TOS HIBA
DISK PRODUCTS DIVISION
SD-W1111
DVD-RAM DRIVE
PRODUCT SPECIFICATION
JUNE 1999
REV. 1.0
Specifications are subject to change without notice
DOCUMENT NUMBER
12043
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
Matters to be attended to:
This drive adopts RPC-II for its “Standard Specification Model”.
This DVD-RAM Drive adopts RPC-II, the Phase II System of RPC (Regional Playback Control) for “Standard
Specification Model”, on the basis of a contract with the CSS (Contents Scramble System) organization. (all of our
former DVD-RAM Drives adopted RPC-I, the Phase I System.)
The CSS rule requires that all the products not only DVD-RAM Drives but also PC systems installing DVD-RAM
Drives sold from Jan.1, 2000 need to support RPC-II described above.
To playback a DVD-Movie Software with the Regional Code specified by using a DVD-RAM Drive with RPC-II
adopted, either the hardware or software used as applications on PC system side is also required to meet RPC-II.
Namely, in the status that a hardware or a software for a DVD-Movie Playback Application planned to use in a PC
does not support RPC-II, if the "RPC-II (Standard Specification) Drive" is used in combination, DVD-Movie
Softwares with the Regional Code specified (most of DVD-Movie Softwares currently available on the market)
cannot be reproduced. So, in such a case, "RPC-I Specifications Supported Model" must be purchased for a while.
However, all the drive manufacturers must obey to the deadline specified by the CSS rule saying; all DVD-RAM
Drives have to implement Phase II from Jan.1, 2000. So we recommend that you will change your DVD-Movie
Playback Hardware or Software to those applicable to the PRC-II as soon as possible and investigate to combine
your system with the RPC-II Specification Drives.
Since we determine the drives are of RPC-I or RPC-II when manufacturing at factory and ship, the specification
change after shipping is not available in principle. Especially, changing the RPC-II specification drive to the RPC-
I is prohibited by the CSS rule.
In the combination of the drive and PC system with RPC-II supported, as far as the Regional Code of a DVD-Movie
Software and the code memorized in the RPC-II Specification Drive coincides, the Movie Software is allowed to
carry out.
In the RPC-II Specification Drive, the region change by an end user is permitted up to 5 times in total including the
initial region set. After change to the fifth region is carried out, the Drive enters Parm State (“no change allowed”
status).
The drive with Parm State is permitted up to 4 times of "reinitialization" by a drive manufacturer or a specific
service center authorized by the CSS. Since it is considered that the reinitialization is carried out after the
completion of the region confirmation through test items in the PC manufacturer’s manufacturing line or the
completion of drive repair, etc., the number of reinitialization times may vary from 0 (no reinitialization available)
to 4 times. So, we recommend that not to disclose the reinitialization process to end users but only to inform the
number of region setting times as "end user’s direct region setting is available up to 5 times in total."
Page 2
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
Precaution
This equipment (an optical disc drive) handled under the conditions out of product specifications may
cause injury, heat generation, trouble, erroneous operation and performance degradation, so, care will be
necessary, and proper handling according to the precautions shown below will be required. In case of
mishandling without keeping the cautions, safety, reliability and performance of the product are not
guaranteed. For systems using this equipment, please note it above mentioned on manuals etc. to
understand the users completely.
Cautions
(1)Don’t loosen screws except persons trained with specified instructions. The reliability, safety and
performance specified in this specification can not be satisfied.
(2)Don’t modify this equipment. The reliability, safety and performance specified in this specification can
not be satisfied.
(3)Don’t insert any objects or cartridge other than specified from the cartridge insertion slot. It may cause
trouble or erroneous operation.
(4)Don’t give excessive vibration and shock this equipment. It may cause trouble or erroneous operation.
(5)Toshiba Corporation makes no warranty of any kind, either expressed or implied, including, but not
limited to, the implied warranties of merchantability and fitness for a particular purpose. This product
may sustain damages which may cause errors and failures. The causes are not confined to what are
mentioned or implied in this document. Therefore, the possibilities of error and failure should be taken
into consideration when furnishing systems should be protected by such means as system backup and
mirroring disk subsystem, especially when this product is used for systems as medical appliances.
