenna.
CAUTION
2.2.1 Mobile Antennas (Vehicle Installations)
Table 2-1: Rated Power and Recommended Minimum Safe Lateral Distance (Vehicle Installations)
RATED POWER
OF MOBILE
TWO-WAY
RADIO
RECOMMENDED SAFE MINIMUM LATERAL
DISTANCE FROM TRANSMITTING ANTENNA
MOBILE RADIO
FREQUENCY SPLIT
ANTENNA P/N
CONTROLLED
32 cm
UNCONTROLLED
70 cm
AN102800V1
AN102800V2
32 cm
70 cm
AN-025167-001
AN-025167-002
AN-025167-004
AN-025167-005
AN-025167-006
AN-025167-010
AN-025167-011
AN-025167-014
AN-025167-015
32 cm
70 cm
32 cm
70 cm
32 cm
70 cm
760 -870 MHz
15W
32 cm
70 cm
32 cm
70 cm
32 cm
70 cm
32 cm
70 cm
20 cm
67 cm
20 cm
67 cm
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
Install the radio’s antenna (refer to Table 2-1 for applicable antenna part numbers) in the center of the
vehicle’s roof. These mobile antenna installation guidelines are limited to metal body motor vehicles or
vehicles with appropriate ground planes. The antenna installation should additionally be in accordance
with the following:
•
•
•
The requirements of the antenna manufacturer/supplier included with the antenna.
Instructions in the M7200 Radio Installation Manual, including minimum antenna cable lengths.
The installation manual providing specific information of how to install the antennas to facilitate
recommended operating distances to all potentially exposed persons.
Use only the M/A-COM approved/supplied antenna(s) or approved replacement antenna. Unauthorized
antennas, modifications, or attachments could damage the radio and may violate FCC regulations.
2.2.2 Mobile Antennas (Motorcycle Installations)
This device must not be co-located or operating in conjunction with any other antenna or
transmitter.
Table 2-2: Rated Power and Recommended Minimum Safe Lateral Distance
(Motorcycle Installations)
MOBILE
RADIO
FREQUENCY
SPLIT
RECOMMENDED SAFE MINIMUM LATERAL
DISTANCE FROM TRANSMITTING ANTENNA
RATED POWER OF
MOBILE TWO-WAY
RADIO
ANTENNA P/N
CONTROLLED
UNCONTROLLED
806-870 MHz LE-OM806HDBKTNCDS
15W
15 cm
41 cm
recommended antennas) on the end of the motorcycle case farthest away from the driver. These mobile
antenna installation guidelines are limited to motorcycles fit with the motorcycle radio case with integral
antenna grounding plane. The antenna installation should additionally be in accordance with the
following.
•
•
The requirements of the antenna manufacturer/supplier included with the antenna.
Instructions in the M7200 Radio and Control Unit Motorcycle Installation Manual, including
minimum antenna cable lengths.
•
The installation manual providing specific information of how to install the antennas to facilitate
recommended operating distances to all potentially exposed persons.
Use only the M/A-COM approved/supplied antenna(s) or approved replacement antenna(s).
Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC
regulations.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
2.2.3 Approved Accessories
This radio has been tested and meets the FCC RF guidelines when used with the M/A-COM accessories
supplied or designated for use with this product. Use of other accessories may not ensure compliance with
the FCC’s RF exposure guidelines, and may violate FCC regulations.
For a list of M/A-COM approved accessories refer to the product manuals, M/A-COM’s Products and
Services Catalog, or contact M/A-COM at 1-800-368-3277.
2.2.4 Contact Information
For additional information on exposure requirements or other information, contact M/A-COM, Inc. at 1-
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
3 OPERATION SAFETY RECOMMENDATIONS
3.1 TRANSMITTER HAZARDS
The operator of any mobile radio should be aware of certain hazards common to
the operation of vehicular radio transmitters. A list of several possible hazards is
given:
•
•
Explosive Atmospheres – Just as it is dangerous to fuel a vehicle with the motor running, similar
hazards exist when operating a mobile radio. Be sure to turn the radio off while fueling a vehicle. Do
not carry containers of fuel in the trunk of a vehicle if the radio is mounted in the trunk.
Areas with potentially explosive atmosphere are often, but not always, clearly marked. Turn OFF
your radio when in any area with a potentially explosive atmosphere. It is rare, but not impossible that
the radio or its accessories could generate sparks.
Interference to Vehicular Electronics Systems – Electronic fuel injection systems, electronic anti-
skid braking systems, electronic cruise control systems, etc., are typical electronic systems that can
malfunction due to the lack of protection from radio frequency energy present when transmitting. If
the vehicle contains such equipment, consult the dealer and enlist their aid in determining the
expected performance of electronic circuits when the radio is transmitting.
•
•
Electric Blasting Caps – To prevent accidental detonation of electric blasting caps, DO NOT use
two-way radios within 1000 feet of blasting operations. Always obey the “Turn off Two-Way
Radios” signs posted where electric blasting caps are being used. (OSHA Standard: 1926-900)
Liquefied Petroleum (LP) Gas Powered Vehicles – Mobile radio installations in vehicles powered
by liquefied petroleum gas with the LP gas container in the trunk or other sealed-off space within the
interior of the vehicle must conform to the National Fire Protection Association standard NFPA 58
requiring:
¾ The LP gas container and its fittings.
¾ Outside filling connections shall be used for the LP gas container.
¾ The LP gas container shall be vented to the outside of the vehicle.
3.2 SAFE DRIVING RECOMMENDATIONS
(Recommended by AAA)
•
•
Read the literature on the safe operation of the radio.
Keep both hands on the steering wheel and the microphone in its hanger whenever the vehicle is in
motion.
•
•
Place calls only when the vehicle is stopped.
When talking from a moving vehicle is unavoidable, drive in the slower lane. Keep conversations
brief.
•
•
If a conversation requires taking notes or complex thought, stop the vehicle in a safe place and
continue the call.
Whenever using a mobile radio, exercise caution.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
4 OPERATING RULES AND REGULATIONS
Two-way FM radio systems must be operated in accordance with the rules and regulations of the local,
regional, or national government.
In the United States, the M7200 mobile radio must be operated in accordance with the rules and
regulations of the Federal Communications Commission (FCC). As an operator of two-way radio
equipment, you must be thoroughly familiar with the rules that apply to your particular type of radio
operation. Following these rules helps eliminate confusion, assures the most efficient use of the existing
radio channels, and results in a smoothly functioning radio network.
When using your two-way radio, remember these rules:
•
It is a violation of FCC rules to interrupt any distress or emergency message. As your radio operates
in much the same way as a telephone “party line,” always listen to make sure that the channel is clear
before transmitting. Emergency calls have priority over all other messages. If someone is sending an
emergency message – such as reporting a fire or asking for help in an accident – KEEP OFF THE
AIR!
•
•
The use of profane or obscene language is prohibited by Federal law.
It is against the law to send false call letters or false distress or emergency messages. The FCC
requires that you keep conversations brief and confine them to business. To save time, use coded
messages whenever possible.
•
•
•
•
Using your radio to send personal messages (except in an emergency) is a violation of FCC rules.
You may send only those messages that are essential for the operation of your business.
It is against Federal law to repeat or otherwise make known anything you overhear on your radio.
Conversations between others sharing your channel must be regarded as confidential.
The FCC requires that you identify yourself at certain specific times by means of your call letters.
Refer to the rules that apply to your particular type of operation for the proper procedure.
No changes or adjustments shall be made to the equipment except by an authorized or certified
electronics technician.
Under U.S. law, operation of an unlicensed radio transmitter within the jurisdiction of
the United States may be punishable by a fine of up to $10,000, imprisonment for up to
two (2) years, or both.
4.1 OPERATING TIPS
The following conditions tend to reduce the effective range of two-way radios and should be avoided
whenever possible:
•
•
•
Operating the radio in areas of low terrain, or while under power lines or bridges.
Obstructions such as mountains and buildings.
In areas where transmission or reception is poor, some improvement can be obtained by moving a few
yards in another direction or moving to a higher elevation.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
5 PRODUCT DESCRIPTION
The M7200 mobile is a state-of-the-art radio that operates seamlessly between the 800 MHz frequency
band and the 700 MHz frequency band. The M7200 is designed to meet the critical communications
demands of public service users and complies with MIL-STD-810F specifications.
The M7200 is capable of supporting multiple operating modes, including OpenSky® digital operation,
EDACS® or ProVoiceTM trunked modes, P25 digital trunked mode, P25 digital conventional mode, and
conventional analog mode.
The M7200 uses Time Division Multiple Access (TDMA) technology in the OpenSky mode to allow
multiple users to share a single RF channel. In addition, a single RF channel can support simultaneous
digital voice and data communications.
The M7200 provides integrated voice and data services. Voice operation is provided using a microphone
and speaker included in the radio installation kit. For data transfers, the M7200 is constructed with an
industry-standard RS-232 interface serial port for connecting an optional laptop PC.
A PC, not included with the M7200, provides network connectivity through the standard serial
(DCE-type) interface.
The M7200 has an integrated Global Positioning System (GPS) receiver. This allows the M7200 to fully
support the Automatic Vehicular Locator (AVL) for fleet management and dispatch applications.
The OpenSky M7200 benefits from a flexible, software-based digital radio design. Features and user
profiles are software-defined and can be reprogrammed over the air. The optional over-the-air
programming feature allows communication protocols to be changed easily and added at any time.
5.1 REMOTE CONTROL HEAD OPERATION
For remote mount installations configured with a CH721 control head, all normal radio operations and
interfaces can be handled via the control head connected to the radio unit by a single twisted-pair
connection routed through a vehicle. Up to six control units may be attached to a trunk mount radio. Each
control head provides a serial access point for data and any one (only one at a time) can be connected to a
data device such as a personal computer.
Where multiple control heads are connected or where a dash-mount radio is installed with additional
remote control heads, the following features are available from each position:
•
Outgoing voice calls can be initiated. Any control head can initiate a call but only one can talk at a
time. All other connected control heads will hear both sides of the conversation.
•
•
•
Incoming and outgoing audio can be heard. Outgoing audio is not broadcast at the source position.
Independent audio control is available.
Radio settings such as talk group, scan mode etc., can be controlled. Any connected control head can
override the radio settings of other connected control heads.
•
•
Comfort settings, such as volume and display brightness that are applicable to the individual control
head can be adjusted and cannot be overridden by other control heads.
An optional intercom function is available between control units. Audio will be broadcast to ALL
connected control heads.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
6 CHANGE OPERATING MODE
6.1 CHANGE FROM OTP MODE
To change from OTP operating mode to P25, EDACS, or Conventional:
1. Use
display.
to cycle through the menu until the “Mode Menu” appears in the bottom line of the
2. Use
to choose an available mode. Press MENU and confirm (Y/N) with
and press
MENU again.
3. Press the MENU button to confirm.
6.2 CHANGE TO OTP MODE
1. Use
to scroll through available systems until OpenSky is displayed.
2. The radio transitions to OTP mode.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7 OPENSKY OPERATION
7.1 CH721 FRONT PANEL COMPONENTS
The front panel of the control head includes a dot matrix display, controls for menu navigation, an
emergency button, three pre-set buttons, a Power On-Off/Volume Control knob, and a microphone
connector. In addition, the system model control head features a DTMF keypad. Table 7-1 lists all default
front panel controls and their functions.
Figure 7-1: System Model
Figure 7-2: Scan Model
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
The buttons on the front panel are backlit for operation in a low ambient light level such as nighttime
operation. Some buttons also flash to provide feedback of various operating conditions.
In addition, the front panel contains a light-level sensor that samples ambient light levels for automatic
display and button backlight brightness adjustments. In other words, it automatically brightens the display
and backlights when higher external light levels exist and it automatically dims the display and backlights
during lower external light levels.
Table 7-1: Front Panel Default Controls and Functions
PART
FUNCTION
Power On-
Off/Volume Control
Knob
Turn knob clockwise to power on the radio and increase volume.
Turn counter-clockwise to decrease volume and power off the radio.
Mic Connection
Connection for hand-held, hands-free, speaker-mic, or headset.
If enabled through programming, the emergency button sends an emergency alert and opens
voice communication on the currently selected talk group or the default emergency talk group
(depending upon how the system is defined).
Ambient Light
Sensor
Radio automatically adjusts the display and button backlight brightness level based on
ambient light. Do not block this sensor.
While in the dwell display, scrolls through available talk groups.
Scrolls through selections within the active menu (available talk groups, pre-programmed
speed dial numbers, canned alert messages, etc.).
or
Scrolls through available menu items.
OPT/OPTION
CLR/CLEAR
Press to activate the current selection. In some cases, this is not necessary as the last
selection will automatically activate after a short period.
MENU
Menu selections and messages.
Network Connectivity icon.
Display Area
Current Volume Level icon.
Volume represented numerically within the display (0 = Muted, 40 = Loudest).
User may select which one of several dwell displays the radio uses.
These buttons are used to store and recall user-selectable parameters such as scan mode,
selected profile, selected talk group, and priority talk group. Different parameters can be
stored at each of the three different pre-set buttons.
Pre-Set Buttons
Preset button C can be configured via programming to reboot the radio into a particular
application mode. Contact your system administrator to determine if this feature is enabled in
your radio.
A, B, & C
SCAN
Not functional in OpenSky systems.
7.2 POWER UP AND VOLUME CONTROL
7.2.1 Power Up
1. Rotate the Power On-Off/Volume Control knob clockwise to power on the radio. The display will
illuminate when the radio powers up.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
2. Wait for the power-up sequence to complete, which takes approximately ten (10) seconds.
During this time, if enabled for auto registration, the radio is provisioned with a customized user
personality designed for the user’s specific needs by the OpenSky network administrator.
If this personality contains encrypted talk groups or if the user is authorized for, and intends to use,
manual encryption, User Login must be performed. This requires a system model control head so that
the User ID and password can be entered.
3. When provisioning is complete, the radio will display the Dwell Display.
If User Login is required, the bottom line of the Dwell Display will flash the message “Pls Login.”
7.2.2 Volume Control
Turn the Power On-Off/Volume Control knob clockwise to increase the volume and counter-clockwise to
decrease the volume.
7.3 SELF-TEST
After power-up, the M7200 radio undergoes a multi-function automatic registration procedure. As many
as sixteen (16) possible radio profiles are downloaded to the radio from the network in response to the
User’s ID.
7.4 LOGIN TO THE NETWORK
Login occurs either automatically (auto registration) if the radio has a valid registration or, if enabled and
If encryption is enabled and authorized on the radio, the user will be prompted to “Pls Login” with the *1
login command, a User ID, and password [System Model Control Head required].
1. Press *1 (Login command).
2. Enter the full 10-digit User ID.
3. Press the # key.
4. Enter the password.
•
•
If the radio is configured for alpha-numeric passwords and the password has consecutive
duplicate numbers (“MES33” for example), enter # between the consecutive duplicate numbers
so the radio will not interpret the entry as a letter (“D” in this example).
If the radio is configured for numeric-only passwords, do not enter # between duplicated
numbers.
5. Press the # key twice.
regarding log off commands.) The password will be established before the radio is put into operation.
Contact the local OpenSky network administrator for more information.
If necessary, contact radio system administration personnel for login assistance and/or
radio-specific login instructions.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7.5 LOG OFF THE NETWORK
The *0## command de-registers the radio. Typically, this is automatically performed when powering
down the radio. Using this method, the User ID is remembered by the radio so only the password is
needed at next login. Manually log off by pressing *0## (requires System Model).
If a user is logged in using encryption features, it is necessary to log off when encryption is no longer
required.
7.6 TURNING THE RADIO OFF
To turn the radio off, rotate the Power On-Off/Volume Control knob counter-clockwise. In multiple
control head installations, turning off the last powered-up control head also automatically turns off the
radio.
Several user-selected radio settings (i.e., scan mode, pre-set buttons, and side tone levels) are maintained
for the next operational session. At the next radio power-up, maintained settings will automatically
restore, along with the network personality settings. In multiple control head installations, settings are
maintained for each control head position.
If power is abruptly disconnected from the radio prior to executing the correct turn-off
procedure, user-selected radio settings and last-tuned channel information will be lost.
This can extend the time required for the radio to register with the network upon the
subsequent power-up.
7.7 MENU DISPLAY AND CONTROL AREA
Following power-up, the radio display shows the default talk group (Figure 7-3). Pressing up or down
with
changes the display to the next available menu. In many cases, the dwell display
automatically re-appears after no menu buttons are pressed for a short period of time (between 10 and 30
seconds). For some menus such as the GPS and User ID menus, this does not occur until the user presses
a front panel button.
When the dwell display is active, it will change dynamically to reflect the current profile, received talk
group/caller ID (when available), or channel (when enabled).
The radio’s display is highly interactive. It responds in the top and bottom text lines as the user presses
the menu buttons (
,
and MENU) to scroll through the menu loop and the entries for each
Figure 7-3: Typical Display
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7.8 RADIO STATUS ICONS
Status Icons indicate the various operating characteristics of the radio. The icons show operating modes
and conditions (see Table 7-2). The location of icons on the display may vary depending on configuration.
Table 7-2: Icons and Descriptions
ICON
DESCRIPTION
Indicates data registration.
Volume bars – indicates relative volume level.
7.9 DWELL DISPLAY
When not engaged in menu selection, the first two lines of the display default to the user-defined display,
known as the “dwell display.” The top line indicates the currently selected talk group. The second line
will display the currently selected profile, caller ID/alias1, received talk group, and current channel name.
Press the
ramp control to scroll through and view one of these second line options.
7.10 PERSONALITY
As illustrated in Figure 7-4, a personality defines the profiles and talk groups available to the user. It is
the structuring of a collection of profiles and privileges established by the OpenSky network administrator
to provide the user with a comprehensive set of profiles to communicate effectively with the necessary
talk groups or individuals.
Personalities are stored on the network and downloaded over-the-air to the radio. This process is called
“provisioning.” Provisioning occurs at radio power-up and at user log-in. Each personality can contain up
to sixteen (16) profiles and each profile can contain up to sixteen talk groups.
7.10.1 Profiles
As stated above, each profile can contain up to sixteen (16) talk groups. A profile also defines the radio’s
emergency behavior. All transmissions are made on the selected talk group (displayed on the top line of
the dwell display). The user can change the selected talk group to any of the other talk groups within the
profile.
1 Alias is a logical ID name such as “J_Smith.” The name corresponds to a user ID such as 003-542-0001.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
Profile 1
Profile 2
Profile 3
TG a
TG d
TG g
TG a
TG b
TG c
TG x
TG y
TG z
TG d
TG e
TG f
TG h
TG i
TG = Talk Group
Figure 7-4: Personality Structure Example
If Global Profile is enabled by the system administrator, the number of available talk
groups to scan doubles.
7.10.2 Talk Groups
A talk group represents a set of users that regularly need to communicate with one another. There can be
any number of authorized users assigned to a talk group. Talk groups are established and organized by the
OpenSky network administrator. An OpenSky talk group is similar to a channel within a conventional FM
radio system.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7.11 ALERT TONES
The M7200 radio also provides audible Alert Tones or “beeps” to indicate the various operating
conditions (see Table 7-3).
Table 7-3: M7200 OpenSky Mode Alert Tones
NAME
TONE
DESCRIPTION
one low tone/two high
tones
Call Queued
Call queued for processing.
Radio is out of coverage area or requested talk group
is active.
Call Denied
three short beeps
Sounds when resources become available for a call
request placed in the queue (if enabled) upon channel
access.
If the radio roams to another site while transmitting,
then it will auto rekey and begin transmitting on that
tower. It gives a second grant tone to let the user
know they have roamed.
Grant (or Go-
Ahead)
single short beep
Notifies the user access to the channel has been lost
(out of coverage area or pre-empted by higher-priority
call)
single long low-pitched
tone
Call Removed
Selective Alert
Received
Only played once to indicate a selective alert has
been received.
four short tones
Emergency Alert
Tone
three long tones
Sounds when an emergency alert is declared
Sounds when an emergency is cleared
Emergency
Cleared Tone
one long low-pitched tone
Ringing is repeated every four seconds until the call is
accepted or rejected by the radio being called or until
the network drops the call if unanswered after one
minute
Selective Call Ring
Tone
a ringing tone similar to a
telephone
Two ring tone - one generated by the radio when
there is an incoming telephone call or an outgoing
telephone call attempt is waiting for the telephone
interconnect gateway equipment to dial the Public
Switched Telephone Network (PSTN). The second
ring tone sounds when the gateway equipment has
dialed the number.
a single medium-pitch
repeating tone
PSTN Ring Tones
Two short tones, one
high-pitched and one
low-pitched
Sounds when the radio transitions from one radio
base station site to another.
Roam Tone
If enabled via programming, sounds at
a
Out of Range Tone
three brief tones
programmable interval while the radio is in a state of
persistent deactivation.
7.12 BASIC MENU STRUCTURE
Table 7-4 illustrates the basic M7200 OpenSky menu structure. Menu items will vary depending upon
system programming, radio hardware, and optional configurations. All menus except the dwell display
menu can be turned off by network administration personnel.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
Table 7-4: Basic Menu Structure
Radio Displays
(top and bottom lines)
Menu Name
Usage Notes
To/From Dwell Display
registration, RF sync and
transceiver status codes
bit-error rates
Engineering Display
(Menu may not be
available per radio
programming.)
