Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Table of contents
Section I: ..................................................................................................................................................................1
Product Description................................................................................................................................................1
General description.......................................................................................................................................2
Product features.............................................................................................................................................3
Management methods...................................................................................................................................4
Hardware description....................................................................................................................................5
FBRM/BFFG13xx-1xx fiber-to-fiber gigabit models .................................................................................13
Redundant SFBRM1040-140 models ........................................................................................................15
Section II: ...............................................................................................................................................................17
Hardware Installation ...........................................................................................................................................17
Installing CFBRM/CBFFG cards into point system chassis ......................................................................18
Installing SFBRM/SBFFG standalone models............................................................................................19
Installing fiber and copper cables..............................................................................................................20
Connecting power (standalone models)...................................................................................................22
Section III:..............................................................................................................................................................24
USB Driver Installation & COM Port Setup........................................................................................................24
Installing USB driver....................................................................................................................................25
Configuring COM port................................................................................................................................29
Section live: ...........................................................................................................................................................32
Initial Device Setup...............................................................................................................................................32
USB CLI access ............................................................................................................................................33
Initial Device setup via USB CLI................................................................................................................35
Initial Device setup via telnet (directly to Device) ..................................................................................38
Initial Device setup via chassis agent MMU, web-based........................................................................41
Initial Device setup IP web-based (directly to Device)...........................................................................44
Sections V: .............................................................................................................................................................49
Device Management.............................................................................................................................................49
SNMP IP-based management.....................................................................................................................50
Device management via chassis agent (MMU) web-based.....................................................................53
Device management via IP web-base (directly to Device).....................................................................56
Section VI:..............................................................................................................................................................59
Software Features ..................................................................................................................................................59
Software feature descriptions .....................................................................................................................60
Software security feature descriptions.......................................................................................................69
Section VIl:.............................................................................................................................................................71
Operations .............................................................................................................................................................71
Status LEDs...................................................................................................................................................72
OAM Device management configuration options ...................................................................................75
Firmware upgrades......................................................................................................................................76
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Table of contents, continued
Section Vlll: ...........................................................................................................................................................82
Troubleshooting ....................................................................................................................................................82
Troubleshooting problem and corrective action table.............................................................................83
Section lX:..............................................................................................................................................................88
Copper Cable & Fiber Optic Specifications .......................................................................................................88
Copper cables ..............................................................................................................................................89
Fiber optic cable and connector specifications........................................................................................90
Section X:.............................................................................................................................................................101
Contact Us, Warranty, & Conformity Information...........................................................................................101
Contact us...................................................................................................................................................102
Conformity declaration .............................................................................................................................103
Warranty.....................................................................................................................................................105
Compliance information...........................................................................................................................107
Appendix A:.........................................................................................................................................................109
FBRM/BFFG Part Numbers.................................................................................................................................109
FBRM copper-to-fiber part numbers........................................................................................................109
FBRM fiber-to-fiber part numbers ............................................................................................................112
BFFG copper-to-fiber part numbers.........................................................................................................115
BFFG fiber-to-fiber part numbers.............................................................................................................116
Appendix B:.........................................................................................................................................................120
FBRM/BFFG Technical Specification ................................................................................................................120
Specifications, notices, and warnings......................................................................................................120
Appendix C:.........................................................................................................................................................122
Device Commands & Descriptions...................................................................................................................122
Appendix D: ........................................................................................................................................................129
IP-Based and Chassis Management Parameters...............................................................................................129
Appendix E: .........................................................................................................................................................141
Request for Comment (RFC) Compliance.........................................................................................................141
Index.....................................................................................................................................................................143
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Trademark, copyright information, and about this manual
Trademark
All trademarks and registered trademarks are the property of their respective owners.
Copyright
restrictions
© 2008 Transition Networks: All rights reserved. No part of this work may be
reproduced or used in any form or by any means—graphic, electronic, or
mechanical—without written permission from Transition Networks.
Printed in the U.S.A.
About this
manual
This manual is designed to help you find the information you need quickly. It is
structured as follows:
• Table of Contents (TOC)
• Section TOC: Shows all the major topics in the section
• Side Headings: Shows all the sub topics on each page
• Index
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Caution and warnings
Definitions
Cautions indicate that there is the possibility of poor equipment performance or
damage to the equipment. The symbol below identifies cautions
Warnings indicate that there is the possibility of injury to person.
Cautions and Warnings appear here and may appear throughout this manual where
appropriate. Failure to read and understand the information identified by the symbol
could result in poor equipment performance, damage to the equipment, or injury to
persons.
Cautions
When handling chassis Devices observe electrostatic discharge precautions.
This requires proper grounding; i.e., wear a wrist strap.
Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232,
RS422, RS485, DS1, DS3, Video Coax, etc., are intended to be connected to
intra-building (inside plant) link segments that are not subject to lightening
transients or power faults.
Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232,
RS422, RS485, DS1, DS3, Video Coax, etc., are NOT to be connected to
inter-building (outside plant) link segments that are subject to lightening.
DO NOT install the Devices in areas where strong electromagnetic fields
(EMF) exist. Failure to observe this caution could result in poor Device
performance.
Warnings
Use of controls, adjustments or the performance of procedures other than
those specified herein may result in hazardous radiation exposure.
Visible and invisible laser radiation when open. DO NOT stare into the beam
or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section I:
Product Description
In this section
These are the topics:
Topic
See Page
General description
Product features
2
3
Management methods
Hardware description
4
5
FBRM/BFFG13xx-1xx fiber-to-fiber gigabit models
Redundant SFBRM1040-140 models
13
15
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Section I: FBRM/BFFG Product Description
Transition Networks
General description
Design and
configuration
The FBRM and BFFG Devices are designed as standalone models, and also as slide-
in Devices for the Point System chassis. These Devices can be managed through
SNMP via the Focal Point software (free), Web-based management, Local SNMP,
and USB interfaces.
The CFBRM and CBFFG (chassis Devices), and SFBRM and SBFFG (standalone
Devices) are designed to manage Devices remotely through the copper and fiber
ports.
The FBRM or BFFG Devices installed on a network should be configured one as the
local peer and the other as a remote peer for management.
Remote management is accomplished using OAM (Operation Administration and
Maintenance) per the IEEE 802.3ah, 2004 standard. Standalone Devices can also be
managed via IP (Web-based) or Telnet.
What is OAM? These Devices implement the IEEE 802.3ah standard or (OAM) in the Ethernet first
mile. OAM is a group of network management functions that provide network fault
indications, performance information, data, and diagnosis. These Devices implement
remote management via OAM as per the IEEE 802.3ah standard.
In-band
management
These Devices implement complete Real-Time Multi-Threaded Operating System
(RTOS) with a TCP/IP stack for in-band management.
USB interface
The USB (Universal Serial Bus) type “B” serial port is used mainly to configure
Device-basic setup before installation and operation on a network.
Point System
Implements the current Point System management I2C interface. This allows
mgmt interface managing the Device via SNMP, using the existing Point System method.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section I: FBRM/BFFG Product Description
Product features
Supported
features
The following is a list of the major FBRM and BFFG Device supported features:
• Remote Management via OAM (IEEE 802.3ah) and IP-based management
• AutoCross
• Transparent Link pass-through with automatic link restoration
• Far end fault detection on fiber ports
• OAM IEEE 802.3ah
• Auto-Negotiation (enable/disable)
• Force 10 Mbs or 100 Mbs speed (non-gigabit models only)
• Force half or full duplex
• Pause capability
• Automatic firmware upgrade via OAM
• Forwards all IEEE multicast frames including STP/LACP/LAMP
• Enable/disable USB port access
• Enable/disable SNMP queries
• Enable/disable system-level IP management or on a per port basis
• IEEE 802.1q VLAN (virtual local area network)
• Management VLAN for all management frames
• IEEE 802.1x port-based network access control
• Radius authentication for management
• Remote and local firmware upgrades via TFTP (Trivial File Transfer Protocol) or
Xmodem
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Section I: FBRM/BFFG Product Description
Transition Networks
Management methods
Management
The FBRM and BFFG Devices support the following management methods:
• USB CLI (Command Line Interface)
• Telnet
• MMU (Management Module Unit) chassis web-based
• IP-based (web-based directly to the Device)
USB
USB management requires a direct connection to the Device via a computer. This
method is used to set up initially or to troubleshoot Devices in the field.
Telnet
Telnet management requires that the Device be connected to a network. Then from
the CPU command line type Telnet and the Device IP address as shown as follows:
Telnet nnn.nnn.nnn.nnn (represents Device IP address).
MMU
The MMU (Management Module Unit) is the heart of the Point System chassis’
management capability. It has the ability to monitor and manage all its installed
Devices. The MMU communicates through the CLI presented at the serial port, or
through SNMP, Telnet CLI, and Web interface available via the Ethernet port.
IP-based (web-
based)
The switch provides complete management through IP via an SNMP interface, web-
browser, or Telnet. The Device provides an embedded web server for web-based
management. It also offers advanced management features and enables Device
management from anywhere on the network through a standard browser, such as
Microsoft Internet Explorer or Netscape.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section I: FBRM/BFFG Product Description
Hardware description
Front panel
CFBRM
The front panel of the CFBRM10xx-1xx Devices has the following ports and LEDs:
Ports
Front Panel LEDs
• Power (one)
One RJ-45 auto-sensing of 10Base or 10/100Base-TX UTP
connections
• RJ-45 port (two)
One 100Base-FX/LX/BX fiber either SC or ST connectors
• LACT (one)
• DPX (one)
• USB (one)
One USB
Figure 1: Chassis CFBRM10xx-1xx Device Front Panel
Note: The LEDs and ports are the same on the SFBRM10xx-1xx standalone
models.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Section I: FBRM/BFFG Product Description
Transition Networks
Hardware description, continued
Front panel
CFBRM
The front panel of the CFBRM 1040-140 Devices has the following ports and LEDs:
Ports
Front Panel LEDs
• Power (one)
• Link/Active
• Speed
100Base-FX SFP port
10/100 Base-T copper port
• Duplex (one)
• USB (one)
One USB
Figure 2: CFBRM1040-100 Front Panel
Note: The LEDs and ports are the same on the SFBRM1040-140 standalone
models.
Continued on next page
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section I: FBRM/BFFG Product Description
Hardware description, continued
Front panel
The front panel of the CFBRM13xx-1xx Devices has the following ports and LEDs:
CFBRM Gbit
Ports
Front Panel LEDs
• Power (one)
One 100 Base-T
• Fiber-Port Link (one)
• Fiber-Port Link (one)
• USB (one)
One 1000Base-FX/LX/BX fiber either SC or ST connectors
One USB
SC Connector
Fiber
SC Connector
Fiber
USB Port
100Base-T
1000Base-X
PWR
LNK
LNK
USB
Power
LED
USB LED
Fiber Link
LED
Fiber Link
LED
Figure 3: Chassis CFBRM13xx-1xx Device Front Panel
Note: The LEDs and ports are the same on the SFBRM13xx-1xx standalone
models.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Section I: FBRM/BFFG Product Description
Transition Networks
Hardware description, continued
Front panel
The front panel of the CBFFG10xx-1xx Devices has the following ports and LEDs:
CBFFG Gbit
Ports
Front Panel LEDs
• Power (one)
• Link/Active
• Speed
1000Base-SX/LX/BX fiber SC port
10/100/1000Base-T copper port
• Duplex (one)
• USB (one)
One USB
Figure 4: CBFFG10xx-1xx Device Front Panel
Note: The LEDs and ports are the same on the SBFFG10xx-1xx standalone
models.
Continued on next page
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section I: FBRM/BFFG Product Description
Hardware description, continued
Front panel
The front panel of the CBFFG1040-1xx Devices has the following ports and LEDs:
CBFFG Gbit
Ports
Front Panel LEDs
• Power (one)
• Link/Active
• Speed
1000Base SFP port
10/100/1000Base-T copper port
• Duplex (one)
• USB (one)
One USB
SFP Port
Speed
Duplex/Link
USB Port
Power
USB
1000Base-X
10/100/1000
Link Active
USB LED
RJ45 Port
Figure 5: CBFFG1040-1xx Device Front Panel
Note: The LEDs and ports are the same on the SBFFG1040-1xx standalone
models.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Section I: FBRM/BFFG Product Description
Transition Networks
Hardware description, continued
Front panel
The front panel of the CBFFG13xx-1xx Devices has the following ports and LEDs:
CBFFG Gbit
Ports
Front Panel LEDs
• Power (one)
Two 1000Base-FX/LX/BX fiber either SC or ST connectors
One USB
• Fiber-Port Link (two)
• Duplex (one)
• USB (one)
Figure 6: Chassis CBFFG13xx-1xx Device Front Panel
Note: The LEDs and ports are the same on the SBFFG13xx-1xx standalone
models.
Continued on next page
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section I: FBRM/BFFG Product Description
Hardware description, continued
Front panel
SFBRM
The front panel of the SFBRM1040-140 redundant Devices has the following ports
and LEDs:
Ports
Front Panel LEDs
• Power (one)
• Link/Active
• Duplex
• Speed
• Duplex (one)
• USB (one)
1000Base SX/LX SFP ports (2 and 3)
10/100/1000Base-T copper port (1)
One USB
Figure 7: CBFFG1040-140 Device Front Panel
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section I: FBRM/BFFG Product Description
Transition Networks
Hardware description, continued
Rear panel
(standalone)
On the standalone SFBRM and SBFFG Devices only, the rear panel consists of a
power-barrel connector for connecting power via a power adaptor. See Figure 8.
Figure 8: SFBRM/SBFFG 1xxx-1xx Device Real Panel (Standalone Only)
Note: The Point System chassis powers the CFBRM and CBFFG chassis Devices.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section I: FBRM/BFFG Product Description
FBRM/BFFG13xx-1xx fiber-to-fiber gigabit models
Gigabit (Gbit)
models
The FBRM100Base-FX-to-1000Base-X and the BFFG 1000Base-X-to-1000Base-X
are the Gbit versions of the IEEE 802.3ah managed Devices. The BFFG models link
Gbit fiber connections; the FBRM models convert 100Base-Fx 100 Mbit/s to Gbit.
These Devices function generally in the same manner as copper-to-fiber FBRMs, the
difference is the way the ports are configured. See Tables 1 and 2.
Table 1: FBRM13xx-1xx 100Base-FX-to-1000Base-X Device
Port
Configuration
Port 1: 100Base-FX
• Default setting: 100Mbs and full duplex.
• FEFI (Far-end fault indication) is configurable.
Default:
Port 2: 1000Base-X
• Auto-Negotiation enabled.
• OAM enabled and in Active Mode if chassis Device
(passive if standalone).
Table 2: BFFG13xx-1xx 1000Base-X-to-1000Base-X Device
Port
Configuration
Port 1: 1000Base-X
Default: Auto-Negotiation enabled.
Port 2: 1000Base-X
Default:
• Auto-Negotiation enabled.
• OAM is enabled and in Active Mode if chassis Device
(passive if standalone).
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Section I: FBRM/BFFG Product Description
Transition Networks
FBRM/BFFG13xx-1xx fiber-to-fiber gigabit models, continued
Connectivity
The different versions of the FBRM and BFFG can be connected and set up to
manage a remote peer completely. In a mixed setup with other FBRM or BFFG
Devices, consider the connectivity scenarios in Figure 9, and the explanation that
follows:
Figure 9: Connectivity Scenarios
Connection
scenario
explanation
In Figure 9, P2 of the active local peer in both scenarios is “OAM enabled” and
“Active” by default. To manage the remote passive peer via OAM, configure P1 of
the active local peer as follows:
• Enable OAM
• Select Active mode
If the connection to the passive remote peer is made thru P2 of the active local peer,
OAM occurs without human intervention.
Note: Automatic firmware upgrades will not occur with different types of FBRM
or BFFG Device configurations.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section I: FBRM/BFFG Product Description
Redundant SFBRM1040-140 models
Redundant
models
These SFBRM SFP Devices support fiber redundancy. They have two (2) fiber SFP
ports and one (1) copper port. When you tag the fiber ports as primary and secondary
with redundancy enabled, any fault on the primary port results in the secondary port
becoming operational. There is an option for reverting back to the primary once it
has been restored, or you can continue using the secondary port—these are user
selectable features. See Figure 10.
Figure 10: SFBRMs in Redundant Mode
Explanation
With Port 3 as the secondary port in Redundancy Mode and Port 2, the primary goes
down, the following will happen:
Stage
Description
A.
All Physical layer and OAM configurations of Port 2 will be applied to
Port 3.
B.
C.
D.
E.
Port 2 is disabled, and Port 3 initialized to take over.
An SNMP trap is sent indicating that the ports have switched.
OAM reinitializes (resets all OAM counters and event logs).
All the dynamic MAC entries in the ATU are flushed and the active port
has to relearn the entries.
Note: If the configuration option “revert” is set, when the primary port link is
restored the session will revert back to the primary port. If the “revert’ option
is NOT SET and the primary link is restored, the secondary port remains in
operation until the user intervenes.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Section I: FBRM/BFFG Product Description
Transition Networks
Redundant SFBRM1040-140 models, continued
3-port switch
mode
In this mode, the Device acts as a 3-port switch with the fiber port connected to 2
remote Devices. See Figure 11.
Figure 11: 3-Port Switch Mode
Note: In 3-port switch mode:
• Only one OAM session can be active at anytime.
• Transparent Link pass through is not applicable in this scenario. The port
link status from the Devices is received only as SNMP traps.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section II:
Hardware Installation
Introduction
This section describes how to install the CFBRM and CBFFG Devices into a Point
System chassis with a remotely managed SFBRM or CFBRM standalone Device.
Also, shows how to install two SFBRM Devices or two SBFFG standalone Devices
on a network, one as a local Device and the other as a remotely managed Device.
Caution
When handling chassis Devices observe electrostatic discharge precautions.
This requires proper grounding; i.e., wear a wrist strap. Failure to observe this
caution could result in damage to the chassis Device.
In this section
These are the topics:
Topic
See Page
Installing CFBRM/CBFFG Devices into a point system chassis
Installing SFBRM/SBFFG standalone models
Installing copper and fiber cables
18
19
20
22
Connecting power (standalone models)
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Section ll: FBRM/BFFG Hardware Installation
Transition Networks
Installing CFBRM/CBFFG Devices into point system chassis
IMPORTANT
The CFBRM/CBFFG Device product family IS NOT compatible with the CPSMM-
200 and CPSMM-210 MGMT modules when used in a cascaded application. The
CFBRM/CBFFG can be installed in the “master” chassis with the CPSMM-200
MGMT module, but they can not be installed in a cascaded chassis using the
CPSMM-210 MGMT module.
Alternatively, the CFBRM/CBFFG can be used with the CPSMM120 MGMT
module, which does not support chassis cascading.
Caution
Wear a grounding strap and observe electrostatic discharge precautions when
installing the CFBRM/CBFFG Device into the Point System chassis. Failure
to observe this caution could result in damage to the Device.
Chassis Device
installation
To install the chassis Device into the Point System chassis, do the following:
Step
1.
Action
Locate an empty slot in the Point System chassis.
Grasp the edges of the Device by its front panel.
Align the Device with the slot guides and carefully insert the Device into
the installation slot.
2.
3.
4.
5.
Firmly seat the Device against the chassis back panel.
Push IN and ROTATE clockwise the panel-fastener screw to secure the
Device to the chassis. See Figure 12.
