SQPB
Video Cassette Recorder
W5 2 2 CG
OW NER’S MANUAL
AC68-02123L
W522CG ENG new(1-9)
1
2/20/04, 11:15
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to ship
your VCR. For maximum protection, repack the set as it was originally packed at the factory.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit.
Do not leave rubber or plastic products touching the unit for a long time. They will mar the
finish.
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the VCR is exposed to such a change in temperature, moisture may condense on the
cylinder inside, one of its most crucial internal parts. To prevent the VCR from possible
damage, do not use the unit for at least 2 hours when there is an extreme or sudden change
in temperature.
Compatibility
This video cassette recorder (VCR) is compatible with any other VCR bearing the
mark. HQ VHS equipment is also compatible with existing, non-HQ VHS equipment.
Copyright
It is permissible to record television programs, film, video tapes and other material only in
the event that third party copyrights and other rights are not violated.
®
As an ENERGY STAR Partner, TOSHIBA has determined that this product or
®
product model meets the ENERGY STAR guidelines for energy efficiency.
In the spaces provided below, record the Model and Serial No. located at the rear of your video
cassette recorder.
Model No.
Serial No.
Retain this information for future reference.
3
W522CG ENG new(1-9)
3
2/20/04, 11:15
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY
INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS
GIVEN IN THIS OWNER’S MANUAL AND THOSE MARKED ON THE UNIT.
RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can
result in electric shock or fire hazard. The safeguards incorporated in this unit will protect
you if you observe the following procedures for installation, use and servicing. This unit is
fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
ONLY.
1. Read owner’s manual
After unpacking this product, read the owner’s manual carefully, and follow all
the operating and other instructions.
2. Power Sources
This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your
home, consult your product dealer or local power company. For products
intended to operate from battery power, or other sources, refer to the operating
instructions.
3. Grounding or Polarization
This product may be equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
4. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure
reliable operation of the product and to protect it from overheating, and these
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface. This
productshouldnotbeplacedinabuilt-ininstallationsuchasabookcaseorrack
unless proper ventilation is provided or the manufacturer’s instructions have
been adhered to.
5. Heat
Theproductshouldbesituatedawayfromheatsourcessuchasradiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
4
W522CG ENG new(1-9)
4
2/20/04, 11:15
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Water and Moisture
Do not use this product near water - for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and
the like.
7. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
8. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit from
the product.
9. Overloading
Do not overload wall outlets; extension cords, or integral convenience recep-
tacles as this can result in a risk of fire or electric shock.
10. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system
is grounded so as to provide some protection against voltage surges and built-up static charges. Article
810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
S2898A
11. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
5
W522CG ENG new(1-9)
5
2/20/04, 11:15
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY
INSTRUCTIONS
12. Lightning
For added protection for this product during storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges.
13. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
14. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
15. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product. Any mounting of
the product should follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
S3125A
A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the product and cart
combination to overturn.
16. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to its normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance - this indicates a need for service.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
18. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
19. Safety Check
Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper
operating condition.
6
W522CG ENG new(1-9)
6
2/20/04, 11:15
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
IN TRO DUCTIO N
Variable Speed Playback ................. 20
Provides important notes and general
explanation of the VCR, including names of the
buttons, jacks, etc.
• Picture Search
• Commercial Movie Skip
• Still Picture
• Frame Advance
• Slow-motion Picture
SAFETY PRECAUTIONS .................... 2
IMPORTANT PRECAUTIONS ............. 3
IMPORTANT SAFETY
INSTRUCTIONS................................... 4
Useful Functions in Tape
Operation........................................... 22
Contents .............................................. 7
Identification of Controls ................... 8
• Front Panel
• Remote Control
• VCR Display
• Rear Panel
• Counter Function
• Tape Remaining Time
• Memory Stop Feature (Zero Return)
RECO RDIN G
Explains recording functions.
Recording a TV Program.................. 24
PREPARATIO N
• Basic Recording
• Watching a TV program while
recording another
Explains what you need to do before operating
the VCR.
• Skipping unnecessary scenes while
recording
• Recording off time setting
Timer Program Recording ............... 25
MTS Broadcast Compatibility .......... 28
How to Use the Remote Control ...... 10
Connections ...................................... 11
Auto Set Up ....................................... 13
Initial Settings Using On-screen
Display ............................................... 14
ADDITIO N AL IN FO RMATIO N
• Setting the Language
• Setting the VCR output channel
• Optional settings on the SETUP
screen
• Setting the Clock
Storing Channels on the VCR.......... 16
Video Cassette Use .......................... 18
Remote Control
for TOSHIBA TVs .............................. 29
Before Calling Service Personnel ... 30
Specifications ................................... 31
Accessories ...................................... 31
LIMITED WARRANTY............. Back cover
PLAYBACK
Explains variable functions concerning
playback.
Playback ............................................ 19
• Basic Playback
• Double Speed Playback
• S-VHS Quasi Playback (SQPB)
7
W522CG ENG new(1-9)
7
2/20/04, 11:15
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Identification of Controls
See the page in
for details.
This manual shows the names of buttons in italics.
Fro n t Pa n e l
REC
EJECT
POWER
Cassette Compartement
14
24
18
19 19 19 19
24
LINE IN AUDIO
( L/MONO, R) jaks
REW
PLAY
FF
STOP
CHANNEL
Remote
sensor
VCR Display
LINE IN VIDEO jack
Re m o te Co n tro l
To operate your TV.
TV 29
VCR
TV
POWER
14
To operate this VCR.
POWER
CH/TRK
VCR
14
19
1
4
2
5
8
0
3
6
Number
buttons
17
28
TV/VCR
24
20
17
CM SKIP
7
A.SELECT
9
CM SKIP
A.SELECT
100
100
19
PLAY *
EJECT
REW *
14 ENTER
EJECT
PLAY *
19
18
19
PLAY
FF *
19
REW
FF
ENTER
19 STOP *
STOP
21
22
PAUSE/STILL
SLOW
20
24
22
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
DISPLAY
REMAIN/
COUNT
RESET
SP/SLP
REMAIN/COUNTER 22
I.SELECT 24
COUNT RESET
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
26
27
TIMER
REC 24
CANCEL
29
TV VOL
14 PROG.
* These buttons are used to control the
cursor on the screen.
