Toshiba Copier DP 1810 User Manual

3. Operator’s Manual pocket (Back side)

Keep the Operator’s Manual in this.

4. Side cover

5. Bypass tray

Use this to make copies on special media types such as thick paper, overhead transparen-

cies or tracing paper.

P .85 “Replacing T o ner Cartridge”

6. Paper feed cover (of the Paper Feed Unit (optional))

7. Paper size indicator

8. Paper Feed Unit (optional, MY-1027)

Use this to add one more drawer to the equipment. A maximum of 250 sheets of plain paper

can be placed in one go.

20 Description of Each Component

Download from Www.Somanuals.com. All Manuals Search And Download.

9. Drawer

Maximum 250 sheets of plain paper can be placed in one go.

10. Front cover

Open this cover when you replace the toner cartridge.

Left side / Inner side

1. Original glass

Use this to copy three-dimensional originals, book-type originals and special paper such as

overhead transparencies or tracing paper, as well as plain paper.

P .40 “Placing Originals”

2. Control panel

Use this to perform copying, key in the copy quantity, or set other functions.

P .24 “Control panel”

3. Toner cartridge

P .9 “Recommended toner cartridges”

P .85 “Replacing T o ner Cartridge”

4. Power switch

Turn the power of the equipment ON or OFF with this.

P .27 “Preparation 1 - Turning Power ON”

5. Paper exit stopper

Use this to prevent the exiting paper from falling. Open this when you make a large amount

of copies on a larger size of paper (e.g. LD, LG).

6. AC-IN terminal

Use this to connect the co-packed power cable and the equipment.

Description of Each Component 21

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

7. USB terminal (4-pin)

With this terminal, the equipment can be connected to your PC using a commercially avail-

able USB cable.

y Use a USB2.0 Hi-Speed certified cable: USB cable supporting the USB2.0 Hi-Speed

mode (480 Mbps of transfer speed) certified by the USB Implementers Forum.

y Connect the equipment with a PC directly by the USB cable. When it is connected with a

PC via a USB hub, the equipment may not be recognized.

8. Receiving tray

9. Scanning area

The data of originals transported from the Automatic Document Feeder (optional, MR-2020)

are scanned here.

10. Original scale

Use this to check the size of an original placed on the original glass.

11. Platen sheet

P .61 “Copying in Same Page Order as Originals - Sort Copying -”

22 Description of Each Component

Download from Www.Somanuals.com. All Manuals Search And Download.

Configuration of options

The options listed below are available. Contact your service technician or service representative

for the details.

Automatic Document Feeder

(

)

MR-2020

Platen Cover

(

)

KA-1650PC

Expansion Memory

)

(

GC-1240

Main body

Paper Feed Unit

(

)

MY-1027

Desk

MH-1640

(

)

Description of Each Component 23

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

Control panel

20 19 18 17

1. [SORT] button/lamp

Use this to use the sorting function.

2. Media type setting button/lamps

Use this button to switch the media type of paper placed on the bypass tray.

P .72 “When Message Lamp is Lit/Blinking”

3. [DATA] lamp

The lamp blinks when print data are being received from a PC connected to the equipment.

4. Message lamps

Each of five lamps shows you the current status of the equipment.

For the meaning of each lamp and countermeasure of each status, see the following page:

5. Zoom buttons/lamp

Use them to set reproduction ratio. The lamp above the

duction ratio is 100%.

button is lit when the repro-

For how to zoom in or out copy image, see the following page:

P .56 “Zooming In/Out Copy Image”

6. LED display

Use this to display the number of copies set. The reproduction ratio appears here when the

copy qty. / zoom display selecting button (7) is pressed.

7. Copy qty. / zoom display selecting button/lamp

The display of (6) is switched between copy quantity and reproduction ratio each time you

press this button. The lamp beside the “%” mark is lit when the reproduction ratio appears.

24 Description of Each Component

Download from Www.Somanuals.com. All Manuals Search And Download.

8. [INTERRUPT] button/lamp

Use this to interrupt the copy job in process and perform another one (= interrupt copying).

For the details of interrupt copying, see the following page:

P .47 “Interrupting copying and making another copy - Interrupt copy -”

9. [ENERGY SAVER] button/lamp

Use this to let the equipment enter into the energy saving mode when the equipment is not

used. The lamp is lit when the equipment is in the energy saving mode.

For the details of the energy saving mode, see the following page:

P .28 “Saving energy when not in use - Energy saving mode -”

10. [FUNCTION CLEAR] button/lamp

This lamp blinks when copying is finished. Use this button to clear the set copy functions.

11. [CLEAR/STOP] button

Use this to stop the copy job in process or return the copy quantity keyed in to “1”.

12. [START] button/lamp

Use this to start copying. Copies can be made when the lamp is lit. It blinks when the equip-

ment is waiting for copying to be started.

For basic copy operations, see the following page:

P .45 “Making Copies”

13. Digital keys

Use them to key in any number such as copy quantity.

14. Original mode button/lamps

Use this button to set the image quality of copy according to that of an original.

For the details of image quality, see the following page:

P .65 “Selecting Image Mode”

15. Density adjustment buttons/lamps

Use this button to adjust the density of copy image. The [AUTO] lamp below the

(automatic copy density mode) button is lit when the density is being automatically adjusted.

For the details of density adjustment, see the following page:

P .66 “Adjusting Density Level”

16. Paper jam position lamps

The lamp blinks when an original or copy paper is jammed. The position where the lamp is

blinking shows where the paper jam has occurred.

P .30 “Preparation 2 - Placing Copy Paper”

17. [DRAWER] button/lamps

Use this button to select a drawer or the bypass tray to be used as a paper source. The lamp

of the paper source currently selected is lit. The lamp blinks when the selected drawer or tray

is running out of paper.

When paper in the drawer or on the bypass tray has run out, see the following page to add

paper:

18. Original setting lamp

The lamp is lit when originals are placed on the Automatic Document Feeder (optional).

This lamp blinks in the following situations:

When the original needs to be placed on the original glass (When the [START] button is

pressed without the original cover being opened after copies are made)

Description of Each Component 25

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

When the originals need to be placed on the Automatic Document Feeder (optional)

(When a paper jam in the Automatic Document Feeder is released)

When the Automatic Document Feeder (optional) on which the originals are placed is

raised.

19. [COPY] button/lamps

Use this button to select the size of paper to be used. The lamp of the paper size currently

selected blinks when this size of paper is not placed in the drawer or on the bypass tray.

See the following page for details:

P .54 “Manual paper selection”

20. [ORIGINAL] button/lamps

Use this button to specify the size of an original.

P .58 “Specifying both the sizes of the original and the copy paper”

21. APS/AMS selecting button/lamps

Automatic paper selection (APS): The equipment detects the size of original and automati-

cally selects the same size of copy paper.

P .53 “Paper Selection”

Automatic magnification selection (AMS): Set the size of copy paper to be used in advance.

The equipment then detects the size of original and automatically selects the most suitable

reproduction ratio to the copy paper.

P .56 “Automatic magnification selection (AMS)”

APS and AMS are available only when originals are placed on the Automatic Document

Feeder (optional, MR-2020).

26 Description of Each Component

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparation 1 - Turning Power ON

Turning power ON

Press the power switch to “ ” (ON) side.

The equipment starts warming itself up. The warm-up time takes approx. 25 seconds.

When the warm-up has finished, the [START] lamp is lit to show that the equipment is

ready for copying.

If you press the [START] button with an original placed while the warm-up is still continu-

ing, copying automatically starts after it has finished. This is called auto job start. When

the job is reserved, the [START] lamp blinks to show you the current status.

However, this function cannot be accessed while “0” is blinking on the LED display

(approx. 15 seconds).

Key in the access code if the equipment is managed under the

access code function.

Key in the 3-digit access code, and then press the [START] button. Then the equipment

is ready for copying.

y If the access code function is enabled, press the [FUNCTION CLEAR] button after

any operation has been finished to prevent unauthorized use of the equipment.

y For the details of the access code setting, ask your service technician.

Turning power OFF

Press the power switch to “

” (OFF) side.

Preparation 1 - Turning Power ON 27

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

Saving energy when not in use - Energy saving mode -

To reduce power consumption, the equipment automatically enters into the energy saving mode

when a specified period of time has passed since its last use. You can also turn the equipment

into this mode manually.

Types of energy saving mode

There are two types of the energy saving mode as follows.

