Trane Electric Heater TSC060 120 User Manual

Packaged Cooling with

Electric Heat Rooftop Units

Precedent^™

TSC060-120

50 Hz

RT-PRC016-EN

February 2004

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Introduction

Features and Benefits

Application Considerations

Selection Procedure

Model Number Description

General Data

Performance Data

Zone Controls

Electrical Data

Jobsite Connections

Dimensional Data

Weights

Mechanical Specifications

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Features and

Benefits

Easy Access Panels

Remove two screws for access to the

standardized internal components and

wiring.

Easy-Adjust Idler Arm

With the Easy-Adjust Idler Arm, the belt

and sheaves can be quickly adjusted

without moving the mounted fan motor.

The result is a major savings in time and

money.

Patented Condenser Coil

Precedent boasts a patented 1+1+1

Hybrid coil, permanently gapped for

easy of cleaning.

Unit Cabinet

The compact cabinet with rounded

corners takes up less room and is less

costly to ship. The beveled and ribbed

top is not only aesthetically pleasing, it is

designed to prevent water from pooling.

Single Point Power

A single electrical connection powers the

unit.

Colored And Numbered Wiring

You save time and money tracing wires

and diagnosing the unit.

Convertible Units

• The units ship in a downflow

configuration. They can be easily

converted to horizontal by simply

moving two panels.

Sloped Drain Pans

Every Precedent unit has a non-

corrosive, removable, double-sloped

drain pan that’s easy to clean and

reversible to allow installation of drain

trap on either side of the unit.

• Units come complete with horizontal

duct flanges so the contractor doesn’t

have to field fabricate them. These

duct flanges are a time and cost saver.

Compressors

Through the Base Condensate

Every unit includes provisions for

through the base condensate drain

connections. This allows the drain to be

connected through the roof curb instead

of a roof penetration.

Precedent^™contains the best

compressor technology available to

achieve the highest possible

performance. Our compressor line

includesTrane built reciprocating and

scrolls.

Foil-Faced Insulation

Easy Access Panels

All panels in the Evaporator section of

the unit have cleanable foil-faced

insulation. All edges are either captured

or sealed to ensure no fibers get into the

airstream.

Easy access panels reduce the number of

possible water entry points.

Low Ambient Cooling

All Precedent units have cooling

capabilities down to 0°F as standard.

Unit Base

For added water integrity, Precedent has

a raised 29 mm (1¹/8") lip around the

unit’s downflow supply and return to

prevent water from blowing into the

ductwork.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Features and

Benefits

Flexible Applications

Standardized Components

• Only two roof curbs for the 5-10 ton

Precedent line. . .simplifies curb

• R^see^ll^eia^cT^tie^olⁿm^.icroprocessor controls to

meet either the simple or the more

complex application.

• Components are placed in the same

location on all Precedent^™units.

Familiarize yourself with one Precedent

and you are familiar with every

Precedent.

• Airflow is outstanding. The Precedent

can replace an older machine with old

ductwork and, in many cases, improve

comfort through better air distribution.

• Belt drive — standard or oversized

supply fan motors meet a wide airflow

range.

• Precedent offers ultimate flexibility.

Options and components are not pre-

packaged at the factory. Units are built

to order in our standard “shortest in

the industry” ship cycle time.

Easy Access Low Voltage Terminal

Board

Precedent’s Low Voltage Terminal Board

is external to the electrical control

cabinet. It is extremely easy to locate and

attach the thermostat wire. This is

another cost and time saving installation

feature.

Low Voltage Connections

The wiring of the low voltage

connections to the unit and the zone

sensors is as simple as 1-1, 2-2, and 3-3.

This simplified system makes it easy for

the installer to wire

Single-Side Service

Single-side service is standard on all

Precedent units.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Features and

Benefits

• Eliminates the need for field-installed

components with its built-in anti-

short-cycle timer, time delay relay

and minimum ‘’on’’ time controls.

These controls are factory tested to

assure proper operation.

• Requires no special tools to run the

Precedent unit through its paces

during testing. Simply place a

jumper betweenTest 1 andTest 2

terminals on the Low Voltage

Terminal Board and the unit will walk

through its operational steps. The

unit automatically returns control to

the zone sensor after stepping

through the test mode a single time,

even if the jumper is left on the unit.

Micro Controls

Several years ago,Trane was the first to

introduce microprocessor controls into

the Light Commercial Market. That

design, along with immeasurable

experience, has provided the

technology for Trane’s second-

generation ReliaTel^™microprocessor

controls.

• As long as the unit has power and

the LED is lit, the Micro is

operational. The light indicates that

the Micro is functioning properly.

• Features expanded diagnostic

capabilities when used with Trane’s

Integrated Comfort ^™Systems.

• As an energy benefit, softens

electrical ‘’spikes’’ by staging on fans,

compressors and heaters.

ReliaTel^™Micro:

• Provides unit control for heating,

cooling, and ventilating by utilizing

input from sensors that measure

outdoor and indoor temperature.

• The Intelligent Fallback or Adaptive

Control is a benefit to the building

occupant. If a component goes

astray, the unit will continue to

operate at predetermined

• Improves quality and reliability

through the use of time-tested

microprocessor controls and logic.

temperature set points.

• Intelligent Anticipation is a standard

feature of the Micro. Functioning

constantly, the Micro and zone

sensors work together in harmony,

to provide tight comfort control.

• Prevents the unit from short cycling,

considerably improving compressor

life.

• Ensures that the compressor will run

for a specific amount of time, which

allows oil to return for better

lubrication, enhancing the reliability of

the compressor.

• Reduces the number of components

required to operate the unit, thereby

reducing possibilities for component

failure.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Features and

Benefits

Factory-installed Options

Hinged Access Doors

The following options round-out the

complete line of Precedent^™options:

These doors permit easy access to the

filter, fan/heat, and compressor/control

sections. They reduce the potential roof

damage from screws or sharp access

door corners.

— 0 - 50% Manual or Motorized

Outside Air

— Hail Protection Quality Coil Guards

— Electric Heaters (available as field

installed accessories)

Economizer

— Discharge Air Sensor

Equipped with either dry bulb, reference

or comparative enthalpy sensing, this

feature provides free cooling as the

outdoor temperature and/or humidity

decreases. Economizers, correctly

installed, offer a valuable energy

savings. Factory-installed economizers

save time and ensure proper installation.

— Wide array of Zone Sensors and

Thermostats

— Factory built Roof Curb

One of Our Finest Assets:

Trane Sales Representatives are a

Support group that can assist you with:

— Product

Phase Monitor

— Application

Phase monitor shall provide 100%

protection for motors and compressors

against problems caused by phase loss,

phase imbalance, and phase reversal.

Phase monitor is equipped with an LED

that provides an ON or FAULT indicator.

— Service

— Training

— Special Applications

— Specifications

— Computer Programs and much more

Precedent has the features and benefits

that make it first class in the light

commercial rooftop market. Designed

with input from field contractors and

engineers, its airflow performance is

outstanding.

Clogged Filter/Fan Fail Switches

These sensors allow a zone sensor

service light or Integrated Comfort

System to indicate a dirty filter or a fan

that’s not working. The field installation

charges for these valuable feedback

devices often eliminate them from

consideration. Factory installation can

make such features a good investment.

Precedent…The same Trane

quality…with added flexibility.

Comm-3/4Trane Communication

Interface

Available factory or field-installed. This

module when applied with ReliaTel^™

easily interfaces with Trane’s Integrated

Comfort^™System.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Features and

Benefits

Quality And Reliability Testing

• We perform a 100% coil leak test at the

factory. The evaporator and condenser

coils are leak tested at 1375 kPa (200

psig) and pressure tested to 3100 kPa

(450 psig).

• All Precedent^™designs were rigorously

rain tested at the factory to ensure

water integrity.

• Actual shipping tests were performed

to determine packaging requirements.

Units were test shipped around the

country to determine the best

packaging.

• All parts are inspected at the point of

final assembly. Sub-standard parts are

identified and rejected immediately.

• Every unit receives a 100% unit run test

before leaving the production line to

make sure it lives up to rigorousTrane

requirements.

• Factory shake and drop tests were

used as part of the package design

process to help assure that the unit

arrives at the job site in top condition.

We test designs at our factory not on

our customers!

• Rigging tests include lifting a unit into

the air and letting it drop one foot,

assuring that the lifting lugs and rails

hold up under stress.

VariTrac^™

VariTrac

When Trane’s changeover VAV System

for light commercial applications is

coupled with Precedent, it provides the

latest in technological advances for

comfort management systems and can

allow thermostat control in every zone

served by VariTrac.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Application

Considerations

Application of this product should be

within the cataloged airflow and cooling

considerations.

Condensate Trap

The evaporator is a draw-thru

configuration. A trap must be field

provided prior to start-up on the cooling

cycle.

Low Ambient Cooling

The Precedent^™line features, with

ReliaTel^™microprocessor controls, low

ambient cooling down to 18°C (0°F).

Contact your localTrane Representative

for more assistance with low ambient

cooling applications.

Clearance Requirements

The recommended clearances identified

with unit dimensions should be

maintained to assure adequate service

maximum capacity and peak operating

efficiency. Actual clearances which

appear inadequate should be reviewed

with the localTrane sales personnel.

Barometric Relief

This product line offers an optional

barometric relief damper. for use in

conjunction with economizer option.

This accessory consists of gravity

dampers which open with increased

pressure. As the building air pressure

increases, the pressure in the unit return

air section also increases, opening the

dampers and relieving the conditioned

space.

Unit Pitch

These units have reversible sloped

condensate drain pans. Units must be

installed level, any unit slope must be

toward the side of unit where

condensate drain is connected.

NOTE: THE EFFECTIVENESS OF

BAROMETRIC RELIEF DAMPER

DURING ECONOMIZING OPERATION

IS SYSTEM RELATED.

PRESSURE DROP OF THE RETURN AIR

SYSTEM SHOULD BE CONSIDERED TO

CONTROL BUILDING PRESSURIZA-

TION.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Selection

Procedure - SI Units

Cooling Capacity

Step 3

Heating Capacity

In order to select the correct unit which

meets the building’s requirements, the

fan motor heat must be deducted from

the gross cooling capacity.The amount

of heat that the fan motor generates is

dependent on the effort by the motor -

cfm and static pressure.To determine

the total unit static pressure:

Step 1

Calculate the building’s total and sensible

cooling loads at design conditions. Use

theTrane calculation methods or any

other standard accepted method.

Calculate the building heating load using

theTrane calculation form or other

standard accepted method.

Step 2

Factors used in unit selection:

Size the system heating capacity to

match the calculated building heating

load. The following are building heating

requirements:

Total Cooling Load: 16.7 kW

External Static (duct system)

110 Pa

Sensible Cooling Load: 11.7 kW

Standard Filter 1 in.

from Table PD-21

37 Pa

Total heating load of 5 kW

Airflow: 3400 m³/h

Economizer

5 Pa

2000 cfm

(100% Return Air)

Table PD-21

from

Electrical Characteristics: 380-415/50/3

380 volt/3 phase Power Supply

Electric Heater Size 7.5 kW

from Table PD-21

17 Pa

The electric heat accessory capacities are

listed inTable PD-23. From the table, the

smallest heater will deliver 7.5 kW at

380 V. Referring toTable ED-2, the

electric heater selection is

Summer Design Conditions: Entering

Evaporator Coil: 27 DB, 19 WB Outdoor

Ambient: 35

Total Static Pressure

169 Pa

Note: The Evaporator Fan Performance

Table PD-6 has deducted the pressure

drop for a 25 mm filter already in the

unit (see note belowTable PD-6).

Therefore, the actual total static pressure

is 169-17 (fromTable PD-21) = 152 Pa.

External Static Pressure: 110 Pa

BAYHTRR412A.

Air Delivery Selection

Step 2

External static pressure drop through the

air distribution system has been

calculated to be 110 Pa. FromTable PD-

21 static pressure drop through the

economizer is 5 Pa and the 7.5 kW heater

is 17 Pa (110 + 5 + 17). EnterTable PD-6

for a TSC060AD at 3400 m³/h and 132 Pa

static pressure. The standard motor will

give the desired airflow at a rated kW of

0.64.

Table PD-1 shows that aTSC060AD has a

gross cooling capacity of 17.8 kW and

14.4 kW sensible capacity at 3400 m³/h

and 35 DB outdoor ambient with 27 DB,

19 WB air entering the evaporator.

With 3400 m³/h and 152 Pa

Table PD-6 shows .67 kW for this unit.

Note below the table gives a formula to

calculate Fan Motor Heat,

To Find Capacity at Intermediate

Conditions Not in the Table

Fan Motor Heat (kw) =

1.144 x (Fan kW) + 0.132

When the design conditions are between

two numbers that are in the capacity

table, interpolation is required to

approximate the capacity. Note:

Extrapolation outside of the table

conditions is not recommended.

= 1.144 x 0.67 + 0.132 = 0.90 kW

Now subtract the fan motor heat from

the gross cooling capacity of the unit:

Net Total Cooling Capacity

Accessory Selection

Select accessories needed to

accommodate the application.

= 17.8 kW - 0.9 = 16.9 kW.

Net Sensible Cooling Capacity

= 14.4 kW - 0.9 = 13.5 kW.

Step 4

If the performance will not meet the

required load of the building’s total or

sensible cooling load, try a selection at

the next higher size unit.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Selection

Procedure - IP Units

Step 3

Heating Capacity

Cooling Capacity

In order to select the correct unit which

meets the building’s requirements, the

fan motor heat must be deducted from

the gross cooling capacity.The amount

of heat that the fan motor generates is

dependent on the effort by the motor -

cfm and static pressure.To determine

the total unit static pressure:

Step 1

Calculate the building heating load using

theTrane calculation form or other

standard accepted method.

Calculate the building’s total and sensible

cooling loads at design conditions. Use

theTrane calculation methods or any

other standard accepted method.

Step 2

Size the system heating capacity to

match the calculated building heating

load. The following are building heating

requirements:

Factors used in unit selection:

Total Cooling Load: 59 MBh

External Static (duct system)

0.45 wg

Sensible Cooling Load: 40 MBh

Standard Filter 1 in.

from Table PD-21a

0.15 wg

Total heating load of 15 MBH

Airflow: 2000 cfm

Economizer

0.02 wg

from

2000 cfm

(100% Return Air)

Table PD-21a

Electrical Characteristics: 380-415/50/3

380 volt/3 phase Power Supply

Electric Heater Size 26 MBh

from Table PD-21a

0.07 wg

The electric heat accessory capacities are

listed inTable PD-23a. From the table,

the smallest heater will deliver 26 MBh at

380 volts. Referring toTable ED-2, the

electric heater accessory selection is

BAYHTRR412A.

Summer Design Conditions: Entering

Evaporator Coil: 80 DB, 67 WB Outdoor

Ambient: 95

Total Static Pressure

0.69 wg

Note: The Evaporator Fan Performance

Table PD-6a has deducted the pressure

drop for a 1 in. filter already in the unit

(see note below Table PD-6a). Therefore,

the actual total static pressure is 0.69 -

0.15 (fromTable PD-21a) = 0.50 wg.

External Static Pressure: 0.45 in. wg

Step 2

Air Delivery Selection

Table PD-1a shows that aTSC060AD has

a gross cooling capacity of 62.0 MBh and

46.4 MBh sensible capacity at 2000 cfm

and 95 DB outdoor ambient with 80 DB,

67 WB air entering the evaporator.

External static pressure drop through the

air distribution system has been

calculated to be 0.45 inches of water.

FromTable PD-21a static pressure drop

through the economizer is 0.02 and the

26 kW heater is 0.07 inches of water (0.45

+ 0.02 + 0.07). EnterTable PD-6a for a

TSC060AD at 2000 cfm and 0.54 static

pressure. The standard motor will give

the desired airflow at a rated bhp of

about 1.01.

With 2000 cfm and 0.50 wg.

Table PD-6a shows .83 bhp for this unit.

Note below the table gives a formula to

calculate Fan Motor Heat,

To Find Capacity at Intermediate

Conditions Not in the Table

Fan Motor Heat (MBh) =

When the design conditions are between

two numbers that are in the capacity

table, interpolation is required to

approximate the capacity. Note:

Extrapolation outside of the table

conditions is not recommended.

2.915 x (Fan BHP) + 0.451

= 2.915 x 0.83 + 0.451 = 2.87 MBh

Now subtract the fan motor heat from

the gross cooling capacity of the unit:

Net Total Cooling Capacity

Accessory Selection

Select accessories needed to

accommodate the application.

= 62 MBh - 2.87 = 59.1 MBh.

Net Sensible Cooling Capacity

= 46.4 MBh - 2.87 = 43.5 MBh.

