OWNER’S MANUAL
Trimmer/Mower
•
•
•
•
•
•
Safety
Assembly
Features and Controls
Operation
Maintenance
Parts List
SAFETY FIRST!
Before operating this equipment, read this
Owner's Manual and the separate manual
supplied by the engine manufacturer.
Model
52067 - 5HP
GARDEN WAY INCORPORATED
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Section
Safety
1
SPARK ARRESTER WARNING TO RESIDENTS
OF CALIFORNIA AND SEVERAL OTHER STATES
Trimmer Head Control Bail
Engine Throttle Control Lever
Under California law, and under the laws of several
other states, you are not permitted to operate an inter-
nal combustion engine using hydrocarbon fuels on
any forest, brush, hay, grain, or grass covered land; or
land covered by any flammable agricultural crop with-
out an engine spark arrester in continuous effective
working order.
Handlebar
Height Adjuster
The engine on the unit is an internal combustion en-
gine which burns gasoline, a hydrocarbon fuel, and
must be equipped with a spark arrester muffler in con-
tinuous effective working order. The spark arrester
must be attached to the engine exhaust system in
such a manner that flames or heat from the system
will not ignite flammable material. Failure of the
owner/operator of the unit to comply with this regula-
tion is a misdemeanor under California law (and other
states) and may also be a violation of other state
and/or federal regulations, laws, ordinances or codes.
Contact your local fire marshal or forest service for
specific information about which regulations apply in
your area.
Debris Shield
Trimmer Head
Debris Flap
Figure 1-1
IMPORTANT
Safe Operation Practices for Walk-Behind Mower
This cutting machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
5. Be sure the area is clear of other peo-
ple (particularly small children and pets)
before mowing. Stop machine if anyone
enters the area. Keep bystanders at least
50 feet from the area of operation.
11. Refer to provided instructions for
GENERAL OPERATION
proper operation and installation of ac-
cessories. Only use factory-approved
accessories.
1. Read, understand, and follow all in-
structions on the machine and in the
manuals. Be thoroughly familiar with the
controls and the proper use of the equip-
ment before starting.
12. Stop trimmer head when crossing
gravel drives, walks, or roads. Wait for
trimmer lines to stop.
2. Do not put hands or
feet near or under rotat-
ing parts. Keep clear of
the rotating trimmer
head and line at all
times.
13. Stop engine and disconnect spark
plug wire from spark plug whenever you
leave the unit, clean the equipment, or re-
place trimmer line.
6. Do not operate the machine when
barefoot or wearing open sandals. Always
wear substantial footwear.
14. Wait until the trimmer
head comes to a complete
stop, shut the engine off,
and disconnect the
spark plug wire be-
fore installing or re-
moving trimmer line. Be sure
trimmer head is securely attached before
operating equipment.
7. Wear appropriate clothing such as a
long-sleeved shirt or jacket and long
trousers or slacks. Do not wear shorts.
3. Only allow responsible adults, who
are familiar with the instructions, to oper-
ate the trimmer/mower. Never let children
or untrained adults operate this
equipment.
8. Do not wear loose clothing– it could
catch in the equipment.
9. Do not mow in reverse unless abso-
lutely necessary. Always look down and
behind before and while moving
backwards.
4. Inspect the area where the machine is
to be used. The machine can propel small
objects at high speed, causing personal
injury or property damage. Clear the area
of objects such as rocks, toys, wire,
bones, sticks, etc., which could be picked
up and thrown by the trimmer line.
15. Mow only during daylight hours or
when good artificial light is available.
10. Do not operate the unit without
proper guards, plates, or other protective
safety devices in place.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Section 1: Safety
16. Do not operate the machine while
under the influence of alcohol or drugs,
or when tired or ill.
27. Be aware of where the machine is
discharging materials and do not point
the discharge at anyone.
Do Not:
Do not mow near drop-offs, ditches, or
embankments. You could lose footing
or balance.
28. Never run the engine in an enclosed
area. Engine exhaust contains carbon
monoxide, a deadly gas that is odorless,
colorless and tasteless. Always run the
engine outdoors where there is adequate
ventilation.
17. If using machine in wet conditions,
exercise extreme care to prevent loss of
footing. Wear footwear that will improve
traction. Avoid sloping ground. Hold the
handlebars with two hands and walk;
never run.
Do not mow on very steep slopes.
Do not mow on wet grass. Slippery
footing can be hazardous.
CHILDREN
29. Slow down before turning.
18. Release Trimmer Head Control Bail
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the ma-
chine and the mowing activity. Never as-
sume that children will remain where you
last saw them.
before starting engine.
30. Shut off engine when not trimming
or mowing.
19. If the unit starts to vibrate abnor-
mally, stop the engine and disconnect the
spark plug wire. Check immediately for
the cause. Vibration is generally a warn-
ing of trouble.
31. Use extra care when loading or un-
loading machine into a trailer or truck.
32. Use this equipment for its intended
purpose only.
1. Keep children out of the mowing area
and under the watchful care of a respon-
sible adult.
20. Always wear approved safety gog-
gles or safety glasses with side shields
when operating equipment. The use of
any powered machine can result in for-
eign objects being thrown by highspeed
rotating parts which can cause personal
injury or property damage. Stay away
from glass and other easily thrown or
breakable objects.
33. Always make sure the handlebars are
tight and comfortably positioned. They
should never be in an awkward position
for the operator.
2. Be alert and turn machine off if chil-
dren enter the area.
3. Before and while moving backwards,
look behind and down for small children.
SLOPE OPERATION
Slopes are a major factor related to loss
of control and tip-over accidents which
can result in severe injury or death. All
slopes require extra caution. If you can
not back up the slope or you feel uneasy
on a slope, do not mow it.
4. Never allow children to operate the
machine.
21. Wear work gloves and sturdy
footwear when using this equipment.
Leather work shoes or short boots are
ideal. They protect ankles and shins from
rocks, pebbles, splinters, etc.
5. Use extra care near blind corners,
shrubs, trees, or other objects that may
obscure vision.
6. Never carry children, even with the
trimmer head stopped. Children may fall
off and be seriously injured or interfere
with safe machine operation.
Do:
22. It is advisable to wear protective
headgear to prevent the possibility of
being hit by small flying particles, etc.
Mow across the face of slopes; never
up and down. Exercise extreme cau-
tion when changing direction on
slopes. Avoid slopes greater than 15o.
7. Do not allow children nearby if you
are working.
23. Before each use, inspect the Throttle
Control Lever and cable. Make sure the
cable is free and the lever functions
properly.
Remove objects such as rocks, tree
limbs, etc.
SERVICE
Uneven terrain could overturn the ma-
chine. Watch for holes, ruts, or
bumps. Tall grass can hide obstacles.
1. Use extra care in handling gasoline
and other fuels. They are flammable and
their vapors are explosive. To help pre-
vent a fire or explosion:
24. Watch for traffic when near or when
crossing roadways.
25. Never attempt to carry children or
other passengers on the equipment. They
could fall off and be seriously injured, or
they could interfere with safe operation of
the equipment.
Use slow speed.
