Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR’S MANUAL
Model 24A-425E766 Shown
Chipper Shredder — Model Series 410 & 420
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
FORM NO. 769-00830C
6/01/2006
PRINTED IN U.S.A.
TROY BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Download from Www.Somanuals.com. All Manuals Search And Download.
$!.'%2
s
s
s
2EAD THE OPERATORgS MANUALꢅS BEFORE STARTING AND USING UNITꢀ
+EEP ALL SHIELDS AND GUARDS IN PLACE AND SECURELY ATTACHEDꢀ
+EEP HANDSꢆ FEETꢆ FACEꢆ CLOTHING AND LONG HAIR OUT OF 3HREDDER
(OPPERꢆ #HIPPER #HUTE AND $ISCHARGE #HUTE WHILE THE ENGINE IS
RUNNINGꢀ 2OTATING CUTTING BLADES INSIDE THESE OPENINGS WILL CAUSE
s
s
$O NOT OPERATE ON PAVEMENTꢆ GRAVEL OR OTHER HARD SURFACES
SINCE OBJECTS CAN RICOCHET AND CAUSE INJURYꢀ
s
)F THE CHIPPER SHREDDER JAMS OR BECOMES CLOGGEDꢆ REFER TO OPERATORgS
MANUAL ON CLEARING BLOCKAGEꢀ
A
s
)F ENGINE STALLS BECAUSE OF JAMꢆ MOVE THROTTLE CONTROL LEVER TO STOP
POSITION OR SHUTꢇOFF ROCKER SWITCH TO ꢈ/ꢈ /&& IF EQUIPPEDꢆ BEFORE
4O AVOID
A
FIRE HAZARDꢆ KEEP LEAVESꢆ GRASSꢆ AND OTHER
$O ./4 PLACE BRANCHES OVER ꢄꢅꢆ
INCH DIAMETER INTO THE LAR GE
3HREDDER (OPPERꢃ "RANCHES OVER ꢄꢅꢆ
INCH IN DIAMETER SHOULD BE PLACED IN
THE 3MALL #HIPPER #HUTEꢃ
COMBUSTIBLE MATERIALS AWAY FROM HOT ENGINE AND MUFFLERꢀ
+EEP CHILDREN AND OTHERS AWAY FROM AREA OF OPERATIONꢀ
7EAR APPROVED SAFETY GLASSESꢆ GLOVES AND EAR PROTECTIONꢀ
CLEARINGꢀ
s
s
1
s
$O NOT INSTALL REMOVEꢆ ADJUSTꢆ OR SERVICE THE DISCHARGE SCREEN OR ANY
OTHER PART WHILE THE ENGINE IS RUNNINGꢀ "LADE CONTACT CAN OCCURꢀ
SERIOUS PERSONAL INJURY IF CONTACTEDꢀ -ATERIAL BEING PROCESSED MAY
BOUNCE BACK FROM INLET OPENINGS OR BE THROWN FROM THE DISCHARGE CHUTEꢀ
,ONG HAIR OR LOOSE CLOTHING MAY BE PULLED OR SUCKED INTO THE INLET
OPENINGSꢀ
s
s
$O NOT OPERATE ON UNEVEN GROUND WHERE UNIT IS UNSTABLEꢀ
$O NOT OPERATE WITH #HIPPER #HUTE IN UP POSITIONꢀ ,ATCHED UP IS FOR
-ATERIAL FEED INTO HOPPER
SHOULD BE METERED AS
ꢉꢊꢃꢈ
STORAGE ONLYꢀ 5NLATCHꢆ LOWER AND LOCK #HIPPER #HUTE IN PLACE BEFORE
OPERATING MACHINEꢀ
INSTRUCTED IN OPERATORgS
MANUAL TO AVOID CLOGGINGꢃ
Safety
Labels
().'%$ 500%2 #()00%2 #(54%ꢀ
34/2!'% 4O SAVE SPACEꢂ #HUTE MAY BE
UNꢁLOCKED AND LATCHED IN THE RAISED POSITIONꢃ
/0%2!4)/. #HUTE MUST BE IN THE LOWERED AND
LOCKED POSITIONꢃ 2EFER TO
OPERATORgS MANUAL FOR PROPER
USE OF THE #HIPPERꢃ
$!.'%2
2/4!4).' #544).' ",!$%3ꢀ
+%%0 (!.$3 !.$ &%%4 /54
/& /0%.).'3 7(),% -!#().%
)3 25..).'ꢀ
ꢁ
ꢁ
3TORAGE ONLY
/PERATING POSITION
WARNING
$!.'%2
s 2/4!4).' #544).' ",!$%3ꢀ+%%0 (!.$3
!.$ &%%4 /54 /& /0%.).' 7(),%
-!#().% )3 25..).'ꢀ
$!.'%2
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
2/4!4).' #544).' ",!$%3ꢀ
s $/ ./4 /0%2!4% 4()3 -!#().% 5.,%33
4(% #(54% $%&,%#4/2 (!3 "%%.
