Toshiba Car Video System SD900KY User Manual

Introduction  
Connections  
2
11  
16  
19  
30  
37  
DIGITAL VIDEO  
DVD PLAYER  
Basic playback  
Advanced playback  
Function setup  
Others  
SD900KY  
OWNER’S MANUAL  
© 2009Toshiba Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY INSTRUCTIONS  
1. Read these instructions.  
2. Keep these instructions.  
3. Read all warnings.  
4. Follow all instructions.  
5. Do not use this appliance near water.  
6. Clean only with a dry cloth.  
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including  
amplifiers) that produce heat.  
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the  
point where they exit from the apparatus.  
10. Only use attachments/accessories specified by the manufacturer.  
11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,  
or sold with the apparatus. When a cart is used, use caution when moving the cart/  
apparatus combination to avoid injury from tip-over.  
Portable Cart Warning  
12. Unplug this apparatus during lightning storms or when unused for long periods of  
time.  
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in  
any way, such as the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the  
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.  
ADDITIONALSAFETYINSTRUCTIONS  
14. Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a risk of fire  
or electric shock.  
15. Never expose the apparatus to dripping or splashing or place items such as vases, aquariums, any other item filled  
with liquid, or candles on top of the unit.  
16. Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious personal injury.  
17. Do not place anything on top of this unit.  
18. Do not place the apparatus on amplifiers or equipment that may produce heat.  
19. Never block or cover the slots or openings in the unit.  
Never place the unit:  
• on a bed, sofa, rug or similar surface;  
• too close to drapes, curtains, or walls; or  
• in a confined space such as a bookcase, built-in cabinet, or any other place with poor ventilation.  
The slots and openings are provided to protect the unit from overheating and to help maintain reliable operation.  
20. Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal  
injury and apparatus malfunction.  
21. If the apparatus should emit smoke or an unusual odor, immediately disconnect the power cord from the wall outlet.  
Wait until the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause fire.  
22. During thunderstorms, do not touch the connecting cables or the apparatus.  
23. Warning: To prevent spread of fire, keep candles or other open flames away from this product at all times.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Precautions  
Notes on handling  
Notes on moisture condensation  
When shipping the DVD player, the original shipping  
carton and packing materials come in handy. For  
maximum protection, repack the unit as it was originally  
packed at the factory. Take care not to give it a shock  
or shake when carrying.  
Do not use volatile liquids, such as insect spray, near  
the DVD player.Do not leave rubber or plastic products  
in contact with the DVD player for a long time.They will  
leave marks on the finish.  
Moisture condensation damages the DVD player. Please  
read the following carefully.  
Moisture condensation occurs, for example, when you pour  
a cold drink into a glass on a warm day. Drops of water  
form on the outside of the glass. In the same way, moisture  
may condense on the optical pick-up lens inside this unit,  
one of the most crucial internal parts of the DVD player.  
The top and rear panels of the DVD player may become  
warm after a long period of use. This is not a  
malfunction.  
When the DVD player is not in use, be sure to remove  
the disc and turn off the power.  
If you do not use the DVD player for a long period, the  
unit may not function properly in the future. Turn on  
and use the DVD player occasionally.  
Moisture condensation occurs during the following  
cases.  
Notes on locating  
When you bring the DVD player directly from a cold  
place to a warm place.  
Place the DVD player on a level surface. Do not use it  
on a shaky or unstable surface such as a wobbling  
table or inclined stand. The loaded disc may come off  
the proper position and cause damage to the DVD  
player.  
When you place this DVD player near a TV, radio, or  
VCR, the playback picture may become poor and the  
sound may be distorted. In this case, place the DVD  
player away from the TV, radio, or VCR.  
When you use the DVD player in a room where you  
just turned on the heater, or a place where the cold  
wind from the air conditioner directly hits the unit.  
In summer, when you use the DVD player in a hot and  
humid place just after you move the unit from an air  
conditioned room.  
When you use the DVD player in a humid place.  
Notes on cleaning  
Use a soft, dry cloth for cleaning.  
For stubborn dirt, soak the cloth in a weak detergent  
solution, wring well and wipe. Use a dry cloth to wipe it  
dry.  
Do not use any type of solvent, such as thinners and  
benzene, as they may damage the surface of the DVD  
player.  
Do not use the DVD player when moisture condensation  
may occur.  
If you use a chemical saturated cloth to clean the unit,  
follow that product’s instructions.  