Figure 12: CFBRM/CBFFG Device Chassis Installation
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section ll: FBRM/BFFG Hardware Installation
Installing SFBRM/SBFFG standalone models
Standalone
installation
Figure 13 shows a typical installation involving two (2) SFBRM/SBFFG standalone
Devices on a network.
Figure 13: Installation with Two SFBRM/SBFFG Standalone Devices
Note: With the local active standalone Device connected to a remote standalone
passive Device and with “Mode Control” set to “Auto,” the local (active)
Device will manage the remote (passive) Device. This relationship is
established automatically.
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Section ll: FBRM/BFFG Hardware Installation
Transition Networks
Installing fiber and copper cables
Warning
Use of controls, any adjustments, or the performance of procedures other than
those specified herein may result in hazardous radiation exposure.
Visible and invisible laser radiation when open: DO NOT stare into the laser-
light beam or view the beam directly with optical instruments. Failure to
observe this warning could result in an eye injury or blindness.
Fiber cable
To install the fiber cable, do the following:
Step
Action
1.
Locate a 100/1000Base-FX/SX/LX compliant fiber cable with male,
two-stranded connectors installed at both ends. See Figure 14.
Connect the fiber cables to the FBRM or BFFG Devices as shown in
Figure 14.
2.
Figure 14: Fiber Cable Installation
Continued on next page
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section ll: FBRM/BFFG Hardware Installation
Installing fiber and copper cables, continued
Caution
Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232,
RS422, RS485, DS1, DS3, Video Coax, etc. are intended to be connected to
intra-building (inside building) link segments that are not subject to lightening
transients or power faults. Failure to observe this caution could result in
damage to equipment.
Copper cable
To install the copper cable, do the following:
Step
Action
1.
Locate a 10/100 or 10/100/1000Base-T compliant copper cable with
male, RJ-45 connectors installed at both ends.
Connect the RJ-45 connector at one end of the cable to the Device’s RJ-
45 ports.
Connect the RJ-45 connector at the other end of the cable to the 10/100
or 10/100/1000Base-T RJ-45 port on the other Device (switch,
workstation, etc.). See Figure 15.
2.
3.
Figure 15: Copper Cable Installation
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Section ll: FBRM/BFFG Hardware Installation
Transition Networks
Connecting power (standalone models)
Chassis powers Transition Networks’ Point System chassis powers the CFBRM/CBFFG chassis
slide-in Device Devices.
Adapter powers Use an AC power adaptor to power the SFBRM/SBFFG standalone Device. To
standalone
connect power to the Device, do the following:
Step
Action
1.
Connect the barrel connector on the power adapter cord to the power
connector on the Device (located on the rear of the Device).
See Figure 16.
Figure 16: Standalone Device Power Connector
2.
3.
Connect the power adapter plug into AC power.
Verify that the Device has powered UP—the power indicator LED will be
lit.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section ll: FBRM/BFFG Hardware Installation
Intentionally Blank
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section III:
USB Driver Installation & COM Port Setup
Introduction
This section shows how to install the USB driver and configure COM ports.
In this section
These are the topics:
Topic
See Page
Installing USB driver
Configuring COM ports
25
29
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lll: FBRM/BFFG1 Driver Installation & COM Port Setup
Installing USB driver
USB driver
The driver installation instructions are for Windows XP only. Installing the USB
driver using Windows 2000 is similar, but not necessarily identical to the following
Windows XP driver-installation procedure.
Note: The following USB drivers are provided with the product on a CD, also
2003, Win 2002, Win ME/98, Mac OS X, 9, 8, and Linux.
Installing USB
driver
To install the USB driver on a computer with a Windows XP OS, do the following:
Step
Action
1.
Extract the driver (provided CD or from website) and place it in an
accessible folder on the local drive.
2.
3.
Plug the Device into the USB port on the PC to bring up the “found new
hardware” wizard dialog box, shown in Figure 17.
Select RADIO button, “No, not this time” as shown in Figure 17.
Figure 17: Found New Hardware Wizard Dialog Box
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Section lll: FBRM/BFFG USB Driver Installation & COM Port Setup
Transition Networks
Installing USB driver, continued
Installing USB driver (continued)
Step
4.
5.
Action
Click the NEXT button to launch the “installation options” dialog box.
Select RADIO button “Install from a list or specific location
(Advanced)” as shown in Figure 18.
Figure 18: Installation Options Dialog Box
6.
Click the NEXT button to bring up the “driver search installation
options” dialog boxes shown in Figure 19.
Figure 19: Driver Search Installation Options Dialog Box
Continued on next page
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lll: FBRM/BFFG1 Driver Installation & COM Port Setup
Installing USB driver, continued
Step
Action
7.
Use the BROWSE button to locate the USB driver, as shown in
Figure 20.
C:\FBRM/BFFG1xx
Figure 20: Driver Location
8. Click the NEXT button to start installing the driver and the driver-install
screen will appear as XP copies the Device driver. See Figure 21.
FBRM/BFFG1xx Driver
Figure 21: Windows XP Installing Driver Box
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Section lll: FBRM/BFFG USB Driver Installation & COM Port Setup
Transition Networks
Installing USB driver, continued
Step
Action
9.
After the driver installation is successful, the “finished installing” dialog
box will appear, as shown in Figure 22.
Figure 22: Finish Installing Driver Dialog Box
10.
Click the FINISH button and a “found new hardware” message will
appear on the lower right side of the screen, as shown in Figure 23.
Figure 23: New Hardware Installed and Ready to Use
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lll: FBRM/BFFG1 Driver Installation & COM Port Setup
Configuring COM port
Getting COM
port number
You need the COM port number to configure the terminal emulator. To get the COM
port number, do the following:
Step
Action
1.
On the desktop, right click on the “my computer” icon and select
“Device manager” to open the “computer management” window.
Click on “Device manager” to open the Device manager’s panel (screen
right panel) shown in Figure 24.
2.
Figure 24: Computer Management Window
Expand the Ports (COM & LPT) in the right column and write down the
USB COM port number for configuring the terminal emulator software
used for the USB Device.
3.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Section lll: FBRM/BFFG USB Driver Installation & COM Port Setup
Transition Networks
Configuring COM port, continued
Terminal
To set up the terminal emulator software, e.g., HyperTerminal to use the USB COM
emulator setup port, do the following:
Step
Action
1.
Activate the “HyperTerminal” software to bring up the “connection
description” dialog box, shown in Figure 25.
Figure 25: Connexion Description Diallo Box
2.
3.
Type in a name and select an icon.
Click the OK button to launch the “connect to” dialog box, shown in
Figure 26.
Figure 26: Connect To Dialog Box
Continued on next page
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lll: FBRM/BFFG1 Driver Installation & COM Port Setup
Configuring COM port, continued
Terminal emulator setup (continued)
Step
Action
4.
Select the COM port identified for the USB Device shown in the Device
manager.
5.
Click the OK button to bring up the “port settings” dialog box, shown in
Figure 27.
Figure 27: COM Port Settings Dialog Box
6.
Set the COM port properties as follows:
• Baud:
57600
• Data length:
• Parity:
• Stop bit:
8
None
1
• Flow Control: None
7.
Click the OK button and the Device login prompt will appear.
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section live:
Initial Device Setup
Introduction
There are four ways to set up the FBRM/BFFG 1xxx-1xx Devices before the Device
can be operated and managed:
• USB CLI
• Telnet
• Chassis MMU (chassis model)
• IP-based (directly to FBRM/BFFG)
The factory default IP configuration is the following:
• IP address:
• Subnet Mask: 255.255.255.0
• Gateway: 192.168.1.2
192.168.1.1
In this section
These are the topics:
USB CLI access
Topic
See Page
33
35
38
41
44
Initial Device setup via USB CLI
Initial Device setup via Telnet (directly to Device)
Initial Device setup via chassis agent (MMU) web-based
Initial Device setup via IP web-based (directly to Device)
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lV: FBRM/BFFG Initial Device Setup
USB CLI access
Accessing the
USB CLI
To access the USB CLI, do the following:
Step
1.
Action
Connect the Device to a computer via the USB port.
2.
3.
4.
Activate the terminal emulator software to launch the emulator screen.
Press the ENTER key to bring up the “password” prompt.
Enter the password and then the login (default is “root” in both cases) to
bring up the Device console> prompt, shown in Figure 28.
Password :
Login : root
Password :
Console:/>_
Figure 28: Device Console Prompt
To access the commands list, at the console> prompt type help or “?”
Press the ENTER key to launch the “commands” screen, shown in
Figure 29.
5.
6.
Figure 29: Commands for FBRM/BFFGs Models
Note: See Appendix C for a complete list of the configuration commands and
definitions. All CLI commands are case sensitive.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Section IV: FBRM/BFFG Initial Device Setup
Transition Networks
USB CLI access, continued
Redundant
The following is the screen of commands for the redundant SFP Devices.
Figure 30: Commands for Redundant SFP Models
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lV: FBRM/BFFG Initial Device Setup
Initial Device setup via USB CLI
IP
Use the ‘set’ commands to set the IP configuration through the USB port. Configure
the Device with a network IP address, subnet mask, and default gateway. Set the IP
address via USB CLI (Command Line Interface), or via DHCP (Dynamic Host
Configuration Protocol), which is disabled by default.
configuration
Factory default The factory default IP configuration shipped with the Device is as follows:
IP config
• IP address:
• Subnet Mask: 255.255.255.0
• Gateway: 192.168.1.2
192.168.1.1
Note: Type “help set <command>” to display the format used to set the commands.
Set IP config
via USB CLI
To set the IP via the USB CLI, do the following:
Step
1.
Action
At the console> prompt type set ip=nnn.nnn.nnn.nnn
Press the ENTER key to set the IP address.
At the console> prompt type set netmask=nnn.nnn.nnn.nnn
Press the ENTER key to set the netmask.
At the console> prompt type set gateway=nnn.nnn.nnn.nnn
At the console> prompt type save
2.
3.
4.
5.
6.
7.
Press the ENTER key to save the new IP configuration.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Section IV: FBRM/BFFG Initial Device Setup
Transition Networks
Initial Device setup via USB CLI, continued
DHCP method
To set the IP configuration via the DHCP in console mode, do the following:
Note: A DHCP server must be on the network and accessible before using this
method.
Step
1.
Action
At the console> prompt type set dhcp=enable
2.
Press the ENTER key and the screen will appear as shown in Figure 31.
Figure 31: Enable DHCP
Type reboot
3.
4.
Press the ENTER key to reboot the Device and start the DHCP process.
Note: DHCP “successful” will appear on the screen when completed, or “failed” if
not successful.
Continued on next page
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lV: FBRM/BFFG Initial Device Setup
Initial Device setup via USB CLI, continued
Show system
configuration
To show the Device system configuration, do the following:
Step
1.
Action
At the console> prompt type show
2.
Press the ENTER key to bring up the Device system configuration screen,
shown in Figure 32.
Figure 32: Example System Configuration Screen
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Section IV: FBRM/BFFG Initial Device Setup
Transition Networks
Initial Device setup via telnet (directly to Device)
To set up the Device initially via telnet directly to the Device, do the following:
Initial setup via
Telnet to
Device
Step
Action
1.
At the command line type: Telnet nnn.nnn.nnn.nnn (IP address of the Device) to
bring up the password prompt, shown in Figure 33.
Figure 33: Password Prompt
2.
3.
Type the case-sensitive username and password (default is ‘root’ for
both).
Press the ENTER key to launch the console prompt, shown in Figure 34.
Figure 34: Console Prompt
Continued on next page
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lV: FBRM/BFFG Initial Device Setup
Initial Device setup via telnet (directly to Device), continued
Step
4.
Action
At the console:/> prompt type show
5.
Press the ENTER key to display the system configuration, as shown in
Figure 35.
Figure 35: System Configuration Screen
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Section IV: FBRM/BFFG Initial Device Setup
Transition Networks
Initial Device setup via telnet (directly to Device), continued
Step
Action
6.
At the console prompt type: help
7.
Press the ENTER key to show the commands, shown in Figure 36.
Figure 36: Device Command Screen
Note: The CLI and Telnet interface commands are structured in the same manner.
Terminating
telnet
To disconnect the Telnet client from the management module server, press the
CTRL-D keys, or at the console prompt type: exit or logoff
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lV: FBRM/BFFG Initial Device Setup
Initial Device setup via chassis agent MMU, web-based
Setup via Web
to MMU
To set up the Device initially via the MMU web-based, do the following:
Step
1.
Action
Open a web browser.
2.
3.
At the URL type the IP address of the chassis (MMU).
Click the GO button to bring up the password screen, shown in Figure 37.
Figure 37: Chassis Agent (MMU) Log In Screen
4.
5.
Type the password (default is private).
Press the ENTER key to launch the chassis agent’s main menu, shown in
Figure 38.
Figure 38: Chassis Agent (MMU) Main Menu
6.
Click the VIEW button to show the Devices in the chassis and the screen
will appear, as shown in Figure 39.
Figure 39: Point System Chassis Main Menu
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Section IV: FBRM/BFFG Initial Device Setup
Transition Networks
Initial Device setup via chassis agent MMU, web-based, continued
Step
Action
7.
Click the VIEW button of the CFBRM/CBFFG Device in slot 9 to show
the local configuration screen for the Device. See Figure 40.
Note: You can configure the IP along with other Device parameters on this screen.
Figure 40: Local Switch FBRM/BFFG Configuration Screen
Note: DO NOT use the browser BACK button to navigate the screens. This will
cause the connection to drop.
Continued on next page
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lV: FBRM/BFFG Initial Device Setup
Initial Device setup via chassis agent MMU, web-based, continued
IP config via
DHCP
To configure the IP via DHCP, do the following:
Step
1.
2.
3.
4.
Action
A DHCP server must be on the network and accessible.
On the local switch configuration screen, enable DHCP.
On the local switch configuration screen set item Reset Switch to “Yes.”
Click the SAVE/EXECUTE button to start the DHCP process.
Note: To verify that the DHCP IP configuration was successful, check the IP
configuration for the Device on the local switch screen and note the changes
to the IP configuration.
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Section IV: FBRM/BFFG Initial Device Setup
Transition Networks
Initial Device setup IP web-based (directly to Device)
Initial setup via To set up the Device initially via a IP web-based, do the following:
IP to Device
Step
1.
Action
Open a web browser.
2.
At the URL type in the FBRM/BFFG default IP address.
3.
Click the GO button to launch the password screen shown in Figure 41.
Figure 41: Login Screen
4.
5.
Type the password (default is private).
Press the ENTER key to launch the FBRM/BFFG main menu, as shown
in Figure 42.
Figure 42: FBRM/BFFG Main Menu
Continued on next page
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lV: FBRM/BFFG Initial Device Setup
Initial Device setup IP web-based (directly to Device), continued
Step
Action
6.
Click the local system configuration VIEW button to show the local
system configuration menu, shown in Figure 43.
Note: You can configure the IP along with other Device parameters on this screen.
Figure 43: FBRM/BFFG Local System Configuration Screen
Note: DO NOT use the browser BACK button to navigate the screens. This will
cause the connection to drop.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Section IV: FBRM/BFFG Initial Device Setup
Transition Networks
Initial Device setup IP web-based (directly to Device), continued
IP config via
DHCP
To set up the IP configuration via DHCP, do the following:
Step
1.
Action
A DHCP server must be on the network and accessible.
2.
On the local switch configuration screen, enable DHCP as shown in Figure
44.
Figure 44: IP-based Local System Configuration Screen
3.
Click the Local REBOOT button at the top of the screen to start the DHCP
process.
Note: To verify that the DHCP IP configuration was successful, check the IP
configuration for the Device on the local system configuration screen and
note the changes to the IP configuration.
Continued on next page
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lV: FBRM/BFFG Initial Device Setup
Initial Device setup IP web-based (directly to Device), continued
Redundant
Devices
To set up the redundant feature for the stand-alone 3-port FBRM SFP Device via IP
web-based, do the following:
Step
1.
Action
Open a web browser.
2.
3.
At the URL type in the SFBRM default IP address.
Click the GO button to launch the password screen shown in Figure 45.
Figure 45: Login Screen
4.
5.
Type the password (default is private).
Press the ENTER key to launch the SFBRM main menu, as shown in
Figure 46.
Figure 46: Redundant Device Main Menu
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Section IV: FBRM/BFFG Initial Device Setup
Transition Networks
Initial Device setup IP web-based (directly to Device), continued
Step
Action
6.
Click the advance system configuration VIEW button to show the
redundancy configuration parameters, shown in Figure 47.
Figure 47: Redundancy Configuration Screen
Note: The redundancy features are specific to the 3-port SFBRM SFP Device
only.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Sections V:
Device Management
In this section
These are the topics:
Topic
See Page
SNMP IP-based management
Device management via chassis MMU web-based
Device management via IP (directly to Device)
50
53
56
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Section V: FBRM/BFFG Device Management
Transition Networks
SNMP IP-based management
SNMP
The FBRM/BFFG Device provides complete management through the SNMP
interface. It supports the following standard MIBs for management, using SNMPv1:
• RFC 1213 (MIB- II)
• RFC 2819 (RMON – statistics group)
• RFC 2863 (IF MIB counters)
• RFC 3635 (Ether-like MIB counters)
• RFC 1493 (Bridge MIB objects counters)
• RFC 2674 (Bridge extension counters)
I-D: draft-ietf-hubmib-efm-mib (EFM OAM mib – the EFM hub mib is added to the
TN private tree since it has not been added to the ISO tree.) Use the provide version
shipped on the CD with your Device.
See Figure 48.
EFM-Hub MIBs
Figure 48: EFM Hub MIBs Added to Private Tree
Continued on next page
50
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section V: FBRM/BFFG Device Management
SNMP IP-based management, continued
The TN private MIBs for SNMP IP-based management feature extensive
management options. Some of the features are the following:
TN private
MIBs
• Copper and fiber link status
• Copper and fiber port duplex
• Administratively enable/disable port
• Copper port speed
• Enable/disable Auto-Negotiation (copper)
• Enable/disable Pause
• Enable/disable capability advertisement for speed and duplex
• RMON statistics
• AutoCross on copper port
• Remote fault detect
• Enable/disable far-end fault on fiber
• Transparent link-pass through
• 802.3ah OAM enable/disable on all ports
• OAM channel statistics
• OAM remote loopback
• Rate limiting/band width allocation using fixed rate sets
• IP traffic class priority
• 802.1q VLAN support
• Virtual cable test
The remote Device can be managed completely through OAM. Figure 49 shows an
example of a private MIB objects tree.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Section V: FBRM/BFFG Device Management
Transition Networks
SNMP IP-based management, continued
MIB objects
Figure 49 shows the placement of the MIB objects on the private tree.
Private MIB Objects
Figure 49: Private MIB Objects
52
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section V: FBRM/BFFG Device Management
Device management via chassis agent (MMU) web-based
Management
via MMU
To set up the FBRM/BFFG initially via the MMU, do the following:
Step
1.
Action
Open a web browser.
2.
3.
At the URL type the IP address of the chassis (MMU).
Click the GO button to launch the password screen. See Figure 50.
Figure 50: Chassis Agent (MMU) Login Screen
4.
5.
Type the password (default is private).
Press the ENTER key to launch the chassis agent’s main menu, as shown
in Figure 51.
Figure 51: Chassis Agent (MMU) Main Menu
6.
Click the VIEW button to show the Devices in the cabinet slots, as shown
in Figure 52.
Figure 52: Devices in Chassis Slots
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Section V: FBRM/BFFG Device Management
Transition Networks
Device management via chassis agent (MMU) web-based, continued
Step
Action
7.
