32- 5038- 01
User’s Information Guide
TM
Trane CleanEffects Whole House Air Filtration System
TM
Congratulations – Your TRANE CleanEffects air filtration system is the most advanced,
innovative and effective whole house air filtration system on the market today. It is designed to
TM
deliver what we call TRANE Air throughout your home. It delivers air that is meticulously filtered
and cleaned of up to 99.98% of allergens to provide maximum comfort. You and your family can
breathe easier than ever before.
32-5038-01
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Information
SEQUENCE OF OPERATION
!
▲ CAUTION
You will need to turn off your air cleaner to
clean the filters. After cleaning, turn on the unit
by pressing and releasing the Power button.
The backlit Power and Filter Reset button will
illuminate along with first green LED indicating
power is present. When the indoor fan is oper-
ating the first green LED will slowly flash. This
indicates the field charger and collection cells
have power and the unit is operating normally.
There is a slight time delay between the indoor
fan starting and LED flashing.
This equipment should be inspected
frequently and collected dirt removed from it
regularly to prevent excessive accumulation
that may result in flashover or risk of fire.
The field charger should only be removed and
cleaned by authorized service personnel.
CLEANING INDICATORS
Both the pre-filter and the collection cells have
timers which monitor actual run time of the unit
and indicate when cleaning is required. The
time between cleaning can be adjusted based
on your preferences and conditions in the
home. See the SET-UP MODE section on
page 5 to change the filter timers.
NOTE: There is a 10 minute delay after the
indoor fan operates, before the air cleaner
starts to operate, each time the power to the
air cleaner is turned off/on. This can be
bypassed by going into and then out of the
Set-Up Mode.
The red PRE-FILTER light will illuminate when
it is time to clean the pre-filter.
Your air filtration system only operates when
the air is circulating through the indoor unit.
The air filtration system is most effective at
cleaning the air if the fan operates
continuously. Most thermostats have a setting
that will permit continuous fan operation.
Continuous fan mode during Cooling
The clean/dirty light bar indicator will
illuminate as the system cleans the air in your
home. The lights will progress from green to
yellow then to red. When the last red indicator
is flashing it is time to clean the collection
cells.
operation may not be appropriate in humid
climates. If the indoor air exceeds 60%
relative humidity or simply feels
REMOVING FILTERS FOR
CLEANING
uncomfortably humid, it is recommended that
the fan only be used in the AUTO mode.
In normal operation, the air cleaner may make
a slight sound as the air passes through it and
is cleaned. In some applications, you may
notice this sound coming from the return air
vent(s). If desired, this sound level can be
reduced with minimal impact on air cleaning
efficiency by reducing the power setting of the
♦ Turn the furnace/ air conditioning system off
at the thermostat.
!
▲ CAUTION
High voltage is present within the air cleaner
for operation. Before removing the door, turn
the power off and wait at least 15 seconds to
allow voltage to discharge.
field charger in the set-up mode (see p.5-6).
♦ Turn off power by pushing and holding the
power button for approximately three seconds
until all the LED’s illuminate. Release the
power button. The LED’s will remain on until
the voltage has discharged and it is safe to
remove the door.
MAINTENANCE
In normal use, the pre-filter should be cleaned
every 2 months and the collection cells should
be cleaned every 6 months. The field charger
should be cleaned only by a qualified service
This requires approximately 15 seconds. Do
technician annually.
32-5035-02
3
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Information
WASHING
not remove the door until all lights are off.
♦ Disconnect the power cable, if required,
and place the door in a secure location.
♦ Rotate the two latches and remove the
door.
Use low-pressure water spray, such as a sink
sprayer or garden hose to clean the cells.
Stubborn residue like tobacco smoke may
require warm water to be removed.
PRE-FILTER CLEANING:
The pre-filter can be vacuumed
(recommended) or washed clean.
Do NOT use soap or detergent in cleaning the
collection cells.
Do NOT immerse the cells completely in
water.
It is recommended the filter be vacuumed
outside the home to ensure particles on the
filter are not re-introduced into the air.