Step 5

If the performance will not meet the

required load of the building’s total or

sensible cooling load, try a selection at

the next higher size unit.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Model

Number

Description

C 060 A

3 4,5,6 7

10 11 12,13 14 15 16 17 18 19 20 21 22 23 24 25

Digit 1 - Unit Function

Digits 12, 13 - Service Sequence

** Factory Assigned

Digit 18 - Through the Base Provisions

T = DX Cooling

0 = No Through the Base Provisions

Digit 2 - Efficiency

Digit 14 - Fresh Air Selection

Digit 19 - Disconnect/Circuit Breaker/Phase

Monitor (3 phase only)

S = Standard Efficiency

0 = No Fresh Air

A = Manual Outside Air Damper 0-50%

B = Motorized Outside Air Damper 0-50%

C = Economizer, Dry Bulb 0-100%

without Barometric Relief

0 = No Disconnect or Circuit Breaker

3 = Phase Monitor Only (No Disconnect,

No Circuit Breaker)

Digit 3 - Airflow

C = Convertible

D = Economizer, Dry Bulb 0-100%

with Barometric Relief

E = Economizer, Reference Enthalpy

0-100% without Barometric Relief

F = Economizer, Reference Enthalpy

0-100% with Barometric Relief

G = Economizer, Comparative Enthalpy

0-100% without Barometric Relief

H = Economizer, Comparative Enthalpy

0-100% with Barometric Relief

Digit 20 - Convenience Outlet

Digits 4,5,6 - Nominal Gross Cooling

Capacity (MBh)

0 = No Convenience Outlet

060 = 17.6

072 = 21.1

090 = 26.4

102 = 29.9

120 = 35.1

Tons

Digit 21 - Communications Options

0 = No Communications Interface

1 = Comm-3/4 Communications Interface

2 = Comm-5 Communications Interface

7.5

8.5

Digit 22 - Refrigeration System Option

Digit 7 - Major Design Sequence

0 = Standard Refrigeration System

Digit 15 - Supply Fan/Drive Type/Motor

A = First

0 = Standard Drive

1 = Oversized Motor

Digit 23 - Refrigeration Controls

Digit 8 - Unit Voltage

0 = No Refrigeration Control

D = 380-415/50/3

Digit 16 - Hinged Service Access/Filters

Digit 24 - Smoke Detector

0 = Standard Panels/Standard Filters

A = Hinged Access Panels/Standard Filters

B = Standard Panels/

50 mm (2”) Pleated Filters

C = Hinged Access Panels/

50 mm (2”) Pleated Filters

Digit 9 - Unit Controls

R = ReliaTel^™Microprocessor

0 = No Smoke Detector

Digit 25 - Monitoring Controls

Digit 10 - Heating Capacity

0 = No Monitoring Control

1 = Clogged Filter Switch

2 = Fan Failure Switch

3 = Discharge Air Sensing Tube

4 = Clogged Filter Switch and Fan Fail

Switch

5 = Clogged Filter Switch and Discharge

Air Sensing Tube

6 = Fan Fail Switch and Discharge Air

Sensing Tube

0 = No Electric Heat

Digit 17 - Condenser Coil Protection

Digit 11 - Minor Design Sequence

0 = Standard Coil

A = First Sequence

1 = Standard Coil with Hail Guard

2 = Epoxy Coated Condenser Coil

3 = Epoxy Coated Condenser Coil with

Hail Guard

7 = Clogged Filter and Fan Fail Switches

and Discharge Air Sensing Tube

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

General

Data

Table GD - 1 — General Data

Convertible Units

TSC090AD

Convertible Units

TSC102AD

Convertible Units

TSC120AD

TSC060AD

TSC072AD

Cooling Performance ¹

Gross Capacity - kW (MBh)

COP (EER)²

18.2 (62.0)

2.99 (10.2)

3400 (2000)

17.3 (59.0)

5.78

23.2 (79.0)

3.08 (10.5)

4080 (2400)

3570 (2100)

22.0 (75.0)

7.14

26.7 (91.0)

3.02 (10.3)

5100 (3000)

4460 (2625)

25.2 (86.0)

8.35

31.1 (106.0)

3.02 (10.3)

5780 (3400)

5100 (3000)

29.9 (102.0)

9.90

34.9 (119.0)

2.99 (10.2)

6800 (4000)

5950 (3500)

33.1 (113.0)

11.08

Nominal Airflow - m³/h (cfm)

Rated Airflow - m³/h (cfm)

Net Capacity - kW (MBh)

System Power - kW

Compressor

Number -Type

Outdoor Sound Rating - dB ³

Outdoor Coil -Type

1-Climatuff Scroll

1-Trane 3-D Scroll

2-Climatuff Scroll

Lanced

Tube Size - in. OD

0.3125

1.02 (10.96)

3 / 17

0.3125

1.29 (13.88)

2 / 17

0.3125

1.29 (13.88)

2 / 17

0.3125

1.75 (18.89)

2 / 17

0.3125

2.41 (25.92)

2 / 17

Face Area - m²(sq ft)

Rows / FPI

Indoor Coil -Type

Lanced

Tube Size OD - in.

0.3125

0.62 (6.68)

3 / 16

0.3125

0.92 (9.89)

2 / 16

0.3125

0.92 (9.89)

3 / 16

0.3125

1.15 (12.36)

3 / 16

0.3125

1.15 (12.36)

4 / 16

Face Area - m²(sq ft)

Rows / FPI

Refrigerant Control

Drain Connection No. / Size - in.

Outdoor Fan -Type

No. Used / Diameter - in.

DriveType / No. Speeds

CFM

Short Orifice

1 / 0.75 NPT

Propeller

1 / 22

Direct / 1

2900

Short Orifice

1 / 0.75 NPT

Propeller

1 / 26

Direct / 1

5100

Short Orifice

1 / 0.75 NPT

Propeller

1 / 26

Direct / 1

5200

Short Orifice

1 / 0.75 NPT

Propeller

1 / 26

Direct / 1

5500

Short Orifice

1 / 0.75 NPT

Propeller

1 / 26

Direct / 1

5800

No. Motors / kW (HP)

Motor RPM

1 / 0.30 (0.40)

950

1 / .56 (0.75)

950

1 / .56 (0.75)

950

1 / .56 (0.75)

950

1 / .56 (0.75)

950

Belt Drive Indoor Fan -Type

No. Used

FC Centrifugal

Fan Diameter xWidth - mm (in.)

DrvieType / No. Speeds

No. Motors

280 X 280 (11 x 11)

Belt /Variable Speed

305 X 305 (12 x 12)

Belt /Variable Speed

305 X 305 (12 x 12)

Belt /Variable Speed

381 X 381 (15 x 15)

Belt /Variable Speed

381 X 381 (15 x 15)

Belt /Variable Speed

Standard Motor Power - kW (HP)

Oversized Motor Power - kW (HP)

Motor RPM - Standard / Oversized

Motor Frame Size

1.1 (1.5)

1.5 (2.0)

1450 / 1450

1.5 (2.0)

2.2 (3.0)

1450 / 2850

1.5 (2.0)

2.2 (3.0)

1450 / 2850

2.2 (3.0)

1450 / -

2850 / -

Filters - Type Furnished

(No.) Size Reccommended - mm

(No.) Size Reccommended - in.

Refrigerant Charge - kg (lbs) of R-22 ⁴

Throwaway

(2) 508 X 762 X 25

(2) 20 X 30 X 1

3.7 (8.2)

Throwaway

(4) 406 X 635 X 50

(4) 16 X 25 X 2

3.7 (8.2)

Throwaway

(4) 406 X 635 X 50

(4) 16 X 25 X 2

4.5 (10.0)

Throwaway

(4) 508 X 635 X 50

(4) 20 X 25 X 2

Circuit 1 - 3.8 (8.3)

Circuit 2 - 2.0 (4.4)

Throwaway

(4) 508 X 635 X 50

(4) 20 X 25 X 2

Circuit 1 - 3.4 (7.5)

Circuit 2 - 3.3 (7.3)

Notes:

1. Cooling Performance is rated at 35.0 C (95 F) ambient, 26.7 C (80 F) entering dry bulb, 19.4 C (67 F) entering wet bulb. Gross capacity does not include the effect of fan motor

heat. Net capacity includes the effect of fan motor heat. Units are suitable for operation to 20 % of nominal airflow.

2. EER are rated at ARI conditions.

3. Outdoor Sound rating shown is tested in accordance with ARI Standard 270. For more information refer to Performance Data Table "Sound Power Level".

4. Refrigerant charge is an approcimate value. For a more precise value, see unit nameplate and service literature.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-1 — Gross Cooling Capacities (kW) -TSC060AD - (SI)

Ambient Temperature (C)

Enter.

Dry

Bulb

Entering Wet Bulb Temperature (C)

19 22 16 19

m³/h

Temp

Airflow (C)

TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC

16.2 13.9 18.5 11.3 19.9 8.3 15.0 13.3 17.4 11.3 19.3 8.0 13.9 12.7 16.1 10.7 18.4 7.5 12.7 12.1 14.7 9.5 17.3 7.0

16.7 16.7 18.6 14.1 20.0 11.1 15.8 15.8 17.4 13.6 19.4 10.8 14.8 14.8 16.1 13.0 18.5 10.3 13.8 13.8 14.7 12.3 17.3 9.8

18.1 18.1 18.7 16.9 20.2 13.6 17.2 17.2 17.7 16.5 19.5 13.5 16.2 16.2 16.5 15.9 18.5 13.1 15.1 15.1 15.1 15.1 17.3 12.6

19.3 19.3 19.2 19.2 20.3 16.2 18.5 18.5 18.5 18.5 19.6 16.1 17.6 17.6 17.6 17.6 18.7 15.9 16.6 16.6 16.6 16.6 17.5 15.4

16.7 14.8 18.8 11.8 20.1 8.6 15.5 14.2 17.8 11.3 19.5 8.3 14.2 13.5 16.5 11.4 18.7 7.7 13.1 12.9 15.0 10.8 17.6 7.2

17.5 17.5 18.9 14.9 20.2 11.4 16.5 16.5 17.8 14.4 19.6 11.2 15.4 15.4 16.5 13.8 18.8 10.8 14.4 14.4 15.1 13.1 17.6 10.3

18.8 18.8 19.1 17.9 20.4 14.1 17.9 17.9 18.2 17.6 19.7 14.1 16.9 16.9 17.0 17.0 18.8 13.8 15.8 15.8 15.8 15.8 17.7 13.4

19.8 19.8 19.8 19.8 20.6 16.8 19.2 19.2 19.2 19.2 19.9 16.9 18.3 18.3 18.3 18.3 19.0 16.8 17.4 17.4 17.4 17.4 17.9 16.4

17.1 15.6 19.1 12.3 20.2 8.8 15.9 15.0 18.1 11.8 19.7 8.5 14.6 14.3 16.8 11.2 18.9 7.9 13.4 13.4 15.3 11.4 17.8 7.5

18.1 18.1 19.2 15.5 20.4 11.6 17.1 17.1 18.2 15.1 19.8 11.5 16.0 16.0 16.9 14.6 19.0 11.3 14.9 14.9 15.4 13.9 17.9 10.8

19.3 19.3 19.5 18.7 20.6 14.5 18.5 18.5 18.6 18.6 20.0 14.6 17.6 17.6 17.6 17.6 19.1 14.4 16.5 16.5 16.5 16.5 17.9 14.1

20.2 20.2 20.2 20.2 20.8 17.4 19.6 19.6 19.6 19.6 20.2 17.6 18.9 18.9 18.9 18.9 19.3 17.6 18.0 18.0 18.0 18.0 18.3 17.4

17.4 16.4 19.3 12.6 20.3 9.1 16.2 15.8 18.4 12.2 19.8 8.8 14.9 14.9 17.1 11.7 19.0 8.1 13.9 13.9 15.5 12.1 18.0 7.7

18.6 18.6 19.4 16.1 20.5 12.3 17.7 17.7 18.4 15.8 19.9 11.8 16.6 16.6 17.2 15.3 19.1 11.6 15.4 15.4 15.8 14.6 18.1 11.2

19.7 19.7 19.7 19.4 20.7 14.9 19.0 19.0 19.0 19.0 20.1 15.0 18.1 18.1 18.1 18.1 19.3 15.0 17.1 17.1 17.1 17.1 18.2 14.7

20.5 20.5 20.5 20.5 20.9 17.9 20.0 20.0 20.0 20.0 20.4 18.2 19.3 19.3 19.3 19.3 19.5 18.3 18.4 18.4 18.4 18.4 18.6 18.2

3060

3400

3740

4080

Notes:

1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.

2. TGC = Total Gross Capacity

3. SHC = Sensible Heat Capacity

Table PD-1a — Gross Cooling Capacities (MBH) ^_TSC060AD ^_(IP)

Ambient Temperature (F)

Enter.

Dry

Bulb

105

115

Entering Wet Bulb Temperature (F)

67 73 61 67

CFM

Temp

Airflow (F)

TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC

56.1 47.1 64.4 37.0 68.8 25.1 51.6 44.7 60.6 36.7 66.9 23.9 47.0 42.4 55.6 34.5 64.0 22.6 42.4 40.1 50.2 30.3 60.0 20.8

57.3 56.5 64.6 45.8 69.3 34.2 53.3 53.3 60.7 43.9 67.3 32.9 49.5 49.5 55.7 41.6 64.2 31.4 45.7 45.7 50.4 39.2 60.1 29.6

61.3 61.3 64.9 54.5 69.7 42.0 57.7 57.7 61.0 52.9 67.6 41.4 53.9 53.9 56.3 50.7 64.4 40.3 50.0 50.0 51.2 48.3 60.2 38.4

65.0 65.0 65.8 63.3 70.4 49.7 62.1 62.1 62.4 62.2 68.0 49.7 58.5 58.5 58.5 58.5 64.6 48.8 54.4 54.4 54.4 54.4 60.3 47.2

57.5 49.8 65.4 38.5 69.3 25.5 53.0 47.5 61.8 38.7 67.5 24.4 48.3 45.1 56.9 36.6 64.7 23.0 43.7 42.8 51.3 34.2 60.9 21.4

59.3 59.3 65.6 47.9 69.8 35.4 55.7 55.7 62.0 46.4 68.0 34.2 51.6 51.6 57.1 44.1 65.0 32.7 47.7 47.7 51.5 41.6 61.0 30.9

63.6 63.6 66.0 57.3 70.5 43.1 60.3 60.3 62.5 56.2 68.3 43.0 56.4 56.4 58.0 54.1 65.2 42.1 52.2 52.2 52.8 51.7 61.2 40.6

66.9 66.9 67.2 66.5 71.1 51.4 64.4 64.4 64.4 64.4 68.9 51.8 61.0 61.0 61.0 61.0 65.6 51.3 57.1 57.1 57.1 57.1 61.5 50.1

58.8 52.5 66.1 39.8 69.6 25.9 54.3 50.2 62.8 38.1 67.9 24.9 49.4 47.8 58.0 38.6 65.3 23.4 44.8 44.8 52.2 36.2 61.6 21.7

61.5 61.5 66.4 49.8 70.3 36.8 57.8 57.8 63.0 48.6 68.3 35.0 53.6 53.6 58.2 46.5 65.6 33.9 49.4 49.4 52.6 44.0 61.8 32.2

65.4 65.4 67.0 59.8 71.0 44.6 62.4 62.4 63.7 59.2 69.0 44.3 58.7 58.7 59.4 57.4 66.0 43.8 54.3 54.3 54.3 54.3 62.0 42.5

68.4 68.4 68.4 68.4 71.7 52.8 66.1 66.1 66.1 66.1 69.6 53.6 63.1 63.1 63.0 63.0 66.4 53.6 59.3 59.3 59.3 59.3 62.4 52.7

60.0 55.1 66.6 40.8 70.0 26.4 55.5 52.8 63.6 39.6 68.3 25.3 50.6 50.4 59.0 37.4 65.7 24.0 46.2 46.2 53.1 38.2 62.2 22.1

63.2 63.2 67.1 51.4 70.7 37.7 59.6 59.6 63.8 50.7 68.8 35.8 55.4 55.4 59.2 48.8 66.2 35.0 51.1 51.1 53.5 46.3 62.4 33.4

66.7 66.7 67.8 62.0 71.5 45.3 64.1 64.1 64.8 61.9 69.5 45.5 60.5 60.5 60.8 60.6 66.6 45.2 56.3 56.3 56.2 56.2 62.7 44.3

69.5 69.5 69.5 69.5 72.1 54.1 67.4 67.4 67.4 67.4 70.2 55.3 64.6 64.6 64.5 64.5 67.1 55.7 61.1 61.1 61.0 61.0 63.2 55.1

1800

2000

2200

2400

Notes:

1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.

2. TGC = Total Gross Capacity

3. SHC = Sensible Heat Capacity

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-2 — Gross Cooling Capacities (kW) -TSC072AD - (SI)

Ambient Temperature (C)

Enter.

Dry

Bulb

Entering Wet Bulb Temperature (C)

22 16 19

m³/h

Temp

Airflow (C)

TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC

20.9 17.5 23.3 14.6 24.6 10.3 19.7 16.8 22.4 13.6 24.0 9.9 18.4 16.1 21.2 12.9 23.2 9.4 17.1 15.4 19.7 12.9 22.0 9.0

21.6 21.2 23.4 17.4 24.8 13.5 20.4 20.4 22.5 17.0 24.1 13.3 19.4 19.4 21.2 16.4 23.3 12.8 18.2 18.2 19.8 15.7 22.1 12.3

22.9 22.9 23.6 20.6 25.0 16.5 22.1 22.1 22.7 20.4 24.3 16.3 21.0 21.0 21.5 19.9 23.5 16.1 19.9 19.9 20.2 19.2 22.2 15.6

24.0 24.0 24.1 23.8 25.2 19.4 23.4 23.4 23.3 23.3 24.5 19.3 22.5 22.5 22.4 22.4 23.6 19.3 21.4 21.4 21.4 21.4 22.3 18.8

21.5 18.5 23.6 15.2 24.8 10.6 20.3 17.9 22.8 14.2 24.2 10.1 19.0 17.2 21.6 13.6 23.4 9.8 17.6 16.4 20.1 12.9 22.3 9.3

22.3 22.3 23.8 18.1 25.1 14.5 21.3 21.3 22.9 17.9 24.3 13.6 20.2 20.2 21.6 17.3 23.6 13.4 19.0 19.0 20.2 16.6 22.4 12.8

23.6 23.6 24.0 21.6 25.3 17.6 22.9 22.9 23.2 21.5 24.6 16.8 21.8 21.8 22.0 21.1 23.7 16.7 20.7 20.7 20.8 20.5 22.5 16.3

24.6 24.6 24.6 24.6 25.5 20.0 23.9 23.9 23.9 23.9 24.8 20.1 23.1 23.1 23.1 23.1 23.9 20.1 22.1 22.1 22.1 22.1 22.7 19.8

22.0 19.5 23.9 15.8 25.0 10.7 20.8 18.9 23.1 14.7 24.4 10.4 19.5 18.2 21.9 14.2 23.5 10.1 18.1 17.4 20.5 13.5 22.5 9.6

22.9 22.9 24.0 18.7 25.3 13.9 22.1 22.1 23.2 18.6 24.5 13.9 20.9 20.9 22.0 18.2 23.7 13.6 19.7 19.7 20.6 17.6 22.6 13.3

24.1 24.1 24.3 22.4 25.5 17.4 23.4 23.4 23.5 22.4 24.8 17.3 22.5 22.5 22.5 22.2 23.9 17.2 21.3 21.3 21.3 21.3 22.8 17.0

25.0 25.0 25.0 25.0 25.7 20.7 24.4 24.4 24.4 24.4 25.1 20.8 23.7 23.7 23.7 23.7 24.2 20.8 22.6 22.6 22.6 22.6 23.1 20.7

22.4 20.3 24.1 16.3 25.2 10.9 21.2 19.8 23.2 15.1 24.5 10.7 19.9 19.1 22.2 14.7 23.6 10.3 18.5 18.4 20.8 14.0 22.7 9.9

23.4 23.4 24.3 19.3 25.5 14.5 22.6 22.6 23.4 19.2 24.7 14.7 21.5 21.5 22.3 19.0 23.8 14.0 20.3 20.3 20.9 18.4 22.8 13.7

24.5 24.5 24.6 23.2 25.6 17.8 23.8 23.8 23.9 23.2 25.0 17.8 23.0 23.0 23.0 23.0 24.1 17.7 21.8 21.8 21.8 21.8 23.0 17.7

25.4 25.4 25.4 25.4 25.9 21.2 24.8 24.8 24.8 24.8 25.3 21.4 24.1 24.1 24.1 24.1 24.4 21.4 23.1 23.1 23.1 23.1 23.4 21.6

3670

4080

4490

4900

Notes:

1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.