Use extra care with grass catchers or
other attachments. These can change
the stability of the machine. Keep all
movement on the slopes slow and
gradual.
a) Use only an approved container.
b) Never remove gas cap or add fuel
when the engine is running. Let en-
gine cool before refueling. Do not
smoke.
26. The machine is equipped with a plas-
tic debris shield in front of the engine and
a rubber debris flap under the frame.
They must be in place and working prop-
erly. Never remove or cause the debris
shield or debris flap to cease working. If
either of these parts is missing or not
working properly, do not use the equip-
ment until this situation is corrected.
Avoid starting or stopping on a slope.
c) Never refuel the machine indoors.
Fill the fuel tank outdoors and with
extreme care.
d) Never store the machine or fuel
container inside where there is an
open flame, such as a water
heater, etc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Safety
3
e) Replace caps on the fuel tank and
fuel container and clean up spilled
fuel before starting engine. Move
machine away from any gasoline
fumes before starting the engine.
6. To reduce fire hazard, keep mower
free of grass, leaves or other debris
build-up. Clean up oil or fuel spills. Let
machine cool before storing.
12. Do not change the engine governor
setting or overspeed the engine. The
governor controls maximum safe operat-
ing speed and protects the engine and all
moving parts from damage caused by
overspeed. Authorized service shall be
sought if a problem exists.
7. After striking an object, stop the en-
gine and disconnect the spark plug wire.
Inspect the machine and repair, if neces-
sary, before restarting.
f) Keep matches, smoking materials,
open flames, and sparks away
from the fuel tank and fuel
container.
13. Do not touch engine parts which may
be hot from operation. Allow parts to cool
completely before inspecting, cleaning or
repairing the unit.
8. Never make adjustments or repairs
while engine is running.
g) Leave 1/2" air space at the top of
the fuel tank to allow for fuel ex-
pansion.
9. Components subject to wear, damage
and deterioration could expose moving
parts or allow objects to be thrown.
Frequently check components and re-
place with factory recommended parts,
when necessary. Regularly inspect the
trimmer head and debris shield. Make
sure they are not bent, damaged, or
loose.
14. Maintain or replace safety and in-
structional decals. Refer to the Parts List
for replacement decal information.
2. Never run the engine inside a closed
area.
3. Never clean, or make adjustments or
repairs with the engine running.
Disconnect the spark plug wire and keep
the wire away from the plug to prevent
accidental starting. Remove key on elec-
tric start models.
15. Use only original-equipment replace-
ment parts. Parts manufactured by oth-
ers could present safety hazards and af-
fect performance even though they may
fit on this trimmer/mower.
10. Only use eighteen-inch long .130" or
.155" diameter trimmer line. Never use
other lengths, diameters or material as
trimmer line.
16. Remember– the end of the season is
a good time to inspect equipment prior to
storage.
4. Keep all nuts and bolts tight, espe-
cially the trimmer head attachment bolts,
and keep equipment in good condition.
Check mounting hardware on trimmer
head every time you change trimmer line
and prior to each use.
17. To guard against engine overheating,
always keep the engine debris guard
mounted and clean.
11. Trimmer line moves at high speed
and can cut. Always stop
the engine and let all mov-
ing parts stop before re-
placing the trimmer lines.
Let the engine cool.
5. Never tamper with safety devices.
Check their proper operation regularly.
Safety Decals
Make certain that all safety decals on this equipment are
kept clean and in good condition. The decals are shown
(at reduced sizes) below. If you need a replacement decal,
please refer to the Parts List in this Manual.
WARNING
THROWN OBJECT HAZARD
Objects will be thrown violently by the
•
cutting head, resulting in significant hazard!
Keep children, pets and bystanders 50 feet
•
away from machine while operating.
Be alert to hidden obstacles.
•
READ OWNERS MANUAL
If you need a replacement manual, write to the
address listed on the serial number decal on
this unit.
On engine, above muffler
ROTATING CUTTING HEAD
Do not service or adjust cutting head or other
moving parts unless engine is stopped and
spark plug wire is disconnected.
1918115 (12/99)
STOP
On left
handlebar
On right
handlebar
On top of deck
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Section
Assembly
2
5. Use two cable ties (F, Figure 2-2) to
secure the trimmer head control cable (C)
to the handlebar as shown.
STEP 1: Unpack Unit
WARNING
1. Remove the protective packaging ma-
terial (plastic film and cardboard) from
the handlebars and the unit.
To prevent personal injury or property
damage, do not attempt to start the
engine until all assembly steps are
complete and you have read and under-
stand all of the safety and
the operating instructions in this
Manual.
2. Remove the handlebars from the insert
and carefully (do not pinch or kink the at-
tached cable) put them aside before re-
moving the unit from the shipping carton.
STEP 3: Attach Throttle Control
Lever
1. One end of the throttle control cable
(H, Figure 2-3) is attached to the engine.
Gently unwind the cable from its shipping
position and position the Throttle Control
Lever (I) on the outside of the right han-
dlebar, next to the throttle control decal.
3. Compare the parts inside the carton
with the following list:
INTRODUCTION
• Machine Assembly (A, Figure 2-1)
Carefully follow these assembly steps to
correctly prepare your machine for use.
It is recommended that you read this
Section in its entirety before beginning
assembly.
• Extra Trimmer Line (B, Figure 2-1): six
pieces of heavy-duty .130" dia. line and
six pieces of extra heavy-duty .155" dia.
line.
• The following items are in a separate
package:
2. Secure the Throttle Control Lever to
the handlebar with a 1/4-20 x 2 hex hd.
screw (J, Figure 2-3) and 1/4-20 hex
locknut (K).
3. Use a cable tie (L, Figure 2-3) to se-
cure the throttle cable (H) to the handle-
bar as shown.
(3) Plastic cable ties
INSPECTION AFTER DELIVERY
(1) Hex Hd. Screw, 1/4-20 x 2
(1) Hex Locknut, 1/4-20
(2) Hex Hd. Screw, 5/16-18 x 2
(2) Hex Locknut, 5/16-18
Inspect your machine immediately after it
has been delivered. Make sure that nei-
ther the carton nor the contents have
been damaged.
STEP 4: Add Motor Oil
1. The engine is shipped without motor
oil which MUST BE ADDED before the en-
gine is started.
If you find or suspect any damage, con-
tact the carrier (trucking company) right
away. Inform them of the specific dam-
age and that you wish to file a claim. To
protect your rights, be sure to put this in
writing to the carrier within 15 days after
your machine arrives. Please let us know
if you need assistance with this matter.
STEP 2: Install Handlebars
1. Cut the plastic tie and remove the tape
that secures the control bail (G, Figure 2-
2) to the handlebar (A).
2. See the separate engine manual for
filling instructions and for oil specifica-
tions. The engine must be level when
checking the oil level. In ambient tem-
peratures above 400 F, use a high-quality,
SAE #30 weight detergent oil classified
for Service SF, SG or SH. Use no special
additives. Do not mix oil with fuel.
NOTE: Do not pinch or kink the attached
cable while unfolding and securing the
handlebars.
IMPORTANT: The engine is shipped
without motor oil in its crankcase. Motor
oil must be added to the engine before
starting.
2. Carefully lift the handlebars (A, Figure
2-2) to rear of the unit and align the han-
dlebar legs with the handlebar support
bracket (B).