Click the VIEW button of the CFBRM/CBFFG Device to bring up the
local switch management screen. See Figure 53.
Figure 53: Local Switch Configuration Screen
8. Scroll down to the LOCAL PORT buttons, shown in Figure 54.
Figure 54: Local System Configuration Local Port Buttons
Note: DO NOT use the browser BACK button to navigate the screens. This will
cause the connection to drop.
Continued on next page
54
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section V: FBRM/BFFG Device Management
Device management via chassis agent (MMU) web-based, continued
Step
Action
9.
Click a PORT BUTTON to bring up the local port switch configuration
screen, shown in Figure 55.
10. Scroll down the screen to see the remaining parameters.
Note: You can set OAM and other parameters on this screen.
Figure 55: Port 1 Local Switch
Note: DO NOT use the browser BACK button to navigate the screens. This will
cause the connection to drop.
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Section V: FBRM/BFFG Device Management
Transition Networks
Device management via IP web-base (directly to Device)
Introduction
The FBRM/BFFG Device supports complete Web-based management for viewing
statistics and configuring the Device. See the help file on Transition Networks
website for more details about different configuration variables.
IP web-based
management
To manage the Device via the IP web-based, do the following:
Step
1.
Action
Open a web browser.
2.
3.
4.
At the URL type the IP address of the Device.
Click the GO button to bring up the password screen, shown in Figure 56.
Enter the password (default password is “private”).
Figure 56: Device Password Screen
Note: DO NOT use the browser BACK button to navigate the screens. This will
cause the connection to drop.
Continued on next page
56
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section V: FBRM/BFFG Device Management
Device management via IP web-base (directly to Device), continued
IP web-based management (continued)
Step
5.
Action
Click the LOG IN button to bring up the main menu of the Device. See
Figure 57.
Note: Any Transition Networks FBRM/BFFG remote peer can be completely
managed by an FBRM/BFFG local peer through OAM.
Figure 57: FBRM/BFFG Main Menu
Note: DO NOT use the browser BACK button to navigate the screens. This will
cause the connection to drop.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Section V: FBRM/BFFG Device Management
Transition Networks
Device management via IP web-base (directly to Device), continued
OAM
The OAM configuration screen allows enabling or disabling OAM by setting the
configuration
mode to “active” or “passive.” If the remote Device is a Transition Networks
FBRM/BFFG Device, the main menu (PORT button with the remote Device
connected) will show the options for managing the remote OAM peer.
The Devices are interoperable with other IEEE 802.3ah compliant Devices. Standard
OAM discovery, loopback, dying gasp, link and other critical events are supported.
The OAM configuration screen for that port will show the following:
• OAM state
• MAC address
• OUI (unique identifier)
Note: On the SFBRM1040-1xx redundant models, there can be only one (1) OAM
session at a time—the OAM enabled port is user selected. Port 2 fiber is the
default port.
OAM config
screen
To view the OAM configuration screen for non-transition networks IEEE 802.3ah
compliant Devices, do the following:
Step
1.
Action
Click any port VIEW button on the CFBRM/CBFFG main menu to bring
up configure screen of that port.
2.
3.
Click the OAM Config button and the screen will appear, as shown in
Figure 58.
You can set up OAM parameters on this screen.
Figure 58: OAM Configuration and Status Screen (OAM Config Button)
58
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section VI:
Software Features
Introduction
In this section
This section explains the operational status LEDs and what they indicate, along with
product features, and the three (3) methods used to upgrade the software.
These are the topics:
Topic
See Page
Software feature descriptions
Software security feature descriptions
60
69
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vl: FBRM/BFFG Software Features
Transition Networks
Software feature descriptions
Note: The FBRM/BFFG Devices does not have configuration switches.
Firmware
activated
features
The FBRM/BFFG series Devices features can be configured via USB, MMU, or IP.
Table 3 explains the configurable parameters of the Devices.
Table 3: Device Software Configurable Features
Feature
Description
AutoCross
(10/100Base-T or
10/100/1000Base-T)
When the AutoCross feature is active, it allows the use
of a straight-through (MDI) or crossover (MDI-X)
copper cable when connecting to 10/100Base-T or
10/100/1000Base-T Devices. AutoCross determines the
characteristics of the connection and configures the
Devices to link up automatically. This occurs regardless
of the cable configuration: MDI or MDI-X. (Transition
networks recommends leaving AutoCross in default
mode, “enabled.”)
Automatic Firmware
Upgrades
The Device has an automatic firmware upgrade feature.
This feature applies to a communication link between a
local peer and its remote peer Devices connected via a
fiber optic cable. If the remote passive peer Device is not
in Active Mode and a local active peer Device detects a
different firmware revision on its remote passive peer
Device, the local active Device will force a bootload
condition and download its firmware revision to its
remote passive peer Device.
Note The local Device could have a different firmware
revision (newer or older) than its remote peer. In
either case, the firmware revision on the local
Device will replace that of its remote passive
peer.
Note: The firmware of the local active peer Device
should be upgraded before the remote passive
peer Device to ensure that the correct firmware
version is on both Devices.
Continued on next page
60
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks Section
Vl: FBRM/BFFG Software Features
Software feature descriptions, continued
Table 3: Device Software Configurable Features (continued)
Feature
Description
Auto-Negotiation
This feature allows the two Devices to configure
themselves to achieve the best possible mode of
operation over a link, automatically. The Device
broadcasts its speed and duplex (full or half) capabilities
to the other Device and negotiates the best mode of
operation. Auto-Negotiation allows quick connections
because the optimal link between the Devices is
established automatically.
In a scenario where the Device links to a non-
negotiating Device, disable Auto-Negotiations. In this
instance, the mode of operation will drop to the lowest
common denominator between the two Devices; e.g., 10
Mb/s at half-duplex.
Disabling this feature allows forcing the connection to
the desired speed and duplex mode of operation.
The firmware uses TFTP to upload its present
Backup Configuration
configuration onto a TFTP server, and can also
download the configuration from the TFTP server and
update its settings. This is useful when you want to
program more than one unit to the same configuration.
One unit can be programmed and that configuration can
be used to populate the other units. Care should be taken
on some settings such as IP address and VLAN settings.
Bandwidth Allocation by This feature can be used with ‘ingress/egress’ frames.
priority (ingress/egress)
It allows setting the bandwidth in varied increments,
starting at 64kps to full bandwidth.
Rate Limiting based on frame priorities can also be
configured. Each higher priority frame can be
configured to get twice the bandwidth of lower priority
frames; e.g., priority “3” frame configurations can get
twice the bandwidth of priority “2” frames.
Egress bandwidth allocation in 64Kbits/sec increments:
• Rate limit all frames
Ingress bandwidth allocation in 64Kbits/sec increments
with four filter selections:
• Rate limit all frames
• Rate limit multicast, flooded unicast, and broadcast
• Rate limit multicast and broadcast
• Rate limit broadcast
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vl: FBRM/BFFG Software Features
Transition Networks
Software feature descriptions, continued
Table 3: Device Software Configurable Features (continued)
Feature
Description
Congestion Reduction
The FBRM and BFFG Devices do not forward collision
signals or error packets between collision domains,
which improves baseline network performance.
In addition, the Devices filter packets destined for local
Devices, which reduces network congestion.
Far-End Fault (FEF)
FEF is a troubleshooting feature. With FEF enabled, if
the receiver on the fiber port goes “down” on one
Device, a FEF idle pattern is sent to the other Device to
terminate data transmission. Then an SNMP trap is sent
to the administrator, identifying the fiber link loss.
If FEF is disabled, a “down” Rx link on one Device
does not transmit to its peer, the down link notification
will not be passed on.
For FEF enabled and disabled scenarios, see illustration
below.
Far-End Fault Detection If FEFD is enabled when the receiver on the fiber port
(FEFD) Fiber Ports
goes down on one Device, it sends a far-end-fault
pattern to the other side to bring down the fiber port on
both ends. An SNMP trap will be sent to the
administrator, indicating the fiber link loss.
If FEFD is disabled, a “down” Rx link on one Device is
not transmitted to the other Device; the link down signal
will not be passed over the link.
Continued on next page
62
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks Section
Vl: FBRM/BFFG Software Features
Software feature descriptions, continued
Table 3: Device Software Configurable Feature (continued)
Feature
Description
Full Duplex
In a full-duplex network, maximum cable lengths are
determined by the cable type. See the Cable
Specifications section for the different FBRM and BFFG
models.
The 512-Bit Rule does not apply in a full-duplex
network.
Firmware upgrades
Auto firmware upgrade enable/disable:
(bootloader)
In some cases, there may not be a requirement for
automatic firmware upgrades. For example, one might
connect a remote peer Device with the latest firmware
version before upgrading the local peer Device.
Typically, the local peer Device would detect a different
firmware version and will downgrade the firmware on
the remote peer Device. To prevent this, disable
automatic upgrade on the remote peer Device. The
remote peer Device will reject all upgrade requests from
the local peer Device—you can then upgrade the local
Device.
Force upgrade:
This is used to force a firmware upgrade on the remote
peer Device when the auto-upgrade feature is disabled on
the remote peer Device. This gives the local peer Device
authority to override the auto-upgrade feature of its
remote peer Device.
Half Duplex
In a half-duplex network, the maximum cable lengths are
determined by the round trip delay limitations of each
Fast Ethernet collision domain. (A collision domain is
the longest path between any two terminal Devices, e.g.,
terminal, switch, or router.)
The 512-Bit Rule determines the maximum length of
cable permitted by calculating the round-trip delay in bit-
times (BT) of a particular collision domain. If the result
is less than or equal to 512 BT, the path is good.
For more information on the 512-Bit Rule, see the white
paper titled “Collision Domains” on Transition
Networks’ website at: www.transition.com
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vl: FBRM/BFFG Software Features
Transition Networks
Software feature descriptions, continued
Table 3: Device Software Configurable Features (continued)
Feature
Description
Operation
Note: On the SFBRM1040-1xx redundant models, there
can be only one (1) OAM session at a time—the
OAM enabled port is user selected. Port 2 fiber is
the default port.
The Device implements the IEEE OAM 802.3ah
standard for troubleshooting and remote management.
This product implements OAM on both the fiber and
twisted pair interfaces. It implements the following
OAM features:
Administration and
Maintenance (OAM,
IEEE 802.3ah-2004
standard)
• Discovery
• Remote Loop Back
• Exchange of configuration information and remote
firmware upgrades with organization specific PDUs
• Link status failure indication
The Device implements the draft-ietf-hubmib-efm-mib
(EFM OAM MIB). Use the version provided on the CD.
When the link on the other port fails, the Device sends an
OAM critical event signal to its peer, indicating the fault
condition.
Critical Event (OAM,
IEEE 802.3ah-2004
standard)
Discovery (OAM,
IEEE 802.3ah-2004
standard)
An active-state Device initiates OAM communications
by sending PDUs across the link connected to an OAM
enabled port. The Device at the other end (if OAM
capable) responds to the request from the active Device
by establishing an OAM communications channel.
Event Notification with
Log In (OAM,
IEEE 802.3ah-2004
standard)
An OAM link event notifies its OAM peer of any symbol
or frame errors that occurred on its link. The window
used for error monitoring, along with the threshold value
are configurable. At the end of the window, if the errors
are greater than or equal to the threshold value, an OAM
event notification is sent to its peer. If the threshold is set
to zero, then at the end of each window an event
notification is sent—this acts more like an asynchronous
update of the link statistics.
Continued on next page
64
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks Section
Vl: FBRM/BFFG Software Features
Software feature descriptions, continued
Table 3: Device Software Configurable Features (continued)
Feature
Description
Last Gasp/Dying
Gasp(OAM, IEEE
All FBRM/BFFG Devices come equipped with a Last
Gasp/OAM Dying Gasp feature. This feature enables
802.3ah-2004 standard) the Device to store a small amount of power to enable
sending an SNMP trap to alert the management console
of a power failure. Feature benefits are the following:
• Notification of an impending power loss before it
happens
• Allows for quicker resolution of the power loss
The default action for last gasp/OAM dying gasp is to
send an SNMP Trap. If the desire is to send a dying
gasp through OAM, it must be configured through the
SNMP/Web interface. It requires choosing the port on
which to send the Dying Gasp command since both
ports are OAM capable. This feature helps
communicate with OAM peers that are not TN Devices.
Remote Loop Back
(OAM, IEEE 802.3ah-
2004 standard)
OAM remote loop back can be used to test link health
by sending a loop back request from the active peer
Device to the remote passive peer Device. Once the
remote passive peer enters loop back mode, all frames
coming into that port are looped back, yet not forwarded
to other ports.
The OAM frames are still exchanged between the local
and remote peer Devices—only OAM frames get
through. The active peer Device discards the frames
coming out of its remote peer Device to prevent
flooding the network. See the illustration below.
Alternate Loop back
This feature can be used to verify end-to-end
connectivity.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vl: FBRM/BFFG Software Features
Transition Networks
Software feature descriptions, continued
Table 3: Device Software Configurable Feature (continued)
Feature
Description
OAM Exchange of
configuration
information and remote
upgrades with
organizational specific
PDUs ( IEEE 802.3ah-
2004 standard)
The remote peer Device (only if a TN
FBRM/BFFGDevice) set to passive mode can be
completely managed through the SNMP/Web
management by its active peer Device when set to
Active Mode. This is done using organizational specific
PDUs. When the active peer upgrades to a new revision
of firmware, it detects the firmware configuration of its
remote peer Device and upgrades it automatically.
If the active peer is in a chassis, the remote peer can be
managed through Point System management by the
management module unit (MMU).
Link Status Failure
Indications
Link status failure indication with OAM PDU flags
fielded and sent as an OAM critical event (refer to
57.4.2.1 of the standard).
Standard MIB Counters
The Device provides complete management through the
SNMP interface. It supports the following standard
MIBs for management using SNMPv1:
• RFC 1213 (MIB-II)
• RFC 2819 (RMON – statistics group)
• RFC 2863 (IF MIB counters)
• RFC 3635 (Ether-like MIB counters)
• RFC 1493 (Bridge MIB object counters)
• RFC 2674 (Bridge extensions counters)
Continued on next page
66
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks Section
Vl: FBRM/BFFG Software Features
Software feature descriptions, continued
Table 3: Device Software configurable Features (continued)
Feature
Description
Pause (flow control) and
Back Pressure
Pause is used to suspend data transmission temporarily
to relieve buffer congestion. If a Device needs sometime
to clear network congestion, it will send a pause signal
to the Device at the other end, then that Device will wait
a predetermined amount of time before re-transmitting
its data.
This feature reduces data bottlenecks and allows
efficient use of network Devices, preventing data losses.
The pause feature is set in Firmware mode, using the
SNMP interface. It can be set to one of four settings:
• Disable (no pause)
• Symmetrical pause
• Asymmetric TX (transmit) pause
• Asymmetric RX (receive) pause
Note: Enable the “pause feature” if available on ALL
network Devices attached to the media
Device(s), otherwise disable this feature.
Back pressure is used in half duplex mode. Back
pressure ensures the retransmission of incoming packets
when a port using half-duplex is temporarily not able to
receive in coming frames.
Point System
Management
The slide-in Device plugs into the chassis to provide
management through the I2C interface. This provides
SNMP and Web-based management through the MMU.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vl: FBRM/BFFG Software Features
Transition Networks
Software feature descriptions, continued
Table 3: Device Software Configurable Features (continued)
Description
Feature
With OAM enabled, TLPT with automatic link
restoration is available for the copper ports on the local
and remote peer Devices. When a copper port goes
“down,” the information is passed to the other Device
and the copper port on that Device will go “down.”
When the link is restored, the link on the other port is
also restored—the fiber ports remain UP. When TLPT is
disabled, if the copper port link drops it does not affect
its peer’s copper port links.
Transparent Link-Pass
Through (TLPT) and
Auto Link Restoration
Note: In the redundant
models (SFBRM1040-
1xx) this feature only
works when the Device
is in redundant mode.
Auto Link Restoration will restore the broken link
automatically upon correcting the fault condition.
For TLPT disabled and enabled scenarios, see the
illustrations below.
The feature monitors the fiber Rx port for signal loss. If
the fiber Rx goes “down,” the copper port stops
transmitting. See illustration below.
Selective Link Pass
Through
68
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks Section
Vl: FBRM/BFFG Software Features
Software security feature descriptions
Table 4: Device Software Configurable Security Features
Description
Security Feature
802.1x MAC filtering
When enabled on a port, stops learning all MAC
addresses. To allow any frame with a MAC address not
in the Static MAC database access, the user needs to add
the new address or it will be discarded. This allows
filtering any unauthorized access to the network by
unknown MAC addresses.
CLI Timeout on Idle
If the CLI session on USB/Telnet is idle for more than
two (2) minutes, the session will time out requiring
logging in to re-gain access to the CLI.
IP access (system
level/port level)
Any management of the system via IP can be locked at
the system level, or only on certain ports. For example
management can occur via web/SNMP only on Port 1, so
that access via other ports can be blocked.
MAC addresses blocking The MAC address can be added to the static MAC
address database with the ‘connected port’ as zero. This
will cause any frames from that MAC address database
to cause an ATU-member violation on that port,
resulting in sending a trap. This could cause excessive
traps (overload the CPU with interrupts) depending on
the traffic generated by that MAC. The user can disable
all traps by setting the Ignore SA Violation on the port
that is receiving the MAC address under Advanced Port
Configuration on the web page.
Management VLAN
SNMP access
In a VLAN enabled network, the administrator can
assign a VLAN as a management VLAN. This VLAN
ID will be used in all management frames. This separates
the management traffic from the data.
The administrator can stop all SNMP access to the
Device, if not used. This will prevent unauthorized
access to the system configuration, but the SNMP traps
will still be sent.
Radius authentication
The Device supports authentication using the RADIUS
protocol. When enabled, RADIUS authentication is used
for Web login, serial port, and Telnet authentication.
The Radius server and the shared secret needs to be
configured using CLI/Web/SNMP before enabling
RADIUS authentication.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vl: FBRM/BFFG Software Features
Transition Networks
Software security feature descriptions, continued
Table 4: Device Software Configurable Security Features (continued)
Description
Security Feature
Select Link-Pass
Through (LTP)
When enabled, a link change on Port 2 is passed on to
Port 1 (twisted pair). For example on a 10/100BaseT-to-
100Base FX Device, when the (monitored port) fiber
goes DOWN, LPT forces the twisted pair DOWN. The
LPT Port binding allows the user to choose which port to
monitor for LPT.
Note: In the redundant
models (SFBRM1040-
1xx) this feature only
works when the Device
is in redundant mode.
USB access
The USB port can be turned OFF to prevent
unauthorized access to the system.
Username/password for The username and password on the CLI (USB/Telnet) is
CLI
configurable and can be set by the administrator.
70
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section VIl:
Operations
Introduction
In this section
This section explains the operational status LEDs and what they indicate, along with
product features, and the three methods use to upgrade the firmware.
These are the topics:
Topic
See Page
Status LEDs
OAM Device management configuration options
Firmware upgrades
72
75
76
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vll: FBRM/BFFG Operation
Transition Networks
Status LEDs
Status
monitoring
LEDS
The FBRM series Devices are designed to operate without user intervention. Use the
status LEDs to monitor Device operation, once it has been installed in the network.
See Figure 59.
Figure 59: FBRM Device LEDs
LED status
tables
Tables 5, 6, and 7 explain the status of the power, USB, twisted pair (TP), and fiber
LEDs.
