Toshiba DVD Player SD 590KY User Manual

SD-590KY

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

18. Do not use a cracked , deformed, or repaired disc. These discs are easily broken and may cause serious personal

injury and apparatus malfunction.

19. If the apparatus should smoke or smell,immediately disconnect the power cord from the wall outlet. Wait until the

smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause ﬁre.

20. While it is thundering, do not touch the connecting cables or the apparatus.

CAUTION:

This Digital Video Disc Player employs a Laser System.

To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference

Should the unit require maintenance, contact an authorized service location.

Use of controls or adjustments or performance of procedures other than those speciﬁed herein may result in

hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open the enclosure.

Visible and invisible laser radiation when open and interlocks defeated.

DO NOT STARE INTO BEAM.

CAUTION: These servicing instructions are for use by qualiﬁed service personnel only. To reduce the risk of

electric shock do not perform any servicing other than that contained in the operating instructions unless you are

qualiﬁed to do so.

Be aware that this equipment is still powered when in standby mode. To disconnect this equipment completely from the

mains power, pull out the power plug from the wall outlet.

Environmental Information

All unnecessary packaging has been omitted. The packaging has been made easy to separate into three materials;

cardboard (box), polystyrene foam (buffer) and polyethylene (bags,protective foam sheet).

Your DVD player consists of materials which can be recycled and reused if disassembled by a specialised company.

Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old

equipment.

Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain

readily operable.

In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD video player.

Model No.

Serial No.

Retain this information for future reference.

Location of the required label:

MAINS

The rating plate and the safety caution

are on the rear of the unit.

LASER

Type

Semiconductor laser

InGaAIP(DVD)

AIGaAs(CD)

Wave length

658 nm(DVD)

790 nm(CD)

10.0 mW(DVD)

7.0 mW(VCD/CD)

Output Power

Beam divergence 60 degrees

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

CAUTION!

WARNING:

RISK OF ELECTRIC SHOCK!

Do not use solvents such as benzene, thinner,

commercially available cleaners, or anti-static sprays

intended for analog discs. Since the optical unit

(laser) of the DVD system operates at a higher

power than regular DVD or CD players, cleaning

CDs intended for DVD or CD players may damage

the optical unit (laser). Therefore, refrain from using

a cleaning CD.

Never attempt to service this product yourself.

Opening and removing the covers may expose you

to dangerous voltage or other hazards. Failure to

follow this WARNING may result in death or serious

injury. Refer all servicing not speciﬁed in this manual

to a Toshiba Authorized Service Center.

Moisture Condensation

Setup

Moisture condensation damages the DVD player.

Please read the following carefully. Moisture

condensation occurs, for example, when you pour a

cold drink into a glass on a warm day. Drops of water

form on the outside of the glass. In the same way,

moisture may condense on the optical pick-up lens

inside this unit, one of the most crucial internal parts

of the DVD player.

Finding a suitable location

-Place the set on a ﬂat, hard and stable surface.

-Do not place the set on a carpet.

-Do not position the set on top of other equipment

that might heat it up (e.g., receiver or ampliﬁer).

-Do not put anything under the set

(e.g.CDs, magazines).

-Install this unit near the AC outlet and where the

AC power plug can be reached easily.

If you use the DVD player in such a situation, it may

damage discs and internal parts. Remove the disc,

connect the power cord of the DVD player to the wall

outlet, turn on the DVD player, and leave it for two or

three hours. After two or three hours, the DVD player

will have warmed up and evaporated any moisture.

Keep the DVD player connected to the wall outlet

and moisture condensation will seldom occur.

Space for ventilation

-Place the apparatus in a location with adequate

ventilation to prevent internal heat build up. Allow at

least 10 cm (4.0'') clearance from the rear and the

top of the set and 5 cm (2.0'') from the left and right

to prevent overheating.

5cm (2.0")

10cm (4.0")

5cm (2.0")

10cm (4.0")

Region Codes

This DVD player is designed to support the Region

Management System. Check the regional code

number on the disc package. If the number does

not match the player' s region number (see table on

page 4), the player may be unable to playback the

disc.

Avoid high temperatures, moisture, water and

dust

-Apparatus shall not be exposed to dripping or

splashing.

-Do not place any sources of danger on the

apparatus (e.g., liquid ﬁlled objects, lighted candles).

Tips:

-It may not be possible to play CD-R/RW , DVD⁺R/

RW , or DVD⁺R DL in all cases due to the type of

disc or condition of the recording.

-If you are having trouble playing a certain disc,

remove the disc and try a different one. Improperly

formatted disc will not play on this DVD Player.

Cleaning discs

Some problems occur because the disc inside the

system is dirty (frozen picture, sound disruptions,

picture distortions). To avoid these problems, discs

should be cleaned on a regular basis.

To clean a disc, use a micro ﬁbre cleaning cloth

and wipe the disc from the center to the edge in a

straight line. Do not touch the playback side of the

disc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Discs that can

be played

Region

ꢀꢀꢀ

ꢁꢂꢃꢂꢄꢂꢀꢅꢆꢇꢀ

ꢈꢅꢆꢅꢇꢅꢀꢉꢊꢋꢌꢍꢆ

ALL

ꢁꢂ ꢂꢎꢀ

ꢏ"ꢉꢍꢐꢊꢀꢉꢊꢋꢌꢍꢆ ꢀꢀꢅꢆꢇ

%ꢅꢐꢅꢆ

ALL

The use of the symbol indicates that this

product may not be treated as household

waste. By ensuring this product is

ꢄ ꢌꢅꢀꢑꢅꢒꢌ$ꢀꢒꢎ

ꢓꢅꢌ#ꢅꢆꢎꢀ ꢍꢉꢊꢅ

disposed of correctly, you will help

prevent potential negative consequences

for the environment and human health,

which could otherwise be caused by

inappropriate waste handling of this

product. For more detailed information

about recycling of this product, please

contact your local city ofﬁce, your

ꢄ" !ꢉꢅꢔꢌꢅꢎ

ꢕꢊ#ꢀꢖꢊꢅꢔꢅꢆꢇꢎ

ꢗꢅ!ꢌꢆꢀꢄꢘꢊꢉꢌꢒꢅ

household waste disposal service or the

shop where you purchased the product.

ꢙ" ꢌꢅꢀꢅꢆꢇꢀ

ꢚꢆꢇꢌꢅꢀꢉꢊꢋꢌꢍꢆ

ꢈꢛꢌꢆꢅꢎꢀꢈꢅꢔꢒꢍ ꢀꢚ ꢔꢅꢆꢇ ꢎ

ꢜꢅꢔꢔ ꢀꢅꢆꢇꢀꢝ"!"ꢆꢅ

ꢚ ꢔꢅꢆꢇ

Unauthorized copying, broadcasting, public

performance and lending of discs are prohibited.

This product incorporates copyright protection tech-

nology that is protected by method claims of certain

U.S. patents and other intellectual property rights

owned by Macrovision Corporation and other rights

owners. Use of this copyright protection technology

must be authorized by Macrovision Corporation, and

is intended for home and other limited viewing uses

only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is

prohibited.

Notes on copyright

The unauthorized recording, use, distribution, or revision

of television programs, videotapes, DVDs and other

materials, is prohibited under the Copyright Laws of the

United States and other countries, and may subject you

to civil and/or criminal liability.