2. TGC = Total Gross Capacity

3. SHC = Sensible Heat Capacity

Table PD-2a — Gross Cooling Capacities (MBH) -TSC072AD - (IP)

Ambient Temperature (F)

Enter.

Dry

Bulb

105

115

Entering Wet Bulb Temperature (F)

67 73 61 67

CFM

Temp

Airflow (F)

TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC

72.2 59.1 80.6 47.1 85.1 31.0 67.5 56.5 77.7 44.1 82.7 29.6 62.6 53.9 73.0 41.8 79.9 28.0 57.4 51.2 67.5 39.2 75.5 26.0

73.8 70.7 81.0 56.1 85.8 42.2 69.4 68.2 77.9 55.0 83.4 40.7 65.0 65.0 73.1 52.6 80.4 39.0 60.6 60.6 67.6 50.0 75.8 36.8

77.7 77.7 81.4 66.3 86.3 51.7 74.3 74.3 78.2 65.6 83.8 50.1 70.3 70.3 73.6 63.5 80.7 49.2 66.0 66.0 68.3 61.0 76.1 47.4

81.3 81.3 82.4 76.3 87.1 59.8 78.8 78.8 79.4 76.0 84.6 59.4 75.1 75.1 75.3 74.6 81.3 59.0 70.8 70.8 70.7 70.7 76.6 57.4

74.2 62.5 81.6 49.2 85.7 31.5 69.3 59.9 78.7 46.0 83.4 30.1 64.4 57.3 74.2 43.7 80.2 28.5 59.1 54.6 68.9 41.1 76.3 26.6

76.1 75.0 82.1 58.2 86.5 43.7 72.1 72.1 79.0 57.4 84.2 42.1 67.9 67.9 74.4 55.4 80.9 40.4 63.3 63.3 69.0 53.0 76.8 38.4

80.0 80.0 82.6 69.1 86.8 52.8 77.1 77.1 79.5 68.7 84.7 51.6 73.1 73.1 75.3 67.3 81.4 50.7 68.7 68.7 70.1 65.0 77.2 49.4

83.3 83.3 83.8 79.7 87.1 61.5 80.7 80.7 80.9 79.4 85.5 61.5 77.5 77.5 77.5 77.5 82.1 61.1 73.3 73.3 73.3 73.3 77.8 60.2

75.8 65.6 82.3 50.7 86.2 32.0 71.0 63.2 79.4 49.8 84.0 30.7 66.0 60.6 75.4 45.6 80.7 29.0 60.6 57.8 70.0 42.9 77.0 27.2

78.1 78.1 82.9 60.1 87.2 44.1 74.6 74.6 79.8 59.4 84.7 44.3 70.3 70.3 75.6 58.1 81.2 41.3 65.7 65.7 70.1 55.7 77.6 39.8

81.7 81.7 83.6 71.6 88.2 54.0 79.1 79.1 80.5 71.3 85.4 53.6 75.4 75.4 76.6 70.7 82.0 52.1 70.9 70.9 71.6 68.7 78.1 51.3

84.8 84.8 85.0 82.5 89.1 62.3 82.3 82.3 82.3 82.3 86.1 61.2 79.4 79.4 79.4 79.4 82.8 63.0 75.2 75.2 75.2 75.2 78.7 62.8

77.0 68.3 82.9 52.2 86.6 32.5 72.5 66.4 80.0 51.4 84.5 31.2 67.5 63.7 76.2 47.1 81.2 29.5 62.1 61.0 70.8 44.7 77.6 27.8

79.6 79.6 83.7 61.8 87.6 44.7 76.6 76.6 80.6 61.3 85.4 44.0 72.4 72.4 76.5 60.5 81.8 42.1 67.7 67.7 71.1 58.2 78.1 40.9

83.0 83.0 84.4 73.9 88.7 54.9 80.4 80.4 81.5 73.9 86.2 54.1 77.1 77.1 77.8 73.8 82.7 53.5 72.7 72.7 72.9 71.9 78.8 53.0

85.9 85.9 86.0 85.0 89.6 65.2 83.6 83.6 83.6 83.6 87.0 63.2 81.0 81.0 81.0 81.0 83.5 65.0 76.8 76.8 76.8 76.8 79.5 65.3

2160

2400

2640

2880

Notes:

1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.

2. TGC = Total Gross Capacity

3. SHC = Sensible Heat Capacity

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-3 — Gross Cooling Capacities (kW) -TSC090AD - (SI)

Ambient Temperature (C)

Enter.

Dry

Bulb

Entering Wet Bulb Temperature (C)

19 22 16 19

m³/h

Temp

Airflow (C)

TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC

24.5 21.6 26.9 17.1 28.1 12.0 22.7 20.6 25.8 16.3 27.7 11.5 20.8 19.6 24.1 15.4 26.8 11.0 19.0 18.7 22.0 14.8 25.6 10.3

25.4 25.4 27.1 21.1 28.5 15.9 24.1 24.1 25.9 20.8 27.8 15.9 22.5 22.5 24.3 20.0 27.0 15.5 20.9 20.9 22.2 19.0 25.7 14.8

27.0 27.0 27.4 25.3 28.7 19.5 26.0 26.0 26.4 25.3 28.1 19.7 24.8 24.8 25.0 24.8 27.1 19.6 23.2 23.2 23.1 23.1 25.8 19.2

28.1 28.1 28.1 28.1 29.0 23.3 27.5 27.5 27.5 27.5 28.4 23.6 26.5 26.5 26.5 26.5 27.4 23.9 25.3 25.3 25.3 25.3 26.1 23.6

25.1 23.0 27.2 18.1 28.4 12.4 23.4 22.1 26.2 17.1 27.8 11.9 21.4 21.1 24.6 16.8 27.1 11.3 19.7 19.7 22.5 15.3 25.9 10.7

26.3 26.3 27.4 22.0 28.6 16.3 25.1 25.1 26.4 22.0 28.0 16.2 23.6 23.6 24.9 21.4 27.2 16.0 21.9 21.9 22.8 20.4 26.0 15.6

27.6 27.6 27.8 26.4 29.0 20.2 26.8 26.8 27.0 26.8 28.3 20.4 25.7 25.7 25.7 25.7 27.4 20.6 24.3 24.3 24.3 24.3 26.2 20.4

28.6 28.6 28.6 28.6 29.3 24.1 28.1 28.1 28.1 28.1 28.7 24.6 27.3 27.3 27.3 27.3 27.8 25.0 26.2 26.2 26.2 26.2 26.6 25.1

25.6 24.2 27.4 18.4 28.4 12.5 24.0 23.5 26.5 18.3 28.0 12.2 22.0 22.0 25.1 17.1 27.3 11.7 20.4 20.4 22.9 16.2 26.2 11.1

26.9 26.9 27.7 22.8 28.8 16.5 25.9 25.9 26.8 23.0 28.3 16.7 24.5 24.5 25.4 22.7 27.4 16.5 22.8 22.8 23.5 21.8 26.3 16.3

28.0 28.0 28.1 27.3 29.1 20.6 27.4 27.4 27.4 27.4 28.7 21.2 26.5 26.5 26.4 26.4 27.7 21.4 25.2 25.2 25.2 25.2 26.5 21.4

28.9 28.9 28.9 28.9 29.5 24.7 28.5 28.5 28.5 28.5 29.1 25.6 27.8 27.8 27.8 27.8 28.1 26.0 26.8 26.8 26.8 26.8 27.0 26.3

26.1 25.4 27.6 18.5 28.5 12.7 24.5 24.5 26.7 19.1 28.1 12.5 22.8 22.8 25.4 18.0 27.4 12.0 21.1 21.1 23.4 17.0 26.3 11.4

27.3 27.3 27.9 23.4 28.9 16.8 26.5 26.5 27.1 23.9 28.5 17.1 25.3 25.3 25.8 23.8 27.7 17.0 23.6 23.6 24.1 23.1 26.5 16.9

28.3 28.3 28.4 28.1 29.2 21.0 27.8 27.8 27.8 27.8 28.8 21.8 27.0 27.0 27.0 27.0 27.9 22.1 25.8 25.8 25.8 25.8 26.8 22.3

29.1 29.1 29.1 29.1 29.6 25.2 28.8 28.8 28.8 28.8 29.3 26.4 28.2 28.2 28.2 28.2 28.4 26.9 27.3 27.3 27.3 27.3 27.4 27.4

4590

5100

5610

6120

Notes:

1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.

2. TGC = Total Gross Capacity

3. SHC = Sensible Heat Capacity

Table PD-3a — Gross Cooling Capacities (MBH) -TSC090AD - (IP)

Ambient Temperature (F)

Enter.

Dry

Bulb

105

115

Entering Wet Bulb Temperature (F)

67 73 61 67

CFM

Temp

Airflow (F)

TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC

84.4 72.7 92.7 55.2 96.6 35.6 77.7 69.1 89.4 52.6 95.2 34.0 70.4 65.4 83.4 50.6 92.5 32.0 63.7 61.9 75.3 46.9 88.2 29.8

86.5 86.5 93.3 67.5 97.8 48.9 81.2 81.2 89.6 66.8 96.2 48.4 75.1 75.1 83.8 64.0 93.1 46.6 69.4 69.4 75.8 60.3 88.5 44.1

91.5 91.5 94.2 80.6 98.9 59.9 87.7 87.7 90.6 80.8 97.2 60.5 82.5 82.5 85.1 78.8 93.5 59.5 76.4 76.4 77.7 75.2 88.8 58.1

95.1 95.1 95.7 93.2 100.0 71.0 92.6 92.6 92.5 92.5 97.5 71.8 88.7 88.7 88.7 88.7 94.3 72.6 83.7 83.7 83.6 83.6 89.5 71.8

86.5 77.3 93.5 56.9 97.1 36.1 80.0 73.9 90.6 56.4 95.8 34.6 72.6 70.1 85.2 52.3 93.2 32.7 65.6 65.6 76.9 49.9 89.1 30.5

89.4 89.4 94.3 70.0 98.3 52.8 84.9 84.9 91.0 70.2 96.9 49.4 78.8 78.8 85.6 68.2 93.9 48.9 72.7 72.7 77.8 64.5 89.6 46.3

93.6 93.6 95.4 83.8 99.4 61.1 90.6 90.6 92.2 85.2 98.0 62.3 86.1 86.1 87.3 84.2 94.5 61.9 80.1 80.1 80.1 80.1 90.0 61.2

96.8 96.8 97.0 96.7 100.5 72.8 94.8 94.8 94.8 94.8 99.0 75.4 91.5 91.5 91.4 91.4 95.4 75.8 87.0 87.0 87.0 87.0 90.9 75.9

88.1 81.3 94.3 59.1 97.5 36.7 82.1 78.5 91.4 58.6 96.2 35.2 74.1 74.1 86.4 54.8 93.7 33.4 68.1 68.1 78.5 51.2 89.8 31.2

91.4 91.4 95.1 72.1 98.7 50.2 87.6 87.6 92.1 73.3 97.4 50.3 82.2 82.2 87.1 72.0 94.5 49.7 75.6 75.6 79.7 68.7 90.4 48.3

95.1 95.1 96.2 86.6 99.8 62.1 92.7 92.7 93.6 89.0 98.5 63.8 88.8 88.8 89.2 89.1 95.2 64.0 83.5 83.5 83.5 83.5 90.9 63.9

97.9 97.9 97.9 97.9 101.0 74.3 96.4 96.4 96.3 96.3 99.7 77.5 93.5 93.5 93.5 93.5 96.3 78.6 89.4 89.4 89.4 89.4 92.1 79.5

89.5 85.0 95.1 60.6 97.8 37.2 84.0 83.1 92.2 60.7 96.6 35.7 76.7 76.7 87.5 57.3 94.1 34.0 70.4 70.4 80.0 53.8 90.4 31.9

92.9 92.9 95.6 74.0 99.0 50.8 89.7 89.7 93.0 76.0 97.8 51.0 84.8 84.8 88.3 75.6 95.2 50.9 78.1 78.1 81.6 72.8 90.9 49.5

96.2 96.2 96.9 88.9 100.2 63.1 94.2 94.2 94.7 92.3 99.0 65.1 90.7 90.7 90.7 90.7 95.8 65.8 86.0 86.0 86.0 86.0 91.7 66.3

98.7 98.7 98.7 98.7 101.3 75.7 97.5 97.5 97.5 97.5 100.1 79.4 94.9 94.9 94.9 94.9 97.0 81.1 91.2 91.2 91.2 91.2 93.0 82.7

2700

3000

3300

3600

NOTES:

1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.

2. TGC = Total Gross Capacity

3. SHC = Sensible Heat Capacity

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-4 — Gross Cooling Capacities (kW) -TSC102AD - (SI)

Ambient Temperature (C)

Enter.

Dry

Bulb

Entering Wet Bulb Temperature (C)

19 22 16 19

m³/h

Temp

Airflow (C)

TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC

28.0 24.3 31.5 19.5 33.4 14.1 26.0 23.3 30.0 18.7 32.5 13.5 23.9 22.2 27.8 17.7 31.3 12.9 21.6 21.6 25.4 17.3 29.7 12.2

29.0 28.4 31.6 24.3 33.6 18.7 27.4 27.1 30.1 23.6 32.7 18.5 25.6 25.6 28.0 22.7 31.4 17.8 23.9 23.9 25.6 21.6 29.8 17.1

31.0 31.0 31.9 29.0 33.9 23.0 29.7 29.7 30.5 28.6 32.9 22.8 28.1 28.1 28.1 28.1 31.5 22.5 26.3 26.3 26.5 25.7 29.9 22.0

32.6 32.6 32.7 32.1 34.1 27.3 31.6 31.6 31.6 31.4 33.2 27.3 30.4 30.4 30.3 30.3 31.8 27.2 28.9 28.9 28.8 28.8 30.2 26.8

28.8 25.8 31.9 20.4 33.6 14.4 26.8 24.8 30.5 19.6 32.8 13.9 24.2 24.2 28.5 18.7 31.6 13.4 22.5 22.5 26.0 17.6 30.1 12.6

30.1 29.8 32.1 25.4 34.0 19.2 28.6 28.6 30.7 25.0 32.9 19.1 26.8 26.8 28.8 24.2 31.7 18.6 25.0 25.0 26.3 23.1 30.2 17.9

32.0 32.0 32.5 30.5 34.2 23.7 30.9 30.9 30.9 30.9 33.2 23.7 29.4 29.4 29.4 29.4 31.9 23.6 27.6 27.6 27.7 27.2 30.3 23.2

33.4 33.4 33.4 33.2 34.5 28.1 32.6 32.6 32.5 32.5 33.6 28.5 31.4 31.4 31.4 31.4 32.3 28.5 30.0 30.0 30.0 30.0 30.8 28.3

29.5 27.3 32.2 21.1 33.8 14.7 27.6 26.3 31.0 20.5 33.0 14.4 25.1 25.1 29.1 19.6 31.8 13.8 23.5 22.9 26.5 18.5 30.4 12.9

31.0 31.0 32.5 26.5 34.2 19.7 29.7 29.7 31.2 26.3 33.3 19.5 27.9 27.9 29.4 25.6 32.0 19.2 26.0 26.0 27.0 24.5 30.5 18.7

32.7 32.7 33.0 31.7 34.6 24.5 31.7 31.7 31.7 31.7 33.6 24.6 30.4 30.4 30.5 29.9 32.3 24.5 28.8 28.8 28.8 28.6 30.7 24.3

34.0 34.0 34.0 34.0 34.8 28.9 33.2 33.2 33.2 33.2 33.9 29.5 32.1 32.1 32.1 32.1 32.7 29.7 30.9 30.9 30.9 30.9 31.3 29.7

30.1 28.7 32.5 21.7 33.9 15.1 27.9 27.9 31.3 21.4 33.1 14.7 26.0 26.0 29.3 20.4 32.2 14.2 24.2 23.9 27.0 19.4 30.6 13.3

31.7 31.7 32.8 27.4 34.4 20.0 30.5 30.5 31.6 27.4 33.4 20.0 28.8 28.8 29.8 26.9 32.3 19.7 26.9 26.9 27.6 25.9 30.7 19.4

33.2 33.2 33.2 33.2 34.8 25.0 32.3 32.3 32.4 31.7 33.7 25.2 31.2 31.2 31.2 30.9 32.6 25.4 29.7 29.7 29.7 29.7 31.0 25.3

34.4 34.4 34.4 34.4 35.2 30.0 33.7 33.7 33.7 33.7 34.2 30.4 32.9 32.9 32.9 32.9 33.1 30.8 31.5 31.5 31.5 31.5 31.4 31.4

5200

5780

6360

6940

Notes:

1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.