Toshiba Corporation shall not be liable for incidental or consequential losses or damages to tangible
property, injury or death of person in connection with the errors and failures which may occur when
furnishing, operating or using this product
(6)When a disc cannot be ejected because of some troubles, etc., turn off the power for this equipment and
eject the disc using the emergency eject mechanism after passing more than 1 minute. When the
emergency eject is carried out while the power is on or immediately after the power off, the disc may be
ejected in a rotating status. Toshiba Corporation does not assure if the disc is damaged by this.
Page 3
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
1. Scope.................................................................................................................................................... 6
2. Features................................................................................................................................................ 6
3. External views and dimensions ............................................................................................................. 7
4. Basic specifications .............................................................................................................................. 8
5. Power supply specifications ................................................................................................................ 10
5.1 Input power supply....................................................................................................................... 10
5.2 Power consumption ...................................................................................................................... 10
5.3 Allowable ripple voltage............................................................................................................... 10
6. Mechanical specifications ................................................................................................................... 10
6.1 Dimensions .................................................................................................................................. 10
6.2 Mass ............................................................................................................................................ 10
6.3 Disc loading ................................................................................................................................. 10
6.4 Optical head auto-lock mechanism................................................................................................ 10
7. Reliability specifications..................................................................................................................... 11
7.1 Error rate...................................................................................................................................... 11
7.2 Life .............................................................................................................................................. 11
8. Environmental specifications .............................................................................................................. 11
8.1 Temperature ................................................................................................................................. 11
8.2 Relative humidity......................................................................................................................... 12
8.3 Vibration ...................................................................................................................................... 12
8.4 Shock........................................................................................................................................... 12
8.5 Altitude........................................................................................................................................ 12
8.6 Static electricity............................................................................................................................ 12
8.7 Acoustic noise.............................................................................................................................. 12
8.8 Applicable regulations.................................................................................................................. 12
9. Block diagram .................................................................................................................................... 14
10. Mounting............................................................................................................................................ 15
10.1 Mounting...................................................................................................................................... 15
10.2 Mounting direction....................................................................................................................... 16
10.3 Notes on mounting ....................................................................................................................... 17
11. Front bezel.......................................................................................................................................... 19
11.1 Standard Bezel ............................................................................................................................. 19
11.2 LED lighting ................................................................................................................................ 19
12. Rear View and Connectors.................................................................................................................. 21
12.1 Power supply connector................................................................................................................ 21
12.2 I/F connector (SCSI connector)..................................................................................................... 22
12.2.1 Pin No. table of connector terminal .......................................................................................... 22
12.2.2 External view diagram.............................................................................................................. 23
12.2.3 Signal interface ........................................................................................................................ 23
12.3 Mode select headers functions ...................................................................................................... 24
12.3.1 SCSI ID setting ........................................................................................................................ 24
12.3.2 Parity check setting .................................................................................................................. 24
12.3.3 VERIFY setting ....................................................................................................................... 24
12.3.4 ONE LUN/TWO LUN setting.................................................................................................. 25
12.3.5 Termination setting................................................................................................................... 25
12.3.6 Change of setting ..................................................................................................................... 25
12.4 Audio Connector .......................................................................................................................... 25
13. Host interface specification................................................................................................................. 26
13.1 Applicable standard...................................................................................................................... 26
13.2 SCSI command set ....................................................................................................................... 26
14. Notes on data guarantee...................................................................................................................... 28
14.1 Disappearance of data in buffer in a write cache operation............................................................ 28
14.2 Error report in a write cache operation.......................................................................................... 28
14.3 Automatic sector replacement at a write operation ........................................................................ 28
14.4 Verification of a block address...................................................................................................... 28
14.5 Error generation in Read Modify Write operation ......................................................................... 28
Page 4
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
15. MISCELLANEOUS ........................................................................................................................... 30
15.1 Accessories .................................................................................................................................. 30
15.2 A bare disc setting at vertical installation...................................................................................... 30
15.3 Disc eject at emergency................................................................................................................ 33
Page 5
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
1. Scope
The specification is applied to DVD-RAM drive SD-W1111.
2. Features
(1) 2.6 GBytes capacity on one side of a 120 mm disc
·
Using 650 nm short-wavelength laser, 0.74 mm single spiral land and groove tracking and Z-CLV
system, realizes the memory of 2.6 GBytes (decimal) on one side of a 120 mm disc.