Sleep mode: The power consumption is 18 W. “SLP” appears on the LED display, and only the

[ENERGY SAVER] lamp is lit.

Super sleep mode: The power consumption is 4 W. The LED display is blank, and only the

[ENERGY SAVER] lamp is lit.

y Either the sleep mode or the super sleep mode is enabled. The enabled mode and the time

until the mode is entered (Auto sleep time) can be changed.

P .70 “Changing of the Enabled Energy Saving Mode”

y There is another one called the low power mode. Since the time until the low power mode is

entered (Auto low power time) and the time until the energy saving mode is entered (Auto

sleep time) work simultaneously, if auto sleep time is set shorter than auto low power time,

the equipment enters into the energy saving mode, but not into the low power mode.

P .18 “Energy saving features”

To turn the equipment into the energy saving mode manually

Check that the equipment is in the ready status, and press the [ENERGY SAVER] button.

The equipment is now in the energy saving mode. The [ENERGY SAVER] lamp is lit.

Canceling conditions for energy saving mode

The energy saving mode is canceled under the following conditions. After the warm-up has been

completed, the equipment goes into the ready status.

Sleep mode

y When any of the buttons on the control panel is pressed

y When this equipment is connected to a PC with a USB cable

y When printing is performed from a PC connected with this equipment

y When the Platen Cover (optional) or the Automatic Document Feeder (optional) is raised

y When originals are placed on the Automatic Document Feeder (optional)

28 Preparation 1 - Turning Power ON

Download from Www.Somanuals.com. All Manuals Search And Download.

Super sleep mode

y When the [ENERGY SAVER] button on the control panel is pressed

y When the Platen Cover (optional) or the Automatic Document Feeder (optional) is raised

If this equipment is connected to your PC with a USB cable, change the setting so that it does

not enter the super sleep mode.

P .70 “Changing of the Enabled Energy Saving Mode”

Preparation 1 - Turning Power ON 29

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

Preparation 2 - Placing Copy Paper

Place copy paper in an appropriate paper source before you start copying.

Acceptable media types

Standard size plain paper (17 to 20 lb. Bond) can be used for the drawers in the equipment and

the Paper Feed Unit (optional). See the table below for the details.

Maximumsheet

Feeder

Media type

Paper size

capacity

Drawers of Plain paper

LT format:

LD, LG, LT, LT-R, COMP, 13"LG

A/B format:

250 sheets

(17 lb. Bond)

250 sheets

(20 lb. Bond)

the equip-

(17 - 20 lb. Bond)

ment and

PaperFeed

Unit

A3, A4, A4-R, B4, B5, B5-R, FOLIO

(optional)

Bypass tray Plain paper

LT format:

LD, LG, LT, LT-R, ST-R, COMP, 13"LG

A/B format:

100 sheets

(17 lb. Bond)

100 sheets

(20 lb. Bond)

1 sheet

(17 - 20 lb. Bond)^*2

A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO

THICK PAPER 1

(21 - 28 lb. Bond)

THICK PAPER 2

(29 lb. Bond - 90 lb.

Index)

(21 - 28 lb. Bond)

1 sheet

(29 lb. Bond - 90

lb. Index)

Tracing paper

(20 lb.)

1 sheet

Sticker labels

Transparencies^*3

1 sheet

LT only

*1 “Maximum sheet capacity” refers to the maximum number of sheets when TOSHIBA-recommended

paper is used. See the following page for the TOSHIBA-recommended paper:

P .31 “Recommended paper”

*2 13 to 16 lb. Bond paper can be used if it is set on the bypass tray sheet by sheet.

*3 Be sure to use the overhead transparencies that TOSHIBA recommends. When transparencies other

than the TOSHIBA-recommended ones are used, this could cause an equipment malfunction.

You cannot mix various paper sizes in one drawer.

Abbreviations for LT format sizes:

LT: Letter, LD: Ledger, LG: Legal, ST: Statement, COMP: Computer

30 Preparation 2 - Placing Copy Paper

Download from Www.Somanuals.com. All Manuals Search And Download.

Recommended paper

To ensure the best copy performance, TOSHIBA recommends the paper types listed below. If

you want to use paper other than that we recommend, contact your service technician.

Media type

Product name

Plain paper

TIDAL / Hammermill

Laser / Hammermill

20 lb. Bond

24 lb. Bond

32 lb. Bond

90 lb. Index

20 lb. Bond only

THICK PAPER 1

THICK PAPER 2

Exact Index / WAUSAU

Tracing paper / Ostrich International

5165 / Avery

Tracing paper

Sticker labels

Transparencies ^*1

X-10.0 / Folex

*1 Be sure to use the overhead transparencies that TOSHIBA recommends. When transparencies other

than the TOSHIBA-recommended ones are used, this could cause an equipment malfunction.

Paper types not acceptable

Do not use the types of paper listed below since they may cause paper jams.

y Damp paper

y Creased paper

y Wrinkled paper or paper prone to be curled

y Paper whose surface is extremely smooth or rough

Do not use the types of paper listed below since they may cause an equipment malfunction.

y Paper whose surface is specially treated

y Paper once printed with other copiers or printers

Storing paper

Observe the following cautions when storing copy paper:

y Wrap copy paper in its wrapping paper to prevent it from gathering dust.

y Do not expose copy paper to direct sunlight.

y Store copy paper in a damp-free place.

y Store copy paper on a flat surface to prevent it from being creased or bent.

Preparation 2 - Placing Copy Paper 31

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

Placing paper in drawers

Follow the procedure below to place copy paper in the drawer.

For the acceptable paper, see the following page:

P .30 “Acceptable media types”

Turn the power of the equipment ON.

Pull out the drawer carefully.

Pull out the drawer until it comes to a stop.

Press down the paper plate.

Press it down until you hear a click sound and it is no longer lifted up.

32 Preparation 2 - Placing Copy Paper

Download from Www.Somanuals.com. All Manuals Search And Download.

Pull out the trailing guide (A), and then reinstall the guide at the

position of the desired paper size.

The paper size is indicated on the bottom inner surface of the drawer.

While pushing the green knob of the side guides fully, widen the

gap between them.

Widen the gap with both hands.

Preparation 2 - Placing Copy Paper 33

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

Place paper in the drawer.

y The maximum number of sheets that can be placed at one time is 250 (17 to 20 lb.

Bond). Be sure that the stack height of paper is not higher than the line indicated at

the inner side of the side guide and trailing guide.

P .30 “Acceptable media types”

y Fan the paper well before placing it in the drawer, otherwise multiple feeding could

occur. Be careful that the paper does not cut your fingers.

y Place the paper face up. You may tell its “face” by the note on its wrapping paper.

Adjust the side guides to the desired paper size.

Be sure that a gap of approx. 0.02" (less than 0.04" in total) is left between the paper and

each side guide (shown as “A” in the picture). If the gap is inappropriate, this could cause

a paper misfeed.

34 Preparation 2 - Placing Copy Paper

Download from Www.Somanuals.com. All Manuals Search And Download.

Be sure that the stack of paper fits completely under the latches of

the side guides.

Change the paper size indicator to match the size of paper placed.

Push the drawer straight into the equipment slowly until it comes to

a stop.

Do not let your fingers be caught when closing the drawer.

This could cause injury.

When you place paper, register the size of the paper into the equipment. Be sure that the

size is registered correctly, or it could cause a paper jam.

For the registration of paper size, see the following page:

P .36 “Preparation 3 - Registering Size of Paper Placed”

Be sure to register the paper size when you have changed the paper size in the drawer,

as well as when you place paper in the corresponding drawer for the first time.

Preparation 2 - Placing Copy Paper 35

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

Preparation 3 - Registering Size of Paper Placed

When you place paper in a drawer for the first time or when you place paper whose size is differ-

ent from that of the paper which has been placed in the drawer, the new paper size needs to be

registered into the equipment.

Registration of standard sizes (LD, LT, LT-R, LG, ST-R) differs from that of standard sizes other

than these.

Registering standard size (LD, LT, LT-R, LG, ST-R)

In this section, LT size is registered in the drawer of the equipment as an example.

Press and hold the [COPY] and [DRAWER] buttons simultaneously

for more than two seconds.

“Fnc” appears on the LED display.

Press the [DRAWER] button several times until the lamp of the

drawer in which you placed paper is lit.