Helpful hint: Before making or changing any connections, make sure that all the devices are

disconnected from the power outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Table of Contents

Introduction

SAFETY PRECAUTIONS

IMPORTANT SAFETY INSTRUCTIONS

Setup

1-2

3-4

Cleaning discs

Moisture Condensation

Region Codes

Table of Contents

Connections

Connecting to television

Connecting to a Stereo System

Connecting to a Digital AV Receiver

Connecting the power cord

Product Overview

Front and Rear panels

Remote Control

Getting Started

Inserting Batteries

Finding your viewing channel

Setting up Progressive Scan feature

Setting the language

11-12

^.Playback from Disc

Playable discs

12-13

Playback Feature

Starting disc playback

13-14

14-15

Basic playback control

Operations for video playback (DVD/VCD/SVCD)

Selecting various repeat functions

Viewing the disc playback Information

Special DVD Features

Special VCD and SVCD Features

Playing a DivX Disc

Playing MP3/JPEG/Kodak picture CD

16-17

DVD menu Options

Using the Language setup menu

Using the Video setup menu

Using the Audio setup menu

Using the Rating setup menu

Using the Misc (Miscellaneous) setup menu

Tray Lock

17-19

19-20

20-21

Others

Speciﬁcations

Troubleshooting

Glossary

23-24

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

IMPORTANT!

-The progressive scan video quality is only

possible when using Y, P^B,PR and a progressive

scan TV is required.

Connecting to television

Use the component video cables (red/blue/green) to

connect the DVD player' s Y, PB, PR jacks to the

corresponding Component video input jacks (or

labelled as Y, Pb, Pr) on the TV (cable not supplied).

Use the audio cables (white/red) to connect AUDIO

OUT (L/R) jacks of the DVD player to the

corresponding AUDIO IN jacks on the TV (cable not

supplied).

IMPORTANT!

– You only need to make one video connection

from the following options, depending on the

capabilities of your television.

– Connect the DVD player directly to the

television.

Using Composite Video Jack(CVBS)

Proceed to page 11 for detailed Progressive Scan set

up.

Using a RF modulator

Use the composite video cable (yellow) to connect

the DVD player' s VIDEO(CVBS) jack to the video

input jack(or labelled as A/V in,Video In or

Composite) on the TV(cable supplied).

To hear the sound of this DVD player through your

TV, use the audio cables(white/red)to connect

AUDIO OUT(L/R)jacks of the DVD player to

corresponding AUDIO IN jacks on the TV(cable

supplied).

IMPORTANT!

-If your TV only has a single Antenna In jack (or

labelled as 75 ohm or RF In), you will need an RF

modulator in order to view the DVD playback on

the TV.

Use the composite video cable (yellow) to connect

the DVD player' s VIDEO (CVBS) jack to the video

input jack on the RF modulator (cable supplied).

To hear the sound of this DVD player through your

TV, use the audio cables(white/red) to connect

AUDIO OUT (L/R) jacks of the DVD player to the

corresponding AUDIO IN jacks on the RF modulator

(cable supplied).

Using Component Video Jacks(Y, PB, PR)

Use the RF coaxial cable (not supplied) to connect

ANTENNA OUT or TO TV jack on the RF modulator

to the ANTENNA IN jack on the television.

Connect the Antenna or Cable TV service signal to

the ANTENNA IN or RF IN jack on the RF modulator.

(It may have been connected to your TV previously.

Disconnect it from the TV.)

Helpful hint: Before making or changing any connections, make sure that all the devices are

disconnected from the power outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Connecting to a Stereo System

Connecting to a Digital AV Receiver

MAINS

Stereo system has Dolby Pro Logic or Right/Left

Audio In Jacks

Receiver has a PCM, Dolby Digital or MPEG

decoder

Select one of the video connections (CVBS VIDEO IN

or COMPONENT VIDEO IN)

depending on the options available on your TV.

Connect the COAXIAL jack of the DVD player to the

corresponding Digital Audio In jack on your Receiver

(cable not supplied).

Set the DVD Player' s Digital Output to PCM or All

depending on the capabilities of your Receiver (see

page 19 {Digital Output}).

Select one of the video connections (CVBS VIDEO

IN or COMPONENT VIDEO IN)

depending on the options available on your TV.

Use the audio cables (white/red) to connect AUDIO

OUT (L/R) jacks of the DVD Player to the

corresponding AUDIO IN jacks on the stereo system

(cable not supplied).

Tip:

-If the audio format of the Digital Output does not

match the capabilities of your receiver, the receiver

will produce a strong, distorted sound or no sound at

all.

Helpful hint: Before making or changing any connections, make sure that all the devices are

disconnected from the power outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Connecting the power cord

MAINS

After everything is connected properly, plug in the AC

power cord to the power outlet.

Never make or change any connections with the

power switched on.

Helpful hint: Before making or changing any connections, make sure that all the devices are

disconnected from the power outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Product Overview

Front and Rear panels

#ꢀ9ꢁPLAY/ PAUSE

-Starts or pauses playback

I/2ON/STANDBY

-Turns the player on or switches it to

standby mode

^ꢁSTOP

- Stops playback

Disc tray

^çOPEN/CLOSE

- Place a disc here

- Opens or closes the disc tray

Display

- Shows information about the current status

of the DVD Player

IR Sensor

- Points the remote control towards this sensor

MAINS ~

- Connects to a standard AC outlet

AUDIO OUT (Left/Right)

- Connects to Audio input of a TV, an ampliﬁer,

receiver or stereo system

Y, PB, PR Component Video Out

- Connects to Y, PB, PR input of a TV

COAXIAL(Digital audio out)

- Connects to coaxial Audio input of a digital audio

equipment

VIDEO Out (CVBS)

- Connects to CVBS Video input of a TV

DVD display

The indicators vary depending on the kinds of disc

you play.

DVD video disc

VIDEO CD

•During playback:

Example

Audio CD

•During playback:

Example

Chapter/Track

•During playback:

Example

number indicator

Some discs may only Some discs may only Some discs may only

display chapter

numbers.

display track

numbers.

display track

numbers.

Multifunctional indicator (indicates

operating status or messages, etc.)

OPEN

LOAD/CLOSE

No disc

Bad disc

ꢀ"----" may also appear in other situation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Product Overview

Remote Control

See the page in [ ] for details.

REMOTE SIGNAL EMITTER

[ 15 ]

DISPLAY

[ 11 ]

-Displays information on

-Point remote control to the sensor on

the front panel

TV screen during playback

[ 11, 13 ]

ON / STANDBY

[ 13 ]

OPEN/CLOSE

-To switch the DVD player to ON or

standby mode

-Open/close the disc tray

[ 13, 15, 20 ]

Number Buttons

-Selects numbered items in a menu

[ 15 ]

T - SEARCH

-Start playback from a designated

point

-Press to enter track/chapter/title

numbers or password directly

[ 11, 17 ]

SETUP

-Enters or exits the system setup

[ 14 ]

+10 button

-Press to enter number greater than 9

-Press +10 button repeatedly to select

10,20,30...etc

ꢀꢁꢂꢃ[ 14, 16, 17 ]

-Cursor buttons for moving to the left

/ right / up / down

-To rotate the JPEG picture during

playback

[ 14, 15 ]

-Enters or exits the disc menu

-Switches on or off the Playback

Control (PBC) mode (for VCD 2.0 /

SVCD only)

STEP

-Play video frame by frame

[ 13, 14 ]

PLAY/PAUSE

-Starts or pauses playback

[ 12 ]

-Acknowledge menu selection

[ 14 ]

ꢁ

STOP

-Stops play

[ 15 ]

RETURN

-To go back to previous menu

[ 15 ]

SUBTITLE

-To access subtitle language

TITLE

-Show title menu

[ 15 ]

ANGLE

-Switch the camera angle during

playback

[ 15 ]

AUDIO

[ 14 ]

F.R & F.F

-Selects an audio setting (DVD) or an

audio channel (VCD)

-Do a forward/reverse search

[ 13, 15, 16 ]

PREV & NEXT

-Skip to previous / next chapter /track

[ 14, 17 ]

ZOOM

-Enlarge a picture on the TV

[ 14 ]

REPEAT

-Selects various repeat mode

[ 16 ]

RANDOM

-Toggles between Normal and Shufﬂe

playback

[ 15 ]

A-B

-Repeats playback from point A to B on

a disc

[ 14 ]

PROG

-To program playback or cancel the

program playback

[ 14 ]

SLOW

-Do a slow forward

[ 14 ]

CLEAR

-Delete the mistyped entries or cancel

some functions

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Started

and highest channels and may be called FRONT,

A/V IN or VIDEO. See your TV' s manual for more

details.