Displays radio system connection data. For engineering use.
and RSSI data
OFF/ON
“SilentEmerg”
Silent Emergency
Use
Use
to toggle Silent Emergency OFF/ON.
available modes
to choose an available mode. Press MENU and
Operating Mode
(e.g., OTP, EDACS, etc.)
“Mode Menu”
confirm (Y/N) with
and press MENU again.
current latitude and
longitude
Radio’s current GPS latitude and longitude position scrolls
across top line of the display. Applies to GPS-equipped radios
only.
GPS Fix
User ID
“GPS Fix”
User ID # of user
currently logged in
“User ID”
User’s identification/name scrolls across top line of the display
(if programmed).
Radio’s IP address
Radio’s Internet Protocol (IP) address scrolls across top line of
the display.
IP Address
Station Identification
Stealth Mode
“IP Address”
station’s call sign
Station’s identification/name scrolls across top line of the display
(if programmed).
“Station ID”
“OFF”
“StealthMenu”
Use
to enable. Press any button to disable.
“LOW”, “MEDIUM”,
“MEDHIGH”, “HIGH”
“Treble Menu”
Use
to choose speaker/headset treble level. Press
Treble Level
Display Brightness
Side Tone Level
Intercom
Select to return to dwell display.
“<< >>”
“Bright Menu”
Use
display.
to dim or brighten. Press MENU to return to dwell
“OFF”, “LOW”, “MED”,
“HIGH”
Use
dwell display.
to choose side tone level. Press MENU to return to
“Side Menu”
“ON” or “OFF”
“INTERCOM”
Use
dwell display.
to turn intercom on and off. Press MENU to return to
Selected Channel
(Menu may not be
available per radio
programming)
selected channel
Displays the current channel. Press MENU to return to dwell
display.
“ChannelMenu”
See Next Page
25
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
Radio Displays
(top and bottom lines)
See Previous Page
Menu Name
Usage Notes
current scan mode
“ScnModeMenu”
Use
dwell display.
to turn Scan on and off. Press MENU to return to
Scan Mode
talk group “<”
“LockOutMenu”
Talk group
Lock Out
Use
to choose a talk group for locking/unlocking. Press
MENU to toggle “<” on (locked out) and off.
current priority talk group
Priority 1
Talk group
Use
to choose new priority talk group. Press MENU to
“Priority2”
return to dwell display.
current priority talk group
Priority 2
Talk group
Use
to choose new priority talk group. Press MENU to
“Priority1”
return to dwell display.
alert received
“EmgDismiss”
Use
dismiss.
to choose emergency talk group. Press MENU to
Emergency Dismiss
Alerts Received
time/sender’s name/
alias/message text
“AlertsRcvd”
“No alerts” or alert message text scrolls in display. Use
to view messages.
or oldest message
current speed dial #
Use
to choose a speed-dial number. Press MENU to go
to “AlertMsg” menu. Scroll through canned messages with
Alert Destination
“AlertDest”
. Press MENU to send message and return to dwell
display.
current speed dial #
Use
use
to choose a speed-dial number. Press MENU, then
Speed Dial
“SpeedDial”
to select canned message.
currently active profile
Use
to choose an available profile. Press MENU to
Profile Selection
“ProfileMenu”
return to dwell display.
selected talk group
“TalkGrpMenu”
Talk group
Selection
Use
to choose a talk group in current profile. Press
MENU to return to dwell display.
Selected talk group
(bottom line option)
Use
to scroll top line through talk groups. Press MENU
Dwell Display
to change bottom line option.
Use
, CLR, or OPT to scroll through menus.
Menus will vary depending upon system programming, radio hardware, and optional
configurations.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7.13 DUAL-TONE MULTI-FREQUENCY
Dual-Tone Multi-Frequency (DTMF) is the system used by touch-tone telephones. DTMF assigns a
specific tone frequency to each key so a microprocessor can easily identify its activation. The radio
entering a user ID and password, or selective calling.
When a key on the DTMF keypad is pressed, the DTMF tone is played through the radio’s speaker.
7.14 KEYPAD COMMANDS (SYSTEM MODEL CONTROL HEAD)
To perform a command from the keypad, press the * key followed by one of the pre-set function keys as
follows:
Table 7-5: Keypad Function Commands
additional information.
*1
Enter Scene of Incident Mode (SOI) on specified channel: *4<LC>#<Band># where LC is the
channel number that is being used as a SOI repeater and band is the number assigned to each
frequency band. For example, if LC 25 800 MHz (band 0) is being used for SOI, then enter
*4
*4,25,#,0,#.
*4#
*6
Exit SOI Mode with.
Go to default profile: Selects default profile if the radio is not voice registered.
additional information.
*7
*8 Radio-to-Radio Call command: Selective call number # (PTT to dial).
information.
*9
Begin Manual Encryption command: *32<Pre-Determined Encryption Key >#
*32
1 – 16 digit encryption key for 128 bit encryption; 17 – 32 digit encryption key for 256 bit
*33 End Manual Encryption command.
7.14.1 Password Entry
Password entry requires a system model control head. Password characters are encrypted on the display
using symbols to indicate the entry. The encryption symbols for each entry will appear in the display as
they are scrolled through, for example: '-' and '+'. Press the # key twice to complete the entry process.
If the password is wrong, the radio will not successfully register with the network for
wide area voice reception. The radio can still be used in single-site mode.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7.14.2 DTMF Overdial
Using the keypad on a System Model, the radio can transmit DTMF tones corresponding to
numbers/characters 0 — 9, * and # on the keypad. To overdial numbers/characters, transmit by pressing
and holding the PTT button and then, press the corresponding keys (one at a time) on the keypad.
7.15 CHANGING THE ACTIVE PROFILE
The radio can store up to sixteen (16) standard profiles, one of which is the currently active profile. To
change the currently active profile:
1. Scroll through the menu with
2. Use to scroll through the list of available profiles.
3. Profile becomes active when selected for longer than two (2) seconds, when the MENU is pressed, or
when the menu is changed using
until “ProfileMenu” is displayed.
.
7.16 CHECKING OR CHANGING THE SELECTED TALK GROUP
Each profile stored in the radio can have up to sixteen (16) talk groups. One talk group within the
currently active profile is set as the “selected talk group.” For the radio user, the selected talk group is
typically the focus of most voice transmissions and receptions. There are two ways to change the selected
talk group:
First Method:
1. Use
to scroll through the menu until “TalkGrpMenu” appears on the bottom line of the
display. The currently selected talk group appears in the top line of the display.
2. Use to scroll through the available list of talk groups in the active profile. This list is
determined by the OpenSky network administrator.
Second Method:
From the dwell display, use the talk group selection knob or
talk groups in the active profile.
to scroll through the available list of
7.17 ADJUSTING DISPLAY AND BUTTON BACKLIGHT BRIGHTNESS
The radio uses a light sensor on the front panel to automatically adjust display brightness and button
backlight brightness to ambient light conditions. The display and backlights automatically brighten at
higher external light levels and automatically dim at lower external light levels. However, the “Bright
Menu” gives the user some manual brightness control as follows:
1. Using
2. Use
, scroll through the menu until “Bright Menu” appears.
to increase or decrease brightness. Display and button backlight brightness will
immediately dim or brighten.
7.18 STEALTH MODE
For some users, it is important to be able to turn off the radio’s display lights, button backlighting, volume
and side tones, but not the radio traffic. For example, in covert operations, lights and sounds could
inadvertently expose an otherwise unobservable radio user. For this purpose, the radio has a Stealth
feature that disables the radio display light, indicator light, and audible side tones.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
When stealth mode is on, the radio continues to scan the programmed list of talk groups and the user can
key-up on the selected talk group.
7.18.1 Enabling Stealth Mode
1. Using
, scroll through the menu until “StealthMenu” appears.
2. To immediately turn Stealth Mode on, press (+) or (-) with
.
3. To turn Stealth Mode off, press any button on the radio’s front panel.
7.18.2 Disabling Stealth Mode
Pressing any radio button other than the mic’s PTT button or the emergency button on front panel will
immediately turn Stealth Mode off. For example, pressing the MENU button on the front panel will turn
Stealth Mode off.
With stealth mode on, pressing any radio button (other than the mic’s PTT button
or the emergency button) on front panel will immediately turn stealth mode off.
7.19 ADJUSTING SIDE TONE AUDIO LEVEL
The radio sounds confirming tones called “side tones” when its buttons are pressed. Most users find this
audible confirmation helpful when navigating the menus. Side tone audio level can be adjusted or turned
completely off using the “Side Menu.”
For covert operations, it may be necessary to turn off side tones. For safety’s sake, turning off the radio
during covert operations is not recommended.
To temporarily disable the side tones that could expose the user’s presence and position, use the menu
buttons to access the “Side Menu” and select “Off” from the menu choices.
If the radio is operating properly but side tones are not heard when the menu buttons are pressed, the side
tones are probably turned off. To turn them back on, access the “Side Tone” menu and select a setting
other than “off.”
Use the following procedure set side tone level:
1. Use
display.
to cycle through the menu until the “Side Menu” appears in the bottom line of the
2. Use
to change to the desired level (Off, Low, Medium, and High). To turn side tones
completely off, use the “Off” setting.
7.20 CHANGE OPERATING MODE
1. Use
display.
to cycle through the menu until the “Mode Menu” appears in the bottom line of the
2. Use
to choose an available mode. Press MENU and confirm (Y/N) with
and press
MENU again.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7.21 RECEIVING AND TRANSMITTING VOICE CALLS
As soon as the radio completes the startup/login/provision/self-test sequence and registers on the
OpenSky network, voice calls from talk groups in the active profile will be audible.
7.21.1 Receiving a Voice Call
No action is required to receive a voice call. The display responds to incoming voice calls as follows:
•
When the dwell display is set to received talk group and the scan mode is Normal or Fixed:
a. If the received talk group matches the selected talk group, then the alias (if available) or user ID
of the incoming caller is displayed.
b. If the received talk group does not match the selected talk group, then the received talk group
name is displayed
•
•
When the dwell display is set to received talk group and the scan mode is None:
a. If the received talk group matches the selected talk group, then the alias (if available) or the user
ID of the incoming caller is displayed.
b. If the received talk group does not match the selected talk group, then None is displayed.
When the dwell display is not set to received talk group, then there is no display indication of an
incoming call.
Refer to Section 7.25 for detailed information on talk group scanning. Refer to Section 7.30 for detailed
information regarding sending and receiving encrypted calls.
7.21.2 Transmitting a Voice Call
Transmit a voice call as follows:
1. Turn the radio on.
3. Select the desired talk group for transmitting on.
4. Press and hold the Push-to-Talk (PTT) button on the hand-held microphone, pause for a moment,
and then speak normally. For maximum clarity, hold the microphone approximately 1 ½ inches from
the mouth and do not shout or whisper into it. If the call is queued by the network, wait for the grant
tone to sound before speaking.
5. Release the PTT button when finished speaking.
7.22 ADJUSTING AUDIO TREBLE LEVEL
The tone of received signals can be adjusted using the radio’s “Treble Menu” as follows:
1. Use
to scroll through the menu until “Treble Menu” appears. The radio’s current treble level
setting indicates in the top line of the display. There are four levels available: low, medium, medium-
high, and high.
2. Use
to increase or decrease.
3. Press the MENU button or wait a few seconds to return to the Dwell Display.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7.23 INTERCOM MODE
The optional intercom mode gives users at multiple control heads connected to the same radio the ability
to communicate with each other without transmitting over-the-air. Turn intercom mode on and off using
the “INTERCOM” menu as follows:
1. Use
2. Use
to cycle through the available menu items until “INTERCOM” appears in the display.
to toggle between “On” and “Off.”
When intercom mode is turned on:
•
•
•
Incoming voice calls will override intercom communications for the duration of the voice call. The
radio and associated control heads will remain in intercom mode and intercom communications will
resume when the voice call ends.
“TG: INTERCOM” appears in the control head’s display when talking on the intercom. This indicates
microphone audio is not sent out on the selected talk group; rather, it remains localized between the
radio control positions (i.e., the control heads connected to the mobile radio).
If a call exists on the currently selected talk group when a PTT button is pressed at one of the control
heads, “TG: in use” appears in the display to indicate intercom mic audio cannot preempt the call on
the talk group.
A user at a radio with only one control head/front panel can turn intercom mode on. In
this case, pressing the microphone’s PTT button will NOT send microphone audio
anywhere.
CAUTION
7.24 TALK GROUP LOCK OUT
There are two ways of focusing voice communications by suppressing calls from talk groups in the
currently active profile:
1. No Scan. By turning scan off (selecting “No Scan” via the “ScnModeMenu”), only the selected talk
group is audible.
2. Lock Out. By locking out selected talk groups, the “chatter” of the locked out talk groups cannot be
heard. This focuses the user’s scanning resources to calls only on desired talk groups.
Talk group lock out is a scan-related feature. With lock out, one or more talk groups in the active profile
can be temporarily disabled from being scanned. Calls are not received on locked-out talk groups. Lock
out settings are not retained between profile changes or when the radio is power cycled.
Lock out is a listening (receive) function and only blocks received calls on locked out
talk groups. Lock out does not affect transmit capability. The above methods do not
apply to recent emergency lock outs.
Only talk groups in the active profile can be locked out, since they are the only talk groups whose voice
calls can be heard on the radio.
P1 and P2 talk groups cannot be locked out.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
The default emergency and emergency-capable talk groups can be locked out if they are NOT in an
emergency state. If a talk group is locked out and is subsequently changed to the currently selected talk
group, it will automatically be unlocked by the radio so the user can hear calls on the talk group. The
radio may be configured so all talk groups are automatically locked out by default. In this case, they must
be manually unlocked, if desired.
7.24.1 Lock Out a Talk Group
1. Use
to scroll through the menu until “LockOutMenu” appears in the bottom line of the
display. The name of a talk group in the currently active profile will appear in the top line.
2. Use to scroll through the list of talk groups, if any, until the desired talk group for lock out
appears in the top line of the display.
3. Press the MENU button to lockout the displayed talk group. A less than symbol (<) appears next to
the talk group’s name.
4. Repeat steps 2 and 3, as needed, to lockout additional talk groups.
The dwell display will re-appear a few seconds after button presses end.
While scrolling through talk groups in the active profile, the only talk groups that appear in the
“LockOutMenu” are those in the active profile.
7.24.2 Unlock a Talk Group
1. Use
to scroll through the menu until “LockOutMenu” appears in the bottom line of the
display. The name of a talk group in the currently active profile will appear in the top line.
2. Use
to scroll through the list of talk groups, if any, until the talk group desired for unlocking
appears in the top line of the display. A less-than symbol (“<”) appears next to the name of a talk
group that is currently locked out.
3. Press the MENU button to unlock the talk group. The less-than symbol (“<”) next to the name of the
talk group disappears. The dwell display appears as soon as the radio acknowledges the selection.
•
•
Changing the active profile removes any lockouts you have made.
Turning off the radio removes any lockouts you have made.
7.25 SCANNING
Three scanning modes are available for the radio, but only one can be active at any time. Changing the
scanning mode changes the way the radio scans voice calls for all of profiles in the radio personality, no
matter which profile is or becomes active.
As described in Table 7-6, the choice of scanning mode changes the span of communications with all the
talk groups in the radio’s profiles, but does not affect interaction with the talk groups.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
Table 7-6: Scan Modes
EXPLANATION
SCAN
MODE
Eliminates distractions.
Full communications (transmit and receive) on selected talk group.
No calls received from other talk groups.
No Scan
The user can scan all talk groups in the active profile that are not locked out as long as
there is demand on the site.
Priority (P1 and P2) groups are user selectable.
Receive calls from more than one talk group, if available from the current site.
Normal
Allows dragging of the selected talk group, P1, P2, and default emergency talk groups to
the site on which the radio is registered. (If other calls are available at the site, they also
can be heard but they will not be actively dragged.)
(Default)
The default emergency talk group, as well as any emergency-enabled talk groups, is only
dragged if it is in emergency mode.
Functions the same as Normal Scan Mode, except the priority groups are fixed to the
selected profile’s pre-defined P1 and P2 groups (configured via the UAS). In this mode,
P1 and P2 groups CANNOT be locked out.
Fixed
7.25.1 Checking or Changing Active Scan Mode
The currently active scan mode does not appear in the dwell display. To check it, access “ScnModeMenu”
and observe it in the top line of the display. To change the active scan mode:
1. Use
2. Use
to scroll through the menus until “ScnModeMenu” appears in the display.
to scroll through the scan options until the desired mode appears. See Table 7-6.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7.25.2 Scanning Priority
The following lists the scanning priority order (from highest to lowest):
1. Selected talk group in emergency state
2. Default emergency group in emergency state
3. Selected talk group
4. Emergency capable group in emergency state
5. Priority 1 talk group
6. Priority 2 talk group
7. Other (non-priority)
7.25.2.1 Changing Scanning Priority
Follow this procedure to set talk groups in the current profile as the Priority 1 or Priority 2 talk group:
1. Use
to scroll through the menu until “Priority1” or “Priority2” appears in the bottom line of
the display (Priority1 group has higher priority than the Priority2 group. The talk group currently set
as the priority talk group appears in the top line of the display.
2. Use
to select a new priority talk group.
3. Press the MENU button to set the newly selected talk group as the priority talk group.
7.26 MAKING SELECTIVE CALLS
Selective calling is a feature that allows two radio units to obtain and utilize an independent voice path for
a private call. Radios can be configured to both initiate and receive selective calls or to only receive
selective calls.
In the OpenSky system, a source radio can be configured to initiate selective calls through a pre-
programmed list in memory. This method uses the “speed dial list” set up by the OpenSky network
administrator and provisioned as part of the registration process.
In addition, a properly equipped source radio can initiate a selective call to any radio in the system by
entering the ten-digit voice user ID (which looks like a telephone number) of the target device. Entering a
selective call number without using the speed dial feature requires a system model control head (Figure
Selective calls are terminated if an emergency is declared. The network limits selective
calls to ten (10) minutes maximum.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7.26.1 Manually Dialing a Selective Call (System Model Control Head)
1. Press *8 on the keypad.
2. Enter the number of the radio to be called (e.g., 027-001-0006). If the region number (first 3 digits;
027 in this example) is the same as this radio’s region number, these digits do not need to be entered.
Likewise, if the region and agency numbers (first 6 digits; 027-001 in this example) are the same as
this radio’s numbers, these digits do not need to be entered. Leading zeros can also be ignored.
3. Press and release the # key.
4. Wait approximately two (2) seconds.
5. Press and release the PTT button to initiate the selective call request. When the called party accepts
the call, press the PTT again and begin speaking.
7.26.2 Speed Dialing a Selective Call
Speed dial numbers are defined and provisioned by the OpenSky network administrator
and cannot be manually entered into the radio by the user. Contact the administrator if
changes to the speed dial list are required.
1. Scroll through the Menu options using
display.
until “SpeedDial” appears in the bottom line of the
2. Using
, scroll through the pre-programmed speed-dial numbers until the desired number
appears in the display.
3. Press and release the PTT button to ring the other user.
a. The ring tone is sounded.
b. If the other user accepts the call, the called user’s alias will appear in the initiating caller’s
display. The two are now in a private call until one ends the call, the call is terminated due to an
initiated emergency, or the maximum time limit of ten (10) minutes is reached.
4. To end the call, press the # button or (-) using
.
7.26.3 Receiving a Selective Call
When someone calls in from another radio using the selective call function, a ring sounds in the speaker
and/or headset. Press up or down using or any number key to accept an incoming Selective Call.
Press the microphone’s PTT button when speaking (transmitting) to the caller.
Press the # button or (-) using to reject an incoming Selective Call.
A selective call will be interrupted if an emergency is declared on a monitored talk group.
7.26.4 Terminating a Selective Call
Press the # button or (-) using
to terminate an incoming Selective Call.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7.27 SELECTIVE ALERT
Selective alert messaging is an OTP feature allowing one of up to eight (8) pre-programmed text
messages (refer to Section 7.27.3) to be sent from one radio to another. The user specifies a destination
radio’s User ID, selects one of the pre-programmed text messages, and then transmits it to the destination
radio. The message delivery system adds time-of-day information and forwards the message to the
destination (receiving) radio. The sending radio receives a brief message noting the status of the
The first few characters of a message are part of the message text entered when the message is
programmed. This programming is performed by the system or network administration personnel.
Messages successfully received by the destination radio are stored until deleted or until the radio is power
cycled.
7.27.1 Sending Selective Alert Messages
The destination radio’s User ID can be selected via the menu or via the keypad on the system model
control head.
Menu Button Method:
1. Using
, scroll through the menu until “AlertDest” (Alert Destination) appears in the bottom
line of the display. The current speed dial number scrolls on the top line.
2. Use
to change to a different speed-dial number.