(2) High data recording rate by over-writing system
·
Phase change recording technology enables to write data directory into the media without waiting for
pre-erasing (one-path direct over-writing system).
(3) Playback interchangeability for CD-ROM and DVD-ROM discs
Playback a disc either for CD-ROM, CD audio or DVD-ROM.
(4) High-speed data transfer rate
·
·
·
Possible to record and playback MPEG2 compressed motion picture (MP@ML) in a real time.
Owing to the read/write cache, improves the data throughput marvelously.
(5) Low power consumption of 6.7W (typ.) using +5V single power supply
·
Owing to the low power consumption design to operate using +5V single power supply, no exclusive
fan is required.
(6) Dust prevention structure
Original sealing structure provides dust prevention features.
(7) Easy contact and operation
·
·
·
Employs the SCSI interface that is easy to connect with various platform .
Possible to install vertically as well as horizontally.
(8) High reliability
·
·
MTBF 100,000H (under specified conditions)
Powerful error correction ability by employing the erasure correction system using the ECC block
which is same as the DVD-ROM system.
Page 6
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
3. External views and dimensions
External views: 146.0 x 203.0 x 41.3 (mm) (W x D x H) (Except for front bezel)
Page 7
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
4. Basic specifications
·
5.25” half height form factor
·
Applicable discs(1GB = 230 Byte, 1MB = 220 Byte 1KB = 210 Byte)
1) DVD-RAM *1
DVD Specifications for Rewritable Disc Part 1 Version 1.0
2.42 GBytes*2 x 1
(Cartridge with a single-sided disc provided / No cartridge) *3
2.42 GBytes x 2
(Cartridge with a double-sided disc is provided / No cartridge)
2) DVD-ROM
DVD Specifications for Read-Only Disc Part 1 Version 1.0
4.38 GBytes x 1 or 2 Single-layer disc
7.96 GBytes x 1 or 2 Dual-layer disc
3) DVD-R (Read only) *4
4) CD-ROM
Red-book, Yellow-Book, CD-ROM XA, CD-I Bridge (Photo-CD, Video-CD)
CD-I*5, CD-I Ready, CD-G, CD-TEXT, Multi-session (Photo CD Disc, CD-Extra)
5) CD-DA playback to Analog audio output
6) CD-R (Read only) *4
7) CD-RW (Read only) *4
*1: Toshiba designate a recommend disc the performance of which has been checked by this drive.
*2: Formatted user capacity: 2.32GB
*3: When using a disc without using a cartridge, limitation on function features may occur.
*4: Depending on the feature of a recording unit that records data, playback function may not be
guaranteed.
*5: Need special hardware and software for playback.
·
·
Disc diameter
120 mm/80mm (CD single, DVD-ROM single)
Rotational speed
1,028 – 2,400 rpm (DVD-RAM)
1,200 – 2,800 rpm (DVD-ROM Single-layer)
1,300 – 3,000 rpm (DVD-ROM Dual-layer and DVD-R)
3,516 rpm
(CD-ROM)
·
Transfer rate (sustained) (1KB = 210 Byte=1,024 Byte)
1,350 KB/s
2,700 KB/s
(DVD-RAM)
(DVD-ROM, DVD-R)
990 – 2,400 KB/s (CD-ROM, CAV, 6.6 to 16X )
Host I/F
·
SCSI
Command set
SFF8090 Ver. 2 Rev 0.95
ANSI X3T9.2 Rev10L
Transfer rate (burst)
Single ended driver
5MB/s max. (at asynchronous transfer)
10MB/s max. (at synchronous transfer)
Page 8
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
·
Average seek time (Operating time of SEEK command)
DVD-RAM
DVD-ROM
120 ms (typ.)
210 ms (typ.)
140 ms (typ.)
CD-ROM
·
Average access time
DVD-RAM playback
DVD-ROM
180 ms*1 (typ.)
260 ms*1 (typ.)
170 ms*2 (typ.)
CD-ROM
*1 Operation time when playing back 1ECC block by READ command
*2 Operation time when playing back 1 sector by READ command
·
Start time (average): START UNIT command execution time (w/o loading tray)
DVD-RAM
15.0 s*
7.0 s
DVD-ROM (Single-layer)
DVD-ROM (Dual-layer)
CD-ROM
12.0 s
7.0 s
* Start time may be longer depending on the defect number registered
·
·
Restart time
1.0 s (from idle to active)
2.0 s (from sleep to standby)
I/O terminal
I/F connector
Mode select header
Applicable to 2.54 mm pitch flat cable.