STEP 5: Check Trimmer Head
Hardware
Check that the two bolts (M, Figure 2-4)
on the trimmer head are tightened se-
curely. The trimmer head can be rotated
to check the bolts.
3. Route the trimmer head control cable
(C, Figure 2-2) to the outside of the
handlebar.
NOTE: LEFT and RIGHT sides of unit are
as viewed from operator’s position be-
hind the handlebars.
4. Select the low or high height setting
holes in the handlebar legs and attach the
legs with the two 5/16-18 x 2 hex hd.
screws (D) and 5/16-18 locknuts (E)
from the hardware bag.
ASSEMBLY STEPS
Tools/Supplies Needed:
• (1) Utility Knife or Scissors
IMPORTANT: The trimmer head hardware
is designed to be permanently installed
and is not removable. Do not attempt to
replace it with non-factory specified
hardware.
• (2) 1/2" (or adjustable) Wrenches
IMPORTANT: Adjust the handlebars as
close as possible to waist level so that
your arms are at a comfortable height.
This position will result in less pressure
on the mower wear cup, making the unit
easier to roll and reducing wear to the
wear cup.
• (2) 7/16" Wrenches (one with a
boxed end)
• Motor Oil (see engine manual for oil
specifications and quantity required)
NOTE: The two holes (one is covered
with a plastic plug) on the top, front end
of the mower deck are access holes that
allow certain parts to be serviced.
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Assembly
5
I
A
J
I
K
H
L
B
Figure 2-3: Attach throttle lever to right-side handlebar.
Figure 2-1
A
G
M
F
C
F
B
M
D
E
Figure 2-4: Check trimmer head hardware for tightness.
Figure 2-2: Handlebar installation.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Section
Features and Controls
3
OPERATING SYMBOLS
STOP
Various symbols (shown here, with
word descriptions) are used on the
unit.
ENGAGE
BAIL
DISENGAGE
BAIL
FAST
ENGINE
STOP
TRIMMER
HEAD
SLOW
STOP
Handlebar Height Adjustment
The handlebar (D, Figure 3-1) has two
height settings (see “Adjust Handlebar
Height” in Section 4).
Fuel Primer Button
WARNING
The fuel primer button (H, Figure 3-1) al-
lows a cold engine to be primed for
faster, easier starting.
Before operating your machine, care-
fully read and understand all safety,
controls and operating instructions in
this Manual, the separate Engine
Owner’s Manual, and on the decals on
the machine.
Plastic Debris Shield
A heavy-duty plastic shield (E, Figures 3-
1 and 3-1A) protects the engine from all
manner of debris. The shield tilts for-
ward for access to the engine.
Failure to follow these instructions can
result in serious personal injury.
E
Engine Throttle Control Lever
Use this lever (F, Figure 3-1) to regulate
engine speed and to stop the engine. The
throttle settings are shown on the decal
next to the lever.
FEATURES AND CONTROLS
This Section describes the location and
function of the features and controls on
your machine. Refer to the “Operation”
Section for detailed operating
instructions.
Figure 3-1A: Debris shield in operating
position.
Engine Recoil Starter
The recoil starter is located at the rear of
the engine (G, Figure 3-1) and is used to
pull start the engine.
IMPORTANT: Refer to the separate en-
gine manual for detailed information
about the controls on the engine.
F
Trimmer Head Control Bail
Pull the control bail (A, Figure 3-1) up
against the handlebar (engage bail) to
start rotation of the trimmer head. Let go
of the control bail (disengage bail) to stop
the trimmer head.
A
G
Cutting Height Settings
D
The trimmer head (B, Figure 3-1) is ad-
justable to an infinite number of height
settings from 1-1/2"-to-4-1/2".
E
H
Trimmer Line Holders
The two trimming lines are secured to line
holders (C, Figure 3-1). Replacing the
trimmer lines is easy (refer to “Changing
Trimmer Lines” in Section 5).
B
C
Figure 3-1: Features and controls
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Section
Operation
4
The cutting height of the trimmer line can
be adjusted between 1-1/2" and 4-1/2"
high in infinite increments. Start at a
higher setting and make adjustments as
needed.
FILL FUEL TANK
WARNING
Before operating your machine, care-
fully read and understand all safety
(Section 1), controls (Section 3) and op-
erating instructions (Section 4) in this
Manual, in the separate Engine Owner’s
Manual, and on the decals on the
machine.
DANGER
GASOLINE IS HIGHLY FLAMMABLE AND
ITS VAPORS ARE EXPLOSIVE.
In general, use higher settings to handle
taller material and to cope with tougher
cutting conditions. Use any trimming
height for less demanding conditions.
To adjust the cutting height:
Follow gasoline safety rules in this
Manual (see Section 1) and in the
separate Engine Owner’s Manual.
Failure to follow gasoline safety rules
and instructions can result in serious
personal injury and property damage.
Failure to follow these instructions can
result in serious personal injury.
1. The cutting line height can be
changed when the wear cup is resting on
the ground. If necessary, tip the unit
back slightly for a better view (do not tip
unit all the way back or motor oil may
flow to the exhaust area and the engine
may smoke for several seconds when
restarted).
INTRODUCTION
1. Lift and tilt plastic debris shield (E,
Figure 3-1) forward.
Read this Section thoroughly before you
start the engine. As with any piece of
outdoor power equipment, getting the
“feel” for how your machine operates and
knowing the best techniques for particu-
lar jobs are important to overall good
performance.
2. Clean fuel fill area and engine each
time before fuel is added. (See “Cleaning
Debris” in engine manual.)
3. Add gasoline according to the direc-
tions in the engine manual. Follow all in-
structions and safety rules carefully.
2. Use a 1/2" wrench to loosen both
bolts (A, Figure 4-1) securing the trimmer
head. Do not try to loosen the two nuts.
NOTE: All references to LEFT, RIGHT,
FRONT and REAR of the machine are de-
termined by standing in the operator’s
position.
4. Securely replace the fuel tank cap and
the fuel container cap. Promptly wipe up
any fuel spills.
A
5. Lift and tilt the debris shield back,
then push it down to secure it.
PRE-START CHECKLIST
1. Review Section 1: “Safety” and also
Section 3: “Features and Controls”.
ADJUST HANDLEBAR HEIGHT
2. Check for loose or missing hardware.
Tighten or replace as needed.
To adjust handlebar height, refer to “Install
Handlebars” in the “Assembly” Section of
this Manual.
A
3. Check that the engine oil level is up to
the “FULL” mark on the oil dipstick. (See
the engine manual for instructions.)*
Figure 4-1
3. The cutting heights are stamped into
the spindle head (Figure 4-2). Move the
top of the trimmer head to the desired
setting.
CAUTION
4. Check the fuel level. (See the engine
manual and this page for instructions.)*
Before adjusting handlebar height, stop
engine and wait for all moving parts to
stop, disconnect spark plug wire and
prevent it from touching spark plug.
5. Check the Trimmer Head Control Bail
and the Engine Throttle Control Lever for
freedom of movement.
Height
Guide
Failure to comply could result in
personal injury or property damage.
6. Select the cutting height (see “Adjust
Line Cutting Height” in this Section).