8
W522CG ENG new(1-9)
8
2/20/04, 11:15
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR Disp la y
Cassette indicator
Timer recording indicator
TIMER
Hi-Fi
VCR
Hi-Fi indicator
VCR indicator
Multifunctional
indicator
Re a r Pa n e l
LINE OUT AUDIO jack (L,R)
RF IN (FROM ANT.) terminal
LINE
OUT
IN
(FROM ANT.)
R
AUDIO
L
RF
OUT
(TO TV)
VIDEO
TO Wall outlet
LINE OUT VIDEO jack
RF OUT (TO TV) terminal
LINE IN Front jacks
If the connected equipment is monaural (has one audio output jack), connect the L (MONO) side, the same
sound is recorded on both L and R on the Hi-Fi track.
9
W522CG ENG new(1-9)
9
2/20/04, 11:15
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
How to Use the Remote Control
This section explains how to get ready for remote control operation.
Se ttin g u p th e Re m o te Co n tro l
Open the battery compartment lid on the
rear panel.
1
Install 2 batteries (“AA” size) following
the polarity diagrams.
2
3
4
Close the battery compartment lid.
+
+
Point the remote control at the VCR and press the buttons within the operating range.
Distance: within about 7 m from the front of the remote sensor
Angles: within about 30˚ in every direction
N o te s o n b a tte rie s
Ca rin g fo r th e re m o te co n tro l
• The life of the batteries is about 1 year
depending on the conditions of use.
• If the remote control does not operate correctly,
replace all batteries with new ones.
• Do not expose the remote sensor of the VCR
to a strong light source such as direct sunlight
or illumination (especially high-frequency
lighting) when using the remote control.
• Be careful not to spill water on the remote
control or to place it on anything wet, and avoid
sharp impacts.
• If the remote control is not to be used for a
long period of time, remove the batteries to
avoid possible damage from battery corrosion.
10
W522CG ENG new (10-19)
10
2/20/04, 11:16
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Connections
Before you use this VCR, it is necessary to connect it to your TV. Several ways of connecting are
available depending on your use of TV or cable box. Select one which is applicable to your equipment.
An te n n a / VCR/ TV Co n n e ctio n
Disconnect the antenna cable from your TV and connect it to the RF IN terminal on the
VCR.
1
Connect the RF OUT terminal to the TV.
2
UHF antenna
only
VHF antenna
only
VHF/UHFcombination
antenna
IN
(FROM ANT.)
LINE
1
2
OUT
IN
(FROM ANT.)
R
AUDIO
L
RF
OUT
(TO TV)
VIDEO
RF
VHF/UHF
OUT
(TO TV)
VHF UHF
Antenna splitter
(not supplied)
AUDIO / VIDEO Co n n e ctio n s
The AUDIO/VIDEO jacks are also available to connect your TV.
W h e n co n n e cte d y o u r TV u sin g th e
AUDIO / VIDEO O UT ja ck s
LINE
OUT
IN
(FROM ANT.)
R
AUDIO
L
RF
OUT
(TO TV)
To watch video pictures, set the video input mode
on your TV. For the video input mode, refer to the
manual of your TV.
VIDEO
LINE OUT VIDEO
VIDEO IN
LINE OUT AUDIO AUDIO IN
Ca b le Co n n e ctio n
Choose one of the below according to your usage of the cable box.
Th is se t-u p w ill e n a b le y o u to :
– record an unscrambled channel.
– watch an unscrambled channel while recording it.
LINE
OUT
IN
(FROM ANT.)
R
– record an unscrambled channel while watching
another (only when you connect a cable-
compatible TV).
AUDIO
L
OUT
(TO TV)
VIDEO
Yo u w ill n e e d to :
• select TV channel 3 or 4 to receive video signals.
(See page 14)
• to record a channel while watching another, press
Incoming cable
.
TV/VCR on the remote control to turn off the
“VCR” indicator in the VCR display and select a
desired channel on the TV (only when you connect
a cable-compatible TV)
11
W522CG ENG new (10-19)
11
2/20/04, 11:16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (continued)
Th is se t-u p w ill e n a b le y o u to :
– record an unscrambled channel.
– watch an unscrambled channel while recording it.
LINE
OUT
IN
(FROM ANT.)
R
AUDIO
L
OUT
(TO TV)
VIDEO
– record an unscrambled channel while watching
another (scrambled or unscrambled).
Cable box
Yo u w ill n e e d to :
Incoming cable
• set TV channel to the output channel of the cable
box.
IN
OUT
turn on the cable box and select cable channel 3
or 4 according to the output channel of the VCR.
•
• to record a channel while watching another, press
TV/VCR on the remote control to turn off the
“VCR” indicator in the VCR display and select a
desired cable channel on the cable box.
Th is se t-u p w ill e n a b le y o u to :
LINE
OUT
IN
(FROM ANT.)
R
AUDIO
L
– watch an unscrambled or scrambled channel
RF
OUT
(TO TV)
VIDEO
while recording it.
– record any channels through the cable box.
Cable box
Yo u w ill n e e d to :
• set TV channel 3 or 4 to receive video signal.
(See page 14. )
IN
OUT
Incoming cable
• set VCR channel to the output channel of the
cable box, and select a desired cable channel on
the cable box.
• while the VCR is turned off or the “VCR” indicator
is not lit in the VCR display, set TV channel to the
output channel of the cable box.
A
A/B switch
Cable box
Th is se t-u p w ill e n a b le y o u to :
A
B
– watch an unscrambled or scrambled channel
while recording it.
– record an unscrambled channel while watching
another unscrambled channel (only when you
connect a cable-compatible TV).
B
LINE
OUT
IN
(FRONT.)
R
AUDIO
L
RF
OUT
(TO TV)
VIDEO
• A/B switch “A”: record and watch an unscrambled
channel which comes bypassing
the cable box.
• A/B switch “B”: record and watch a scrambled or
unscrambled channel coming
through the cable box.
Th is se t-u p w ill e n a b le y o u to :
Cable box
Front AV
– watch or record a channel through the cable box
via the LINE IN (AUDIO/VIDEO) jacks.
LINE
OUT
IN
(FROM ANT.)
R
AUDIO
L
RF
OUT
VIDEO
(TO TV)
Yo u w ill n e e d to :
• press I.SELECT so that the VCR display shows
“L”.