3. When the desired speed-dial number appears, press the MENU button to activate the selection.
4. Choose and send the message.
Keypad Method (System Model Control Head):
To select the destination radio’s User ID using the keypad, perform the following:
1. Press *7 on the keypad. “AlertDest” appears in the display.
2. Enter the number of the destination radio (e.g., 027-001-0006) using the DTMF keypad. If the region
example) are the same as this radio’s numbers, these digits do not need to be entered. Leading zeros
3. Press the # key to enter the number.
Choosing and Sending the Message
After specifying the destination radio’s User ID (Section 7.27.1), the radio automatically allows you to
choose a message. The current message scrolls across the top line of the display. To choose a message:
1. Scroll through the message list using
. The next available message in the list is displayed.
Pause between each arrow button press to observe the entire message as it scrolls across the top line
of the display.
2. To select and send the displayed message, press the Select button, or press the # button on the
keypad.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
Table 7-7: Status of Selective Alert
STATUS MESSAGE
DEFINITION
Delivering
Busy
Select Alert message transmit attempt
Too busy – Try again
Dest Down
Not Reg
Delivered
Unreachable
Partial
Receiving radio not logged on – Not registered
Transmitting radio not logged on – Not registered
Transmission complete
No response
Transmission interrupted
7.27.2 Receiving Messages
When a selective alert message is received by a radio, a four-beep tone (one low, two high, and one low)
is heard and “NewAlert” flashes until the new message is read. Up to eight (8) received messages are
stored. If another message is received, the first (oldest) message is automatically deleted to make room for
new incoming messages.
Displaying Received Messages
1. Using
, scroll through the menu until “AlertsRecvd” (Alerts Received) appears in the bottom
line of the display. “No alerts” or the last received (newest) message appears in the display. It is
preceded by the time the message was received, and the sender’s name/alias.
2. View other received messages using
.
3. To delete the message currently being viewed, press the MENU button.
Deleting Received Messages
To delete a received message:
1. Display the message.
2. Delete the message by pressing the MENU button.
3. Confirm the deletion by pressing the MENU button again.
7.27.3 Defining Pre-Programmed Messages
All selective alert messages are pre-defined by the radio system’s maintenance personnel. These messages
are sometimes referred to as “canned” messages. Custom selective alert messages cannot be created by
the radio user. The entire selective alert message, including the abbreviation, can include up to 99 text
characters.
7.28 TELEPHONE INTERCONNECT CALLS (SYSTEM MODEL CONTROL
HEAD)
7.28.1 Placing an Interconnect Call
If the radio system is equipped with Public Switched Telephone Network (PSTN) interconnect
equipment, telephone calls can be made from the M7200 using this procedure:
37
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
1. Press the * 9 keys.
2. Enter the telephone number. Ignore dashes/spaces, and precede the number with any required access
digits such as a 1 for long distance.
3. Press the # key.
4. Wait a few seconds and then press and release the mic’s PTT button to initiate the call. An initial ring
tone plays indicating call initiation. Once the gateway picks up the call, another ring tone sounds.
5. When the caller answers, press the PTT button when speaking and release it to listen to the caller.
6. To hang-up, press the # button or (-) using
.
7.28.2 Receiving an Interconnect Call
When receiving an Interconnect Call, a ring sounds in the speaker and/or headset. Press up or down using
or any number key to accept an incoming Interconnect Call. Press the microphone’s PTT button
when speaking (transmitting) to the caller.
Press the # button or (-) using
to reject an incoming Interconnect Call.
7.29 EMERGENCY COMMUNICATIONS
The M7200 mobile radio can transmit both emergency voice calls and emergency alerts over the entire
network. OpenSky handles emergency calls and alerts with the highest priority.
For critical voice communications, an emergency call can be raised on the default talk group or the
currently selected talk group by “declaring” an emergency on the talk group. The exact talk group is
determined by the currently active profile. After successfully declaring an emergency on a talk group, the
declaring radio’s microphone remains “hot” for a predetermined amount of time. In other words, the radio
transmits audio for a period of time even when the microphone’s PTT button is not pressed. An
emergency talk group is provided greater priority and infinite hang-time by the radio system’s
infrastructure. Hang-time is the maximum duration of quiet time between transmissions on the talk group
before the infrastructure assets are automatically taken away. Because an emergency call is handled on a
talk group, it is received by all radios and consoles monitoring the talk group.
An emergency alert is a data message sent by the radio to the MIS console (or any console capable of
receiving it). It identifies the radio declaring the emergency, and the radio’s location (if the radio is
equipped with a GPS receiver). Voice audio is not automatically transmitted during the emergency
if the administrator configures the radio for alert notification only.
7.29.1 Declaring an Emergency Call or Alert
Press the red emergency button on the radio to enter emergency mode. The emergency is raised after the
emergency raise delay [default is one (1) second].
•
If the active profile of the unit initiating the emergency is configured for Emergency Alert, the
emergency alert signal is sent to registered alert servers, such as the dispatcher console.
•
If the active profile of the unit initiating the emergency is configured for Emergency Call, the
talkgroup is placed into emergency status notifying other radios and the emergency alert signal is sent
to the dispatcher console.
•
If the emergency behavior of the active profile is Current, the active, selected voice group becomes
the default emergency voice group.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
•
If the emergency behavior of the active profile is Default, the radio moves to the default emergency
voice group of the profile and this talk group becomes the select talk group.
The display will alternate between the emergency voice group name and “EMERGENCY” and declaring
User ID to indicate that the emergency has been initiated.
7.29.2 Silent Emergency
When this feature is enabled and an emergency call or alert is declared by pressing the emergency button,
the radio will not play a tone and will display an abbreviated emergency message (default is EBA). This
feature is enabled or disabled via programming or via the menu.
If the Silent Emergency feature is enabled or disabled via programming, the setting will
survive power cycle. Enable/Disable selection via the menu will NOT survive power cycle
and the enable/disable state will revert to the programmed setting at power up.
7.29.3 Clearing an Emergency Call or Alert
Check with the system administrator to ensure that the radio is programmed to allow an
emergency to be cleared.
If enabled via programming, clear an emergency by:
1. Pressing and holding the CLR/CLEAR button and simultaneously pressing the emergency button.
2. After the Emergency Cleared Tone sounds, release both buttons.
If the radio is in stealth mode, clearing the emergency will take the radio out of stealth
mode.
7.29.4 Receiving an Emergency Call
Upon receiving an emergency call declared by another radio:
•
•
An emergency tone sounds in the radio’s speaker/headset (three short high-pitched beeps).
“EMERGENCY” flashes in the display if the radio is not in stealth mode. When receiving voice in an
active emergency, the flashing “EMERGENCY” is inhibited so that the alias of the sender can be
seen.
•
•
•
On receiving radios with the emergency talk group selected, the alias of the sending party is displayed
for 5 seconds during the open-mic period, then the word “Emergency” flashes on the second line of
the display and continues until the emergency state ends.
If scan mode is set to “No Scan” and the emergency was declared on the selected talk group, audio on
“No Scan” operation.
If scan mode is set to “No Scan” and the emergency was declared on a talk group other than the
selected talk group, the emergency talk group (identified by an “*”) must be selected before audio on
it is heard in the speaker/headset.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
•
•
If scan mode is set to “Normal” and the emergency was declared on the selected talk group, the
selected/emergency talk group’s name remains in the top line of the display. Audio on the emergency
talk group is heard in the speaker/headset.
If scan mode is set to “Normal” and the emergency was declared on a talk group other than the
selected talk group, the emergency talk group’s name appears in the bottom line of the display. Audio
on the emergency talk group is heard in the speaker/headset.
•
•
The declaring radio's alias appears in the bottom line of the display when the emergency talk group is
selected.
An emergency call can be dismissed as described in the following section.
A radio declaring an emergency on a talk group has a “hot” mic time period of typically
ten (10) seconds just after it declares the emergency. This time period may be adjusted
by system or network administration personnel on a per radio basis.
7.29.5 Dismissing an Emergency Call
An emergency is dismissed for a configurable amount of time only (default = 5 minutes).
To ignore an emergency call declared by another radio user:
1. Press
2. Press
until “EmgDismiss” appears in the display.
until the talk group in the emergency state appears, as indicated by an asterisk (*)
following the talk group’s name.
3. Press the MENU button.
The emergency dismiss timer is cleared when the emergency is cleared.
7.30 ENCRYPTION
In the OpenSky network, both data and voice use a 128-bit or 256-bit key encryption standard published
by the Federal Information Processing Service (FIPS), called Advanced Encryption Standard (AES). AES
is approved by the U.S. Department of Commerce for encryption of classified materials.
When encryption is enabled on the network, data is encrypted from the MDIS to the Mobile End System
(MES) (e.g., M7200 mobile radio). This form of encryption provides air-link security.
Voice encryption is handled either automatically or manually. Automatic encryption is initiated through
the Unified Administration Server (UAS) for a specific talk group and requires nothing from the user.
Manual encryption is initiated by two or more radio users and requires system model control heads. Both
methods of encryption are discussed in the following sections.
7.30.1 Automatic Encryption
For automatic encryption, a network administrator will select the talk group to be encrypted at the
interface to the UAS. Once the talk groups have been selected and identified as secure, credentials for key
40
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
generation are generated automatically by the system and provisioned to authorized users. This process
requires that authorized users login to the network and be authenticated. Encryption keys require no
manual handling and are never sent “in the clear” over any network interface or air-link.
1. “Pls Login” appears displayed in the bottom line of the dwell display.
2. Login normally using the keypad on a system model control head to enter User ID and Password.
If a user is engaged in a call on a talk group encrypted at the network administrator level, “Secure Call”
will appear in the bottom line of the dwell display if the user is logged in to that talk group.
If a secure call is in progress elsewhere and the user has not logged in, the bottom of the dwell display
will alternate between “No Access” and the alias of the radio that is currently engaged in the secure call.
7.30.2 Manual Encryption (System Model)
Two or more users can manually encrypt a call, if enabled, without an established encrypted talk group. A
pre-determined key is required at each radio.
The key must be pre-determined by the users prior to making a manually encrypted call
on a talk group and is entered into the radio using the keypad. For 128 bit encryption, this
key is between 1 and 16 digits. For 256 bit encryption, this key is between 17 and 32
digits.
If two communicating radios have different (manually-defined) keys, receive audio at
each radio will sound garbled.
With manual encryption enabled, unencrypted radio users on the talk group can still make standard voice
(unencrypted) calls on the talk group. However, if an unencrypted user attempts to transmit on the talk
group when one of the encrypted users is already transmitting on the talk group, the unencrypted radio
will sound a deny tone and “No Access” will appear in the display. Also, the encrypted user can hear
standard unencrypted calls, but cannot respond while still manually encrypted.
Do not set a talk group for manual encryption if it has been set for encryption by the
network administration personnel.
CAUTION
Perform the following to transmit or receive manually encrypted calls:
1. Press *32 on the keypad.
2. Enter the key (1 – 16 digits for 128 bit encryption; 17 – 32 digits for 256 bit encryption).
3. Press the # key.
4. To end manual encryption, press *33#.
If a user is engaged in a call on a talk group that has been manually encrypted at the radio level, the user
will see “Secure Call” on the bottom of the dwell display.
If a secure (encrypted) call is in progress, and the user has not entered the key, the bottom of the dwell
display will alternate between “No Access” and the alias of the radio that is currently engaged in the
secure call.
Once the user has terminated manual encryption, “UnSecure” appears temporarily in the bottom line of
the dwell display.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
7.31 PRESET BUTTONS
The front panel contains three buttons labeled A, B, and C. By holding one of these buttons down for
approximately three (3) seconds, the following current information is saved to the function of that button:
•
•
•
•
•
•
Selected talk group
Selected profile
Selected priority talk group
Lockouts
Scan mode
Intercom mode
Presets are saved and restored to/from non-volatile memory. Changing the User ID (login in as a different
user) will clear the presets since they are stored on a per-user basis. Changing control heads will not recall
presets for the previous control head.
Preset button C can be configured via programming to reboot the radio into a particular
application mode. Contact your system administrator to determine if this feature is
enabled in your radio.
7.32 DYNAMIC REGROUPING
Dynamic regrouping requires that the network administrator determine which radio users should be
formed into an impromptu talk group to respond to particular emergency conditions.
The administrator will edit the personalities of the affected radios to include an emergency profile and
then page the affected radios to re-register with the network to receive their edited personalities.
In response, affected radios automatically re-register to receive their edited personalities. During re-
registration, subscriber equipment will default to the emergency profile selected by the administrator.
7.33 GPS COORDINATES
The radio’s current latitude and longitude coordinates may be displayed using the “GPS” menu. The
following procedure assumes a GPS antenna is connected to the radio and it is receiving adequate signals
from GPS satellites:
1. Press
until the “GPS” menu appears in the bottom line of the display. Current GPS coordinate
latitude and longitude data continuously scrolls in the top line of the display in a
degrees:minutes:seconds format.
2. Use
to change to another menu.
If the internal GPS receiver’s data is expired (30 minutes or more) or unavailable, the
radio uses the serving base station’s coordinates [GPS (Site) is displayed]. The GPS Menu
will also indicate if the data is aged (2 minutes or more) [GPS (Aged) is displayed]
42
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
8 P25/EDACS/CONVENTIONAL COMMON OPERATION
8.1 CH721 FRONT PANEL COMPONENTS
The front panel of the control head includes a dot matrix display, controls for menu navigation, an
emergency button, three pre-set buttons, a Power On-Off/Volume Control knob, and a microphone
connector. In addition, the system model control head features a DTMF keypad.
Table 8-1 lists all default front panel controls and their functions. All functions and controls of the Scan
radio operate the same as the corresponding functions and controls on the System radio.
Figure 8-1: System Model
Figure 8-2: Scan Model
Button function may vary depending upon system programming, radio hardware, and
remapped to provide new functions.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
Table 8-1: Front Panel Default Controls and Functions
PART
FUNCTION
Power On-
Off/Volume
Control knob
Turn knob clockwise to power on the radio and increase volume.
Turn counter-clockwise to decrease volume and power off the radio.
Mic Connection
Connection for hand-held, hands-free, speaker-mic, or headset.
The Emergency button declares an emergency if enabled through programming.
Ambient Light
Sensor
Radio automatically adjusts the display and button backlight brightness level based
on ambient light. Do not block this sensor.
This rotary switch selects the systems or groups/channels, depending upon
programming.
This rocker type button is used to display the current SCAN status for a
group/channel and then add or delete the group/channel from the system scan list.
Pressing the add/delete button twice while the radio is actively receiving or three
times when the radio is not receiving selects the last scanned channel (Last
Scanned Channel Recall).
The primary function of this rocker type button is to scroll through the System list or
the Group/Channel list depending upon programming.
The secondary function is to increment or decrement items within a list (phone list
for example).
OPT/OPTION
CLR/CLEAR
Toggle a PC programmable feature ON and OFF.
In Trunked mode, the CLR button exits the current operation and removes all
displays associated with it. The radio and display then return to the group receive
state.
In Conventional mode, pressing this button unmutes the receiver so activity on the
selected channel can be monitored. When pressed and held for approximately 3
seconds, this button toggles conventional channel decoding (Channel Guard,
Digital Channel Guard, T99) ON and OFF if programmed for the selected channel.
Primary function - access the menu list. This is a list of additional features that are
not available directly from the keypad.
MENU
SCAN
Secondary function - activate a selected item within a list, similar to an enter key.
Primary function - toggle scan operation on and OFF.
Secondary function - toggle the keypad buttons between their primary function and
their secondary function.
Pre-Set buttons
Used to store and recall user-selectable parameters.
(A, B, & C)
SYS
GRP
STS
MSG
Used to enter the System select mode.
Used to enter the Group select mode.
Permits the transmission of a pre-programmed status message to an EDACS site.
Permits the transmission of a pre-programmed message to an EDACS site.
Used to place telephone calls through the radio by selecting the interconnect
special call function.
PHN
44
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
PART
DIS
FUNCTION
Used to adjust the current display intensity and the keypad backlight level.
IND
Used to call an individual or make an all-call by selecting the individual call function.
8.1.1 Primary Functions (Quick Access)
The secondary function of the SCAN button is to toggle the keypad buttons between their primary
function and their secondary function. When the secondary keypad is active, i.e. entering phone digits for
an interconnect call, the SCAN button can be used to toggle the keypad buttons back to their primary
function, perform a task, and then toggle back to finish entering the digits for the phone number.
PRIMARY is displayed when the SCAN button is used to toggle the keypad keys back to their primary
functions. This provides quick access to the primary functions of the keypad. This is a programmable
feature of the SCAN button only. Careful consideration should be given to possible operational conflicts
before enabling this feature.
Several keys on the Scan version have a secondary function. The MENU key is the SELECT secondary
function with the CLEAR key remaining the same for the secondary function. On the System version, the
OPT has a secondary function of DELETE, MENU is SELECT, and CLR retains its CLEAR
functionality.
8.2 TURNING THE RADIO ON
Rotate the POWER ON-OFF/VOLUME knob clockwise, out of detent to turn the radio on. A short
beep (if enabled through programming) indicates the radio is ready for operation. The display indicates, if
programmed, the last selected system name on line 1 and the last selected group or channel name on line
2.
8.3 SELECTION MODE RULES
Many operations require selection from a list such as system, group or phone number. This selection
process is handled in the same manner for all lists. The
ramp control, MENU, 0-9, *, #, and the
CLR button are used during the selection process. The following example systems list is used to explain
the process:
The hookswitch functions the same as the CLR key in I-Call, phone call, and menu
modes.
SYSTEM
1
2
3
4
NORTH
SOUTH
EAST
WEST
After entering a selection mode, the following generic display format will appear:
X X X X X X X X
Y Y Y = Z Z Z
45
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
Line 1 shows the currently selected item name (XXXXXXXX) from the list. Line 2 indicates the list
(YYY) that the selection is to be made from and the number of the selected item (ZZZ) within the list. (In
some cases the information on lines 1 and 2 will be exchanged.) Enter the system selection mode by
pressing the SYS key. If SYSTEM 2 is the current selection, the display appears as follows:
S O U T H
S Y S
=
2
Line 1 contains the current system name, SOUTH; and line 2, SYS = 2, indicates that selection is from
the system list and it is the second system within the list.
A new system from the list is selected by using the
ramp control or by directly entering the system
number with the numeric keys. The ramp control scrolls through the list in increasing and
decreasing order. In the previous example, pressing up with the
system as shown in the next display.
ramp control selects the EAST
E A S T
S Y S
=
3
The radio can be programmed to wrap around from one end of a list to the other end or to stop at the ends.
8.4 DIRECT ACCESS
To directly access a selection, enter the corresponding number (e.g. 4) followed by MENU to activate the
selection. The entered number is displayed on line 2 as shown below. Line 1 shows the current list being
used for selection.
S E L S Y S
4
If a mistake is made while entering the number, press the DEL button to backspace once and correct the
entry. If an invalid number is entered, a short low-pitched tone sounds when MENU is pressed.
To exit the selection mode, press the CLR button or wait for the time-out. If the selection mode is cleared
while an entry is pending (i.e., numbers are entered on line 2, but MENU has not been pressed), the entry
on line 2 will be disregarded and the previous selection will remain active. If the time-out activates while
an entry is pending, the entry on line 2 will be selected if it is within the valid range; if it is out of range,
the entry on line 2 will be disregarded and the previous selection will remain active.
While in system, group or channel selection mode, the radio continues to receive calls
normally and continues scanning, if it is enabled. If a call is received during the
selection mode process the radio will return to the normal receive mode display.
Continuing with the selection process will return the display to the same point in the
selection process if the selection mode time out has not yet expired. Any press of the
PTT button during the selection mode process will initiate transmission and exit the
selection mode.
8.5 FEATURE ENCRYPTION DISPLAY
Feature Encryption Display is available through the menu function and, if programmed, appears in the
menu as “FEATURES.” This data indicates current features programmed into the radio as well as
information required to add features to the radio.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
Once the feature has been accessed, all normal menu functions work. The user can scroll up or down
through all of the entries.
Feature Encryption Display provides the ability to view, in the order displayed, the following:
•
•
•
•
Serial number ROM data - serial number of the ROM
Feature encryption data stream - used to enable features
Number Fields - defines limits
Features enabled - displays bit fields of enabled features
8.5.1 Serial Number ROM (12 Hex Digits)
Example:
When the user wants to enable a feature in his radio, he will need to call M/A-COM, Inc. They will ask
for the ROM serial number. The serial number shown here is for example only.
8.5.2 Feature Encryption Data Stream
Example:
These data streams define the features the user has enabled in his radio and are required by M/A-COM,
Inc. to enable other features. The data streams shown here are for example only. Note: There are three
displays: FD1, FD2, and FD3. All three are required.
Number Fields
Example:
47
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
These number fields show the set limits of the of the user's radio as:
•
•
•
SG# XXX - Maximum number of system/groups combination available
SY# XXX - Maximum trunked system limit
CH# XXX - Maximum number of conventional channels available
The user needs to know the limits of his radio before attempting to enable other features. The numbers
shown here are for example only.
8.5.3 Features Enabled
These numbers indicate which features are enabled.
Example:
Table 8-2 lists possible features available in the user's radio.