7. Check handlebar height position.
8. Carefully check the area to be
trimmed and remove any debris.
ADJUST LINE CUTTING HEIGHT
9. Install the correct diameter trimmer
line (see “Use Correct Diameter Trimmer
Line” in this Section).
CAUTION
Figure 4-2
Before adjusting the cutting height, shut
off the engine, wait for all moving parts
to stop, allow the engine to cool, dis-
connect the spark plug wire and prevent
it from touching the spark plug.
10. Check that the spark plug wire is se-
curely attached to the spark plug.
4. Tighten both trimmer head bolts se-
curely (to 75 in/lbs.) and equally.
* Clean debris from around fuel cap, oil
dipstick, and engine before checking oil
level or adding gasoline.
Failure to comply could result in per-
sonal injury or property damage.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Section 4: Operation
6. Start the engine as follows:
USE CORRECT DIAMETER
TRIMMER LINE
For tougher cutting conditions, use two
(or four) sections of the thicker, .155" di-
ameter extra-heavy duty line.
a) Put the Engine Throttle Control
Lever in the FAST position.
b) Push in the fuel primer button as
instructed in the engine manual.
NOTE: Do not use primer to restart
a warm engine after a short shut-
down.
A
For less demanding conditions, use two
sections of the thinner, .130" diameter
heavy-duty line.
c) Pull recoil start rope slowly until re-
sistance is felt. Then pull rope out
rapidly to start engine. Let rope
back in slowly.
Figure 4-3: Control bail disengaged.
The thicker line has the heft to chop
through tougher materials, while the thin-
ner line provides a more precise cut. To
change trimmer lines, refer to “Changing
Trimmer Lines” in Section 5.
NOTE: If engine fails to start after
three pulls, repeat steps b-c.
NOTE: The thinner line is also recom-
mended for use near trees or shrubs to
help prevent girdling (cutting the bark).
To Start the Trimmer Head
1. Stand in the operator’s position di-
rectly behind the handlebars.
2. Slowly pull the Trimmer Head Control
Bail (Figure 4-4) against the handlebars
to activate the trimmer head. Use the
Engine Throttle Control Lever to adjust
the turning speed of the trimmer head.
HOW TO USE TRIMMER HEAD
CONTROL BAIL
The Trimmer Head Control Bail (A, Figure
4-3) is used to start and stop trimmer
head motion.
Figure 4-4: Control bail engaged.
WARNING
3. Once the trimmer head is revolving,
push the unit forward to trim.
If the trimmer head control bail is not
operating properly, shut off the
engine, disconnect the spark plug wire
and move wire away from plug.
1. Leave the control bail in the disen-
gaged (released) position when starting
the engine to prevent the trimmer head
from turning when the engine starts. See
Figure 4-3.
To Stop the Trimmer Head
Let go of the Trimmer Head Control Bail.
Adjust or repair the control bail before
using the trimmer/mower.
To Stop the Engine
2. When the engine is running, pull and
hold the control bail up against the han-
dlebar (Figure 4-4) to start rotation of the
trimmer head.
Put the Engine Throttle Control Lever in
the STOP position. (If time allows, first
move throttle lever to SLOW setting be-
fore stopping engine.)
Failure to follow this instruction could
result in personal injury or property
damage.
3. Let go of the control bail to stop the
trimmer head. The control bail should
spring forward to the disengaged posi-
tion. If it doesn’t, do not use the machine
until the control bail has been repaired.
OPERATING THE MACHINE
NOTE: If unit is operated in a station-
ary position with the wear cup in con-
tact with dry vegetation, significant
heat will result that may deform the
plastic spindle or scorch vegetation.
Once you have read and understood the
sections in this Manual on “Safety”,
“Assembly”, “Features and Controls”, and
“Operation”, you are ready to start and
operate your machine.
Starting The Engine
OPERATING TIPS AND
TECHNIQUES
1. Complete the “Pre-Start Checklist” in
this Section of the Manual. You must
wear safety glasses or goggles.
Tips for Precision Cutting
For the most precise cutting possible, se-
lect the most appropriate line cutting
height and trimmer line size (thickness)
for the conditions.
2. Move the unit to the work area.
3. Connect the spark plug wire to the
spark plug.
4. Put on safety-approved eye
protection.
5. Release (disengage) the Trimmer
Head Control Bail (A, Figure 4-3).
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation 9
Clean Unit Frequently
Use Correct Walking Speed
Use a travel speed that is suitable for the
mowing conditions. You’ll get better re-
sults at slower walking speeds if the
growth is tall or lush. Shorter or less
dense growth can be cut at faster walking
speeds.
WARNING
THROWN OBJECT HAZARD!
Clean under the mower deck frequently to
remove any grass buildup. Also clean
around the muffler and on top of engine.
See the cleaning instructions in Section
5: “Maintenance.”
• Objects such as rocks, pebbles, and
small debris will be thrown violently
by the cutting head, resulting in sig-
nificant hazard to eyes and exposed
body parts.
Do Not Let Trimmer Lines
Become Too Short
• Always wear safety-approved eye pro-
tection and suitable clothing and
footwear.
Vary Throttle Speed For
Conditions
The vast majority of trimming and mow-
ing jobs will yield the best results if the
engine throttle is set at the fastest engine
speed.
Once the trimmer lines are worn to less
than 1/2 their original length, trimming
jobs begin to take far longer than they
should. As a general guideline, once line
length becomes half of its original length,
it’s time to change to new lines.
• Keep children, pets and bystanders
50 feet away from machine while
operating.
• Be alert to hidden obstacles.
Less demanding jobs (and projects that
require very precise cutting) will yield
better results if the engine speed is
backed off somewhat. (For example,
damage to trees and shrubs can be
avoided by reducing the engine speed,
using the lighter .130" diameter line, and
by keeping a safe distance away.)
Failure to comply could result in
injury or property damage.
Use Extreme Caution on Slopes
When operating on sloping ground, use
extreme caution and common sense to
avoid possible injury or property damage.
When mowing, let the cutting head rest
lightly on the ground and do not lift up or
push down on the handlebars. This tech-
nique allows the cutting head to follow
the ground contour closely, resulting in
the most even cut possible. Also, be sure
to ease into heavy growth to prevent
overwhelming the machine.
Do not mow on excessively steep slopes!
Avoid slopes if greater than 15o or wher-
ever footing is unsure. If a slope is diffi-
cult to stand on, it is probably too steep
to trim or mow. In this case, it may be
wiser to establish a permanent ground
cover on this area.
Again, once you begin a particular job
and get a “feel” for the conditions, you
will be able to make adjustments for the
best possible results.
Trim When Wet or Dry
Keep Mowed Side to Your Right
as You Move Ahead
The unit feeds cut materials to the right
side. Stay on the right side of unmowed
growth as you move along.
Do not trim on slopes when the ground is
slippery. Trim across the face of a slope,
not up and down. Slow down and exer-
cise caution when changing direction on
slopes.
Grass and most other materials are most
efficiently trimmed when dry. But the
unit will do a fine job even with damp or
wet materials. When conditions are
moist or damp, be sure to clean debris
off the machine regularly to keep cutting
efficiency high. And watch your footing!