02/0%2,9 ).34!,,%$ !.$ )3 3%#52%$
7)4( 4(% (!.$ +./"3ꢀ
+%%0 (!.$3 !.$ &%%4 /54
/& /0%.).'3 7(),% -!#().%
)3 25..).'ꢀ
7!2.).'
manual before at-
s $O NOT TRANSPORT MACHINE WHILE
ENGINE IS RUNNINGꢀ
s $O NOT ALLOW ANYONE TO SIT OR RIDE ON
SHREDDERꢀ
tempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
s 3HREDDER SHOULD NOT BE TOWED ON ANY s $O NOT TOW SHREDDER FOR LONG DISTANCESꢀ
STREETꢁ HIGHWAY OR PUBLIC ROADꢀ
s $O NOT TOW SHREDDER OVER ꢂꢃ MꢀPꢀHꢀ
s "EFORE TOWINGꢁ BE CERTAIN THE SHREDDER
IS CORRECTLY ATTACHED TO TOWING VEHICLEꢀ
3ꢁꢂꢃꢃꢄ
$/ ./4 /0%2!4% 4()3 -!#().%
5.,%33 4(% #(54% $%&,%#4/2
(!3 "%%. 02/0%2,9 ).34!,,%$ꢃ
HEED ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo-
nents contain or emit chemicals known to State of California to cause cancer and
birth defects or other reproductive harm.
2
DANGER: This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Safe
Operation Failure to observe the following safety instructions could result in serious injury or death.
Training
Preparation
1. Read, understand, and follow all instructions on the ma-
chine and in the manual(s) before attempting to assemble
and operate. Keep this manual in a safe place for future
and regular reference and for ordering replacement parts.
2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.
1. Thoroughly inspect the area where the equipment is to
be used. Remove all rocks, bottles, cans, or other foreign
objects which could be picked up or thrown and cause
personal injury or damage to the machine.
2. Always wear safety glasses or safety goggles during opera-
tion or while performing an adjustment or repair, to protect
eyes. Thrown objects which ricochet can cause serious
injury to the eyes.
Practices
3. Never allow children under 16 years old to operate this
machine. Children 16 years old and over should read and
understand the operation instructions and safety rules in
this manual and should be trained and supervised by a
parent.
3. Wear sturdy, rough-soled work shoes and close-fitting
slacks and shirts. Loose fitting clothes or jewelry can be
caught in movable parts. Never operate this machine
in bare feet or sandals. Wear leather work gloves when
feeding material in the chipper chute.
WARNING
4. Never allow adults to operate this machine without proper
instruction.
4. Before starting, check all bolts and screws for proper tight-
ness to be sure the machine is in safe working condition.
Also, visually inspect machine for any damage at frequent
intervals.
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
5. Keep bystanders, helpers, pets, and children at least
75 feet from the machine while it is in operation. Stop
machine if anyone enters the area.
5. Maintain or replace safety and instructions labels, as
necessary.
6. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.
6. To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive. Serious personal injury can
occur when gasoline is spilled on yourself or your clothes
which can ignite. Wash your skin and change clothes
immediately.
7. Do not put hands and feet near rotating parts or in the
feeding chambers and discharge opening. Contact with
the rotating impeller can amputate fingers, hands, and
feet.
8. Never attempt to unclog either the feed intake or
discharge opening, remove or empty bag, or inspect and
repair the machine while the engine is running. Shut the
engine off and wait until all moving parts have come to a
complete stop. Disconnect the spark plug wire and ground
it against the engine.
manual before at-
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
tempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is hot
or running.
e. Allow engine to cool at least two minutes before refuel-
ing.
f. Never over fill fuel tank. Fill tank to no more than 1/2
inch below bottom of filler neck to provide space for fuel
expansion.
HEED ITS WARNING!
Your Responsibility
Restrict the use
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and equip-
ment. Move machine to another area. Wait 5 minutes
before starting the engine.
of this power machine
to persons who read,
understand
i. Never store the machine or fuel container inside where
there is an open flame, spark, or pilot light (e.g. furnace,
water heater, space heater, clothes dryer, etc.)
j. To reduce a fire hazard, keep machine free of grass,
leaves, or other debris build-up. Clean up oil or fuel
spillage and remove any fuel soaked debris.
k. Allow machine to cool at least 5 minutes before storing.
and follow the warnings
and instructions
in this manual
and on the machine.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Maintenance & Storage
1. Do not put hands and feet near rotating parts or in the
feeding chambers and discharge opening. Contact with the
rotating impeller can amputate fingers, hands, and feet.
2. Before starting the machine, make sure the chipper chute,
feed intake, and cutting chamber are empty and free of all
debris.
1. Never tamper with safety devices. Check their proper
operation regularly.
2. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage and repair, if
needed.
2
3. Thoroughly inspect all material to be shredded and remove
any metal, rocks, bottles, cans, or other foreign objects
which could cause personal injury or damage to the
machine.
3. Before cleaning, repairing, or inspecting, stop the engine
and make certain the impeller and all moving parts have
stopped. Disconnect the spark plug wire and ground it
against the engine to prevent unintended starting.
4. Do not change the engine governor settings or overspeed
the engine. The governor controls the maximum safe
operating speed of the engine.
Safe
Operation
Practices
I4. f it becomes necessary to push material through the
shredder hopper, use a small diameter stick. Do not use
your hands or feet.
I5. f the impeller strikes a foreign object or if your machine
should start making an unusual noise or vibration,
immediately shut the engine off. Allow the impeller to come
to a complete stop. Disconnect the spark plug wire, ground
it against the engine and perform the following steps:
a. Inspect for damage.