1 Vrms, Unbalanced
CD audio connector
Power supply connector
Physical recording size(DVD-RAM)
Logical sector size
·
·
·
·
32 KBytes (ECC block unit)
2 KBytes
Data buffer
2 MBytes
Initialize time
Less than 1.0s
(Time until the unit responds to the command after power turns on.)
Page 9
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
5. Power supply specifications
5.1 Input power supply
+5V ± 5%, peak current 3A (Max. 2 sec., at spindle motor ON/OFF)
Note: Power supply current is usually 1.4A. But at a spin-up time the current increase to 3.0A. If the
power supply cable that is long and thin, power supply voltage is drop and out of the
operational condition of this drive. Please use a short and thick power supply cable.
Note: The voltage drop with the power supply cable is approximately as follows.
Wire
Resistance (W/km) Voltage drop (V)* at 1m wire length and 3A current
AWG22 (Twist wire)
AWG18 (Twist wire)
AWG22 (Single wire)
AWG18 (Single wire)
57.4
23.7
56.3
22.2
0.344
0.142
0.338
0.133
* The drop voltage in the both of the ground line and the power supply line
* This value changes according to the electric wire maker and the use temperature.
5.2 Power consumption
Average
Less than 6.7W
Less than 6.0W
Less than 11.0W
Less than 1.0W
Stand-by period:
Seek period:
Sleep period:
5.3 Allowable ripple voltage
Less than 100 mVp-p (includes spike noise)
6. Mechanical specifications
6.1 Dimensions
Refer to the drawing attached. (3. External views and dimensions)
6.2 Mass
1.14kg (Net ,include front bezel)
6.3 Disc loading
Auto-loading tray system (Bare disc, cartridge disc)
Tray load/unload mechanism
1) Load/Unload operation by the load/unload switch
2) Load operation by pressing the tray.
3) Load/Unload operation by the command.
4) Emergency eject function
6.4 Optical head auto-lock mechanism
To protect the optical head while transporting the drive, the optical head auto-lock function is
provided.
Be sure to avoid transport with a disc loaded.
Page 10
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
According to the steps described below, the optical head auto-lock mechanism can be functioned.
·
·
·
Eject a disc.
Pull-in the tray inside the drive.
After “BUSY” lamp turns off, the auto-lock function completes.
When transporting, transport the drive after performing the steps above and turning off the power.
7. Reliability specifications
7.1 Error rate
DVD-RAM
Read error rate
Seek error rate
less than 10–15 (Byte error rate)
less than 10 –6 error/seek
DVD-ROM
Read error rate
Seek error rate
less than 10–15 (Byte error rate)
less than 10 –6 error/seek
CD-ROM
Read error rate (Mode 1)
Read error rate (Mode 2)
Seek error rate
less than 10–15 (Byte error rate)
less than 10–12 (Byte error rate)
less than 10 –6 error/seek
Allows five times internal retry operations.
7.2 Life
Either of shorter life of 5 years or 15,000 POH
Loading mechanism
MTBF
10,000 times
100,000 H
Setting conditions:
Power on period
Power on time
Access times
5,436 H/year (17 H/day)
313 times/year
600,000 times/year
Using duty
Playback :
Recording :
20%
2%
8. Environmental specifications
The drive might satisfy the basic specification over the following conditions.
8.1 Temperature
Operating
5 to 50 °C
(Temperature variation gradient: 10°C/h)
–10 to 60 °C
Storing
(Temperature variation gradient: 20°C/h, except for media)
–40 to 65 °C
Transporting (with packing)
(Temperature variation gradient 20°C/h, except for media)
Page 11
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
8.2 Relative humidity
Operating
8 to 80% RH
5 to 95% RH
5 to 95% RH
Storing
Transporting (with packing)
(Temperature variation gradient: 10% /h, absolute humidity: 30 gm3) * No dew condensation
8.3 Vibration(5 to 300 Hz)
Operating
2.45 m/s2 (0.25G)0-p
9.8 m/s2 (1.0G)0-p
9.8 m/s2 (1.0G)0-p
Non-operating
Transporting (with packing)
8.4 Shock(Half sine wave 11 msec., interval 2 sec., 5 cycle)
Operating
14.7 m/s2 (1.5G)0-p
490 m/s2 (50G)0-p
Non-operating (disc not loaded)
8.5 Altitude
Operating
0 to 3,000 m
0 to 12,000m
Transporting (with packing)
8.6 Static electricity
Specification
IEC801-2
Operation
6 KV or lower
15 KV or upper
Damage
8.7 Acoustic noise
45 dB (Max.)