Table 8-2: Available Feature Numbers
FEATURE
NUMBER
STANDARD OR
OPTIONAL
POSSIBLE FEATURES
Conventional Priority Scan
01
04
05
06
07
08
09
10
12
14
16
17
21
22
23
29
32
Standard
Standard
Optional
Optional
Standard
Standard
Standard
Standard
Optional
Optional
Optional
Optional
Optional
Optional
Standard
Optional
Optional
Group Scan (EDACS and P25 Trunked)
Priority System Scan (EDACS only)
WAscan/ProSound™/ProScan (EDACS only)
Dynamic Regroup
EDACS Emergency
Type 99 Encode
Conventional Emergency
Aegis™ Digital Voice Encryption
DES Encryption
Mobile Data
Status/Message (EDACS only)
EDACS Security Key (ESK)
ProFile™ (EDACS only)
Narrowband
ProVoice
FIPS-140-2
48
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
FEATURE
NUMBER
STANDARD OR
POSSIBLE FEATURES
P25 Common Air Interface
OPTIONAL
33
34
38
Optional
Direct Frequency Entry
Radio TextLink
Optional
Optional
8.6 SYSTEM/GROUP/CHANNEL SELECTION
In the following description of SYSTEM/GROUP/CHANNEL SELECTION, the term group is used
for both group and channel.
The M7200 SYSTEM/GROUP/CHANNEL knob and the
ramp control are programmable for
maximum flexibility. If the SYSTEM/GROUP/CHANNEL knob is assigned to select groups, then the
ramp control is assigned to select systems. If the SYSTEM/GROUP/CHANNEL knob is assigned
to select systems, then the
ramp control is assigned to select groups. System, group, and channel
selection is the primary function for these controls.
Either systems or groups can also be selected by entering the select mode and following the selection
mode rules described earlier. The system select or group select modes are entered by pressing SYS or
GRP, respectively, from the standard receive mode. Using the
ramp control after entering a
particular selection mode in this manner is the secondary function of these keys.
8.6.1 System Selection
Several methods, some of which depend on programming, can be used to select a new system. These
procedures are presumed to be starting from the normal receive display.
METHOD 1: If system selection is programmed to the SYSTEM/GROUP/CHANNEL knob, select a
system by turning the SYSTEM/GROUP/CHANNEL knob to the desired system
position. The display registers the new system name on line 1. If the wrap option is OFF
and the knob is moved to a position greater than the number of programmed systems, the
highest programmed system will remain selected.
METHOD 2:
If system selection is programmed as the primary function of the
ramp control,
select a system by pressing up or down to scroll through the system list. The display
registers the new system name on line 1.
METHOD 3: Press SYS to enter the system select mode and follow the selection mode rules detailed
earlier. Use the ramp control to scroll through the systems.
8.6.2 Group and Channel Selection
Several methods, some of which depend on programming, can be used to select a new group or channel.
These procedures assume starting from the normal receive display.
METHOD 1:
If group selection is programmed to the SYSTEM/GROUP/CHANNEL knob, select a
group by turning the SYSTEM/GROUP/CHANNEL knob to the desired group. The
display registers the new group name on line 2. If the wrap option is OFF and the knob
is moved to a position greater than the number of programmed groups, the highest
programmed group will remain selected.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
METHOD 2:
If group selection is programmed as the primary function of the
ramp control,
select a group by pressing up or down, to scroll through the group list. The display
registers the new group name on line 2.
METHOD 3:
Press GRP to enter the group select mode and follow the selection mode rules detailed
earlier. Use the
ramp control to scroll through different groups.
8.7 LAST SYSTEM/GROUP/CHANNEL RECALL
This feature, enabled through programming, allows the user to recall the last selected system/group after
an emergency or home function or system/group key function. For example, if the Home button (pre-
programmed) is pressed, the radio will go to the designated Home system/group or channel. If the Home
button is pressed again, the radio returns to the previous system/group or channel. At this time, the user
can toggle between the Home system/group or channel and the previous system/group or channel. The
operation is the same for the SG1-SG5 buttons.
8.8 DIGITAL VOICE OPERATION (PROVOICE)
8.8.1 Voice Modes
Each system (trunked or conventional) in the radio is programmed for no digital voice operation (analog
only) or digital voice format ProVoice. ProVoice programmed systems have three (3) different voice
modes: clear (analog), digital, and private. The voice modes are programmed on a per-group basis within
each trunked system and on a per-channel basis within each conventional system. A radio must be
equipped with the encrypt/decrypt option before it will operate in private mode.
Current ProVoice Conventional operation is for talk-around mode only.
Table 8-3: Transmit/Receive Mode Compatibility for ProVoice Operation
GROUP/CHANNEL
PROGRAMMING
(TRANSMIT)
CLEAR
RECEIVE
DIGITAL
RECEIVE
PRIVATE
RECEIVE
CLEAR
Yes
Yes
Yes
No
Yes
No
No
No
DIGITAL
PRIVATE
Yes
8.8.2 Clear Modes
In Clear Mode, the radio transmits and receives only clear (analog) voice signals. These analog signals are
non-digitized and non-encrypted. Clear Mode transmissions can easily be monitored by unauthorized
persons. Groups or channels programmed for clear operation cannot transmit or receive unencrypted
digital or private messages.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
8.8.3 ProVoice Digital Mode
ProVoice digital mode allows the radio to transmit and receive digitized voice signals. These digital
signals provide improved weak signal performance and they cannot be easily monitored with a standard
receiver. Groups and channels programmed for ProVoice digital operation transmit only digital signals.
Private calls cannot be received or transmitted when the radio is in ProVoice digital mode because the
radio does not know the cryptographic key used.
Message trunked group calls and individual calls will be answered back in the mode they were received,
assuming the call or hang time is still active. Individual, phone, all and emergency calls will be
transmitted clear if digital mode is disabled or inoperative.
•
If receiving an analog message trunked call, the radio will respond in analog mode during the hang
time on the working channel.
•
•
If receiving an analog I-Call, the radio will respond in analog mode during the hang time.
When using the "WHC" feature to respond to an I-Call (after the hang time has expired), the call will
be transmitted in the mode defined by the system mode as programmed for the current system if the
ID being called is not in the I-Call list. If the ID is in the I-Call list, then the call will be transmitted as
defined by the I-Call mode programmed in the list for that ID.
DTMF
The overdial and hot keypad features for transmitting DTMF tones are not available while in ProVoice
Digital Mode.
ERROR Messages
If any of the following error messages are displayed, the radio was either programmed incorrectly or
needs servicing:
DSP ERR
DSP ERR
DIGV ERR
ERR=xxxx
Power Up Only
If the ProVoice circuit board is not responding, correctly, one of the following error messages will be
displayed and the radio needs servicing:
HARDWARE
ERR= 3X
3X will be a number between 30 and 38
8.8.4 ProVoice Private Mode
ProVoice private mode allows the radio to transmit encrypted messages and receive clear or private
transmissions. The radio will transmit private if the group/channel is programmed for private operation
and forced operation is pre-programmed.
If the radio was pre-programmed for auto-select, the radio will transmit in the following modes;
•
If Private mode is enabled, transmissions are always in private mode.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
•
If Private mode is disabled and a private call is received, the Reply transmission will be in Private
mode if the transmission is made during the scan hangtime. If the reply transmission occurs after the
scan hangtime, the transmission will be in Clear mode.
When operating on a group or channel programmed for private mode, all transmissions will be private
transmissions and the radio will receive clear and private signals. If the selected group or channel is
programmed for auto-select capability, the mode can be toggled between private and clear with the OPT
or OPTION button. Radios programmed for forced private operation do not allow a change of the
transmit mode; therefore, the OPT or OPTION has no effect.
8.8.4.1 Displaying the Currently Used Cryptographic Key Number
To display the cryptographic key currently in use for either the system encryption key (for special call
such as individual, phone, all, agency or fleet) or the group/channel key (for group or conventional calls),
perform the following procedure (Not Available on Conventional radios):
1. Press the MENU button.
2. Use
to select DISP KEY. Then press the MENU button.
3. Then use
to toggle between displaying the system key or the group/channel key.
Table 8-4: Current Cryptographic Key Display
ENCRYPTION KEY
DISPLAYED
MESSAGE DISPLAYED
"SYS KEY"
"KEY = 1"
System
Group/Channel
"GRP KEY"/"CHN KEY"
"KEY = 2"/KEY = 2"
8.8.4.2 Key Zero
All cryptographic keys can be zeroed (erased from radio memory) by pressing the CLR button (System
Model) or CLEAR (Scan Model) and while still pressing this button, press and hold the OPT button
(System Model) or OPTION (Scan Model). Press both buttons for 2 seconds. A series of warning beeps
will begin at the start of this 2-second period and then switch to a solid tone after the keys have been
zeroed. The display will indicate KEY ZERO.
If the cryptographic key(s) are zeroed, one or more keys must be transferred from the Key Loader into the
radio before private communications can continue. (Refer to Key Manager TQS3416 Administration and
Software Release Notes for further information.)
8.8.5 Private Operation
8.8.5.1 Receiving an Encrypted Call
When receiving, the radio automatically switches between clear or private operation. If the transmission
being received is an encrypted transmission, it will be decrypted, the receiver will unsquelch and the
message will be heard in the speaker. The selected group or channel must be programmed for private
operation and the correct cryptographic key must be loaded into the radio for this to occur.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
8.8.5.2 Transmitting an Encrypted Call
1. Select the desired group or channel.
2. Place the radio in private mode by pressing the OPT button (System Model) or OPTION (Scan
Model).
If the last state of the radio was private mode, the private mode will be enabled on power up. In
addition, the private mode will be enabled if forced operation has been programmed in the radio
If a group or channel is not programmed for private mode operation, PVT DIS will be displayed if an
attempt is made to enable private transmit mode. It is not possible to operate on this group/channel in
private mode.
If the radio is programmed for forced private transmit operation, FRCD PVT will be displayed if an
attempt is made to disable private transmit mode. It is not possible to transmit on this group/channel
in clear mode.
If the radio does not have the correct encryption key loaded, NO KEY # will be displayed and the
call will not be transmitted.
3. Continue with standard transmission procedures. A private mode access tone will be heard when the
PTT button is pressed.
8.8.5.3 Scanned Group Calls
Receiving a scanned group call is the same as receiving a selected group call. During the scan hang time,
if the radio was programmed for auto-select, it will transmit back in the same mode it received the call.
For example, if a clear group is entered in the scan list, it will only receive clear calls. If the same group
was available in private and entered in the scan list, it can receive clear and private calls, provided auto-
select was programmed in the radio. The user can select transmitting on the scanned or selected group. If
a group is entered in the scan list more than once in different modes (clear, digital, private), only the first
occurrence of the group will be used.
8.8.6 Conventional Operation
8.8.6.1 Outside Address
The same outside address (works similar to Channel Guard operation) must be programmed in the
transmitting and receiving radios when ProVoice digital or private operation is enabled. If address is not
correct, the radios will not communicate.
8.8.6.2 Channel Guard
Channel Guard encode is transmitted on analog clear channels only. Channel Guard decode will operate
on either a clear or private channel. The exception is when G-STARTM signaling is used (see G-STAR
paragraph).
8.8.6.3 G-STAR
When G-STAR is programmed on a private channel, the radio will transmit G-STAR in clear mode and
then switch to private for the voice portion of the call. If G-STAR is sent with Channel Guard, then both
are sent in clear mode and the radio switches to private mode. Emergency G-STAR data burst is
transmitted in clear mode.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
8.9 MACRO KEY OPERATION
Macro key operation permits the user to accomplish a series of keystrokes with a single "macro"
keystroke. Up to ten (10) macro keys can be defined, each capable of executing up to twenty (20)
keystrokes, to any pushbutton input (i.e., keypad keys, buttons, etc.). Each macro key can be pre-
programmed to activate when pressed or when released.
A macro key can also be pre-programmed to change the keystroke sequence the next time the macro key
is activated.
For detail operation and assignment of macro keys, contact your communications supervisor or
administrator.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
9 EDACS AND P25 TRUNKED OPERATION
9.1 RADIO STATUS ICONS
Status icons are indicators that show the various operating characteristics of the radio.
Figure 9-1: Typical Display
Table 9-1: Icons and Descriptions
ICON
DESCRIPTION
Indicates the EDACS system is in Failsoft™ mode (if enabled through
programming).
Indicates selected group or channel is in scan list.
Indicates selected group or channel is programmed as Priority 1 in scan list.
Indicates selected group or channel is programmed as Priority 2 in scan list.
Scan mode enabled.
Volume bars – indicates relative volume level.
Indicates the current channel is set up as an analog channel.
Indicates the current channel is set up as a ProVoice channel.
Receiving or transmitting Encrypted Calls.
Special call mode (individual or telephone).
55
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
9.2 MESSAGES
During radio operation, various messages are displayed on either line 1 or line 2. Typical messages
include control channel status information, such as system busy or call denied, or messages associated
with the radio's operation, (i.e. volume adjust). These messages are described as follows:
Table 9-2: Display Messages
MESSAGE
NAME
DESCRIPTION
QUEUED
Call Queued
Indicates the system has placed the call in a request queue.
Indicates the system is busy, no channels are currently available, the queue is full or
an individual call is being attempted to a radio that is currently transmitting.
SYS BUSY
DENIED
System Busy
Call Denied
Indicates the radio is not authorized to operate on the selected system.
Indicates the control channel is lost and the radio has entered the Control Channel
Scan mode to search for the control channel.
CC SCAN
Control Channel Scan
Indicates the control channel is lost and the radio has entered the Wide Area Scan
mode to search for a new system (if enabled through programming).
WA SCAN
*RXEMER*
*TXEMER*
Wide Area Scan
Receive Emergency
Transmit Emergency
Indicates an emergency call is being received. This message will be flashing on line 2.
Indicates an emergency call has been transmitted. This message will be flashing on
line 2.
Indicates the current volume level. The volume level display ranges from OFF (silent)
to 31 (loudest).
VOL=31
Volume Level
Caller's ID Not
Received
UNKNOWN
Indicates that an individual call is being received, but the caller's ID was not received.
TX DATA
RX DATA
DATA OFF
Transmit Data
Receive Data
Data OFF
Indicates the radio is transmitting a data call.
Indicates the radio is receiving a data call. Displayed on line 2.
Indicates the radio is in the data disabled state. Displayed on line 1.
Indicates the radio has been toggled to the data enable state. Displayed for two
seconds on line 1 when toggled to enable state.
DATA ON
SYSC ON
Data ON
System Scan
Features ON
Indicates the System Scan features are enabled.
System Scan
Features OFF
SYSC OFF
PA ON
Indicates the System Scan features are disabled.
Public Address ON
Public Address OFF
Indicates that the public address function of the radio is enabled.
Momentary (2 seconds) indicates that public address function of the radio was
disabled.
PA OFF
External Alarm
Enabled
ALRM ON
ALRM OFF
PVT DIS
Indicates that the external alarm function of the radio is enabled.
External Alarm
Disabled
Momentary (2 seconds) indicates that the external alarm function of the radio was
disabled.
Private Mode
Disabled
Indicates that private mode is disabled or no encryption key has been programmed for
the selected group/channel or special call.
Forced Private
Operation
FRCD PVT
NO KEY #
Indicates that forced private operation has been pre-programmed into radio.
Encryption Key
Missing
Flashing indicator indicates that no encryption key or an incorrect encryption key is
programmed into the radio.
BCKL=1-6
GR
Backlight
Group ID
Indicates the display intensity and keypad backlight level.
Indicates that the call is a group call and is followed by the GID of the caller.
Indicates the call is an individual call and the ID number of the caller, example "ID
2725."
ID
Individual ID
56
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
MESSAGE
NAME
DESCRIPTION
This display indicates the number from the Who Has Called list. Individual calls
received but not responded to are stored in a Who Has Called list. This list is
accessible by pressing the # key and then the INDV key after the Individual call has
timed out or the Clear button is pressed. This display is on line 2 and the LID of the
caller is displayed on the top line. Currently the list is not implemented and the display
will always be WHC=1.
WHC=1
Who Has Called
Displayed when a phone call is received from the site. It is displayed in line 1 of the
display. Line 2 of the display will contain the display *INDV* when line 1 contains this
message. The radio interprets a received phone call as an individual call.
PHONE
Phone Call
Displayed when a failure of the EDACS system occurs. All communication will be in
conventional mode.
CONV FS
MENU
Conventional Failsoft
Displayed when the menu key is pressed and remains displayed in line 1 until a menu
item is selected.
The system number for the current base station of the system displayed in line 1. It is
displayed in line 2 of the display. Press the system key to obtain this display.
SYS=1-64
System = 1 - 64
Group = 1 - 64
The group number of the group displayed in line 2 of display. It is displayed in line 1 of
the display. Press the group key to obtain this display. There are up to 48 groups
available (i.e. 3 banks of 16). The maximum number of groups programmed in a radio
is determined by the personality.
GRP=1-64
INDV=1-99
Indicates which item in the individual call list is being displayed. It is displayed in line 2
of the display. The name or ID of the item in the list is displayed in line 1 of the
display.
Individual = 1 - 99
Indicates which item in the phone list is being displayed. It is displayed in line 2 of the
display. Line 1 of the display will be the last 3 characters of the list item contents.
PHN=1-99
SEL PHN
Phone = 1 - 99
Select Phone
After pressing the PHN key, selecting an entry from the phone list by typing the entry
number will display this message on Line 1.
Displayed on line 1 when an entry from the individual ID list is selected after pressing
the INDV key. The entry is a number between 1 and 32 inclusive.
SEL INDV
SYS ALL
Select Individual ID
System All Call
Displayed on line 1 to indicate a system all-call has been received.
This is code group and revision number that is displayed in line 2 when the menu item
“REVISION” is selected. The ‘gg’ is the group number of the software. The first ‘v’ is
the hardware version and ‘vv’ is the revision of the software.
Code Group and
Revision Number
Ggg-v.vv
*PHONE*
NO ENTRY
Displayed when an initiated phone call is in progress. This is displayed on line 2 of the
display.
Phone Call
Indicates that there is no data stored in one of the programmable items in either the
phone list or individual call list. The user programmable items are items 1 through 10
in each list.
INV SYS
CHN=1-99
FIX LIST
FIXED P1
Invalid System
Channel = 1 - 99
Fixed List
Displayed when the current system is an invalid type.
Displayed on line 1 of the display. This is a conventional channel index displayed
when the group key is pressed.
The Priority scan list is fixed and cannot be changed using the add or delete keys.
The Priority 1 scan channel is fixed and cannot be changed using the add or delete
keys.
Fixed Priority 1
Displayed in line 2 when the message ‘M/A-COM’ is displayed in line 1 while
displaying different items under the menu when “REVISION” is selected by the
operator.
(c) 2004
Indicates an emergency has been declared by the LID that follows the display, “EM.”
An example of this is “EM 01201.”
EM
Emergency
Displayed in line 2 of the display when an individual call is in progress (trunked and
T99 modes only).
*INDV*
Individual Call
Indicates a group call is in progress and is displayed on line 1 of the display (trunked
and T99 modes only).
*GROUP*
SPKR ON
SPKR OFF
Group Call
External Speaker ON
Displayed when the external speaker is enabled.
Displayed when the external speaker is disabled.
External Speaker
OFF
57
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
MESSAGE
NAME
DESCRIPTION
The bank of keys that are going to be loaded when the keyloader loads encryption
keys. This is only valid for radios that support VGS, VGE, or DES encryption. It is
displayed on line 2 of the display when the encryption keyloader is connected.
BANK=1-8
Indicates which group in the dynamic regroup operation has been enabled, where “x”
is a digit of 1 to 8.
REGR_0x
KEY LOAD
KEY ZERO
Dynamic Regroup
Displayed on line 1 of the display when the encryption keyloader is connected.
Displayed on line 2 of the display when the reset and option buttons are pressed
simultaneously for approximately two seconds. The encryption keys are zeroed.
Displayed on line 1 of the display in the display key mode of the menu. It is followed in
the second line with a key number “KEY = <1..7>”.
SYS KEY
GRP KEY
System Key
Group Key
Displayed on line 1 of the display in the display key mode of the menu for trunked
systems only. It is followed in the second line with a key number “KEY = <1..7>.”
Displayed on line 2 of the display in the display key mode of the menu for
conventional systems when the “SYS KEY” or “CHN KEY” is displayed in line 1 and
for trunked systems when the “SYS KEY” or “GRP KEY” is displayed in line 1.
KEY=1-7
PRIMARY
Displayed on line 1 of the display when the primary keys are enabled.
Displayed on line 1 of the display under the revision selection of the menu. The
personality name is displayed on line 2 at the same time.
PRS NAME
Personality Name
Displayed on line 1 of the display under the revision selection of the menu. The
copyright year is shown in line 2 of display at the same time “(c) 2007.”
M/A-COM
9.3 ALERT TONES
The M7200 series mobile radio also provides audible alert tones or “beeps” to indicate the various
operating conditions. These alert tones can be enabled or disabled through programming.
Table 9-3: Alert Tones
NAME
TONE
DESCRIPTION
Sounds after keying the radio (Push-To-Talk button is
pressed). Indicates the radio has been assigned a
working channel
Call Originate
A short mid-pitched tone.
After being placed in a queue or releasing the PTT
button prior to a working channel assignment, the site
calls the radio when a channel becomes available. At
this point, the radio automatically keys the transmitter
(autokey) for a short period to hold the channel. The
radio sounds a mid-pitched tone when it is clear to talk.