Persons highly sensitive to the collected
particles should wear appropriate respiratory
protection while cleaning the filter.
Do NOT place the cells into a dishwasher to
clean.
Slightly tap the collection cells to remove
water retained in the filter. Allow the collection
cells to dry completely before re-installing.
The pre-filter can be washed using low
pressure water spray, such as a sink sprayer
or garden hose. The pre-filter should be
completely dry before re-installing. Re-install
the pre-filter noting the airflow direction as
indicated on the filter.
Re-install the collection cells. With the handles
facing the front of the unit, align the slot on the
cell with the tab on the cabinet. Fold the
collection cell handles flat once installation is
complete.
NOTE: Do not replace the plastic pre-filter
with a metal type pre-filter. A metal pre-filter
will cause reduction in efficiency and
RE-INSTALLING THE POWER
DOOR
Install the door by positioning tabs inside of the
frame and rotating the door into place. Rotate
the two latches to secure the door. Plug in the
power cable if removed. Turn on power to the
unit by pressing and releasing the power
button.
potential failure of the system electronics.
COLLECTION CELL CLEANING
Remove both collection cells from the system
housing. The cells can be cleaned either by
vacuuming (recommended method) or by
washing.
NOTE: The first green LED will be on but will
not flash for the first 10 minutes the indoor fan
is operating. This is a drying cycle for the pre-
filter and collection cells.
VACUUM CLEANING
Using the wand attachment, vacuum both
sides of the collection cells until they are clean
RESET THE FILTER TIMERS
To reset the pre-filter timer, press and hold the
RESET button until the pre-filter LED turns off.
(1 to 2 seconds)
To reset the collection cell timer, press and
continue to hold the RESET button until the
collection cell LED’s turn off. (4 to 5 seconds)
It is recommended the filter be vacuumed
outside the home to ensure particles on the
filter are not re-introduced into the air.
Persons highly sensitive to the collected
particles should wear appropriate respiratory
protection while cleaning the filter.
32-5035-02
4
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Information
SET-UP MODE
You can customize the performance of the air
cleaner to meet the needs of your home and
family using the set-up mode.
Factory settings
To enter the set-up mode, press and hold
BOTH the Power and the filter RESET buttons
for a minimum of 5 seconds. The LED display
will light up indicating the current settings as
DIRTY
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
Field Charger Power
Maximum
shown in Figure 3 to the right.
Collection Cell
6 Months
You may select the cleaning intervals of the
pre-filter and the collection cells as well as the
power setting of the field charger by cycling
through the various settings (see page 6).
Once you have made the desired changes,
press and hold BOTH the Power and the filter
RESET buttons for a minimum of 5 seconds to
Pre-filter
2 Months
CLEAN
Fig. 3
exit the set-up mode.
Pre-Filter Timer Setting
The GREEN LED lights are used to set the pre-filter cleaning interval for one, two, or three
months. The number of illuminated GREEN LED lights indicates the current setting. The factory
setting is 2 months.
Collection Cell Timer Setting
The YELLOW LED lights are used to set the collection cells cleaning interval for two, four, six, or
nine months. The number of illuminated YELLOW LED lights indicates the current setting as
shown in Figure 5. The factory setting is 6 months.
Field Charger Power Level Setting
The RED LED lights are used to set the power level of the field charger for maximum, medium, or
minimum. The number of illuminated RED LED lights indicates the current setting as shown in
Figure 6. The factory setting is for maximum.
Lower settings will reduce the slight sound emitted by the unit with minimal loss of air cleaning
efficiency, if desired.
Lower settings will also further reduce the very low ozone produced by the air cleaner. The U.S.
Food and Drug Administration recommends indoor ozone concentrations should not exceed 50
parts per billion. Your air cleaner will contribute only 5 parts per billion at the factory setting and
can be reduced to 3 parts per billion at the minimum setting.