Measurement conditions:
·
·
·
1m away from the drive
JIS A correction
Standard front bezel attached
8.8 Applicable regulations
(1) UL1950 3rd
(2) CSA C22.2 No. 950 3rd
(3) TUV (EN60950/EN60825-1)
(4) DHHS 21 CFR Sub-Chapter J
(5) CE standard
EN50081-1
: 1992
EN55022+A1
EN50082-1
: 1994 class B
: 1997
EN61000-4-2
EN61000-4-3
ENV50204
: 1995
: 1996
: 1995
EN61000-4-4
EN61000-4-5
: 1995
: 1995
Page 12
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
EN61000-4-6
EN61000-4-8
EN61000-4-11
: 1996
: 1993
: 1994
Page 13
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
9. Block diagram
Page 14
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
10. Mounting
10.1 Mounting
Mount the drive using four M3 tapping holes bottom and two M3 tapping holes on each side.
The following shows an example mounting on a personal computer or a sub system.
Flatness deviation under 0.5mm
Use screws of which length
inside the drive should be
more than 2.5mm and less
than 3.5 mm from the drive
frame surface.
Keep this gap less than
0.5mm .
Before fixing
After fixing
Page 15
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
10.2 Mounting direction
Install direction
Horizontal or vertical installation
(When using an 80mm disc, vertical direction installation is not allowed.)
Allowable slants (Refer to the drawing.)Left/right directions: Within ±15°.
(When installing vertically, the allowable slants toward the top plate bottom
should be 0°.)
Front/rear directions:Within 10°
15° max
15° max
15° max
10° max
10° max
Page 16
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
10.3 Notes on mounting
·
Keep more than 5mm clearance to circulate an adequate amount of air by convection around the drive
and mounting metal parts.
·
Keep more than 0.8mm clearance around the top cover in order to secure absorbing shock and
vibration.
Page 17
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
· Do not apply force (under 1.5N : 150gf) caving in the top plate.
‘99/06/26 Version 1.0
·
Use screws of which length inside the drive should be more than 2.5mm and less than 3.5 mm from the
drive frame surface.
Drive Frame
M3 screw
2.5-3.5mm
Page 18
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
11. Front bezel
11.1 Standard Bezel
The front view of the drive with a standard bezel
Emergency
disc eject hole
Load/Unload switch
LED: “ROM” “RAM” “BUSY”
·
·
·
Load/Unload switch:
Push when ejecting/pulling-in the tray
Emergency disc eject hole:
When ejecting a disc with power turned off, insert an exclusive tool to eject a disc. (Refer to 15.3)
LED:
“BUSY” (orange):
Lights when the drive operates.
“RAM” (green):
“ROM” (green):
Lights when DVD-RAM disc is loaded.
Lights when either of DVD-ROM, DVD-R or CD-** is loaded.
11.2 LED lighting
Closing the tray, “BUSY” LED lights and the drive status becomes as follows;
(1) A disc is loaded and the drive status becomes “Ready”, “RAM” LED or “ROM” LED turns on
according to the disc type and “BUSY” LED turns off.
“ROM” or “RAM”
“BUSY”
(2) A disc is loaded but the drive status doesn’t become “Ready”, all LEDs turn off.
all LEDs turn off
“ROM” or “RAM”
“BUSY”
Page 19
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
(3) A disc is not loaded, all LED’s turn off.
‘99/06/26 Version 1.0
all LEDs turn off
“ROM” or “RAM”
“BUSY”
(4) While executing following command, “BUSY” LED turns on.
executing the command
“BUSY”
Command
REASIGN
READ
WRITE
SEEK
WRITE & VERIFY
SEND DIAGONOSTIC
SET READ AHEAD
START / STOP UNIT
VERIFY
READ HEADER
GET PERFORMANCE
(5) While executing FORMAT command, “RAM” LED turns on and “BUSY” LED blinks on about
1.6sec cycle.