12
W522CG ENG new (10-19)
12
2/20/04, 11:16
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Auto Set Up
The VCR’s clock and tuner channels are set automatically when the VCR is plugged into the AC outlet.
Au to Se t u p
Plug the VCR into the AC outlet
1
VCR
TV
POWER
“Auto” blink while the VCR automatically sets the clock using
the data broadcast by the local TV stations.
While “Auto” is blinking, channel memory is also set
automatically.
2
1
4
2
5
8
0
3
6
CM SKIP
7
A.SELECT
9
100
EJECT
PLAY
REW
FF
ENTER
STOP
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
CANCEL
When Auto set up has been completed, the VCR is on
standby mode.
3
Notes
• It may takes several minutes during the Auto set-up
• Press CANCEL on the remote control to cancel the auto set-up.
13
W522CG ENG new (10-19)
13
2/20/04, 11:16
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Initial Settings Using On-screen Display
The language selection and clock setting must be set first when VCR is first plugged in or after it
encounters a power failure.
Preparation
• Turn on the TV, and select the video channel (3 or 4), or the video input mode if you made the Audio/Video
connection (page 11).
• Press VCR to set the remote control operating the VCR.
Se ttin g th e La n g u a g e
VCR
VCR
TV
POWER
POWER
Press POWER to turn on the VCR.
1
2
1
4
2
5
8
0
3
6
CM SKIP
Press PROG..
The following screen appears on the TV.
7
A.SELECT
9
100
REW
EJECT
PLAY
FF
REW
FF
ENTER
PLAY, STOP
STOP
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
ENTER
PROG.
I.SELECT
REC
TIMER
Select the language using PLAY or
STOP and press PROG..
The screen turns to the MENU screen.
3
4
PROG. CANCEL
TV VOL
Press PROG. to return to the normal TV screen.
Se ttin g th e VCR O u tp u t Ch a n n e l
Press PROG..
1
Select SET UP using FF or REW and press ENTER.
2
3
Select the VCR OUTPUT using PLAY or STOP and set VCR
output channel using FF or REW.
Press PROG. to exit.
A message will appear indicating the VCR output channel is changed.
4
O p tio n a l se ttin g s o n th e SET UP scre e n
Other optional settings can be made. Press ENTER while “SET UP” is
selected on the MENU screen. The screen turns to the SET UP screen.
Page 14
Page 22
Page 28
Page 23
To change the language, move down here and set to the desired one.
To exit, press PROG. once.
14
W522CG ENG new (10-19)
14
2/20/04, 11:16
Download from Www.Somanuals.com. All Manuals Search And Download.
Se ttin g th e Clo ck
Press ENTER to start the “AUTO” clock
set feature.
After the VCR is turned off, it automatically
updates the clock using the data broadcast
by the local TV stations.
8
9
Example: To set the clock to 2:30 p.m. on
August 25 (summer time) 2004
Press PROG..
The MENU screen appears on the TV.
1
*The clock is
revised by
Select “PRESET” using FF or REW, and
press ENTER.
2
broadcasting
signal at 8:00 A.M
every morning.
Select the options using FF or REW.
Change the data using PLAY or STOP.
1) Set “SUMMER TIME
(Daylight-Saving Time)”.
Press ENTER to select “CLOCK SET”.
3
DST start: Daylight-saving time begins on
the first Sunday in April. Because the
clock automatically changes from 2:00 AM
to 3:00 AM (forward one hour).
DST end: Daylight-saving time ends on
the last Sunday in October. The VCR
clock automatically changes from 2:00 AM
to 1:00 AM (back one hour).
Remember that any part of a scheduled
Timer Recording that falls between these
two times will not be recorded.
AUTO: the VCR is using the clock data
Broadcast by the local TV stations.
IN: You want to use the DST function, and
you are living in the area that apply
Daylight-saving time.
OUT: You are not living in the area that
apply Daylight-saving time and you do not
Select “AUTO” or “MANU” using PLAY or
STOP.
AUTO: The VCR automatically sets or adjusts
the clock.
If you select “AUTO” mode, proceed to step 8.
MANU: You can set the clock manually.
If you select “MANU” mode. Select “ SUMMER
TIME “ using FF Set to “IN“ or “OUT“ for the
SUMMER (daylight saving ) time using PLAY or
stop.(For “IN” and “OUT” selections, see the
4
want to use DST function.
2) Set “TIME ZONE”.
If you select “AUTO” for your time zone,
the VCR sets the clock using the first
Coordinated Universal Time information it
finds. If the time is not correct, select
another time zone or use the “MANU”
option.
5 Move to the next using FF
(To move back,press Rew.)
6 Vary the digits to set the hour.
3) Set “CLOCK DATA CH”.
PLAY : To increase.
STOP : To decrease.
If you don't know the clock data channel,
select “AUTO”. The VCR will scan
automatically to tune the channel carrying
the clock data.
7 Repeat step 5 and 6 to set the minutes,
If AUTO CLOCK SET is unsuccessful, set the
time and date through the “MANU” clock
set menu selection.
month, day , and the year (by the last
two digits).
Proceed to step 10 to start the clock.
Press PROG..
Now the clock starts.
10
15
W522CG ENG new (10-19)
15
2/20/04, 11:16
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Storing Channels on the VCR
This section is required if you receive only normal TV or unscrambled cable channels.
In co m in g An te n n a / Ca b le (CATV) Sig n a ls
The VCR scans through all receivable TV and CATV channels and stores only the active
ones in your area into the memory. Once the storing is finished, you can select a desired
channel using CH/TRK.
Preparation
• Turn on the TV, and select the video channel (3 or 4) or the video input mode if you made the Audio/Video
connection (page 11).
• Press I.SELECT so that the channel number will appear if “L” is displayed in the VCR display.
In co m in g An te n n a / Ca b le (CATV) Sig n a ls
Press PROG. to display the MENU screen.
1
VCR
TV
POWER
Select “PRESET” using FF or REW,
and press ENTER.
1
4
2
5
8
0
3
6
2
Number
buttons
CM SKIP
7
A.SELECT
9
100
100
REW
EJECT
PLAY
FF
REW
FF
ENTER
PLAY, STOP
STOP
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
ENTER
Select “CH MEMORY” using PLAY
or STOP, and press ENTER.
3
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
1,6
I.SELECT
Set “TV/CATV“ to “TV” or “CATV” using FF or REW.