5. Maintain or replace safety and instruction labels, as neces-
sary.
6. Follow this manual for safe loading, unloading, transporting,
and storage of this machine.
7. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer, etc.
b. Repair or replace any damaged parts.
c. Check for any loose parts and tighten to assure
continued safe operation.
8. Always refer to the operator’s manual for proper instructions
on off-season storage.
WARNING
6. Do not allow an accumulation of processed material to build 9. If the fuel tank has to be drained, do this outdoors.
up in the discharge area. This can prevent proper discharge
and result in kickback of material through the feed opening.
7. Do not attempt to shred or chip material larger than
specified on the machine or in this manual. Personal injury
or machine damage could result.
10. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
This symbol points
out important safety
instructions, which if
not followed, could
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way.Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
8. Never attempt to unclog either the feed intake or discharge
opening while the engine is running. Shut the engine off,
wait until all moving parts have stopped, disconnect the
spark plug wire and ground it against the engine before
clearing debris.
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
Notice regarding Emissions
9. Never operate without the shredder hopper, chipper chute,
or chute deflector properly attached to the machine. Never
empty or change discharge bag while the engine is running.
10. Keep all guards, deflectors and safety devices in place and
operating properly.
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and may
include the following emission control systems: Engine Modifica-
tion (EM) and Three Way Catalyst (TWC) if so equipped.
instructions in this man-
ual before attempting to
operate this machine.
Failure to comply with
these instructions may
result in personal injury.
When you see this
11. Keep your face and body back and to the side of the chipper
chute while feeding material into the machine to avoid
accidental kickback injuries.
Your Responsibility
Restrict the use of this power machine to persons who read, un-
derstand and follow the warnings and instructions in this manual
and on the machine.
12. Never operate this machine without good visibility or light.
13. Do not operate this machine on a paved, gravel or non-level
surface.
symbol.
HEED IT’S WARNING!
14. Do not operate this machine while under the influence of
alcohol or drugs.
15. Muffler and engine become hot and can cause a burn. Do
not touch.
Your Responsibility
Restrict the use
16. Never pick up or carry machine while the engine is running.
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: This Operators Manual covers a range of product
specifications for various models. Characteristics and
features discussed and/or illustrated in this manual may
not be applicable to all models. Troybilt LLC reserves the
right to change product specifications, designs and equip-
ment without notice and without incurring obligation.
A
3
IMPORTANT: This unit is shipped without gasoline or oil
in the engine. Be certain to service engine with gasoline
and oil as instructed in the separate engine manual
before operating your machine.
Setting Up
Your Chipper
Shredder
Loose Parts In Carton
a. Debris Collection Bag
b. Tow Bar
B
c. Safety Glasses
d. Engine Oil
Lowering The Chipper Chute
(Model 24A-424G766 & 24A-42ꢀE766 Only)
WARNING
1. For shipping reasons, the unit is crated with its chipper
chute in a raised position. To pivot it downward,
proceed as follows:
Figure 1
Never operate the
chipper shredder with
the chipper chute in
the raised position.
Doing so may result
in property damage
or serious injury
a. Pull the spring latch upward.
b. Gently pivot the chipper chute down
until it clicks into the lock rod. See Figure 1.
WARNING: Never operate the chipper shredder with
the chipper chute in the raised position. Doing so
may result in property damage or serious injury to
the operator or bystanders.
to the operator or
bystanders.
Attaching The Debris
Collection Bag
2. To attach the bag:
IMPORTANT
This unit is shipped
without gasoline or
oil in the engine. Be
certain to service
a. Place the opening of the bag completely over the
chute deflector.
Figure 2
b. Position the bag so that the wing knobs which
secure the chute deflector to the impeller housing
are completely covered.
engine with gasoline
and oil as instructed
in the separate engine
manual before operat-
ing your machine.
c. Pull on the drawstrap until the bag is tight around
chute deflector opening. See Figure 2.
Attaching The Tow Bar
3. To attach the tow bar:
a. Remove the spring pin and clevis pin from the end
of the tongue. See Figure 3.
NOTE: All references in
this manual to the left
or right side of the chip-
per shredder is from
the operating position
only. Exceptions, if any,
will be specified.
b. Insert the tongue into the base.
c. Reinsert the clevis pin through aligning holes in
both the tongue and the base. Fasten with the
spring pin to secure. See Figure 3.
A
C
B
Figure 3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
KnowYour Chipper Shredder
Hopper
3
Handle
Setting Up
Your Chipper
Shredder
Spring Latch
Chipper Chute
Chute
Deflector
WARNING
Starter Handle
Never operate the
chipper shredder with
the chipper chute in
the raised position.
Use the spring latch
to lower the chipper
chute into the operat-
ing position before
starting the engine.
Tow Bar
Model 24A-425E766 Shown
Lock Rod
Figure 4
Now that you have set up your chipper shredder for
operation, get aquainted with its controls and fea-
tures. These are described below and illustrated on
this page. This knowledge will allow you to use your
new equipment to its fullest potential.
WARNING: Never operate the chipper
shredder with the chipper chute in the
raised position. Use the spring latch
to lower the chipper chute into the
operating position before starting the
engine.
IMPORTANT
Never place branches
with a diameter greater
than 1/2-inch in the
hopper. Doing so
Chipper Chute
Lock Rod
Branches up to 3” in diameter may be fed into the
chipper chute for chipping. See Figure 4.