Trimming/Mowing Quick Reference Chart
This Quick Reference Chart is provided as a general reference. Experiment
with your unit to determine the best settings for the conditions.
Cutting
Height
(Note 1)
Line
Diameter
(Notes 2 & 6)
Throttle
Speed
Walking
Speed
CONDITION
Light Growth
NOTES:
1. See “Adjust Line Cutting
Height.”
2. See “Use Correct
Diameter Trimmer Line.”
3. See “Vary Throttle Setting
For Conditions.”
4. See “Use Correct Walking
Speed.”
(Note 3)
(Note 4)
Any
.130" or .155"
.130" or .155"
Fast
Fast
Any
Start high,
progressively
lower
Tall Growth
Slow Pace
Heavy/Tough
Growth
5. See “Tips for Precision
Cutting.”
Any
.155"
Fast
Slow Pace
Slow Pace
6. See “Changing Trimmer
Lines” in Section 5.
7. Lighter line helps prevent
damage to bark of trees
and shrubs.
Trimming
Near Trees
.130"
(Note 7)
Any
Slow
and Shrubs
(Note 5)
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Section
Maintenance
5
ADJUSTING TRIMMER HEAD
ENGAGEMENT
The tension on the drive belt must be
correct for proper operation of the trim-
mer head. If the tension is correct, the
trimmer head will rotate when the
Trimmer Head Control Bail is pulled back
against the handlebar.
WARNING
Before inspecting, cleaning or servicing the machine, shut off engine, discon-
nect spark plug wire, and make sure that all moving parts have come to a com-
plete stop. Remove ignition key on electric start models.
Failure to follow these instructions can result in personal injury or property
damage.
NOTE: LEFT and RIGHT sides of unit are as
viewed from operator’s position behind the
handlebars.
A loose or worn drive belt causes the
trimmer head to move slowly, or not at
all, when the control bail is engaged (belt
squealing may also be noticeable).
REQUIRED MAINTENANCE SCHEDULE
If the belt tension is too tight, the trimmer
head may rotate before the control bail is
engaged, or when there is no free play in
the control bail.
BEFORE EVERY EVERY EVERY
EACH 25 100
USE HOURS HOURS HOURS
AS
NOTED
REQUIRED MAINTENANCE
5
Check engine oil level
•
•
•
•
•
•
Belt Tension Adjustment
1. Stop the engine and wait for all parts
to stop moving. Disconnect spark plug
wire and move it away from spark plug.
Remove ignition key on electric start
models.
Check trimmer lines
Check trimmer head engagement
Clean machine
1
3
Check nuts and bolts
Change engine oil
2. Adjust the positions of the two jam
nuts on the control cable adjuster (see
Figure 5-2) as described below:
•
•
•
•
2, 5
5
Service air filter system
Clean under mower deck
General lubrication
• To tighten belt tension:
Move the upper nut (A, Figure 5-2)
upward one or two full turns, then
move the lower nut (B) upward.
Tighten both nuts securely. Test unit
and readjust jam nuts as needed.
Inspect drive belt
•
Clean engine
•
4
6
• To loosen belt tension:
Move the lower nut (B, Figure 5-2)
downward one or two full turns, then
move the upper nut (A) down.
Tighten both nuts securely. Test the
unit and readjust jam nuts as
needed.
Check wear cup
•
Chart 5-1
NOTE 1 – New line replacement is suggested when old line is 50% or less of original length.
NOTE 2 – Change oil after first two hours of new operation; thereafter every 25 hours.
NOTE 3 – Clean daily if used in extremely dusty/dirty conditions (see engine manual).
NOTE 4 – Clean before using machine, and at each fuel refill.
NOTE 5 – Service more often if used in extremely dusty or dirty conditions (see engine manual).
NOTE 6 – Replace when severe gouges exist on bottom surface.
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
11
Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to
a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric
start models.
WARNING
Failure to follow these instructions can result in serious personal injury or property damage.
Belt Removal
1. Stop the engine and wait for engine to
cool. Disconnect the spark plug wire and
C
A
move it away from the spark plug.
Remove the ignition key on electric start
models.
B
2. Remove gasoline from fuel tank.
B
DANGER
A
GASOLINE IS HIGHLY FLAMMABLE AND
ITS VAPORS ARE EXPLOSIVE.
D
• Drain fuel into approved container
outdoors, away from open flame.
Figure 5-2: Belt tension adjustment.
F
E
• Be sure engine and muffler are cool
before draining gasoline.
• Do not smoke.
REMOVING AND REPLACING
TRIMMER HEAD
Failure to comply can result in serious
personal injury and property damage.
Figure 5-3
1. Stop the engine and wait for all mov-
ing parts to stop. Disconnect spark plug
wire and move it away from the spark
plug. Remove the ignition key on electric
start models.
3. Carefully tip unit on its left side and
secure it in place.
INSPECTING/REPLACING
DRIVE BELT
The drive belt should not require inspec-
tion for many hours of operation. If re-
placement becomes necessary, follow the
instructions given here.
4. Remove the plastic plug (A, Figure 5-
4) from the top of the mower deck.
2. Two bolts (A, Figure 5-3) secure the
trimmer head (B) to the spindle head (C).
Loosen both bolts (not the nuts) just
enough to open up the trimmer head and
allow it to slide down the spindle head
and past the two stops. Do not attempt
to remove the bolts completely – they are
permanently attached.
5. Using a 3/4" socket wrench, remove
nut (B, Figure 5-4), belleville washer (C)
and flat washer (D) from spindle shaft (E).
Belt Inspection
1. Stop the engine and let all moving
parts stop. Disconnect spark plug wire
and move it away from spark plug. Allow
engine to cool. Remove the key on elec-
tric start models.
A
B
C
D
NOTE: It may be necessary to first re-
move the wear cup (D, Figure 5-3) when
removing the trimmer head. See Step 4
for the procedure.
2. For convenience, we recommend that
you place the unit on a raised platform to
make access to the underside of the deck
as easy as possible.
E
3. Install the new trimmer head on the
spindle head. Tighten the hardware se-
curely (to 75 in/lbs.) and evenly.
3. Examine the belt. Feed it around the
rear (engine) pulley so the entire belt can
be examined. If cracks or other damage
are noted, a new belt is needed.
4. If the wear cup (D, Figure 5-3) is also
worn, replace it. Use a 1/2" socket
wrench to remove the screw (E, Figure 5-
3) and washer (F). Install the new wear
cup and reinstall the washer and screw.
Tighten the screw securely.
Figure 5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Section 5: Maintenance
Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to
a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric
start models.
WARNING
Failure to follow these instructions can result in serious personal injury or property damage.
6. Thread nut (B, Figure 5-4) a few turns
back onto spindle shaft (E) to protect the
threads on the spindle shaft during the
next step.
3. Securely tighten the mounting nut (G,
Figure 5-6) and screw in the idler pulley (I).
4. Securely tighten the idler arm mount-
ing screw (S, Figure 5-6). After tighten-
ing, check that idler arm is free to rotate.
If not, remove idler arm and check for de-
bris that may be interfering with freedom
of movement.
P
E
7. Loosen the spindle shaft by placing a
wood block against the top of the nut (B,
Figure 5-4) and firmly striking the wood
block with a hammer.