TV: To store channels received via the antenna.
CATV: To store channels received via the incoming cable.
4
5
Select “AUTO SCAN” using PLAY or
STOP, and press FF to set to “ON”.
The VCR starts scanning and the
channels are stored in the VCR in
ascending order. When the scanning is
finished, the screen automatically
returns.
Press PROG.twice to exit.
6
16
W522CG ENG new (10-19)
16
2/20/04, 11:17
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Enter a channel number of 1 to 125 using
number buttons.
For more than 100 number, first press 100.
For CATV channels, refer to the chart below.
(For other orders, check with your cable
company.)
4) Repeat steps 2) and 3) to add or erase
channels as necessary.
Ad d in g o r e ra sin g ch a n n e ls
Adding channels
If a desired channel cannot be scanned
automatically because of a weak signal, it can be
added to the memory.
Erasing channels
You can erase a stored channel from the memory
if it is unnecessary.
5) Press PROG. two times to exit.
1) Follow steps 1 to 3 of “Incoming Antenna/
CATV Signals”.
2) Select “ADD CH” or “ERASE CH” using PLAY
or STOP.
Se le ctin g sto re d ch a n n e ls
Once the active channels have been stored, you
can select the channels in two ways below.
Number buttons
To add channels
To enter digits of the channel number.
• For one-digit number, enter 0 before.
• For more than 100 number, first press 100.
• Each number button needs to be pressed
within 2 seconds.
CH/TRK buttons
To shift up or down the stored channel numbers.
To erase channels
Ch a n n e l re fe re n ce ch a rt
CH NUMBER
TV
CATV STD (HRC/IRC)
1
–
1(A-8)
2
2
2
3
3
3
4
4
4
5
5
6
6
7
7
7
8
8
8
9
9
9
Number on the VCR
Corresponding channel number
5(A-7) 6(A-6)
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
10 11 12 13
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
R
S
T
U
V
W
AA BB CC DD EE FF GG HH II
JJ KK LL MM NN OO
…
…
…
52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71
52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69
PP QQ RR SS TT UU VV WW XX YY ZZ AAA BBB 65 66 67 68 69 70 71
–
–
…
…
…
93 94 95 96 97 98 99 100 101 102 103
121 122 123 124 125
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
93 94 A-5 A-4 A-3 A-2 A-1 100 101 102 103
121 122 123 124 125
CATV signals
• STD (standard) cable TV signals
• HRC (Harmonic Related Carriers) cable TV signals
• IRC (Incremental Related Carriers) cable TV signals
IRC is also called ICC (Incremental Coherent Carriers)
17
W522CG ENG new (10-19)
17
2/20/04, 11:17
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Video Cassette Use
Vid e o Ca sse tte Use
Lo a d in g a ca sse tte
Push the cassette into the cassette compartment with the window side facing up and the
label side towards the front. The VCR is automatically turned on. The
appear in the VCR display.
indicator will
Eje ctin g a ca sse tte
Press EJECT. The cassette is ejected from the cassette compartment.
Warning
Do not insert your hands or any foreign objects into the compartment. This may result
in injury or damage. Take special care with children to avoid accidents.
Pre ca u tio n s w h e n u sin g vid e o ca sse tte s
Video cassettes have a safety tab to prevent accidental erasure. If the tab has already been removed,
recording cannot be performed.
To prevent accidental erasure
To record again
Remove this safety tab with a screwdriver.
Cover the tab hole with adhesive tape.
• Avoid exposing cassettes to direct sunlight. Keep them away from heaters.
Avoid extreme humidity, vibrations or shock, strong magnetic fields (near a motor, transformer or
magnet) and dusty place.
18
W522CG ENG new (10-19)
18
2/20/04, 11:17
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Playback
This section explains the basic playback operation.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• Press VCR to set the remote control operating the VCR.
Ba sic Pla y b a ck
Load a recorded cassette.
Power is turned on.
If the cassette has no safety tab,
playback starts automatically.
1
TIMER
REC
VCR
TV
POWER
S
L
P
S
L
VCR
1
4
2
5
8
0
3
6
CH/TRK
CM SKIP
7
A.SELECT
9
100
Press PLAY to start playback.
2
3
ST
2
EJECT
L
VCR
VCR
PLAY
FF
REW
FF
ENTER
STOP
To stop playback, press STOP.
3
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
I.SELECT
REC
TIMER
REW
PROG. CANCEL
TV VOL
Do u b le Sp e e d Pla y b a ck
Press PLAY during playback.
A tape runs at double speed
playback.
1
To resume normal playback Press PLAY.
Re w in d in g / Fa st-fo rw a rd in g
Press REW or FF in the stop mode.
Ad ju stin g th e tra ck in g
When playback starts, the VCR automatically adjusts the tracking for clear pictures and sound
(Digital Auto Tracking).
If the VCR cannot locate the best possible tracking point, hold down one of CH/TRK to adjust the
tracking manually.
Notes
• During the adjusting, the playback picture and sound may be distorted.
• The digital auto tracking is activated only in the playback mode.
• The noise on the screen may not be completely eliminated depending on the tape used, especially when the
tape was recorded on another VCR.
S-VHS Q u a si Pla y b a ck (SQ PB)
• This VCR can also play back at tape which is recorded in S-VHS format.
But the playback pictures does not have the same quality and resolution as the original S-VHS
playback picture.
• This VCR cannot record in S-VHS format.
• SQPB is an abbreviation for S-VHS Quasi Playback.
19
W522CG ENG new (10-19)
19
2/20/04, 11:17
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Variable Speed Playback
You can play back a tape at various tape speeds.
Pictu re Se a rch
A tape runs at 5 times or 7 times the normal playback speed so
that you can quickly locate a particular scene.
VCR
TV
POWER
1
4
2
5
8
0
3
6
CM SKIP
Press FF or REW during playback.
The tape runs at 5 times the normal playback speed.
1
CM SKIP
PLAY
7
A.SELECT
9
100
EJECT
To change the tape speed to 7 times the normal playback
speed, press and hold FF or REW.
2
PLAY
REW
FF
FF
REW
ENTER
If you release it, the tape speed returns to 5 times.
STOP
PAUSE/STILL
SLOW
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
Note
I.SELECT
REC
TIMER
If you press FF or REW during picture search, the mode changes to fast-
forwarding or rewinding.