The lock rod is located on the chipper chute sup-
port. It is used to release or lock the chipper chute
in a lowered position for operation. See Figure 4.
Hopper
Leaves, twigs and branches up to 1/2-inch in diam-
eter may be placed into the hopper for shredding.
See Figure 4.
Tow Bar
Use the tow bar to tow the chipper shredder behind
a tractor to a job site. See Figure 4.
can result in serious
damage to your unit’s
shredder blade, flails or
impeller.
IMPORTANT: Never place branches with a diameter
greater than 1/2-inch in the hopper. Doing so can result
in serious damage to your unit’s shredder blade, flails or
impeller.
Handle
Use the handle when manually transporting the
chipper shredder. See Figure 4.
Starter Handle
The starter handle is located on the engine. Pull the
starter handle to start engine. See Figure 4.
Spring Latch
Engine Controls
The spring latch is located on the top of the hopper.
It is used to release or lock the chipper chute in a
raised position for storage or for transporting. See
Figure 4.
See the engine Owner/Operator manual packed
with your unit for the location and function of the
controls on the engine.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
This Operators Manual covers a range of product
specifications for various models. Characteristics and
features discussed and/or illustrated in this manual may
not be applicable to all models. Troy Bilt LLC reserves
the right to change product specifications, designs
and equipment without notice and without incurring
obligation.
engine reaches start of compression cycle (rope will
pull slightly harder at this point).
NOTE: A “clanking” noise may be heard when pulling
the starter rope. It is completely normal and does NOT
indicate a malfunction of any kind.
4
6. Pull rope with a rapid, continuous, full arm stroke.
Keep a firm grip on starter handle. Let rope rewind
slowly.
Operating
Your Chipper
Shredder
WARNING: The operation of any
chipper shredder can result in
foreign objects being thrown into the
eyes, which can damage your eyes
severely. Always wear the safety
7. Repeat the previous steps until engine starts. When
engine starts, move choke control gradually to RUN
position until the engine is running smoothly.
glasses provided with this unit or eye
shields before chipping or shredding
and while performing any adjustments
or repairs.
WARNING: Never run the engine indoors
or in a poorly ventilated area. Engine
exhaust contains carbon monoxide, an
odorless and deadly gas.
Gas and Oil Fill-Up
Stopping Engine
1. Move throttle control lever to STOP position (Model
414) or push rocker switch to OFF (Model 424 & 425).
See Figure 6.
Service the engine with gasoline and oil as instructed in
the separate engine manual packed with your chipper
shredder. Read instructions carefully.
WARNING
The operation of any
chipper shredder
WARNING: Never fill fuel tank indoors
with engine running or until the engine
has been allowed to cool for at least
two minutes after running.
NOTE: See your engine manual packed with your unit for
more detailed instructions.
can result in foreign
objects being thrown.
Always wear the safety
glasses provided with
this unit or eye shields
before chipping or
shredding and while
performing any adjust-
ments or repairs.
CAUTION: Never stop the engine by
moving the choke lever into the CHOKE
position. Backfire, fire or engine damage
could result.
Starting Engine
IMPORTANT: Because this manual covers several
different model units, different starting instructions may
apply to your particular engine. Some engines may have
a fuel petcock, some may not. Some engines may have
On/Off switches, other may not. Some units will utilize a
choke system, while others will require priming. These
factors depend on what make and model engine comes
with your particular unit. For these reasons, please refer
to the engine operator’s manual for the correct starting
procedure.
Never fill fuel tank
indoors with engine
running or until the
engine has been
allowed to cool for
at least two minutes
after running.
Basic Starting Procedure:
1. Attach spark plug wire to spark plug. Make certain
the metal cap on the end of the spark plug is
fastened securely over metal tip on the spark plug.
2. Open fuel shut-off valve (If equipped) and make sure
the On/Off switch is in the On position (if equipped).
Never run the engine
indoors or in a poorly
ventilated area. En-
gine exhaust contains
carbon monoxide, an
odorless and deadly
gas.
3. Move choke control lever to CHOKE position, if
equipped. If the unit has a primer, prime the motor as
instructed in the engine operator’s manual.
NOTE: A warm engine may not require choking or
priming.
4. Move throttle control lever to FAST position (if
equipped).
Never stop the engine
by moving the choke
lever into the CHOKE
position. Backfire,
fire or engine damage
could result.
5. Grasp starter handle and pull rope out slowly until
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating The Chipper Shredder
Shredding
Yard waste such as leaves and pine needles can be
placed in the hopper for shredding. After material has
been processed by the shredder blade and flails, it will be
forced out of the chute deflector, and, if attached, into a
debris collection bag.
4
Operating
Your Chipper
Shredder
Observe the following guidelines when shredding yard
debris:
1. Never attempt to shred material other than normal
yard debris (leaves, twigs, pine cones, etc.).
2. Avoid shredding fibrous plants such as tomato vines
until they are thoroughly dried out. Fresh vines do not
shred well and tend to wrap themselves around the
impeller and flails.
3. Place reasonable amounts of debris into the hopper at
a time. Do not overload the hopper.
Figure 7
4. Allow the material in the hopper to be drawn into
the blades and shredded before adding additional
debris to the hopper. Failure to due so may result in a
clogged hopper, clogged chute deflector or a stalled
engine.