2. TGC = Total Gross Capacity

3. SHC = Sensible Heat Capacity

Table PD-4a — Gross Cooling Capacities (MBH) -TSC102AD - (IP)

Ambient Temperature (F)

Enter.

Dry

Bulb

105

115

Entering Wet Bulb Temperature (F)

67 73 61 67

CFM

Temp

Airflow (F)

TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC

96.7 81.9 109.1 63.4 115.0 42.2 89.1 78.1 104.0 60.7 112.1 40.4 81.2 74.1 96.3 59.2 107.9 38.3 73.7 70.3 87.0 55.2 102.4 35.8

98.2 98.2 109.4 78.3 116.1 58.1 92.7 90.8 104.2 76.3 113.0 56.2 85.7 85.2 96.6 72.9 108.5 53.9 79.3 79.3 87.4 68.8 102.7 51.3

105.0 105.0 110.2 93.1 117.3 70.8 100.0 100.0 105.0 91.8 113.6 70.4 93.6 93.6 98.0 88.8 108.9 68.7 86.8 86.8 89.2 84.7 103.1 66.7

110.4 110.4 111.6 107.4 118.0 84.0 106.5 106.5 106.4 106.4 114.4 83.5 101.4 101.4 101.7 99.6 109.6 83.1 94.8 94.8 94.9 94.6 103.5 81.6

99.3 87.0 110.2 65.9 115.6 42.9 91.8 83.2 105.8 63.7 112.9 41.1 83.6 79.1 98.7 60.6 108.8 39.0 75.2 75.2 89.0 58.6 103.4 36.5

102.5 100.4 110.9 81.6 116.9 59.2 96.7 95.9 106.0 80.4 113.8 58.8 89.7 89.7 99.0 77.4 109.6 56.1 82.9 82.9 89.7 73.3 103.9 53.5

108.4 108.4 111.9 97.4 118.2 72.7 104.1 104.1 107.2 97.0 114.6 72.7 98.2 98.2 100.8 94.9 110.1 71.5 91.0 91.0 91.0 91.0 104.2 70.0

113.2 113.2 113.1 113.1 119.5 86.5 109.7 109.7 109.9 107.6 115.6 86.6 105.1 105.1 105.1 104.4 111.0 86.9 99.4 99.4 99.2 99.2 105.1 86.0

101.6 91.8 111.3 67.8 116.2 43.6 94.3 88.2 107.1 66.5 113.5 41.8 84.7 84.7 100.4 63.0 109.5 39.6 78.4 76.4 90.9 59.0 104.2 37.1

105.4 104.4 112.1 84.5 117.6 60.0 100.3 100.3 107.4 84.0 114.7 59.4 93.4 93.4 100.9 81.6 110.0 57.9 86.1 86.1 91.7 77.7 104.8 55.6

111.0 111.0 113.3 101.2 118.9 74.2 107.0 107.0 108.9 101.7 116.0 74.8 101.8 101.8 101.8 101.8 111.2 73.8 94.9 94.9 94.9 94.9 105.3 72.9

115.2 115.2 115.2 115.2 120.3 88.6 112.1 112.1 112.1 111.1 116.5 89.3 107.8 107.8 107.7 107.7 112.1 90.2 102.6 102.6 102.6 102.6 106.4 90.0

103.5 96.3 112.1 69.5 116.6 43.8 94.9 94.9 107.9 68.7 114.0 42.5 87.5 87.5 101.8 65.6 110.0 40.3 80.7 79.5 92.4 61.7 104.8 37.8

107.9 107.9 113.0 87.1 118.1 60.8 103.1 103.1 108.6 87.3 115.3 60.3 96.8 96.8 102.5 85.6 110.7 59.5 89.1 89.1 93.7 82.0 105.4 57.5

112.9 112.9 114.4 104.5 119.5 75.5 109.3 109.3 110.4 105.7 116.7 76.5 104.5 104.5 104.5 104.5 111.9 76.7 98.2 98.2 98.6 96.7 106.2 75.5

116.7 116.7 116.7 116.7 120.9 90.6 113.9 113.9 113.8 113.8 117.9 92.9 109.9 109.9 109.8 109.8 113.0 93.2 104.9 104.9 104.9 104.9 107.5 93.5

3060

3400

3740

4080

Notes:

1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.

2. TGC = Total Gross Capacity

3. SHC = Sensible Heat Capacity

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-5 — Gross Cooling Capacities (kW) -TSC120AD - (SI)

Ambient Temperature (C)

Enter.

Dry

Bulb

Entering Wet Bulb Temperature (C)

19 22 16 19

m³/h

Temp

Airflow (C)

TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC

31.9 28.6 35.3 22.8 37.2 15.9 29.6 27.4 33.6 21.7 36.5 15.4 27.1 26.2 31.0 20.5 35.2 14.8 24.6 24.6 28.4 19.9 33.2 14.0

33.4 33.4 35.5 28.2 37.7 21.4 31.6 31.6 33.9 27.8 36.7 21.4 29.5 29.5 31.3 26.6 35.3 20.7 27.5 27.5 28.9 25.5 33.3 19.9

35.5 35.5 36.0 33.8 38.1 26.5 34.2 34.2 34.5 33.8 37.0 26.7 32.3 32.3 32.2 32.2 35.5 26.6 30.4 30.4 30.4 30.4 33.4 25.9

37.1 37.1 37.1 37.1 38.5 31.6 36.2 36.2 36.2 36.2 37.3 31.9 34.8 34.8 34.8 34.8 35.9 32.3 33.2 33.2 33.2 33.2 34.0 31.8

32.7 30.4 35.7 23.8 37.5 16.3 30.5 29.3 34.2 22.8 36.8 15.9 27.8 27.8 31.9 21.8 35.5 15.3 25.7 25.7 29.0 21.2 33.7 14.5

34.5 34.5 36.0 29.5 38.0 21.9 32.9 32.9 34.5 29.4 37.0 22.0 30.9 30.9 32.3 28.5 35.7 21.7 28.7 28.7 29.7 27.4 33.8 21.0

36.3 36.3 36.6 35.4 38.4 27.4 35.3 35.3 35.3 35.3 37.3 27.6 33.7 33.7 33.7 33.7 35.9 27.8 31.8 31.8 31.7 31.7 34.0 27.5

37.9 37.9 37.8 37.8 38.9 32.8 37.0 37.0 37.0 37.0 37.8 33.3 35.9 35.9 35.9 35.9 36.5 33.9 34.4 34.4 34.4 34.4 34.7 33.8

33.5 32.2 36.0 24.7 37.8 16.9 31.1 31.1 34.7 23.9 37.0 16.3 28.9 28.9 32.4 22.9 35.8 15.7 26.6 26.6 29.6 22.5 34.1 14.9

35.3 35.3 36.4 30.6 38.2 22.4 34.0 34.0 35.0 30.8 37.4 22.7 32.0 32.0 33.0 30.2 36.0 22.5 29.9 29.9 30.5 29.1 34.2 22.0

37.0 37.0 37.0 37.0 38.7 28.1 36.1 36.1 36.1 36.1 37.9 28.9 34.7 34.7 34.7 34.7 36.4 29.1 32.9 32.9 32.9 32.9 34.5 29.0

38.4 38.4 38.3 38.3 39.2 33.7 37.7 37.7 37.7 37.7 38.4 34.9 36.7 36.7 36.7 36.7 37.0 35.4 35.3 35.3 35.3 35.3 35.3 35.3

33.9 33.9 36.3 24.9 37.9 17.3 32.0 32.0 35.0 25.6 37.5 16.1 29.8 29.8 32.8 23.9 36.1 16.2 27.5 27.5 29.8 23.6 34.4 15.3

35.9 35.9 36.7 31.7 38.5 22.8 34.8 34.8 35.5 32.2 37.7 23.2 32.9 32.9 33.6 31.9 36.3 23.2 30.6 30.6 30.6 30.6 34.5 23.0

37.5 37.5 37.5 37.5 38.9 28.8 36.7 36.7 36.7 36.7 38.1 29.8 35.5 35.5 35.5 35.5 36.7 30.2 33.7 33.7 33.7 33.7 34.9 30.5

38.8 38.8 38.7 38.7 39.5 34.6 38.4 38.4 38.2 38.2 38.7 36.1 37.3 37.3 37.3 37.3 37.4 36.7 36.0 36.0 36.0 36.0 36.0 36.0

6120

6800

7480

8160

Notes:

1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.

2. TGC = Total Gross Capacity

3. SHC = Sensible Heat Capacity

Table PD-5a — Gross Cooling Capacities (MBH) -TSC120AD - (IP)

Ambient Temperature (F)

Enter.

Dry

Bulb

105

115

Entering Wet Bulb Temperature (F)

67 73 61 67

CFM

Temp

Airflow (F)

TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC

109.9 96.4 122.1 73.8 128.5 47.6 101.2 92.1 116.7 70.3 125.9 45.7 91.8 87.5 107.7 67.7 121.6 43.4 82.1 82.1 97.2 63.2 115.0 40.9

113.5 113.5 122.6 90.4 129.9 65.7 106.6 106.6 117.1 89.2 127.2 65.0 99.0 99.0 108.4 85.4 122.2 62.4 91.0 91.0 98.2 81.0 115.2 59.7

120.2 120.2 123.8 108.0 131.3 80.9 115.2 115.2 118.5 107.9 127.8 81.5 108.1 108.1 110.5 104.9 122.6 80.6 100.3 100.3 100.3 100.3 115.4 78.4

125.4 125.4 125.4 125.4 132.7 96.3 121.8 121.8 121.8 121.8 128.7 97.3 116.4 116.4 116.4 116.4 123.6 98.2 109.2 109.2 109.2 109.2 116.4 97.0

112.7 102.4 123.1 75.6 129.3 48.4 104.2 98.3 118.5 73.6 126.9 46.6 93.7 93.7 109.9 70.9 122.7 44.3 85.6 85.6 99.3 67.2 116.5 41.9

117.3 117.3 124.1 94.1 130.8 66.9 111.1 111.1 119.0 94.0 128.2 66.8 103.5 103.5 110.8 90.8 123.5 65.3 95.2 95.2 100.8 86.6 116.8 62.5

123.2 123.2 125.6 112.8 132.3 82.9 119.0 119.0 120.8 114.1 129.5 84.5 112.5 112.5 112.5 112.5 124.1 84.2 104.9 104.9 104.8 104.8 117.1 83.0

127.9 127.9 127.9 127.9 133.8 99.2 124.9 124.9 124.9 124.9 130.8 102.4 120.2 120.2 120.2 120.2 125.3 103.1 113.9 113.9 113.8 113.8 118.4 102.9

115.1 108.2 124.5 77.5 130.0 49.2 107.0 104.4 119.8 77.6 127.6 47.4 97.3 97.3 111.7 73.2 123.6 45.2 88.7 88.7 101.1 71.1 117.6 42.7

120.1 120.1 125.3 97.3 131.6 67.9 114.9 114.9 120.6 98.4 129.0 68.2 107.3 107.3 112.9 96.1 124.5 68.1 98.9 98.9 103.1 92.0 118.0 65.1

125.5 125.5 127.0 116.9 133.1 84.7 121.9 121.9 122.8 119.6 130.5 87.0 116.4 116.4 116.3 116.3 125.3 88.0 108.7 108.7 108.7 108.7 118.4 87.0

130.0 130.0 129.7 129.7 134.7 101.8 127.3 127.3 127.2 127.2 131.9 105.9 123.0 123.0 123.0 123.0 126.7 107.5 117.2 117.2 117.2 117.2 120.2 108.4

117.1 113.2 125.5 81.7 130.6 50.0 108.8 108.8 120.8 80.6 128.3 48.2 100.5 100.5 113.2 76.3 124.3 46.1 91.6 91.6 102.7 72.1 118.5 43.6

122.3 122.3 126.5 100.7 132.2 68.9 117.8 117.8 122.0 102.4 129.8 69.5 110.5 110.5 114.9 101.3 125.7 69.3 102.2 102.2 105.2 97.3 119.0 67.7

127.2 127.2 128.4 121.1 133.8 86.3 124.1 124.1 124.1 124.1 131.2 89.2 119.0 119.0 119.0 119.0 126.5 90.9 112.0 112.0 112.0 112.0 119.7 90.9

131.3 131.3 131.5 131.5 135.4 104.2 129.3 129.3 129.0 129.0 132.8 108.9 125.2 125.2 125.2 125.2 127.8 111.4 119.8 119.8 119.8 119.8 121.7 113.3

3600

4000

4400

4800

Notes:

1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.

2. TGC = Total Gross Capacity

3. SHC = Sensible Heat Capacity

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-6 — Belt Drive Evaporator Fan Performance -TSC060AD - Downflow Configuration (SI)

External Static Pressure (Pascals)

100

RPM

1.12 Nom kW Standard Motor & Low Static Drive

125

RPM

150

RPM

175

RPM

200

RPM

225

RPM kW

250

RPM kW

m³/h

RPM

1.12 Nom kW Standard Motor & Drive

0.49 985 0.54 1023 0.59 1060 0.64

0.58 1028 0.64 1067 0.70 1104 0.76

2720

3060

3400

3740

4080

703

760

821

885

950

0.27

0.35

0.46

0.60

0.76

757

815

873

930

990

0.31

0.40

0.51

0.65

0.80

806

861

918

977

0.35

0.45

0.57

0.71

854

904

958

0.39

0.49

0.62

899

947

998

0.43

0.54

0.67

944

988

706

773

840

909

0.32

0.43

0.56

0.71

1036 0.71 1073 0.76 1111 0.82 1147 0.89

1089 0.88 1124 0.93 1158 0.98 1191 1.03

1143 1.06 1177 1.12 1209 1.17 1241 1.23

1016 0.77

1074 0.93

1053 0.82

1110 1.00

1034 0.87

External Static Pressure (Pascals)

300 325 350

RPM RPM

275

RPM

375

RPM

CFM

RPM

1.12 Nom kW Standard Motor & Drive

2720

3060

3400

3740

4080

Notes:

1093 0.69

1138 0.82

1182 0.96

1226 1.10

1272 1.29

1126 0.74

1171 0.87

1215 1.02

1258 1.17

1160 0.79

1203 0.93

1246 1.09

1290 1.25

1190 0.84

1232 0.98

1276 1.15

1222 0.90

1262 1.04

1306 1.21

1.12 Nom kW Standard Motor &

Hi Static Drive

←

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

Tested To Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1.12 kW - Fan Motor Heat (kW) = 1.144 x Fan kW + 0.132

Table PD-6a — Belt Drive Evaporator Fan Performance -TSC060AD - Downflow Configuration (IP)

External Static Pressure (Inches of Water)

.10

.20

.30

.40

.50

.60

.70

.80

.90

1.00

CFM

RPM BHP

RPM BHP RPM BHP RPM BHP RPM BHP

1-1/2 HP Standard Motor & Low Static Drive

1-1/2 HP Standard Motor & Drive

1600

1800

2000

2200

2400

703

760

821

885

950

0.36

0.47

0.62

0.80

1.02

757

815

873

930

990

0.41

0.54

0.69

0.87

1.08

806

861

918

977

0.47

0.60

0.76

0.95

854

904

958

1016 1.03

1074 1.25

0.52

0.66

0.83

899

947

998

1053 1.10

1110 1.34

0.58

0.72

0.90

944

988

0.65

985

0.73 1023 0.79 1060 0.86

706

773

840

909

0.42

0.57

0.75

0.96

0.78 1028 0.86 1067 0.94 1104 1.02

1036 0.96 1073 1.02 1111 1.10 1147 1.19

1089 1.17 1124 1.24 1158 1.31 1191 1.39

1143 1.419 1177 1.50 1209 1.57 1241 1.65

1034 1.16

External Static Pressure (Inches of Water)

1.10

1.20

1.30

1.40

1.50

CFM

RPM BHP

1-1/2 HP Standard Motor & Drive

1600

1800

2000

2200

2400

Notes:

1093 0.92

1138 1.10

1182 1.28

1226 1.48

1272 1.73

1126 0.99

1171 1.17

1215 1.37

1258 1.57

1160 1.06

1203 1.25

1246 1.46

1290 1.67

1190 1.13

1232 1.32

1276 1.54

1222 1.20

1262 1.39

1306 1.62

1-1/2 HP Standard Motor &

Hi Static Drive

←

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

Tested To Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1 1/2 HP - Fan Motor Heat (MBH) = 2.915 x Fan BHP + 0.451

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-7 - Belt Drive Evaporator Fan Performance-TSC060AD - Horizontal Configuration - (SI)

External Static Pressure (Pascals)

100

RPM

125

RPM

150

RPM

1.12 Nom kW Standard Motor & Drive

175

RPM

200

RPM

225

RPM kW

250

RPM kW

m³/h

RPM

1.12 Nom kW Std Motor & Low Static Drive

2720

3060

3400

3740

4080

707

778

850

923

997

0.26

0.36

0.48

0.63

0.80

774

840

908

978

0.31

0.41

0.54

0.69

837

897

961

1028 0.76

1096 0.94

0.37

0.48

0.60

898

953

1012 0.67

1075 0.83

1140 1.02

0.43

0.54

953

0.48

1001 0.54

1058 0.67

1111 0.81

1166 0.99

1223 1.18

1045 0.59 1087 0.65 1129 0.71 1168 0.77

1102 0.73 1143 0.79 1181 0.85 1219 0.92

1157 0.88 1198 0.95 1237 1.02 1274 1.09

1211 1.06 1254 1.14 1294 1.22 1330 1.29

1008 0.60

1062 0.74

1120 0.91

1183 1.10

1049 0.87

1266 1.27

1.12 Nom kW Standard Motor & Hi Static Drive

External Static Pressure (Pascals)