F
8. Remove the nut from the spindle shaft
and then remove the spindle shaft (E,
Figure 5-5) and entire spindle head as-
sembly (F) from the bottom of the deck.
Slip the belt off the spindle head pulley (P).
5. Look at the spindle head mounting
hole (O, Figure 5-6) and note the grooves
that are cut into the inner sides of the
hole. These grooves were formed by the
splines on the spindle shaft (E, Figure 5-5).
Figure 5-5
9. Disconnect the idler arm spring (R,
Figure 5-6) from the hole in the idler arm (T).
K
T
R
N
10. Using a 1/2" wrench, loosen the idler
arm mounting screw (S, Figure 5-6) two
full turns.
O
11. Using a 9/16" wrench and a 7/32" hex
(Allen) wrench, loosen the mounting nut
(G, Figure 5-6) and screw on the idler
pulley (I) a few turns, or until belt is free
to slip out between pulley and belt guide
(J). Remove belt.
S
L
J
12. Loosen rear belt guide screw (K,
Figure 5-6) enough to allow belt to be re-
moved from engine pulley (L). Remove
belt from unit.
N
M
G
I
Figure 5-6
Belt Replacement
8. Reinstall the flat washer (D, Figure 5-
4), belleville washer (C) and nut (B) on
the spindle shaft. Note that the dished-in
side of the belleville washer must face the
flat washer. Tighten the nut securely
(torque to 50 ft./lbs.), while checking fre-
quently to ensure that the spindle head
rotates freely. If the spindle head binds,
it could be due to the belt being pinched
between the spindle head and the belt
guides. If so, remove the spindle head
assembly and repeat steps 5-7.
6. Install the belt on the spindle head
pulley (P, Figure 5-5) and insert the spin-
dle shaft (E) (with attached spindle head
assembly) into the spindle head mount-
ing hole (O, Figure 5-6). Rotate the spin-
dle head assembly to align the splines on
the spindle shaft with the grooves in the
mounting hole. Check that the belt is still
in the pulley groove and is to the inside of
the die-cast belt guides (N, Figure 5-6).
1. Install belt on engine pulley (L, Figure
5-6) and retighten rear belt guide screw
(K) securely.
2. Route belt between idler pulley (I,
Figure 5-6) and belt guide (J), to inside of
brake arm (M), and next to die-cast belt
guides (N).
7. Using a firm push on the spindle head
assembly (Figure 5-6A), seat the spindle
head assembly into the hole. Check that
the threaded end of the spindle shaft is
protruding through the bottom of the
hole.
9. Replace plastic plug (A, Figure 5-4).
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
13
Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to
a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric
start models.
WARNING
Failure to follow these instructions can result in serious personal injury or property damage.
LUBRICATION
CLEANING THE ENGINE
Applying light oil or a silicone-based lu-
bricant to your machine allows parts to
work more smoothly and protects them
from the elements. Use Silicone-base
Spray Lubricant (or light oil) to lubricate
the following parts:
Before each use of the machine and at
each refueling, clean grass, chaff or accu-
mulated debris from the finger guard area
on top of the engine (see Figure 5-7), and
from the linkage, springs and controls on
the engine. Keep the area around and be-
hind the muffler free of any combustible
debris. See “Cleaning Debris” in the
engine manual for complete cleaning in-
structions. Do not use water to clean
engine parts as water could contaminate
the fuel system. Use a brush or dry
cloth. Be sure engine is cool before
cleaning around muffler area.
• Throttle control cable
• Control bail cable
• Nuts, bolts and other hardware
NOTE: The spindle head is permanently
lubricated at the factory. There is no
need for additional lubrication.
Figure 5-6A
10. Reattach the idler arm spring (R,
Figure 5-6) in the hole in the idler arm (T).
COMPACT STORAGE
NOTE: The separate engine air cleaner
must also be serviced according to the
instructions in the engine manual.
For compact storage of the unit, remove
the two screws and locknuts securing the
handlebar and carefully (to avoid kinking
the cables) rotate the handlebar so that
the upper portion rests on the engine and
the handlebar legs face to the rear of the
unit.
11. A new belt may need to be adjusted
by following the “Adjusting Trimmer
Head Engagement” instructions in this
Section.
WARNING
Engine parts must be kept clean to re-
duce the risk of overheating and ignition
of accumulated debris. This is espe-
cially important if cutting tall grass.
Clean accumulated debris at each refu-
eling and before each use of machine.
TRIMMER/MOWER CLEANING
AND DEBRIS REMOVAL
GENERAL ENGINE MAINTENANCE
Thorough and regular cleaning of debris
from the engine and the machine is re-
quired for maximum efficiency and good
overall performance. Inspect and clean
the following areas regularly, making
sure the engine is stopped, and cool, be-
fore proceeding:
Perform the following engine mainte-
nance for your engine according to the
engine maintenance schedule and in-
structions in the separate engine manual:
Failure to comply can cause injury or
property damage.
Engine Oil Service
• Brush and wipe off all engine surfaces,
especially before checking oil or adding
fuel. Do not let debris, oil or grease ac-
cumulate. To access the front of the
engine, lift the debris shield up and tilt it
forward.
Check the engine oil level before starting
the engine each day and check it after
each 5 hours of continuous operation.
Running the engine when it is low on oil
will quickly ruin the engine.
Finger Guard
Change the oil after every 25 hours of op-
eration and even sooner when operating
in extremely dirty or dusty conditions.
• Wipe the deck clean, particularly near
the engine muffler.
• Clean the underside of the deck.
Air Cleaner Service
• Keep safety and operating decals clean
Operating the engine with a dirty, clogged
air filter can cause poor performance and
damage to the engine. Inspect and ser-
vice the air cleaner after every 25 operat-
ing hours, more often if operating in very
dusty or dirty conditions. Never operate
the engine without the air cleaner
installed.
and legible.
Figure 5-7
• Keep all operating control levers
debris-free so they work properly.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Section 5: Maintenance
Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to
a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric
start models.
WARNING
Failure to follow these instructions can result in serious personal injury or property damage.
Spark Plug Service
OFF-SEASON STORAGE
Inspect and clean or replace the spark
plug after every 100 operating hours or
annually.
• Perform recommended engine mainte-
nance by following the engine storage
instructions found in the engine manual.
Be sure to protect the fuel lines, carbure-
tor and fuel tank from gum deposits by
removing fuel or by treating fuel with a
fuel stabilizer (follow the engine manu-
facturer’s recommendations).
When storing the unit for extended peri-
ods, follow these procedures to ensure
that the unit will be in good condition for
future use.
Spark Arrester Screen Service
If the engine is equipped with a spark ar-
rester screen, remove and clean it ac-
cording to the time intervals and instruc-
tions in the engine manual.
WARNING
• Never perform maintenance when en-
gine is running or spark plug wire is
connected, except when instructed to
do so.
• Clean any dirt, grass or chaff from the
air cooling system intake area and other
parts of the engine.
Engine Cleaning
The engine must be kept clean to assure
smooth operation and to reduce the risk
of overheating and ignition of accumu-
lated debris.