Chipping
WARNING
WARNING: Never operate the chip-
per shredder without chipper chute
lowered into the operating position.
Never operate the chip-
per shredder without
chipper chute lowered
into the operating
position.
5. Avoid placing twigs longer than 24 inches into the
hopper. Twigs longer than 24 inches may result in a
clogged hopper.
Branches up to 3” in diameter can be fed into the
chipper chute. Observe the following guidelines when
chipping branches:
6. Never place branches with a diameter greater than
1/2-inch in the hopper. Doing so can result in serious
damage to the unit’s shredder blade, flails or impeller.
1. Keep both hands firmly on the branch as you feed it
into the chipper chute.
2. Never feed more than one branch into the chipper
chute at a time.
Clearing the Hopper
Should the hopper become clogged with debris during
operation, proceed as follows:
IMPORTANT
3. Never feed anything other than branches (or wood)
into the chipper chute.
Never place branches
with a diameter greater
than 1/2-inch in the hop-
per. Doing so can result
in serious damage to your
unit’s shredder blade,
flails or impeller.
1. Grasp the handle with both hands and gently agitate
the chipper shredder to help loosen debris, drawing it
into the impeller.
4. Apply intermittent pressure (force, in short pulses)
while feeding larger (2- 3-inch diameter) branches
into the chipper chute, to avoid bogging or stalling
the engine.
If the clog does not clear, proceed as follows:
1. Stop engine.
2. Use your hands to remove any debris found near the
top of the hopper.
IMPORTANT: Never feed branches with a diameter
greater than three (3) inches into the chipper chute.
Doing so can result in serious damage to your unit’s
chipper blades, flails or impeller.
3. Use a branch (or other available device, i.e. broom-
stick) to dislodge debris located toward the base of the
hopper.
IMPORTANT
Never feed branches with
a diameter greater than
three (3) inches into the
chipper chute. Doing so
can result in serious dam-
age to your unit’s chipper
blades, flails or impeller.
NOTE: For best performance, always operate the
unit with sharp chipper blades. If a noticeable loss in
performance is encountered while chipping branches,
the chipper blades should be replaced.
4. Restart engine.
NOTE: If you’re unable to pull the starter rope as a
result of accumulated debris near the impeller, follow
instructions under the heading Cleaning the Reduction
Chamber in the “Maintaining Your Chipper Shredder”
section of this manual.
Emptying the Debris Collection Bag
1. Stop engine.
2. Squeeze the locking buckle release the bag’s
drawstrap before loosening it from the chute deflec-
tor. See Figure 7.
3. Empty the bag and reattach to the chute deflector
opening. Refer to Figure 2.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
under extremely dusty conditions. Replace the air
cleaner cartridge once a season. To service the air
cleaner, refer to the separate engine manual.
C
3. The spark plug should be cleaned and the gap reset
once a season. Refer to the separate engine manual
for correct plug type and gap specifications.
ꢀ
Maintaining
Your Chipper
Shredder
Chipper Shredder Care
A
Before each use, visually inspect your chipper shredder
for loose (or missing) nuts and bolts. Securely tighten
(or replace) all hardware before operating the chipper
shredder.
B
Cleaning The Reduction Chamber
WARNING: The impeller’s shredder
blade and chipper blades are sharp.
Wear leather work gloves to protect
your hands when cleaning out the
reduction chamber.
Figure 8
If the reduction chamber becomes clogged with debris,
the shredder screen can be pivoted upward so that you
can clean the surrounding area. To do so, proceed as
follows:
C
WARNING
1. Stop engine, disconnect spark plug, and make certain
the chipper shredder has come to a complete stop.
Always stop engine,
disconnect spark plug,
and ground against
engine before cleaning,
lubricating or doing any
kind of maintenance on
your machine.
A
B
WARNING: The muffler and surrounding
area will be hot if the engine has been
running. Use caution and protect your
hands if working near the muffler.
2. a. If attached, remove debris bag. Remove the two
wing knobs on either side of the chute deflector and
pivot the chute deflector upward. See Figure 8.
b. Remove the hairpin clip from the clevis pin which
extends through the housing and shredder screen.
See Figure 8. Remove clevis pin.
The impeller’s chip-
per blades are sharp.
Wear leather work
gloves to protect your
hands.
Model 24A-424G766 Shown
Figure 9
WARNING: Always stop engine,
disconnect spark plug, and ground
against engine before cleaning,
lubricating or doing any kind of
maintenance on your machine.
c. Pivot the shredder screen upward and clean the
surrounding area by scraping away debris.
3. Confirm that the spark plug wire is disconnected
and away from spark plug. Pull on the starter rope
two-to-three times to purge any remaining debris from
the reduction chamber
Lubrication
1. Lubricate the chipper chute hinge a with light oil
once a season.
4. When the area is cleaned, pivot the shredder screen
downward and re-secure with the clevis pin and
hairpin clip removed earlier.
2. Lubricate the pivot points on the chute deflector with
light oil once a season.
3. Refer to the Briggs & Stratton Owner/Operator
manual packed with your unit for engine lubrication
instructions.
5. Reattach the debris collection bag to the chute deflec-
tor, if desired.