Table 5: Power and USB LEDs FBRM Devices
LEDs
Color
Green
Green
Status
Power
USB
ON has power/OFF no power
Blinking activity/OFF no activity
Table 6: TP Bi-Color LEDs FBRM Devices
TP LEDs Color
Yellow
Status
Half duplex TPLink/activity:
ON link, BLINK activity
Full duplex TPLink/activity:
ON link, BLINK activity
ON Link, blinking activity
ON Link, blinking activity
ON 10Mbs
Duplex
Green
Half Duplex/Link/Active Yellow
Full Duplex/Link/Active
Speed
Green
Yellow
Green
ON 100Mbs
Table 7: Fiber LEDs FBRM Devices
Fiber LEDs Color
Link Active Green
Duplex Green
Status
ON link, blinking activity
ON full, OFF half
Continued on next page
72
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section Vll: FBRM/BFFG Operation
Status LEDs, continued
Status
monitoring
LEDS
The BFFG copper-to-fiber Gbit series Devices are designed to operate without user
intervention. Use the status LEDs to monitor Device operation, once it has been
installed in the network. See Figure 60.
Figure 60: BFFG Device LEDs
LED status
tables
Tables 8, 9, and 10 explain the status of the power, USB, twisted pair (TP), and fiber
LEDs.
Table 8: Power and USB LEDs BFFG Devices
LEDs
Color
Green
Green
Status
Power
USB
ON has power/OFF no power
Blinking activity/OFF no activity
Table 9: Twisted Pair Bi-Color LEDs BFFG Devices
TP LEDs
Color
Yellow
Status
Half duplex TPLink/activity:
ON link, BLINK activity
Full duplex TPLink/activity:
ON link, BLINK activity
ON Link, blinking activity
ON Link, blinking activity
10Mbs
Duplex
Green
Half Duplex/Link/Active Yellow
Full Duplex/Link/Active
Speed
Green
OFF
Yellow
Green
ON 100Mbs
ON 1000 Mbs
Table 10: Fiber LEDs BFFG Devices
Fiber LEDs Color
Link Active Green
Duplex Green
Status
ON link, blinking activity
ON full, OFF half
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vll: FBRM/BFFG Operation
Transition Networks
Status LEDs, continued
Status
monitoring
LEDs
The FBRM Gbit and BFFG Gbit fiber series Devices are designed to operate without
user intervention. Use the status LEDs to monitor media-Device operation once
installed in the network. See Figure 61.
100Base-X
1000Base-X
PWR
LNK
DPX
LNK
USB
Power
LED
Duplex
LED
USB LED
Fiber Link
LED
Fiber Link
LED
1000Base-X
1000Base-X
LNK
PWR
LNK
USB
Power
LED
USB LED
Fiber Link
LED
Fiber Link
LED
Figure 61: CBFFG/CFBRM1xxx-xx Gbit Device LEDs
LED status
table (Gbit)
Tables 11 and 12 explain the status of the power, USB, link, duplex LEDs for Gbit
FBRM/BFFG Devices.
Table 11: Power and USB LEDs
LEDs
Color
Green
Green
Status
Power
USB
ON has power, OFF no power
Blinking activity, OFF no activity
Table 12: Fiber LEDs
Fiber-LEDs
Link
Duplex
Color
Green
Green
Status
ON link; blinking activity
ON full; OFF half (BFFG models only)
74
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section Vll: FBRM/BFFG Operation
OAM Device management configuration options
OAM mgmt.
configuration
options
OAM Mode control is a feature of the FBRM/BFFG Devices. It can be set to ‘Auto’
(default) or set manually (Active/Passive/Disabled):
• In ‘Auto’ Mode, the Device decides the OAM operation
• In Manual Mode, the user decides the OAM Mode (Active/Passive/Disabled)
Table 13 lists the default configuration.
Table 13: OAM Device Configurations
Chassis Device Standalone OAM Capability
Active
Active
Passive
Active
The active Device manages the passive Device.
The Devices exchange status information through
OAM, but cannot be managed through OAM.
The chassis Device needs to be in Active Mode since
it is being managed by the point system agent.
Management through ‘OAM and the chassis
simultaneously will cause configuration errors.
Passive
Active
Note: A chassis Device in a single slot chassis without the Point System agent
functions as a standalone Device.
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vll: FBRM/BFFG Operation
Transition Networks
Firmware upgrades
Introduction
The firmware image on the Device can be upgraded by these methods:
• TFTP protocol
• XModem
• OAM
When enabled, OAM is done automatically when the active peer detects that its
remotely managed peer is running a different version of the firmware. TFTP and
XModem are initiated by the user. All firmware upgrades are done by the
“bootloader.”
Note: The bootloader recognizes incompatible FBRM/BFFG BIN files when
upgrading. Since there are different FBRM/BFFG Device types, it is possible
that the user could download the wrong BIN file; when it receives an
incorrect file through TFTP or XMODEM, the following message will
appear on the screen:
Bootloader: Hardware and BIN file mismatch, upgrade
aborted.
XModem
method
To upgrade the firmware via XModem, do the following:
Step
Action
1.
At the console prompt> type xmodemupgrade
2.
Press the ENTER key and a decision prompt will appear as shown in
Figure 62.
Console:/>xmodemupgrade
Do you wish to proceed to upgrading (y/n):_
Figure 62: Decision Prompt for Firmware Upgrades
Note: If you select “Y,” the firmware image on the targeted Device will be erased.
Continued on next page
76
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section Vll: FBRM/BFFG Operation
Firmware upgrades, continued
XModem method (continued)
Step
3.
Action
Type “Y” at the prompt.
4.
Press the ENTER key to launch the firmware upgrade screen, shown in
Figure 63.
10/100BaseT to 100BaseFX IPBased 802.3ah Bridge
Version A
Copyright (c) 2006 Transition Networks
Reading config from flash........done
Erasing Application Memory
Start sending file through XModem...
Transfer completed
Checking CRC. . . . . . . .
Figure 63: Firmware Upgrade via Xmodem
5.
Choose the ‘send file’ option from Hyperterminal with ‘XModem’ as the
protocol. After the download, the bootloader verifies the CRC of the file
and resets itself to start the user application.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vll: FBRM/BFFG Operation
Transition Networks
Firmware upgrades, continued
The Device can be upgraded remotely using TFTP. A valid IP address, subnet,
TFTP method
gateway, TFTP server IP address, and filename must be configured before starting
the upgrade process.
TFTP can be started in the following ways:
• ‘tftpupgrade’ command at the CLI
• On the web using Æ “Local System Configuration” Æ ‘TFTP upgrade’
[perform(1)]
• Using SNMP, set ‘sfbrm100SysTFTPCmd’ to ‘1’ (perform)
After initiating the command, the system resets to start the bootloader, and then the
tftp upgrade will start. A message will appear like the example shown Figure 64.
10/100BaseT to 100BaseFX IPBased 802.3ah Bridge
Version A
Copyright (c) 2006 Transition Networks
Reading config from flash........done
Erasing Application Memory
Set to TFTP Boot from Server nnn.nnn.nnn.nnn
Getting File : FBRM.bin . . . . . . . . . . . done
Checking CRC. . . . . . . .
Figure 64: Firmware Upgrade via TFTP
After a successful upgrade, the application will start up.
Continued on next page
78
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section Vll: FBRM/BFFG Operation
Firmware upgrades, continued
OAM firmware upgrades are done by the local active peer Device to its remote
passive peer Device automatically. This occurs when the active peer Device finds that
its remote peer has a firmware revision different from its own. The active peer Device
sends a bootloader command to its remote peer. When the firmware upgrade on the
remote peer Device is completed, it will perform a “reset” to activate the new
firmware—no user intervention is required. (Active and passive peer relationships are
established during configuration.)
OAM method
What happens
when the
upgrade fails?
The FBRM/BFFG Devices can have a corrupted image for a variety of reasons. If the
image is corrupt, the following will occur: The bootloader checks the CRC to make
sure the image is good; if the check fails, it will re-initiate each method (XMODEM,
TFTP, OAM) in an attempt to accomplish the upgrade. The sequences is a follows:
Stage Description
A.
XMODEM will re-initiate if there is no input from the console; it will try
the OAM method.
B.
OAM initiates to locate an active peer on the network to get the upgrade
image; if an active peer is not available, it will try the TFTP method.
C.
D.
TFTP initiates a request to the TFTP server to get the upgrade image for
the Device.
This process continuously loops through these upgrade methods until one
of the methods successfully upgrades the firmware image.
Admin
intervention
To do a firmware upgrade from the console, before the bootloader moves to the next
method, it waits for ‘2’ seconds for user input displaying the following message:
“Moving to XMODEM upgrade, Hit 'ESC’ to skip or ctrl-C
for CLI.”
Bootloader CLI The “bootloader” has a CLI to configure network setting, such as the TFTP server
address, filename, and the boot method to use for upgrading the firmware.
The CLI can be started by pressing any key within ‘2’ seconds before it starts the
CRC validation, or by pressing the CTRL-C keys when it shows the following
message:
Transfer Failed
Moving to OAM, XMODEM or TFTP upgrade, Hit 'ESC' to skip/
<ctrl-c> for CLI.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vll: FBRM/BFFG Operation
Transition Networks
Firmware upgrades, continued
Accessing the
To access the bootloader CLI to upgrade the firmware, do the following:
bootloader CLI
Step
Action
1.
When “Transfer Failed” appears on the screen, within ‘2’
seconds, press the CTRL-C keys to bring up the bootloader CLI, as
shown in Figure 65.
10/100BaseT to 100BaseFX IP-Based 802.3ah Bridge
Version A [Mar 2 2006 09:56:02]
Copyright (c) 2006 Transition Networks
Reading config from flash........done.
BOOT LOADER CLI
Type 'h' for help
BOOT:>
Figure 65: Bootloader CLI
2.
At the BOOT:> prompt type the letter “h” to bring up the help screen,
shown in Figure 66.
h
p
Display this help
Ping a host
z
Clear entire Application flash
Set boot method as xmodem
Set boot method as tftp
Set boot method as OAM
Show system information
configure network information
reset system
x
t
o
s
n
r
q
Exit Boot CLI
BOOT:>
Figure 66: Bootloader Help Screen
Note: When you press the LETTER key of any command it might not appear at
the BOOT:> prompt, but the result will appear on the screen.
Continued on next page
80
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section Vll: FBRM/BFFG Operation
Firmware upgrades, continued
Accessing the bootloader CLI (continued)
Step
Action
At the BOOT:> prompt type the letter “t” to establish TFTP as the reboot
3.
method.
At the BOOT:> prompt type the letter “s” to view system information, as
4.
shown in Figure 67.
System configuration:
IP Address
Subnet Mask
Default Gateway
MAC Address
TFTP Server address
TFTP Filename
BOOT:>
: 192.251.144.150
: 255.255.255.0
: 192.251.144.2
: 00:c0:f2:00:d1:bc
: 0.0.0.0
:
Figure 67: System Configuration Information
5.
6.
If system configuration parameters are entered incorrectly or missing as
shown above, at the BOOT:> prompt type the letter “n.”
Press the ENTER key until the desired parameter appears on the screen
(TFTP Filename []). See Figure 68.
BOOT:>
Enter the Network configuration -
IP Address [192.251.144.150]:
Subnet Mask [255.255.255.0]:
Gateway [192.251.144.2]:
TFTP Server IP [0.0.0.0]:
TFTP Filename []:
Figure 68: Network Configuration Screen
7.
8.
Enter the necessary data.
When done, press the letter “r” key to reboot the Device. The firmware
image will be burned to flash memory of the Device. When completed,
the Device will reboot and return to the Login> prompt.
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section Vlll:
Troubleshooting
Introduction
This section provides basic troubleshooting information for the FBRM/BFFG Device
via a problem and corrective action table. The problems are stated in the problem
column and the action(s) to take for the problem is stated in the corrective action
column. If the corrective measures listed do not correct the problem, contact our 24-
Hour Technical Support department at 1-800-260-1312, International: 00-1-952-941-
7600.
In this section
These are the topics:
Topic
See Page
Troubleshooting problem and corrective action table
83
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vlll: FBRM/BFFG Troubleshooting
Transition Networks
Troubleshooting problem and corrective action table
Problem
Corrective Action
Device does not power
up
• Is the Device power LED ON?
• Is the power adapter’s barrel inserted fully into the Device?
• Is the power adapter plugged into an AC outlet?
• Is the AC outlet active; if not, check the outlet’s circuit breaker?
• Contact Technical Support. US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
Cannot detect or
communicate with the
xFBRM/xBFFG
• If CFBRM/CBFFG is in a cascaded chassis move the CFBRM/CBFFG
to the master chassis
• Upgrade to the latest version of firmware
• Contact Technical Support. US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
Cannot access the Device
via USB port
• Is the USB driver installed?
• Is the serial access disabled?
• Is the USB cable connected to the Device and to the host computer?
• Is the terminal emulator software configured properly for the USB port
and launched? See Driver Installation and COM Port Setup: Terminal
Emulator section.
• Contact Technical Support. US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
The local Device LACT
LED is ON but no data
transfer is detected (LED
flashing)
• Is the input source to the local Device active?
• Is the RJ-45 network cable fully inserted into the local Device, also into
the network Device?
• Is the fiber cable properly inserted into the local Device and the end
source Device?
• Contact Technical Support. US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
Ports do not link up
• Check the cable type needed for the Device and make sure the right
cable is used.
• Check Auto-Negotiation setting.
• Check if TPLT or remote fault-detect condition was triggered.
• Contact Technical Support. US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section Vlll: FBRM/BFFG Troubleshooting
Troubleshooting problem and corrective action table, continued
Problem
Corrective Action
The Trap Server does not
record traps
• Ensure the Trap Server application is running.
o
In the Windows environment, if the “TN” icon is displayed in the
lower right corner of the monitor, then the Trap Server is running.
• SNMP traps may be blocked by a router or firewall. Consult your
Network administrator to determine if this is the case.
• The SNMP trap manager may not be configured properly. The result is
that the SNMP agent does not know the proper IP address. Use the “set”
command to configure the trap manager. Enter the following command
on a single line:
CPSMM100> set=cpsmm100SNMPTrapMgr.<cabinet serial number>.<slot number of the
MM>,ip,<new IP Address of NMS>
• Alternatively, use the “getnext” command to “get” much of this
information and then use the “set=*” command to issue the set request.
The following is an example. Enter “Super-User Mode”:
CPSMM100> su=<private community name>
[su] CPSMM>
Enter the “getnext” command:
[su] CPSMM100> getnext=cpsmm100snmptrapmgr
The response is:
SNMP: GETNEXT [192.251.144.229] id=D2EE6F3F ind=0 cpsmm100snmptrapmgr.1758208.1
1P Address [4/0x4] 192.251.144.235
Enter the set request:
[su] CPSMM100> set=*,ip,172.16.45.105
The response is:
SNMP: SET [192.251.144.229] id=D2EE6F3F ind=0 cpsmm100SNMPTrapMgr.1758208.1
IP Address [4/0x4] 172.16.45.105
Save the changes:
[su] CPSMM100> save
Continued on next page
84
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vlll: FBRM/BFFG Troubleshooting
Transition Networks
Troubleshooting problem and corrective action table, continued
Problem
Corrective Action
The Trap Server does not
record traps,(continued)
The response is:
FLASH: Saving configuration, please wait up to one minute...
Writing Flash (04004500,05E8,00FE0000,00FFFFFE)
Erasing
.
Done Erasing/Verifying
Writing [000005E8]
#[0000FFFF]
Done Writing
Verifying
FLASH: Write complete.
Cannot activate IP-based
management
• Are the IP, Gateway, and subnet mask configured correctly?
• With DHCP enabled, DHCP could have failed leaving the system with
the old static IP config. Verify the configuration via the USB port.
• Make sure IP-based access is not turned OFF in the system.
• Contact Technical Support. US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
TLPT and SLDP are not
working
• Are the TLPT and SLDP enabled on both systems? Refresh web pages
to make sure they are set.
• Check if port binding for TLPT/RFD is set to the active OAM channel.
• With 100Base-Fx, make sure “far end fault” is enabled.
• Contact Technical Support. US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
OAM session is not
active
• If OAM is enabled, check the ports on the local and remote Devices.
• Make sure the local Device is in OAM “Active” Mode.
OAM remote Device is
detected on local, but
cannot configure remote
from local
• Make sure the remote peer Device is set to “Passive” Mode.
Note: OAM session can be formed between Devices with both set to
Active Mode, but this prevents remote management. The remote
Device should be in “Passive” Mode for management.
• Contact Technical Support. US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section Vlll: FBRM/BFFG Troubleshooting
Troubleshooting problem and corrective action table, continued
Problem
Corrective Action
• If the OAM session is active, the active local peer Device sends
configuration information; if the user attempts to go directly to the
remote passive peer Device, the configuration will be overwritten by the
OAM update from the local active peer. It is advisable to always use the
local active peer Device to manage its remote passive peer Device.
Unable to do
configuration directly
using IP based
management on Remote
Device
• Contact Technical Support. US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
Chassis FBRM/BFFG
not recognized by the
chassis agent
• Make sure the Point System agent has the latest firmware version for the
CFBRM/CBFFG Device. Use the FEATSUPP command to see if the
Devices are supported.
• Contact Technical Support. US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
Chassis FBRM/BFFG is
in a single-slot chassis,
but the Port 2 comes up
in OAM “Passive” Mode
with OAM Mode control
is set to ‘auto’
• The chassis Devices in single-slot chassis function as a standalone
Device.
• Chassis Device needs a Point System management module in a chassis
to switch to “Active” Mode, or to set OAM Mode manually.
• Contact Technical Support. US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
86
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Vlll: FBRM/BFFG Troubleshooting
Transition Networks
Intentionally Blank
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lX:
Copper Cable & Fiber Optic Specifications
Introduction
This section provides copper and fiber cable specifications.
These are the topics:
In this section
Topic
Copper cables
Fiber optic cables and connectors
See Page
89
90
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Transition Networks
Copper cables
Characteristics Cooper cable physical characteristics must meet or exceed IEEE 802.3™
specifications.
Copper cable
specification
Category 5:
Gauge:
minimum
24 to 22 AWG
Attenuation:
22.0 dB/100m @ 100 MHz
Maximum cable distance: 100 meter (328 ft.)
• Straight-through or crossover twisted-pair cable may be used. See Figure 69.
• Shielded twisted-pair (STP) or unshielded twisted-pair (UTP) may be used.
• Pins 1&2 and 3&6 are the two active pairs in an Ethernet network.
• RJ-45 pin-outs on MDI cable: Pin 1 = TD+, Pin 2 = TD-, Pin 3 = RD+, Pin 6 =
RD-
• Use only dedicated wire pairs for the active pins.
(e.g., blue/white & white/blue, orange/white & white/orange, etc.)
• DO NOT use flat or silver satin wire.