• Never store mower with fuel in fuel
tank inside a building where fumes
can reach an open flame or spark, or
where ignition sources are present
such as hot water and space heaters,
furnaces, clothes dryers, stoves, elec-
tric motors, etc. Make sure engine is
cool before storing.
• Disconnect spark plug wire and move
away from spark plug.
Carburetor/Governor Control
Adjustments
The carburetor was adjusted at the fac-
tory for best operating speed. Refer to
the engine manual for any adjustment
information.
• Drain gasoline outdoors into an
approved container.Do not smoke and
keep fuel away from open flame.
The governor controls the maximum safe
operating speed and protects the engine
and other moving parts from damage
caused by overspeeding. Do not tamper
with the governor settings. Seek autho-
rized service if you think an adjustment is
required.
Failure to follow these instructions will
result in serious personal injury or
property damage.
• Store machine on a level surface.
• Inspect for any loose, broken or miss-
ing parts. Repair or replace parts as
necessary.
Throttle Control Adjustment
If the engine does not shut off when the
throttle lever is moved to the stop posi-
tion, or if the engine does not respond to
various throttle settings, refer to the en-
gine manual for service information.
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
15
Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to
a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric
start models.
WARNING
Failure to follow these instructions can result in serious personal injury or property damage.
CHANGING TRIMMER LINES
WARNING
When trimmer lines wear, it takes longer
to complete mowing and trimming pro-
jects. A good rule of thumb is to change
the lines when they reach half their origi-
nal length.
Offsetting the trimmer lines causes the lines to rotate faster than when they project
an equal length on each side. This increases the chance of loose materials being
dislodged and propelled at high speeds.
Failure of the operator to wear safety goggles and appropriate clothing and to keep
bystanders away can result in severe personal injury or property damage.
Use the extra-heavy duty (.155" diameter)
line when cutting thick, tough growth.
Use the thinner (.130" diameter) line for
less demanding conditions and for use
near trees or shrubs to help prevent
girdling (cutting of bark).
Figure 5-8: Use this single line,
easy-loop pattern for all but the
more difficult cutting conditions.
To Change Trimmer Lines:
1. Stop engine, allow all parts to stop
moving and then disconnect the spark
plug wire. Remove the ignition key on
electric start models. DO NOT touch the
metal wear cup on the bottom of the
spindle head—it may be hot.
NOTE: The two line holders on the trim-
mer head are permanently secured. Do
not attempt to remove the line holders.
Figure 5-9: If lines tend to
Reverse Loop
loosen (especially in more diffi-
cult cutting conditions), add a
single reverse loop and then
readjust line so that ends are
even. This pattern results in a
slightly narrower cutting swath.
2. If necessary, you may tip the unit
back slightly when changing lines.
However, do not tip the unit all the way
back as motor oil may flow to the exhaust
area and the engine may smoke for sev-
eral seconds when started.
3. Three different line installation pat-
terns are available, as shown in Figures
5-8, 5-9 and 5-10.
Figure 5-10: For more difficult
cutting conditions, use two of the
thicker (.155" diameter) lines in
each line holder. Follow the
pattern shown in Figure 5-8.
4. Feed the line through the loops of the
line holder as shown.
• An equal amount of line should project
out from each side of the line holder,
creating an overall 22" wide cutting
swath.
• You may offset both trimmer lines
somewhat to increase the cutting swath
up to 25" wide. However, DO NOT off-
set the line so that the overall cutting
swath is greater than 25". See Warning
statement at right.
• Whether replacing one or both lines,
they must both be .130" or .155" in
diameter.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Section 5: Maintenance
Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to
a stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric
start models.
WARNING
Failure to follow these instructions can result in serious personal injury or property damage.
TROUBLESHOOTING
Before performing any of the corrections in this Troubleshooting Chart, refer to the appropriate information contained in this
Manual or the Engine Owner’s Manual for the correct safety precautions and servicing procedures. Contact your local autho-
rized Engine Service Dealer for engine service. Contact your local authorized dealer for service problems with the machine.
PROBLEM
POSSIBLE CAUSE
CORRECTION
Engine does not start.
1. Spark plug wire disconnected.
2. Defective or incorrectly gapped spark plug.
3. Fuel tank empty.
1. Reconnect wire.
2. Inspect/replace spark plug.
3. Add fuel.
4. Dirty carburetor or fuel line.
5. Dirty air cleaner.
6. Carburetor out of adjustment.
7. Engine flooded.
8. Engine Throttle Lever in incorrect position.
9. Stale gasoline.
10. Defective Engine Throttle Lever.
11. Dirt or water in fuel tank.
4. Clean carburetor or fuel line.
5. Clean or replace.
6. Adjust carburetor. See Engine Service Dealer.
7. Wait several minutes before starting.
8. Move Throttle Lever to FAST position.
9. Drain old fuel and add fresh fuel.
10. See Engine Service Dealer.
11. See Engine Service Dealer.
Engine runs poorly.
1. Bad spark plug.
2. Dirty air filter.
1. Inspect/replace spark plug.
2. Clean or replace.
3. Carburetor out of adjustment.
4. Stale fuel.
5. Dirt or water in fuel tank.
6. Engine cooling system clogged.
3. Adjust carburetor. See Engine Service Dealer.
4. Drain and replace fuel.
5. See Engine Service Dealer.
6. Clean fins.
Engine overheats.
1. Engine cooling system clogged.
2. Carburetor out of adjustment.
1. Clean air cooling areas and behind debris shield.
2. Adjust Carburetor. See Engine Service Dealer.
Engine does not shut off.
Throttle control misadjusted.
See Engine Service Dealer.
.
Poor mowing performance.
1. Line length is too short or too long.
1. Adjust line length to 18" long. When less
than 1/2 this length, replace the line.
2. Adjust cutting height to approximately 1/3
of the length of the grass.
2. Cutting height is too high or low for height
of grass being cut.
3. Engine not set at FAST speed.
3. Move Engine Throttle Lever to FAST (Rabbit).
Machine vibrates.
1. Trimming head mounting bolt loose.
2. Line lengths are substantially different.
3. Loose nuts or bolts.
1. Tighten bolt.
2. Adjust lines to approximately equal lengths.
3. Check all bolts and nuts, including engine
bolts.
4. Broken spindle head or trimmer head.
Incorrect line installation.
4. Replace broken part.
Trimmer head does not
retain line.
See “Changing Trimmer Lines” in Section 5.
Trimmer Head does not
retain height setting.
1. Head bolts may be loose.
2. Head is worn.
1. Tighten head bolts to 75 in/lbs.
2. Replace head assembly.
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List 17
Model 52067
DRAWING NO. 1
1
2
7
3
4
9
5
6
10
11
8
6
5
5
5
14
13
12
PARTS LIST – DRAWING NO. 1
15
14
5
Ref. # Part #
Description
Qty.