PROG. CANCEL
TV VOL
To re su m e n o rm a l p la y b a ck
Press PLAY.
Co m m e rcia l Mo vie Sk ip
You can skip a portion of playback you do not want ( such as a
commercial ) and then return to normal playback.
Press CM SKIP during playback.
1
The VCR will automatically search forward for 30 seconds
to a maximum of 3 minutes ( six presses ) and then
resume normal playback.
Still Pictu re
A picture freezes so that you can watch closer.
Press PAUSE/STILL during playback.
The picture freezes.
1
To re su m e n o rm a l p la y b a ck
Press PAUSE/STILL again.
Notes
• The still mode is automatically cancelled after about 5 minutes and returns
to normal playback.
• The still picture may shake if a picture of a fast-moving object or scene is
frozen. This is not a defect in the unit.
Ad ju stin g Still Pictu re Sta b ility
If the still picture is distorted or flickers, hold down one of CH/TRK until
the picture becomes stable.
Note
The distortion of the still picture may not be eliminated completely.
20
W522CG ENG new(20-23)
20
2/20/04, 11:18
Download from Www.Somanuals.com. All Manuals Search And Download.
Fra m e Ad va n ce
A picture advances frame by frame.
VCR
TV
POWER
1
4
2
5
8
0
3
6
Press PLAY during still playback.
Each time you press PLAY, the picture advances one frame.
CH/TRK
1
CM SKIP
7
A.SELECT
9
100
PLAY
To re su m e n o rm a l p la y b a ck
EJECT
PLAY
Press PAUSE/STILL.
REW
FF
ENTER
STOP
PAUSE/STILL
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
Slo w -m o tio n Pictu re
I.SELECT
REC
TIMER
The tape runs at 1/7th or 1/15th the normal playback speed.
PROG. CANCEL
TV VOL
SLOW
Press SLOW during playback.
The tape runs at about 1/7th the normal playback speed.
1
Each time you press SLOW, the speed alternates between 1/7th and
1/15th.
To re su m e n o rm a l p la y b a ck
Press PLAY.
Notes
• The slow-motion picture mode is automatically cancelled after about 5
minutes and returns to normal playback.
• The slow-motion picture may flicker up and down. This is not a defect in the
unit.
Ad ju stin g th e Tra ck in g Ma n u a lly
If the slow-motion picture is noisy, hold down one of CH/TRK until the
best picture is obtained.
Note
The noise in the slow-motion picture may not be eliminated completely.
21
W522CG ENG new(20-23)
21
2/20/04, 11:18
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Useful Functions in Tape Operation
These functions will help your playback.
Co u n te r Fu n ctio n
You can view the clock, linear time counter or tape remaining
time in the VCR display or on the TV screen.
VCR
TV
POWER
1
4
2
5
8
0
3
6
Each time you press REMAIN/COUNTER, the VCR display
changes in sequence as follows:
CM SKIP
7
A.SELECT
9
100
ENTER
→ Linear time counter → Tape remaining time (R) → Clock
EJECT
PLAY
PLAY
FF
REW
FF
REW
ENTER
The indication above will also appear on the TV screen by pressing
DISPLAY. They are switchable with REMAIN/COUNTER.
STOP
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
STOP
I.SELECT
REC
TIMER
To re se t th e lin e a r tim e co u n te r to “ 0 :0 0 :0 0 ”
COUNT RESET
PROG.
PROG. CANCEL
TV VOL
The counter is automatically reset to “0:00:00” when a cassette is
ejected. If you want to reset at another point, such as the beginning of
a new recording, just press COUNT RESET.
REMAIN/
COUNTER
Notes
DISPLAY
• The linear time counter does not work on non-recorded portions on the
tape.
• When the tape is ejected or the VCR is turned off, the display changes to
clock.
• If the tape rewinds back over “00:00”, “–” appears in the VCR display.
• The displayed time of the linear time counter is only an approximation.
Ta p e Re m a in in g Tim e
To view the tape remaining time in the VCR display, select the
tape length beforehand.
Turn on the VCR and load a cassette.
1
Press PROG. to display the MENU screen.
2
Select “SET UP” using FF or REW, and press ENTER.
3
Select the length of the tape, using
FF or REW.
4
T120: for a T-120 tape or shorter
T160: for a T-140 or T-160 tape
T180: for a T-180 tape
Press PROG. to exit.
5
Press REMAIN/COUNTER.
The remaining time (“R - : - -”) appears in the VCR display.
6
Notes
• The displayed remaining time is an approximation.
• The remaining time is calculated according to the tape speed (SP or SLP)
and the cassette type.
22
W522CG ENG new(20-23)
22
2/20/04, 11:18
Download from Www.Somanuals.com. All Manuals Search And Download.
Me m o ry Sto p Fe a tu re (Ze ro Re tu rn )
On the SET UP screen, select
1
“COUNTER MEM.” using PLAY or
STOP, and set to “ON” using
REW or FF.
VCR
TV
POWER
1
4
2
5
8
0
3
6
CM SKIP
7
A.SELECT
9
100
ENTER
EJECT
PLAY
PLAY
FF
REW
FF
REW
Press PROG. to exit.
ENTER
2
STOP
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
The memory-stop feature allows you to quickly return to a
counter reading of “0H00M00S” from any point on the tape.
Memory stop is automatically turned on whenever the time
counter with memory is displayed on the TV screen. This is
convenient when you want to watch a segment of the tape
repeatedly. You may also discover other useful application
for this feature.
REMAIN/
COUNT
RESET
STOP
I.SELECT
REC
TIMER
COUNT RESET
PROG.
PROG. CANCEL
TV VOL
REMAIN/
COUNTER
DISPLAY
Notes: If you are rewinding the tape and the VCR stops at
“0H00M00S M”, press REW again to continue
rewinding.
If you press the FF (fast-forward) button and the
time counter never reaches “0H00M00S M” between
that point and the end of the tape, the VCR will
continue to fastforward to the end of the tape.
23
W522CG ENG new(20-23)
23
2/20/04, 11:18
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Recording a TV Program
This section explains the basic recording operation.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
Ba sic Re co rd in g
VCR
TV
POWER
Load a cassette with the safety tab attached.
1
2
1
4
2
5
8
0
3
6
Press TV/VCR so that the “VCR”
3
2
CM SKIP
7
A.SELECT
9
indicator appears in the VCR display.