36 Preparation 3 - Registering Size of Paper Placed

Download from Www.Somanuals.com. All Manuals Search And Download.

Press the [COPY] button several times until the lamp of the paper

size you placed in the drawer is lit.

If the [FUNCTION CLEAR] button is pressed at this step, the size is not registered and

the equipment will return to its normal status.

Press the [START] button.

The paper size has been registered.

Registering other standard sizes

When standard size paper other than LD, LT, LT-R, LG or ST-R is placed, register this size as

“OTHER” size. Key in the code number of the paper size to register it as “OTHER” size.

See the table below for the code number of each size.

Paper size

Code No.

Paper size

Code No.

B5-R

A5-R ^*1

FOLIO

COMP

13"LG

A4-R

*1 A5-R and ST-R can be placed only on the bypass tray.

In this section, A4 size is registered in the drawer of the equipment as an example.

Press and hold the [COPY] and [DRAWER] buttons simultaneously

for more than two seconds.

“Fnc” appears on the LED display.

Preparation 3 - Registering Size of Paper Placed 37

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

Press the [DRAWER] button several times until the lamp of the

drawer in which you placed paper is lit.

Press the [COPY] button several times until the [OTHER] lamp is lit.

“Fxx” appears in the LED display. (Two digits come at “xx”.)

Key in the code number of the paper placed in the drawer.

e.g.) Placing A4 size (= code number “02”)

If the [FUNCTION CLEAR] button is pressed at this step, the size is not registered and

the equipment will return to its normal status.

Press the [START] button.

The paper size has been registered as “OTHER” size.

38 Preparation 3 - Registering Size of Paper Placed

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO MAKE COPIES

This chapter describes basic copy operations.

Placing Originals.....................................................................................................40

Acceptable original s ..........................................................................................................................40

Placing originals on the original glas s ...............................................................................................41

Placing booklet-type originals such as books or catalog s .................................................................42

Using Automatic Document Feeder (optional) ..................................................................................43

Placing originals on Automatic Document Feeder (optional) ............................................................44

Making Copies.........................................................................................................45

Stopping/Resuming copying..............................................................................................................46

Interrupting copying and making another copy - Interrupt copy -......................................................47

Using Bypass Tra y ..................................................................................................48

Bypass copyin g .................................................................................................................................49

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO MAKE COPIES

Placing Originals

Acceptable originals

Booklets, three-dimensional objects and some types of special media can be placed on the orig-

inal glass, as well as plain paper. When the Automatic Document Feeder (optional) is used, a

stack of plain paper originals can be automatically scanned one by one.

Acceptable sizes for auto-

Type of origi-

nals

Maximum

size

Setting position

Remarks

matic size detection

Original glass

Plain paper

Special media

11.69" x 17.01" Not acceptable for automatic

size detection

types^*2

Booklets

3-dimensional

objects

*4, *5, *6

Automatic

Document Feeder

(optional)

Plain paper

LD, LG, LT, LT-R, COMP, ST-R

of standard sizes

*1 The automatic size detection function is not enabled for A/B format.

*2 “Special media types” refers to special paper which is not acceptable for the Automatic Document

Feeder (optional), such as overhead transparencies or tracing paper.

*3 Do not place heavy objects (9 lb. or more) and do not press on it with force.

*4 Its paper weight should be between 13.3 lb. and 33.8 lb.

*5 Some media types may not be used.

*6 ST size originals must be placed in a landscape direction.

Maximum number of originals scanned in one go

Up to 250 original sheets can be scanned at one time. When the number of sheets to be

scanned exceeds 250 or the built-in memory in the equipment becomes full during the scanning

of the copy job, scanning stops, the [FUNCTION CLEAR] lamp blinks and the [START] lamp is

lit.

To copy the data scanned so far, press the [START] button. To delete them, press the [FUNC-

TION CLEAR] button.

When non-sort copying or sort copying for one set is performed, only the [FUNCTION CLEAR]

lamp blinks. Thus only data deletion is possible. After doing this, perform copying again with the

original divided.

40 Placing Originals

Download from Www.Somanuals.com. All Manuals Search And Download.

Placing originals on the original glass

Plain paper or some special media types which are not acceptable for the Automatic Document

Feeder (optional), such as overhead transparencies or tracing paper, should be placed on the

original glass.

Do not place heavy objects (9 lb. or more) and do not press on it with force.

Breaking the glass could injure you.

Raise the Platen Cover (optional) or the Automatic Document

Feeder (optional).

Place the original face down on the original glass and align it

against the left rear corner of the glass.

When copying highly transparent originals

When copying highly transparent originals such as overhead transparencies or tracing

paper, place a blank sheet of paper (A), the same size as the original or larger, over the

original (B).

Lower the Platen Cover (optional) or the Automatic Document

Feeder (optional) carefully.

Placing Originals 41

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO MAKE COPIES

Placing booklet-type originals such as books or catalogs

Place a book-type original on the original glass.

Do not place heavy objects (9 lb. or more) and do not press on it with force.

Breaking the glass could injure you.

Raise the Platen Cover (optional) or the Automatic Document

Feeder (optional).

Open the desired page of the original and place it face down.

Align it against the left rear corner of the glass.

Lower the Platen Cover (optional) or the Automatic Document

Feeder (optional) carefully.

y Do not try to lower the Platen Cover (optional) or the Automatic Document Feeder

(optional) forcibly when the original is very thick. There will be no problem in copying

even if they are not fully lowered.

y Do not look fully at the original glass since intensive light may leak out during copy-

ing.

42 Placing Originals

Download from Www.Somanuals.com. All Manuals Search And Download.

Using Automatic Document Feeder (optional)

When a stack of originals are placed on the Automatic Document Feeder (optional), the originals

are automatically scanned one by one. The following types of originals are available:

Maximum number of

sheets acceptable

Media types

Maximum size

Paper weight

Plain paper

11.69" x 17.01"

100 sheets

(or stack height 0.62")

13.3 - 33.8 lb.

y Some media types may not be used.

y The maximum number of sheets acceptable varies depending on the media types of the

originals.

y ST size originals must be placed in a landscape direction.

y Sizes which the Automatic Document Feeder (optional) can detect automatically are LD, LG,

LT, LT-R, COMP and ST-R.

Precautions for Automatic Document Feeder (optional)

Do not use the following types of original since such types may cause a paper jam or damage to

the equipment:

y Extremely wrinkled, folded or curled ones

y Ones with carbon paper

y Taped, pasted or cut-out ones

y Clipped or stapled ones

y Ones with holes or tears

y Damp ones

y Overhead transparencies or tracing paper

y Coating paper (e.g. coated with wax)

y Ones with many holes punched (e.g. loose leaf paper)

The following types of originals are usable but need extra care:

y Ones which cannot be made to slide with the fingers or whose surface is specially treated

(they may not be able to be separated from each other at feeding)

y Folded or curled ones (should be smoothed out before being used)

When black streaks appear on the copied image

If the scanning area or the guide area is dirty, image problems such as black streaks on the cop-

ied image may occur. Weekly cleaning of these areas is recommended.

P .51 “COPYING FUNCTIONS”

Placing Originals 43

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO MAKE COPIES

Placing originals on Automatic Document Feeder (optional)

Align all the originals.

Place them face up and align the side guides to the original length.

y The top sheet of the originals will be scanned first.

y The total sheets of originals placed must not exceed 100 (13.3 to 20 lb.) or the stack

height of the originals must not exceed 0.62" regardless of their sizes.

When placing a large amount of originals with a long width

Pull out the original stopper so that the exiting originals will not fall. When replacing this

stopper, lift it slightly and push it in.

44 Placing Originals

Download from Www.Somanuals.com. All Manuals Search And Download.

Making Copies

Follow the procedure below to make copies.

The reproduction ratio or density of the copied image can be set. See the following page for the

details:

Check if paper is placed in the drawer.

For the acceptable types and sizes of paper, see the following pages:

P .30 “Acceptable media types”

P .40 “Acceptable originals”

Place the original.

For acceptable originals or how to place originals, see the following pages:

P .44 “Placing originals on Automatic Document Feeder (optional)”

P .41 “Placing originals on the original glass”

P .42 “Placing booklet-type originals such as books or catalogs”

Key in the desired number of copies (= copy quantity) when you

copy more than one set.

e.g.) 5 sets

If you want to correct the copy quantity keyed in, press the [CLEAR/STOP] button, and

then key in the correct number.