If you use the DVD player in such a situation, it may  
damage discs and internal parts. Remove the disc,  
connect the power cord of the DVD player to the wall  
outlet, turn on the DVD player, and leave it for two or  
three hours. After two or three hours, the DVD player  
will have warmed up and evaporated any moisture.Keep  
the DVD player connected to the wall outlet and  
moisture condensation will seldom occur.  
Inspection and Maintenance  
This DVD player is a high technology, precision device. If  
the optical pick-up lens and disc drive parts become dirty  
or worn down, the picture quality may be reduced. To  
avoid reduction in picture quality, it is recommended that  
regular inspection and maintenance (cleaning or parts  
replacement) be performed every 1,000 hours of use. For  
further details, contact your nearest consumer electronics  
dealer.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes on Discs  
On handling discs  
Structure of disc contents  
Do not touch the playback side of the disc.  
Normally, DVDs are divided into titles, and the titles are  
sub-divided into chapters.VIDEO CDs and audio CDs are  
divided into tracks.  
DVD  
DVD  
Title 1  
Title 2  
Chapter 1 Chapter 2  
Chapter 1 Chapter 2 Chapter 3  
Playback side  
Do not attach paper or tape to discs.  
VIDEO CD/audio CD  
VIDEO CD/audio CD  
Track 2 Track 3 Track 4  
Track 1  
Track 5  
On cleaning discs  
Fingerprints and dust on the disc cause picture and  
sound deterioration. Wipe the disc from the center  
outwards with a soft cloth. Always keep the disc clean.  
Each title, chapter or track is assigned a number, which is  
called “title number”, “chapter number” or “track number”  
respectively.  
There may be discs that do not have these numbers.  
Notes on copyright  
The unauthorized recording, use, distribution, or revision of  
copyrighted materials including, without limitation, television  
programs, videotapes, and DVDs, is prohibited under the  
Copyright Laws of the United States and other countries,  
and may subject you to civil and criminal liability.  
If you cannot wipe off the dust with a soft cloth, wipe  
the disc lightly with a slightly moistened soft cloth and  
finish with a dry cloth.  
Do not use any type of solvent such as thinner, benzine,  
commercially available cleaners or antistatic spray for  
vinyl LPs. It may damage the disc.  
This product incorporates copyright protection technology  
that is protected by method claims of certain U.S. patents  
and other intellectual property rights owned by Macrovision  
Corporation and other rights owners.Use of this copyright  
protection technology must be authorized by Macrovision  
Corporation, and is intended for home and other limited  
viewing uses only unless otherwise authorized by  
Macrovision Corporation. Reverse engineering or  
disassembly is prohibited.  
On storing discs  
Do not store discs in a place subject to direct sunlight  
or near heat sources.  
Do not store discs in places subject to moisture and  
dust such as a bathroom or near a humidifier.  
Store discs vertically in a case. Stacking or placing  
objects on discs outside of their case may cause  
warping.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Notes on Discs (continued)  
About this owner’s manual  
Playable discs  
This owner’s manual explains the basic instructions of this  
DVD player. Some DVDs are produced in a manner that  
allows specific or limited operation during playback. As  
such, the DVD player may not respond to all operating  
commands. This is not a defect in the DVD player. Refer  
to instruction notes of discs.  
This DVD player can play the following discs.  
Maximum  
playback time  
Disc  
Size  
Disc Mark  
Contents  
Approx. 4 hours  
(single sided disc)  
12 cm  
Approx. 8 hours  
Audio  
+
video  
(moving  
pictures)  
(double sided disc)  
” may appear on the TV screen during operation.  
” means that the operation is not permitted by the  
DVDs  
Approx. 80 minutes  
(single sided disc)  
A “  
DVD player or the disc.  
8 cm  
Approx. 160 minutes  
(double sided disc)  
About  
The  
icons on the heading bar show the playable  
discs for the function described under that heading.  
Approx. 74 minutes  
Approx. 20 minutes  
12 cm  
Audio  
+
video  
(moving  
pictures)  
: You can use this function with DVD video discs.  
DVD  
VIDEO  
CDs  
: You can use this function with Video CDs.  
: You can use this function with Audio CDs/CD-R/RW  
CD  
DIGITAL VIDEO  
8 cm  
CDs.  
Approx. 74 minutes  
Approx. 20 minutes  
12 cm  
Notes on region numbers  
Audio  
CDs  
Audio  
8 cm  
(CD  
single)  
The region number of this DVD player is 4. If region  
numbers, which stand for their playable area, are printed  
Audio  
+
video  
(moving  
pictures)  
on your DVD and you do not find  
4
or  
, disc  
35 min.  