VCR
100
EJECT
PLAY
Select a channel to record with
3
REW
FF
ENTER
CHANNEL on the VCR, or CH/TRK
VCR
STOP
or number buttons on the remote
control.
• If you record cable channels via the cable box, make the output
channel number of the cable box or “L” appear, depending on your
connection. (See pages 11– 12.)
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
6
4
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
5
I.SELECT
Press SP/SLP to select the
recording tape speed.
SP: Suitable for general recording with
4
TIMER
REC
VCR
better picture and sound quality.
SLP: Suitable for tripling recording time, but with less picture and
sound quality than using the SP tape speed.
To record from other
connected equipment
In step 3, press I.SELECT to
switch the display as follows:
L : To record via the LINE IN
jacks on the front panel.
REC
TIMER
Press REC on the VCR, or
simultaneously press both REC on
the remote control.
5
6
TIMER
S
L
VCR
Recording starts.
Press STOP to stop recording.
Wa tch in g a TV p ro g ra m w h ile
re co rd in g a n o th e r
Re co rd in g o ff tim e se ttin g
By setting the recording off time, the recording
stops and the VCR is turned off automatically.
1) While recording, press TV/VCR to turn off
“VCR” indicator.
While recording, press simultaneously both REC
on the remote repeatedly to set the desired off
time.
2) Choose another channel using the channel
selector on the TV.
Sk ip p in g u n n e ce ssa ry sce n e s w h ile
re co rd in g
Each time you press REC, each half-hour up to
about 4 hours appear cyclically.
Press PAUSE/STILL to stop recording
momentarily. To resume recording, press
PAUSE/STILL again.
VCR
Notes
Note
• To cancel the recording in progress, press
POWER on the VCR.
The VCR automatically shifts to the stop mode if the
recording pause mode continues for 10 minutes.
24
W522CG ENG new(24-29)
24
2/20/04, 11:19
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Timer Program Recording
The programmable timer allows you to record up to 6 different programs over one month.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• Make sure that the clock is set correctly ( page 15).
• Store the channels on the VCR (pages 16 and 17).
Tim e r Pro g ra m m in g Pro ce d u re
VCR
TV
POWER
Example: To record cable channel 25 in the SP tape speed from
9:20 p.m. until 10:00 p.m. on August 30. Today is August 25.
1
4
2
5
8
0
3
6
Number
buttons
CM SKIP
7
A.SELECT
9
Load a cassette with the safety tab attached.
1
100
ENTER
EJECT
Press PROG. to display the MENU screen.
2
PLAY
PLAY
REW
FF
FF
ENTER
Select “PROGRAM” using FF or
REW, and press ENTER.
3
STOP
STOP
REW
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
10
2,9
Move to the next using FF, and
4
select the channel number 25 by
pressing number buttons 2 and 5,
PLAY or STOP.
• You can make appear on the channel number position by pressing
I.SELECT depending on your connection.
(See pages 12).
To make corrections:
Press REW to move back to the item, or FF to forward.
(Continued)
25
W522CG ENG new(24-29)
25
2/20/04, 11:19
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer Program Recording (continued)
Move to the next using FF, and set
the recording date using PLAY or
5
STOP.
The date changes as follows:
…
…
→ 8/25 → 9/25 →
→ 7/25 → WKLYSU →
MO~FR ← WKLYSA ←
…
[WKLYSU] [WKLYSA]: You can record TV programs on the same
channel on the day and time every week.
[MO~FR]: You can record TV programs on the same channel on the
day and time Monday through Friday.
Move to the next using FF, and set
the hour and minutes of the
recording start time.
6
7
8
P
M
Move to the next, and set the
recording off time.
Move to the next, and select the
tape speed (SP) using PLAY or
STOP.
For the tape speed “AUTO (Auto Speed
Select)”, see below.
To set another program, press FF, and
select the next line pressing STOP.
Repeat steps 4 to 8.
Press PROG..
Now programming is completed.
9
REC
TIMER
Press both TIMER simultaneously.
10
The power turns off and the VCR enters
the timer standby mode.
TIMERHi-Fi
STEREO
L
SAP
Notes
Au to Sp e e d Se le ct
• Make sure that the tape length is selected correctly
according to the tape used on the SET UP screen
(page 22).
• When the SLP tape speed is selected and the tape
length is not sufficient to record the program to the
end, the program cannot be recorded to the end.
• The picture will be distorted when playing the part
where the recording tape speed is switched from
SP to SLP with the Auto Speed Select feature.
If you are not sure the tape is long enough for
timer program recording in the SP tape speed,
set the recording tape speed to “AUTO”.
Recording starts in the SP tape speed and the
VCR automatically selects the tape speed to
record the program to the end. If the tape length
is not long enough, the tape speed automatically
changes from SP to SLP.
26
W522CG ENG new(24-29)
26
2/20/04, 11:19
Download from Www.Somanuals.com. All Manuals Search And Download.
If a p o w e r fa ilu re o ccu rs d u rin g
th e tim e r p ro g ra m re co rd in g
Co n firm in g th e tim e r p ro g ra m s
• When a power failure has occurred, the
programmed contents are not affected,
reset the clock.
Press PROG. during timer recording mode.
The screen for confirming will appear.
P
P
M
M
O ve rla p s o f th e p ro g ra m s
If two timer programs overlap, the recording
start time of program 1 has priority over the
recording off time of program 2.
Press PROG.again to exit from confirmation
page.
Program 1
(Start time)
Ch a n g in g / ca n ce llin g th e tim e r
p ro g ra m s
Program 2
(Start time)
Overlapped portion
(not recorded)
1) If the TIMER indicator is lit, press both
TIMER to turn it off, and then turn the VCR
on by pressing VCR POWER.
2) With steps 2 to 9, change the items.
To cancel a program, select the program you
want to cancel in step 4, and press CANCEL.
The line is then cleared.
3) Press both TIMER to return to the timer
standby mode.
Erro r in d ica tio n
The “--E-” ( Error ) indicator appears in the VCR
display if you press both TIMER when:
–– a cassette is not loaded.
–– the loaded cassette has no safety tab.
–– timer recording is in progress.
In these cases, a recording can not be made.
To ca n ce l th e Tim e r Re co rd in g
By pressing the POWER button on the front
panel of the VCR, it will cancel the timer
recording and go to standby.