Select the copy modes as required.

P .51 “COPYING FUNCTIONS”

Press the [START] button.

Copying starts. The paper will exit with its copied side down.

The paper exit area and exiting paper are hot immediately after the exit. Handle them

with care.

Making Copies 45

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO MAKE COPIES

When the number of sheets exiting has exceeded 250

To prevent exiting paper from falling off the receiving tray, the equipment causes copying to

pause when approx. 250 sheets of paper have continuously exited. At this time the [START]

lamp is lit and the [FUNCTION CLEAR] lamp blinks on the control panel. Also the paper jam

position lamp ( ) at the middle is lit.

Remove the paper from the receiving tray, and then press the [START] button. Copying

resumes.

Press the [FUNCTION CLEAR] button to end the copy job.

When the paper has run out

When the paper in the drawer has run out during copying, the copying stops and the paper

empty lamp blinks.

The [DRAWER] lamp corresponding to the one whose paper has run out blinks.

Add paper to the drawer and press the [START] button. Copying then resumes.

Stopping/Resuming copying

Press the [CLEAR/STOP] button to stop scanning or copying.

Press the [CLEAR/STOP] button during scanning or copying.

Scanning or copying stops. Press the [CLEAR/STOP] button again to end the copy job.

Press the [START] button to resume the copy job.

46 Making Copies

Download from Www.Somanuals.com. All Manuals Search And Download.

Interrupting copying and making another copy - Interrupt copy -

You can interrupt copying of one job and make another copy job (= interrupt copying). The copy

quantity or functions applied to the interrupted job are stored in the memory of this equipment,

so that you will not need to set them again when the interrupted job resumes.

Interrupt copying is available only when the originals are placed on the Automatic Document

Feeder (optional) and the sort functions are used.

Press the [INTERRUPT] button.

The [INTERRUPT] lamp blinks, and the lamp will be fully lit after a while.

When the [INTERRUPT] button is pressed during scanning, the [INTERRUPT] lamp

blinks, and then the lamp will be fully lit after the scanning has finished.

Replace the original with a new one.

Select the copy modes as required, and then press the [START]

button.

Interrupt copying starts.

After you have finished interrupt copying, press the [INTERRUPT]

button.

The copying status returns to the one before the interruption.

Even if you do not press the [INTERRUPT] button, a certain time after the interrupt copy-

ing has finished, the auto clear function will work and the interrupt mode will automati-

cally be cleared.

Press the [START] button.

The job interrupted will resume.

Making Copies 47

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO MAKE COPIES

Using Bypass Tray

Place paper on the bypass tray when you use the following media types as copy paper:

y Thick paper (21 lb. Bond to 90 lb. Index)

y Special media types such as tracing paper, sticker labels or overhead transparencies

y Standard size paper which cannot be placed in a drawer (e.g. ST-R)

Using the bypass tray is recommended also for copying on standard-size paper other than those

placed in the drawers. The following sizes are available for bypass copying:

Maximum sheet

Media type

Paper size

capacity

Plain paper

LT format:

LD, LG, LT, LT-R, ST-R, COMP, 13"LG

A/B format:

100 sheets (17 lb. Bond)

100 sheets (20 lb. Bond)

(17 - 20 lb. Bond)^*2

THICK PAPER 1

(21 - 28 lb. Bond)

THICK PAPER 2

(29 lb. Bond - 90 lb. Index)

Tracing paper

1 sheet

(21 - 28 lb. Bond)

A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO

1 sheet

(29 lb. Bond - 90 lb. Index)

1 sheet

(20 lb.)

Sticker labels

Transparencies^*3

1 sheet

LT only

*1 “Maximum sheet capacity” refers to the maximum number of sheets when TOSHIBA-recommended

paper is used. See the following page for the TOSHIBA-recommended paper:

P .31 “Recommended paper”

*2 13 to 16 lb. Bond paper can be used if it is set on the bypass tray sheet by sheet.

*3 Be sure to use the overhead transparencies that TOSHIBA recommends. When transparencies other

than the TOSHIBA-recommended ones are used, this could cause an equipment malfunction.

When you place paper of a larger size, pull out the paper holder before you start bypass copy-

ing.

48 Using Bypass Tray

Download from Www.Somanuals.com. All Manuals Search And Download.

Bypass copying

This section describes the bypass copying procedure.

Place paper straight on the bypass tray face down. Then align the

side guides to the paper length while holding (A).

y Be sure that the stack height of paper does not exceed the indicators of the side

guides.

y Fan the stack of paper well before placing it on the bypass tray.

y Do not push the paper forcibly into the entrance of the bypass feeder. This could

cause a paper misfeed.

Press the [COPY] button several times until the lamp of the paper

size you placed on the bypass tray is lit.

If you copy on standard size paper other than LD, LT, LT-R, LG or ST-R, select [OTHER]

and key in the code number of the paper placed on the bypass tray.

e.g.) Placing A4 size (= code number “02”)

For the paper sizes to be registered as OTHER size, see the following page:

P .37 “Registering other standard sizes”

Using Bypass Tray 49

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO MAKE COPIES

Press the [START] button.

The paper size has been registered.

Press the media type setting button until the lamp of the media type

placed on the bypass tray is lit.

You can select the media type from the following three:

THICK PAPER 1: Thick paper (21 to 28 lb. Bond)

THICK PAPER 2: Thick paper (29 lb. Bond to 90 lb. Index), sticker labels

TRANSPARENCY: Overhead transparencies

y You do not need to select the media type when you use plain paper (17 to 20 lb.

Bond) or tracing paper.

y If you select a different media type from the one you placed on the bypass tray, this

could cause a paper jam or the quality of the copied image could be lowered.

Place the original.

Select the other copy modes as required, and then press the

[START] button.

Copying starts.

When you make copies on overhead transparencies using the bypass tray, pick up the

transparencies which have exited onto the receiving tray one by one. If the transparen-

cies pile up, they may become curled and not be good for projection.

y When the paper on the bypass tray has run out during copying, copying continues

with the paper of the same size in the drawer as the one on the bypass tray. (If the

size of the paper on the bypass tray has not been registered in advance, however,

copying stops. In this case, add paper to the bypass tray and press the [START] but-

ton to resume copying.)

y When bypass copying has finished, the [FUNCTION CLEAR] lamp blinks. Press the

[FUNCTION CLEAR] button so that the paper size setting for the bypass tray will be

cleared. Press the [FUNCTION CLEAR] button again so that bypass copying will be

switched to copying with drawer feeding.

50 Using Bypass Tray

Download from Www.Somanuals.com. All Manuals Search And Download.

COPYING FUNCTIONS

This chapter describes various functions related to copy operations, such as how to make enlargement or

reduction copies, or how to adjust the quality of copy images.

Default Settings.......................................................................................................52

Paper Selectio n .......................................................................................................53

Automatic paper selection (APS) ......................................................................................................53

Manual paper selectio n .....................................................................................................................54

Zooming In/Out Copy Imag e ..................................................................................56

Automatic magnification selection (AMS)..........................................................................................56

Specifying both the sizes of the original and the copy paper ............................................................58

Specifying reproduction ratio manually .............................................................................................59

Copying in Same Page Order as Originals - Sort Copying -...............................61

Copying Both Sides of Card into 1 Page - ID CARD -..........................................63

Selecting Image Mode ............................................................................................65

Adjusting Density Level .........................................................................................66

Download from Www.Somanuals.com. All Manuals Search And Download.

COPYING FUNCTIONS

Default Settings

Initial settings established when the equipment is powered on before any of the user functions

are changed are called default settings. Each setting returns to its default when the power is

turned ON, when the energy saving mode is canceled, and when the [FUNCTION CLEAR] but-

ton is pressed.

Each default setting of this equipment at the time of the installation is shown below.

Item

Contents

Default setting at installation

Reproduction ratio

Copy quantity

25 - 200%

1 - 999

100%

Automatic paper selection (APS) ^*1

Manual paper selection

Paper selection

Automatic paper selection (APS)

Density adjustment

Automatic copy density mode, Manual Automatic copy density mode

copy density mode

Image mode

Sorting

TEXT/PHOTO, PHOTO, TEXT

Non-sort copying, sort copying

TEXT/PHOTO

Non-sort copying

*1 The automatic paper selection (APS) can be set only when the Automatic Document Feeder (optional) is

used.

If you need to change the default settings listed above, contact your service representative.