Immediately press the PTT button to keep the assigned
channel.
Autokey
A mid-pitched tone.
A high-pitched tone.
Sounds after pressing the PTT button indicating the
system has placed the call request in the queue. The
receiving unit(s) also sound(s) the tones to indicate they
will receive a call shortly.
Call Queued
Sounds if the radio is keyed when the system is busy, if
no channels are available for sending the message, if
the call queue is full, or if an individual call is being
attempted to a radio that is transmitting.
System Busy
Call Denied
Three low-pitched beeps.
A low-pitched tone.
Indicates the radio is not authorized on the system that
has been selected.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
NAME
TONE
DESCRIPTION
Sounds if the programmed time for continuous
transmission is exceeded. The transmitter will shut down
shortly after the alert, interrupting communications.
Release and re-key the PTT button to maintain
communications. This will reset the carrier control timer
and turn the transmitter back on.
Five
short
high-pitched
Carrier Control Timer
warning tones followed by a
long low-pitched tone.
Indicates a key has been pressed. A short low-pitched
tone indicates no action was taken because the key is
not active in the current mode.
Key Press Alert
A short tone.
In P25 trunked mode, if the receiving radio accepts a
page, both the receiving and transmitting radios emit
three high-pitched tones.
Page (P25 T Only)
Out of Range
Three high-pitched tones.
One low pitched.
Indicates the radio is in Wide Area Scan. Radio will
periodically beep when in Wide Area Scan.
9.4 MENU
The menu function accesses features that are not available directly from the keypad. The order and
specific number of menu items available is configurable through programming. Upon radio power up, the
menu item at the beginning of the menu list will always be displayed first. Subsequent access to the menu
function will return the last menu item that was shown in the display. To enter the menu mode, press
MENU. The
ramp control, and CLR are used during the selection process. All of the selection
mode rules previously detailed apply to the menu item selection process with the exception of direct
access. The radio will continue to receive and transmit normally while in the menu function.
A new item is displayed by using the
ramp control to scroll through the list in increasing and
decreasing order. The displayed menu item is made active by pressing MENU.
After entering the menu selection mode, the following generic display format will appear.
M E N U
Y Y Y Y Y Y Y Y
Line 1 indicates the radio is in the menu selection mode. Line 2 indicates the menu item (YYYYYYYY)
that is to be viewed or changed (some menu items provide radio information and do not have changeable
parameters).
59
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
An example of the menu item selection process and menu item parameter change is detailed below for the
contrast menu item.
1. Press MENU to enter the menu mode.
2. Press the
ramp control until the display shows:
M E N U
CONTRAST
3. Press MENU. The contrast menu item is activated and the display will be similar to the following:
CNTRST = X
Y Y Y Y Y Y Y Y
Line 1 shows the active menu item and its current parameter setting (XXX). Line 2 shows the
currently selected system or group name (YYYYYYYY).
4. The menu item's parameter setting shown in the display can now be changed by using the
ramp control to scroll through the list of parameter values. Once the desired setting is reached, press
MENU to store the value and return to the normal display. For menu items that display radio
information, use
to scroll through a list of informational displays. The menu items are listed in
Table 9-4: Menu Item Information
PARAMETER
SETTINGS
FEATURE
DISPLAY
Menu Item:
COMMENT
CONTRAST
Once selected:
CNTRST=
Contrast Adjust
1, 2, 3, 4, 5, 6, 7, 8
Selects the Contrast level.
Informational
Radio Revision
Information
Menu item:
REVISION
displays only
(see radio); no user
selectable settings.
Selects the information display to view.
Allows access to the Phone Call Feature.
Allows access to the Individual Call Feature.
Menu item:
PHN CALL
Once selected: See Telephone
Interconnect
Phone Call
Call Section
Menu Item:
IND CALL
Once Selected: See Individual
Call Section
Individual Call
External Alarm
EXTALARM replaces the system name on the
display as long as the external alarm feature is
enabled.
Menu Item: EXTALARM
Once Selected: EXTALARM
ON, OFF
ON, OFF
Menu item:
PUB ADDR
Once selected:
PA ON or
Public
Address
Public Address is toggled ON and OFF.
External Speaker is toggled ON and OFF.
PA OFF
Menu item:
EXT SPKR
Once selected:
SPKR ON or
SPKR OFF
External Speaker
ON, OFF
60
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
PARAMETER
SETTINGS
FEATURE
DISPLAY
COMMENT
Menu item: KEYLOAD
Once selected:
KEY LOAD BANK = N
Encryption Key
Loading
Enables the radio to accept the loading of encryption
keys.
Up to 8 banks of 7 keys
Menu item: DISP KEY
Once selected:
SYS KEY, GRP KEY or
CHN KEY and KEY = N
Display Current
Encryption
Key(s)
Displays current encryption key number.
Scan
Menu item: SCAN
ON, OFF
ON, OFF
Toggles scan function ON or OFF.
Toggles private function ON or OFF.
Menu Item: PRIVATE
Once selected: PVT or key
light.
Private Mode
Menu item: SCAN ADD
Once selected: Proper scan
icon displayed.
Scan Add
S, 2 or 1
Adds group or channel to scan list.
Menu item: SCAN DEL
Once selected: Scan icon goes
out.
Scan Delete
Scan Add/Delete
Deletes group or channel from scan list.
Menu item: SCAN A/D
When selected: Toggles
through scan selections
Toggle sequence
S, 2, 1, S, ...
Changes present group or channel to next scan choice
in scan list.
Menu Item: SCAN ADD
Last Scanned
Channel Recall
Press twice when actively
receiving; three times when not
receiving. Scan icon displayed.
Changes the selected channel to the last scanned
channel.
Menu item: HOME
Once selected: Home group or
channel displayed.
Home group or
channel selection
Changes to the group or channel defined for Home
function.
Menu item: SYS SEL
Once selected: SYS = n
1-64 = (n)umber of
desired system
System select
Displays the system selected.
External alarm #2
Menu item: EXTALRM2
ON, OFF
Toggles external alarm #2 feature ON or OFF.
Menu item: SYSGRP 1
Menu item: SYSGRP 2
Menu item: SYSGRP 3
Menu item: SYSGRP 4
Menu item: SYSGRP 5
System and group
selection
Changes to the System & Group/Channel
programmed for SYSGRP 1-5.
Toggles the mute function ON or OFF to control the
audio output from the selected radio.
Mute
Menu item: MUTE
ON, OFF
Mute #1
Mute #2
Menu item: MUTE 1
ON, OFF
ON, OFF
Toggles the mute 1 function ON or OFF on radio #1.
Toggles the mute 2 function ON or OFF on radio #2.
Menu item: MUTE 2
Multiple radio
operation
Menu item: RADIO
ON, OFF
Toggles the currently selected radio.
Menu item: RADIO 1
Menu item: RADIO 2
Menu item: NO DATA
ON, OFF
ON, OFF
ON, OFF
Changes to radio #1.
Radio selection
Changes to radio #2.
No Data
Toggles data feature ON or OFF.
EDACS Convent-
ional Priority 1
Scan
Menu item: ECP1SCAN
ON, OFF
Toggles this feature ON or OFF.
Menu item: GRP SEL
Once selected: GRP = n
1-64 = (n)umber of
desired group
Group selection
Status Condition
Displays the group selected.
Menu item: STATUS Once
selected: ST =n
0-9 = (n)umber of pre-
programmed status
Transmits the pre-programmed status message.
Transmits the pre-programmed message.
Message
Condition
Menu item: MESSAGE
Once selected: MSG =n
0-9 = (n)umber of pre-
programmed messages
Menu Item: FEATURES
Once selected:
See Feature Encryption
Display section
Indicates current features program- med into the radio
as well as certain information required to add features
to the radio (refer to the Table of Contents for Feature
Encryption Display.
Feature
Encryption
Display
Informational displays
only; no user selectable
settings
Menu Item: SYS SCAN
Once selected: SYSC ON or
SYSC OFF
System Scan
Enable
System Scan features like ProScan are toggled ON
and OFF.
ON, OFF
61
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
9.5 RECEIVING A CALL
1. Turn the radio on by rotating the POWER ON-OFF/VOLUME knob clockwise (out of detent). A
short alert signal (if enabled through programming) indicates the radio is ready to use.
2. The display shows the last selected or the power up (depending on programming) system and group
names. If the radio is unable to obtain a control channel, line 2 shows CC SCAN.
3. Adjust the POWER ON-OFF/VOLUME knob to the desired volume level.
4. Select the desired system and group. The display indicates the current system and group names.
5. The radio is now ready to receive calls.
6. When the radio receives a group call, it unmutes on the assigned working channel and the BSY
indicator comes on. Line 1 shows GR followed by the logical ID number (if received) of the unit
sending the message, or the associated name if the ID number is found in the individual call list.
9.6 SENDING A CALL
1. Turn the radio on and set the POWER ON-OFF/VOLUME knob to the desired volume level. Select
the desired system and group.
2. Press and hold the PTT button. The radio will display the system and group names and perform the
necessary signaling required to obtain a communication channel.
3. When the working channel is assigned, TX and BSY indicators are turned ON and a short beep is
sounded indicating communication can begin.
If two or more tones, or a high-pitched tone is heard, the system may be busy and the
call request has been placed in queue or the request has been denied for some reason.
4. Hold the microphone approximately three inches from the mouth and speak in a normal voice.
5. Release the PTT button when the transmission is complete and listen for a reply.
9.7 CONVENTIONAL FAILSOFT
In the unlikely event of a failure of the EDACS system, communications can take place in conventional
failsoft mode. The radio will be automatically directed to a communications channel set up for this
purpose. During this mode of operation, the control unit will display CONV FS in the alphanumeric
display. An increase in activity on the channel during conventional failsoft operation may be noticed, so
be careful not to transmit until the channel is clear.
Operation during conventional failsoft will be the same as operation on a conventional system, except that
it will not be possible to select a communications channel, or use emergency and special call. When
trunking is restored, the radio will automatically be returned to normal operation.
Emergency and Special Call are not operational during conventional Failsoft. In
addition, the GRP control will not operate.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
9.8 EMERGENCY OPERATION
The radio's ability to declare an emergency, clear an emergency, remain locked on an emergency and
group, and the emergency audio and display freeze can each be enabled or disabled through
programming. When an emergency is declared scanning will stop and will restart only after the
emergency has been cleared.
9.8.1 Receiving an Emergency Call
When receiving an emergency call from the selected group and system, an alert beep is heard and the
BSY indicator lights. The message *RXEMER* flashes in the display on line 2 until the emergency
condition is cleared. Follow standard emergency procedures.
9.8.2 Declaring an Emergency
To send an emergency call to the selected system and group (or on an optionally pre-programmed
emergency group), proceed as follows:
1. Press and hold the red emergency button for approximately one second. (This time is programmable
and therefore could be longer or shorter. Check with the system administrator.) The radio will
transmit an emergency call request with the radio ID until an emergency channel assignment is
received.
2. When the working channel assignment is received, the radio sounds a single beep (Autokey alert
tone) indicating it is ready for voice transmission. *TXEMER* flashes on line 2 in the display until
the emergency is cleared.
3. Press PTT and speak into the microphone in a normal voice.
4. Release PTT when the transmission is complete and listen for a reply.
5. The emergency can be cleared by pressing and holding the CLR button followed by pressing the red
emergency button then releasing both buttons.
9.9 SYSTEM SCAN OPERATION
The radio can be programmed with the following System Scan features. These features are automatically
enabled upon radio power up. A key or menu option is also defined to allow the System Scan features to
be toggled during radio operation. This is covered in the Menu Selection and Pre-Programmed Keypad
Key sections. The System Scan state will be maintained through system changes but will default to ON at
power up.
9.9.1 Wide Area System Scan
The M7200 Series mobile radio can be programmed for wide area system scan operation for multi-site
applications. Upon the loss of the currently selected system's control channel, radios can be programmed
to automatically scan the control channels of other systems. If a new control channel is found, the radio
will switch to the new system and sound an alert tone.
9.9.2 ProScan
The radio can be programmed for ProScan™ system scan operation for multi-site applications depending
on the version of radio flash code. ProScan provides the radio with the ability to select a new system for
the radio to communicate on, when the selected system drops below a predefined level. This is
63
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
accomplished by enabling each radio to analyze the signal quality of its current control channel and
compare it with the signal quality of the control channel for each site in its adjacency scan list. (The signal
quality metric used for the ProScan algorithm is based on a combination of both Received Signal Strength
Indicator [RSSI] and Control Channel Verification [CCV] measurements.) When the selected system’s
signal quality level degrades below a pre-programmed level, the radio will begin to look for a better
control channel. Once a control channel that exceeds the pre-programmed parameters is found, the radio
will change to the new system and emit a tone. If the control channel is completely lost the radio, will
enter Wide Area System Scanning and search the programmed adjacent systems until a suitable control
channel is found.
9.9.3 Priority System Scan
The radio can also be programmed for Priority System Scan. (To ensure that this feature operates
correctly, the control channel of the priority system must be located on channel one unless you are using
the ProScan algorithm.) The priority system is the desired or preferred system. While receiving the
control channel of the selected system, the radio will periodically leave the selected system and search for
the control channel of the priority system at a programmable rate. The programmable rate is defined by
the value in the Priority Scan Time control, (unless the ProSound/ProScan algorithm is enabled as
explained below). This priority scan timer is reset each time the PTT button is pressed or when a call is
received. If the priority system control channel is found, or meets the predefined ProScan criteria, the
radio will automatically switch to the priority system.
9.9.4 When Wide Area System Scan Is Enabled
If the radio cannot find the control channel of the selected system and begins Wide Area System Scan
(WA Scan), the radio will only scan for the priority system control channel if the priority system is in the
WA Scan list.
9.9.5 When ProScan Is Enabled
The radio monitors the priority system and will switch to the priority system if the priority system meets
the criteria defined in the “ProSound/ProScan Options” dialog box. If ProScan is enabled, the rate at
which the radio will scan for the priority system is defined by the System Sample Time control.
9.9.6 Menu Selection
Press MENU and then use the
ramp control to scroll through the selections until SYS SCAN is
displayed. Then press MENU to toggle the System Scan state. The SYSC ON or SYSC OFF display
message is displayed for two seconds to show the new state.
9.9.7 Pre-Programmed Keypad Key
Press the pre-programmed key and the SYSC ON or SYSC OFF display message is displayed for two
seconds to show the new state.
9.10 GROUP SCAN OPERATION
Only Groups that are part of the radio's scan list will be scanned. Groups are added to the scan list on a
per system basis through programming, the radio keypad, or both, dependent upon programming. This
scan list can be changed by the user from the keypad unless programmed otherwise. Each system's group
scan list is retained in memory when the radio is turned off. The M7200 Series mobile radio can also be
64
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
programmed to provide Trunked Priority Group Scan capability, which operates similar to priority scan in
Conventional mode.
The following is a description of programmable scan features that should be helpful in understanding the
Group Scan Operation of the radio:
Scan Hang Time - the delay time the radio waits before resuming scan after the push-to-talk is released
or after the carrier has dropped a channel.
TX Select - the group the radio will transmit on while scanning. The radio is programmed to transmit on
either the scanned group or the selected group.
Scan List (privileges) - this feature allows or prohibits scan list changes by the user.
P1 Programming - priority group programming is accomplished by one (and only one) of three methods:
•
From the keypad, where the Priority programming is not fixed and does not follow the selected
channel,
•
•
Priority 1 group programming follows the selected channel, or
Priority 1 group programming is fixed during PC programming and cannot be changed by the user.
P1 Always Scan - determines if the Priority 1 Group will always be scanned, regardless of the scan state
set by the user.
9.10.1 Adding Groups to a Scan List
1. With scan operation turned off, select the desired group to add to the selected Trunked system group
scan list.
2. Press (+) or (-) with
to display the current priority status of the group on line 1 for a time-out
period.
3. While the status is displayed, press (+) with
to add the group to the scan list.
is displayed.
4. Press (+) with
a second time to set the group to Priority 2. is displayed.
5. Press (+) with
a third time to set the group to Priority 1.
is displayed in column 1, line 1.
The priority level selection sequence only advances the group to next higher priority level and stops
at priority level 1. To select a lower priority level, the group must be deleted from the scan list and
then added back to the scan list. Each new group added to the scan list starts at the lowest priority. If
the Priority 1 and Priority 2 groups are already set and a new group is assigned as Priority 1 or
Priority 2, the previously assigned group will change to non-priority scanning.
9.10.2 Deleting Groups from a Scan List
1. With scan operation turned off, select the desired group to delete from the selected trunked system's
group scan list.
2. Press (+) or (-) with
. The current scan status of the group is displayed for a time-out period.
3. Press (-) with
to delete the group from the scan list. or turns off. Any group that is
not in a trunked system group scan list will show a “blank” when it is the selected channel.
,
65
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
9.10.3 Nuisance Delete
A group can also be deleted from the scan list, if it is not the currently selected group by pressing (-) with
during scan operation while the radio is displaying the unwanted group. The group will be deleted
from the system's group scan list in the same manner as if done using the steps above. Deletions
performed in this manner will not remain deleted if the radio is turned off and then back on.
9.10.4 Turning Scan On
1. Toggle scan operation by pressing SCAN. The SCAN indicator turns on when the radio is scanning.
The SCAN key light blinks when temporarily disabled. Scanning will stop while
microphone is off-hook if the hookswitch feature is enabled through programming.
2. When a group on the scan list receives a channel assignment, the radio unmutes on the assigned
channel, the BSY indicator comes on and the received scan group is displayed.
•
•
The radio will continue scanning if a new group is selected when scan is on.
Pressing the PTT button when scan is on will cause the radio to transmit on the displayed group
or on the currently selected group depending on programming.
•
Pressing up with
when scan is on will cause the radio to recall the scanned group that was
last received. This group is recalled for a period equal to the scan hang time.
9.10.5 Priority Group Scanning
When scan is enabled and the Priority 1 and Priority 2 groups have been identified, the radio will listen to
calls on those groups and the selected group. While receiving a scanned group call, the radio will continue
to monitor the selected Priority 1 and Priority 2 groups and will drop the call if the selected group or other
higher priority call becomes active. During a Priority 2 call the radio will continue to monitor for a
Priority 1 group call.
The radio will monitor for Agency and Fleet calls that correspond to the Agency and Fleet associated with
the Priority 1 and Priority 2 groups. Priority Agency and Fleet calls will be indicated by displaying
AGENCY or FLEET on the System line of the display and associated Priority 1 or 2 group on the Group
line of the display.
9.10.6 Turning Scan Off
Toggle scan operation off by pressing SCAN. The radio will resume operation on the selected group.
9.11 INDIVIDUAL CALLS
9.11.1 Receiving and Responding to an Individual Call
When the radio receives an individual call (a call directed only to the user's radio), it unmutes on the
assigned working channel and turns on the BSY indicator. Line 1 shows “ID” followed by the logical ID
number of the radio sending the message, or the associated name if the ID number is found in the
individual call list. The individual call indicator will display *INDV* on line 2. The radio can be
66
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
programmed to ring when an individual call is received. If enabled, the ring begins five seconds after the
caller unkeys and will continue until the PTT button, the CLR button, or IND is pressed.
Hookswitch functions the same as CLR key in I-CALL, phone call, and menu modes.
If a response is made to the call prior to the programmed call-back time-out, the call will automatically be
directed to the originating unit. If a response is not made before the call-back time-out, the radio will
return to normal receive mode, but * WHC * will be displayed. If the caller's ID is not received,
UNKNOWN will display for the duration of the call and there will be no call-back hang time.
To respond after the call-back time-out, press the IND key. The radio's display will show the callers ID on
the first line and WHCI=1 on the second line. Pressing the PTT button at this point will initiate an
individual call back to the original caller. (If the last call was a group call, the display will show
WHCG=1. Pressing the PTT button will place the call as an individual call.)
The radio stores the IDs of the last 10 callers in the Calls Received List as shown. Individual calls are
stored in the top half of the list (1-10) and group calls are stored in the bottom half of the list (1-10). The
most recent call is stored in position 1, the second most recent call is stored in position 2, etc.
To access the list, press the IND key twice. Use
to scroll through the list. Press the MENU key to
display the time elapsed since the call was received.
9.11.2 Call Storage Lists
There are two lists available for call storage in the radio, the calls received list (1-10) and the personality
list (1-99 as defined by the user). When the individual call mode is entered by pressing IND, the calls
received list is available. The user can toggle to the personality list by selecting any key other than DIS or
toggle between the two lists by pressing the IND key. If wrap is enabled, the calls received list wraps on
itself and not into the other list.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
The saved call list shows all ten storage locations. If no calls have been received, the saved call list will be
empty and the pre-stored list will be available upon entering the individual call mode.
When in the saved call list, pressing MENU toggles the time stamp ON and OFF. The time stamp
indicates how long ago the call was received. The display indicates this information as HH:MM:SS where
HH = hours, MM = minutes and SS = seconds.
When in the pre-stored list, pressing MENU toggles the Logical IDentification (LID) on and off.
9.11.3 Sending an Individual Call
The following procedures describe how to initiate and complete an individual call.