17
17
1
2
3
1917765
1918116
1915290
Debris Guard ............................................ 1
Decal-Logo ............................................... 1
Push-in Fastener....................................... 5
17
16
19
4
1917407001 Debris Guard Support............................... 1
5
6
7
8
1754128
1915320
*
1904511
1917727
1100243
1100009
1918227
1918115
Hex Flange Screw, 1/4-20 x 3/4................ 8
Spacer ...................................................... 2
Engine....................................................... 1
Decal-Hot Surface Warning ...................... 1
Engine Pulley............................................ 1
Spring Lock Washer ................................. 1
Hex Hd. Screw, 3/8-24 x 1, Grade 5 ......... 1
Deck (Incl. Ref. 13)................................... 1
Decal-Warning.......................................... 1
5
9
10
11
12
13
14
15
16
17
18
19
18
1917144001 Hood Bracket............................................ 2
1186389
1917574
1768194
1917154
1917155
Flange Lock Nut, 1/4-20 ........................... 2
Belt Guide................................................. 1
Hex Hd. Screw, 3/8-16 x 1-1/2 ................. 3
Deflector Flap............................................ 1
Rod........................................................... 1
Order parts from your local authorized engine dealer. Refer to engine
for model/type/code number.
*
Download from Www.Somanuals.com. All Manuals Search And Download.
18 Parts List
Model 52067
DRAWING NO. 2
1
2
See DRAWING
NO. 3
3
7
5
8
9
6
10
1
4
5
3
See DRAWING
NO. 1
19
18
11
20
18
2
12
23
21
22
24
13
25
14
26
15
See ACCESSORIES
AND KITS
27
16
17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List 19
Model 52067
PARTS LIST – DRAWING NO. 2
Ref. # Part #
Description
Qty.
Ref. # Part #
Description
Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1917592
1917593
1917775
1917258
1724491
1918069
1917588
1734514
9928
1917745
1917579
1918246
1917581
1918329
Wheel/Tire Assembly..............................
Locking Retaining Ring ..........................
Flat Washer ............................................
Axle........................................................
Self-Tap Screw, 5/16-18 x 3/4 ...............
Self-Tap Screw, 5/16-18 x 2...................
Cap Plug.................................................
Hex Lock Nut, 1/2-13 .............................
Belleville Washer....................................
Hardened Washer...................................
V-Belt .....................................................
Spindle Head Adapter (Incl. Bearing) .....
Spindle Shaft..........................................
Spindle Head Assembly (Incl. Bearing,
Insert, and Refs. 16, 17, 18).................
2
2
2
1
2
2
2
1
1
1
1
1
1
15
16
17
18
19
20
21
22
23
24
25
26
27
1918393
Trimmer Head Assembly (Incl. Ref. 27) .
1
1915220001 Wear Cup ...............................................
1
1
3
1
1
1
1
1
1
1
1
1
1917599
1724491
1917573
1910849
1917746
1917589
1910857
1917572
1910855
1186393
1918332
Square Washer.......................................
Self-Tap Screw, 5/16-18 x 3/4................
Cable Bracket .........................................
Idler Spring ............................................
Flat Washer ............................................
Control Cable - Trimmer Head ...............
Button Hd. Screw, 3/8-16 x 1-1/2...........
Idler Arm................................................
Idler Pulley .............................................
Flange Lock Nut, 3/8-16.........................
Rubber Shim Kit (2 shims per kit)..........
1
Download from Www.Somanuals.com. All Manuals Search And Download.
20 Parts List
Model 52067
DRAWING NO. 3
4
1
11
2
6
10
12
3
6
5
7
9
8
13
14
PARTS LIST – DRAWING NO. 3
13
Ref. # Part #
Description
Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1918283
1915889
1918304
Upper Handlebar (Incl. Refs. 2 & 3).......
Decal–Bail Engage/Disengage ................
Decal–Throttle .......................................
1
1
1
1
1
2
1
1
1
1
1
1
3
2
1
2
14
1918070001 Control Bail–Trimmer Head ...................
1917589
1908677
Cable Assembly–Trimmer Head .............
Bushing..................................................
1749977001 Cable Bracket .........................................
1983658
1185814
1918081
1100807
1110106
1763682
1100799
Hex Hd. Screw, 1/4-20 x 1-1/8...............
Hex Flange Lock Nut, 1/4-20..................
Throttle Lever & Cable Assembly ...........
Hex Hd. Screw, 1/4-20 x 2 .....................
Hex Lock Nut, 1/4-20 .............................
Cable Tie.................................................
Hex Hd. Screw, 5/16-18 x 1-1/2.............
16
15
1917145001 Lower Handlebar ...................................
1732499 Hex Lock Nut, 5/16-18 ...........................
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List 21
Model 52067
ACCESSORIES AND KITS
Ref. # Part #
Description
Qty.
1
2
1904476
1904477
Trimmer String Kit, .155" dia. line
(includes 24 pieces)................................ N/I
Trimmer String Kit, .130" dia. line
(includes 24 pieces)................................ N/I
N/I Not included with unit, order separately
2
1
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER SERVICE INFORMATION
Owner Registration Card
Customer Service and Technical Service
Please fill out and mail the enclosed owner
registration card. The purpose of this card is
to register each unit at the factory so that we
can provide you with warranty benefits and in-
formational bulletins.
If you have questions or problems with the
unit, contact your local dealer or the factory.
(When calling or writing, provide the
Model/Serial Numbers of the unit.)
MAIL
MAIL
Replacement Parts
Warranty Service
Factory specified replacement parts are
available from your authorized dealer or di-
rectly from the factory. When ordering
parts, be sure to provide the following:
The warranty statement is included in the unit’s literature
package.
Model/Serial Numbers
• Model/Serial Numbers of the unit.
• Part number of the part needed.
• Part Description.
A Model/Serial Numbers decal is located on the left side of
the unit. For ready reference, record these numbers in the
spaces below.
Date of Purchase:
Model Number:
Serial Number:
• Quantity needed.
NOTE: All replacement parts must conform to our rigid quality
specifications. Although some replacement parts we provide
may vary slightly in shape, color or texture from the original
parts, any variations will not affect the fit or performance of
these parts on your unit.
Authorized Dealer Information
If you purchased your unit from an authorized dealer, record
the dealer’s address and phone number below for ready
reference:
Engine Service and Repair
Dealer Name:
Address:
For engine service or repair, contact your
nearest authorized engine dealer (look in
the Yellow Pages under
Phone:
“Engines–Gasoline”). The engine is war-
ranted by the engine manufacturer. Any
unauthorized work performed on the engine during the war-
ranty period may void this warranty. For complete details on
the engine warranty, refer to the engine owner manual.
IMPORTANT:
Left and right sides of the unit are determined by standing
behind the unit, in the operator’s position, and facing in the
direction of forward travel.
WARNING
NOTICE:
We urge using only genuine replacement parts, which
meet all the latest requirements. Replacement parts
manufactured by others could present safety hazards,
even though they may fit on the unit.
We reserve the right to change specifications, add im-
provements or discontinue the manufacture of any of our
equipment without notice or obligation to purchasers of our
equipment.
For customer assistance, contact your nearest authorized dealer or:
GARDEN WAY INCORPORATED • 1 Garden Way • Troy, New York 12180
Customer Service: 1-800-437-8686 • Technical Service: 1-800-520-5520 • Parts Service: 1-800-648-6776
Outside the United States and Canada:
Customer Service: (518) 233-4807 • Technical Service: (518) 233-4808 • Parts Service: (518) 233-4806 • FAX (518) 233-4622
1905694 (6/01)
Printed in U.S.A.
© 2001 Garden Way Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
|