Inserting Batteries

ꢂOr, you may go to channel 1 on your TV, then

press the Channel down button repeatedly until you

see the Video In channel.

ꢂOr, the TV remote control may have a button that

chooses different video modes.

ꢂOr, tune the TV until you can see the DVD player

signal from the RF modulator (refer to your TV user

manual).

If you are using external equipment, (such as

audio system or receiver), turn it on and select the

appropriate input source for the DVD player output.

Refer to the equipment user’s manual for detail.

Open the battery compartment.

Insert two batteries type R03 or AAA, following the

indications (+ / - ) inside the compartment.

Close the cover.

Setting up Progressive Scan feature

CAUTION:

Never throw batteries into a ﬁre.

Note:

(For Progressive Scan TV only)

- Be sure to use AAA size batteries.

- Dispose of batteries in a designated disposal area.

- Batteries should always be disposed of with the

environment in mind. Always dispose of batteries in

accordance with applicable laws and regulations.

The progressive scan display twice the number

of frames per seconds than interlaced scanning

(ordinary normal TV system). With nearly double

the number of lines, progressive scan offers higher

picture resolution and quality.

- If the remote control does not operate correctly, or if

the operating range becomes reduced, replace batteries

with new ones.

- When necessary to replace batteries in the remote

control, always replace both batteries with new ones.

Never mix battery types or use new and used batteries

in combination.

- Always remove batteries from remote control if they

are dead or if the remote control is not to be used for an

extended period of time. This will prevent battery acid

Before you start...

-Ensure that you have connected this DVD player

to a progressive scan TV using the Y, PB, PR

connection (see page 6).

-Ensure that you have completed the basic

installation and set up.

Turn on your TV and select the video input

connected to the DVD player (refer to your TV user

manual).

Press 2ON/STANDBY on the remote control to turn

on the DVD player.

ꢂThe blue DVD background screen will appear on

the TV.

Press SETUP.

Press ꢂ/ꢃto select { Video }, then press ꢁ.

from leaking into the battery compartment.

Using the Remote Control to Operate

the System

Aspect Ratio

: 4:3

Language

Video

View Mode

TV System

Video Out

:Auto Fit

:PAL

Within about 6m (19 feet)

Component

P-Scan

OPEN/CLOSE DISPLAY

ON/STANDBY

Smart Picture

Audio

ꢀ

ꢅ

ꢁ

ꢄ

ꢂ

ꢃ

Rating

Misc

Aim the Remote Control directly at the remote sensor

(IR) on the front panel.

Do not put any objects between the Remote Control

and DVD Player while operating the DVD Player.

Press ꢂ/ꢃto select { Video Out }, then press ꢁ.

Select { P- Scan }, then press OK to conﬁrm.

ꢂThe menu will appear on the TV.

Video Out

Finding your viewing channel

Activating Progressive Scan 1. Ensure

your TV supports Progressive Mode

2. If there is a distorted picture on the

TV, wait 15 seconds for automatic

recover

Press I/2ON/STANDBY on the DVD player to turn it

on.

Turn on the TV and set it to the correct video-in

channel. You should see the blue DVD background

screen.

Yes

ꢂUsually these channels are between the lowest

Helpful hint: Press ꢀto go back to previous menu item.

Press SETUP to exit the menu item.

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Started/Playback from disc

soundtrack from audio, subtitles and DVD menu

languages. If the language selected is not available

on the disc, the disc’s default language will be used

instead.

Press ꢀto highlight { Yes } and press OK to conﬁrm.

ꢂThe reconﬁrmation menu will appear on the TV.

Video Out

Confirm again to use new setting

OSD language : English

Language

Subtitle

: Auto

Yes

DivX Subtitle

Audio

: Standard

English

Video

Audio

Press ꢀto highlight { Yes } and press OK to conﬁrm.

ꢂThe setup is now completed and you can start

enjoying the high quality picture.

DVD Menu

Persian

Arabic

Rating

Misc

Russian

Indonesian

To deactivate Progressive Scan

manually:

Wait for 15 seconds for the auto recovery.

Press SETUP.

Press ꢂ/ꢃto select { Language }, then press ꢁ.

Press ꢂ/ꢃto highlight one of the options below,

then press ꢁ.

Press OPEN/CLOSE çon the DVD player to open

the disc tray.

Press number button ' 1 ' on the remote control for a

few seconds.

ꢂThe DVD background screen appears.

{ Subtitle }

Select this to change the subtitle language.

{ Audio }

Select this to change the disc soundtrack language.

{ DVD Menu }

Tip:

Select this to change the language of the disc menu.

Use ꢂ/ꢃto select a language and press OK to

conﬁrm.

-There are some progressive scan TVs and High-

Deﬁnition TVs that are not fully compatible with this

unit, resulting in the unnatural picture when playing

back a DVD VIDEO disc in the progressive scan

mode. In such a case, turn off the progressive scan

feature on both the DVD player and your TV.

Repeat steps C - D for other language settings.

IMPORTANT!

- DVD discs and players are designed with regional

restrictions. Before playing a disc, make sure the

disc is for the same zone as your player.

Setting the language

-If '

'appears on the TV screen when a button is

pressed, it means the function is not available on

the current disc or at the current time.

Choose your desired On-Screen Display(OSD)language

where available.

On-Screen Display (OSD) Language

Playable discs

The On-screen language for the system setup menu

will remain as you set it, regardless of various disc

languages.

Using this DVD player, you can playback on the

following discs. Some of these discs may be

incompatible.

DVD Video disc(Digital Versatile Disc)

DVD⁺R/RW (DVD Recordable / Re-

writable), DVD⁺R DL (Dual layer)

Audio/Video formats or MP3/

JPEG ﬁles.

Press SETUP.

Press ꢂ/ꢃto select { Language }

Press ꢁto highlight { OSD language }, then press

ꢁ.

CD-R (CD-Recordable)

Audio/Video format or

MP3/JPEG ﬁles.

Press ꢂ/ꢃto select a language and press OK.

Audio, Subtitle and DVD menu

language

You can choose your own preferred language or

Helpful hint: Press ꢀto go back to previous menu item.

Press SETUP to exit the menu item.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback from disc/Playback Feature

CD-RW (CD-Rewritable)

Audio/Video format or

MP3/JPEG ﬁles.

-Q-pel accurate motion compensation.

Global Motion Compensation (GMC) playback.

-Ofﬁcial DivX^®Certiﬁed product.

-Plays all versions of DivX^®video (including DivX^®6)

with standard playback of DivX^®media ﬁles.

Audio CD (Compact Disc

Digital Audio)

Tips:

– Maximum 100 sessions for CD and 10 multi border

for DVD are supported.