Figure 69: MDI Straight Through and MDI-X Crossover Cables
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Fiber optic cable and connector specifications
Fiber cable
Cable physical characteristics must meet or exceed IEEE 802.3™ specifications.
characteristics
Parameter
Specification
Bit Error Rate:
<10-9
Single mode fiber:
Multimode fiber:
Multimode fiber:
9 µm
62.5/125 µm
100/140, 85/140, 50/125 µm
Copper-to-fiber The following are FBRM10xx-1xx copper-to-fiber connector specifications.
connectors
Fiber Optics
Specifications
CFBRM1011-100
SFBRM1011-100
1300 nm multimode
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
min: -19.0 dBm max: -14.0 dBm
min: -30.0 dBm max: -14.0 dBm
11 dB
CFBRM1013-100
SFBRM1013-100
1300 nm multimode
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
min: -19.0 dBm max: -14.0 dBm
min: -30.0 dBm max: -14.0 dBm
11 dB
CFBRM1014-100
SFBRM1014-100
1310 nm single mode
min: -15.0 dBm max: -8.0 dBm
min: -31.0 dBm max: -8.0 dBm
16 dB
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
CFBRM1015-100 (long haul)
SFBRM1015-100 (long haul)
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1310 nm single mode
min: -8.0 dBm max: -2.0 dBm
min: -34.0 dBm max: -7.0 dBm
26 dB
WARNING: Visible and invisible laser radiation when open. Do not stare into the
beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Continued on next page
90
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Transition Networks
Fiber optic cable and connector specifications, continued
Copper-to-fiber connectors (continued)
Fiber Optics
Specifications
1310 nm single mode
min: -5.0 dBm max: 0.0 dBm
min: -34.0 dBm max: -7.0 dBm
29 dB
CFBRM1016-100 (extra long haul)
SFBRM1016-100 (extra long haul)
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
CFBRM1017-100 (long wave length)
SFBRM1017-100 (long wave length) 1550 nm single mode
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
min: -5.0 dBm max: 0.0 dBm
min: -34.0 dBm max: -7.0 dBm
29 dB
CFBRM1035-100
SFBRM1035-100
1550 nm single mode
min: -0.0 dBm max: 5.0 dBm
min: -36.0 dBm max: -3.0 dBm
36 dB
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
CFBRM1029-100
CFBRM1029-101
SFBRM1029-100
SFBRM1029-101
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1310 nm (TX)/1550 nm (RX) simplex
1550 nm (TX)/1310 nm (RX) simplex
1310 nm (TX)/1550 nm (RX) simplex
1550 nm (TX)/1310 nm (RX) simplex
min: -14.0 dBm max: -8.0 dBm
min: -33.0 dBm max: -3.0 dBm
19 dB
CFBRM1029-102
CFBRM1029-103
SFBRM1029-102
SFBRM1029-103
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1310 nm (TX)/1550 nm (RX) simplex
1550 nm (TX)/1310 nm (RX) simplex
1310 nm (TX)/1550 nm (RX) simplex
1550 nm (TX)/1310 nm (RX) simplex
min: -8.0 dBm max: -3.0 dBm
min: -33.0 dBm max: -3.0 dBm
25 dB
Note: The fiber optic transmitters on these Devices meet Class I Laser safety
requirements per IEC-825/CDRH standards and comply with 21
CFR1040.10 and 21CFR1040.11.
WARNING: Visible and invisible laser radiation when open. Do not stare into the
beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Fiber optic cable and connector specifications, continued
Copper-to-Copper-to-fiber connectors with DMI
Fiber Optics
Specifications
CFBRM1011-110 DMI
SFBRM1011-110 DMI
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1300 nm multimode
min: -19.0 dBm max: -14.0 dBm
min: -30.0 dBm max: -14.0 dBm
11 dB
CFBRM1013-110 DMI
SFBRM1013-110 DMI
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1300 nm multimode
min: -19.0 dBm max: -14.0 dBm
min: -30.0 dBm max: -14.0 dBm
11 dB
CFBRM1014-110 DMI
SFBRM1014-110 DMI
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1310 nm single mode
min: -15.0 dBm max: -8.0 dBm
min: -31.0 dBm max: -8.0 dBm
16 dB
CFBRM1015-110 DMI (long haul)
SFBRM1015-110 DMI(long haul)
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1310 nm single mode
min: -8.0 dBm max: -2.0 dBm
min: -34.0 dBm max: -7.0 dBm
26 dB
CFBRM1016-110 DMI
SFBRM1016-110 DMI
(extra long haul)
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1310 nm single mode
min: -5.0 dBm max: 0.0 dBm
min: -34.0 dBm max: -7.0 dBm
29 dB
CFBRM1017-110 DMI
SFBRM1017-110 DMI
(long wave length)
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1550 nm single mode
min: -5.0 dBm max: 0.0 dBm
min: -34.0 dBm max: -7.0 dBm
29 dB
CFBRM1035-110 DMI
SFBRM1035-110 DMI
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1550 nm single mode
min: -0.0 dBm max: 5.0 dBm
min: -36.0 dBm max: -3.0 dBm
36 dB
Continued on next page
92
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Transition Networks
Fiber optic cable and connector specifications, continued
Copper-to-fiber connectors with DMI (continued)
Fiber Optics
Specifications
1310 nm (TX)/1550 nm (RX) simplex
CFBRM1029-110 DMI
CFBRM1029-111 DMI
SFBRM1029-110 DMI
SFBRM1029-111 DMI
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1550 nm (TX)/1310 nm (RX) simplex
1310 nm (TX)/1550 nm (RX) simplex
1550 nm (TX)/1310 nm (RX) simplex
min: -14.0 dBm max: -8.0 dBm
min: -33.0 dBm max: -3.0 dBm
19 dB
CFBRM1029-112 DMI
CFBRM1029-113 DMI
SFBRM1029-112 DMI
SFBRM1029-113 DMI
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
1310 nm (TX)/1550 nm (RX) simplex
1550 nm (TX)/1310 nm (RX) simplex
1310 nm (TX)/1550 nm (RX) simplex
1550 nm (TX)/1310 nm (RX) simplex
min: -8.0 dBm max: -3.0 dBm
min: -33.0 dBm max: -3.0 dBm
25 dB
Note: The fiber optic transmitters on these Devices meet Class I Laser safety
requirements per IEC-825/CDRH standards and comply with 21
CFR1040.10 and 21CFR1040.11.
WARNING: Visible and invisible laser radiation when open. Do not stare into the
beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Fiber optic cable and connector specifications, continued
FBRM fiber-to-fiber Gbit connector
Fiber Optics
Port 1 Specification
Port 2 Specification
CFBRM1313-100
SFBRM1313-100
1310 nm multimode
850 nm multimode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -10.0 dBm max: -14.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -17.0 dBm max: 0.0 dBm
Link budget:
11 dB
7 dB
CFBRM1314-100
SFBRM1314-100
1310 nm multimode
1310 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -13.0 dBm max: -3.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -20.0 dBm max: -3.0 dBm
Link budget:
11 dB
7 dB
CFBRM1315-100
SFBRM1315-100
1310 nm multimode
1310 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -5.0 dBm max: 0.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -20.0 dBm max: -3.0 dBm
Link budget:
11 dB
15 dB
CFBRM1317-100
SFBRM1317-100
1310 nm multimode
1550 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -3.0 dBm max: 2.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -24.0 dBm max: -3.0 dBm
Link budget:
11 dB
21 dB
CFBRM1329-100
CFBRM1329-101
SFBRM1329-100
SFBRM1329-101
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1310 nm multimode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -8.0 dBm max: 3.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -22.0 dBm max: -3.0 dBm
Link budget:
11 dB
14 dB
CFBRM1329-102
CFBRM1329-103
SFBRM1329-102
SFBRM1329-103
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1310 nm multimode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -3.0 dBm max: 2.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -23.0 dBm max: -3.0 dBm
Link budget:
11 dB
20 dB
Note: The fiber optic transmitters on these Devices meet Class I Laser safety
requirements per IEC-825/CDRH standards and comply with 21
CFR1040.10 and 21CFR1040.11.
Continued on next page
94
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Transition Networks
Fiber optic cable and connector specifications, continued
FBRM fiber-to-fiber Gbit connectors(continued)
Fiber Optics
CFBRM1335-100
SFBRM1335-100
Port 1 Specification
Port 2 Specification
1550 nm single mode
1310 nm multimode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: 0.0 dBm max: 5.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -27.0 dBm max: -3.0 dBm
Link budget:
11 dB
27 dB
FBRM fiber-to-fiber Gbit with DMI connectors
Fiber Optics
Port 1 Specification
Port 2 Specification
CFBRM1313-110 DMI
SFBRM1313-110 DMI
1300 nm multimode
850nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -9.5 dBm max: -4.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -18.0 dBm max: -3.0 dBm
Link budget:
11 dB
8.5 dB
CFBRM1314-110 DMI
SFBRM1314-110 DMI
1300 nm multimode
1310 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -9.0 dBm max: -3.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -21.0 dBm max: -3.0 dBm
Link budget:
11 dB
12 dB
CFBRM1315-110 DMI
SFBRM1315-110 DMI
1300 nm multimode
1310 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -5.0 dBm max: 0.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -24.0 dBm max: -3.0 dBm
Link budget:
11 dB
19 dB
CFBRM1329-110 DMI
CFBRM1329-111 DMI
SFBRM1329-110 DMI
SFBRM1329-111 DMI
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1300 nm multimode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -9.0 dBm max: 3.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -20.0 dBm max: -3.0 dBm
Link budget:
11 dB
11 dB
CFBRM1329-112 DMI
CFBRM1329-113 DMI
SFBRM1329-112 DMI
SFBRM1329-113 DMI
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1300 nm multimode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -9.0 dBm max: 3.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -20.0 dBm max: -3.0 dBm
Link budget:
11 dB
11 dB
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Fiber optic cable and connector specifications, continued
Copper-to-fiber The following are BFFG10x40-100 copper-to-fiber connector specifications.
connectors
Fiber Optics
Specifications
CBFFG1040-100
SBFFG1040-100
Empty Slot
Fiber-optic transmitter power:
Fiber-optic receiver sensitivity:
Link budget:
Note: The fiber optic transmitters on these Devices meet Class I Laser safety
requirements per IEC-825/CDRH standards and comply with 21
CFR1040.10 and 21CFR1040.11.
WARNING: Visible and invisible laser radiation when open. Do not stare into the
beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Continued on next page
96
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Fiber optic cable and connector specifications, continued
BFFG fiber-to-fiber Gbit connectors
Transition Networks
Fiber Optics
CBFFG1313-100
SBFFG1313-100
Port 1 Specification
Port 2 Specification
850 nm single mode
1300 nm multimode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -10.0 dBm max: -14.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -17.0 dBm max: 0.0 dBm
Link budget:
11 dB
7 dB
CBFFG1314-100
SBFFG1314-100
1300 nm multimode
1310 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -13.0 dBm max: -3.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -20.0 dBm max: -3.0 dBm
Link budget:
11 dB
7 dB
CBFFG1315-100
SBFFG1315-100
1300 nm multimode
1310 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -5.0 dBm max: 0.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -20.0 dBm max: -3.0 dBm
Link budget:
11 dB
15 dB
CBFFG1317-100
SBFFG1317-100
1300 nm multimode
1310 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -3.0 dBm max: 2.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -24.0 dBm max: -3.0 dBm
Link budget:
11 dB
21 dB
CBFFG1329-100
CBFFG1329-101
SBFFG1329-100
SBFFG1329-101
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1300 nm multimode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -8.0 dBm max: 3.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -22.0 dBm max: -3.0 dBm
Link budget:
11 dB
14 dB
CBFFG1329-102
CBFFG1329-103
SBFFG1329-102
SBFFG1329-103
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1300 nm multimode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -3.0 dBm max: 2.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -23.0 dBm max: -3.0 dBm
Link budget:
11 dB
20 dB
Note: The fiber optic transmitters on these Devices meet Class I Laser safety
requirements per IEC-825/CDRH standards and comply with 21
CFR1040.10 and 21CFR1040.11.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Fiber optic cable and connector specifications, continued
BFFG fiber-to-fiber Gbit connector (continued)
Fiber Optics
Port 1 Specification
Port 2 Specification
CBFFG1335-100
SBFFG1335-100
1300 nm multimode
1310 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: 0.0 dBm max: 5.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -27.0 dBm max: -3.0 dBm
Link budget:
11 dB
27 dB
BFFG fiber-to-fiber Gbit with DMI connector
Fiber Optics
Port 1 Specification
Port 2 Specification
CBFFG1313-110 DMI
SBFFG1313-110 DMI
1300 nm multimode
1310 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -9.5 dBm max: -4.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -18.0 dBm max: -3.0 dBm
Link budget:
11 dB
8.5 dB
CBFFG1314-110 DMI
SBFFG1314-110 DMI
1300 nm multimode
1310 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -9 dBm max: -3.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -21.0 dBm max: -3.0 dBm
Link budget:
11 dB
12 dB
CBFFG1315-110 DMI
SBFFG1315-110 DMI
1300 nm multimode
1310 nm single mode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -5 dBm max: 0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -24.0 dBm max: -3.0 dBm
Link budget:
11 dB
19 dB
CBFFG1329-110 DMI
CBFFG1329-111 DMI
SBFFG1329-110 DMI
SBFFG1329-111 DMI
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1300 nm multimode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -9.0 dBm max: 3.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -20.0 dBm max: -3.0 dBm
Link budget:
11 dB
11 dB
Note: The fiber optic transmitters on these Devices meet Class I Laser safety
requirements per IEC-825/CDRH standards and comply with 21
CFR1040.10 and 21CFR1040.11.
WARNING: Visible and invisible laser radiation when open. Do not stare into the
beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Continued on next page
98
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Transition Networks
Fiber optic cable and connector specifications, continued
BFFG fiber-to-fiber Gbit with DMI connector (continued)
Fiber Optics
Port 1 Specification
Port 2 Specification
CBFFG1329-112 DMI
CBFFG1329-113 DMI
SBFFG1329-112 DMI
SBFFG1329-113 DMI
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1310 nm (TX)/1490 nm (RX)
1490 nm (TX)/1310 nm (RX)
1300 nm multimode
Fiber-optic transmitter power: min: -19.0 dBm max: -14.0 dBm min: -9.0 dBm max: 3.0 dBm
Fiber-optic receiver sensitivity: min: -30.0 dBm max: -14.0 dBm min: -20.0 dBm max: -3.0 dBm
Link budget:
11 dB
11 dB
Note: The fiber optic transmitters on these Devices meet Class I Laser safety
requirements per IEC-825/CDRH standards and comply with 21
CFR1040.10 and 21CFR1040.11.
WARNING: Visible and invisible laser radiation when open. Do not stare into the
beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section lX: FBRM/BFFG Cable & Fiber Optic Specifications
Intentionally Blank
100
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section X:
Contact Us, Warranty, & Conformity Information
Introduction
This section explains how to contact Transition Networks via Phone, fax, email, and
direct mail. It also explains:
• What the warranty covers
• Who to contact to return product
• How and where to return the product
In this section
These are the topics:
Topic
See Page
102
Contact us
Conformity declaration
Warranty
103
105
Compliance information
107
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section X: FBRM/BFFG Contact Us, Warranty, & Conformity Information
Contact us
Technical
support
Technical Support is available 24 hours a day.
United States: 1-800-260-1312
International: 00-1-952-941-7600
Live Web chat
Chat live via the Web with a Transition Networks Technical Support Specialist.
Log onto www.transition.com and click the Transition Now link.
Web-based
training
Transition Networks provides 12-16 seminars per month via live web-based training.
Log onto www.transition.com and click the Learning Center link.
E-Mail
Ask a question anytime by sending an e-mail message to our technical support staff:
Address
Transition Networks
10900 Red Circle Drive
Minnetonka, MN 55343, U.S.A.
Telephone:
952-941-7600
800-526-9267
952-941-2322
Toll free U.S.A & Canada:
Fax:
102
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Section X: FBRM/BFFG Contact Us, Warranty, & Conformity Information
Conformity declaration
Transition Networks
Declaration of Conformity
Name of Mfg:
Transitions Networks
6427 City West Parkway, Minneapolis MN 55344 U.S.A.
Model:
xFBRM1xxx-1xx and xBFFG1xxx-1xx Media
Part Numbers:
CFBRM1011-100, CFBRM1013-100, CFBRM1014-100,
CFBRM1015-100, CFBRM1016-100, CFBRM1017-100,
CFBRM1035-100, CFBRM1040-100, CFBRM1029-100,
CFBRM1029-101, CFBRM1029-102, CFBRM1029-103
CFBRM1011-110, CFBRM1013-110, CFBRM1014-110,
CFBRM1015-110, CFBRM1016-110, CFBRM1017-110,
CFBRM1035-110, CFBRM1040-110, CFBRM1029-110,
CFBRM1029-111, CFBRM1029-112, CFBRM1029-113,
CFBRM1313-100, CFBRM1314-100, CFBRM1315-100,
CFBRM1317-100, CFBRM1035-110, CFBRM1040-100,
CFBRM1029-100, CFBRM1029-100, CFBRM1029-100,
CFBRM1029-100
CFBRM1313-110, CFBRM1314-110, CFBRM1315-110,
CFBRM1317-110, CFBRM1035-110, CFBRM1040-110,
CFBRM1029-110, CFBRM1029-111, CFBRM1029-112,
CFBRM1029-113
SFBRM1011-100, SFBRM1013-100, SFBRM1014-100,
SFBRM1015-100, SFBRM1016-100, SFBRM1017-100,
SFBRM1035-100, SFBRM1040-100, SFBRM1029-100,
SFBRM1029-101, SFBRM1029-102, SFBRM1029-103
SFBRM1011-110, SFBRM1013-110, SFBRM1014-110,
SFBRM1015-110, SFBRM1016-110, SFBRM1017-110,
SFBRM1035-110, SFBRM1040-110, SFBRM1029-110,
SFBRM1029-111, SFBRM1029-112, SFBRM1029-113,
SFBRM1313-100, SFBRM1314-100, SFBRM1315-100,
SFBRM1317-100, SFBRM1335-110, SFBRM1340-100,
SFBRM1329-100, SFBRM1029-100, SFBRM1329-100,
SFBRM1329-100
SFBRM1313-110, CFBRM1314-110, SFBRM1315-110,
SFBRM1317-110, CFBRM1335-110, SFBRM1340-110,
SFBRM1329-110, CFBRM1329-111, CFBRM1329-112,
SFBRM1329-113
CBFFG1013-100, CBFFG1014-100, CBFFG1015-100,
CBFFG1017-100, CBFFG1024-100, CBFFG1035-100,
CBFFG1040-100, CBFFG1029-100, CBFFG1029-101,
CBFFG1029-102, CBFFG1029-103
CBFFG1313-100, CBFFG1314-100, CBFFG1315-100,
CBFFG1317-100, CBFFG1335-100, CBFFG1340-100,
CBFFG1329-100, CBFFG1329-101, CBFFG1329-102,
CBFFG1029-103
CBFFG1313-110, CBFFG1314-110, CBFFG1315-110,
CBFFG1317-110, CBFFG1335-110, CBFFG1340-110,
CBFFG1329-100, CBFFG1329-111, CBFFG1329-112,
CBFFG1029-113
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section X: FBRM/BFFG Contact Us, Warranty, & Conformity Information
Conformity declaration, continued
SBFFG1313-100, SBFFG1314-100, SBFFG1315-100,
SBFFG1317-100, SBFFG1335-100, SBFFG1340-100,
SBFFG1329-100, SBFFG1329-101, SBFFG1329-102,
SBFFG1029-103
SBFFG1313-110, SBFFG1314-110, SBFFG1315-110,
SBFFG1317-110, SBFFG1335-110, SBFFG1340-110,
SBFFG1329-110, SBFFG1329-111, CBFFG1329-112,
SBFFG1029-113
Regulations:
EMC Directive 89/336/EEC
Purpose:
To declare that the CFBRM1xxx-1xx, SFBRM1xxx-1xx, CBFFG1xxx-1xx and
SBFFG1xxx-1xx Devices to which this declaration refers is in conformance with
the following standards:
CISPR22:1993; EN55022:1994+A1:1995+A2:1997 Class A; FCC Part 15
Subpart B; UL1950; 21 CFR Subpart J
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
July, 2008
Steven Anderson, Vice President of Engineering
Date
104
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Section X: FBRM/BFFG Contact Us, Warranty, & Conformity Information
Transition Networks
Warranty
Limited lifetime Effective for products shipped May 1, 1999 and after. Every Transition Networks’
warranty
labeled product purchased after May 1, 1999 will be free from defects in material
and workmanship for its lifetime. This warranty covers the original user only and is
not transferable.