1.6 s
“BUSY”
(6) While playing a CD audio track, “ROM” LED turns on and “BUSY” LED blinks on about 2.0sec
cycle.
2.0 s
“BUSY”
Page 20
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
12. Rear View and Connectors
The rear view of the drive
Power supply
connector
Audio connector for CD
Mode select headers
I/F (SCSI) connector
·
·
·
·
Power supply connector (4 pin): DC power supply is to be connected.
I/F (SCSI) connector (50 pin): SCSI connector is to be connected.
Modes select headers (2 x 8 bits): Used to perform function settings.
Audio connector for CD (4 pin): CD audio outputs.
12.1 Power supply connector
Pin No.
Connection
+5V
1
2
3
4
GND
GND
NC
1
2
3
4
Use the plug of IRISO ELECTRONICS P/N9047b-54Z12-GT or equivalent one.
Page 21
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
12.2 I/F connector (SCSI connector)
12.2.1 Pin No. table of connector terminal
Pin
1
Signal
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Open
Pin
2
Signal
DB0
3
4
DB1
5
6
DB2
7
8
DB3
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
DB4
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
DB5
DB6
DB7
DBP
Ground
Ground
Ground
TERMPWR
Ground
Ground
ATN
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
BSY
ACK
RST
MSG
SEL
C/D
REQ
I/O
*Notes 1) the low level of all signals returns TRUE.
Use Hirose Electronics Co. HIF 3BB-50DA-2.54R, Molex 5320-50AT2 or equivalent one for the
connector on cable side.
The voltage is added on the TERMPWER signal from the internal side of a drive. The maximum
power supply current from internal side of a drive is 1.1A. If the current exceeds this level, the
internal current limiter operates to stop the voltage addition. After the cause of excess current is
removed, the signal returns to the original status.
Page 22
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
12.2.2 External view diagram
‘99/06/26 Version 1.0
12.2.3 Signal interface
Type
50 core flat cable or 25 couple stranded wire cable
more than AWG28
Inductor size
Characteristic impedance 100ohm ± 10%
Maximum cable length
3.0m
Page 23
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
12.3 Mode select headers functions
By inserting the jumper wire to the mode select headers , each kind of operation mode is made.
Mode select headers:2.54-mm pitch
Interface
Connector
Mode Select Headers
CD Audio
Connector
Pin No. 1
Pin No.
2
3
4
5
6
7
8
Functions
Setting at shipping
Open
1
2
3
4
5
6
7
8
SCSI ID1 (LSB)
SCSI ID2
SCSI ID4 (MSB)
PARITY CHECK
VERIFY
Open
Short
Open
Open
Open
Open
Open
ONE LUN/TWO LUN
Reserved
Termination
12.3.1 SCSI ID setting
Pin 1
ID1
Pin 2
ID2
Pin 3
ID3
Pin 4
ID4
0
1
2
3
4
5
6
Open
Short
Open
Short
Open
Short
Open
Short
Open
Open
Short
Short
Open
Open
Short
Short
Open
Open
Open
Open
Short
Short
Short
Short
7
12.3.2 Parity check setting
Pin 4
Open
Short
Functions
Data parity check enable.
Data parity check disable.
12.3.3 VERIFY setting
l Verify setting function is effective to WRITE command only.
l The RAM disc re-inserted into TYPE-2 case is verified ,even if the pin5 is shorted.
Pin 5
Functions
Open
Short
The drive verifies the written data, on the media
after the write operation. Writing speed is lower,
but data reliability is better.
The drive does not verify the written data after the
write operation. The drive cannot detect the
defect on the media, but Writing speed is higher.
Page 24
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
12.3.4 ONE LUN/TWO LUN setting
‘99/06/26 Version 1.0
Pin 6
Function
Open
Short
The drive operates in ONE LUN mode.
The drive operates in TWO LUN mode.
ONE LUN mode: The drive operates in one LUN (Logical Unit Number) for all discs to
which SFF8090 Ver. 0.2 supports.
TWO LUN mode: The drive operates in the following two LUNs.