Video CD

(Formats 1.0, 1.1, 2.0)

– For DVD-R, DVD-RW multi border, only finalized

disc can be supported.

– For DVD+R and DVD+RW multi border, both

ﬁnalized and unﬁnalized disc cannot be supported.

Super Video CD

MP3-Disc

Starting disc playback

Turn on the TV and select the video input connected

to the DVD player.

is a trademark of DVD Format/Logo Licensing

Corporation.

Press 2ON / STANDBY to turn on the DVD player.

Press OPEN/CLOSE to open the disc tray.

Place a disc onto the disc tray with the label facing

up, then press OPEN/CLOSE.

Because of problems and errors that can occur

during the creation of DVD and CD software and/or

the manufacture of DVD and CD discs, Toshiba

cannot assure that this DVD player will successfully

play every disc bearing the DVD and CD logos. If you

happen to experience any difficulty playing a DVD

and/or CD disc on this DVD player, please contact

Toshiba Customer Service.

ꢂFor double-sided discs, load the side which you

want to play facing up.

Playback may start automatically. If not, press PLAY/

PAUSE

ꢂIf a disc menu appears on the TV, see page 14

'Using the disc menu'.

This DVD player requires discs/recordings to meet

certain technical standards in order to achieve

optimal playback quality. There are many different

types of recordable disc formats (including CD-R

containing MP3 files). Not all recordable discs will

operate or produce optimal playback quality. The

technical criteria set forth in this owner's manual are

meant only as a guide. Use of CD-RW for MP3 ﬁles

is not recommended.

ꢂIf the parental control was activated for the

inserted disc, you have to enter your four-digit

password, see page 20.

ꢂFor more playback features, see pages 13 - 17.

Tips:

-Do not overturn the DVD player while disc loading,

playing or ejecting.

-Do not close the disc tray manually even if the

power is switched off.

You must obtain any required permission from

content. Toshiba cannot and does not grant such

permission.

Basic playback control

Supported Formats

MP3 tracks

Unless otherwise stated, all operations described are

based on Remote Control use.

-The ﬁle extensions has to be '.mp3 '.

-JPEG/ISO format.

Pausing playback

During playback, press PLAY/PAUSE

playback and display a still picture.

ꢂSound will be muted.

To resume normal playback, press PLAY/PAUSE

again.

to pause

-Maximum 8 characters display for folder name.

-Maximum 15 characters display for ﬁle name.

-Supported sampling frequencies & corresponding

bit-rates;

32kHz, 64-320 kbps

44.1kHz, 48kHz 80-320 kbps

JPEG/Pictures

Skipping chapter/track

ꢀPress PREV

/ NEXT

to go to the previous

-The ﬁle extensions has to be '.JPG ' and not

'.JPEG' .

or next chapter/track during playback.

-JPEG/ISO format.

ꢂWhen PREV

is pressed after the ﬁrst 5

-Maximum of 5760×3840 resolution can be

supported.

seconds of playback, playback will start from the

beginning of the current chapter/track. If you press

the button within the ﬁrst 5 seconds, playback will

start from the beginning of the preceding chapter/

track.

ꢀPress DISPLAY to display the disc

information for title/chapter/track.

-Maximum ﬁle size: 10M.

-It can only display DCF-standard still pictures or

JPEG pictures such as TIFF.

DivX

-The ﬁle extensions has to be '.AVI ', '.MPG ' or

'.MPEG '.

ꢀUse Number buttons to enter valid chapter / track

number directly. For the track/chapter numbers which

-DivX^®3.11, 4.x, 5.x and 6.0.

Helpful hint: Some discs cannot be played on this DVD player due to the conﬁguration and characteristics

of the disc, or due to the condition of recording and authorizing software

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback Feature

are greater than

presses increases the number by 10. Then press the

second digit of track/Chapter number.

, use +10 button. Each

TV screen once you load in the disc.

To select a playback feature or item

Use ꢀ/ꢁ/ꢂ/ꢃor number buttons on the remote

ꢀ

ꢂThe playback skips to the selected chapter / track.

control, then press OK to start playback.

To access or remove the menu.

Stopping playback

Press MENU on the remote control.

ꢀ

ybac

During playback, press STOP

ꢁ

Zooming In

The DVD player memorises the stopped point.

ꢀ

Press PLAY/ PAUSE

location where you stopped playback.

If you press STOP again, the DVD player will

cancel the resume function.

Tips:

-Screen saver will start automatically if the disc

playback is stopped for about 2 minutes.

-The player will automatically switch to Power

Standby mode if you do not press any buttons for

about 22 minutes after the disc has stopped playing.

to resume playback from the

This function allows you to enlarge the picture on the

TV screen and to pan through the enlarged picture.

ꢀ

ꢁ

During playback, press ZOOM repeatedly to display

the picture with different scales.

ꢀUse ꢀ/ꢁ/ꢂ/ꢃto pan through the enlarged picture.

ꢀPlayback will continue.

Press ZOOM repeatedly to return to the original size.

Slow Motion

Program playback

Press SLOW during playback to select the required

speed: 1/2, 1/4, 1/8( forward only ).

During playback, press PROG, then the OSD will

appear as below:

ꢂSound will be muted.

To return to normal speed, press PLAY/ PAUSE

For VCD:

Program

Forward/ Reverse Searching

Track 1

Track 2

Track 3

Track 4

You can fast forward or fast reverse a disc during

playback and select a desired search speed.

For DVD,VCD, SVCD,CD, MP3

During playback, press F.R/ F.F to select the required

speed: X2, X4, X8, X16(backward or forward).

ꢂSound will be muted (DVD/VCD/SVCD/MP3) or

Track 5

Track 6

Clear

Play

Clear All

intermittent (CD).

To return to normal speed, press PLAY / PAUSE

For DVD:

Program

Selecting various repeat functions

Repeat play mode

Title 1

Title 2

Title 3

Title 4

The repeat play options vary depending on the disc

type.

While playing a disc, press REPEAT repeatedly to

choose a repeat options.

Clear

Play

Clear All

Use the ꢂ/ꢃand OK button to select your desired

For DVD

title/chapter/track in the list.

-Repeat Chapter (currently playing chapter)

-Repeat Title (currently playing title)

-Off (cancel)

When you have ﬁnished programming, press ꢁto

move the cursor to the 'Play', then press the OK

button or directly press PLAY/PAUSE

start the program playback.

button to

For Video CD, Audio CD

-Repeat Single (currently playing track)

-Repeat All (entire disc)

-Off (cancel)

Press CLEAR or select ' Clear ' to delete one by one

from last chosen track / title /chapter or select 'Clear

All' to clear all the programmed tracks/titles.

Press STOP twice to cancel program playback.

For MP3, JPEG

-Repeat Single (currently playing ﬁle)

-Repeat All (current folder)

-Off (cancel)

Operations for video playback (DVD/

VCD/SVCD)

Tip:

Using the disc menu

-For VCD2.0/SVCD discs, repeat playback is not

possible if the PBC mode is turned on.

Depending on the disc, a menu may appear on the

Helpful hint The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the discs.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback Feature

Repeating a section within a chapter/

Angle

track

When {Angle} information appears on the screen,

ꢀ

You can repeat the playback of a speciﬁc segment

within a chapter or track. To do this, you must mark

the start and end of the segment you want.

press ANGLE button on the remote control

repeatedly to switch between different angles.

Playback will go to the selected angle.

ꢂ

While playing a disc, press A - B at your chosen

starting point.

Press A - B again at your chosen end point.