32-5035-02
5
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Information
CHANGING THE SETTINGS
While in the set-up mode, press the Power
button once to begin cycling through the
various setting options in the following order:
DIRTY
DIRTY
DIRTY
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
Pre-Filter Cleaning Interval Setting
(Figure 4)
One or more of the GREEN LED lights will
illuminate. To change the reminder interval
time, press the Reset button until the desired
setting is indicated, and then press the Power
button again.
CLEAN
CLEAN
CLEAN
One
Month
Two
Months *
Three
Months
Fig. 4
Collection Cells Cleaning Interval Setting
(Figure 5)
DIRTY
DIRTY
DIRTY
DIRTY
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
R3
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
One or more of the YELLOW LED lights will
illuminate. To change the reminder interval
time, press the Reset button until the desired
setting is indicated, and then press the Power
button again.
CLEAN
CLEAN
CLEAN
CLEAN
Two
Four
Six
Nine
Months Months
Months* Months
Fig. 5
DIRTY
DIRTY
DIRTY
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
Field Charger Power Level Setting
(Figure 6)
One or more of the RED LED lights will
illuminate. To change the power level setting,
press the Reset button until the desired setting
is indicated.
CLEAN
CLEAN
CLEAN
Minimum
Medium
Maximum*
To save your new settings and exit the set-up
mode, press and hold BOTH the Power and
filter RESET buttons for a minimum of 5
seconds.
Fig. 6
* Factory settings
32-5035-02
6
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Information
FAULT INDICATORS
DIRTY
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
The air cleaner has been designed to
continually monitor itself to insure it is working
properly. If it detects a problem, all four
YELLOW LED lights will flash continuously.
If this occurs, turn the unit off and clean both
the pre-filter and the collection cells to insure
no large material is trapped in the filters and
causing the fault.
CLEAN
DIRTY
R3
R2
R1
Y4
Y3
Y2
Y1
G3
G2
G1
If the unit detects any other type of fault, all
three RED LED lights will flash continuously.
The filter will shut down and does not
represent a safety risk. You should call a
qualified service technician for service.
CLEAN
32-5035-02
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
CleanEffects™ Whole
House Air Cleaner
TFD
(Parts Only)
This limited warranty is extended by American Standard Inc., to the original purchaser and to any succeeding owner of the
real property to which the CleanEffects™ Air Cleaner is originally affixed, and applies to products purchased and retained
for use within the U.S.A. and Canada.
If any part of your CleanEffects™ Air Cleaner fails because of a manufacturing defect within five years from the date of
the original purchase, Warrantor will furnish without charge the required replacement part. In addition, if the electronics fail
because of a manufacturing defect within the sixth through tenth year from the date of the original purchase, Warrantor
will furnish without charge the required replacement part. Any local transportation, related service labor, mechanical filters
and diagnosis calls are not included.
This limited warranty does not cover failure of your CleanEffects™ Air Cleaner if it is damaged while in your possession,
damage caused by unreasonable use of the CleanEffects™ Air Cleaner and/or damage from failure to properly maintain
the CleanEffects™ Air Cleaner as set forth in the Use and Care manual (see Proper Maintenance section).
THE LIMITED WARRANTY AND LIABILITY SET FORTH HEREIN ARE IN LIEU OF ALL OTHER
WARRANTIES AND LIABILITIES, WHETHER IN CONTRACT OR IN NEGLIGENCE, EXPRESS OR
IMPLIED, IN LAW OR IN FACT, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR USE, AND IN NO EVENT SHALL WARRANTOR BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow limitations on how long an implied limited warranty lasts or do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This limited
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Parts will be provided by our factory organization through an authorized service organization in your area listed in the
yellow pages. If you wish further help or information concerning this limited warranty, contact:
American Standard Inc.
Troup Highway
Tyler, TX 75711-9010
Attention: Manager, Field Operations Excellence
TW-391-4005
P.I.
Trane
Abusinessof
AmericanStandardCompanies
Trane has a policy of continuous product and product data improvement and it reserves the right to change
design and specifications without notice.
32-5038-01
Download from Www.Somanuals.com. All Manuals Search And Download.
|