52 Default Settings

Download from Www.Somanuals.com. All Manuals Search And Download.

Paper Selection

You can select the size of copy paper in two ways; one is automatic paper selection in which the

equipment automatically selects copy paper of the same size as the original, and the other is

manual paper selection in which you can select the desired paper size manually.

Automatic paper selection (APS):

The equipment detects the size of the original placed and automatically selects copy paper of

the same size as the original. This function is enabled only when standard size originals (LD, LG,

LT, LT-R, COMP, ST-R) are used and also the Automatic Document Feeder (optional) is used.

Manual paper selection:

You can select the desired size of copy paper manually. This function can be used in a case the

APS cannot be used, such as when originals are non-standard sizes or overhead transparen-

cies, or when an original is placed on the original glass.

Automatic paper selection (APS) can be used only when you place originals on the Automatic

Document Feeder (optional).

Automatic paper selection (APS)

When you place a standard size original on the Automatic Document Feeder (optional), the

equipment detects its size and automatically selects copy paper of the same size as the original.

The standard sizes the equipment can detect are as follows: LD, LG, LT, LT-R, COMP, ST-R

The equipment may not be able to correctly detect the size of the originals listed below. Use

manual paper selection for the following originals:

y Highly transparent ones (e.g. overhead transparencies, tracing paper)

y Wholly dark ones or ones with dark borders

y Non-standard size ones (e.g. newspapers, magazines)

P .54 “Manual paper selection”

Place paper in the drawer.

P .36 “Preparation 3 - Registering Size of Paper Placed”

Place the original on the Automatic Document Feeder.

Paper Selection 53

Download from Www.Somanuals.com. All Manuals Search And Download.

COPYING FUNCTIONS

Press the APS/AMS selecting button and select APS. (The APS

lamp is lit.)

When the Automatic Document Feeder (optional) is not installed, the APS/AMS selecting

button is not enabled.

Select the other copy modes as required, and then press the

[START] button.

Manual paper selection

Select the paper size with this method when an original is placed on the original glass, and also

when you use the following originals whose sizes may not be detected correctly with automatic

paper selection:

y Highly transparent ones (e.g. overhead transparencies, tracing paper)

y Wholly dark ones or ones with dark borders

y Non-standard size (e.g. newspapers, magazines)

In this method, if the desired size of copy paper is not placed in the drawer, replace the paper

already placed in the drawer with the desired one, or place the desired size of paper on the

bypass tray.

P .37 “Registering other standard sizes”

Place paper in the drawer.

Place the original.

54 Paper Selection

Download from Www.Somanuals.com. All Manuals Search And Download.

Press the [DRAWER] button several times until the lamp of the

desired drawer is lit.

e.g.) Selecting the drawer of the equipment

Select the other copy modes as required, and then press the

[START] button.

Paper Selection 55

Download from Www.Somanuals.com. All Manuals Search And Download.

COPYING FUNCTIONS

Zooming In/Out Copy Image

You can set the reproduction ratio of the copy image in the following three ways:

Automatic magnification selection (AMS):

Specify the size of the copy paper in advance. As the original is placed, the equipment then

detects the size of the original and sets the reproduction ratio most suited to the size of copy

paper automatically. This function is enabled only when standard size originals (LD, LG, LT,

LT-R, COMP, ST-R) are used and also the Automatic Document Feeder (optional) is used.

Specifying both the sizes of the original and the copy paper:

When you specify the sizes of both the original and the copy paper, the equipment automatically

sets the reproduction ratio most suited to both of these sizes. This function can be used in case

AMS cannot be, such as when the originals are overhead transparencies, or when an original is

placed on the original glass.

Specifying reproduction ratio manually:

Specify the reproduction ratio manually with the Zoom buttons (zooming out:

in: ) from 25% to 200%.

, zooming

Automatic magnification selection (AMS)

Specify the copy paper size to be used in advance. The equipment then detects the size of the

original and automatically sets the most suitable reproduction ratio for the size of copy paper, as

the original is placed.

y Automatic magnification selection (AMS) can be used only when you place originals on the

Automatic Document Feeder (optional).

y The standard sizes the equipment can detect are as follows: LD, LG, LT, LT-R, COMP, ST-R

Automatic magnification selection (AMS) may not work correctly for the size of originals listed

below. Use other methods to set the reproduction ratio for the following originals:

y Highly transparent ones (e.g. overhead transparencies, tracing paper)

y Wholly dark ones or ones with dark borders

y Non-standard size (e.g. newspapers, magazines)

56 Zooming In/Out Copy Image

Download from Www.Somanuals.com. All Manuals Search And Download.

Place paper in the drawer.

Press the [COPY] button several times until the lamp of the desired

paper size is lit.

e.g.) Selecting LT size

You can select the desired paper size with the [DRAWER] button in the same procedure.

Press the APS/AMS selecting button until the AMS lamp is lit.

Place the original on the Automatic Document Feeder (optional).

Select the other copy modes as required, and then press the

[START] button.

Copying is performed with the most suitable reproduction ratio for the specified paper

size.

If the [FUNCTION CLEAR] lamp is blinking and copying stops

The direction of the original placed is not correct. Press the [FUNCTION CLEAR] button to exit

the original. Then rotate the original by 90 degrees to place it in the correct direction.

Zooming In/Out Copy Image 57

Download from Www.Somanuals.com. All Manuals Search And Download.

COPYING FUNCTIONS

Specifying both the sizes of the original and the copy paper

Place paper in the drawer.

Place the original.

Press the [ORIGINAL] button several times until the lamp of the

desired original size is lit.

e.g.) Selecting LG for the original

Press the [COPY] button several times until the lamp of the desired

paper size is lit.

e.g.) Selecting LT for copy paper

y You can select the desired paper size with the [DRAWER] button in the same proce-

dure.

y When standard size paper other than LD, LT, LT-R, LG or ST-R is placed, register this

size as “OTHER” size in advance.

The most appropriate reproduction ratio for both the sizes of the original and the copy

paper is set.

Select the other copy modes as required, and then press the

[START] button.

58 Zooming In/Out Copy Image

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifying reproduction ratio manually

Place paper in the drawer.

Place the original.

Press the Copy qty. / zoom display selecting button.

The reproduction ratio appears on the LED display.

Press the

desired reproduction ratio appears.

One press of each button increases or decreases the reproduction ratio by 1%. When

you keep pressing either of them, the reproduction ratio also keeps changing. The

reproduction ratio can be set from 25% to 200%.

(zooming out) or

(zooming in) button until the

y Press the

button to return it to 100%.

and buttons simultaneously to set it 25% (the minimum

y Press the

reproduction ratio).

y Press the

and

buttons simultaneously to set it 200% (the maximum

reproduction ratio).

Zooming In/Out Copy Image 59

Download from Www.Somanuals.com. All Manuals Search And Download.

COPYING FUNCTIONS

Press the [COPY] button several times until the lamp of the desired

paper size is lit.

e.g.) Selecting LT for copy paper

y You can select the desired paper size with the [DRAWER] button in the same proce-

dure.

y When standard size paper other than LD, LT, LT-R, LG or ST-R is placed, register this

size as “OTHER” size in advance.

P .37 “Registering other standard sizes”

Select the other copy modes as required, and then press the

[START] button.

60 Zooming In/Out Copy Image

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying in Same Page Order as Originals - Sort Copying -

When you make several sets of copies, the copies can be made to exit in the same order as the

originals in each set. This is called sort copying.

Copied and sorted in 2 sets

Copied in 2 sets without being sorted

Place paper in the drawer.

Place the original.

When originals are placed on the Automatic Document Feeder (optional), this function is

automatically set. In this case, proceed to step 4.

Press the [SORT] button.

The [SORT] lamp is lit and sort copying is enabled.

Copying in Same Page Order as Originals - Sort Copying - 61

Download from Www.Somanuals.com. All Manuals Search And Download.

COPYING FUNCTIONS

Set the copy quantity, select other copy modes as required, and

then press the [START] button.

When the original is placed on the Automatic Document Feeder (optional), copying

starts.

When the original is placed on the original glass, it is scanned, the [SORT] lamp and the

[FUNCTION CLEAR] lamp blink, the [START] lamp is lit and “set” appears on the LED

display. Then proceed as follows.

Place the next original on the original glass, and then press the

[SORT] button.

The original is scanned.

Repeat this until all originals have been scanned.