27
W522CG ENG new(24-29)
27
2/20/04, 11:19
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
MTS Broadcast Compatibility
This VCR can receive or record MTS (Multichannel TV Sound) broadcasts. By connecting the VCR to
your stereo system or stereo TV, you will experience the SAP or stereo sound.
Preparation
Connect a stereo TV or stereo system to the AUDIO OUT jacks of the VCR.
Re co rd in g th e SAP/ Ste re o Bro a d ca st
VCR
TV
POWER
1
4
2
5
8
0
3
6
On the SET UP screen (page 14),
select “SAP SET” using PLAY or
STOP, and set to “ON” using REW
or FF.
1
CM SKIP
7
A.SELECT
9
100
A.SELECT
EJECT
PLAY
REW
FF
ENTER
1
STOP
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
DISPLAY
I.SELECT
REC
TIMER
Press PROG. once to exit.
2
3
PROG. CANCEL
TV VOL
2
Perform a recording.
SAP (Second Audio Program broadcast):
A separate audio program, usually broadcast in a second language with the
main language.
Se le ctin g a so u n d
Sounds recorded on the tape
According to your setting of “SAP SET” on the SET UP screen, the sound is recorded onto different
tracks of the tape as below. Set “SAP SET” to “ON” or “OFF” appropriately.
Contents of recorded sound
On-Screen Display
(Press DISPLAY.)
Setting of “SAP SET”
on the SET UP
screen
Type of receiving
broadcast
Hi-Fi sound track
Normal sound
track (Mono)
“SAP”
not lit
“STEREO”
L
R
Regular
(monaural audio)
“ON” or “OFF”
not lit
MONO
MONO
MONO
Stereo
“ON” or “OFF”
“ON”
not lit
lit
lit
not lit
not lit
lit
MONO (MIXED)
MONO
STEREO
MONO
MONO
MONO
SAP
MONO
SAP
Regular+SAP
“OFF”
lit
MONO
“ON”
lit
MONO
Stereo+SAP
“OFF”
lit
lit
MONO (MIXED)
STEREO
Sounds in playback
You can play SAP and/or stereo broadcasts with this VCR. Press A.SELECT to select a desired sound.
Desired sound
SAP sound
L , R indicators in the On-Screen display
R (right) is on.
Sound output
SAP
Stereo sound
Both R (right) and L (left) are on.
HIFI Sound
Note
When the TV is connected to the RF OUT terminal of the VCR, the output sound is monaural.
28
W522CG ENG new(24-29)
28
2/20/04, 11:19
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL INFORMATION
Remote Control for TOSHIBA TVs
The remote control can control TOSHIBA TVs.
TO SHIBA TV’s Co n tro l
1
VCR
TV
POWER
POWER
Press TV to set the remote control operating your TV.
1
4
2
5
8
0
3
6
1
2
CH/TRK
CM SKIP
7
A.SELECT
9
Point the remote control at your TV and use each button
listed below to make sure that your TV is operate correctly.
100
100
Number
buttons
EJECT
PLAY
REW
FF
ENTER
ENTER
POWER
CH/TRK
To turn the TV on or off.
To select TV channels in the upper or lower
direction.
STOP
SLOW
DISPLAY COUNTER
PAUSE/STILL
SP/SLP
REMAIN/
COUNT
RESET
DISPLAY
I.SELECT
REC
TIMER
PROG. CANCEL
TV VOL
TV VOL
To adjust the sound level.
I.SELECT
To select an external source such as a VCR.
Number buttons To select TV channels. When selecting channels
TV VOL
1 to 9, first enter 0 and then the desired number.
I.SELECT
100
DISPLAY
ENTER
To substitute for 100 channel key.
To turn on or off TV’s screen display.
To use for the TV’s ENTER key.
Important
Some TV’s may not respond to all
the operations above, or may not
be operated at all with this remote
control. in this case, operate your
TV with it’s own remote control.
29
W522CG ENG new(24-29)
29
2/20/04, 11:19
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL INFORMATION
Before Calling Service Personnel
Check the following symptoms before requesting servicing.
N o ise is p re se n t in th e Hi-Fi so u n d
b e in g p la y e d .
N o p o w e r.
• The power cord is not plugged in.
• Tracking is not set appropriately.
– Plug the power cord into the outlet firmly.
– Adjust the tracking manually. (page 19)
Alth o u g h th e p o w e r is o n , th e VCR
w ill n o t w o rk .
• There is no cassette.
Th e tim e r re co rd in g fu n ctio n d o e s
n o t w o rk .
• There is an error in programming.
– Load a cassette. (page 18)
– Reset the timer recording program. (page 27)
Th e clo ck d o e s n o t w o rk .
• There has been a power failure.
– Reset the clock. (page 15)
• There is no cassette in the VCR.
– Load a cassette with the safety tab attached.
(page 18)
Th e tim e r d o e s n o t w o rk p ro p e rly.
• The cassette does not have the safety tab.
• The time is incorrect.
– Set the clock correctly. (page 15)
– Use another cassette with a safety tab or
cover the hole with adhesive tape. (page 18)
• The timer indicator is not displayed.
– Press both TIMER simultaneously. (page 26)
Th e p ictu re d o e s n o t a p p e a r o n th e
TV scre e n .
• There has been a power failure.
– Reset the clock. (page 15)
• The video channel or video input mode is not
set correctly.
– Set the TV channel to the video channel ( 3
or 4 ) or set the video input mode on the TV.
(page 11,14)
Th e re m o te co n tro l d o e s n o t w o rk
p ro p e rly.
• The batteries are exhausted.
– Replace all batteries. (page 10)
• The TV signal is weak.
– Adjust the antenna direction or use an
optional antenna booster.
• The remote control is operated beyond the
operating range.
• The power cord is not plugged in.
– Plug the power cord into the outlet firmly.
– Make sure the remote control is within 30° of
the remote sensor on the VCR. (page 10)
Th e p ictu re d o e s n o t a p p e a r o n th e
TV scre e n d u rin g re co rd in g a n d
p la y b a ck .
• Too far from the VCR.
– Use the remote control within 7 m from the
front of the VCR. (page 10)
• The video channel or VCR mode is not set
correctly.
– Press TV/VCR to select the VCR mode and
• An obstacle may be in the way of the operation.