Sharpening Or Replacing Chipper
Blades
Engine Care
Refer to the Maintenance section of the Briggs &
Stratton Owner/Operator manual packed with your unit.
Read and follow instructions carefully.
1. Check engine oil level before each use as
instructed in the separate engine manual.
WARNING: The impeller’s chipper
blades are sharp. Wear leather work
gloves to protect your hands.
1. Stop engine, disconnect spark plug, and make certain
the chipper shredder has come to a complete stop.
2. Clean air cleaner’s precleaner every 25 hours
under normal conditions. Clean every few hours
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Pivot the shredder screen upward as instructed under
the heading Cleaning the Reduction Chamber.
3. a. Remove the chipper chute support brace from the
frame by removing the two hex bolts and saddle
washers which secure it. See Figure 9.
ꢀ
b. Remove the chipper chute by removing three hex
nuts and washers which secure it to the impeller
housing. See Figure 9.
Maintaining
Your Chipper
Shredder
• Rotate the impeller by hand until one of the two
chipper blades is visible through the impeller
housing opening.
c. Remove the blade by removing the internal hex
screws, lock washers and hex nuts which secure it
to the impeller. Retain the hardware.
Figure 10
NOTE: Use a 3/16” hex key (Allen) wrench on the outside
of the blade and a 1/2” box (or socket) wrench on the
inside of the impeller. Hold the Allen wrench stationary
and rotate the box (or socket) wrench to loosen the nut.
4. Install a replacement blade (Part No. 742-0544) with
the hardware removed earlier or sharpen.
WARNING
IMPORTANT: When sharpening the blade, protect hands
by using gloves. Follow the original angle of grind and
make sure to remove an equal amount from each blade.
5. To replace the other blade, rotate the impeller to
expose the second blade and repeat the steps above.
The shredder blade is
sharp. Wear leather
work gloves to
B
C
A
protect your hands.
NOTE: Make certain blades are reassembled with the
sharp edge outward (toward the chipper chute). Torque
hardware to between 20 ft.-lbs and 25 ft.-lbs.
Figure 11
NOTE: Use a 3/16” hex key (Allen) wrench on the
outside of the shredder blade and a 1/2” box (or socket)
wrench on the inside of the shredder blade. Hold the
Allen wrench stationary and rotate the box (or socket)
wrench to loosen the nut.
Sharpening Or Replacing The
Shredder Blade
IMPORTANT
Make certain chipper
blades are reassem-
bled with the sharp
edge outward (toward
the chipper chute).
Torque hardware to
between 20 ft.-lbs and
25 ft.-lbs.
WARNING: The shredder blade is sharp.
Wear leather work gloves to protect
your hands.
c. Remove the hex bolt, lock washer, and flat washer
to completely free shredder blade. See Figure 11.
1. Stop engine,disconnect spark plug, and make certain
that all moving parts have come to a complete stop.
IMPORTANT: If sharpening the blade for reuse, follow
the original angle of grind as a guide. Make certain each
cutting edge receives an equal amount of grinding to
prevent an unbalanced blade. Remove metal from the
heavy side until it is balanced evenly.
2. Remove the two flange nuts (and hex bolts) which
secure the hopper support bracket to the impeller
housing. Retain the hardware. See Figure 10.
3. Pivot the shredder screen upward as instructed under
the heading Cleaning the Reduction Chamber.
IMPORTANT: When reassembling the blade, tighten
center bolt to between 45 ft.-lbs and 60 ft.-lbs and the
two out bolts to between 20 ft.-lbs and 25 ft.-lbs.
IMPORTANT
When reassembling the
shredder blade, tighten
center bolt to between
45 ft.-lbs and 60 ft.-lbs
and the two out bolts to
between 20 ft.-lbs and
25 ft.-lbs.
4. a. Remove six flange nuts which secure hopper inlet
guide to impeller housing. See Figure 11.
• Carefully separate the hopper assembly from the
impeller housing and set it aside.
StoringYour Chipper Shredder
1. Clean the equipment thoroughly.
• Insert a piece of wood into the chute deflector
opening to stabilize the impeller and prevent it from
rotating when removing the shredder blade.
b. Remove the two internal hex screws, hex lock nuts,
and lock washers which secure the shredder blade
to the impeller. See Figure 11.
2. Wipe equipment with an oiled rag to prevent rust.
3. Refer to engine manual for correct engine storage
instructions
4. Store unit in a clean, dry area. Do not store next to
corrosive materials such as fertilizer.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Cause
Remedy
1. Throttle lever not in correct starting
position (if equipped).
1. Move throttle lever to FAST or
START position.
Engine fails to start
6
2. Spark plug wire disconnected.
2. Connect wire to spark plug.
3. Choke not in CHOKE position (if
equipped).
3. Move choke lever to CHOKE
position.
Trouble
Shooting
4. Fuel tank empty or stale fuel.
4. Fill tank with clean, fresh gasoline.
5. Engine not primed (if equipped).
5. Prime engine as instructed in
Engine Manual.
6. Clean, adjust gap, or replace.
7. Clean fuel line.
6. Faulty spark plug.
7. Blocked fuel line.
8. Engine flooded.
8. Wait a few minutes to restart, but
do not prime.
1. Spark plug wire loose.
1. Connect and tighten spark
plug wire.