1. To select a previously stored individual, select the I-Call mode from the menu or press IND followed
by the
ramp control to scroll through the list of stored individuals. The selection mode rules
apply. While in the individual call list, the menu key will toggle the display between the call name
and the unit ID number. If the individual is not stored in this list but the individual’s unit ID is known,
it can be entered directly from the keypad.
2. Press the PTT button; the radio performs the necessary signaling to obtain a communication channel.
When the signaling is complete and the radio is clear to transmit, TX indicator turns ON and the
channel access tone sounds. Line 1 shows the called individual's name if found in the list of stored
individuals or ID followed by the logical ID number of the unit being called. The message *INDV*
displays on line 2. Proceed with the message.
9.12 SCAT OPERATION
A SCAT™ (Single Channel Autonomous Trunking) System operates with the same set of features as a
standard EDACS system. The only significant user change relates to the BSY indicator. Since only one
channel, operating as both control and working channel, exists in a SCAT System, the BSY indicator will
be ON when the SCAT channel is in the working channel mode. When the transmission on the channel is
completed, the indicator turns OFF and indicates the return of SCAT control channel signaling.
9.13 TELEPHONE INTERCONNECT CALLS
9.13.1 Receiving a Telephone Interconnect Call (Trunked Mode Only)
Receiving a telephone interconnect call is identical to receiving an individual call. See the DTMF
Overdial Operation section if access to services requiring "over-dial" is needed. Overdial operations are
available for any special call whether it is an individual call or a telephone interconnect call.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
9.13.2 Sending a Telephone Interconnect Call (Trunked Mode Only)
Use the following procedures to initiate and complete a Telephone Interconnect call:
1. To select a previously stored phone number, select phone call mode from the menu, press PHN and
use the
ramp control to scroll through the list of stored phone numbers. The selection mode
rules apply. While in the phone call list, the MENU key will toggle the display between the phone
call name and the phone call number. If the phone number is not stored in this list but the phone
number is known, it can be entered directly from the keypad. If necessary, a pause can be entered by
pressing and holding 0-9, *, or # until an underscore appears in the display.
2. Press and release the PTT button; the radio performs the necessary signaling to obtain a
communication channel. When the signaling is complete and the radio is clear to transmit, TX
indicator turns on and the channel access tone sounds. Line 1 shows the accompanying name if
selected from the list of stored numbers or the phone number if entered directly. The message
*PHONE* is displayed on line 2. The radio then automatically transmits the programmed number
stored in the special call queue.
3. Telephone ringing will be heard. When someone answers the phone, press the PTT button and speak
into the microphone. Release the PTT button to listen to the caller. Unsuccessful interconnect
signaling returns the radio to the normal receive mode and the number remains displayed until the
special call is cleared by pressing the CLR button or the time-out expires or another group or system
is selected.
4. To terminate the call, momentarily press the CLR button.
The M7200 Series mobile radio is capable of half-duplex conversation only. The
caller’s message can only be sent if the PTT button is pressed (the radio is
transmitting) and the caller can only be heard by the person being called when the PTT
is released (the radio is receiving).
9.13.3 DTMF Overdial/Conventional Mode Telephone Interconnect
Once the radio has established a connection to the public telephone system, it may be necessary to "over-
dial" more digits to access banking services, answering machines, credit card calls or other types of
systems that require DTMF (Dual-Tone Multi-Frequency) access digits. Overdial operation can also be
used to initiate a telephone interconnect call via DTMF signaling if a dial tone has already been accessed
on the system. This is the method that is used for making a telephone interconnect call while operating in
the conventional mode but will also function in trunked mode if a dial tone is directly accessible.
Telephone numbers and other number sequences for overdialing can be stored in the phone list when
programming the radio or stored by the operator in the first ten phone list entries. These numbers are
accessed by pressing PHN then following the selection mode rules.
The following steps are required to dial these numbers:
1. Follow the procedure in Sending a Telephone Interconnect Call (Trunked Mode Only) to
establish a connection to the telephone system or consult the system administrator for the procedure
to access a dial tone on the trunked or conventional system.
2. Overdial numbers are transmitted using either method as follows:
69
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
METHOD 1: Press and hold PTT while entering the overdial number sequence from the keypad.
This method sends DTMF tones during individual, telephone interconnect, trunked
group, or conventional channel calls. Anytime the PTT button is pressed and held,
the keypad is enabled for DTMF entry.
METHOD 2: Press PHN to enter the overdial select/entry mode and follow the selection mode
rules to call up a stored number from the phone list or to directly enter the overdial
digits. Press PTT to send the overdial sequence once. If the number needs to be
transmitted again it must be selected or entered again (this prevents unwanted
numbers from being sent the next time the PTT button is pressed during the call).
This overdial select/entry mode remains active until the call is dropped, cleared, or MENU is pressed. The
overdial select/entry mode can be re-entered if the call is still active by pressing PHN.
9.13.4 Programmable Entries
Individual call ID numbers, telephone numbers and other number sequences for overdialing are stored in
the special call lists when programming the radio. The first ten entry locations of these lists can be
changed by the radio operator. The keypad is used when adding, changing and storing numbers in these
entry locations.
Use the following procedure to store a number in one of the first ten entries of a special call list:
1. Press IND or PHN to enter the individual call list or the phone call list. The selection mode rules
apply.
2. Scroll through the list using the
ramp control until one of the first ten entries is reached. NO
ENTRY is displayed if the location is empty.
3. Enter the desired number. If necessary, a pause can be entered by pressing and holding 0-9, (*), or (#)
until an underscore appears in the display. The individual call list entries will accept up to 5 digits.
The phone call list entries accept a combination of up to 31 digits and pauses.
4. Press and hold MENU until the display changes indicating that the number has been stored.
5. Repeat the steps above if the number stored in an entry location needs to be changed.
9.14 MOBILE DATA
The M7200 Series mobile radios, when operating in the EDACS configuration, permit either voice or data
calls to be transmitted or received. The radio can handle only one type of call at a time; however,
selection of either data or voice is selected transparently by the operator through normal usage of the
radio. Data communications is not supported in the conventional mode.
The mobile radios can be connected to Mobile Data Terminals (MDT) or to a host computer. Any RS-232
compatible device that supports the Radio Data Interface (RDI) protocol (Version 1.91 or greater) can be
connected to the mobile radio. Support for MDTs or host computers is a programmable option per radio.
Additionally, radios programmed for host computers can also be programmed for data only operation (no
voice calls transmitted or received).
Turn power to the radio OFF before connecting or disconnecting any cables, including
the data cable. Also, turn power to the radio OFF when docking or undocking a
connected laptop computer. Failure to turn the power OFF can damage the radio,
requiring service by a M/A-COM approved service center.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
9.14.1 Displays
The following will be displayed on the control unit during the various states of data mode of operation.
TX DATA
Displayed on bottom line of display when the radio is transmitting a data call.
RX DATA Displayed on bottom line of display when the radio is receiving a data call.
DATA OFF Displayed on top line of display when the radio is in the data disabled state.
DATA ON Displayed for two seconds on top line of display when the radio is toggled to the data
enabled state.
9.14.2 DATA OFF Operation
The radio can be placed in the data disable state by any of the following methods. When the data state is
disabled, the control unit displays "DATA OFF" on the top line. An ongoing data call is allowed to
complete except when an emergency is declared.
•
•
•
•
Removing the microphone from the hookswitch (hookswitch option must be enabled by pre-
programming).
Declaring an emergency (not to be used unless an actual emergency condition exists). Alert tone will
sound.
Pressing the OPT button (System Model) or OPTION (Scan Model) (pre-programmed). Alert tone
will sound.
Selecting the function using the MENU button (pre-programmed).
9.14.3 DATA ON Operation
The data state is enabled by one of the following (depending on how it was disabled). “DATA ON” will
be displayed top line of display for 2 seconds then the display returns to normal.
•
•
Replacing the microphone into the hookswitch (going on-hook). Only valid if the “DATA OFF”
operation was entered by removing the microphone from the hookswitch (going off-hook).
Clearing an emergency, but valid only if an emergency caused “DATA OFF” operation.
9.14.4 Exiting Data Calls
Under normal conditions, the radio enters the scan lockout mode and returns to the control channel after
completion of a data call (transmit or receive). If, during a data call, one of the following conditions
occurs, the data call is immediately terminated and the radio performs the desired function:
•
•
•
•
The PTT is activated.
The PTT is in Public Address mode.
An emergency is declared by pressing the pre-programmed emergency button.
A group or system change is made.
9.14.5 Scan Lockout Mode
Following the transmission or reception of a data call, if scan is enabled, scanning will stop temporarily
(duration pre-programmed). During this time the scan LED will flash to indicate that scan is enabled but
71
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
temporarily suspended. This mode is normally exited when the pre-programmed time expires; however,
the following actions will terminate the scan lockout mode before the timeout is completed.
•
•
•
•
•
•
•
•
•
•
•
•
The CLR (System Model) or CLEAR (Scan Model) button is pressed.
The PTT is pressed.
A group or system change is made.
Enter phone call mode.
Enter individual call mode.
A new emergency assignment has been received.
The PTT is pressed in Public Address Mode.
An emergency is declared or cleared.
Microphone is removed from hookswitch (off-hook).
Receiving an individual or phone call.
Receiving an Agency, Fleet or System All Call.
Pressing the SCAN button to turn scan on or off.
9.14.6 Data Lockout Mode
The data lockout mode is a pre-programmed mode when the radio will not respond to any data channel
assignments and prevents receive data calls from interrupting voice calls. Transmit data calls will still be
initiated when needed by the operator. After a pre-programmed time, the radio will respond to receive
data calls; however, the following conditions will clear the data lockout mode:
•
•
•
•
•
•
The CLR (System Model) or CLEAR (Scan Model) button is pressed.
Transmitting a data call.
Changing a system.
An emergency is declared.
Pressing the PTT while in Public Address mode.
Turning scan ON with the SCAN button.
9.15 STATUS/MESSAGE OPERATION
Status and message operation is possible with either the Scan or System version of the M7200 Series
mobile radio unit. The following procedure is applicable for the System version. For operation with the
Scan version, the four primary keycaps must be reconfigured and pre-programmed for status/message
operation.
9.15.1 Status Operation
Status operation permits the transmission of a pre-programmed status condition to the EDACS site.
To send a status condition, press the STS button (keylight comes on) then press one of the number
buttons (0-9) to select the pre-programmed status. If no status has been programmed for the selected
number button, the radio will display NO ENTRY and the radio will sound a low tone. A valid selection
will permit the status text to appear in the display for a pre-programmed time. After the time-out expires
72
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
or the MENU button has been pressed (the MENU button will override the time-out period), the status is
selected and will be transmitted to the site or stored in the radio memory where it can be polled by the site
at a future time. If the site receives the status properly, when transmitted or polled by the site, a high-
pitched tone sounds and the keylight associated with that status will remain lit. If the site does not receive
the status properly, a low-pitched tone sounds and the keylight associated with the status will blink.
If an incorrect status was selected or the incorrect number button was pressed, the status can be changed
during the pre-programmed time-out period by pressing another number button. The status selection can
also be cancelled by pressing the CLR button prior to the time-out period.
To view the currently selected status after it has been transmitted, press the STS button. If the status was
not sent successfully to the site, the text associated with the status will flash in the display.
The radio can also be pre-programmed to redesignate the keypad buttons for ST0 thru ST9 to send status
condition. In this configuration the radio status operation will operate as previously described except the
STS button is not required. The keylight associated with ST0 thru ST9 will indicate which status is
selected.
9.15.2 Message Operation
Message operation permits the transmission of a pre-programmed message text to an EDACS site.
To send a message, press the MSG button (keylight comes on) then press one of the number buttons (0-9)
to select the pre-programmed message text. If no message text has been programmed for the selected
number button, the radio will display NO ENTRY and a low-pitched tone sounds. A valid selection will
permit the message text to appear in the display for a pre-programmed time. After the time-out expires or
the MENU button has been pressed (the MENU button will override the time-out period), the message
text is selected and will be transmitted to the site. If the site receives the message properly when
transmitted, a high pitched tone sounds and the MSG keylight remains lit. If the site does not receive the
message properly, a low-pitched tone sounds and the MSG keylight will blink.
If an incorrect message text was selected or the incorrect number button was pressed, the message text
can be changed during the pre-programmed time-out period by pressing another number button. The
message text selection can also be cancelled by pressing the CLR button prior to the time-out period.
To view the currently selected message text after it has been transmitted, press the MSG button and then
the CLR button prior to the time-out period. If the message text was not sent successfully to the site, the
text associated with the message will flash in the display.
9.16 EDACS CONVENTIONAL P1 SCAN
This feature permits the radio user to scan a pre-programmed conventional system and channel as a
Priority 1 (P1) channel while the radio is selected for EDACS trunked system. If activity is detected on
the conventional P1 channel, the radio will unmute and remain on this conventional channel for the
programmable hang time.
The radio must be pre-programmed to designate a button for scan ON/OFF operation.
9.17 DYNAMIC REGROUP OPERATION
Dynamic regroup operation permits multiple talk groups (up to eight) to be added to a radio via the
Communications Systems Director (CSD). The radio must be pre-programmed to respond to regrouping.
Dynamic regrouping will not be activated in a radio until an activation message is sent by the system
manager. Each radio that receives and acknowledges regrouping instructions is successfully regrouped.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
Pressing and holding the CLEAR (Scan Model) or CLR (System Model) button for 2.5 seconds toggles
the user into and out of the dynamic regroup group set. A double beep will sound for entry or exit. The
display will indicate REGR_0x where "x" is a digit of 1 to 8 indicating the group when dynamic regroup
has been enabled by the user. If the radio is in dynamic regroup and the user selects a group that has not
been regrouped, the display will show NO ENTRY. The radio will be prevented from transmitting and
receiving calls in this condition except for scanned groups.
9.17.1 Emergency Operation
If the pre-programmed group set on the currently selected system contains an EMER/HOME group and
the radio is in dynamic regroup, the radio will exit dynamic regroup and declare the emergency on the
HOME group. If no EMER/HOME group is present, the radio will declare the emergency on the currently
selected dynamic regroup group.
9.18 PAGE (P25 TRUNKED ONLY)
Page sends a PING message to a radio and functions similar to Individual Call.
The following procedures describe how to initiate and complete a Page.
1. To select a previously stored individual, select the Page mode from the menu followed by the
ramp control to scroll through the list of stored individuals. The selection mode rules apply. While in
the individual call list, the menu key toggles the display between the call name and the unit ID
number. On System model radios, the individual’s unit ID can also be entered directly from the
keypad.
2. Press the PTT button; the radio performs the necessary signaling on the control channel. On the
calling radio, line 1 shows the called individual's name if found in the list of stored individuals or ID
followed by the logical ID number of the unit being called. If the receiving radio receives the Page
and responds, both radios will emit three high-pitched tones. The receiving radio will also display
PAGE and the ID of the calling radio.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
10 CONVENTIONAL OPERATION
10.1 RADIO STATUS ICONS
Status icons are indicators that show the various operating characteristics of the radio. The icons appear
on the first line of the display.
Figure 10-1: Typical Display
Table 10-1: Icons and Descriptions
ICON
DESCRIPTION
Indicates selected group or channel is in scan list.
Indicates selected group or channel is programmed as Priority 1 in scan list.
Indicates selected group or channel is programmed as Priority 2 in scan list.
Indicates a conventional channel enabled with Channel Guard Function.
Indicates the current channel is set up as an analog channel.
Volume bars – indicates relative volume level.
Scan mode enabled.
10.2 MESSAGES
During radio operation, various messages are displayed on either line 1 or line 2. Typical messages
include control channel status information, such as system busy or call denied, or messages associated
with the radio's operation, (i.e. volume adjust). These messages are described as follows:
Table 10-2: Display Messages
MESSAGE
NAME
DESCRIPTION
TALKARND
VOL=31
Talk-around
Indicates the radio is operating on conventional channels in talk-around mode (no repeater).
Volume Level
Indicates the current volume level. The volume level display ranges from OFF (silent) to 31
(loudest).
UNKNOWN
Caller's ID Not
Received
Indicates that an individual call is being received, but the caller's ID was not received.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
MESSAGE
NAME
DESCRIPTION
T99 ON
Type 99 Decode ON
Type 99 Decode OFF
Public Address ON
Public Address OFF
Indicates the Type 99 Decode feature is enabled.
T99 OFF
PA ON
Indicates the Type 99 Decode feature is disabled.
Indicates that the public address function of the radio is enabled.
Momentary (2 seconds) indicates that public address function of the radio was disabled.
PA OFF
ALRM ON
ALRM OFF
External Alarm Enabled Indicates that the external alarm function of the radio is enabled.
External Alarm
Disabled
Momentary (2 seconds) indicates that the external alarm function of the radio was disabled.
NO KEY #
Encryption Key Missing Flashing indicator indicates that no encryption key or an incorrect encryption key is
programmed into the radio.
BCKL=1-6
GR
Backlight
Group ID
Indicates the display intensity and keypad backlight level.
Indicates that the call is a group call and is followed by the GID of the caller.
MENU
Displayed when the menu key is pressed and remains displayed in line 1 until a menu item is
selected.
SYS=1-64
SEL PHN
Ggg-v.vv
System = 1 - 64
Select Phone
The system number for the current base station of the system displayed in line 1. It is displayed
in line 2 of the display. Press the system key to obtain this display.
After pressing the PHN key, selecting an entry from the phone list by typing the entry number
will display this message on Line 1.
Code Group and
Revision Number
This is code group and revision number that is displayed in line 2 when the menu item
“REVISION” is selected. The ‘gg’ is the group number of the software. The first ‘v’ is the
hardware version and ‘vv’ is the revision of the software.
NO ENTRY
Indicates that there is no data stored in one of the programmable items in either the phone list
or individual call list. The user programmable items are items 1 through 10 in each list.
INV SYS
Invalid System
Displayed when the current system is an invalid type.
CHN=1-99
Channel = 1 - 99
Displayed on line 1 of the display. This is a conventional channel index displayed when the
group key is pressed.
FIX LIST
FIXED P1
(c) 2004
Fixed List
The Priority scan list is fixed and cannot be changed using the add or delete keys.
The Priority 1 scan channel is fixed and cannot be changed using the add or delete keys.
Fixed Priority 1
Displayed in line 2 when the message ‘M/A-COM’ is displayed in line 1 while displaying
different items under the menu when “REVISION” is selected by the operator.
EM
Emergency
Indicates an emergency has been declared by the LID that follows the display, “EM.” An
example of this is “EM 01201.”
*INDV*
*GROUP*
Individual Call
Group Call
Displayed in line 2 of the display when an individual call is in progress (trunked and T99
modes only).
Indicates a group call is in progress and is displayed on line 1 of the display (trunked and T99
modes only).
SPKR ON
SPKR OFF
BANK=1-8
External Speaker ON
External Speaker OFF
Displayed when the external speaker is enabled.
Displayed when the external speaker is disabled.
The bank of keys that are going to be loaded when the keyloader loads encryption keys. This is
only valid for radios that support VGS, VGE, or DES encryption. It is displayed on line 2 of
the display when the encryption keyloader is connected.
KEY LOAD
KEY ZERO
Displayed on line 1 of the display when the encryption keyloader is connected.
Displayed on line
2
of the display when the reset and option buttons are pressed
simultaneously for approximately two seconds. The encryption keys are zeroed.
SYS KEY
KEY=1-7
System Key
Displayed on line 1 of the display in the display key mode of the menu. It is followed in the
second line with a key number “KEY = <1..7>”.
Displayed on line 2 of the display in the display key mode of the menu for conventional
systems when the “SYS KEY” or “CHN KEY” is displayed in line 1 and for trunked systems
when the “SYS KEY” or “GRP KEY” is displayed in line 1.
PRIMARY
Displayed on line 1 of the display when the primary keys are enabled.
PRS NAME
Personality Name
Displayed on line 1 of the display under the revision selection of the menu. The personality
name is displayed on line 2 at the same time.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
MESSAGE
NAME
DESCRIPTION
M/A-COM
Displayed on line 1 of the display under the revision selection of the menu. The copyright year
is shown in line 2 of display at the same time “(c) 2007.”
10.3 ALERT TONES
The M7200 series mobile radio provides audible alert tones or “beeps” to indicate the various operating
conditions. These alert tones can be enabled or disabled through programming.
Table 10-3: M7200 EDACS Mode Alert Tones
NAME
TONE
DESCRIPTION
Sounds after keying the radio (Push-To-Talk button is
pressed). Indicates the radio has been assigned a
working channel
Call Originate
A short mid-pitched tone.
Sounds if the programmed time for continuous
transmission is exceeded. The transmitter will shut down
shortly after the alert, interrupting communications.
Release and re-key the PTT button to maintain
communications. This will reset the carrier control timer
and turn the transmitter back on.
Five
short
high-pitched
Carrier Control Timer
warning tones followed by a
long low-pitched tone.
Indicates a key has been pressed. A short low-pitched
tone indicates no action was taken because the key is
not active in the current mode.
Key Press Alert
A short tone.