10 min.  
12 cm  
8 cm  
SUPER  
VIDEO  
CDs  
playback will not be allowed by the player. (In this case,  
the DVD player will display a message on-screen).  
SUPER VIDEO  
Audio  
+
On VIDEO CDs  
12 cm  
8 cm  
It depends on DivX®  
quality  
DivX®  
video  
(moving  
pictures)  
This DVD player supports VIDEO CDs equipped with the  
PBC (Version 2.0) function. (PBC is the abbreviation of  
Playback Control.) You can enjoy two playback variations  
depending on types of discs.  
The following discs are also available.  
DVD±R/±RW and DVD-ROM discs of DVD format  
CD-R/CD-RW discs of CD-DA,Video CD, MP3 or JPEG  
format  
• VIDEO CD not equipped with PBC function (Version 1.1)  
Sound and movie can be played on this DVD player in  
the same way as an audio CD.  
• VIDEO CD equipped with PBC function (Version 2.0)  
In addition to operation of a VIDEO CD not equipped  
with the PBC function, you can enjoy playback of  
interactive software with search function by using the  
menu displayed on the TV screen (Menu Playback).  
Some of the functions described in this owner’s manual  
may not work with some discs.  
Official DivX® Certified product  
Plays all versions of DivX® video (including DivX® 6) with  
standard playback of DivX® media files  
Some of these discs may be incompatible.  
You cannot play discs other than those listed above.  
You cannot play DVD-RAM discs or non-standardized discs,  
etc., even if they may be labeled as above.  
• This DVD player uses the NTSC/PAL colour system, and  
cannot play DVDs recorded in any other colour system  
(SECAM, etc.).  
Because of problems and errors that can occur during the  
creation of DVD and CD software and/or the manufacture of  
DVD and CD discs,Toshiba cannot assure that this DVD player  
will successfully play every disc bearing the DVD and CD logos.  
If you happen to experience any difficulty playing a DVD and/  
or CD disc on this DVD player, please contactToshiba Customer  
Service.  
is a trademark of DVD Format/Logo Licensing Corporation.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Introduction  
Advanced playback  
SAFETY PRECAUTIONS ........................... 2  
IMPORTANT SAFETY INSTRUCTIONS .... 3  
Precautions ............................................... 4  
Accessing a Specific Location Directly ........... 19  
Locating a specific title/chapter/time ................... 19  
Repeating a Specific Segment................. 20  
Repeating a specific segment ............................ 20  
Notes on Discs .......................................... 5  
Notes on region numbers ................................... 6  
Playing in a Varied Order......................... 20  
Playing titles, chapters or tracks in a varied order .. 20  
Table of Contents...................................... 7  
Playing in a Favourite Order .................... 21  
Setting titles, chapters or tracks in a favourite order .. 21  
Identification of Controls ......................... 8  
Front panel .......................................................... 8  
Rear panel .......................................................... 8  
DVD display ........................................................ 8  
Remote control .................................................... 9  
Loading batteries ............................................... 10  
Operating with the remote control ...................... 10  
Zooming a Picture .................................... 22  
Zooming a picture............................................... 22  
Selecting the Sound Enhancement (E.A.M.) .... 22  
Selecting the sound enhancement...................... 22  
Selecting the Picture Enhancement (E.P.M.) .... 23  
Selecting the picture enhancement..................... 23  
Connections  
Connecting to a TV ................................. 11  
Connecting to a TV (Using the phono type jacks)11  
Connecting to a display (Using a HDMITM cable) 12  
Selecting Subtitles ................................... 23  
Selecting a subtitle language .............................. 23  
Selecting the Camera Angle .................... 24  
Changing the camera angle ................................ 24  
Connecting to Optional Equipment ....... 13  
Selecting a Language ............................... 24  
Selecting a playback audio setting ..................... 24  
Connecting to an amplifier equipped with a  
Dolby® Digital decoder ......................................... 14  
On-screen Display Operation .................. 25  
On-screen display operation .............................. 25  
Connecting to an amplifier equipped with  
Dolby Surround Pro Logic ................................ 14  
Connecting to an amplifier equipped with a  
DTS® decoder .................................................. 15  
Connecting to an amplifier equipped with an MPEG2  
audio decoder .................................................. 15  
Playing MP3 Files ..................................... 26  
Playing MP3 files................................................ 26  
Viewing JPEG Files .................................. 27  
Viewing JPEG files ............................................ 27  
Viewing a thumbnail view ................................... 27  
Connecting to an amplifier equipped with a  
digital audio input .............................................. 15  
Playing DivX®/MPEG-4 Files .................... 28  
Playing DivX®/MPEG-4 files ............................... 28  
Basic playback  
Playing USB Device .................................. 29  
Playing a Disc ......................................... 16  
Connecting to USB flash drive ........................... 29  
Basic playback ................................................ 16  
Variable Speed Playback ........................ 17  
Playing in fast reverse or fast forward directions .. 17  
Playing frame by frame .................................... 17  
Playing in slow-motion...................................... 17  
Resuming playback from the same location ..... 17  
Function setup  
Customizing the Function Settings ........ 30  
Setting procedure ............................................... 30  
Setting details..................................................... 30  
Locating a Desired Section .................... 18  
Locating a title using the top menu..................... 18  
Locating a specific chapter or track .................. 18  
Others  
Table of Languages................................... 37  
Before Calling Service Personnel ........... 38  
Specifications ........................................... 39  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Identification of Controls  
See the page in  
for details.  