Engine runs erratic
2. Unit running on CHOKE (if equipped).
3. Blocked fuel line or stale fuel.
2. Move choke lever to OFF position.
3. Clean fuel line; fill tank with clean,
fresh gasoline.
For repairs beyond
the minor adjustments
listed here, contact
an authorized service
dealer.
4. Vent in gas cap plugged.
5. Water or dirt in fuel system.
4. Clear vent.
5. Drain fuel tank. Refill with
fresh fuel.
6. Dirty air cleaner.
6. Refer to engine manual.
7. Carburetor out of adjustment.
7. See authorized service dealer.
1. Engine oil level low.
1. Fill crankcase with proper oil.
2. Refer to engine manual.
Engine overheats
2. Dirty air cleaner.
3. Carburetor not adjusted properly.
3. See authorized service dealer.
1. Spark plug gap too close.
1. Adjust gap to .030”.
Occasional skips
(hesitates) at
high speed
2. Carburetor idle mixture adjustment
improperly set.
2. See authorized service dealer.
Excessive
Vibration
1. Loose parts or damaged impeller.
1. Chute deflector clogged.
1. See authorized service dealer.
1. Stop engine immediately and
disconnect spark plug wire. Clean
flail screen and inside of discharge
opening.
Unit does not
discharge
2. Foreign object lodged in impeller.
2. Stop engine and disconnect spark
plug wire. Remove lodged object.
3. Low engine RPM.
1. Low engine RPM.
2. Chipper blade dull.
3. Always run engine at full throttle.
1. Always run engine at full throttle.
Rate of discharge
slows considerably
or composition of
discharged material
changes
2. Replace chipper blade or see your
authorized service dealer.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Series 410 & 420
7
1
1
2
3
4
5
6
7
8
9
681-04009 Impeller Assembly Complete
710-1054 Machine Screw, 5/16-24 x 1.0
711-0833B Clevis Pin,.496
Parts List
2
8
712-0411
715-0166
719-0329
736-0119
Hex Lock Nut, 5/16-24
2
Spiral Pin,.156 x 1.0
Flail
9
10
7
Lock Washer, 5/16
5
4
6
742-04050 Shredder Blade
742-0544
Chipper Blade
Retainer Clip
To order replacement
parts, contact
1-800-520-5520,
1-330-558-7220
or visit
10 781-0735
3
5
3
8
7
1
2
7
9
4
6
1
2
3
4
5
6
7
8
9
681-0133
Tongue Hitch Mount
681-0134A Base Hitch Mount
710-3001
711-0299
711-0835
712-3017
732-0194
736-0133
736-0169
Hex Cap Screw, 3/8-16 x.88
Clevis Pin,.625 x 2.4
Clevis Pin,.50 x 4.62
Hex Nut, 3/8-16
Spring Pin
Flat Washer,.411 x 1.25 x 1.0
Lock Washer, 3/8
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Series 410 & 420
23†
26†
24†
18
21†
6
62‡
25†
19
17†
8†
4
10†
5
27
12
59
1†
4
6
4
30
53†
52‡
6
29
11†
7†
54†
60†
9†
31
14†
6
2†
4†
6†
15†
6†
22
43
16†
46
3†
12
44
6
5
42
32
61
3†
22
13†
22
6†
33
12
47
6
12
58
61
50
49
42
39
51
37
57
22
41
56
48
36
40
28
35
20
38
55
45
20
22
13
† Model 424 Only
‡ Model 414 Only
34
38
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
9
681-04006† Upper Chipper Chute Assembly
681-04007† Lower Chipper Chute Assembly
710-0106† Hex Cap Screw, 1/4-20 x 1.25
34 681-04002 Outer Flail Housing Assembly
35 710-0157 Hex Cap Screw, 5/16-24 x.75
36 710-0502A Hex Sems Screw, 3/8-16 x 1.25
7
710-3013
712-3010
712-3027
Hex Cap Screw, 1/4-20 x.5
Hex Nut, 5/16-18
37 710-0825
38 710-3025
39 726-0211
40 736-0119
41 736-0170
42 750-0793
43 681-0048
720-0170
Hex Cap Screw, 1/4-20 x 3.75
Hex Cap Screw, 5/16-18 x.625
U-Nut, 5/16-18
Hex Lock Nut 1/4-20
Parts List
714-0104† Cotter Pin
Lock Washer, 5/16
728-0175† Pop Rivet
Special Lock Washer, 5/16
Hinge Spacer,.265 x.380 x 1.66
Knob Assembly (Incl. ref.# 12 & 61)
Knob Only, 5/16-18
732-0306A† Compression Spring,.531 x 1.75
10 735-0249A† Chute Flap
11 736-0140† Flat Washer
12 736-0242
13 736-0451
Bell Washer.340 ID x.872 OD
Washer,.320 ID x.93 OD
44 681-0094
45 711-0835
Chute Deflector Assembly
Clevis Pin,.50 x 4.62
14 747-04163† Lock Rod
46 714-0149B Internal Cotter Pin
47 719-04070 Shredder Screen
To order replacement
parts, contact
1-800-520-5520,
1-330-558-7220
or visit
15 749-1004† Chipper Chute Support
16 781-04032† Chipper Chute Hinge
17 781-0633† Chute Flap Strip
18 681-04011 Shredder Hopper Assembly
48 726-0214
49 734-1845
50 736-0366
51 738-0813
Push Cap, 5/8
Wheel, 10 x 4 x 4
Flat Washer,.625 x 1.0
Axle, 22.47”
19 710-0809
20 710-0805
Hex Cap Screw, 1/4-20 x 1.250
Hex Cap Screw, 5/16-18 x 1.50
52 737-0195‡ Elbow Fitting
21 712-04065† Flange Lock Nut, 3/8-16
22 712-3004A Flange Lock Nut, 5/16-18
23 732-04167† Torsion Spring
53 737-0132† Oil Drain End Cap (424 only)
54 737-0298† Oil Drain Pipe (424 only)
55 710-1254
56 736-0217
57 736-0247
Hex Cap Screw, 3/8-24 x 2.2
Lock Washer, 3/8
24 736-0182† Spring Washer,.50 x 1.0 x.022
25 736-0326† Flat Washer,.50 x 1.0 x.0125
26 738-0430† Shoulder Screw, 3/8-16,.50 x.685
27 749-04103 Hopper Handle
Flat Washer,.406 x 1.25
58 681-04009 Impeller Assembly
(See page 13 for Impeller Parts)
Flat Washer,.28 x.74 x.063
60 726-0233† Push Nut,.25ID x.50OD
61 726-0201 Speed Nut,.3125ID
62 681-0095‡ Chipper Chute
28 749-04104 Tube Support
59 736-0173
29 781-04007 Shredder Plate
30 781-04027 Hopper Support Bracket
31 781-04033 Inlet Guide
32 681-0117