What the
warranty does
not cover
This warranty does not cover damage from accident, acts of God, neglect,
contamination, misuse or abnormal conditions of operation or handling, including
over-voltage failures caused by use outside the product's specified rating, or normal
wear and tear of mechanical components. If the user is unsure of the proper means of
installing or using the equipment, contact Transition Networks' free technical support
services.
Establishing
original
ownership
To establish original ownership and provide date of purchase, please complete and
return the registration card accompanying the product or register the product on-line
on our product registration page.
Transition Networks will at its option:
• Repair the defective product to functional specifications at no charge
• Replace the product with an equivalent functional product
• Refund the purchase price of a defective product
Who to contact To return a defective product for warranty coverage, contact Transition Networks'
for returns
technical support department for a return authorization number (RAN). Transition's
technical support department can be reached through any of the following means:
Technical Support is available 24 hours a day:
• Tel: 800-260-1312 x200 or 952-941-7600 x200
• Fax: 952-941-2322
• Email: [email protected]
• Live web chat: Transition Now
• Voicemail: 800-260-1312, x579 or 952-941-7600, x579
• All messages will be answered within one hour
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section X: FBRM/BFFG Contact Us, Warranty, & Conformity Information
Warranty, continued
How and where Send the defective product postage and insurance prepaid to the following address:
to send the
returns
CSI Material Management Center
c/o Transition Networks
6103 Blue Circle Drive
Minnetonka, MN 55343, U.S.A.
Attn: RETURNS DEPT: Credit Return Authorization (CRA)# or Return Material
Authorization (RMA) # ___________
Failure to protect the product during shipping may void this warranty. The return
authorization number must be written on the outside of the carton to ensure its
acceptance. We cannot accept delivery of any equipment sent to us without a CRA or
RMA number.
Customer pays The customer must pay the non-compliant product(s) return transportation cost to
non-compliant
return costs
Transition Networks for evaluation of said product(s) for repair or replacement.
Transition Networks will pay for shipping the repaired or replaced in-warranty
product(s) back to the customer (any and all customs charges, tariffs, or/and taxes
are the customer's responsibility).
Non-warranty
repair costs
Before making any non-warranty repair, Transition Networks requires a $200
charge, plus actual shipping costs to and from the customer. If the repair is greater
than $200, an estimate is issued to the customer for authorization before making the
repair. If no authorization is obtained, or the product is deemed not repairable,
Transition Networks will retain the $200 service charge and return the product to the
customer not repaired.
Repaired non-
warranty
products
Non-warranted products repaired by Transition Networks for a fee will carry a 180-
day limited warranty. All warranty claims are subject to the restrictions and
conventions set forth by this document.
Transition Networks reserves the right to charge for all testing and shipping incurred,
if after testing, a return is classified as "No Problem Found."
This warranty
is your only
remedy
This warranty is your only remedy. No other warranties, such as fitness for a
particular purpose, are expressed or implied. Transition Networks is not liable for
any special, indirect, incidental or consequential damages or losses, including loss of
data, arising from any cause or theory. Authorized resellers are not authorized to
extend any different warranty on transition networks' behalf.
106
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Section X: FBRM/BFFG Contact Us, Warranty, & Conformity Information
Transition Networks
Compliance information
Standards
CISPR22/EN55022 Class A, CE Mark
FCC
Regulations
This equipment has been tested and found to comply with the limits for a Class A
digital Device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at the
user's own expense.
Canadian
Regulations
This digital apparatus does not exceed the Class A limits for radio noise from digital
apparatus set out on the radio interference regulations of the Canadian Department of
Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la Class A prescrites dans le
Règlement sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada.
European
WARNING:
Regulations
This is a Class A product. In a domestic environment, this product could cause radio
interference in which case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei
Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer
für Gegenmaßnahmen verantwortlich.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque
de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de
prende les measures spécifiques appropriées.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Section X: FBRM/BFFG Contact Us, Warranty, & Conformity Information
Compliance information, continued
European
In accordance with European Union Directive 2002/96/EC of the
Regulations,
(continued)
European Parliament and of the Council of 27 January 2003, Transition
Networks will accept post usage returns of this product for proper disposal.
The contact information for this activity can be found in the 'Contact Us'
portion of this document.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO
THE PUBLIC TELEPHONE NETWORK. Failure to observe this caution
could result in damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den
EG-Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur
Anwendung der Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der
Mitgliedstaaten über Telekommunikationsendeinrichtungen einschliesslich der
gegenseitigen Anerkennung ihrer Konformität.
108
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix A:
FBRM/BFFG Part Numbers
FBRM copper-to-fiber part numbers
Standard
models
The models shown in Table 14 perform as described in this manual. The 110 in the
model designation means DMI functionality.
Table 14: FBRM10xx-1xx Model Numbers
Port 1: Copper
10/100Base-T
RJ-45
Port 2: Fiber
100Base-FX
ST, 100Base-FX 1300nm
MM
Part Number
CFBRM1011-100
CFBRM1011-110 DMI
SFBRM1011-100
100m (328ft)
2 km (1.2 miles)
SFBRM1011-110 DMI
CFBRM1013-100
CFBRM1013-110 DMI
SFBRM1013-100
RJ-45
100m (328ft)
SC, 100Base-FX 1300nm
MM
2 km (1.2 miles)
SFBRM1013-110 DMI
CFBRM1014-100
CFBRM1014-110 DMI
SFBRM1014-100
RJ-45
100m (328ft)
SC, 100Base-LX10 1310nm
SM
10 km (6.2 miles)
SFBRM1014-110 DMI
CFBRM1015-100
CFBRM1015-110 DMI
SFBRM1015-100
RJ-45
100m (328ft)
SC, 100Base-FX 1310nm
SM
40 km (24.9 miles)
SFBRM1015-110 DMI
(long haul)
CFBRM1016-100
CFBRM1016-110 DMI
SFBRM1016-100
RJ-45
100m (328ft)
SC, 100Base-FX 1310nm
SM
60 km (37.3 miles)
SFBRM1016-110 DMI
(extra long haul)
CFBRM1017-100
CFBRM1017-110 DMI
SFBRM1017-100
RJ-45
100m (328ft)
SC, 100Base-FX 1550nm
SM
80 km (49.7 miles)
SFBRM1017-110 DMI
(long wave)
CFBRM1035-100
CFBRM1035-110 DMI
SFBRM1035-100
RJ-45
100m (328ft)
SC, 100Base-FX 1550nm
SM
120km (74.6 miles)
SFBRM1035-110 DMI
(long wave length)
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix A: FBRM/BFFG Part Numbers
FBRM copper-to-fiber part numbers, continued
Single-fiber
model pairs
The models shown in Table 15 are single-fiber and must be installed in pairs.
Table 15: FBRM10xx-1xx Single-Fiber Model Pairs
Port 1: Copper
10/100Base-T
RJ-45
Port 2: Fiber
100Base-FX
SC, 100Base-FX BX-U 1310 nm
TX/1550nm RX
Part Number
CFBRM1029-100**
CFBRM1029-110** DMI
SFBRM1029-100**
100m (328ft)
SM
SFBRM1029-110** DMI
CFBRM1029-101**
CFBRM1029-111** DMI
SFBRM1029-101**
20 km (12.4 miles)
SC, 100Base-FX BX-D 1550 nm
TX/1310 nm RX
SM
RJ-45
100m (328ft)
SFBRM1029-111** DMI
CFBRM1029-102***
CFBRM1029-112*** DMI 100m (328ft)
SFBRM1029-102***
20 km (12.4 miles)
SC, 100Base-FX BX-U 1310 nm
TX/1550nm RX
RJ-45
SM
SFBRM1029-112*** DIM
CFBRM1029-103***
CFBRM1029-113*** DMI 100m (328ft)
SFBRM1029-103***
40 km (24.9 miles)
SC, 100Base-FX BX-D 1550 nm
TX/1310nm RX
RJ-45
SM
SFBRM1029-113*** DMI
40 km (24.9 miles)
BX-D (down stream) BX-U (up stream)
Note: The distances for Port 1 listed in Table 15 are typical maximum distances; the
physical characteristics of the network dictate actual distances.
**FBRM-100 and -101, -110 and -111 Device pairs require installation in the same
network, where one is the local Device and the other its remote peer.
***FBRM-102 and -103, -112 and -113 Device pairs require installation in the same
network, where one is the local Device and the other its remote peer.
Continued on next page
110
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: FBRM/BFFG Part Numbers
Transition Networks
FBRM copper-to-fiber part numbers, continued
SFP models
The models shown in Table 16 use SFP (small form factor pluggable) Devices sold
separately from Transition networks.
Table 16: FBRM1040-1xx (SFP Models)
Part Number
Port 1: Copper 10/100Base-T Port 2: Empty
RJ-45 100m (328ft) Empty SFP slot*
CFBRM1040-100
CFBRM1040-110 DMI
SFBRM1040-100
SFBRM1040-110 DMI
Note: The distances for Port 1 listed in Table 21 are typical maximum distances; the
physical characteristics of the network dictate actual distances.
*Compatible SFP transceiver Devices for the FBRM1040-1xx Devices are available
from Transition Networks (sold separately). See the TN-SFP-xxx series SFP manual
# 33308 at www.transiton.com for available options.
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix A: FBRM/BFFG Part Numbers
FBRM fiber-to-fiber part numbers
FBRM Gbit
models
The models shown in Table 17 are dual-fiber port models. The 11x in the model
designation means DMI functionality.
Table 17: FBRM13xx-1xx Gbit Models
Port 1: Fiber
100Base-FX
Port 2: Fiber
1000Base-SX/LX
Part Number
CFBRM1313-100
100Base-FX 1300 nm
SC, 1000Base-SX 850 nm
CFBRM1313-110 DMI
SFBRM1313-100
MM SC 2Km (1.2 miles) MM
300/500 m (985/1,640 ft)
SFBRM1313-110 DMI
CFBRM1314-100
CFBRM1314-110 DMI
SFBRM1314-100
100Base-FX 1300 nm
MM SC 2Km (1.2 miles) SM
10 Km (6.2 miles)
SC, 1000Base-LX 1310 nm
SFBRM1314-110 DMI
CFBRM1315-100
CFBRM1315-110 DMI
SFBRM1315-100
100Base-FX 1300 nm
MM SC 2Km (1.2 miles) SM
25 km (15.5 miles)
SC, 1000Base-LX 1310 nm
SFBRM1315-110 DMI
CFBRM1317-100
CFBRM1317-110 DMI
SFBRM1317-100
100Base-FX 1300 nm
MM SC 2Km (1.2 miles) SM
65 km (40.3 miles)
SC, 1000Base-LX 1310 nm
SFBRM1317-110 DMI
CFBRM1335-100
SFBRM1335-110 DMI
CFBRM1335-100
100Base-FX 1300 nm
MM SC, 2 Km (1.2 miles) SM
120 km (74.6 miles)
SC, 1000Base-LX 1310 nm
SFBRM1335-110 DMI
Continued on next page
112
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: FBRM/BFFG Part Numbers
Transition Networks
FBRM fiber-to-fiber part numbers, continued
Single-fiber
models
The models shown in Table 18 are single-fiber models and must be installed in pairs.
Table 18: FBRM13xx-1xx Single Fiber Model Pairs
Port 1: Fiber
100Base-FX
Port 2: Fiber
1000Base-SX/LX
Part Number
CFBRM1329-100*
100Base-FX 1300 nm
SC, 1000Base-LX BX-U
CFBRM1329-110* DMI MM SC, 2 Km (1.2 miles) 1310 nm TX/1490 nm RX
SFBRM1329-100*
SFBRM1329-110* DMI
CFBRM1329-101*
SM
20km (12.4 miles)
SC, 1000Base-LX BX-D
100Base-FX 1300 nm
CFBRM1329-111* DMI MM SC, 2 Km (1.2 miles) 1490nm TX/1310 nm RX
SFBRM1329-101*
SM
SFBRM1329-111* DMI
20 km (12.4 miles)
CFBRM1329-102**
R100Base-FX 1300 nm
SC, 100Base-LX BX-U
CFBRM1329-112** DMI MM SC, 2 Km (1.2 miles) 1310 nm TX/1490 nm RX
SFBRM1329-102**
SFBRM1329-112** DIM
CFBRM1329-103**
SM
40 km (24.9 miles)
SC, 100Base-LX BX-D
100Base-FX 1300 nm
CFBRM1329-113** DMI MM SC, 2 Km (1.2 miles) 1490 nm TX/1310 nm RX
SFBRM1329-103**
SM
SFBRM1329-113** DMI
40 km (24.9 miles)
BX-D (down stream) BX-U (up stream)
*FBRM-100 and -101, -110 and -111 Device pairs require installation in the same
network, where one is the local Device and the other its remote peer.
**FBRM-102 and -103, -112 and -113 Device pairs require installation in the same
network, where one is the local Device and the other its remote peer.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix A: FBRM/BFFG Part Numbers
FBRM fiber-to-fiber part numbers, continued
SFP models
The models shown in Table 19 use SFP (small form factor pluggable) Devices sold
separately from Transition Networks.
Table 19: FBRM1340-1xx (SFP Models)
Part Number
CFBRM1340-100
SFBRM1340-100
Port 1: Copper 10/100Base-T Port 2: Empty
RJ-45 100m (328ft) Empty SFP slot
Note: The distances for Port 1 listed in Table 19 are typical maximum distances;
the physical characteristics of the network dictate actual distances.
Note: Compatible SFP transceiver Devices for the FBRM1040-1xx Devices are
available from Transition Networks (sold separately). See the TN-SFP-xxx
series SFP manual # 33308 at www.transiton.com for available options.
114
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: FBRM/BFFG Part Numbers
Transition Networks
BFFG copper-to-fiber part numbers
Standard
models
The models shown in Table 20 perform as described in this manual.
Table 20: xBFFGxx-1xx Model Numbers
Port 1: Copper
Part Number
Port 2: Fiber
1000Base-X
Empty Slot
10/100/1000Base-T
CBFFG1040-100
SBFFG1040-100
RJ-45
100m (328ft)
Note: The distances for Port 1 listed in Table 20 are typical maximum distances;
the physical characteristics of the network dictate actual distances.
Note: Compatible SFP transceiver Devices for the FBRM1040-1xx Devices are
available from Transition Networks (sold separately). See the TN-SFP-xxx
series SFP manual # 33308 at www.transiton.com for available options.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix A: FBRM/BFFG Part Numbers
BFFG fiber-to-fiber part numbers
Gbit models
The models shown in Table 21 perform as described in this manual.
Table 21: BFFG13xx-1xx Gbit Models
Part Number
Port 1: Fiber
1000Base-SX
Port 2: Fiber
1000Base-SX/LX
SC, 1000Base-SX 850 nm
MM
CBFFG1313-100
SC, 1000Base-SX 850 nm
CBFFG1313-110 DMI MM
SBFFG1313-100
220/550 m (722/1,804 ft)*
220/550 m (722/1,804 ft)
SBFFG1313-110 DMI
CBFFG1314-100
CBFFG1314-110 DMI MM
SC, 1000Base-SX 850 nm
SC, 1000Base-LX 1310 nm
SM
SBFFG1314-100
220/550 m (722/1,804 ft) *
10 Km (6.2 miles)
SBFFG1314-110 DMI
CBFFG1315-100
CBFFG1315-110 DMI MM
SC, 1000Base-SX 850 nm
SC, 1000Base-LX 1310 nm
SM
SBFFG1315-100
220/550 m (722/1,804 ft) *
25 km (15.5 miles)
SBFFG1315-110 DMI
CBFFG1317-100
CBFFG1317-110 DMI MM
SC, 1000Base-SX 850 nm
SC, 1000Base-LX 1310 nm
SM
SBFFG1317-100
220/550 m (722/1,804 ft) *
65 km (40.3 miles)
SBFFG1317-110 DMI
CBFFG1335-100
SBFFG1335-110 DMI MM
SC, 1000Base-SX 850 nm
SC, 1000Base-LX 1310 nm
SM
CBFFG1335-100
220/550 m (722/1,804 ft) *
120 km (74.6 miles)
SBFFG1335-110 DMI
*220 (722 ft):
62.5/125µ fiber
50/125µ fiber
*550 m (1,804 ft):
Continued on next page
116
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: FBRM/BFFG Part Numbers
Transition Networks
BFFG fiber-to-fiber part numbers, continued
Single-fiber
models
The models shown in Table 22 are single-fiber models and must be installed in pairs.
Table 22: BFFG13xx-1xx Single Fiber Model Pairs
Port 1: Fiber
1000Base-SX
Port 2: Fiber
1000Base-SX/LX
Part Number
CBFFG1329-100**
SC, 1000Base-SX 850 nm SC, 1000Base-LX BX-U
CBFFG1329-110** DMI MM
1310 nm TX/1490 nm RX
SBFFG1329-100**
SBFFG1329-110** DMI
CBFFG1329-101**
220/550 m (722/1,804 ft)* SM
20km (12.4 miles)
SC, 1000Base-SX 850 nm SC, 1000Base-LX BX-D
CBFFG1329-111** DMI MM
1490 nm TX/1310 nm RX
SBFFG1329-101**
220/550 m (722/1,804 ft)* SM
SBFFG1329-111** DMI
20 km (12.4 miles)
CBFFG1329-102***
SC, 1000Base-SX 850 nm SC, 100Base-LX BX-U
CBFFG1329-112*** DMI MM
1310 nmTX/1490 nm RX
SBFFG1329-102***
SBFFG1329-112*** DIM
CBFFG1329-103***
220/550 m (722/1,804 ft)* SM
40 km (24.9 miles)
SC, 1000Base-SX 850 nm SC, 100Base-LX BX-D
CBFFG1329-113*** DMI MM
1490 nm TX/1310 nm RX
SBFFG1329-103***
220/550 m (722/1,804 ft)* SM
SBFFG1329-113*** DMI
40 km (24.9 miles)
BX-D (down stream) BX-U (up stream)
*220 (722 ft):
62.5/125µ fiber
50/125µ fiber
*550 m (1,804 ft):
**BFFG-100 and -101, -110 and -111 Device pairs require installation in the same
network, where one is the local Device and the other its remote peer.
***BFFG-102 and -103, -112 and -113 Device pairs require installation in the same
network, where one is the local Device and the other its remote peer.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix A: FBRM/BFFG Part Numbers
BFFG fiber-to-fiber part numbers, continued
SFP models
The models shown in Table 23 use SFP (small form factor pluggable) Devices sold
separately from Transition Networks.
Table 23: BFFG1340-1xx (SFP Models)
Port 1: Fiber
1000Base-SX
Part Number
Port 2: Empty
CBFFG1340-100
SBFFG1340-100
SC, 1000Base-SX 850 nm MM Empty SFP slot*
220/500 m (728/1,640 ft)
*Compatible SFP transceiver Devices for the BFFG1340-1xx Devices are available
from Transition Networks (sold separately). See the TN-SFP-xxx series SFP manual
118
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: FBRM/BFFG Part Numbers
Transition Networks
Intentionally Blank
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix B:
FBRM/BFFG Technical Specification
Specifications, notices, and warnings
For use with Transition Networks’ Models FBRM and BFFG or equivalent.