Special DVD Features

ꢂThe section will now repeat continuously.

To exit the sequence, press A - B.

Playing a Title

Press TITLE.

Viewing the disc playback Information

ꢂThe disc title menu appears on the TV screen.

Use ꢂ/ꢃ/ꢀ/ꢁor number buttons (0-9) to select a

play option.

Press OK to conﬁrm.

Changing the Audio Language

You can view the disc information (such as current

title/chapter/track number, total playing time or

remaining time on the disc) without interrupting the

disc playback.

For DVD

During playback, press DISPLAY repeatedly on the

remote control.

ꢂThe available disc information appears on the TV

screen with the following sequence.

Press AUDIO repeatedly to select different audio

languages.

Changing the Audio Channel

For VCD

Time

Title

Press AUDIO to select the available audio channels

ꢀ

(DVD)

00 03 33/01 24 46

provided by the disc (Left, Right, Mix, Stereo).

Subtitles

Title 1/1

Chapter

Chapter 2/8

Audio

Press SUBTITLE repeatedly to select different

ꢀ

subtitle languages.

Audio 1/1

Subtitle

D 6Ch Eng

(DVD)

(VCD)

Special VCD and SVCD Features

Subtitle

1/8 Eng

Angle

Angle 1/4

For VCD with Playback Control ( PBC ) feature

(version 2.0 only)

ꢀPress MENU to toggle between ' PBC On ' and '

PBC Off '.

ꢂIf you select ' PBC On ', the disc menu ( if

available ) will appear on the TV.

ꢂUse the number buttons ( 0-9 ) to select a play

option.

Time

00 03 33/00 05 00

3/24

Track

(VCD PBC OFF)

Time

(VCD PBC ON)

Time

PBC On

00 03 33/00 05 00

ꢀPress PREV

or next track.

ꢂWhen PREV

/ NEXT

to go to the previous

Title/Chapter/Track/Time selection

is pressed after the ﬁrst 5

seconds of playback, playback will start from the

beginning of the current track. If you press the button

within the ﬁrst 5 seconds, playback will start from the

beginning of the preceding track.

ꢀDuring playback, pressing RETURN will return to

the menu screen (if PBC is on).

If you want to skip the index menu and playback

directly from the beginning.

ꢀPress MENU on the remote control to turn the PBC

off.

Press T-SEARCH, then press ꢂ/ꢃto select

{ Time }, { Title }, { Chapter } or { Track }.

For VCD

PBC OFF

Track

---

Time

--:--:--

(desired time of the current track)

(desired time of the disc)

Disc Time

For DVD:

Title

---

Chapter

Time

--:--:--

(desired time of the disc)

Use the number buttons ( 0-9 ) to input a valid

number or time ("0" cannot be input as the ﬁrst

number). (This function only apply to DVD/VCD.)

Press OK to conﬁrm.

ꢂThe playback skips to the selected title/chapter/

track/time.

Helpful hint The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the discs.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback Feature

Playback Selection

During playback, you can;

ꢀPress PREV / NEXT

previous/next track/ﬁle in the current folder.

ꢀPress PLAY/PAUSE

resume playback.

For MP3

Playing a DivX Disc

to select the

This DVD player supports the DivX^®movie playback

that you download from your computer onto a CD-

R/RW or DVD+R/RW (see pages 12-13 for more

information).

repeatedly to pause/

Load a DivX^®disc.

ꢀWithin the ﬁrst 5 seconds, press PREV

back to the previous track.

to go

The data disc menu appears on the TV screen.

Press ꢂ/ꢃto select the folder and press OK to

open the folder.

ꢀAfter the ﬁrst 5 seconds of playback, press PREV

to go back to the beginning of current track.

Press ꢂ/ꢃto select a ﬁle.

Press OK to conﬁrm.

ꢀDuring playback, press

forward or fast reverse with the required speed: X2,

X4, X8, X16.

to access fast

ꢀPress SUBTITLE on the remote control will turn

on or off the subtitle.

ꢀIf multilingual subtitles are embedded on the DivX^®

disc, pressing SUBTITLE will change the subtitle

language during playback.

Play modes for DivX /MP3/Audio

CD/JPEG

You are able to modify the play modes through the

toolkit which appears on the right of below picture

on the screen. Press ꢀ/ ꢁto navigate between the

windows and ꢂ/ ꢃbuttons to select ﬁles/ tracks or

play mode items. Then press OK . Please refer to

below steps to playback ﬁles /tracks in the Program

View list:

Tips:

–Subtitle ﬁles with the following ﬁlename extensions

(.srt, .smi, .sub, .ssa, .txt) are supported but do not

appear on the ﬁle navigation menu.

–The subtitle ﬁlename(.sub) has to be saved under

the same ﬁlename as the movie(.avi) in the same

folder.

[For example, Folder A: abc.avi and abc.sub]

Select Edit Mode in the toolkit then press OK to

start edit mode.

Select a ﬁle/track or more ﬁles/tracks you want in the

original view list.

Select Add To Program in the toolkit then press

OK. ^'√ ' will disappear from screen. It means that the

ﬁles/tracks you have selected already added into the

Program View list.

Select Program View in the toolkit then press OK to

open the ﬁle/track in the Program View list that you

already selected in step B.

Playing MP3/JPEG/ Kodak picture CD

IMPORTANT!

You have to turn on your TV and set to

the correct Video In channel. (See page

11, ‘ Finding your viewing channel ‘ ).

General Operation

Press PLAY / PAUSE

in the Program View list.

to playback all ﬁles/tracks

Load a disc.

ꢂThe disc reading time may exceed 30 seconds

due to the complexity of the directory/ﬁle

conﬁguration.

Filter

ꢂThe data disc menu and ID3 (MP3) information

(including at least title, singer and album) appears

on the TV screen.

The Toolkit has the following play mode items:

Filter

ꢀFilter ( Audio/Photo/Video ): Sets ﬁle ﬁlters

(Filter is not applicable to Audio CD.)

ꢀRepeat (Off/Single/ All):

Off:

Resumes normal playback

Single: Repeats the current track/ﬁle.

Press ꢂ/ ꢃto select the folder and press OK to

All:

Repeats all ﬁles on the current folder or all

tracks on the disc.

open the folder.

Press ꢂ/ ꢃto select a track/ﬁle.

Press OK to conﬁrm.

ꢀMode(Normal/Shufﬂe)

This mode can also be toggled by using RANDOM

button.

Tips:

Normal: Resumes Normal playback

Shufﬂe: Playbacks track/ﬁle in random order.

ꢀEdit Mode: Program operation works only when

Edit Mode is selected. After ﬁnished storing the ﬁles/

tracks you want into the Program View list, select

“Edit Mode” again and press OK to release edit

- If you highlight on a jpeg ﬁle, a preview will appear.

- During MP3 playback, the LED will display the track

number.

- During JPEG playback, the LED will display the ﬁle

number.

Helpful hint The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the discs.

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Menu Options

mode.

OSD Language

This menu contains various language options for the

language displayed on the screen.

ꢀProgram View: To view tracks/ﬁles in the

Program View list. It is disabled if the Program View

list is empty.

ꢀAdd To Program: Add ﬁles/tracks to the Program

View list. It is disabled if Edit Mode is not selected.

(The maximum number of ﬁles/tracks can be added

is 30.)

ꢀBrowser View: To view ﬁles/tracks in the Original

View list.

Subtitle/Audio/DVD Menu/DivX

Subtitle

These menus contains various language options for

audio, subtitle, DVD menu and DivX^®subtitle which

may be recorded on the DVD.