– Remove the obstacle.
set the TV channel to 3 or 4. (pages 11,14, 24)
• The operating mode of the remote control is not
set correctly.
– Press VCR or TV depending on the
Th e VCR d o e s n o t re co rd .
• The loaded cassette has no safety tab.
equipment you want to operate. (pages 14,29)
– Use a cassette with a safety tab or cover the
hole with adhesive tape. (page 19)
Th e ca sse tte is e je cte d im m e d ia te ly
a fte r it is lo a d e d .
• The cassette was inserted with the label side
not paralleling the compartment.
Th e p la y b a ck p ictu re is p o o r.
• Tracking is not set appropriately.
– Adjust the tracking manually. (page 19)
– Reload it carefully. (page 18)
• The video heads are dirty.
– Clean the video heads with a commercially
available cleaning tape.
Th e ca sse tte d o e s n o t g o in to th e
ca sse tte co m p a rtm e n t.
• There is already a cassette in the VCR.
– Eject the cassette and reload the new one.
(page 18)
Th e d e sire d so u n d is n o t h e a rd , su ch
a s SAP, ste re o , o r re g u la r so u n d .
• Setting of sounds is not correct.
– Select a desired sound using A.SELECT. (page 28)
30
W522CG ENGnew (30-32)
30
2/20/04, 11:20
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power Supply:
120 V AC, 60 Hz
Power consumption:
External dimensions:
Mass:
18 W
360 x 94 x 252mm (W.H.D.)
3.0 kg
Channels received:
VHF: Channels 2–13
UHF: Channels 14–69
CATV: Channels A7-A1,A-CCC, 66-125
UHF/VHF: 75 Ω F type connector
Standard NTSC
Antenna input/output terminals:
Signal system:
Recording/Playback system:
Recording: VHS format (SP, SLP)
Playback: VHS format (SP, LP, SLP)
Cassette:
Video cassette with
mark
Tape speed:
SLP: 11.1 mm/s, SP: 33.4 mm/s
Video recording/playback time:
SLP: 480 minutes, SP: 160 minutes (When T-160
video cassette is used.)
Fast forward/rewind time:
Video input:
Within approx. 60 s (When T-120 video cassette is
used.)
1 V (p-p), 75 Ω, unbalanced, negative sync., pin
jack
Video output:
1 V (p-p), 75 Ω, unbalanced, negative sync., pin
jack
Audio input:
Line input: 308 mV (rms), more than 47 kΩ, pin
jack
Audio output:
Line output: 308 mV (rms), less than 4.7 kΩ, pin
jack
Audio frequency range (Hi-Fi) :
Audio dynamic range (Hi-Fi) :
Utilization conditions :
20 Hz – 20 kHz
68 dB
Temperature: 5°C to 40°C
Humidity: less than RH 80%
Accessories
Antenna cable ....................................... 1
Remote control..................................... 1
Batteries (AA) .................................... 2
Designs and specifications are subject to change without notice.
31
W522CG ENGnew (30-32)
31
2/20/04, 11:20
Download from Www.Somanuals.com. All Manuals Search And Download.
CANADIAN WARRANTY
TOSHIBA VIDEO CASSETTE RECORDER
To obtain a “CANADIAN WARRANTY”, the consumer must complete and forward the attached
“CANADIAN WARRANTY REGISTRATION FORM” to Toshiba of Canada Limited, Consumer
Electronics Group Warranty Registration Office, 191 McNabb Street, Markham, Ontario L3R
8H2 within 30 days of purchase!
This warranty ofter provides the manufacturer’s parts and labour warranty provided that
the consumer registers for a CANADIAN WARRANTY.
To obtain service under warranty, contact the nearest authorized TOSHIBA SERVICE
CENTRE or the nearest TOSHIBA FACTORY SERVICE DEPARTEMENT (list enclosed).
PRODUCT UTILIZED FOR RENTAL OF COMMERCIAL PURPOSES ARE NOT COVERED
BY THIS WARRANTY.
Thiswarrantyappliesonlytotheoriginalpurchaserandisnottransferable. Thevideohead
warrantyisalsocovered,duringwhichTOSHIBAwillprovideareplacementheadwarranted
for the unexpired portion of the warranty. This warranty does not apply to sets subjected
to misuse, neglect, accident, act of God or improper installation. Sets with serial number
removed, altered, replaced or defaced will not be covered by this warranty. ALL IN-
WARRANTYREPAIRSMUSTMEMADEBYATOSHIBAFACTORYSERVICEDEPARTEMENT,
OR BY AN AUTHORIZED TOSHIBA SERVICE CENTRE. REPAIRS MADE ELSEWHERE
WILL INVALIDATE THIS WARRANTY.
THISWARRANTYISONLYVALYDWHENTHESETISPURCHASEDFROMANAUTHORIZED
TOSHIBA DEALER AND USED IN CANADA
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, GUARANTIES OR
AGREEMENTS, WHETHER EXPRESSED OR IMPLIED, AND NO PERSON, AGENT,
DISTRIBUTOR, DEALER, SERVICE CENTRE OR COMPANY IS AUTHORIZED TO CHANGE,
MODIFY OR EXTEND ITS TERMS IN ANY MANNER WHATSOEVER.
IMPORTANT: Also keep your “Bill of Sale” as proof of purchase.
WARRANTY:
TYPE OF SET:
PARTS:
Carry-in Service
Colour Video Cassette Recorder
12 Months
LABOUR:
12 Months
VIDEO HEAD:
12 Months
Thank you for purchasing this fine product from one of your authorized: CANADIAN
TOSHIBA DEALERS.
TO SHIBA O F CAN ADA, LTD.
HEAD OFFICE
191 MCNABB STREET MARKHAM, ONTARIO L3R 8H2, CANADA
SERVICE CENTER
TEL: (905)470-5400
TORONTO: 191 MCNABB STREET MARKHAM, ONTARIO L3R 8H2, CANADA
MONTREAL: 1643 N. SERVICE RD. DORVAL, QUEBEC, H9P 1J1, CANADA
TEL: (905)470-5400
TEL: (514)856-4100
VANCOUVER: 22171 FRASERWOOD WAY, RICHMOND, B.C. V6W 1J5, CANADATEL: (604)303-2500
Printed in Indonesia
W522CG ENGnew (30-32)
32
2/20/04, 11:20
Download from Www.Somanuals.com. All Manuals Search And Download.
|