300 325 350

RPM RPM RPM

275

RPM

375

RPM

CFM

1.12 Nom kW Standard Motor & Drive

2720

3060

3400

3740

4080

1206 0.83

1256 0.99

1309 1.16

1241 0.89

1291 1.05

1343 1.24

1275 0.96

1326 1.12

1376 1.31

1306 1.02

1359 1.19

1338 1.09

1390 1.26

1.12 Nom kW Standard Motor &

Hi Static Drive

←

Notes:

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

Tested To Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1.12 kW - Fan Motor Heat (kW) = 1.144 x Fan kW + 0.132

Table PD-7a - Belt Drive Evaporator Fan Performance-TSC060AD - Horizontal Configuration - (IP)

External Static Pressure (Inches of Water)

0.10

0.20

0.30

0.40

0.50

0.60

0.70

0.80

0.90

1.00

CFM

RPM BHP

RPM BHP RPM BHP RPM BHP RPM BHP

1-1/2 HP Standard Motor &

Low Static Drive

1-1/2 HP Standard Motor & Drive

1600

1800

2000

2200

2400

707

778

850

923

997

0.35

0.48

0.65

0.84

1.07

774

840

908

978

0.42

0.56

0.73

0.93

837

897

961

1028 1.02

1096 1.27

0.50

0.64

0.81

898

953

1012 0.90

1075 1.12

1140 1.37

0.57

0.72

953

0.65

1001 0.72

1058 0.89

1111 1.09

1166 1.32

1223 1.59

1045 0.80 1087 0.87 1129 0.95 1168 1.03

1008 0.81

1062 1.00

1120 1.22

1183 1.48

1102 0.98 1143 1.06 1181 1.15 1219 1.23

1157 1.19 1198 1.28 1237 1.37 1274 1.47

1211 1.43 1254 1.53 1294 1.63 1330 1.74

1049 1.17

1266 1.70

1-1/2 HP Standard Motor & Hi Static Drive

External Static Pressure (Inches of Water)

1.10

RPM BHP

1.20

1.30

RPM BHP

1.40

RPM BHP

1.50

RPM BHP

CFM

RPM BHP

1/2 HP Standard Motor & Drive

1-1/2 HP Standard Motor & Hi Static Drive

1600

1800

2000

2200

2400

1206 1.12

1256 1.32

1309 1.56

1241 1.20

1291 1.41

1343 1.66

1275 1.28

1326 1.50

1376 1.76

1306 1.37

1359 1.60

1338 1.46

1390 1.69

Notes:

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

Tested To Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1 1/2 HP - Fan Motor Heat (MBH) = 2.915 x Fan BHP + 0.451

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-8 — Belt Drive Evaporator Fan Performance -TSC072AD - Downflow Configuration (SI)

External Static Pressure (Pascals)

100

RPM

1.12 Nom kW Standard Motor & Low Static Drive

125

RPM

150

RPM

1.12 Nom kW Standard Motor & Drive

175

RPM

200

RPM

225

RPM kW

250

RPM kW

m³/h

RPM

3260

3670

4080

4490

4890

573

602

635

670

706

0.25

0.31

0.38

0.47

0.58

630

656

682

715

749

0.30

0.37

0.45

0.54

0.64

680

706

732

758

789

0.36

0.43

0.51

0.60

0.71

726

751

777

802

830

0.41

0.49

0.58

0.68

0.79

769

792

818

845

870

0.47

0.55

0.64

0.75

0.87

811

832

856

883

909

0.52

0.61

0.71

0.82

0.95

851 0.58

871 0.67

893 0.77

919 0.89

945 1.02

889 0.65

908 0.74

930 0.84

953 0.96

979 1.10

548

584

621

660

0.26

0.33

0.42

0.51

569

612

0.35

0.45

1.12 Nom kW Standard Motor

& Hi Static Drive

External Static Pressure (Pascals)

300 325 350

RPM RPM

275

RPM

375

RPM

CFM

RPM

1.12 Nom kW Std Motor

& Drive

1.12 Nom kW Standard Motor

& Hi Static Drive

3260

3670

4080

4490

4890

925

944

964

986

0.71

0.81

0.91

1.04

960

978

998

1019 1.11

1043 1.26

0.77

0.87

0.99

994

0.83

1026 0.89

1043 1.01

1063 1.14

1082 1.27

1103 1.42

1057 0.95

1073 1.08

1092 1.21

1112 1.35

1133 1.51

1010 0.94

1030 1.06

1051 1.19

1073 1.34

1011 1.18

1.50 Nom kW Over-Sized Motor

& Hi Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

TestedTo Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1.12 kW - Fan Motor Heat (kW) = 1.144 x Fan kW + 0.132

1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464

Table PD-8a — Belt Drive Evaporator Fan Performance -TSC072AD - Downflow Configuration (IP)

External Static Pressure (Inches of Water)

.10

.20

.30

.40

.50

.60

.70

.80

.90

1.00

CFM

RPM BHP

RPM BHP RPM BHP RPM BHP RPM BHP

1-1/2 HP Standard Motor

Low Static Drive

1-1/2 HP Standard Motor

Drive

0.70

0.81

0.95

1.10

1.27

1920

2160

2400

2640

2880

573

602

635

670

706

0.34

0.42

0.52

0.64

0.78

630

656

682

715

749

0.41

0.50

0.60

0.72

0.86

680

706

732

758

789

0.48

0.58

0.69

0.81

0.96

726

751

777

802

830

0.55

0.65

0.77

0.91

1.06

769

792

818

845

870

0.62

0.73

0.86

1.01

1.16

811

851 0.78

871 0.90

893 1.04

919 1.20

945 1.37

889 0.87

908 0.99

930 1.13

953 1.29

979 1.48

548

584

621

660

0.35

0.45

0.56

0.69

832

856

883

909

569

612

0.47

0.60

1-1/2 HP Standard Motor

& Hi Static Drive

External Static Pressure (Inches of Water)

1.10

RPM BHP

1.20

RPM BHP

1.30

RPM BHP

1.40

RPM BHP

1.50

RPM BHP

CFM

1-1/2 HP Standard Mtr

& Drive

1920

2160

2400

2640

2880

925

944

964

986

0.95

1.08

1.22

1.39

960

978

998

1019 1.49

1043 1.69

1.03

1.17

1.32

994

1.11

1026 1.19

1043 1.36

1063 1.53

1082 1.71

1103 1.90

1057 1.27

1073 1.44

1092 1.63

1112 1.81

1133 2.02

1-1/2 HP Standard Motor

Hi Static Drive

1010 1.26

1030 1.42

1051 1.60

1073 1.79

←

1011 1.58

2 HP Over-Sized Mtr & Hi Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

Tested To Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1 1/2 HP - Fan Motor Heat (MBH) = 2.915 x Fan BHP + 0.451

2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-9 — Belt Drive Evaporator Fan Performance -TSC072AD - Horizontal Configuration (SI)

External Static Pressure (Pascals)

100

RPM

Low Static Drive

125

RPM

150

RPM

1.12 Nom kW Standard Motor

175

RPM

200

RPM

Drive

225

RPM kW

250

RPM kW

m³/h

RPM

1.12 Nom kW Standard Motor

3260

3670

4080

4490

4890

565

609

660

710

762

0.23

0.31

0.40

0.51

0.64

627

663

701

745

795

0.29

0.36

0.45

0.56

0.70

679

716

751

788

828

0.34

0.42

0.51

0.62

0.76

726

762

798

833

869

0.39

0.48

0.59

0.69

0.82

771

804

839

875

911

0.45

0.54

0.65

0.77

0.91

814

843

877

914

950

0.51

0.60

0.71

0.85

0.99

857

883

914

949

986

0.57

0.67

0.78

0.91

899 0.63

922 0.74

950 0.85

939 0.70

960 0.81

984 0.93

566

619

672

726

0.26

0.35

0.45

0.58

984 0.98 1016 1.06

1.07 1019 1.14 1051 1.22

1.12 Nom kW Standard Motor

& Hi Static Drive

1.12 Nom kW Standard Motor

Drive

External Static Pressure (Pascals)

300 325 350

RPM RPM RPM

275

RPM

375

RPM

CFM

1.12 Nom kW Standard Motor & Hi Static Drive

3260

3670

4080

4490

4890

978

996

1020 1.00

1049 1.14

1081 1.30

0.76

0.87

1015 0.83

1034 0.95

1055 1.08

1081 1.23

1112 1.38

1051 0.90

1069 1.02

1089 1.16

1113 1.31

1141 1.47

1086 0.97

1103 1.09

1122 1.23

1144 1.40

1170 1.57

1118 1.04

1136 1.17

1154 1.31

1176 1.48

1199 1.66

1.50 Nom kW Over-Sized Motor & Hi Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

Tested To Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1.12 kW - Fan Motor Heat (kW) = 1.144 x Fan kW + 0.132

1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464

Table PD-9a — Belt Drive Evaporator Fan Performance -TSC072AD - Horizontal Configuration (IP)

External Static Pressure (Inches of Water)

.10

.20

.30

.40

.50

.60

.70

.80

.90

1.00

CFM

RPM BHP

RPM BHP RPM BHP RPM BHP RPM BHP

1-1/2 HP Standard Motor & Low Static Drive

1-1/2 HP Standard Motor

Drive

1920

2160

2400

2640

2880

565

609

660

710

762

0.31

0.41

0.54

0.68

0.86

627

663

701

745

795

0.39

0.48

0.60

0.76

0.94

679

716

751

788

828

0.45

0.57

0.69

0.83

1.02

726

762

798

833

869

0.52

0.64

0.78

0.93

1.11

771

804

839

875

911

0.60

0.72

0.87

1.04

1.21

814

843

877

914

950

0.69

857

883

914

949

986

0.77

0.90

1.04

1.22

899 0.85

922 0.99

950 1.14

939 0.93

960 1.08

984 1.24

566

619

672

726

0.35

0.47

0.61

0.77

0.80

0.95

1.13

1.33

984 1.31 1016 1.42

1.44 1019 1.53 1051 1.63

1-1/2 HP Standard Motor

Drive

1-1/2 HP Std Motor & Hi Static Drive

External Static Pressure (Inches of Water)

1.10

RPM BHP

1.20

1.30

RPM BHP

1.40

RPM BHP

1.50

RPM BHP

CFM

RPM BHP

1-1/2 HP Standard Motor

Hi Static Drive

1920

2160

2400

2640

2880

978

996

1020 1.35

1049 1.53

1081 1.74

1.02

1.17

1015 1.11

1034 1.27

1055 1.45

1081 1.65

1112 1.86

1051 1.20

1069 1.36

1089 1.55

1113 1.76

1141 1.97

1086 1.30

1103 1.46

1122 1.66

1144 1.87

1170 2.10

1118 1.39

1136 1.56

1154 1.76

1176 1.98

1199 2.22

2 HP Over-Sized Motor

High Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

Tested To Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1 1/2 HP - Fan Motor Heat (MBH) = 2.915 x Fan BHP + 0.451

2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-10 — Belt Drive Evaporator Fan Performance -TSC090AD - Downflow Configuration (SI)

External Static Pressure (Pascals)

100

RPM

1.50 Nom kW Standard Motor & Low Static Drive

125

RPM

150

RPM

175

RPM

1.50 Nom kW Standard Motor

200

RPM

225

RPM kW

250

RPM kW

m³/h

RPM

Drive

4080

4590

5100

5610

6120

701

743

789

836

885

0.47

0.59

0.74

0.92

1.14

750

787

827

873

921

0.54

0.66

0.82

1.00

1.22

794

830

867

908

954

0.60

0.74

0.90

1.08

1.30

834

871

906

944

986

0.67

0.82

0.98

1.17

873

908

944

980

0.73

0.89

1.06

909 0.80

943 0.96

980 1.15 1013 1.23

945 0.87

977 1.04

699

747

797

848

0.53

0.68

0.85

1.06

703

755

809

0.61

0.77

0.96

713

771

0.69

0.88

1.26 1016 1.35 1050 1.45

1.39 1019 1.49 1052 1.58 1085 1.69

1.50 Nom kW Standard Motor

& Hi Static Drive

External Static Pressure (Pascals)

300 325 350

RPM RPM

275

RPM

375

RPM

CFM

RPM

1.50 Nom kW Std Motor

& Drive

1.50 Nom kW Standard Motor

& Hi Static Drive

4080

4590

5100

5610

6120

980

0.95

1013 1.02

1043 1.19

1076 1.39

1111 1.63

1148 1.89

1046 1.10

1074 1.27

1105 1.47

1141 1.72

1177 1.99

1076 1.17

1105 1.36

1134 1.56

1168 1.80

1204 2.08

1106 1.25

1134 1.44

1163 1.65

1197 1.90

1232 2.18

1010 1.11

1045 1.31

1081 1.54

1116 1.79

2.24 Nom kW Over-Sized Motor

& Hi Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

Tested To Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464

2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139

Table PD-10a — Belt Drive Evaporator Fan Performance -TSC090AD - Downflow Configuration (IP)

External Static Pressure (Inches of Water)

.10

.20

.30

.40

.50

.60

.70

RPM BHP RPM BHP RPM BHP RPM BHP

Drive

.80

.90

1.00

CFM

RPM BHP

2 HP Standard Motor

RPM BHP

Low Static Drive

RPM BHP

2 HP Standard Motor

2400

2700

3000

3300

3600

701

743

789

836

885

0.63

0.79

0.99

1.24

1.53

750

787

827

873

921

0.72

0.89

1.10

1.34

1.63

794

830

867

908

954

0.81

0.99

1.20

1.45

1.74

834

871

906

944

986

0.90

1.09

1.31

1.57

873

908

944

980

0.98

1.19

1.43

909 1.08

943 1.29

980 1.54 1013 1.65

945 1.17

977 1.39

699

747

797

848

0.70

0.91

1.15

1.42

703

755

809

0.81

1.03

1.29

713

771

0.93

1.19

1.69 1016 1.82 1050 1.94

1.87 1019 1.99 1052 2.13 1085 2.26

2 HP Standard Motor

& Hi Static Drive

External Static Pressure (Inches of Water)

1.10

RPM BHP

1.20

RPM BHP

1.30

RPM BHP

1.40

RPM BHP

1.50

RPM BHP

CFM

2 HP Standard Mtr

& Drive

2 HP Standard Motor &

Hi Static Drive

2400

2700

3000

3300

3600

980

1.27

1010 1.49

1045 1.76

1081 2.06

1116 2.39

1013 1.37

1046 1.47

1076 1.57

1105 1.82

1134 2.09

1168 2.42

1204 2.79

1106 1.68

1043 1.60

1076 1.87

1111 2.18

1148 2.53

1074 1.71

1105 1.98

1141 2.30

1177 2.66

1134 1.93

1163 2.21

1197 2.55

1232 2.93

3 HP Over-Sized Mtr & Hi Static Drive

Notes:

Data Includes Pressure Drop DueTo Wet Coils And Filters.

2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500

3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

Tested To Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-11 — Belt Drive Evaporator Fan Performance -TSC090AD - Horizontal Configuration (SI)

External Static Pressure (Pascals)

100

RPM

125

RPM

150

RPM

1.50 Nom kW Standard Motor

175

RPM

200

RPM

Drive

225

RPM kW

250

RPM kW

m³/h

1.50 Nom kW Std Motor & Low Static Drive

RPM

4080

4590

5100

5610

6120

673

738

805

873

942

0.42

0.56

0.74

0.96

1.22

718

773

837

903

970

0.47

0.62

0.81

1.03

1.30

769

817

870

930

996

0.54

0.68

0.87

1.10

1.37

814

862

912

963

0.61

0.76

0.94

1.17

855

904

951

1000 1.25

1052 1.52

0.67

0.85

1.03

893

941

989

0.73

0.92

929

975

0.81

965 0.88

999 0.96

702

771

842

913

0.51

0.68

0.89

1.14

0.98 1009 1.06 1041 1.14

1.12 1025 1.21 1056 1.28 1088 1.36

1037 1.34 1073 1.45 1106 1.55 1136 1.63

1086 1.61 1121 1.71 1153 1.82 1184 1.93

1021 1.45

1.50 Nom kW Standard Motor

Drive

1.50 Nom kW Standard Motor &

Hi Static Drive

2.24 Nom kW OS

Motor & Hi Static Drive

External Static Pressure (Pascals)

300 325 350

RPM RPM RPM

1.50 Nom kW Standard Motor & Hi Static Drive

275

RPM

375

RPM kW

CFM

4080

4590

5100

5610

6120

1035 1.04

1073 1.22

1117 1.44

1165 1.72

1215 2.04

1070 1.12

1104 1.31

1146 1.53

1194 1.80

1242 2.13

1104 1.19

1136 1.40

1176 1.62

1220 1.88

1269 2.22

1137 1.27

1167 1.48

1205 1.72

1248 1.98

1295 2.31

1168 1.35

1198 1.57

1233 1.82

1275 2.08

1319 2.40

2.24 Nom kW Over-Sized Motor & Hi Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

Tested To Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464

2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139

Table PD-11a — Belt Drive Evaporator Fan Performance -TSC090AD - Horizontal Configuration (IP)

External Static Pressure (Inches of Water)

.10

.20

.30

.40

.50

.60

.70

RPM BHP RPM BHP RPM BHP RPM BHP

Drive

.80

.90

1.00

CFM

RPM BHP

2 HP Std Motor & Low Static Drive

RPM BHP

2 HP Standard Motor

2400

2700

3000

3300

3600

673

738

805

873

942

0.56

0.76

1.00

1.29

1.63

718

773

837

903

970

0.63

0.83

1.08

1.38

1.74

769

817

870

930

996

0.72

0.92

1.17

1.47

1.84

814

862

912

963

0.82

1.02

1.26

1.57

855

904

951

1000 1.68

1052 2.04

0.90

1.13

1.38

893

941

989

0.98

1.23

929

975

1.08

965 1.18

999 1.29

702

771

842

913

0.68

0.91

1.19

1.53

1.32 1009 1.42 1041 1.52

1.51 1025 1.62 1056 1.72 1088 1.82

1037 1.80 1073 1.94 1106 2.08 1136 2.19

1086 2.16 1121 2.29 1153 2.44 1184 2.59

1021 1.94

2 HP Standard Motor

Drive

2 HP Std Motor & Hi Static Drive

3 HP Over-Sized Motor

& Hi Static Drive

External Static Pressure (Inches of Water)

1.10

RPM BHP

1.20

RPM BHP

1.30

RPM BHP

1.40

RPM BHP

1.50

RPM BHP

CFM

2 HP Standard Motor

Hi Static Drive

2400

2700

3000

3300

3600

1035 1.39

1073 1.64

1117 1.93

1165 2.30

1215 2.73

1070 1.50

1104 1.76

1146 2.05

1194 2.41

1242 2.86

1104 1.60

1136 1.87

1176 2.17

1220 2.52

1269 2.98

1137 1.70

1167 1.99

1205 2.31

1248 2.66

1295 3.10

1168 1.81

1198 2.11

1233 2.44

1275 2.79

1319 3.22

3 HP Over-Sized Motor

High Static Drive

Notes:

Data Includes Pressure Drop DueTo Wet Coils And Filters.