ꢀClear Program: Delete the ﬁles/tracks in the

Program View list.

Tips:

-Some DVD video discs may be set to display

subtitles in a different language other than

you selected. A prior subtitle language may be

programmed on the disc.

-Some DVD video discs allow you to change subtitle

selections only via the disc menu. If this is the case,

press the MENU button and choose the appropriate

subtitle language from the selection on the disc

menu.

-Some DVD video discs may not be played in a

different audio language that you selected. A prior

language may be programmed on the disc.

-Some DVD discs may not include your pre-selected

language . In this case, the DVD player

automatically displays discs menus consistent with

the disc’s initial language setting.

ꢂSelect a ﬁle/track or more you want to delete in

stop mode.^'√ ' will appear besides the deleted ﬁle/

track.Select Clear Program and then press OK . It is

disabled if Edit mode is not selected.

Zoom picture ( JPEG)

ꢀDuring playback, press ZOOM repeatedly to

display the picture with different scales.

ꢀUse ꢂ/ ꢃ/ ꢀ/ ꢁto view the zoomed picture.

Rotate picture (JPEG)

ꢀDuring playback, press ꢂ/ ꢃ/ ꢀ/ ꢁto rotate the

picture on the TV screen.

ꢂ/ ꢃ ﬂip the picture vertically by 180º

ꢀ rotate the picture anti-clockwise by 90º

ꢁ rotate the picture clockwise by 90º

Tip:

-It may not be possible to play certain MP3/JPEG

disc due to the conﬁguration and characteristics of

the disc or condition of the recording.

DivX Subtitle

If your DivX^®ﬁles include a subtitle ﬁle (see page

16 for the supported ﬁle formats), you may select a

supported DivX^®subtitle language by region.

This DVD Player setup is carried out via the TV,

enabling you to customise the DVD player to suit

your particular requirement.

In ‘Language’, press ꢂ/ꢃto select

{ DivX Subtitle }, then press ꢁ.

{ Standard }

Albanian, Danish, Dutch, English, Finnish, French,

Gaelic, German, Italian, Kurdish (Latin), Norwegian,

Portuguese, Spanish, Swedish and Turkish.

Using the Language setup menu

{ Central European }

Albanian, Croat, Czech, Dutch, English,

German, Hungarian, Irish, Polish,

Press SETUP on the remote control.

ꢂThe system setup menu appears.

OSD language

Subtitle

:English

:Auto

Language

Video

Romanian, Slovak, Slovene and Sorbian.

{ Cyrillic }

Bulgarian, Belorussian, English,

Macedonian, Moldavian, Russian,

Serbian and Ukrainian.

{ Greek }

English and Modern Greek only.

{ Hebrew }

English and Modern Hebrew only.

DivX Subtitle

Audio

:Standard

English

Audio

DVD Menu

Rating

Misc

Press ꢂ/ ꢃto select { Language }, then press ꢁ.

Press ꢂ/ ꢃto select an item, then press ꢁto

access.

Example: { OSD language }

ꢂThe options for the selected item appears.

ꢂIf the selection in the menu is greyed out, that

means the feature is not available or not possible to

change at the current state.

Use ꢂ/ꢃto select a setting and press OK to

conﬁrm.

Example: { English }

Use ꢂ/ꢃto select a setting and press

OK to conﬁrm.

Using the Video setup menu

Press SETUP on the remote control.

ꢂThe system setup menu appears.

ꢂThe setting is selected and setup is completed.

To exit, press SETUP.

Helpful hint: Press ꢀto go back to previous menu item.

Press SETUP to exit the menu item.

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Menu Options

Language

4:3

Aspect Ratio

View Mode

TV System

Video Out

: 4:3

TV System

The video standard of the DVD player output can be

selected from “NTSC”, “PAL” or “Multi”.

:Auto Fit

:PAL

Video

Audio

:Component

:Standard

Smart Picture

{ NTSC }: Select if your TV system is NTSC.

{ PAL }: Select if your TV system is PAL.

{ Multi }: The DVD video player automatically

identiﬁes PAL or NTSC video system of a disc.

Connect a multisystem TV (PAL/NTSC compatible) to

view a picture.

A playback picture may be distorted when detected a

signal change between PAL and NTSC on the disc.

For the case of Progressive mode, your multisystem

TV must be able to support 525p and 625p.

Rating

Misc

Press ꢂ/ ꢃto select { Video }, then press ꢁ

Press ꢂ/ ꢃto select an item, then press ꢁto

access.

Example: { Video Out }

ꢂThe options for the selected item appears.

ꢂIf the selection in the menu is greyed out, that

means the feature is not available or not possible to

change at the current state.

Use ꢂ/ ꢃto select a setting and press OK to

conﬁrm.

Example: { P-Scan }

Video Out

The video output of the DVD player can be selected

as “Component” or “P-Scan”.

In ' Video ', press ꢂ/ ꢃto select { Video Out },

then press ꢁ.

{ Component }

Select this for component video connection.

{ P-Scan }

Select this when you connect your DVD player to

your TV, which has component video inputs that

supports progressive scan.

Use ꢂ/ ꢃto select a setting and press OK to con-

ﬁrm.

ꢂThe setting is selected and setup is completed.

To exit, press SETUP.

Aspect Ratio

The picture shape can be adjusted to ﬁt your TV and

the format must be available on the playback disc.

Otherwise, the TV display will not affect the picture

during playback.

In ' Video ', press ꢂ/ ꢃto select { Aspect Ratio },

then press ꢁ.

Smart Picture

{ 4:3 }

This DVD player provides four predeﬁned sets of

picture color settings.

In ' Video ', press ꢂ/ ꢃto select {Smart Picture },

then press ꢁ.

{ Standard }

Select this for a preset standard picture setting.

{ Vivid }

Select this to make the picture brighter.

{ Cool }

Select this to make the picture softer.

Select this if you have a normal TV. A 'wide-screen'

source display with black bars on the top and bottom

will be displayed on the TV screen.

{ 16:9 }

Select this for wide-screen TV (frame ratio 16:9).

Use ꢂ/ ꢃto select a setting and press OK to

conﬁrm.

View Mode

Use view mode to scale an image that ﬁts to the TV

screen's width and height.

In ' Video ', press ꢂ/ ꢃto select { View Mode },

then press ꢁ.

{ Fill }

{ Personal }

Select this to personalize your picture color by

adjusting the brightness, contrast, tint and color

(saturation).

Use ꢂ/ ꢃto select a setting and press OK to

Fill the screen with decoded image.

conﬁrm.

{ Original }

If you select { Personal }, then proceed to steps

Display image as its original size.

D~G.

{ Height Fit }

Fit the screen height with image height.

{ Width Fit }

ꢂThe setup menu appears.

Brightness

Fit the screen width with image width.

Contrast

{ Auto Fit }

Tint

Automatically display the decoded image on screen

Color

at a suitable size.

{ Pan Scan }

Press ꢂ/ ꢃto highlight one of the following options.

Brightness

Increase the value to brighten the picture or vice

versa. Choose zero (0) for average setting.

Contrast

Increase the value to sharpen the picture or vice

versa. Choose zero (0) to balance the contrast.

Tint

Automatically display decoded image on full screen

without distortion.

Use ꢂ/ ꢃto select a setting and press OK to

conﬁrm.

Tip:

-Depending on the type of disc, you may not be able

to view the mode as selected.

Helpful hint: Press ꢀto go back to previous menu item.

Press SETUP to exit the menu item.

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Menu Options

Increase the value to darken the picture or vice

versa. Choose zero (0) for average setting.