LUN = 0:
LUN = 1:
CD-ROM, CD-R, CD-RW, DVD-ROM, DVD-R disc (Device type = 5)
DVD-RAM disc (Device type = 7)
(LUN = 0/1
The selection of either 0 or 1 is switched according to a disc inserted.)
12.3.5 Termination setting
Pin 8
Open
Short
Function
Termination disable.
Termination enable.
When the termination enabled, the following circuit is connected to each SCSI signal.
2.85V
I/F signal
110W
12.3.6 Change of setting
The setting change should be carried out after turning off the power.
12.4 Audio Connector
When playing back a CD audio disc, the terminal develops the audio signal.
Pin No.
Signal
R
GND
GND
L
1
2
3
4
1
2
3
4
Connection should be done using a connector, part number:103959-3, manufactured by AMP or
equivalent one.
Page 25
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
13. Host interface specification
13.1 Applicable standard
SCSI
Command set
SFF8090 Ver. 2 Rev 0.95
ANSI X3T9.2 Rev 10L
13.2 SCSI command set
Code (Hex.)
Command
00
01
03
04
07
12
15
16
17
1A
1B
1D
1E
23
25
28
2A
2B
2E
2F
35
37
3B
3C
42
43
44
45
46
47
4A
4B
4E
55
56
57
TEST UNIT READY
REZERO UNIT
REQUEST SENSE
FORMAT UNIT
REASSIGN BLOCKS
INQUIRY
MODE SELECT (6)
RESERVE (6)
RELEASE (6)
MODE SENSE (6)
START STOP UNIT
SEND DIAGNOSTIC
PREVENT/ALLOW MEDIUM REMOVAL
READ FORMAT CAPACITIES
READ CD/DVD CAPACITY
READ (10)
WRITE (10)
SEEK
WRITE AND VERIFY (10)
VERIFY (10)
FLUSH CACHE
READ DEFECT DATA
WRITE BUFFER
READ BUFFER
READ SUB-CHANNEL
READ TOC/PMA/ATIP
READ HEADER
PLAY AUDIO (10)
GET CONFIGURATION
PLAY AUDIO MSF
GET EVENT/STATUS NOTIFICATION
PAUSE/RESUME
STOP PLAY/SCAN
MODE SELECT (10)
RESERVE (10)
RELEASE (10)
Page 26
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
Code (Hex.)
5A
Command
MODE SENSE (10)
SEND EVENT
A2
A3
SEND KEY
A4
REPORT KEY
A5
PLAY AUDIO (12)
SET READ AHEAD
READ (12)
A7
A8
AA
AC
AD
AE
WRITE (12)
GET PERFORMANCE
READ DVD STRUCTURE
WRITE AND VERIFY (12)
VERIFY (12)
AF
B6
SET STREAMING
READ CD MSF
B9
BA
BD
BE
SCAN
MECHANISM STATUS
READ CD
Page 27
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
14. Notes on data guarantee
14.1 Disappearance of data in buffer in a write cache operation
In a write cache operation, before data are actually written to a disc, a status response to the WRITE
command or WRITE & VERIFY command is sent. If the power supply is switched off immediately
after the status response, there is a possibility that the data in the buffer will disappear before being
written to the disc. To avoid this problem, execute FLUSH CACHE command before switching off
the power supply.
Always execute FLUSH CACHE command before switching off the power supply, to avoid any risk
of disappearance of data in buffer.
14.2 Error report in a write cache operation
When an error which cannot be recovered before all the data is received and written in the buffer and
a status response to the command is sent in the write cache operation, the error is reported as 71H in
REQUEST SENSE DATA. This shows that the error occurred on the last WRITE command or
WRITE & VERIFY command.
14.3 Automatic sector replacement at a write operation
When data can not be written to the disc normally due an unrecoverable error, such as ID NOT
FOUND, the drive replaces the sector by sector replacement processing. The drive prevents data
from being lost by this operation as much as possible. Because automatic sector replacement
processing is executed after write retry ends in an error, a time of between 7 to 15 seconds is needed.
Therefore, it is recommended that the time-out to the command generating access to the disc is set at
20 seconds or more. In a write cache operation, when automatic sector replacement processing is
done after a status response to the command is send, execution of the following command can be
made to wait. However, when the following command is a WRITE command or WRITE & VERIFY
command, the first data transfer of one block is executed without waiting, to prevent a time-out of the
host.