2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500

3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475

Factory Supplied Motors, In Commercial Equipment, Are

Definite Purpose Motors, Specifically Designed And

TestedTo Operate Reliably And Continuously At All

Cataloged Conditions. Using The Full Horsepower Range

Of Our Fan Motors As Shown In OurTabular Data Will

Not Result In NuisanceTripping Or Premature Motor

Failure. Our Product’s Warranty Will Not Be Affected.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-12 — Belt Drive Evaporator Fan Performance -TSC102AD - Downflow Configuration (SI)

External Static Pressure (Pascals)

100

RPM

1.50 Nom kW Standard Motor & Low Static Drive

125

RPM

150

RPM

175

RPM

1.50 Nom kW Standard Motor

200

RPM

225

RPM kW

250

RPM kW

m³/h

RPM

Drive

4620

5200

5780

6350

6930

613

650

689

729

770

0.45

0.55

0.68

0.82

0.98

655

688

724

764

804

0.54

0.64

0.76

0.92

1.09

695

725

759

795

834

0.62

0.73

0.86

1.01

1.19

733

761

792

826

864

0.71

0.83

0.96

1.11

1.30

769

796

825

857

892

0.81

0.93

1.07

1.22

1.40

802 0.90

828 1.03

856 1.18

887 1.34

920 1.52

833 1.00

861 1.13

887 1.28

916 1.46

948 1.64

611

651

693

738

0.48

0.59

0.72

0.89

612

659

706

0.51

0.64

0.80

622

671

0.56

0.71

1.50 Nom kW Standard

Motor & Hi Static Drive

External Static Pressure (Pascals)

375 400

RPM RPM

1.50 Nom kW Std Mtr & Hi Static Dr

275

RPM

1.50 Nom kW Std Mtr & Drive

300

RPM

325

RPM

350

RPM

425

RPM

450

RPM

475

RPM kW

500

RPM kW

m³/h

4620

5200

5780

6350

6930

863

891

917

945

976

1.11

1.24

1.40

1.58

1.78

892

919

946

974

1.21

1.35

1.51

1.70

920

946

974

1001 1.82

1029 2.04

1.33

1.46

1.63

946

973

1001 1.75

1028 1.95

1055 2.17

1.44

1.58

973

999

1026 1.88

1054 2.08

1081 2.30

1.55

1.71

999

1.67

1025 1.79 1050 1.90 1073 2.02 1098 2.14

1048 1.96 1072 2.09 1096 2.22 1119 2.34

1074 2.14 1099 2.27 1121 2.41 1143 2.55

1103 2.34 1126 2.48 1148 2.62 1170 2.76

1130 2.58 1154 2.72 1176 2.85 1199 3.01

1024 1.83

1051 2.01

1079 2.20

1105 2.43

1002 1.91

2.24 Nom kW Over-Sized Motor & High Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are Definite Purpose Motors, Specifically Designed AndTestedTo

Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors

As Shown In OurTabular Data Will Not Result In NuisanceTripping Or Premature Motor Failure. Our Product’s Warranty

Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464

2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139

Table PD-12a — Belt Drive Evaporator Fan Performance -TSC102AD - Downflow Configuration (IP)

External Static Pressure (Inches of Water)

.10

.20

.30

.40

.50

.60

.70

RPM BHP RPM BHP RPM BHP RPM BHP

Drive

769

.80

.90

1.00

CFM

RPM BHP

2 HP Standard Motor

RPM BHP

Low Static Drive

RPM BHP

2 HP Standard Motor

2720

3060

3400

3740

4080

613

650

689

729

770

0.60

0.74

0.91

1.10

1.32

655

688

724

764

804

0.72

0.85

1.02

1.23

1.46

695

725

759

795

834

0.84

0.98

1.15

1.35

1.60

733

761

792

826

864

0.95

1.11

1.29

1.49

1.74

1.08

1.25

1.43

1.64

1.88

802 1.21

828 1.38

856 1.58

887 1.79

920 2.04

833 1.34

861 1.52

887 1.72

916 1.96

948 2.20

611

651

693

738

0.64

0.79

0.97

1.19

796

825

857

892

612

659

706

0.68

0.86

1.08

622

671

0.76

0.96

2 HP Standard Motor &

Hi Static Drive

External Static Pressure (Inches of Water)

1.10

RPM BHP

2 HP Standard Mtr & Drive

1.20

RPM BHP

1.30

RPM BHP

1.40

RPM BHP

1.50

RPM BHP

1.60

RPM BHP

1.70

1.80

1.90

2.00

CFM

RPM BHP RPM BHP RPM BHP RPM BHP

2 HP Std Motor & Hi Static Drive

2720

3060

3400

3740

4080

863

891

917

945

976

1.48

1.66

1.87

2.11

2.38

892

919

946

974

1.63

1.81

2.03

2.28

920

946

974

1001 2.44

1029 2.73

1.78

1.96

2.18

946

973

1001 2.34

1028 2.61

1055 2.91

1.93

2.12

973

999

1026 2.52

1054 2.78

1081 3.09

2.08

2.29

999

2.24

1025 2.39 1050 2.55 1073 2.71 1098 2.88

1048 2.63 1072 2.80 1096 2.98 1119 3.14

1074 2.86 1099 3.05 1121 3.23 1143 3.41

1103 3.14 1126 3.32 1148 3.51 1170 3.71

1130 3.45 1154 3.65 1176 3.83 1199 4.03

1024 2.46

1051 2.69

1079 2.96

1105 3.26

1002 2.56

3 HP Over-Sized Motor & Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are Definite Purpose Motors, Specifically Designed AndTestedTo

Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors

As Shown In OurTabular Data Will Not Result In NuisanceTripping Or Premature Motor Failure. Our Product’s Warranty

Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500

3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-13 — Belt Drive Evaporator Fan Performance -TSC102AD - Horizontal Configuration (SI)

External Static Pressure (Pascals)

100

RPM

125

RPM

150

RPM

175

RPM

1.50 Nom kW Standard Motor

200

RPM

225

RPM kW

250

RPM kW

m³/h

RPM

1.50 Nom kW Std Mtr & Low Static Drive

Drive

4620

5200

5780

6350

6930

646

693

743

799

857

0.50

0.64

0.82

1.04

1.31

689

735

781

830

883

0.58

0.73

0.91

1.12

1.39

734

773

819

865

913

0.67

0.82

1.01

1.23

1.48

781

812

853

899

945

0.77

0.92

1.11

1.34

1.60

826

855

886

930

977

0.88

1.03

1.21

1.45

865

897

925

960

0.98

1.15

1.34

1.56

898 1.07

934 1.27

964 1.47 1000 1.60

994 1.68 1028 1.82

928 1.16

969 1.38

616

675

735

796

0.51

0.68

0.89

1.14

654

711

770

828

0.57

0.75

0.97

1.23

1.72 1006 1.84 1034 1.96 1061 2.08

1.50 Nom kW Std Mtr

& High Static Drive

2.24 Nom kW Over-Sized

Motor & High Static Drive

External Static Pressure (Pascals)

375 400

RPM RPM

275

RPM

300

RPM

325

RPM

350

RPM

425

RPM

450

RPM

475

RPM kW

500

RPM kW

m³/h

1.50 Nom kW Standard Motor & High Static Drive

4620

5200

5780

6350

6930

956

999

1034 1.73

1063 1.96

1093 2.23

1.25

1.49

982

1.33

1008 1.42

1052 1.68

1094 1.97

1129 2.26

1157 2.53

1033 1.51

1078 1.78

1120 2.08

1158 2.40

1188 2.70

1056 1.60

1101 1.88

1145 2.20

1185 2.53

1218 2.86

1079 1.69

1124 1.98

1168 2.31

1210 2.66

1245 3.01

1102 1.78 1125 1.87 1146 1.95 1168 2.04

1146 2.08 1168 2.18 1188 2.27 1209 2.37

1191 2.42 1213 2.53 1234 2.63 1254 2.74

1234 2.78 1256 2.90 1278 3.03 1299 3.15

1026 1.58

1067 1.86

1098 2.11

1125 2.38

1273 3.16 1297 3.31

2.24 Nom kW Over-Sized Motor & High Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are Definite Purpose Motors, Specifically Designed AndTestedTo

Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors

As Shown In OurTabular Data Will Not Result In NuisanceTripping Or Premature Motor Failure. Our Product’s Warranty

Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464

2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139

Table PD-13a — Belt Drive Evaporator Fan Performance -TSC102AD - Horizontal Configuration (IP)

External Static Pressure (Inches of Water)

.10

.20

.30

.40

.50

.60

.70

.80

.90

1.00

CFM

RPM BHP

RPM BHP RPM BHP RPM BHP RPM BHP

2 HP Std Mtr & Low Static Drive

2 HP Standard Motor

Drive

2720

3060

3400

3740

4080

646

693

743

799

857

0.67

0.86

1.10

1.40

1.76

689

735

781

830

883

0.78

0.98

1.22

1.51

1.86

734

773

819

865

913

0.90

1.10

1.36

1.65

1.99

781

812

853

899

945

1.04

1.23

1.49

1.79

2.15

826

855

886

930

1.18

1.39

1.62

1.94

865

897

925

960

1.31

1.55

1.79

2.09

898 1.44

934 1.70

964 1.97 1000 2.14

994 2.26 1028 2.44

928 1.56

969 1.85

616

675

735

796

0.69

0.92

1.20

1.53

654

711

770

828

0.77

1.01

1.30

1.65

977

2.30 1006 2.47 1034 2.63 1061 2.79

3 HP Over-Sized Mtr & Drive

2 HP Std Motor &

Hi Static Drive

External Static Pressure (Inches of Water)

1.10

RPM BHP

2 HP Standard Motor

1.20

RPM BHP

1.30

RPM BHP

High Static Drive

1008 1.91

1052 2.26

1094 2.64

1129 3.03

1157 3.40

1.40

RPM BHP

1.50

RPM BHP

1.60

RPM BHP

1.70

RPM BHP RPM BHP RPM BHP RPM BHP

3 HP Over-Sized Motor Drive

1102 2.38 1125 2.5 1146 2.62 1168 2.74

1146 2.79 1168 2.92 1188 3.05 1209 3.18

1191 3.24 1213 3.39 1234 3.53 1254 3.68

1234 3.73 1256 3.89 1278 4.06 1299 4.23

1.80

1.90

2.00

CFM

2720

3060

3400

3740

4080

956

999

1.67

1.99

982

1.79

1033 2.03

1078 2.39

1120 2.79

1158 3.21

1188 3.62

1056 2.14

1101 2.52

1145 2.94

1185 3.39

1218 3.83

1079 2.26

1124 2.66

1168 3.09

1210 3.56

1245 4.03

1026 2.12

1067 2.49

1098 2.84

1125 3.19

1034 2.32

1063 2.63

1093 2.99

1273 4.24 1297 4.44

3 HP Over-Sized Motor

Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are Definite Purpose Motors, Specifically Designed AndTestedTo

Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors

As Shown In OurTabular Data Will Not Result In NuisanceTripping Or Premature Motor Failure. Our Product’s Warranty

Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500

3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-14 — Belt Drive Evaporator Fan Performance -TSC120AD - Downflow Configuration (SI)

External Static Pressure (Pascals)

100

RPM

2.24 Nom kW Standard Motor & Low Static Drive

125

RPM

150

RPM

175

RPM

2.24 Nom kW Standard Motor

200

RPM

225

RPM kW

250

RPM kW

m³/h

RPM

Drive

5440

6120

6800

7480

8160

718

764

814

864

916

0.72

0.90

1.11

1.36

1.64

754

797

844

894

945

0.82

0.99

1.21

1.48

1.77

789

829

874

922

972

0.93

1.10

1.32

1.59

1.90

822

860

903

948

997

1.03

1.22

1.44

1.70

856 1.14

892 1.34

932 1.56

887 1.25

922 1.46

960 1.69

731

782

834

887

0.81

1.01

1.24

1.52

715

773

833

0.81

1.04

1.31

747

803

861

0.90

1.14

1.42

741

803

0.95

1.21

975 1.82 1001 1.95

2.02 1022 2.14 1046 2.27

External Static Pressure (Pascals)

375 400

RPM RPM

275

RPM

300

RPM

325

RPM

350

RPM

425

RPM

450

RPM

475

RPM kW

500

RPM kW

m³/h

2.24 Nom kW Standard Motor & Drive

5440

6120

6800

7480

8160

917

951

988

1028 2.09

1071 2.41

1.36

1.57

1.82

945

979

1015 1.95

1053 2.23

1095 2.55

1.47

1.69

973

1.60

999

1.72

1024 1.84

1059 2.07

1093 2.35

1128 2.66

1166 3.02

1048 1.97

1082 2.20

1117 2.48

1152 2.81

1189 3.17

1072 2.10 1095 2.23 1117 2.37 1140 3.36

1107 2.34 1130 2.49 1152 2.63 1173 3.71

1142 2.63 1164 2.76 1187 2.91 1209 4.11

1007 1.82

1042 2.08

1078 2.38

1119 2.70

1033 1.94

1068 2.21

1103 2.52

1142 2.86

1176 2.95 1198 3.10 1221 3.25

1212 3.33

2.24 Nom kW Standard Motor & High Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are Definite Purpose Motors, Specifically Designed AndTestedTo

Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors

As Shown In OurTabular Data Will Not Result In NuisanceTripping Or Premature Motor Failure. Our Product’s Warranty

Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139

Table PD-14a — Belt Drive Evaporator Fan Performance -TSC120AD - Downflow Configuration (IP)

External Static Pressure (Inches of Water)

.10

.20

.30

.40

.50

.60

.70

RPM BHP RPM BHP RPM BHP RPM BHP

3 HP Standard Motor Drive

.80

.90

1.00

CFM

RPM BHP

3 HP Standard Motor

RPM BHP

Low Static Drive

3200

3600

4000

4400

4800

718

764

814

864

916

0.97

1.20

1.49

1.82

2.20

754

797

844

894

945

1.10

1.33

1.63

1.98

2.38

789

829

874

922

972

1.25

1.48

1.77

2.13

2.55

822

860

903

948

997

1.38

1.63

1.93

2.28

856 1.53

892 1.79

932 2.09

887 1.67

922 1.95

960 2.27

731

782

834

887

1.08

1.35

1.67

2.04

715

773

833

1.09

1.40

1.76

747

803

861

1.21

1.53

1.90

741

803

1.27

1.62

975 2.44 1001 2.62

2.71 1022 2.87 1046 3.04

External Static Pressure (Inches of Water)

1.10

RPM BHP

1.20

RPM BHP

3 HP Standard Motor & Drive

1.30

RPM BHP

1.40

1.50

RPM BHP

1.60

RPM BHP

1.70

1.80

1.90

2.00

CFM

RPM BHP

RPM BHP RPM BHP RPM BHP RPM BHP

3200

3600

4000

4400

4800

917

951

988

1028 2.81

1071 3.23

1.82

2.11

2.44

945

979

1015 2.62

1053 3.00

1095 3.42

1.97

2.27

973

2.14

999

2.30

1024 2.47

1059 2.78

1093 3.15

1128 3.57

1166 4.04

1048 2.65

1082 2.95

1117 3.33

1152 3.77

1189 4.25

1072 2.82 1095 3.00 1117 3.17 1140 3.36

1107 3.14 1130 3.33 1152 3.52 1173 3.71

1142 3.52 1164 3.70 1187 3.91 1209 4.11

1007 2.43

1042 2.79

1078 3.19

1119 3.62

1033 2.60

1068 2.97

1103 3.38

1142 3.83

1176 3.96 1198 4.15 1221 4.36

1212 4.46

3 HP Standard Motor & High Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are Definite Purpose Motors, Specifically Designed AndTestedTo

Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors

As Shown In OurTabular Data Will Not Result In NuisanceTripping Or Premature Motor Failure. Our Product’s Warranty

Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-15 — Belt Drive Evaporator Fan Performance -TSC120AD - Horizontal Configuration (SI)

External Static Pressure (Pascals)

100

RPM

2.24 Nom kW Standard Motor & Low Static Drive

125

RPM

150

RPM

175

RPM

2.24 Nom kW Standard Motor

200

RPM

225

RPM kW

250

RPM kW

m³/h

RPM

Drive

1.28 965 1.41 1000 1.53

1.53 1002 1.67 1038 1.81

5440

6120

6800

7480

8160

691

761

833

905

977

0.67

0.91

1.22

1.58

2.02

730

792

860

931

0.75

0.99

1.29

1.67

771

829

890

955

0.84

1.08

1.38

1.75

807

865

923

983

0.94

1.19

1.50

1.86

844

898

956

1.04

1.30

1.62

886

930

986

1.16

1.41

926

965

729

802

876

950

0.84

1.13

1.49

1.91

1.73 1015 1.85 1044 1.98 1077 2.12

1014 1.99

1074 2.42

1045 2.12 1072 2.25 1098 2.37 1125 2.51

1102 2.56 1131 2.71 1156 2.84 1181 2.98

1002 2.11

1025 2.20

1048 2.30

2.24 Nom kW Standard Motor & High Static Drive

External Static Pressure (Pascals)