10.4 MENU
The menu function accesses features that are not available directly from the keypad. The order and
specific number of menu items available is configurable through programming. Upon radio power up, the
menu item at the beginning of the menu list will always be displayed first. Subsequent access to the menu
function will return the last menu item that was shown in the display. To enter the menu mode, press
MENU. The
ramp control, MENU, and CLR are used during the selection process. All of the
selection mode rules previously detailed apply to the menu item selection process with the exception of
direct access. The radio will continue to receive and transmit normally while in the menu function.
A new item is displayed by using the
ramp control to scroll through the list in increasing and
decreasing order. The displayed menu item is made active by pressing MENU.
After entering the menu selection mode, the following generic display format will appear.
M E N U
Y Y Y Y Y Y Y Y
Line 1 indicates the radio is in the menu selection mode. Line 2 indicates the menu item (YYYYYYYY)
that is to be viewed or changed (some menu items provide radio information and do not have changeable
parameters).
An example of the menu item selection process and menu item parameter change is detailed below for the
contrast menu item.
1. Press MENU to enter the menu mode.
2. Press the
ramp control until the display shows:
77
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
M E N U
CONTRAST
3. Press MENU. The contrast menu item is activated and the display will be similar to the following:
CNTRST = X
Y Y Y Y Y Y Y Y
Line 1 shows the active menu item and its current parameter setting (XXX). Line 2 shows the
currently selected system or group name (YYYYYYYY).
4. The menu item's parameter setting shown in the display can now be changed by using the
ramp control to scroll through the list of parameter values. Once the desired setting is reached, press
MENU to store the value and return to the normal display. For menu items that display radio
information, use
to scroll through a list of informational displays. The menu items are listed in
Table 10-4: Menu Item Information
PARAMETER
SETTINGS
FEATURE
DISPLAY
Menu Item:
COMMENT
CONTRAST
Once selected:
CNTRST=
Contrast Adjust
1, 2, 3, 4, 5, 6, 7, 8
Selects the Contrast level.
Informational
Radio Revision
Information
Menu item:
REVISION
displays only
(see radio); no user
selectable settings.
Selects the information display to view.
Allows access to the Phone Call Feature.
Menu item:
PHN CALL
Once selected: See
Telephone Interconnect
Call Section
Phone Call
Menu Item: EXTALARM
Once Selected:
EXTALARM
EXTALARM replaces the system name on the
display as long as the external alarm feature is
enabled.
External Alarm
ON, OFF
ON, OFF
Menu item:
PUB ADDR
Once selected:
PA ON or
Public
Address
Public Address is toggled ON and OFF.
External Speaker is toggled ON and OFF.
PA OFF
Menu item:
EXT SPKR
External Speaker Once selected:
ON, OFF
SPKR ON or
SPKR OFF
Menu item: KEYLOAD
Once selected:
KEY LOAD BANK = N
Encryption Key
Loading
Enables the radio to accept the loading of encryption
keys.
Up to 8 banks of 7 keys
Menu item: DISP KEY
Once selected:
SYS KEY, GRP KEY or
CHN KEY and KEY = N
Display Current
Encryption
Key(s)
Displays current encryption key number.
Menu item:
Front Panel
Squelch Adjust
SQUELCH
Once selected:
SQLCH=xx
1-16
Allows setting of squelch.
Scan
Menu item: SCAN
ON, OFF
Toggles scan function ON or OFF.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
PARAMETER
SETTINGS
FEATURE
DISPLAY
COMMENT
Menu item: SCAN ADD
Scan Add
Once selected: Proper scan S, 2 or 1
icon displayed.
Adds group or channel to scan list.
Menu item: SCAN DEL
Once selected: Scan icon
goes out.
Scan Delete
Deletes group or channel from scan list.
Menu item: SCAN A/D
Scan Add/Delete When selected: Toggles
through scan selections
Toggle sequence
S, 2, 1, S, ...
Changes present group or channel to next scan
choice in scan list.
Menu Item: SCAN ADD
Press twice when actively
Last Scanned
Changes the selected channel to the last scanned
channel.
receiving; three times when
Channel Recall
not receiving. Scan icon
displayed.
Menu item: HOME
Home channel
Changes to the group or channel defined for Home
function.
Once selected: Home group
selection
or channel displayed.
Menu item: SYS SEL
System select
1-64 = (n)umber of desired
system
Displays the system selected.
Once selected: SYS = n
External alarm #2 Menu item: EXTALRM2
ON, OFF
Toggles external alarm #2 feature ON or OFF.
Menu item: SYSGRP 1
Menu item: SYSGRP 2
System selection Menu item: SYSGRP 3
Menu item: SYSGRP 4
Changes to the System & Group/Channel
programmed for SYSGRP 1-5.
Menu item: SYSGRP 5
Toggles the mute function ON or OFF to control the
audio output from the selected radio.
Mute
Menu item: MUTE
Menu item: MUTE 1
Menu item: MUTE 2
Menu item: RADIO
ON, OFF
ON, OFF
ON, OFF
ON, OFF
Toggles the mute 1 function ON or OFF on radio
#1.
Mute #1
Mute #2
Toggles the mute 2 function ON or OFF on radio
#2.
Multiple radio
operation
Toggles the currently selected radio.
Menu item: RADIO 1
ON, OFF
ON, OFF
Changes to radio #1.
Changes to radio #2.
Radio selection
Menu item: RADIO 2
Menu item: TALKARND
Once selected:
TALKARND on line 1
Talkaround
feature
Toggles talkaround ON or OFF (transmit frequency
changed to receive frequency).
ON, OFF
Menu item: CHN SEL
Once selected: CHN = n
1-99 = (n)umber of desired
channel
Channel selection
Displays the conventional channel selected.
Menu Item: FEATURES
Once selected:
See Feature Encryption
Display section
Indicates current features program- med into the
Informational displays only; radio as well as certain information required to add
Feature
Encryption
Display
no user selectable settings
ON, OFF
features to the radio (refer to the Table of Contents
for Feature Encryption Display.
Menu Item: T99 ENAB
Once selected:
T99 ON or T99 OFF
Type 99 Decode
Enable
Type 99 Decode is toggled ON and OFF.
Menu Item: SYS SCAN
Once selected: SYSC ON ON, OFF
or SYSC OFF
System Scan
Enable
System Scan features like ProScan are toggled ON
and OFF.
10.5 RECEIVING A CALL
1. Turn the radio on by rotating the POWER ON-OFF/VOLUME knob clockwise (out of detent). A
short alert signal (if enabled through programming) indicates the radio is ready to use.
2. Adjust the POWER ON-OFF/VOLUME knob to the desired volume level.
3. Select the desired conventional system and channel. The display indicates the current conventional
system and channel names.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
4. The radio is now ready to receive calls.
5. When the radio receives a call (and the correct encoding is decoded, if programmed and enabled), it
unmutes on the channel and the BSY indicator comes on.
10.6 SENDING A CALL
1. Turn ON the radio and set the POWER ON-OFF/VOLUME knob to the desired volume level.
Select the desired conventional system and channel.
2. Ensure that the channel is not busy by pressing the CLR button to briefly disable any channel
decoding and unmute the receiver or observe the unlit BSY indicator. If the Channel Busy Lockout
feature is programmed for the selected channel, the radio will not transmit when the channel is busy.
3. Press and hold the PTT button. The TX indicator will turn on and a short beep sounds (if
programmed) indicating that communication can begin.
4. Hold the microphone approximately three inches from the mouth and speak in a normal voice.
5. Release the PTT button when the transmission is complete and listen for a reply.
10.7 EMERGENCY OPERATION
If enabled, G-STAR emergency signaling can be transmitted when operating in the conventional mode.
This G-STAR signaling will transmit 5 times with a delay between each transmission. To send an
emergency call on the selected conventional system and channel (or on an optionally pre-programmed
conventional emergency system and channel), proceed as follows:
Press and hold the red Emergency button for approximately one second (this time is programmable and,
therefore, could be longer or shorter; check with the system administrator). The radio turns on the TX
indicator and proceeds to transmit the pre-programmed G-STAR emergency signaling sequence.
G-STAR is programmed to transmit in one of the following methods:
METHOD 1: G-STAR is transmitted on the selected channel. If the channel is changed the emergency
signaling will continue to be transmitted on the newly selected channel.
METHOD 2: Same as METHOD 1 but the radio will lock on to the currently selected channel. Any
attempts to change the system or channel will be disabled.
METHOD 3: G-STAR is transmitted on a pre-programmed conventional emergency system and
channel regardless of the selected channel. In this case the selected channel is available
for voice transmission and the radio will periodically change to the pre-programmed
emergency system and channel to send the emergency signaling and then change back to
the selected channel.
METHOD 4: Same as METHOD 3 but the radio will lock on to the pre-programmed emergency
system and channel. Any attempts to change the system or channel will be disabled.
The emergency state can be cleared by turning the radio OFF and then back ON.
10.7.1 Using 5-Tone Signaling to Declare an Emergency
If 5-Tone signaling is defined for emergency declaration in place of G-STAR emergency signaling, a pre-
programmed tone sequence will be transmitted instead of the G-STAR sequence. This emergency
declaration functions as the G-STAR emergency in all other respects.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
10.7.2 Tone Encode Transmission
In conventional mode, two keys can be defined to be tone encode triggers. If either one of the pre-
programmed tone encode triggers is pressed, a pre-programmed tone sequence will be transmitted on the
current system and channel. (See Section 10.7 if the emergency key is used.) The TX indicator will light
during tone transmission and a beep will sound at the end of the transmission. If enabled, audible side
tones will be heard in the radio speaker as well. If PTT is pre-programmed as one of the triggers, the
microphone will become active for voice communication after the tone sequence is complete.
Tone encode will be transmitted with Channel Guard if one is defined, and tones are always transmitted in
clear voice mode, even if the channel is set for digital or private (see VOICE MODES). Digital or private
voice transmission will resume normally after the tone transmission.
10.8 SCANNING CONVENTIONAL CHANNELS
Channels, which have been previously added to the scan list on a per system basis, can be scanned. The
selected channel is scanned (if enabled through programming) whether or not it is in the scan list. Each
conventional system's channel scan list is retained in memory when the radio is turned OFF.
The scan rate will vary depending upon the number of channels in the scan list and whether or not the
radio is programmed to scan for channels with decoding enabled. Fewer channels will result in a faster
scan rate. If programmed for dual-priority scan operation, the priority-one, priority-two and the remaining
scan list channels are scanned. Once a signal is detected and the correct encoded squelch signal is
decoded (if programmed), the radio receives the message and displays the received scan channel. At the
same time, scanning continues on the priority-one and priority-two channels. If a priority-one or priority-
two channel carrier, regardless of encoded squelch decoding, is detected while a non-priority channel is
being received, the display name is updated and the received channel is switched to the priority channel.
Scanning of the priority-one channel will continue if a message is being received on the priority-two
channel.
While receiving a call on a non-priority or a priority two channel, the radio periodically checks the
priority one and two channels. If Scan with Channel Guard is enabled, the radio will use Channel Guard
to decide whether to unmute on a priority channel. The radio will stop, on squelch detection, on a priority
channel. In normal operation, the radio will unmute only on detecting the correct Channel Guard;
otherwise, it will remain muted until the priority channel call and hang time have ended. An optional
feature allows the radio to continue scanning upon the detection of the wrong Channel Guard on a priority
channel. The user can then select the rate at which this channel is scanned until the call ends.
10.8.1 Adding Channels to a Scan List
1. With scan operation turned OFF, select the desired channel to add to the selected conventional system
channel scan list.
2. Press (+) or (-) with
to display the current scan status on line 1 of the display for a time-out
period.
3. While current scan status is displayed, press (+) to add the channel to the scan list.
is displayed.
This sets the selected channel for non-priority scanning.
4. Press (+) again to set the channel for Priority 2 (P2) scanning and
is displayed.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
5. A third press of (+) sets the channel for Priority 1 (P1) scanning and
is displayed on line 1. If the
P1 or P2 channels are already set and a new channel is then assigned as the P1 or P2 channel, the
previously assigned priority channel will change to non-priority scanning. The priority setting
selection sequence is set and stops at P1, therefore the channel must be deleted from the scan list by
pressing (-) before the channel is set to a previous priority setting. Any channel that is in a system's
channel scan list will show
,
, or
when it is the selected channel.
10.8.2 Deleting Channels From A Scan List
1. With scan operation turned OFF select the desired channel to delete from the selected conventional
system's channel scan list.
2. Press (+) or (-) with
. The current status is displayed for a time-out period. Press - with
, or will turn OFF.
to delete the channel from the scan list.
,
10.8.3 Nuisance Delete
A channel can also be deleted from the scan list, if it is not the currently selected channel, by pressing
down with twice during scan operation while the radio is displaying the unwanted channel. The
channel will be deleted from the conventional system's channel scan list in the same manner as if done
using the steps above. Deletions done in this manner will not remain deleted if the radio is turned OFF
and then back ON.
10.9 TURNING SCAN ON
1. Toggle the scan operation ON by pressing SCAN. The SCAN indicator will turn ON when the radio
is scanning.
Scanning will stop while the microphone is off-hook if the hookswitch feature is enabled
through programming.
2. When a channel on the scan list receives a channel assignment, the radio unmutes on the assigned
channel, BSY indicator comes ON and the received scan channel is displayed.
•
•
The radio will continue scanning if a new channel is selected when scan is ON.
Pressing the PTT button when scan is ON will cause the radio to transmit on the displayed
channel or to the currently selected channel depending on programming.
•
Pressing (+) with
when scan is ON causes the radio to recall the scanned channel that
was last received. This channel is recalled for a period equal to the scan hang time.
10.10TURNING SCAN OFF
Toggle the scan operation OFF by pressing SCAN. The radio will resume operation on the selected
channel.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
10.11SQUELCH ADJUST
In the conventional mode of operation, the squelch can be re-adjusted in the MENU selection mode or
from a front panel key on the keypad that has been pre-programmed. A default value of 9, or any user
level between 1 and 16, can be selected using programming software. The user can change this setting
either of two ways from the front panel keys.
A value of 16 requires a strong signal to open squelch, a value of 2 requires a very weak
signal to open squelch, and a value of 1 is open squelch.
When the squelch adjust feature is activated, Channel Guard, T99 decode, and Scan are
disabled. When the squelch adjust feature is exited, Channel Guard, T99 decode, and
Scan are restored to their previous states.
10.11.1
Menu Selection
1. Press the MENU key and then use the RAMP control
to scroll through the selections until
SQUELCH is displayed. Then press MENU (select) again.
2. The display will show SQLCH=xx, where "xx" is the value between 1 and 16.
3. Use the RAMP control
to scroll through the values. Then press the MENU (select) key to
save the new value after the display time-out (2 seconds). The displayed value will be selected and
saved.
4. If the MENU or CLR key is pressed before the time-out, the menu feature will exit and the squelch
level will not be updated. The original value will be restored.
10.11.2
Pre-Programmed Keypad Key
1. Press the pre-programmed key and the display will indicate SQLCH=xx, where "xx" is the value
between 1 and 16.
2. Use the RAMP control
to scroll through the values. Then press MENU to save the new value
or wait for the display time-out (2 seconds). The displayed value will be selected and saved.
3. If the CLR key is pressed before the time-out, the squelch level will not be updated and the original
value will be restored.
10.12TYPE 99 DECODE
If the Type 99 Decode Option has been pre-programmed, individual selective calling is possible. The
radio can now decode individual, group or supergroup paging calls. Two sets of Type 99 paging codes
must be pre-programmed into the radio. When the radio decodes an appropriate Type 99 code sequence,
an alert tone and visual indicator is provided to the user. The receiver then operates as a noise squelched
unit until Type 99 is reset. Type 99 decode continues to operate during this noise squelched period. The
appropriate Type 99 alert tone will sound again if it detects a valid two-tone sequence.
Type 99 operation can be reset manually or automatically (pre-programmed). Manual reset is achieved by
briefly pressing CLR, if programmed. Automatic reset, if enabled, occurs after a 30 second interval
following the most recent decode of a Type 99 tone sequence. Hookswitch (pre-programmed) can also
83
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
enable or disable Type 99 decode. The pre-programmed key light will blink when Type 99 is disabled by
the hookswitch.
Type 99 decode will continue to be active while the radio's CLR button is pressed. This allows the user to
monitor calls and still be alerted when a call is directed to the user. While the user continues to press
CLR, the user will hear both calls and all Type 99 tone signals. If CLR is pressed for longer than two (2)
seconds, Type 99 decode will either be disabled or re-enabled depending upon its present state.
To check the Type 99 enable status, press the Scan Add/Delete
of Type 99 decode will be displayed for a time-out period.
ramp control. The current status
If a Horn Alert Option is installed and enabled with the Type 99 Decode Option, the radio can beep the
vehicle horn when a Type 99 call is received. This option permits alerting persons out of the vehicle when
a call is received.
Type 99 is automatically disabled when Scan is enabled.
10.12.1
Menu Selection
Press MENU and then use the
ramp control to scroll through the selections until T99 ENAB is
displayed. Then press MENU to toggle the Type 99 decode state. The T99 ON or T99 OFF display
message is displayed for two seconds to show the new state.
10.12.2
Pre-Programmed Keypad Key
Press the pre-programmed key and the T99 ON or T99 OFF display message is displayed for two
seconds to show the new state.
10.13DIRECT MODE OPERATION
The direct mode (or talk-around) provides short range, line of sight communications. One of the buttons
on the control unit must be pre-programmed for this feature to function.
1. Make sure the radio is ON and then select the desired conventional system and channel.
2. Press the pre-programmed button to toggle the talk-around function ON.
3. Ensure that the channel is not busy by pressing the CLR (System version) or CLEAR (Scan version)
to briefly disable any channel decoding and unmute the receiver or observe the unlit BSY indicator. If
the Channel Busy Lockout feature is programmed for the selected channel, the radio will not transmit
when the channel is busy.
4. Press and hold the PTT button. The TX indicator will light and a short beep sounds (if pre-
programmed) indicating that communication can begin.
5. Release the PTT button when the transmission is complete and listen for a reply.
6. When the communications is completed, press the pre-programmed button to toggle the talk-around
function OFF.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
11 P25 CONVENTIONAL OPERATION
11.1 RADIO STATUS ICONS
Status icons are indicators that show the various operating characteristics of the radio. The icons appear
on the first line of the display.
Figure 11-1: Typical Display
Table 11-1: Icons and Descriptions
ICON
DESCRIPTION
Indicates selected group or channel is in scan list.
Indicates selected group or channel is programmed as Priority 1 in scan list.
Indicates selected group or channel is programmed as Priority 2 in scan list.
Indicates a conventional channel enabled with Channel Guard Function.
Transmitting or receiving in encrypted mode.
Indicates the current channel is set up as an analog channel.
Indicates the current channel is set up as a ProVoice channel.
Scan mode enabled.
Indicates the current channel is set up as a Project 25 (P25) channel.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
11.2 MESSAGES
During radio operation, various messages are displayed on either line 1 or line 2. Typical messages
include control channel status information, such as system busy or call denied, or messages associated
with the radio's operation, (i.e. volume adjust). These messages are described as follows:
Table 11-2: Display Messages
MESSAGE
NAME
DESCRIPTION
TALKARND
VOL=31
Talk-around
Indicates the radio is operating on conventional channels in talk-around mode (no repeater).
Volume Level
Indicates the current volume level. The volume level display ranges from OFF (silent) to 31
(loudest).
UNKNOWN
Caller's ID Not
Received
Indicates that an individual call is being received, but the caller's ID was not received.
T99 ON
Type 99 Decode ON
Type 99 Decode OFF
Public Address ON
Public Address OFF
Indicates the Type 99 Decode feature is enabled.
T99 OFF
PA ON
Indicates the Type 99 Decode feature is disabled.
Indicates that the public address function of the radio is enabled.
Momentary (2 seconds) indicates that public address function of the radio was disabled.
PA OFF
ALRM ON
ALRM OFF
External Alarm Enabled Indicates that the external alarm function of the radio is enabled.
External Alarm
Disabled
Momentary (2 seconds) indicates that the external alarm function of the radio was disabled.
PVT DIS
Private Mode Disabled
Indicates that private mode is disabled or no encryption key has been programmed for the
selected group/channel or special call.
FRCD PVT
NO KEY #
Forced Private
Operation
Indicates that forced private operation has been pre-programmed into radio.
Encryption Key Missing Flashing indicator indicates that no encryption key or an incorrect encryption key is
programmed into the radio.
BCKL=1-6
GR
Backlight
Indicates the display intensity and keypad backlight level.
Group ID
Indicates that the call is a group call and is followed by the GID of the caller.
WHC=1
Who Has Called
This display indicates the number from the Who Has Called list. Individual calls received but
not responded to are stored in a Who Has Called list. This list is accessible by pressing the #
key and then the INDV key after the Individual call has timed out or the Clear button is
pressed. This display is on line 2 and the LID of the caller is displayed on the top line.
Currently the list is not implemented and the display will always be WHC=1.
PHONE
Phone Call
Displayed when a phone call is received from the site. It is displayed in line 1 of the display.
Line 2 of the display will contain the display *INDV* when line 1 contains this message. The
radio interprets a received phone call as an individual call.