Inner Flail Housing Assembly
—
—
664-04023 Debris Collection Bag (Not Shown)
723-0400 Safety Glasses
33 681-0183A† Frame Assembly (Model 424 only)
681-0184A‡ Frame Assembly (Model 425 Incl.)
† Model 424 & 425
‡ Model 414 Only
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR
The limited warranty set forth below is given by Troy-Bilt LLC with respect
deck adjustments, and normal deterioration of the exterior finish
due to use or exposure.
to new merchandise purchased and used in the United States and/or its
territories and possessions, and by MTD Products Limited with respect to
new merchandise purchased and used in Canada and/or its territories and
possessions (either entity respectively, “Troy-Bilt”).
d.
e.
Service completed by someone other than an authorized service
dealer.
Troy-Bilt does not extend any warranty for products sold or
exported outside of the United States and/or Canada, and
their respective possessions and territories, except those sold
through Troy-Bilt’s authorized channels of export distribution.
Replacement parts that are not genuine Troy-Bilt parts.
Transportation charges and service calls.
“Troy-Bilt” warrants this product (excluding its normal wear parts as
described below) against defects in material and workmanship for a period
of two (2) years commencing on the date of original purchase and will, at
its option, repair or replace, free of charge, any part found to be defective
in materials or workmanship. This limited warranty shall only apply if
this product has been operated and maintained in accordance with the
Operator’s Manual furnished with the product, and has not been subject to
misuse, abuse, commercial use, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water, or damage because of other peril
or natural disaster. Damage resulting from the installation or use of any
part, accessory or attachment not approved by Troy-Bilt for use with
the product(s) covered by this manual will void your warranty as to any
resulting damage.
f.
g.
h.
If Products are used commercially. (Troy-Bilt may separately
offer Limited Commercial Warranties on certain select products.
Ask your dealer or retailer for details or contact Troy-Bilt Service
for more information).
No implied warranty, including any implied warranty of merchant-
ability of fitness for a particular purpose, applies after the applicable
period of express written warranty above as to the parts as identi-
fied. No other express warranty, whether written or oral, except as
mentioned above, given by any person or entity, including a dealer or
retailer, with respect to any product, shall bind Troy-Bilt. During the
period of the warranty, the exclusive remedy is repair or replacement
of the product as set forth above.
Normal wear parts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of purchase.
Normal wear parts include, but are not limited to items such as: batteries,
belts, blades, blade adapters, grass bags, rider deck wheels, seats, snow
thrower skid shoes, friction wheels, shave plates, auger spiral rubber and
tires.
The provisions as set forth in this warranty provide the sole and
exclusive remedy arising from the sale. Troy-Bilt shall not be liable
for incidental or consequential loss or damage including, without
limitation, expenses incurred for substitute or replacement lawn care
services or for rental expenses to temporarily replace a warranted
product.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service dealer. To
locate the dealer in your area:
In the U.S.A.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
Check your Yellow Pages, or contact Troy-Bilt LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, or call 1-866-840-6483 or 1-330-558-7220,
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of the
product shall void this warranty. You assume the risk and liability for
loss, damage, or injury to you and your property and/or to others and their
property arising out of the misuse or inability to use the product.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 1-800-668-
This limited warranty does not provide coverage in the following cases:
This limited warranty shall not extend to anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
a.
The engine or component parts thereof. These items may
carry a separate manufacturer’s warranty. Refer to applicable
manufacturer’s warranty for terms and conditions.
Log splitter pumps, valves, and cylinders have a separate
one- year warranty.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited war-
ranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
b.
c.
Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
IMPORTANT: Owner must present Original Proof of Purchase to obtain
warranty coverage.
Troy-Bilt LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-866-840-6483, 1-330-ꢀꢀ8-7220
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
Download from Www.Somanuals.com. All Manuals Search And Download.
|