375 400

RPM RPM

275

RPM

300

RPM

325

RPM

350

RPM

425

RPM

450

RPM

475

RPM kW

500

RPM kW

m³/h

2.24 Nom kW Std Mtr & Drive

5440

6120

6800

7480

8160

1029 1.64

1072 1.95

1111 2.28

1152 2.65

1205 3.12

1057 1.75

1106 2.10

1143 2.43

1182 2.81

1229 3.27

1084 1.86

1134 2.22

1174 2.58

1211 2.97

1108 1.96

1160 2.35

1204 2.74

1241 3.14

1132 2.06

1185 2.47

1232 2.90

1270 3.31

1155 2.17

1209 2.59

1260 3.05

1177 2.27 1198 2.37 1219 2.48 1239 3.46

1231 2.70 1252 2.82 1274 2.94 1295 4.10

1283 3.18 1306 3.32

2.24 Nom kW Standard Motor & High Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are Definite Purpose Motors, Specifically Designed AndTestedTo

Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors

As Shown In OurTabular Data Will Not Result In NuisanceTripping Or Premature Motor Failure. Our Product’s Warranty

Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139

Table PD-15a — Belt Drive Evaporator Fan Performance -TSC120AD - Horizontal Configuration (IP)

External Static Pressure (Inches of Water)

.10

.20

.30

.40

.50

.60

.70

RPM BHP RPM BHP RPM BHP RPM BHP

Drive

926

965

2.32 1015 2.48 1044 2.65 1077 2.85

1045 2.84 1072 3.01 1098 3.18 1125 3.36

1102 3.43 1131 3.63 1156 3.81 1181 4.00

.80

.90

1.00

CFM

RPM BHP

3 HP Standard Motor & Low Static Drive

RPM BHP

3 HP Standard Motor

3200

3600

4000

4400

4800

691

761

833

905

977

0.89

1.22

1.63

2.12

2.70

730

792

860

931

1.00

1.32

1.73

2.24

771

829

890

955

1.13

1.45

1.86

2.35

807

865

923

983

1.26

1.60

2.01

2.49

844

898

956

1014 2.66

1074 3.24

1.39

1.74

2.17

886

930

986

1.55

1.89

1.72

965 1.89 1000 2.06

2.06 1002 2.24 1038 2.43

729

802

876

950

1.13

1.52

1.99

2.56

1002 2.84

1025 2.96

1048 3.08

3 HP Standard Motor

High Static Drive

External Static Pressure (Inches of Water)

1.10

RPM BHP

3 HP Std Mtr & Drive

1.20

RPM BHP

1.30

RPM BHP

1.40

1.50

RPM BHP

1.60

RPM BHP

1.70

1.80

1.90

2.00

CFM

RPM BHP

RPM BHP RPM BHP RPM BHP RPM BHP

3200

3600

4000

4400

4800

1029 2.20

1072 2.62

1111 3.05

1152 3.55

1205 4.19

1057 2.35

1084 2.49

1134 2.98

1174 3.47

1211 3.99

1108 2.63

1160 3.15

1204 3.68

1241 4.21

1132 2.77

1185 3.31

1232 3.88

1270 4.44

1155 2.91

1209 3.47

1260 4.09

1177 3.05 1198 3.18 1219 3.32 1239 3.46

1231 3.63 1252 3.78 1274 3.94 1295 4.10

1106 2.81

1143 3.26

1182 3.76

1229 4.39

1283 4.27 1306 4.46

3 HP Standard Motor

High Static Drive

Notes:

Factory Supplied Motors, In Commercial Equipment, Are Definite Purpose Motors, Specifically Designed AndTestedTo

Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors

As Shown In OurTabular Data Will Not Result In NuisanceTripping Or Premature Motor Failure. Our Product’s Warranty

Will Not Be Affected.

Data Includes Pressure Drop DueTo Wet Coils And Filters.

3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-16 — Standard Motor & Sheave/Fan Speed (RPM)

Unit

6 Turns

Open

N/A

5 Turns

Open

898

698

752

4 Turns

Open

967

751

806

3 Turns

Open

1036

806

860

786

2 Turns

Open

1105

859

914

835

1 Turns

Open

1174

913

968

885

Model No.

TSC060AD

TSC072AD

TSC090AD

TSC102AD

TSC120AD

Closed

1243

967

1020

934

N/A

688

782

737

838

894

950

1006

1062

Factory set at 3 turns open

Table PD-17 — Standard Motor & Low Static Drive Accessory Sheave/Fan Speed (RPM)

Unit

6 Turns

Open

N/A

5 Turns

Open

691

537

671

4 Turns

Open

760

590

714

3 Turns

Open

829

644

757

2 Turns

Open

898

698

800

1 Turns

Open

967

752

843

Model No.

TSC060AD

TSC072AD

TSC090AD

TSC102AD

TSC120AD

Closed

1036

806

886

811

N/A

629

717

664

754

701

799

737

844

773

885

922

Factory set at 3 turns open

Table PD-18 — Standard Motor & High Static Drive Accessory Sheave/Fan Speed (RPM)

Unit

6 Turns

Open

N/A

1020

936

5 Turns

Open

1243

967

1073

981

4 Turns

Open

1311

1021

1127

1032

1174

3 Turns

Open

1379

1075

1181

1083

1229

2 Turns

Open

1450

1128

1235

1134

1285

1 Turns

Open

1515

1183

1289

1182

1341

Model No.

TSC060AD

TSC072AD

TSC090AD

TSC102AD

TSC120AD

Closed

1588

1235

N/A

1062

1118

Factory set at 3 turns open

Table PD-19 — Oversized Motor & Drive Sheave/Fan Speed (RPM)

Unit

6 Turns

Open

N/A

1112

N/A

5 Turns

Open

967

1182

971

4 Turns

Open

1021

1252

1041

N/A

3 Turns

Open

1075

1322

1111

N/A

2 Turns

Open

1128

1392

1181

N/A

1 Turns

Open

1183

1460

1251

N/A

Model No.

TSC072AD

TSC090AD

TSC102AD

TSC120AD

Closed

1235

N/A

1321

N/A

Factory set at 3 turns open

Table PD-20 — Sound Power Level - dB (ref. 10 ^-12Watts)

Unit

Octave Center Frequency

Overall

dBA

Model No.

TSC060AD

TSC072AD

TSC090AD

TSC102AD

TSC120AD

Note:

125

250

500

1000

2000

4000

8000

Tests follow ARI 270-95

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-21 — Static Pressure Drops Through Accessories - (Pascals)

Economizer

Electric Heater

OA/RA Dampers²

Accessory (kW)³

Unit

Model No.

TSC060AD

Airflow

(m³/h)

2720

3400

4080

3260

4080

4890

4080

5100

6120

4620

5780

6930

5440

6800

8160

Standard Pleated Filters

100% OA

100% RA

100% OA

100% RA

Filters¹

(50 mm)

Downflow

Horizontal

13-27

TSC072AD

TSC090AD

TSC102AD

TSC120AD

Notes:

1. Tested with standard filters. TheTSC060AD has 25 mm (1 inch) standard fiters. TheTSC072AD - 120AD has 50 mm (2 inch) standard filters.

The difference in pressure drop should be considered when utilizing optional 50 mm (2 inch) pleated filters.

2. OA = Outside Air and RA = Return Air

3. Nominal kW ratings at 415 V

Table PD-21a — Static Pressure Drops Through Accessories - (Inches of Water Column)

Economizer

Electric Heater

OA/RA Dampers²

Accessory (kW)³

Unit

Model No.

TSC060AD

Airflow

(CFM)

1600

2000

2400

1920

2400

2880

2400

3000

3600

2720

3400

4080

3200

4000

4800

Standard Pleated Filters

100% OA

100% RA

100% OA

100% RA

Filters¹

0.10

0.15

0.22

0.04

0.06

0.09

0.06

0.10

0.14

0.05

0.08

0.12

0.07

0.11

0.16

(2 inch)

0.15

0.22

0.29

0.07

0.09

0.12

0.09

0.13

0.18

0.08

0.11

0.16

0.10

0.15

0.20

Downflow

Horizontal

13-27

0.053

0.083

0.120

0.021

0.034

0.052

0.034

0.063

0.102

0.026

0.041

0.059

0.036

0.056

0.081

0.12

0.18

0.26

0.10

0.11

0.13

0.11

0.14

0.21

0.12

0.19

0.30

0.17

0.26

0.34

0.04

0.07

0.10

0.01

0.02

0.04

0.02

0.05

0.07

0.03

0.06

0.07

0.05

0.07

0.09

0.12

0.18

0.26

0.06

0.08

0.10

0.08

0.12

0.25

0.09

0.18

0.31

0.14

0.30

0.35

0.01

0.02

0.04

0.02

0.04

0.02

0.05

0.08

0.04

0.06

0.09

0.05

0.08

0.10

0.045

0.070

0.100

TSC072AD

TSC090AD

TSC102AD

TSC120AD

Notes:

0.042

0.070

0.106

1. Tested with standard filters. TheTSC060AD has 25 mm (1 inch) standard fiters. TheTSC072AD - 120AD has 50 mm (2 inch) standard filters.

The difference in pressure drop should be considered when utilizing optional 50 mm (2 inch) pleated filters.

2. OA = Outside Air and RA = Return Air

3. Nominal kW ratings at 415 V

Table PD-22 - Electric Heater Voltage Correction Factors (Apply to Auxiliary Electric Heat

Capacity)

Nominal

Voltage

Distribution

Voltage

380

Capacity

Multipiler

0.84

415

400

0.93

415

1.00

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-23 — Auxiliary Electric Heat Capacity (SI)

Total²

Stage 1

Stage 2

Unit

Model No.

Voltage

No. Stages

7.5 / 9.0

3.75 / 4.5

5.45 / 6.5

3.75 / 4.5

5.45 / 6.5

—-

5.6 / 6.7

11.3 / 13.5

—-

5.6 / 6.7

11.3 / 13.5

5.6 / 6.7

11.3 / 13.5

5.6 / 6.7

11.3 / 13.5

22.5 / 26.9

TSC060AD

TSC072AD

380-415/50/3

10.9 / 13.0

14.4 / 17.2

11.3 / 13.5

16.9 / 20.2

22.6 / 26.9

11.3 / 13.5

16.9 / 20.2

22.6 / 26.9

16.9 / 20.2

22.6 / 26.9

16.9 / 20.2

22.6 / 26.9

33.9 / 40.4

8.95 / 10.7

11.3 / 13.5

11.3 / 13.6

11.3 / 13.7

11.3 / 13.8

11.3 / 13.9

11.3 / 13.10

TSC090AD

TSC102AD

380-415/50/3

TSC120AD

380-415/50/3

Notes:

1. Does not include indoor fan power or heat

2. Heaters are rated at 380V / 415V. For other than rated voltage, CAP=(Voltage/Rated Voltage)²x Rated Cap.

Table PD-23A — Auxiliary Electric Heat Capacity (IP)

Total²

Stage 1

Stage 2

Unit

Model No.

Voltage

MBH

26 / 31

38 / 45

50 / 59

39 / 47

58 / 69

78 / 92

39 / 47

58 / 69

78 / 92

58 / 69

78 / 92

58 / 69

78 / 92

116 / 138

No. Stages

MBH

13 / 16

19 / 23

—-

20 / 23

39 / 47

—-

20 / 23

39 / 47

20 / 23

39 / 47

20 / 23

39 / 47

77 / 92

13 / 16

19 / 23

31 / 37

39 / 47

TSC060AD

TSC072AD

380-415/50/3

TSC090AD

TSC102AD

380-415/50/3

TSC120AD

380-415/50/3

Notes:

1. Does not include indoor fan power or heat

2. Heaters are rated at 380 / 415V. For other than rated voltage, CAP=(Voltage/Rated Voltage)²x Rated Cap.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance

Data

Table PD-24 — Air Temperature Rise Across Electric Heaters (Degrees C)

3400 m³/h

TSC060AD

6.6 / 7.9

9.6 / 11.4

—-

4100 m³/h

TSC072AD

—-

8.3 / 9.9

—-

12.4 / 14.8

16.5 / 19.7

—-

5100 m³/h

TSC090AD

—-

6.6 / 7.9

—-

9.9 / 11.8

13.2 / 15.7

—-

5800 m³/h

TSC102AD

—-

6800 m³/h

TSC120AD

—-

380V / 415V

07.5 / 09.0

10.9 / 13.0

11.3 / 13.5

14.4 / 17.2

16.9 / 20.2

22.6 / 26.9

33.8 / 40.4

Voltage

Stages

380-415/50/3

—-

12.6 / 15.1

—-

8.7 / 10.4

11.7 / 13.9

—-

7.4 / 8.9

9.9 / 11.8

14.8 / 17.7

—-

Note:

For minimum design airflow, see performance table for each unit.

To calculate temp rise at differrent airflow, use following formula:

Temp. Rise (C⁰) across Elect Htr = (kW x 2985)/( m³/h)

Table PD-24A — Air Temperature Rise Across Electric Heaters (Degrees F)

2000 CFM

TSC060AD

11.9 / 14.2

17.2 / 20.5

—-

2400 CFM

TSC072AD

—-

14.9 / 17.8

—-

22.3 / 26.6

29.8 / 35.4

—-

3000 CFM

TSC090AD

—-

11.9 / 14.2

—-

17.8 / 21.3

23.8 / 28.3

—-

3400 CFM

TSC102AD

—-

4000 CFM

TSC120AD

—-

380V / 415V

07.5 / 09.0

10.9 / 13.0

11.3 / 13.5

14.4 / 17.2

16.9 / 20.2

22.6 / 26.9

33.8 / 40.4

Voltage

Stages

380-415/50/3

—-

22.8 / 27.2

—-

15.7 / 18.8

21.0 / 25.0

—-

13.4 / 16.0

17.9 / 21.3

26.7 / 31.9

—-

Note:

For minimum design airflow, see performance table for each unit.

To calculate temp rise at differrent airflow, use following formula:

Temp. Rise (F⁰) across Elect Htr = (kW x 3414)/(1.08 x CFM)

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Zone Controls

Non-programmable manual auto

changeover with digital LCD Display —

Auto, heat, cool or off mode selection

button. Auto or off fan bottom. Status

indication LCD indicators — System on,

heat, cool, or service.

Zone Sensors

Conventional Thermostats

Zone Sensors are the building

occupant’s comfort control devices for

Precedent^™units with the ReliaTel

control. The zone sensor offering

operates with the Reliatel

Conventional Thermostats are the

building occupant’s comfort control

devises when a generic thermostat is

desired.

Manual

microprocessor

Changeover —

One Heat, One

Cool Thermostat.

Heat, Cool or Off

System Switch.

Fan Auto or On

Switch. Set Point

Dial. Adjustable

Heat Anticipator.

Manual Changeover — Heat, Cool or Off

System Switch. Fan Auto or Off Switch.

One

temperature

setpoint lever.

Automatic Changeover — One Heat,

Two CoolThermostat. Off, Auto System

Switch. Auto/On Fan Switch.

Programmable Night Setback — Auto

or manual changeover with seven-day

programming. Keyboard selection of

Heat, Cool, Fan, Auto, or On.

Manual/Automatic Changeover —Auto,

Heat, Cool or Off System Switch. Fan

Auto or Off

All programmable sensors have

Switch. Two

temperature

setpoint

levers. Optional

Status Indication

LED lights,

Programmable Electronic Night Setback

Thermostat — Heating setback and

cooling setup with 7-day, programming

capability. Available in two-stage

heating/cooling or one-stage heating/

cooling versions with automatic

changeover.

System On,

Heat, Cool, or

Service.

System On, Heat, Cool, Service LED/

indicators as standard. Night Setback

Sensors have one (1) Occupied, one (1)

Unoccuped, and two (2) Override

programs per day.

Integrated Comfort^™System —

Sensor(s) available with optional

temperature

Remote Sensor — Sensor(s) available

for all zone sensors to provide

remote sensing

capabilities.

adjustment and

override buttons

to provide

central control

through a Trane

Integrated

Comfort^™

system.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Electrical

Data

Table ED-1 — Unit Wiring

Standard Indoor Fan Motor

Oversized Indoor Fan Motor

Unit

Minimum

Maximum Fuse

Minimum

Maximum Fuse

Unit

Operating

Voltage Range

342-456

Circuit

Ampacitiy

17.7

23.2

24.8

Size Or Maximum

Circuit

Ampacitiy

17.7

24.2

26.5

Size Or Maximum

Model No.

TSC060AD

TSC072AD

TSC090AD

TSC102AD

TSC120AD

Circuit Breaker¹

342-456

26.8

31.2

28.5

31.2

Notes:

1. All units to be installed under local codes

Table ED-2 — Unit Wiring With Electric Heat Single Point Connection — 380-415 Volts

Standard Indoor Fan Motor

Oversized Indoor Fan Motor

Minimum

Circuit

Maximum Fuse

Minimum

Circuit

Maximum Fuse

Size Or Maximum

Circuit Breaker¹

25 / 25

Unit

Model No.

TSC060AD

Heater

Model No.