MENU
Displayed when the menu key is pressed and remains displayed in line 1 until a menu item is
selected.
SYS=1-64
INDV=1-99
PHN=1-99
SEL PHN
Ggg-v.vv
System = 1 - 64
Individual = 1 - 99
Phone = 1 - 99
Select Phone
The system number for the current base station of the system displayed in line 1. It is displayed
in line 2 of the display. Press the system key to obtain this display.
Indicates which item in the individual call list is being displayed. It is displayed in line 2 of the
display. The name or ID of the item in the list is displayed in line 1 of the display.
Indicates which item in the phone list is being displayed. It is displayed in line 2 of the display.
Line 1 of the display will be the last 3 characters of the list item contents.
After pressing the PHN key, selecting an entry from the phone list by typing the entry number
will display this message on Line 1.
Code Group and
Revision Number
This is code group and revision number that is displayed in line 2 when the menu item
“REVISION” is selected. The ‘gg’ is the group number of the software. The first ‘v’ is the
hardware version and ‘vv’ is the revision of the software.
*PHONE*
Phone Call
Displayed when an initiated phone call is in progress. This is displayed on line 2 of the display.
NO ENTRY
Indicates that there is no data stored in one of the programmable items in either the phone list
or individual call list. The user programmable items are items 1 through 10 in each list.
INV SYS
Invalid System
Displayed when the current system is an invalid type.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
MESSAGE
NAME
DESCRIPTION
CHN=1-99
Channel = 1 - 99
Displayed on line 1 of the display. This is a conventional channel index displayed when the
group key is pressed.
FIX LIST
FIXED P1
(c) 2004
Fixed List
The Priority scan list is fixed and cannot be changed using the add or delete keys.
The Priority 1 scan channel is fixed and cannot be changed using the add or delete keys.
Fixed Priority 1
Displayed in line 2 when the message ‘M/A-COM’ is displayed in line 1 while displaying
different items under the menu when “REVISION” is selected by the operator.
EM
Emergency
Indicates an emergency has been declared by the LID that follows the display, “EM.” An
example of this is “EM 01201.”
*INDV*
*GROUP*
Individual Call
Group Call
Displayed in line 2 of the display when an individual call is in progress (trunked and T99
modes only).
Indicates a group call is in progress and is displayed on line 1 of the display (trunked and T99
modes only).
SPKR ON
SPKR OFF
BANK=1-8
External Speaker ON
External Speaker OFF
Displayed when the external speaker is enabled.
Displayed when the external speaker is disabled.
The bank of keys that are going to be loaded when the keyloader loads encryption keys. This is
only valid for radios that support VGS, VGE, or DES encryption. It is displayed on line 2 of
the display when the encryption keyloader is connected.
KEY LOAD
KEY ZERO
Displayed on line 1 of the display when the encryption keyloader is connected.
Displayed on line
2
of the display when the reset and option buttons are pressed
simultaneously for approximately two seconds. The encryption keys are zeroed.
SYS KEY
KEY=1-7
System Key
Displayed on line 1 of the display in the display key mode of the menu. It is followed in the
second line with a key number “KEY = <1..7>”.
Displayed on line 2 of the display in the display key mode of the menu for conventional
systems when the “SYS KEY” or “CHN KEY” is displayed in line 1 and for trunked systems
when the “SYS KEY” or “GRP KEY” is displayed in line 1.
PRIMARY
Displayed on line 1 of the display when the primary keys are enabled.
PRS NAME
Personality Name
Displayed on line 1 of the display under the revision selection of the menu. The personality
name is displayed on line 2 at the same time.
M/A-COM
Displayed on line 1 of the display under the revision selection of the menu. The copyright year
is shown in line 2 of display at the same time “(c) 2007.”
11.3 ALERT TONES
The M7200 series mobile radio provides audible alert tones or “beeps” to indicate the various operating
conditions. These alert tones can be enabled or disabled through programming.
Table 11-3: M7200 EDACS Mode Alert Tones
NAME
TONE
DESCRIPTION
Sounds after keying the radio (Push-To-Talk button is
pressed). Indicates the radio has been assigned a
working channel
Call Originate
A short mid-pitched tone.
Sounds if the programmed time for continuous
transmission is exceeded. The transmitter will shut down
shortly after the alert, interrupting communications.
Release and re-key the PTT button to maintain
communications. This will reset the carrier control timer
and turn the transmitter back on.
Five
short
high-pitched
Carrier Control Timer
Key Press Alert
warning tones followed by a
long low-pitched tone.
Indicates a key has been pressed. A short low-pitched
tone indicates no action was taken because the key is
not active in the current mode.
A short tone.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
11.4 MENU
The menu function accesses features that are not available directly from the keypad. The order and
specific number of menu items available is configurable through programming. Upon radio power up, the
menu item at the beginning of the menu list will always be displayed first. Subsequent access to the menu
function will return the last menu item that was shown in the display. To enter the menu mode, press
MENU. The
ramp control, MENU, and CLR are used during the selection process. All of the
selection mode rules, previously detailed, apply to the menu item selection process with the exception of
direct access. The radio will continue to receive and transmit normally while in the menu function.
A new item is displayed by using the
ramp control to scroll through the list in increasing and
decreasing order. The displayed menu item is made active by pressing MENU.
After entering the menu selection mode, the following generic display format will appear.
M E N U
Y Y Y Y Y Y Y Y
Line 1 indicates the radio is in the menu selection mode. Line 2 indicates the menu item (YYYYYYYY)
that is to be viewed or changed (some menu items provide radio information and do not have changeable
parameters).
An example of the menu item selection process and menu item parameter change is detailed below for the
contrast menu item.
1. Press MENU to enter the menu mode.
2. Press the
ramp control until the display shows:
M E N U
CONTRAST
3. Press MENU. The contrast menu item is activated and the display will be similar to the following:
CNTRST = X
Y Y Y Y Y Y Y Y
Line 1 shows the active menu item and its current parameter setting (XXX). Line 2 shows the
currently selected system or group name (YYYYYYYY).
4. The menu item's parameter setting shown in the display can now be changed by using the
ramp control to scroll through the list of parameter values. Once the desired setting is reached, press
MENU to store the value and return to the normal display. For menu items that display radio
information, use
to scroll through a list of informational displays. The menu items are listed in
Table 11-4: Menu Item Information
PARAMETER
SETTINGS
FEATURE
DISPLAY
COMMENT
Menu Item:
CONTRAST
Once selected:
CNTRST=
Contrast Adjust
1, 2, 3, 4, 5, 6, 7, 8
Selects the Contrast level.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
PARAMETER
SETTINGS
FEATURE
DISPLAY
COMMENT
Informational displays only
(see radio); no user
selectable settings.
Radio Revision
Information
Menu item:
REVISION
Selects the information display to view.
Menu item:
PHN CALL
Phone Call
Once selected: See
Telephone Interconnect
Call Section
Allows access to the Phone Call Feature.
Menu Item: EXTALARM
Once Selected:
EXTALARM
EXTALARM replaces the system name on the
display as long as the external alarm feature is
enabled.
External Alarm
Public Address
ON, OFF
ON, OFF
Menu item:
PUB ADDR
Once selected:
PA ON or
Public Address is toggled ON and OFF.
External Speaker is toggled ON and OFF.
PA OFF
Menu item:
EXT SPKR
External Speaker Once selected:
ON, OFF
SPKR ON or
SPKR OFF
Menu item: KEYLOAD
Once selected:
KEY LOAD BANK = N
Encryption Key
Loading
Enables the radio to accept the loading of encryption
keys.
Up to 8 banks of 7 keys
Menu item: DISP KEY
Once selected:
SYS KEY, GRP KEY or
CHN KEY and KEY = N
Display Current
Encryption
Key(s)
Displays current encryption key number.
Scan
Menu item: SCAN
ON, OFF
Toggles scan function ON or OFF.
Toggles private function ON or OFF.
Menu Item: PRIVATE
Private Mode
Once selected: PVT or key ON, OFF
light.
Menu Item: SQUELCH
Once selected:
SQLCH=xx
Front Panel
Squelch Adjust
1-16
Allows setting of squelch.
Menu item: SCAN ADD
Scan Add
Once selected: Proper scan S, 2 or 1
icon displayed.
Adds group or channel to scan list.
Deletes channel from scan list.
Menu item: SCAN DEL
Once selected: Scan icon
goes out.
Scan Delete
Menu item: SCAN A/D
Scan Add/Delete When selected: Toggles
through scan selections
Toggle sequence
S, 2, 1, S, ...
Changes present group or channel to next scan
choice in scan list.
Menu Item: SCAN ADD
Press twice when actively
Last Scanned
Changes the selected channel to the last scanned
channel.
receiving; three times when
Channel Recall
not receiving. Scan icon
displayed.
Menu item: HOME
Home channel
Changes to the group or channel defined for Home
function.
Once selected: Home group
selection
or channel displayed.
Menu item: SYS SEL
System select
1-64 = (n)umber of desired
system
Displays the system selected.
Once selected: SYS = n
External alarm #2 Menu item: EXTALRM2
ON, OFF
Toggles external alarm #2 feature ON or OFF.
Menu item: SYSGRP 1
Menu item: SYSGRP 2
System and
Changes to the System & Channel programmed for
SYSGRP 1-5.
Menu item: SYSGRP 3
Channel selection
Menu item: SYSGRP 4
Menu item: SYSGRP 5
89
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
PARAMETER
SETTINGS
FEATURE
DISPLAY
COMMENT
Toggles the mute function ON or OFF to control the
audio output from the selected radio.
Mute
Menu item: MUTE
Menu item: MUTE 1
Menu item: MUTE 2
Menu item: RADIO
ON, OFF
Toggles the mute 1 function ON or OFF on radio
#1.
Mute #1
Mute #2
ON, OFF
ON, OFF
ON, OFF
Toggles the mute 2 function ON or OFF on radio
#2.
Multiple radio
operation
Toggles the currently selected radio.
Menu item: RADIO 1
ON, OFF
ON, OFF
Changes to radio #1.
Changes to radio #2.
Radio selection
Menu item: RADIO 2
Menu item: TALKARND
Once selected:
TALKARND on line 1
Talkaround
feature
Toggles talkaround ON or OFF (transmit frequency
changed to receive frequency).
ON, OFF
Menu Item: FEATURES
Once selected:
See Feature Encryption
Display section
Indicates current features program- med into the
Informational displays only; radio as well as certain information required to add
Feature
Encryption
Display
no user selectable settings
features to the radio (refer to the Table of Contents
for Feature Encryption Display.
Menu Item: SYS SCAN
Once selected: SYSC ON ON, OFF
or SYSC OFF
System Scan
Enable
System Scan features like ProScan are toggled ON
and OFF.
Menu Item: T99 ENAB
Once selected:
T99 ON or T99 OFF
Type 99 Decode
Enable
ON, OFF
Type 99 Decode is toggled ON and OFF.
11.5 GROUP CALLS IN P25 MODE
11.5.1 Transmitting a Group Call
1. Select the desired P25 system.
2. Select the Talk Group/Conventional Channel (selected simultaneously using either the
system/group/channel knob or the group key).
3. Press and hold the PTT.
4. When a grant tone is received (if enabled through programming), speak into the microphone.
5. Release PTT and wait for response.
11.5.2 Receiving a Group Call
The radio will unmute according to the squelch mode defined in the radio personality (monitor, normal,
selective).
1. Select the desired P25 system and Talk Group/Channel or turn scan on and make sure the desired
channel is in the scan list.
2. When the radio receives a P25 call, the radio will unmute and the channel name will appear in the
display.
3. Press the PTT button to respond.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
11.6 INDIVIDUAL CALLS IN P25 MODE
11.6.1 Transmitting an Individual Call
1. Select the desired P25 system.
2. Select the radio unit to call (callee source ID) from the pre-programmed individual call list or enter
the ID number on the radio keypad.
3. Press and hold the PTT.
4. When grant tone is received (if enabled through programming) speak into the microphone.
5. Release the PTT.
11.6.2 Receiving an Individual Call
The radio will unmute according to the squelch mode defined in the radio personality (monitor, normal,
selective).
1. Select the desired P25 system and Talk Group/Channel or turn scan on and make sure the desired
channel is in the scan list.
2. When the radio receives a P25 call, the radio will unmute and the ID of the transmitting radio will
appear in the display.
3. Press the PTT button to respond.
Unanswered calls will appear in the Who Has Called (WHC) list.
11.7 EMERGENCY GROUP CALLS IN P25 MODE
There is no method available for a system-wide Emergency clear. An emergency group call
must be cleared on each individual radio.
11.7.1 Declaring an Emergency Group Call
1. Select the desired P25 system and Talk Group/Channel.
2. Press the red emergency button on the top of the radio. The radio will broadcast a short emergency
transmission with the emergency bit set. “TXEMER” will appear in the display of the transmitting
radio.
3. To send a voice message, press the PTT and speak into the microphone.
4. To clear an emergency from the transmitting radio, perform one of the following steps:
a. Change systems.
b. Change channels (if not prohibited by programming).
c. Cycle power by turning radio off and then back on.
d. Press the Clear and Emergency buttons simultaneously, providing the Clear Emergency option is
enabled in the Supervisory Options in the personality.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
11.7.2 Receiving an Emergency Group Call
1. Select the desired P25 System and Talk Group/Channel.
2. When the radio detects an incoming Emergency Group Call, the radio will sound an alert tone and
“RXEMER” will appear in the display.
3. Voice or emergency transmissions will be heard at the receiving radio.
4. To clear an emergency from the receiving radio, perform one of the following steps:
a. Change systems.
b. Change channels (if not prohibited by programming).
c. Cycle power by turning radio off and then back on.
d. Press the Clear and Emergency buttons simultaneously, providing the Clear Emergency option is
enabled in the Supervisory Options in the personality.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
12 BASIC TROUBLESHOOTING
If the radio is not operating properly, check Table 12-1 for likely causes. For additional assistance,
contact a qualified service technician.
Table 12-1: Basic Troubleshooting
SYMPTOM
CAUSE
SOLUTION
Test the connection to the vehicle power
supply.
Radio will not turn on. No power.
If in multiple control head
Radio will not turn off. configuration, one of the attached Power off all control heads.
control heads is still powered up.
Radio will not register
or does not receive
provisioning data.
Bad log in credentials.
Check log in and password.
Increase the volume level.
No audio.
Speaker volume is muted.
Check network connectivity and move to a
better coverage area if possible. Report the
area without coverage to an authorized
network technician.
Transmitting or receiving in a
poor coverage area or subject to
interference.
Poor audio.
Ambient Light Sensor is
obstructed.
Clear the obstruction and give the sensor a
clear path to ambient light.
Poor display visibility.
Radio is out-of-range or cannot
connect with the OpenSky
network.
Return to coverage area if possible and
wait for condition to clear.
No network
connectivity icon in
display.
Use single-site trunking or switch to an
alternate channel.
Base station network connection
has failed.
Return to coverage area if possible. If
overheated, let radio cool before retrying
transmission. Report this failure to an
authorized technician.
Radio will not
transmit.
Radio may be out of coverage
area or may be overheated.
Radio control head is unable to
communicate with mobile radio
unit (radio transceiver).
“Warning: No MRU”
Message.
Have the radio connections checked by an
authorized technician.
In multiple control head
configurations, another user is
operating the radio from another
control head.
Control head
randomly changes
display.
None
Encrypted calls cannot
be made.
Contact system administrator to request
encryption privileges.
Not authorized to use.
Screen displays:
UNAUTH3
The radio network ID has not
been added to the network.
Contact system administrator.
Contact system administrator.
Screen displays:
NOAUTHV
Radio authentication of the
VNIC failed.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
SYMPTOM
CAUSE
SOLUTION
Screen displays:
NOAUTHM
VNIC authentication of the radio
failed.
Contact system administrator.
The voice authentication security
policy is set to only allow
authenticated users.
Screen displays:
NOSUPRT
Contact system administrator.
Log in (refer to Section 7.14.1).
Encrypted calls cannot
be made.
User not logged in.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
13 TECHNICAL ASSISTANCE
The Technical Assistance Center's (TAC) resources are available to help with overall system operation,
maintenance, upgrades and product support. TAC is the point of contact when answers are needed to
technical questions.
Product specialists, with detailed knowledge of product operation, maintenance and repair provide
technical support via a toll-free (in North American) telephone number. Support is also available through
mail, fax and e-mail.
For more information about technical assistance services, contact your sales representative, or call the
Technical Assistance Center at:
North America:
International:
Fax:
1-800-528-7711
1-434-385-2400
1-434-455-6712
E-mail:
95
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
14 KEYPAD REMAPPING
If the keys have been remapped to provide new functions, fill in the following template for future reference.
Button
Function
Button
Function
Emergency
1
Preset A
Preset B
Preset C
Rocker •
Rocker ••
Rocker +
Rocker -
2
3
4
5
6
7
8
MENU
9
OPT/OPTION
CLR/CLEAR
SCAN
*
0
#
96
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
SYSTEM NUMBER
SYSTEM NAME
TRK/CNV
GRP/CHN NUMBER
GRP/CHN NAME
USE
98
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
SYSTEM NUMBER
SYSTEM NAME
TRK/CNV
GRP/CHN NUMBER
GRP/CHN NAME
USE
99
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
SYSTEM NUMBER
SYSTEM NAME
TRK/CNV
GRP/CHN NUMBER
GRP/CHN NAME
USE
100
Download from Www.Somanuals.com. All Manuals Search And Download.
MM23016, Rev. C
16 WARRANTY
A. M/A-COM, Inc. (hereinafter "Seller") warrants to the original purchaser for use (hereinafter "Buyer") that Equipment manufactured
by or for the Seller shall be free from defects in material and workmanship, and shall conform to its published specifications. With
respect to all non-M/A-COM Equipment, Seller gives no warranty, and only the warranty, if any, given by the manufacturer shall
apply. Rechargeable batteries are excluded from this warranty but are warranted under a separate Rechargeable Battery
Warranty (ECR-7048).
B. Seller’s obligations set forth in Paragraph C below shall apply only to failures to meet the above warranties occurring within the
following periods of time from date of sale to the Buyer and are conditioned on Buyer’s giving written notice to Seller within thirty
(30) days of such occurrence:
1. for fuses and non-rechargeable batteries, operable on arrival only.
2. for parts and accessories (except as noted in B.1) sold by Seller’s Service Parts Operation, ninety (90) days.
3. for P7200, P7100IP, P5400, P5300, P5200, P5100, P3300, PANTHER™ 405P and 605P, M7300, M7200 (including V-TAC),
M7100 IP, M5300 and M3300 radios, two (2) years, effective 10/01/2007.
4. for all other equipment of Seller’s manufacture, one (1) year.
C. If any Equipment fails to meet the foregoing warranties, Seller shall correct the failure at its option (i) by repairing any defective or
damaged part or parts thereof, (ii) by making available at Seller’s factory any necessary repaired or replacement parts, or (iii) by
replacing the failed Equipment with equivalent new or refurbished Equipment. Any repaired or replacement part furnished
hereunder shall be warranted for the remainder of the warranty period of the Equipment in which it is installed. Where such
failure cannot be corrected by Seller’s reasonable efforts, the parties will negotiate an equitable adjustment in price. Labor to
perform warranty service will be provided at no charge during the warranty period only for the Equipment covered under
Paragraph B.3 and B.4. To be eligible for no-charge labor, service must be performed at a M/A-COM factory, by an Authorized
Service Center (ASC) or other Servicer approved for these purposes either at its place of business during normal business hours,
for mobile or personal equipment, or at the Buyer’s location, for fixed location equipment. Service on fixed location equipment
more than thirty (30) miles from the Service Center or other approved Servicer’s place of business will include a charge for
transportation.
D. Seller’s obligations under Paragraph C shall not apply to any Equipment, or part thereof, which (i) has been modified or otherwise
altered other than pursuant to Seller’s written instructions or written approval or, (ii) is normally consumed in operation or, (iii) has
a normal life inherently shorter than the warranty periods specified in Paragraph B, or (iv) is not properly stored, installed, used,
maintained or repaired, or, (v) has been subjected to any other kind of misuse or detrimental exposure, or has been involved in
an accident.
E. The preceding paragraphs set forth the exclusive remedies for claims based upon defects in or nonconformity of the Equipment,
whether the claim is in contract, warranty, tort (including negligence), strict liability or otherwise, and however instituted. Upon the
expiration of the warranty period, all such liability shall terminate. The foregoing warranties are exclusive and in lieu of all other
warranties, whether oral, written, expressed, implied or statutory. NO IMPLIED OR STATUTORY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE SHALL APPLY. IN NO EVENT SHALL THE SELLER BE
LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT OR EXEMPLARY DAMAGES.
This warranty applies only within the United States.
M/A-COM, Inc.
M/A-COM, Inc.
1011 Pawtucket Blvd.
Lowell, MA 01853
1-877-OPENSKY
221 Jefferson Ridge Parkway
Lynchburg, VA 24501
1-800-528-7711
ECR-7047F
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Tyco Electronics Wireless Systems Segment
221 Jefferson Ridge Parkway
Lynchburg, Virginia 24501
(Outside USA, 1-434-385-2400) Toll Free 1-800-528-7711
www.macom-wireless.com
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|