After the scanning of the last original is finished, press the [START]

button.

Copying starts.

62 Copying in Same Page Order as Originals - Sort Copying -

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying Both Sides of Card into 1 Page - ID CARD -

The both sides of a card-sized original can be copied into one side of LT paper. This function is

useful when you need to copy massive amounts of 2-sided cards.

Front side

Back side

Place paper in the drawer.

Place LT or LT-R size paper in the drawer or on the bypass tray.

Press and hold the media type setting button and [SORT] button

simultaneously for more than two seconds.

The AMS selection lamp, the [SORT] lamp and the [FUNCTION CLEAR] lamp blink, and

the ID card function is set.

To clear the ID card function, press the [FUNCTION CLEAR] button.

Raise the Platen Cover (optional) or the Automatic Document

Feeder (optional).

Copying Both Sides of Card into 1 Page - ID CARD - 63

Download from Www.Somanuals.com. All Manuals Search And Download.

COPYING FUNCTIONS

Place a card original on the original glass.

Place the card face down, aligning and pushing it to the left rear corner of the original

glass.

The portion of an original which is on the upper and left edges (width of approx. 0.08") of

the original glass may not be copied. Place an original away from both edges, if you want

to copy the whole of the original.

Lower the Platen Cover (optional) or the Automatic Document

Feeder (optional) carefully.

Select the other copy modes (copy quantity, density, image mode

and media type) as required, and then press the [START] button.

The scanning of its top side starts and “set” appears on the LED display.

Raise the Platen Cover (optional) or the Automatic Document

Feeder (optional).

Turn over the card and place it on the original glass again.

Align and push it to the left rear corner of the original glass.

The portion of an original which is on the upper and left edges (width of approx. 0.08") of

the original glass may not be copied. Place an original away from both edges, if you want

to copy the whole of the original.

Lower the Platen Cover (optional) or the Automatic Document

Feeder (optional) carefully.

Press the [START] button.

The back side of the original is scanned and copying starts.

64 Copying Both Sides of Card into 1 Page - ID CARD -

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting Image Mode

You can select the most suitable quality of the copied image in the following three modes

depending on the originals:

TEXT/PHOTO: Originals with text and photographs mixed

PHOTO: Originals with photographs

TEXT: Originals with text only or with text and fine illustrations only

“TEXT/PHOTO” is set by default at the installation of the equipment.

Place paper in the drawer.

Place the original.

Press the original mode button until the lamp of the desired mode

is lit.

e.g.) Original with photographs

Select the other copy modes as required, and then press the

[START] button.

Selecting Image Mode 65

Download from Www.Somanuals.com. All Manuals Search And Download.

COPYING FUNCTIONS

Adjusting Density Level

The automatic copy density mode, which automatically selects the most suitable density level for

the copied image by detecting that of the original, is set by default at the installation of the equip-

ment. You can also adjust the density level as desired manually (=manual copy density mode) in

the following procedure:

Place paper in the drawer.

Place the original.

Press the density adjustment buttons (

to adjust the density to the desired level.

The density level can be set within 7 stages. One press of each button increases or

decreases the density level by one stage. When you keep pressing either of them, the

density level also keeps changing.

(light) or

(dark))

Select the other copy modes as required, and then press the

[START] button.

To return it to the automatic copy density mode

Press the

(AUTO) button.

66 Adjusting Density Level

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTINGS AND MANAGEMENT OF

EQUIPMENT

This chapter describes how to switch the operation sound ON or OFF, how to check the total number of

sheets you have copied and how to switch the energy saving mode.

Switching Operation Sound On/Off.......................................................................68

Checking Total Number Copied.............................................................................69

Changing of the Enabled Energy Saving Mode ...................................................70

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTINGS AND MANAGEMENT OF EQUIPMENT

Switching Operation Sound On/Off

You can switch the operation sound of the equipment on or off.

Press and hold the

neously for more than two seconds.

(light) and

(dark) buttons simulta-

“Fnc” appears on the LED display.

The density adjustment lamps show the sound status as follows:

All lamps on: Sound on

All lamps off: Sound off

Press the

(AUTO) button to switch the sound on or off.

Press the [START] button.

The equipment returns to its normal status.

68 Switching Operation Sound On/Off

Download from Www.Somanuals.com. All Manuals Search And Download.

Checking Total Number Copied

You can check the total number of sheets ever copied or printed. The total number of sheets

appears on the LED display.

Press and hold the

The upper digits of the total number appear on the LED display. The total number is

shown blinking.

button for more than two seconds.

e.g.) The total number is 12,527

Switch the display to check the rest of the total number.

Press the

(zooming out) or

(zooming in) button to switch the display.

Press any button other than the

have finished checking.

button when you

The equipment returns to its normal status.

The total number of sheets cannot be reset.

Checking Total Number Copied 69

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTINGS AND MANAGEMENT OF EQUIPMENT

Changing of the Enabled Energy Saving Mode

The settings of the enabled energy saving mode and auto sleep time (time until entering the

mode) can be changed.

Press and hold the

The present mode name (Sleep mode: SLP or Super sleep mode: SPS) is displayed in

the LED display for approx. 2 seconds, and then the current auto sleep time is displayed.

button for more than two seconds.

e.g.) Auto sleep time: 15 minutes in the super sleep mode

Press the

button to switch the enabled mode.

The mode is switched each time you press the button, and the selected mode name is

displayed in the LED display for approx. 2 seconds.

Press the

the auto sleep time.

The auto sleep time (1 to 240 minutes / 24 steps) is switched each time you press the

button, and the specified time is displayed in the LED display.

(zooming out) or

(zooming in) button to change

Press the [START] button.

The LED display returns to the normal one.

70 Changing of the Enabled Energy Saving Mode

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

This chapter describes how to release a paper jam, how to replace a toner cartridge and how to settle other

trouble.

When Message Lamp is Lit/Blinking.....................................................................72

Paper Jams..............................................................................................................75

Checking position of paper jam s .......................................................................................................75

Paper jams within Automatic Document Feeder (optional) (Lower)..................................................76

Paper jams within Automatic Document Feeder (optional) (Upper)..................................................78

Paper jams on bypass tray................................................................................................................80

Paper jam behind transfer uni t ..........................................................................................................81

Paper jams within fuser uni t ..............................................................................................................82

Paper jams within Paper Feed Unit (optional)...................................................................................84

Replacing Toner Cartridg e .....................................................................................85

Before Calling Service Technician ........................................................................90

General operation .............................................................................................................................90

Original/Copy paper-related items ....................................................................................................91

Image trouble ....................................................................................................................................92

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

When Message Lamp is Lit/Blinking

Message lamps on the control panel are lit or blink depending on the status of the equipment.

Each lamp shows the following status:

1. Cover open lamp

This blinks when any cover of the equipment, such as the front cover, the side cover or the

upper cover of the Automatic Document Feeder (optional), is not securely closed. Close it

securely.

2. Paper empty lamp

This blinks when the paper in a drawer or on the bypass tray has run out. Add paper. For

how to place paper, see the following pages for the details:

3. Toner lamp

This shows you the current status of the remaining toner (only when a TOSHIBA-recom-

mended toner cartridge is used).

Lit: There is only a little toner left in the toner cartridge. (You do not have to replace the

cartridge.)

Blinking: The toner in the toner cartridge has run out. (Replace the cartridge.)

y It occasionally happens that the toner lamp may not light because the toner remaining in

the cartridge does not lie evenly.

y When the toner lamp starts being lit, it is advisable to purchase a new TOSHIBA-recom-

mended cartridge to prepare for its replacement.

y When a toner cartridge other than the one we recommend is used, remaining toner can-

not be checked. The toner lamp is lit or it blinks.

72 When Message Lamp is Lit/Blinking

Download from Www.Somanuals.com. All Manuals Search And Download.

To assure an optimal printing performance, we recommend that you use only TOSHIBA

toner cartridges.

Recommended toner cartridges

To assure optimal printing performance, we recommend that you use only genuine TOSHIBA toner car-

tridges. If you use a TOSHIBA-recommended toner cartridge, you can utilize the following three functions

of this equipment:

Cartridge detecting function: This function checks if the toner cartridge is correctly installed and notifies

you if it is not.

Toner-remaining check function: This function notifies you when there is little toner remaining in the

cartridge.

Image quality optimization function: This function controls image quality according to the characteris-

tics of the toner to be used and enables you to print images of an optimal quality.