Heater²

MBH

Control

Stages

Size Or Maximum

Circuit Breaker¹

25 / 25

kW Rating

7.5 / 9.0

Ampacitiy

19.8 / 21.0

26.1 / 28.0

32.8 / 35.3

26.9 / 28.9

37.5 / 40.5

48.3 / 52.1

28.1 / 30.1

38.8 / 41.8

49.5 / 53.4

38.8 / 41.8

49.5 / 53.4

40.9 / 43.9

51.6 / 55.5

73.1 / 79.0

Ampacitiy

19.8 / 21.0

26.1 / 28.0

32.8 / 35.3

28.1 / 30.1

38.8 / 41.8

49.5 / 53.4

30.3 / 32.3

40.9 / 43.9

51.6 / 55.5

40.9 / 43.9

51.6 / 55.5

40.9 / 43.9

51.6 / 55.5

73.1 / 79.0

BAYHTRR412A

BAYHTRR418A

BAYHTRR423A

BAYHTRS418A

BAYHTRS427A

BAYHTRS436A

BAYHTRS418A

BAYHTRS427A

BAYHTRS436A

BAYHTRT427A

BAYHTRT436A

BAYHTRT427A

BAYHTRT436A

BAYHTRT454A

26 / 31

38 / 45

50 / 59

39 / 47

58 / 69

78 / 92

39 / 47

58 / 69

78 / 92

58 / 69

78 / 92

58 / 69

78 / 92

116 / 138

10.9 / 13.0

14.4 / 17.2

11.3 / 13.5

16.9 / 20.2

22.6 / 26.9

11.3 / 13.5

16.9 / 20.2

22.6 / 26.9

16.9 / 20.2

22.6 / 26.9

16.9 / 20.2

22.6 / 26.9

33.8 / 40.4

30 / 30

35 / 40

35 / 35

40 / 45

50 / 60

35 / 35

40 / 45

50 / 60

40 / 45

50 / 60

45 / 45

60 / 60

30 / 30

35 / 40

35 / 35

40 / 45

50 / 60

35 / 35

45 / 45

60 / 60

45 / 45

60 / 60

45 / 45

60 / 60

TSC072AD

TSC090AD

TSC102AD

TSC120AD

80 / 80

Notes:

1. All units to be installed under local codes

2. kW and MBH shown for 380V / 415V

Table ED-3 — Electrical Characteristics - Evaporator Fan Motor - 50 Hz

Standard Evaporator Fan Motor

Oversized Evaporator Fan Motor

Unit

Amps

Model No.

TSC060AD

TSC072AD

TSC090AD

TSC102AD

TSC120AD

No.

Volts

Phase

1.5

2.0

3.0

FLA

4.3

5.3

7.0

LRA

25.3

36.4

57.0

No.

Volts

380-415

Phase

2.0

3.0

FLA

5.3

7.0

LRA

36.4

57.0

380-415

Table ED-4 — Electrical Characteristics - Compressor Motor and Condenser Motor - 50 Hz

Compressor Motor

Condenser Fan Motor

Unit

Amps

Model No.

TSC060AD

TSC072AD

TSC090AD

TSC102AD

TSC120AD

No.

Volts

Phase

RPM

2875

RLA¹

9.5

12.7

13.20

9.3/6.9

9.9/8.5

LRA¹

74.00

95.00

100.00

No.

Phase

FLA

1.9

2.8

LRA

2.8

7.1

380-415

5.7

7.5

8.3

6.0/3.8

6.0/4.8

0.40

0.75

74.0/48.0

74.0/61.8

7.1

Note:

1. Comp1/Comp2

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Jobsite

Connections

Zone Sensors — Typical Number Of Wires

DISCONNECT

SWITCH

(BY OTHERS)

A — Manual Changeover . . . . . . . . . . . . . . . . . 4

Manual/Auto Changeover . . . . . . . . . . . . . 5

Manual/Auto Changeover with

ZONE SENSOR

OR THERMOSTAT

Status Indication LED’s . . . . . . . . . . . . . 10

Programmable Night Setback with

Status Indication LED’s . . . . . . . . . . . . . . 7

ROOFTOP

UNIT

Thermostats —Typical Number of Wires

A — 3 wires, 24-volts, Cooling Only

4 wires, 24-volts, with Electric Heat

B — 3 Power Wires + 1 Ground Wire (three phase)

2 Power Wires + 1 Ground Wire (single phase)

For specific wiring information, see the installation instructions.

All wiring except power wires is low voltage.

All customer supplied wiring to be copper and must conform to NEC or CEC and local electrical codes. Wiring shown dotted is to be furnished and installed by the customer.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensional

Data

TSC060

All dimensions are in inches/millimeters.

TSC060

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensional

Data

TSC060

All dimensions are in inches/millimeters.

TSC060 — Downflow Airflow Supply/Return

TSC060 — Horizontal Airflow Supply/Return

TSC060 — Unit Clearance and Roof Opening

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensional

Data

TSC060

All dimensions are in inches/millimeters.

TSC060 — Roof Curb

TSC060 — Downflow Duct Connections — Field Fabricated

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensional

Data

TSC072-120

All dimensions are in inches/millimeters.

TSC072-090

TSC102-120

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensional

Data

TSC072-120

All dimensions are in inches/millimeters.

TSC072-120 — Downflow Airflow Supply

and Return

TSC072-120 — Horizontal Airflow Supply

and Return

TSC072-120 — Unit Clearance and Roof

Opening

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensional

Data

TSC072-120

All dimensions are in inches/millimeters.

TSC072-120 — Roof Curb

TSC072-120 — Downflow Duct Connections —

Field Fabricated

ALL FLANGES 1 1/4” (31 MM)

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

TSC060

Options/Accessories

Dimensional

Data

All dimensions are in inches/millimeters.

TSC060 — Barometric Relief Damper Hood

TSC060 — Economizer , Manual or Motorized Fresh Air Damper

TSC060 — Swing Diameter for Hinged Doors Option

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

TSC072-120

Options/Accessories

Dimensional

Data

All dimensions are in inches/millimeters.

TSC072-120 — Economizer and Barometric

Relief Damper Hoods

TSC072-120 — Swing Diameter for

Hinged Door(s) Option

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Weights

Table W-1 - Maximum Unit and Corner Weights and Center of Gravity Dimensions (SI)

MaximumWeights⁽²⁾(kg)

Corner Weights⁽¹⁾(kg)

Center of Gravity (mm)

Unit

Model No.

TSC060AD

TSC072AD

TSC090AD

TSC102AD

TSC120AD

Shipping⁽²⁾

270

Net⁽²⁾

235

326

389

405

445

107

131

133

147

101

106

115

104

Length

790

970

990

Width

480

560

530

560

373

436

453

493

990

560

Notes:

(1) Corner weights are given for information only. All models must be supported continuously by a curb or equivalent frame support.

(2) Weights are approximate.

Table W-1a - Maximum Unit and Corner Weights and Center of Gravity Dimensions (IP)

MaximumWeights (lbs)

Corner Weights⁽¹⁾(lbs)

Center of Gravity (in)

Unit

Model No.

TSC060AD

TSC072AD

TSC090AD

TSC102AD

TSC120AD

Shipping⁽²⁾

595

823

962

998

1087

Net

518

718

857

893

982

Length

Width

165

235

289

294

323

124

182

222

233

253

105

128

148

159

178

124

173

197

207

229

Notes:

(1) Corner weights are given for information only. All models must be supported continuously by a curb or equivalent frame support.

(2) Weights are approximate.

Table W-2a - Accessory Net Weights^{(1) (2)}(lbs)

Table W-2 - Accessory Net Weights^{(1) (2)}(kg)

Net Weights⁽²⁾

TSC072-120

Accessory⁽³⁾

Economizer

TSC060

TSC072-120

Accessory⁽³⁾

TSC060

115

Economizer

Barometric Relief

Motorized Outside Air Damper

Manual Outside Air Damper

Roof Curb

Barometric Relief

Motorized Outside Air Damper

Manual Outside Air Damper

Roof Curb

Oversized Motor

Coil Guards

Oversized Motor

Coil Guards

Hinged Doors

Electric Heaters

Notes:

(1) Weights for options not listed are < 5 lbs.

(1) Weights for options not listed are < 3 kg.

2) Net weight should be added to unit weight when ordering factory-installed

accessories.

(3) Some accessories not available on all units.

(2) Net weight should be added to unit weight when ordering factory-installed

accessories.

(3) Some accessories not available on all units.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Mechanical

Specifications

General

UnitTop

Outdoor Fans

The units shall be convertible airflow.The

operating range shall be between 46°C

and -18°C (115°F and 0°F) in cooling as

standard from the factory for all units. All

units shall be factory assembled,

internally wired, fully charged with R-22,

and 100 percent run tested to check

cooling operation, fan and blower

rotation, and control sequence before

leaving the factory.Wiring internal to the

unit shall be colored and numbered for

simplified identification.

The top cover shall be one piece

construction or where seams exist, it

shall be double-hemmed and gasket-

sealed. The ribbed top adds extra

strength and prevents water from

pooling on unit top.

The outdoor fan shall be direct-drive,

statically and dynamically balanced,

draw-through in the vertical discharge

position. The fan motor shall be

permanently lubricated and shall have

built-in thermal overload protection.

Filters

Indoor Fan

One inch, throwaway filters shall be

standard on all 5 ton units.The filter rack

can be converted to two inch capability.

50 mm (2 inch) filters shall be factory

supplied on all 6-10 ton units. Optional 50

mm (2 inch) pleated filters shall be

available.

All units shall have belt drive motors.

Units with belt drive motors shall have

an adjustable idler-arm assembly for

quick-adjustment to fan belts and motor

sheaves. All motors shall be thermally

protected. Oversized motors shall be

available for high static operations.

Casing

Unit casing shall be constructed of zinc

coated, heavy gauge, galvanized steel.

Exterior surfaces shall be cleaned,

phosphatized, and finished with a

Compressors

Controls

All units shall have direct-drive, hermetic,

scroll type compressors with centrifugal

type oil pumps. Motor shall be suction

gas-cooled and shall have a voltage

utilization range of plus or minus 10

percent of unit nameplate voltage.

Internal overloads shall be provided with

the scroll compressors. Low and high

pressure switches shall be standard.

Unit shall be completely factory-wired

with necessary controls and contactor

pressure lugs or terminal block for

power wiring. Units shall have single

point power connection as standard.

Unit shall provide an external location

for mounting a fused disconnect device.

weather-resistant baked enamel finish.

Cabinet construction shall allow for all

maintenance on one side of the unit.

Service panels shall have lifting handles

and be removed and reinstalled by

removing only a single fastener while

providing a water and air tight seal. All

exposed vertical panels and top covers in

the indoor air section shall be insulated

with a cleanable foil-faced, fire-retardent

permanent, odorless glass fiber material.

The base of the unit shall be insulated

with 13 mm, 16 kg (1/2 inch, 1 pound)

density foil-faced, closed-cell material. All

insulation edges shall be either captured

or sealed.The unit’s base pan shall have

no penetrations within the perimeter of

the curb other than the raised 29 mm (1¹/8

inch high downflow supply/return

openings to provide an added water

integrity precaution, if the condensate

drain backs up.The base of the unit shall

have provisions for forklift and crane

lifting, with forklift capabilities on three

sides of the unit.

Microprocessor controls provide for all

24 volt control functions. The resident

control algorithms shall make all

heating, cooling, and/or ventilating

decisions in response to electronic

signals from sensors measuring indoor

and outdoor temperatures. The control

algorithm maintains accurate

temperature control, minimizes drift

from set point, and provides better

building comfort. A centralized

Microprocessor shall provide anti-short

cycle timing and time delay between

compressors to provide a higher level of

machine protection.

Refrigerant Circuits

Service pressure ports, and refrigerant

line filter driers are factory-installed as

standard. An area shall be provided for

replacement suction line driers.

Evaporator and Condenser Coils

Internally finned, 8 mm (⁵/16”) copper

tubes mechanically bonded to a

configured aluminum plate fin shall be

standard. Coils shall be leak tested at the

factory to ensure the pressure integrity.

The evaporator coil and condenser coil

shall be leak tested to 1375 kPa (200 psig)

and pressure tested to 3100 kPa (450

psig).The condenser coil shall have a

patent pending 1 + 1 + 1 hybrid coil

designed with slight gaps for ease of

cleaning. A removeable, reversible,

double-sloped condensate drain pan with

provision for through the base

condensate drain is standard.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Mechanical

Specifications

Economizer

Discharge Air Sensing

Accessories/Options

This accessory shall be either field or

factory-installed and shall be available

with or without barometric relief.The

assembly includes fully modulating 0-100

percent motor and dampers, minimum

position setting, preset linkage, wiring

harness with plug, spring return actuator

and fixed dry bulb control.The barometric

relief shall provide a pressure operated

damper that shall be gravity closing and

shall prohibit entrance of outside air

during the equipment “off” cycle.

Optional solid state or differential

enthalpy control shall be available for

either factory or field installation.The

factory-installed economizer arrives in

the shipping position and shall be moved

to the operating position by the installing

contractor.

This factory of field-installed option

provides true discharge air sensing in

heating models.This sensor is a status

indicator readable throughTracer^™or

Tracker^™.

Electric Heaters

Field-installed electric heat modules shall

be available for installation within basic

unit. Electric heater elements shall be

constructed of heavy-duty nickel

chromium elements internally delta

connected for 200 volt, wye connected

for 380-415 volt. Staging shall be

achieved through the unitary control

processor (UCP). Each heater package

shall have automatically reset high limit

control operating through heating

element contactors. All heaters shall be

individually fused from the factory, where

required. Power assemblies shall provide

single-point connection.

Oversized Motors

Factory or field-installed oversized

motors shall be available for high static

applications.

Clogged Filter/Fan Failure Switch

A dedicated differential pressure switch is

available, factory-installed, to achieve

active fan failure indication and/or

clogged filter indication.These indications

will be registered with either a zone

sensor with status indication lights or an

Integrated Comfort^™System.

Roof Curb

High Pressure Cutout

Standard on all units.

The roof curb shall be designed to mate

with the unit’s downflow supply and

return and provide support and a water

tight installation when installed properly.

The roof curb design shall allow field-

fabricated rectangular supply/return

ductwork to be connected directly to the

curb. Curb shall be shipped knocked down

for field assembly and shall include wood

nailer strips.

Phase Monitor

Phase monitor shall provide 100%

protection for motors and compressors

against problems caused by phase loss,

phase imbalance, and phase reversal.

Phase monitor is equipped with an LED

that provides an ON or FAULT indicator.

Hinged Access Doors

Sheet metal hinges are available factory-

installed on the Filter/Evaporator, Supply

Fan/Heat, and the Compressor/Control

Access Doors.

Black Epoxy Coated Condenser Coil

The coil provides corrosion protection to

condenser coils for seacoast application.

The protection is a factory-applied

thermoset vinyl coating, bonded to

normal aluminum fin stock.The uniform

thickness of the bonded vinyl layer

exhibits excellent corrosion protection.

Remote Potentiometer

The minimum position setting of the

economizer shall be adjusted with this

accessory.

Manual Outside Air Damper

Factory or field-installed rain hood and

screen shall provide up to 50 percent

outside air.

Motorized Outside Air Dampers

Factory or field-installed manually set

outdoor air dampers shall provide up to

50 percent outside air. Once set, outdoor

air dampers shall open to set position

when indoor fan starts.The damper shall

close to the full closed position when

indoor fan shuts down.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Mechanical

Specifications

Differential Pressure Switches

Control Options

Comm-3/4Trane Communication

Interface

This factory or field-installed option shall

be provided to interface microprocessor

controlled units with theTrane Integrated

Comfort^™systems.

These factory or field-installed sensors

allow individual fan failure and dirty filter

indication for microprocessor controlled

units.The fan failure switch will disable all

unit functions and “flash” the Service

LED on the zone sensor.The dirty filter

switch will light the Service LED on the

zone sensor and will allow continued unit

operation.

Comm-5 LonTalk Communication

Interface

This factory or field-installed option shall

be provided to allow the unit to

communicate as aTrane Comm-5 device

or directly with generic LonTalk Network

Building Automation System Controls.

Reference Enthalpy Control

Replaces the dry bulb control with a wet

bulb changeover controller which has a

fully adjustable set point. Enthalpy control

offers a higher level of comfort control,

along with energy savings potential, than

the standard dry bulb control.This is due

to the additional wet bulb sensing

Zone Sensor

This field-installed control shall be

provided to interface with the Micro

equipped units and shall be available in

either manual, automatic programmable

with night setback, with system

malfunction lights, or remote sensor

options.

capability.This option shall be available

for microprocessor controlled units. It can

be field-installed, or factory-installed with

the factory-installed economizer.

Differential Enthalpy Control

Thermostats

Replaces the standard dry bulb control

with two enthalpy sensors that compare

total heat content of the indoor air and

outdoor air to determine the most

efficient air source.This control option

offers the highest level of comfort control,

plus energy efficiency, available.This

option shall be available for

Two stage heating and cooling operation

or one stage heating and cooling shall be

available, for field installation, in either

manual or automatic changeover.

Automatic programmable electronic with

night set back shall also be available.

microprocessor controlled units. It can be

field-installed, or factory-installed with the

factory-installed economizer.

LowAmbient Cooling

All microprocessor units shall have

cooling capabilities down to 18°C (0°F) as

standard.

RT-PRC016-EN

Download from Www.Somanuals.com. All Manuals Search And Download.

Literature Order Number

File Number

RT-PRC016-EN

PL-UN-000-RT-PRC016-EN-02-04

PL-UN-000-RT-PRC016-EN-12-03

03-03Webb/Mason 02-04 Electronic Only

Supersedes

Trane

A business of American Standard Companies

www.trane.com

Stocking Location

Trane has a policy of continuous product and product data improvement and reserves the right to change

design and specifications without notice

For more information, contact your local district

office or e-mail us at [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Teac Stereo System MC DX80I User Manual
Toyota Automobile MCV10 User Manual
Transcend Information MP3 Player T sonic 310 User Manual
Triarch Indoor Furnishings 31082 32 User Manual
Tripp Lite Power Supply SUPDM16 User Manual
Tyco Network Card Escort5580TC User Manual
Uniden Cordless Telephone WDSS 5335 WDSS 5335 User Manual
Vista Home Security System N7227V5 User Manual
Vulcan Hart Fryer 1ER50A User Manual
Weber Charcoal Grill 120409 User Manual