14.4 Verification of a block address
When the command is received, a drive calculates block addresses where the data are written or read,
with the start address and length specified by the command, and verifies whether the block addresses
contain a block address which does not exist. If such a block address exists is founded, the drive does
not record nor read, and reports on the error to the command at once.
14.5 Error generation in Read Modify Write operation
If, in a WRITE command and WRITE &VERIFY command, a start address number is not other than
*****0H or a block length is other than *16 x (integer)* though the start address number is *****0H,
the drive reads all data in an ECC block which contain the specified address once, and replaces the
data in the ECC block by the data of the specified address. This chain of operations is called "Read
Modify Write Operation". In "Read Modify Write Operation", in WRITE command and
WRITE&VERIFY command, an error occurs when the data of the ECC block cannot be read for
some reasons.
Page 28
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
Moreover, not only the data which tried to be recorded but also the data of other addresses in the
same ECC block might be lost due to the failure to record.
Page 29
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
15. MISCELLANEOUS
15.1 Accessories
Function setting jumper pins
Emergency eject tool
5 pieces.
1 piece.
15.2 A bare disc setting at vertical installation
In case of using a bare disc (ex. DVD-ROM or CD-ROM) at vertical installation, use disc holders on
the tray. Please read the following explanations thoroughly at this time.
1. Draw three disc holders among the four holders on the tray, two pieces are both holders in down
side, one piece is on a rear part in upper side while made to vertical posture as follows.
(Note) Please use 3 pieces holders because the set of the disc becomes difficult when four disc
holders are drawn out.
2. Drawing out a disc holder (pull return) can be easily done with inserting a propelling pencil ahead
in the hole that is installed on the disc holder.
Page 30
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
3. First hang a disc on a disc holder in an upper and rear side of a tray, and then put the disc on disc
holders in a down side of the tray.
4. Check three disc holders to confirm to the disc surely.
Page 31
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
Notes in use
(1) A disc might be scratched, damaged and dropped from a tray when used with a disc not correctly
installed. Please install correctly and use a disc.
(2) Please do drawing out (pulling return) a disc holder before setting a disc in a tray.
(3) Please do drawing out (pulling return) a disc holder with the power supply not supplied to the
drive as much as possible, because the auto-loading function might work and the tray might enter
the drive during drawing out or pulling return the disc holder.
When doing with the power supply to the drive unavoidably, work carefully holding the tray by
hand firmly.
(4) When using a drive by vertical posture, 80 mm DVD/CD cannot be used.
(5) When DVD-RAM (cartridge type) is used, the position of a disc holder need not be returned.
Page 32
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
OD-A017-02
TOSHIBA DVD-RAM SD-W1111
‘99/06/26 Version 1.0
15.3 Disc eject at emergency
Please do according to the following procedures when it is necessary to take out a disc from the drive
in the emergency.
Check that the power supply of the drive is turned off and one minute or more passes.
Insert an attached emergency eject tool in the emergency eject hole and push bumping inside. (Figure
1)
Front bezel opens a little and an inside tray rises. (Figure 2)
When the tray comes out forward, draws out it and the disc is taken out. (Figure 3)
Please draw out the tray with an emergency eject tool, when the tray does not come out. (Figure 4)
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Page 33
Product Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
Deviation List
Page
Item
Rev # 0.9a
Rev # 1.0
3
8
Cautions
---
Add (6)
Rotational speed(DVD-RAM)
Host I/F
1,130 - 2,640 rpm
ANSI ~ Rev 10k
150 ms (typ.)
1,028 – 2,400 rpm
ANSI ~ Rev 10L
170 ms (typ.)
9
Average access time
8.3 vibration
12
17
20
23
9.8 cm/s2
9.8 m/s2
10.3 Notes on mounting
12 Rear View and Connectors
12.4 Audio Connector
150 gf : 0.015N
Audio ~ CD(3 pin)
Connector chart(3 pin)
(0082 ~ Kyosera Elco
ANSI ~ Rev 10k
8 cm DVD/CD ~
1.5N : 150 gf
Audio ~ CD(4 pin)
Connector chart(4 pin)
part number ~ AMP
ANSI ~ Rev 10L
80 mm DVD/CD ~
26
32
13.1 Applicable standard
Notes in use (4)
Download from Www.Somanuals.com. All Manuals Search And Download.
|