If you are using a toner cartridge other than the one we recommend, the equipment may not be able to

detect whether it is installed or not. Therefore, even if the toner cartridge is correctly installed, the toner

lamp lights or blinks and printing may not be performed. You may also not be able to utilize the image

quality optimization function and the toner remaining check function.

If you are using a toner cartridge other than the one we recommend, toner is not recognized. If this is a

problem for you, please contact your service representative. Remember you will not be able to utilize the

Toner remaining check function and Image quality optimization function as we mentioned.

4. Paper jam lamp

This blinks when an original or a sheet of copy paper is jammed.

For how to release paper jams, see the following page:

P .43 “Precautions for Automatic Document Feeder (optional)”

When Message Lamp is Lit/Blinking 73

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

5. Service call lamp

This is lit or blinks when the support of your service technician is needed. Contact your ser-

vice representative.

When the

key of the digital keys and the [CLEAR/STOP] button are pressed simulta-

neously, an error code (consisting of a letter of the alphabet and numbers) appears on the LED

display. Contact your service representative with this code.

Never attempt to repair, disassemble or modify the equipment by yourself.

This could cause an electric shock, a fire or serious injury.

Contact your service representative when the equipment is in an abnormal condition or any mal-

function is found.

74 When Message Lamp is Lit/Blinking

Download from Www.Somanuals.com. All Manuals Search And Download.

Paper Jams

Checking position of paper jams

When an original or a sheet of copy paper has jammed within the equipment, copying stops and

the paper jam lamp blinks.

Additionally, the paper jam position lamp blinks to show you where the paper jam has occurred.

Check the position and release the jammed paper.

1. Automatic Document Feeder (optional) ( P .76,

P .78)

2. Bypass tray ( P .80) / Transfer unit ( P .81) / Fuser unit ( P .82)

3. Paper Feed Unit (optional) ( P .84)

Release the jammed paper, and then press the [START] button. Copying resumes.

When paper jams occur frequently

When paper jams occur frequently, they may be due to one of the causes listed below. Check

the following items when they occur frequently:

y Originals which are not acceptable for the Automatic Document Feeder (optional) are

placed.

y Paper which is not acceptable for the equipment is used.

P .31 “Paper types not acceptable”

y The sizes of paper placed in the drawer or on the bypass tray are not registered into the

equipment properly.

P .36 “Preparation 3 - Registering Size of Paper Placed”

P .49 “Bypass copying”

y More jammed paper is still remaining after the release of a paper jam.

y There is no gap between the side guides and the paper in the drawer, or the gap is too wide.

y The stack height of the paper is exceeding the indicators in the drawer.

Paper Jams 75

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

When releasing jammed paper

Observe the following precautions when you release jammed paper:

Do not tear jammed paper.

Pull out jammed paper carefully with both hands, trying not to tear it. If you release it forcibly, the

jammed paper will be torn and it will make the release difficult. If it is torn, be sure that the torn

part is not left inside the equipment.

Do not touch the fuser unit or the metal part around the unit.

When you release paper jammed within the fuser unit, do not touch the fuser unit or the metal

part around the unit. This could cause burns, or injury to your hands if you touch the inside of the

equipment.

Do not touch the photoconductive drum.

When you release the paper jammed within the transfer unit or the fuser unit, be careful not to

touch the photoconductive drum. This could stain the copy images.

Paper jams within Automatic Document Feeder (optional) (Lower)

Open the Automatic Document Feeder.

76 Paper Jams

Download from Www.Somanuals.com. All Manuals Search And Download.

Open the reverse cover, and remove the original.

Close the Automatic Document Feeder.

Raise the lever, and open the upper cover.

Paper Jams 77

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Raise the original feeder tray, and remove the original under the

tray.

Lower the original feeder tray.

Close the upper cover.

Paper jams within Automatic Document Feeder (optional) (Upper)

Raise the lever and open the upper cover.

78 Paper Jams

Download from Www.Somanuals.com. All Manuals Search And Download.

Remove the original.

Turn the dial to remove the original.

Open the transport guide.

Paper Jams 79

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Raise the guide plate under the transport guide, and remove the

original under the guide plate.

Close the transport guide.

Close the upper cover.

Paper jams on bypass tray

Pull out the paper jammed on the bypass tray.

Check beneath the transport guide in the paper feeding area.

Check if any paper is jammed under the transport guide behind the transfer unit.

P .81 “Paper jam behind transfer unit”

80 Paper Jams

Download from Www.Somanuals.com. All Manuals Search And Download.

Paper jam behind transfer unit

Be careful not to let your fingers be caught between the equipment and the side cover.

This could injure you.

Open the side cover.

Pull the transfer unit toward you carefully to lay it down while hold-

ing up the green lever.

Release the jammed paper.

Be sure not to touch the photoconductive drum when releasing the jammed paper.

Paper Jams 81

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Open the transport guide of the paper feeding area and check if any

paper is jammed under this guide. Clear the paper if there is any.

Close the transfer unit and the side cover.

Paper jams within fuser unit

y Be careful not to let your fingers be caught between the equipment and the side cover.

This could injure you.

y Do not touch the fuser unit or the metal part around the unit.

This could cause burns, or injury to your hands if you touch the inside of the equipment.

Open the side cover, and then lay down the transfer unit. Then

press down the two fuser pressure release levers (green) until they

come to a stop.

Press down the levers fully until they stop.

82 Paper Jams

Download from Www.Somanuals.com. All Manuals Search And Download.

Open the transport guide while holding the knob.

Release the jammed paper.

Pull the jammed paper up or down as shown below depending on the position of the

paper.

Be sure not to touch the photoconductive drum when releasing the jammed paper.

Pulling it up

Pulling it down

Return the transport guide to its original position, and then close

the transfer unit and the side cover.

Paper Jams 83

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Paper jams within Paper Feed Unit (optional)

Open the side cover and check if any paper is jammed behind the

transfer unit.

P .81 “Paper jam behind transfer unit”

Open the paper feed cover of the unit.

Release the jammed paper.

Close the paper feed cover of the unit.

Close the side cover.

84 Paper Jams

Download from Www.Somanuals.com. All Manuals Search And Download.

Replacing Toner Cartridge

When the toner in the toner cartridge has run out, replace the toner cartridge following the pro-

cedure below.

y Before inserting a new toner cartridge, check the product name of the cartridge. If you can

see “T-1810”, this cartridge is usable.

y Dispose of used toner cartridges in accordance with local regulations.

y Do not touch the parts on the circuit board mounted on the toner cartridge because they may

be damaged.

Never attempt to incinerate toner cartridges.

Open the front cover.

Hold down the green lever.

The toner cartridge is slightly pushed out.

Replacing Toner Cartridge 85

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Pull out the toner cartridge.

Never attempt to incinerate toner cartridges.

Dispose of used toner cartridges in accordance with local regulations.

Shake the new toner cartridge strongly with the label surface down

to loosen the toner inside.

Remove the protective sheet from the end of the cartridge.

86 Replacing Toner Cartridge

Download from Www.Somanuals.com. All Manuals Search And Download.

Pull out the seal in the direction of the arrow.

Insert the toner cartridge along the rail.

y Before inserting the toner cartridge, check if the green lever is raised and raise it if

not.

y Insert the toner cartridge until you hear a click sound.

Clean the charger.

Hold the cleaning knob of the charger and pull it out toward you carefully until it comes to

a stop. Then reinsert it in its original position carefully. Repeat this procedure two or three

times.

Check if the cleaning knob is fully inserted after cleaning.

After the toner cartridge has been replaced, be sure to clean the transfer charger wire

following the procedure below in order to prevent uneven density of images.

Replacing Toner Cartridge 87

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Open the side cover.

Pull the transfer unit toward you carefully to lay it down while hold-

ing up the green lever.

Remove the transfer charger cleaner from the front pocket of the

transfer unit.

88 Replacing Toner Cartridge

Download from Www.Somanuals.com. All Manuals Search And Download.

Wipe the transfer charger wire with the transfer charger cleaner.

(1) Insert the transfer charger cleaner into the front end of the transfer charger.

(2) Push the cleaner onto the front wall, and then check if the cleaner pad has contacted

with the transfer charger wire.

(3) Clean the wire from its front end to the other end in two reciprocating motions.

(4) Remove the cleaner from the front end of the transfer charger after cleaning.