Parameter
IEEE Standards
Description
IEEE 802.3-2000
IEEE 802.3ah-2004 clause 57, 58
IEEE 802.1q-2003
IEEE 802.1x-2004
IEEE 802.1D
IEEE 802.1P
RFC compliance
See Appendix D
Regulatory Compliance for Emission EN55022 Class A
Regulatory Compliance for Immunity EN55024
Safety Compliance
Unit: CE Mark
Wall-Mount Power Supply: UL Approved,
UL60950, and CSA Certified
4 watts
Power Consumption
MTBF* CFBRM & CBFFG models 141,526 MIL217F2 hours
518,418 Bellcore hours
SFBRM & SBFFG models 39,895 MIL217F2 hours
106,056 Bellcore hours
Power Source
7.5 to 15.9 VDC – Wall-mount AC Adapter
or Point System Backplane (provided)
Max Frame Size
Size (width x height x depth)
Weight
Operating Temperature
Storage Temperature
Altitude
1628 bytes
3.3 x 1 x 4.75 in (83.8 x 25.4 x 120.65 mm)
Standalone: 4oz (113.4 grams)
0 to 45º C (32 to 113º F)
-25 to 65º C (-13 to 149ºF)
0-10,000 feet
Operating Humidity
5% to 95% (non-condensing)
MTBF criteria
*MTBF is estimated using the predictability method. This method is based on MIL-
104°F at 40°C ambient temperature, typical enclosure heat rise of 10°C, and nominal
operating conditions and parameters. Installation and configuration specific MTBF
estimates are available upon request: Contact Technical Support.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: FBRM/BFFG Technical Specifications
Transition Networks
Specifications, notices, and warnings, continued
Notices
• The information in this user’s guide is subject to change. For the most up-to-date
information on the FBRM/BFFG Devices, see the user’s guide on-line at:
• Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
• IMPORTANT Copper based media ports: e.g., Twisted Pair (TP) Ethernet, USB,
RS232, RS422, RS485, DS1, DS3, Video Coax, etc., are intended to be connected
to intra-building (inside plant) link segments that are not subject to lightening
transients or power faults.
CAUTION: Copper-based media ports, e.g., Twisted Pair (TP) Ethernet, USB,
RS232, RS422, RS485, DS1, DS3, Video Coax, etc., are NOT to be connected to
inter-building (outside plant) link segments that are subject to lightening transients or
power faults. Failure to observe this caution could result in damage to equipment.
Warnings
WARNING: Visible and invisible laser radiation when open: DO NOT stare into the
beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
WARNING: If the media Device is an IEEE802.3-2005 Powered Device (PD)
capable of receiving power via the Medium Dependent Interface (MDI) leads, the
power source, connector, and cabling attached to the barrel power connector must
meet the isolation requirement specified in IEEE802.3-2005. Failure to observe this
warning could result in an electrical shock.
IMPORTANT
The xFBRM/xBFFG Device product family is not compatible with the CPSMM-200
and CPSMM-210 management modules when they are used in a cascaded
application. The xFBRM/xBFFG can be installed in the “master” chassis with the
CPSMM-200, but they can not be installed in a cascaded chassis using the CPSMM-
210.
Alternatively, the xFBRM/xBFFG can be used with the CPSMM-120 base
management module, which does not support cascading of the chassis.
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix C:
Device Commands & Descriptions
Command
arp
Descriptions
Displays the arp cache.
clear counter
Clears counters on all ports or on a specific port. Usage:
clearcounter [port=<portno>]
cls
Clears the screen.
exit
Exits the CLI/Telnet session.
factory defaults
Resets the Device to factory default settings—all current
configurations will be erased.
help or ?
Help or ?:
Displays the available commands.
help <cmd >: Displays the command usage in detail.
Used to configure port parameters. The port number for
the configured port must be specified. Valid port
numbers start at “1.”
ifconfig port=<portno>
Usage: ifconfig port=<portno>
[adminstate=<enable|disable]
[autoneg=<enable|disable>]
[duplex=<full|half>]
[speed=<10|100|1000>]
[portstring=<"value">(max=64)]
[iptraffic=<enable|disable>]
The configurable parameters are as follows:
adminstate: The port can be disabled or enabled.
autoneg:
Enable/disable Auto-Negotiation on this
port.
duplex:
When Auto-Negotiation is disabled,
Duplex Mode of the port can be set to
full/half duplex.
speed:
The port speed can be set to 10/100 Mbps
when Auto-Negotiation is disabled.
A unique name can be assigned to each
port.
The IP traffic can be enabled/disabled on
each port individually.
portstring:
iptraffic:
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Device Commands & Definitions
Transition Networks
Command
Description
ifoam port=<portno>
OAM configuration for the specified port.
Usage: ifoam port=<portno>
[oam=enable|disable]
[oammode=active|passive]
[oamrmtloop=enable|disable]
OAM:
OAM can be enabled/disabled.
Oammode:
OAM Mode can be set to Passive/Active
Mode.
Oamrmtloop: OAM loopback can be enabled/disable
on the remote Device peer.
netstat
ping
Displays all active and passive sockets.
Pings the host to check if it is reachable using ICMP
requests.
ps
Displays the system processes.
Saves the current configuration and reboots the system.
Saves the current configuration to non-volatile memory.
Sets network settings and system configuration.
Usage: set
reboot
save
set
[dhcp=<enable|disable>]
[ip=nn.nn.nn.nn]
[netmask=nn.nn.nn.nn]
[gateway=nn.nn.nn.nn]
[trapmgr=nn.nn.nn.nn]
[community=<"value">(max=64)]
[groupstring=<"value">(max=64)]
[radius=<enable|disable)]
[radiusip=nn.nn.nn.nn]
[radiussercret=<"value">(max=64)]
[username=<"value">(max=64)]
[password=<"value">(max=64)]
[usb=<enable|disable>]
[l3capability=<enable|disable)]
[snmpaccess=<enable|disable)]
[tftpserver=nn.nn.nn.nn]
[tftpfile=<"value">(max=64)]
[mgmtvlan=<vlanid>(2-4096)
set autoupg
Enable/disable auto upgrade.
When enabled, automatically upgrades the firmware.
Usage: set autoupg=<enable|disable>. This locks/unlocks
firmware upgrades from an active OAM Device peer.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix C: Device Commands & Definitions
Command
Description
set community
Sets SNMP community name.
Usage: set community=<name>
set dhcp
Enables/disables DHCP at boot time. In case DHCP
failed during initialization, retry using the “restart”
option.
Usage: set dhcp=<enable|disable|restart>
set downloadcfg
Download the system configuration from a TFTP
Server.
Usage: Usage: set downloadcfg=<"filename">
[l3access=<enable|disable>] [ipsetting=<default|nochange>
Note: The ‘l3access’ and ‘ipsetting’ are options to turnOFF
IP access once the upgrade is done, and to change
the IP address, subnet and gateway to factory
defaults.
set forceupg
Enable/disable forcing a firmware upgrade of the peer
on specified port, automatically.
Usage: set forceupg port=<portno>
set gateway
Sets gateway address.
Usage: set gateway=nn.nn.nn.nn
set groupstring
set uploadcfg
Sets group string for the system.
Usage: set groupstring=<"name">(max=64)
Sets uploading the system configuration to a TFTP
Server.
Usage: Usage: set uploadcfg=<"filename">
set downloadcfg
Sets Downloading the system configuration from a
TFTP Server.
Usage: Usage: set
set ip
Sets IP address.
Usage: set ip=nn.nn.nn.nn
set l3capability
set mgmtvlan
set niecho
Enables/disables all layer-3 traffic.
Usage: set l3capability=<enable|disable>
Sets management VLAN ID for management traffic.
Usage: set mgmtvlan=<vlanid>
Sets the number of echo frames to be sent, and start the
non-intrusive echo frame generation on the interface.
Usage: set niecho port=<portno> count=<1-100>
set autoupg
set forceupg
Enable/disable auto upgrade. When enabled, Auto
firmware upgrade be done.
Usage: set autoupg=<enable|disable>
Enable/disable Forcing Auto firmware upgrade on Peer
on specified port
Usage: set forceupg port=<portno>
Continued on next page
124
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Device Commands & Definitions
Transition Networks
Command
Description
set slpt
Enable/disable Selective Link pass through.
Usage: set slpt=<enable|disable>
set tlpt
Enable/disable Transparent Link pass through.
Usage: set tlpt=<enable|disable>
set 12cp
Sets the L2CP protocol diposition per port if 'port' is
given, else sets all ports forwarding rule for that
protocol.
Usage: set l2cp="<stp|slow|dot1x|elmi|lldp|bmgmt|garp|other>"
port=<portno> act="<forward|discard>"
set fiberredund
Set fiberrevert
set netmask
Sets Enable/disable Fiber Redundancy.
Usage: set fiberredund=<enable|disable>
Enable/disable Fiber Redundancy revert.
Usage: set fiberrevert=<enable|disable>
Sets subnet mask.
Usage: set netmask=nn.nn.nn.nn
set orceupg
Enable/disable forcing auto firmware upgrade on the
peer of a specified port.
Usage: set forceupg port=<portno>
set password
set radius
Sets password for CLI access through serial port/telnet.
This is used when RADIUS is disabled.
Usage: set password=<"value">(max=64)
Enables/disables RADIUS authentication. RADIUS is
disabled by default.
Usage: set radius=<enable|disable>
Sets RADIUS server IP.
set radiusip
Usage: set radiusip=nn.nn.nn.nn
set radiussecret
set snmpaccess
set tftpfile
Sets RADIUS secret shared with the RADIUS server.
Usage: set radiussecret=<"value">(max=64)
Enables/disables all SNMP access.
Usage: set snmpaccess=<enable|disable>
Sets tftp filename to be downloaded using upgrade with
TFTP.
Usage: set tftpfile=<"value">(max=64)
Sets TFTP server IP address to be used for upgrading
via TFTP.
set tftpserver
Usage: set tftpserver=nn.nn.nn.nn
Sets trap manager address.
Usage: set trapmgr nn.nn.nn.nn
Uploads the system configuration to a TFTP Server.
Usage: set uploadcfg=<"filename">
Disables the USB port. This disables access through the
USB port. It can be enabled using IP-based or Point
System management.
set trapmgr
set uploadcfg
set usb
Usage: set usb=disable
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix C: Device Commands & Definitions
Command
Description
set username
Sets username for CLI access through serial port/telnet.
This username is used when RADIUS is disabled.
Usage: set username=<"value">(max=64)
show
Displays all the current configurations at the system
level, including installed firmware revisions, network
configurations, system uptime, etc.
Shows current version of the firmware build
information.
show version
Show redundancy
show ifcabletest
Shows fiber redundancy settings.
Performs cable tests and displays the cable status for all
or a specified port.
Usage: show ifcabletest port=<all | port no>
show ifconfig
show ifoam
Displays port configurations, including speed, duplex,
and IP access for a specified port, or all ports.
Usage: show ifconfig [port=<all | port no>]
Displays OAM configuration and status for all or a
specified port.
Usage: show ifoam [port=<all | port no>]
show ifrmonstats
show ifstats
Displays RMON statistics for all or a specified port.
Usage: show ifrmonstats [port=<all | port no>]
Displays port statistics for all or a specified port.
Usage: show ifstats [port=<all | port no>]
show oamloopback
Displays OAM Loopback status for all or a specified
port.
Usage: show oamloopback [port=<all | port no>]
show niecho
Displays Non-intrusive echo generation status for all or
specified port
Usage: show niecho [port=<all | port no>]
show 12cp is (L2cp)
show oampeer
Displays L2CP disposition for all or specified port
Usage: show l2cp [port=<all | port no>]
Displays OAM peer information for all or a specified
port.
Usage: show oamloopback [port=<all | port no>]
show oamstatistics
Displays OAM PDU statistics for all or a specified port.
Usage: show oamstatistics [port=<all | port no>]
Continued on next page
126
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Device Commands & Definitions
Transition Networks
Command
Description
snmpget
SNMP GET on the OID is performed try "snmpget
help" for more information.
Usage: snmpget [oid=1.2.3.4 | variable=<leaf var | tableEntry.x.y>]
• If the ‘oid’ option is used, the indices should be
present for table variables and '0' for leaf variables.
• If the 'variable' option is used, the leaf variables can
be named as is, the table variables have the
following format <tableentry>.index1.index2
Ex: snmpget variable=sysUpTime
snmpget variable=ifEntry.<col>.<ifNumber>
snmpgetn
SNMP get-next on the OID is performed if there is no
OID specified. It uses OID from the last SNMP query,
try "snmpgetn help" for more information.
Usage: snmpgetn [oid=1.2.3.4 | variable=<leaf var|tableEntry.x.y>]
• If the 'oid' option is used, the indices should be
present for table variables and '0' for leaf variables.
• If the 'variable' option is used, the leaf variables can
be named as is, the table variables have the
following format <tableentry>.index1.index2.
Ex: snmpgetn variable=sysContact
snmpgetn variable=ifEntry ifEntry.<col>.<ifNumber>
snmpset
SNMP SET on the OID is performed with the value, try
"snmpset help" for more information.
Usage: snmpset oid=<x.y.z> type=<STR | IP | INT>
value=<value>
• Strings must be enclosed in quotes (“”). If the ‘oid’
option is used, the indices should be present for
table variables and ‘0’ for leaf variables.
• If the 'variable' option is used, the leaf variables can
be named as is, the table variables have the
following format <tableentry>.index1.index2
Ex: snmpset variable=sysContact type=STR
value="[email protected]"
snmpset variable=ifEntry.2.<ifNumber>
type=STR value="Interface 1."
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix C: Device Commands & Definitions
Command
Description
snmpwalk
SNMP walk of the entire MIB tree if no options are
specified or from OID from the last query if 'continue' is
specified.
Usage: snmpwalk <continue>
sys
The system group variables of MIB-II can be configured
using the ‘sys’ command. The system contact, name,
and location can be set.
Usage: sys
[contact=<"value">(max=64)]
[name=<"value">(max=64)]
[location=<"value">(max=64)]
tftpupgrade
Upgrades the firmware running on the Device using
TFTP protocol. The tftp server IP and tftp filename
should be configured using the “set” command, or can
be given as arguments to this command.
Usage: tftpupgrade erver=nn.nn.nn.nn filename=<"filename">
xmodemupgrade
Upgrades the firmware running on the Device, using
XModem protocol. The command invokes the
bootloader and start an XModem transfer to upgrade the
firmware.
128
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix D:
IP-Based and Chassis Management Parameters
IP- and chassis- The chassis Device version of the Devices plugs into a Point System chassis to
based
management
provide management through the I2C interface: SNMP and web-based management
through the MMU. SNMP management is based on the Transition Networks
enterprise MIBs. The chassis-based management (via the MMU) provides a subset of
the IP-based management via ports. Tables 26, 27, and 28 present IP- and chassis-
based configuration management parameters.
Note: The 9 mark means available; a blank cell means not available.
Table 24: System Configuration Parameters
Parameter
BootLoader
Version
IP based Chassis Description
9
9
The currently installed version of the
Bootloader.
9
9
9
9
Config Match
Default Gateway
Configuration management match.
The gateway in a network that will be
used to access another network if a
gateway is not specified for use.
DHCP (Dynamic Host Configuration
Protocol) Enable/disable DHCP to obtain
IP, subnet mask, and gateway data upon
reboot.
9
9
DHCP
9
9
Firmware Version
The currently installed version of the
firmware.
9
9
9
9
9
9
IP Address
IP Traffic Access
MAC Address
IP address of the Device.
Enable/disable IP Traffic to the Device.
The MAC address is a unique identifier
is a number that acts like the name for a
particular network adapter.
9
9
Management
VLAN ID
Thru CLI
only
When 802.1q is enabled, the administrator
can configure VLAN IDs used for all
management traffic to and from the
Device via the CLI or through the chassis
management agent.
9
9
Marketing
Revision
RADIUS
Enable/disable RADIUS authentication.
When enabled, the user is authenticated
during login at the CLI or web interface.
Authentication
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix D: IP-Based and Chassis Management Parameters
Table 26: System Configuration Parameters (continued)
Parameter
IP based Chassis Description
9
9
RADIUS Retry
RADIUS Secret
Retries after a network failure.
The shared secret between this Device
and the RADIUS server.
9
9
RADIUS Server
Address
The IP address of the RADIUS server is
used to get user information during
authentication.
Timeout for each attempt to contact the
server.
RADIUS timeout
9
9
9
9
Serial Access
Serial Number
Enable/disable USB port access.
Serial number of the chassis that the
Device is installed.
9
9
9
9
9
9
SNMP Access
SNMP Trap Mgr
Subnet Mask
Enable/disable SNMP management.
SNMP trap manager IP address.
Determines where the network number in
an IP address ends and the node number
in an IP address begins.
9
9
9
9
9
9
9
9
TFTP Filename
The filename used to upgrade, using
TFTP (local Device only).
TFTP server IP address to use for
firmware upgrades (local Device only).
Initiates TFTP firmware upgrades (local
Device only).
Enable/disable TLPT. TLPT causes the
loss of link on one side of a Device to be
passed through to the other side so that
the upstream Device can see fault
conditions that would otherwise be
hidden by Devices.
TFTP Server
Address
TFTP upgrade
Transparent Link
Pass-Through
Note: TLPT requires Auto-Negotiation
to be enabled on the twisted pair
interface.
Continued on next page
130
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: IP-Based and Chassis Management Parameters
Transition Networks
Table 25: Media Device Parameters
Parameter
IP based Chassis Description
9
Aging Time
(Forwarding DB)
Factory Defaults
The aging time (in seconds) for entries in
the forwarding database of the switch.
This erases all configuration data and sets
the Device to factory default settings.
Flushes all forwarding database entries.
Flushes all VLAN database entries.
This determines what frame types are
accounted for in the port counters. The
choices are “count only RX frames” or
TX frames or both.
9
9
9
9
9
Flush FDB
Flush VLAN DB
Histogram Mode
9
9
IEEE Priority class
'n' [0-7]
IEEE 802.1p priority mapping. The value
in this field is used as the priority of the
frame if it has the tag ‘n.’
IP priority remapping. The value in this
field is used as the priority of the frame if
its IP TOS bits have a traffic class value
between 0x00 and 0xE0, with 1 --> 0x00,
2 --> 0x04,...64 --> 0xE0.
IP Traffic class 'n'
[1-64]
9
9
Reset Counters
Resets all port counters to zero.
Table 26: Port Configuration Parameters
Parameter
IP based Chassis Description
9
9
Admin Status
The administrative status of the interface
should be enabled for normal operation.
When the admin state is disabled, the port
goes into listening mode, the link will be
UP, but the interface does not forward
frames.
9
9
9
9
9
9
9
9
9
9
Advt 10 Full
Duplex
Advt 10 Half
Duplex
Advt 100 Full
Duplex
Advt 100 Half
Duplex
Enable/disable advertising full duplex
and 10Mbps capability on this port.
Enable/disable advertising half duplex
and 10Mbps capability on this port.
Enable/disable advertising full duplex
and 100Mbps capability on this port.
Enable/disable advertising half duplex
and 100Mbps capability on this port.
Enable/disable advertising Pause
capability on the interface.