Color

Increase the value to enhance the colour in your

picture or vice versa. Choose zero (0) to balance the

colour.

Press ꢀ/ ꢁto adjust the setting that best suits

your personal preference.

Repeat steps D~ E to adjust your picture

preference.

Night Mode

This mode optimizes playback of sound at low

volume. High volume outputs will be softened and

low volume outputs are brought upward to an audible

level.

In Audio , press ꢂ/ ꢃto select { Night Mode },

then press ꢁ.

{ On }

Select this to set low volume output. This feature

is only available for movie discs with Dolby Digital

Press ꢂ/ ꢃto select Close and press OK to

conﬁrm.

mode.

{ Off }

Turns off night mode feature. Select this to enjoy the

Using the Audio setup menu

surround sound with its full dynamic range.

Use ꢂ/ ꢃto select a setting and press OK to

conﬁrm.

Press SETUP on the remote control.

ꢂThe system setup menu appears.

Down Sampling

You can enable and disable the digital signal for

better sound output quality.

In Audio , press ꢂ/ ꢃto select { Down

Sampling }, then press ꢁ.

{ Off }

If your ampliﬁer / decoder is compatible with 96 KHz

PCM, select “ Off “ . Sound is sampled at 96 KHz.

{ On }

: All

Digital Output

Language

Off

Night Mode

Video

Off

Down Sampling

3D Effects

Audio

Rating

Misc

If your ampliﬁer / decoder is not compatible with 96

KHz PCM, select “ On “ . Sound recorded at 96 KHz

is down sampled to 48 KHz.

Use ꢂ/ ꢃto select a setting and press OK to

conﬁrm.

Tip:

- When playing back disc with copyright protection,

the sound will be down sampled to 48 KHz even

when you select Down Sampling off.

Press ꢂ/ ꢃto select { Audio }, then press ꢁ.

Press ꢂ/ ꢃto select an item, then press ꢁto

access.

Example: { Night Mode }

ꢂThe options for the selected item appears.

ꢂIf the selection in the menu is greyed out, that

means the feature is not available or not possible to

change at the current state.

Use ꢂ/ ꢃto select a setting and press OK to

conﬁrm.

Example: { On }

3D Effects

To obtain expansive virtual surround sound effects

from two speakers, set 3D Effects to on. This

enhancement sounds only output from the Analogue

AUDIO OUT (L / R) jacks of the DVD player.

In 'Audio', press ꢂ/ ꢃto select { 3D Effects }, then

press ꢁ.You can set to { Off } or { On }.

Use ꢂ/ ꢃto select a setting and press OK to

conﬁrm.

ꢂThe setting is selected and setup is completed.

To exit, press SETUP.

Digital Output

Select this if you connect to a multichannel decoder/

receiver.

In 'Audio', press ꢂ/ ꢃto select { Digital Output },

then press ꢁ.

Tip:

{ All }

- Only effective in playback of a DVD Video disc with

Dolby Digital 5.1 bitstream.

Select this if the connected device has a built-in

multichannel decoder that supports one of the

multichannel audio format (Dolby Digital, DTS).

{ PCM }

Using the Rating setup menu

Select this if the connected device is not capable of

decoding multichannel audio. The DVD player will

convert the Dolby Digital signal to PCM (Pulse Code

Modulation).

Press SETUP on the remote control.

ꢂThe system setup menu appears.

{ Off }

Parental control

: 8.Aduit

Language

Video

Set Password

To deactivate the digital audio output. For example, if

you use the AUDIO OUT jacks to connect to a TV or

stereo system.

Audio

Use ꢂ/ ꢃto select a setting and press OK to

conﬁrm.

Tip:

Rating

Misc

-When playing MPEG, MP3 and set Digital Output to

{All}, the player will output PCM signals.

Press ꢂ/ ꢃto select {Rating }, then press ꢁ.

Helpful hint: Press ꢀto go back to previous menu item.

Press SETUP to exit the menu item.

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Menu Options

Press ꢂ/ ꢃto select an item, then press ꢁto

access.

Changing the Password

You need to enter your four-digit password to play a

prohibited disc or if prompted for a password.

In Rating , press ꢂ/ ꢃto select {Set Password

}, then press OK.

Example: { Parental control }

ꢂThe options for the selected item appears.

ꢂIf the selection in the menu is greyed out, that

means the feature is not available or not possible to

change at the current state.

Use ꢂ/ ꢃto select a setting and press OK to

conﬁrm.

Example: { 8 Adult }

ꢂYou will be prompted to enter your four-digit

password.

Enter Password

ꢂThe setting is selected and setup is completed.

To exit, press SETUP.

Use the number buttons ( 0-9 ) to enter the four-digit

password.

Rating Level settings

ꢂWhen doing this for the ﬁrst time, enter the default

password 0000

Depending on the DVD, you may be asked to

change the parental level while playing the disc. The

rating levels are from 1 to 8 and are country

dependent. You can prohibit the playing of certain

discs that are not suitable for your children, or have

certain discs played with alternative scenes.

In ' Rating ', press ꢂ/ ꢃto select {Parental control },

then press ꢁ.

ꢀIf you forget your old four-digit password, enter the

default password

0000

Press OK again to enter the new four-digit password.

ꢂThe new four-digit password will now take effect.

Enter New Password

Press OK to conﬁrm.

Use the number buttons to enter the four-digit

password, then press OK.(See ‘Changing the

Password’ on this page.)

Using the Misc (Miscellaneous) setup

Press OK again to list the parental level.

{ 1.Kid Safe }

Suitable for children.

{ 2. G }

Press SETUP on the remote control.

ꢂThe system setup menu appears.

General Audience; recommended as acceptable for

viewers of all ages.

Use Default Settings

DivX Registration

Language

Video

{ 3. PG }

Parental Guidance suggested.

{ 4. PG-13 }

Audio

Unsuitable for children under 13.

{ 5. PG-R }

Rating

Misc

Parental Guidance Recommended.

{ 6. R }

Press ꢂ/ ꢃto select { Misc }, then press ꢁ.

Press ꢂ/ ꢃto select an item, then press OK to

access.

Restricted; under 17 requires accompanying parent

or adult guardian.

{ 7. NC-17 }

Example: { Use Default Settings }

No one under 17 admitted.

ꢂThe options for the selected item appears.

{ 8. Adult }

ꢂIf the selection in the menu is greyed out, that

means the feature is not available or not possible to

change at the current state.

Useꢂ/ ꢃto select a setting and press OK to

conﬁrm.

Example: { No }

DVD softwares of any grades (adult/general/children)

can be played back. Should be viewed only by adults

due to graphic sexual material, violence or language.

Use ꢂ/ ꢃto select a rating level and press OK to

conﬁrm.

ꢂSelect { 8 Adult } to disable parental level and

allow all discs to play.

ꢂThe setting is selected and setup is completed.

To exit, press SETUP.

ꢀDVDs that are rated higher than the level you

selected will not play unless you enter your four-digit

password.

Restoring to original settings

Setting the { Use Default Settings } function will reset

all options and your personal settings to the factory

defaults, except your password and rating level.

Tips:

-This feature will not limit viewing if the disc

manufacturer did not code the disc.

-VCD, SVCD, CD have no level indication, so

parental control has no effect on these type of discs.

This also applies to most illegal DVDs.

-Some DVDs are not coded with a rating though the

movie rating may be printed on the disc cover. The

rating level feature does not prohibit play of such

discs.

Misc , press ꢂ/ ꢃto select

{ Use Default Settings }, then press OK.