Return the transfer charger cleaner into the cleaner pocket, and

then close the transfer unit.

Close the side cover.

Close the front cover.

The equipment starts supplying toner.

Replacing Toner Cartridge 89

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Before Calling Service Technician

When you encounter trouble using this equipment, check the items listed below.

General operation

Phenomenon

Usual cause

Countermeasure

The equipment does not

operate at all.

The power of the equipment Turn ON the power of the equipment.

is not turned ON.

The power cable is not

plugged in securely.

Plug in the power cable securely.

The button does not respond It has been a short time

Wait for the completion of warm-up and

then try again.

to my operation.

since the power was turned

ON.

One or more of the message The equipment has detected Check which lamp is lit or blinking and

lamps is lit or blinking.

an error status.

take any countermeasure accordingly.

P .72 “When Message Lamp is Lit/

Blinking”

“– – –” appears on the LED

display.

The access code needs to

be keyed in (when the equip- (For the details of the access code set-

Key in the 3-digit access code.

ment is managed under the

access code function).

The equipment is in the low

power mode.

ting, ask your service technician.)

“ALP” appears on the LED

display.

The equipment enters into the low power

mode after a specified time has passed

since its last use. Copying is enabled.

The equipment enters into the sleep

mode after a specified time has passed

since its last use. For how to cancel this

mode, see the following page.

“SLP” appears on the LED

display.

The equipment is in the

sleep mode.

P .28 “Saving energy when not in use -

Energy saving mode -”

Nothing appears on the LED

display.

The equipment is in the

super sleep mode.

The equipment enters into the super

sleep mode after a specified time has

passed since its last use. For how to can-

cel this mode, see the following page.

P .28 “Saving energy when not in use -

Energy saving mode -”

Scanning stops before it is

finished. (The [START] lamp

is lit and the [FUNCTION

CLEAR] lamp is blinking.)

The number of sheets to be

scanned exceeds the maxi-

mum or the built-in memory

in the equipment becomes

full.

To copy the data scanned so far, press

the [START] button. To delete them, press

the [FUNCTION CLEAR] button.

(When only the [FUNCTION CLEAR]

lamp blinks, only data deletion is possi-

ble.)

Copying stops before it is fin- Approx. 250 sheets of paper Remove the paper from the receiving tray,

ished. (The [START] lamp

and the middle paper jam

have continuously exited and and then press the [START] button. Copy-

the equipment stops copy-

ing to prevent the copied

paper from overflowing from

the tray.

ing resumes. Press the [FUNCTION

CLEAR] button to end the copy job.

position lamp ( ) are lit and

the [FUNCTION CLEAR]

lamp is blinking.)

Printing stops before it is fin-

ished. (The [START] lamp

and the middle paper jam

Approx. 250 sheets of paper Remove the paper from the receiving tray,

have continuously exited and press the [START] button, and then click

the equipment stops printing the [OK] button in the “Out of paper” error

to prevent printed paper from dialog box in the TOSHIBA Viewer. Print-

position lamp ( ) are lit and

the “Out of paper” error dialog

box is displayed in the

overflowing from the tray.

ing resumes.

TOSHIBA Viewer V2.)

90 Before Calling Service Technician

Download from Www.Somanuals.com. All Manuals Search And Download.

Phenomenon

Usual cause

Countermeasure

Even when the equipment is

connected with a PC by a

USB cable, the equipment is

not recognized.

This cable is not certified

according to the USB2.0 Hi-

Speed.

Use a USB2.0 Hi-Speed certified cable.

The equipment is connected When the equipment is connected with a

with a PC via a USB hub.

PC via a USB hub, the equipment may

not be recognized. Connect it with a PC

directly by a USB cable.

Printing, scanning or device

setup cannot be performed

from a PC connected with a

USB cable.

The operation on the left is

performed in the super sleep then back ON, and perform it again.

mode.

Turn the power of the equipment OFF and

If this equipment is connected to your PC

with a USB cable, change the setting so

that it does not enter the super sleep

mode.

P .70 “Changing of the Enabled Energy

Saving Mode”

Toner-related items

Phenomenon

Usual cause

Countermeasure

The toner lamp is lit.

There is only a little toners

remaining in the toner car-

tridge.

There is still some toner in the toner car-

tridge. Do not replace the toner cartridge

until the toner lamp starts blinking.

Install the toner cartridge correctly.

The toner cartridge is not

installed. Or it is not installed

correctly.

A toner cartridge not recom- If you are using a toner cartridge other

mended by TOSHIBA is

being used.

than the one we recommend, the equip-

ment may not be able to detect whether it

is installed or not.

P .9 “Recommended toner cartridges”

Replace the toner cartridge with a new

one.

The toner lamp is blinking.

The toner in the toner

cartridge has run out.

A toner cartridge not recom- If you are using a toner cartridge other

mended by TOSHIBA is

being used.

than the one we recommend, the equip-

ment may not be able to detect whether it

is installed or not.

P .9 “Recommended toner cartridges”

The toner lamp does not light A toner cartridge not recom-

even when the toner has

almost run out.

mended by TOSHIBA is

being used.

The equipment does not

become ready for copying

after the toner cartridge is

inserted.

The toner cartridge inserted

is not usable for this equip-

ment.

Check the product name of the toner car-

tridge. If you can see “T-1810”, this car-

tridge is usable.

Original/Copy paper-related items

Phenomenon

Usual cause

Countermeasure

An original jams.

An original not acceptable for Check if the original is acceptable for the

the equipment is being used. equipment.

P .43 “Precautions for Automatic Docu-

ment Feeder (optional)”

Before Calling Service Technician 91

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Phenomenon

Usual cause

Countermeasure

Copy paper jams.

Copy paper not acceptable

for the equipment is being

used.

Check if the copy paper is acceptable for

the equipment.

P .31 “Paper types not acceptable”

The size of the copy paper in Register the size of the placed copy paper

the drawer or on the bypass properly.

tray is not registered prop-

erly in the equipment.

P .36 “Preparation 3 - Registering Size

of Paper Placed”

P .49 “Bypass copying”

Jammed paper is located in

Use the paper jam position lamp to

a place you cannot see eas- recheck the position where the paper jam

ily.

has occurred.

There is no gap between the Adjust the gap between the side guides

side guides and paper in the and the paper properly.

drawer. Or the gap is too

wide.

P .85 “Replacing T o ner Cartridge”

Multiple feeding occurs.

Paper is clinging to each

other.

Fan the paper well and place it again.

Image trouble

Phenomenon

Usual cause

Countermeasure

The density of the copy

image is light.

Toner has run out.

The toner lamp blinks when toner has run

out. Replace the toner cartridge if it is

blinking.

Make the density darker if you use the

manual copy density mode. Or use the

automatic copy density mode.

The copy density is set

lighter.

The transfer charger wire is

dirty.

Clean the transfer charger wire.

P .98 “Cleaning transfer charger”

Make the density lighter if you use the

manual copy density mode. Or use the

automatic copy density mode.

The density of the copy

image is dark.

The copy density is set

darker.

The copied image is stained. The Automatic Document

Feeder (optional) or the

Platen Cover (optional) is not

lowered fully.

Lower them fully to block outside light.

The original glass, platen

sheet, scanning area or

guides are dirty.

Clean them.

P .98 “Cleaning transfer charger”

The copy density is set

darker.

Make the density lighter if you use the

manual copy density mode. Or use the

automatic copy density mode.

Highly transparent originals

Place a blank sheet of paper, the same

such as OHP films or tracing size as the original or larger, over the orig-

paper are used. inal.

92 Before Calling Service Technician

Download from Www.Somanuals.com. All Manuals Search And Download.

Phenomenon

Usual cause

Countermeasure

The copy image is fogged.

There is a slight gap

between the original glass

and the original.

Lower the Platen Cover (optional) or the

Automatic Document Feeder (optional)

fully so that the original will contact with

the original glass.

The copy paper is damp.

Replace with dry copy paper.

The density level of the copy

image is uneven in a horizon- dirty.

tal direction.

The transfer charger wire is

Clean the transfer charger wire.

The copy image is partially

missing.

The size or direction of the

Use copy paper of the same size as the

original or set the reproduction ratio suit-

able to the copy paper size.

copy paper and the original,

or the reproduction ratio is

not set properly.

The copy image has black

streaks in a horizontal direc-

tion.

The scanning area or guides Clean them.

are stained.