Advt Pause
capability
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix D: IP-Based and Chassis Management Parameters
Table 28: Port Configuration Parameters (continued)
Parameter
IP based Chassis Description
9
9
Autocross
When enabled, detects and configures the
twisted pair port on the Device to the
correct MDI or MDI-X configuration
automatically.
9
9
9
Auto-Negotiation
Allows Devices to configure themselves
automatically to achieve the best possible
mode of operation over a link.
9
9
Connector Type
DA Priority
Override
When enabled, the DA (destination
address) of the frame is used to get a hit
on the address database with an entry
matching the DA when priority override
is enabled. The priority specified in the
entry is the new priority of the frame. The
DA override has a higher priority than the
default priority of the frame, IP TOS,
IEEE Priority tags, VTU override, and
SA override. Normal frame priority
processing occurs when disabled.
When enabled, multicast frames with
unknown destination addresses are
allowed to ‘egress’ this port if VLAN is
enabled. The VLAN setting also allows
this port to ‘egress.’
9
Default Forward
9
9
Default Priority
The default priority of the frames
entering the port when no other priorities
are assigned and enabled.
When IEEE 802.1q is enabled, the default
VID is used as the IEEE tagged VLAN
ID to un-tag or priority tag frames when
they ‘egress of this port.
Default VLAN ID
9
Description String
Group string for this port with the
maximum length of 64 characters.
Continued on next page
132
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: IP-Based and Chassis Management Parameters
Transition Networks
Table 28: Port Configuration Parameters (continued)
Parameter
IP based Chassis Description
9
9
9
Discard Tagged
When enabled, all non-management
frames processed as tagged are discarded.
If double tagging is enabled, then this
check is performed after Ingress double
tag removal. Frames with priority and
VLAN of “0” are considered tagged.
When enabled, all non-management
frames processed as untagged are
discarded. If double tagging is enabled,
then this check is performed after Ingress
double tag removal. Frames with priority
and VLAN of “0” are considered tagged.
When enabled, all non-management
frames processed as untagged are
Discard Untagged
Discard Untagged
discarded. If double tagging is enabled,
then this check is performed after
‘ingress’ double tag removal. Frames
with priority and VLAN of “0” are
considered tagged.
9
Double Tagging
This enables ‘ingress’ double-tagging. It
is a way to isolate one VLAN from
another VLAN hierarchically. When
enabled, also enables ‘egress’ double
tagging. In this mode, the Ingress port
removes the first IEEE 802.3ac tag that
appears after the source address. If a
frame is untagged, it is not modified. If it
is single tagged it is removed; if it is
double tagged, the first tag is removed.
The Duplex Modeof the port (half/full).
When enabled, all ‘egress’ frames that
come from this port are sent to the
‘egress’ monitor destination port
9
9
9
Duplex
Egress Monitor
Port
(sfbrm100SwEgressMonPort).
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix D: IP-Based and Chassis Management Parameters
Table 28: Port Configuration Parameters (continued)
Parameter
IP based Chassis Description
9
9
Egress Rate
Controls the effective port transmission
rates. The rate limit is provided as a list
of pre-defined values:
. noLimit(1)
. rate64K(2)
. rate96K(3)
. rate128K(4)
. rate160K(5)
. rate192K(6)
. rate224K(7)
. rate256K(8)
. rate320K(9)
. rate384K(10)
. rate512K(11)
. rate768K(12)
. rate1M(13)
. rate1_2M(14)
. rate1_5M(15)
. rate2M(16)
. rate3M(17)
. rate4M(18)
. rate5M(19)
. rate8M(20)
. rate10M(21)
. rate20M(22)
. rate30M(23)
. rate40M(24)
. rate60M(25)
. rate80M(26)
9
9
9
Far-End Fault
Indication
Force Def VLAN
ID
Far-End Fault (FEF) is a troubleshooting
feature on the 100Base-TX port
When enabled, forces all ‘ingress’ frames
with IEEE 802.3ac tags to have
replacement VLAN IDs in the frame with
the port's default VID. This is valid only
if IEEE 802.1q is enabled.
Continued on next page
134
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: IP-Based and Chassis Management Parameters
Transition Networks
Table 28: Port Configuration Parameters (continued)
Parameter
IP based Chassis Description
9
Forward Unknown
When enabled, unicast frames with
unknown destination addresses are
allowed to ‘egress’ this port if VLAN is
enabled. The VLAN setting also allows
this port to ‘egress.’
9
IEEE Priority class
‘n’ [0-7]
The priority remapping for frames that
‘ingress’ this port. The IEEE tagged
frames with priority ‘n’ get this new
remapped priority inside the switch; also
if it egresses this port as tagged, the
priority is set in the tag.
9
9
9
9
IGMP Snoop
This enables IGMP frame forwarding to
the CPU. IGMP is not supported in the
present release.
This corresponds to the EFM OAM MIB.
It decides whether the OAM loopback on
this port should be ignored.
This is related to the Port Lock. Enabling
this parameter will stop source-address
violations caused by Port Lock.
This determines what kinds of frames are
limited and counted against ‘ingress’
limiting. Frames not limited by this
setting are not counted against the limit.
When enabled, all ‘ingress’ frames are
sent to the ‘ingress’ monitor destination
port (sfbrm100SwIngressMonPort).
When disabled, all IP traffic through this
port to the CPU is restricted.
9
9
Ignore Loopback
Ignore Wrong Data
Ingress Limit mode
9
Ingress Monitor
Port
9
9
9
9
IP Traffic
Link Partner
Autoneg ability
Link Partner Pause
ability
Speed and duplex capabilities of the Link
Partner.
Pause frame capabilities of the Link
Partner.
9
Link Status
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix D: IP-Based and Chassis Management Parameters
Table 28: Port Configuration Parameters (continued)
Parameter
OAM Mode
Control
IP based Chassis Description
9
9
This determines how the OAM Modefor
ports is configured (manual/auto):
• In auto mode, the port defaults to active
if in a chassis; passive if a standalone.
• In manual mode, the user can choose
the OAM mode, using the EFM HUB
MIB under the TN private MIB tree.
9
9
9
9
OAM State
Port Index
Port Lock
Enable/disable IEEE 802.1ah OAM
management on this port.
The index of the port in
sfbrm100PortTable.
IEEE 802.1x MAC authentication. All
non-management frames received on this
port are discarded if the source address is
not in the learned-address database; this
could cause continuous MAC address
violation. To prevent this, an entry with
all port vectors as ‘0’ can be added to the
address database. This disables learning
new source addresses.
Continued on next page
136
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: IP-Based and Chassis Management Parameters
Transition Networks
Table 28: Port Configuration Parameters (continued)
Parameter
IP based Chassis Description
9
9
Pri0 Ingress Rate
Rate limit for Priority “0” frames. The
rate limit is provided as a list of pre-
defined values:
. noLimit(1)
. rate64K(2)
. rate96K(3)
. rate128K(4)
. rate160K(5)
. rate192K(6)
. rate224K(7)
. rate256K(8)
. rate320K(9)
. rate384K(10)
. rate512K(11)
. rate768K(12)
. rate1M(13)
. rate1_2M(14)
. rate1_5M(15)
. rate2M(16)
. rate3M(17)
. rate4M(18)
. rate5M(19)
. rate8M(20)
. rate10M(21)
. rate20M(22)
. rate30M(23)
. rate40M(24)
. rate60M(25)
. rate80M(26)
9
9
9
9
Pri1 Ingress Rate
Control
Rate limit for Priority “1” frames to be
the same or twice that of the Priority “0”
frames.
Rate limit for Priority “2” frames to be
the same or twice that of the Priority “1”
frames.
Pri2 Ingress Rate
Control
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix D: IP-Based and Chassis Management Parameters
Table 28: Port Configuration Parameters (continued)
Parameter
Pri3 Ingress Rate
Control
IP based Chassis Description
9
9
Rate limit for Priority “3” frames to be
the same or twice that of the Priority “2”
frames.
9
9
9
9
Remote Loopback
Enable/disable OAM loopback on the
remote.
Resets the port counters.
9
Reset Port
Counters
SA Priority
Override
When enabled, the source address of the
frame is checked against the address
database entry with the matching source
address with priority override enabled.
When there is a match, the fame priority
is the one found in the entry. The source
address priority override has a higher
priority than the default frame priority, IP
TC, IEEE priorities, and the VLAN
priority override values. Normal frame
priority processing occurs when disabled.
The speed in Mbps for this interface. It is
the resolved speed when Auto-
9
9
9
Speed
Negotiation is enabled or the manually
set the value when Auto-Negotiation is
disabled.
Use Both Traffic
class
When a frame has an IEEE 802.ac tag
and an IP TOS, then this depends on
which priority is chosen, IP TOS or IEEE
tag when both sfbrm100PortUseIPTC and
sfbrm100PortUseTagTC are enabled.
This enables the IP Traffic class priority
if present. If disabled, the TOS bits are
ignored.
9
9
Use IP Traffic
class
Use Tag Traffic
class
This enables the IEEE 802.1p priority if
the frame is IEEE 802.3ac tagged, or else
it is ignored even if the tag is present.
Continued on next page
138
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: IP-Based and Chassis Management Parameters
Transition Networks
Table 28: Port Configuration Parameters (continued)
Parameter
IP based Chassis Description
9
9
Virtual Cable Test
The virtual cable test determines the
quality of the cable, connectors, and
terminations. Problems such as opens,
shorts, and cable impendence mismatch
can be diagnosed with this test.
9
VLAN Status
802.1q VLAN can be disabled or enabled
along with setting the following options:
Secure: The VLAN ID must be
contained in the VLAN database (Db)
and the ‘ingress’ port must be a member
of the VLAN or else it will be discarded.
Check: The VLAN ID must be contained
in the VLAN Db or the frame will be
discarded.
Fallback: The frames are not discarded if
their VLAN ID is not in the VLAN Db.
In all the above cases, the frames are
allowed to exit ports that are members of
the frame's VLAN, including the source
port's VLAN table
(sfbrm100PortBasedVLANTbl).
Also, frames that do not have a VLAN ID
in the Db can exit only ports in the
VLAN table.
Disabled: 802.1q is disabled.
9
9
VLAN Table
This is a bitmap that restricts the output
ports that this input port can send frames
to. To send frames through port ‘2,’ bit
‘2’ of this value must be set to ‘1.’
When enabled, frames that have a source
address in the forwarding database are
allowed to bypass Port-based VLAN,
IEEE 802.1q VLAN and trunk masking.
VLAN Tunnel
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix D: IP-Based and Chassis Management Parameters
Table 28: Port Configuration Parameters (continued)
Parameter
VTU Priority
Override
IP based Chassis Description
9
When enabled, the port checks the frames
for VLAN IDs that have the VTU Priority
override bit set in the VLAN database. It
then replaces the priority of the frames
with the priority specified in the VLAN
entry, which has a higher priority than the
default of the frame and IP/IEEE
priorities. Normal frame priority
processing occurs when disabled.
Static MAC
and VLAN
tables
The static MAC and VLAN tables are supported only through IP-based management
and not through chassis-based management. The chassis supports RMON MIB
counters only on ports. The IP-based management supports public MIB counters
such as RMON, IFmib. Ether-like MIB, EFM OAM HUB MIB, and port counters
directly from the switch.
Note: The MIBs used by the chassis agent for the FBRM/BFFG Device and the
MIB used by IP-based management are different.
The chassis agent does not support the EFM hub MIB. If the remote Device
is OAM capable, but not a FBRM/BFFG Device from Transition Networks,
the EFM hub MIB will be queried for OAM status.
140
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix E:
Request for Comment (RFC) Compliance
RFC
The following is a list of RFC compliances.
compliance
[IP] Postel, J. "Internet Protocol DARPA Internet Program Protocol Specification",
RFC 791, USC Information Sciences Institute, September 1981.
[ICMP] J. Postel “Internet Control Message Protocol. RFC 792, September 1981.
[ARP] Plummer, David C., "An Ethernet Address Resolution Protocol", RFC 826.
Symbolics Inc., November 1982.
[UDP] Postel, J., "Use Datagram Protocol", RFC 768. USC Information Sciences
Institute, August 28, 1980.
[TCP] Postel, J., "Transmission Control Protocol DARPA Internet Program Protocol
Specification", RFC 793. USC Information Sciences Institute, September 1981.
[950] Mogul, J. and Postel, J., "Internet Standard Subnetting Procedure", RFC 950.
Network Working Group, August 1985.
[1122] Braden, R., "Requirements for Internet Hosts - Communications Layers", RFC
1122. Internet Engineering Task Force, October 1989.
[1123] Braden, R., "Requirements for Internet Hosts - Application and Support", RFC
1123. Internet Engineering Task Force, October 1989.
[DHCP] Droms, R., "Dynamic Host Configuration Protocol", RFC 2131. Bucknell
University, March 1997.
[HTTP] Fielding, R. et al, "Hypertext Transfer Protocol - HTTP/1.1", RFC 2616.
Network Working Group, June 1999.
[2617]Franks, J. et al, "HTTP Authentication: Basic and Digest Access
Authentication", RFC 2617. Network Working Group, June 1999.
[2396]Berners-Lee, T. et al, "Uniform Resource Identifiers (URI): Generic Syntax",
RFC 2396. MIT, August 1998.
[Telnet] Postel, J. and Reynolds, J., "Telnet Protocol Specification", RFC 854. USC
Information Sciences Institute, May 1983.
Continued on next page
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
141
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Appendix E: Request for Comment (RFC) Compliance
RFC compliance (continued)
[TFTP] Sollins, K., "The TFTP Protocol (Revision 2)", RFC 1350. MIT, July 1992.
[SMTP] Klensin, J. ed., "Simple Mail Transfer Protocol", RFC 2821. AT&T
Laboratories, April 2001.
[SNMP] Case, J. et al, "A Simple Network Management Protocol (SNMP)", RFC
1157.
[1213] Management Information Base for Network Management of TCP/IP-based
internets: MIB-II
[1493] Definitions of Managed Objects for Bridges. RFC 1493
[2674] Definitions of Managed Objects for Bridges with Traffic Classes, Multicast
Filtering and Virtual LAN Extensions. RFC 2674
[2819] Remote Network Monitoring Management Information Base. RFC 2819
[2863] The Interfaces Group MIB. K. McCloghrie, F. Kastenholz. June 2000, RFC
2863
[3635] Definitions of Managed Objects for the Ethernet-like Interface Types. RFC
3635
142
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Index
product.................................................................62
3-Port Switch..See Redundant SFBRM SFP, 3-Port
Switch
Fiber Optics
characteristics ......................................................92
xBFFG13xx Gbit.................................................99
xFBRM Gbit DMI ...............................................97
xFBRM10xx........................................................92
xFBRM13xx........................................................96
Auto Link Restore .................................................70
AutoCross
description ...........................................................62
Auto-Negotiation
description ...........................................................63
Bandwith Allocation
Firmware Upgrade
adimin intervention..............................................81
bootloader
description ...........................................................63
description .......................................................65
bootloader CLI.....................................................81
description ...........................................................62
failures.................................................................81
via OAM..............................................................81
via TFTP..............................................................80
via Xmodem ........................................................78
Bootloader
CLI access ...........................................................82
firmware upgrade.................................................81
help screen...........................................................82
Chassis
management module unit (MMU).........................4
COM Port
IEEE 802.3ah OAM
configuration........................................................29
properties.............................................................31
selecting...............................................................30
alternate loop back...............................................67
last gasp/OAM (operation administration and
maintenance) ...................................................66
last gasp/OAM dying gasp...................................66
organization specific PDUs .................................68
remote loop back .................................................67
Commands and Descriptions..............................124
Congestion Reduction
description ...........................................................64
In-Band Management..............................................2
Connecting
copper cables .......................................................21
power adapter (standalone model).......................22
Installing
chassis card..........................................................18
copper cables .......................................................20
standalone devices...............................................19
USB driver...........................................................25
Copper Cables
characteristics ......................................................91
Default
IP Configuration
factory IP config............................................32, 35
IP-based (web) password.....................................43
telnet password (directly to device).....................40
USB password (CLI access) ................................33
default............................................................32, 35
DHCP ..................................................................36
USB CLI..............................................................35
web-based............................................................46
Device Configurations Options
LED
chassis/standalone devices...................................77
status..............................................................74, 75
LEDs
DHCP
IP config ..............................................................36
IP config (set up web-based) ...............................45
setup (web-based)................................................48
BFFG...................................................................75
FBRM..................................................................74
FBRM/BFFG gbit status......................................76
Duplex
Link Pass Thru
full description.....................................................65
half desctiption ....................................................65
auto link restore ...................................................70
selective...............................................................70
transparent ...........................................................70
Far-End Fault
description ...........................................................64
Link Status Failure Indication
description ...........................................................68
Login
FBRM/BFFG
connection scenario (gbit models).......................14
supported features..................................................3
telnet ....................................................................40
Features
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
143
Download from Www.Somanuals.com. All Manuals Search And Download.
Transition Networks
Index
USB CLI..............................................................33
web-based via MMU ...........................................43
USB .............................................................5, 7, 10
Power Port
MAC and VLAN
standalone only....................................................12
Product Feature
table explanation................................................142
Management
descriptions..........................................................62
Radius Authentication
IP-based (web).................................................4, 58
MMU...............................................................4, 55
SNMP ..................................................................52
Telnet.....................................................................4
TN private MIBs..................................................53
USB .......................................................................4
description ...........................................................69
Redundant SFBRM SFP, 3-Port Switch
3-port switch mode..............................................16
accessing via IP ...................................................49
config screen........................................................50
redundant mode explanation................................15
revert option explanation (see note).....................15
MIB
standard counters.................................................68
MMU
Security
local switch settings.............................................44
CLI time out/idle .................................................71
IP Access .............................................................71
mac address blocking...........................................71
mac filtering.........................................................71
NMP access .........................................................72
radius authentication............................................71
USB access..........................................................72
username/passowrd..............................................72
VLAN management.............................................71
OAM
alternate loop back...............................................67
configuration........................................................60
critical events.......................................................65
device configuration management options ..........77
discovery..............................................................65
event notification with logging............................66
firmware upgrade.................................................81
last gasp/dying gasp.............................................67
operation admin maintenance..............................66
PDUs ...................................................................68
redundant model note ....................................60, 66
remote loop back .................................................67
what is?..................................................................2
Selective Link Pass Thru.......................................70
Set Up
CLI system config ...............................................37
COM port.............................................................29
COM port properties............................................31
IP configuration (directly to device)....................46
terminal emulator.................................................30
USB IP configuration ..........................................35
web-based to MMU.............................................43
Panel Front
BFFG gbit
ports and LEDs ................................................10
FBRM
ports and LEDs ..................................................5
FBRM gbit
ports and LEDs ..................................................7
SFBRM Redundant
ports and LEDs ................................................11
System Configuration
parameters (IP-based vs. chassis)......................131
Telnet
commands (directly to device).............................42
set up directly to standalone device.....................38
system config (directly to device)........................41
Panel Rear
Terminal Emulator
power connector ..................................................12
standalone models only........................................12
set up....................................................................30
USB
Pause
access...................................................................72
CLI access ...........................................................33
CLI device commands.........................................33
CLI system config ...............................................37
driver installation.................................................25
IP configuration...................................................35
flow control and back pressure............................69
Port Configuration
BFFG Gbit...........................................................13
FBRM Gbit..........................................................13
Ports
1000Base-FX/LX/BX......................................7, 10
100Base-FX/LX/BX..............................................5
144
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Download from Www.Somanuals.com. All Manuals Search And Download.
|