ꢂThe menu will appear.

Helpful hint: Press ꢀto go back to previous menu item.

Press SETUP to exit the menu item.

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Menu Options

Use Default Settings

Yes

{ Yes }

Select this to reset to factory default settings.

{ No }

Select this to close the menu.

Use ꢀ/ ꢁto select a setting and press OK to

conﬁrm.

DivX^®Registration

DivX registration code allows you to rent and

purchase movies using the DivX VOD service from

the internet.

For more information, visit website:

www.divx.com/vod.

In ‘Misc’, press ꢂ/ꢃto select

{ DivX Registration }, then press OK.

ꢂThe registration code will appear.

B Use the registration code to rent or purchase the

movies from DivX VOD.

Registration service at www.divx.com/vod.

ꢂFollow the instructions and download the movie

from your computer onto a CD-R/RW for playback on

this DVD player.

Tips:

–

All the downloaded movies from DivX Registration

can only be played back on this DVD player.

Time search feature is not available during DivX

movie playback.

Tray Lock

Press SETUP button, then press the number button

"2006" in sequence to lock the tray.

All functionality of the player and playback remain

ꢀ

the same except for the OPEN/CLOSE button.

After the tray is locked, "Tray Lock Is On" will

ꢀ

appear on the screen when OPEN/CLOSE is

pressed.

To unlock the tray, just follow the same procedure

ꢀ

as above.

Download from Www.Somanuals.com. All Manuals Search And Download.

Speciﬁcations

DVD Player/Outputs/Supplied Accessories

DVD Player

Power supply

110 V - 240 V AC, 50/60 Hz

Power Consumption

12W (standby: <3W)

Net weight

1.35 kg

External dismensions

Signal System

Laser

360 X 43 X 209 mm (W/H/D)

PAL, NTSC

Semiconductor laser, wavelength 650/780 nm

Frequency range

DVD linear sound : 48 kHz sampling 4 Hz to 22 kHz

96 kHz sampling 4 Hz to 44 kHz

Signal-to-noise ratio

Audio dynamic range

Harmonic distortion

Wow and ﬂutter

More than 90 dB

More than 80 dB

Less than 65 dB

Below measurable level [(less than

0.001 % ( W.PEAK )]

Operating conditions

Temperature : 5 C to 35 C Operation status :Horizontal

Outputs

Video output

1.0 V ( p-p ) , 75 Ω negative sync., pin jack x 1

Component video output

(Y) 1.0 (p-p), 75 Ω negative sync., pin jack x 1

(P B)/(P R) 700 mV (p-p), 75 Ω, pin jack x 2

Audio output ( COAXIAL DIGITAL ) 0.5 V (p-p) 75 Ω pin jack x 1

Audio output (ANALOG)

2.0 V (rms), 680 Ω, pin jacks (L/R) x 1

Supplied Accessories

Audio/Video cable

Remote control(SE-R0301)

Batteries(AAA)

ꢀThe model complies with the above speciﬁcations.

ꢀDesigns and speciﬁcations are subject to change without notice.

ꢀThis model may not be compatible with features and /or speciﬁcations that may be added in the future.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

WARNING

Under no circumstances should you try to repair the DVD player yourself, as this will invalidate the

warranty. Do not open the DVD player as there is a risk of electric shock.

If a fault occurs, ﬁrst check the points listed below before taking the DVD player for repair. If you are unable

to remedy a problem by following these guides, consult your dealer or TOSHIBA for help.

Problem

No power

Solution

-Check if the AC power cord is properly connected.

-Press the I/2ON/STANDBY on the front of the DVD player

to turn on the power.

-Refer to your TV' s manual for correct Video In channel

selection. Change the TV channel until you see the DVD

screen.

No picture

-Check if the TV is switched on.

-If the progressive scan feature is activated but the connected

TV does not support progressive signals or the cables are

not connected accordingly. See pages 11-12 for proper

progressive scan set up or deactivate the progressive scan

feature as follow:

1) Press OPEN/CLOSE on the DVD Player.

2) When the disc tray is opened, press number button

the remote control for a few seconds.

Distorted picture

Picture clipped

-Sometimes a small amount of picture distortion may

appear depending on the disc being played back. This is not

malfunction.

-May be caused by View Mode Setting (see page 18). Set to

Original for normal viewing.

-Connect DVD Player directly to the TV.

Completely distorted picture or

black /white picture with DVD.

-Make sure the disc is compatible with the DVD player.

-Ensure that the DVD Player's setting is set to match that of

the disc and your TV.

-Adjust the volume.

No sound / distorted sound

No audio at digital output

-Check that the speakers are connected correctly.

-Check the digital connections.

-Check if your receiver can decode MPEG-2 or DTS and if not,

please make sure the digital output is set to PCM.

-Check if the audio format of the selected audio language

matches your receiver capabilities.

-Check that the cable is connected to the correct device (See

Connecting to television).

No sound and picture

Disc cannot be played

-The DVD⁺R/RW must be ﬁnalized.

-Ensure the disc label is facing up.

-Check if the disc is defective by trying another disc.

-Wrong region code.

-Check the disc for ﬁngerprint/scratches and clean with a soft

cloth wiping from centre to edge.

Picture freezes momentarily during playback

No return to start-up screen when disc is removed

-Reset the unit by switching the player off, then on again.

-Aim the Remote Control directly at the sensor on the front of

the player.

The player does not respond to the Remote Control

-Reduce the distance to the player.

-Replace the batteries in Remote Control.

-Re-insert the batteries with their polarities(+/- signs)as

indicated.

Buttons do not work

-To completely reset the player, unplug the AC cord from AC

outlet for 5-10 seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Problem

Solution

Player does not respond to some operating

commands during playback.

-Operations may not be permitted by the disc.

Refer to the instructions of the disc jacket.

DVD Player cannot read CDs /DVDs

Menu items cannot be selected

-Use a commonly available cleaning CD/DVD to clean

the lens before sending the DVD Player for repair.

-Press STOP twice before selecting system setup

menu.

-Depending on the disc availability,some menu items

cannot be selected.

Unable to select Progressive Scan on/off

-Ensure that the output of the Video Out signal is

switch to P-Scan/Component.

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary

Analogue audio:

Progressive scan:

DivX :

An electrical signal that directly

represents sound. In contrast,

digital audio can also be an electrical

signal, but is an indirect

representation of sound. See also

Digital audio.

It displays all the horizontal lines

of a picture at one time, as a signal

frame. This system can convert

the interlaced video from DVD into

progressive format for connection to

a progressive display. It dramatically

increases the vertical resolution.

DivX is a codec (compression/de-

compression) that can compress im-

ages to a very small amount of data.

Dolby Digital:

A system developed by Dolby

Laboratories that compresses

digital sound. It works with stereo

(2ch) or multi-channel audio.

Aspect ratio:

PCM:

The width of a TV screen relative to

it is height. Conventional TVs are 4:3

(i.e., the screen is almost square).

Widescreen models are 16:9 (the

screen is almost twice as wide as its

height)

(Pulse Code Modulation)

PCM is a format that converts audio

into digital data. It is mainly used for

Audio CDs and DAT. This unit can

play back sounds as realistic as

possible by converting even com-

pressed Dolby Digital and MPEG

audio to PCM.

DTS :

(Digital Theater System)

DTS is a Multi-channel surround

sound system, but it is different from

Dolby Digital. Both formats were

developed by Digital Theater

Systems, Inc.

Chapter:

Just as a book is split up into

several chapters, a title on a DVD

disc is usually divided into chapters.