Front panel  
16  
16  
10  
USB jack  
HDMI SELECT  
8
29  
12  
16  
16  
HDMI indicator  
12  
16  
Rear panel  
HDMI OUT  
Power Cord  
11  
12  
jack  
VI
HDMI OUT  
HDMI OUT  
11  
14  
15  
DVD display  
The indicators vary depending on the kinds of discs you play.  
Bad disc  
Bad disc  
No disc  
OPEN  
LOAD/CLOSE  
Power off  
Chapter/Track  
number Indicator  
DVD VIDEO  
VIDEO CD  
Audio CD  
Picture  
• During playback:  
Example  
• During playback:  
Example  
• During playback:  
Example  
• During thumbnail  
viewing  
Multifunctional indicator  
(indicates operating  
status or messages, etc.)  
Some discs may only  
display chapter numbers.  
Some discs may only  
display track numbers.  
Some discs may only  
display track numbers.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Identification of Controls (continued)  
The instructions in this manual describe the functions on the remote control. See the page in  
for details.  
Remote control  
16  
16  
19  
19  
22  
23  
17  
23  
24  
24  
16  
17  
16  
18  
17  
18  
17  
18  
18  
25  
16  
25  
18  
20  
19  
16  
16  
20  
21  
30  
22  
USB  
DVD  
HDMI button 12  
USB button  
DVD button  
29  
29  
* RETURN button  
Return to menu display forVCD (2.0) discs with menu.  
* MENU button  
Use the MENU button to display the menu included on  
many DVDs. To operate a menu, follow the instructions  
in “Locating a title using the top menu.”  
18  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Identification of Controls (continued)  
Loading batteries  
Operating with the remote control  
Open the cover.  
Point the remote control at the remote  
sensor and press the buttons.  
1
Insert batteries (R03/AAA size).  
2
Distance: About 7 m (23 feet) from the front of the  
remote sensor  
Angle:  
About 30° in each direction of the front of  
the remote sensor  
* Do not expose the remote sensor of the DVD player  
to a strong light source such as direct sunlight or  
other illumination. If you do so, you may not be able  
to operate the DVD player via the remote control.  
Make sure to match the + and – on the batteries  
to the marks inside the battery compartment.  
Notes on the remote control  
• Direct the remote control at the remote sensor of the DVD  
player.  
Caution  
Never throw batteries into a fire.  
• When using the remote control, press the buttons at intervals  
of about 1 second to ensure the correct mode of operation.  
• Do not drop or give the remote control a shock.  
• Do not leave the remote control near an extremely hot or  
humid place.  
Notes  
• Be sure to use R03/AAA size batteries.  
• Dispose of batteries in a designated disposal area.  
• Batteries should always be disposed of with the environment  
in mind. Always dispose of batteries in accordance with  
applicable laws and regulations.  
• If the remote control does not operate correctly, or if the  
operating range becomes reduced, replace both batteries with  
new ones.  
• Do not spill water or put anything wet on the remote control.  
• Do not open the remote control.  
• When necessary to replace batteries in the remote control,  
always replace both batteries with new ones. Never mix battery  
types or use new and used batteries in combination.  
• Always remove batteries from remote control if they are dead  
or if the remote control is not to be used for an extended  
period of time.This will prevent battery acid from leaking into  
the battery compartment.  
• Battery shall not be exposed to excessive heat such as  
sunshine, fire or the like.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a TV  
Connect the DVD player to your TV.  
Connecting to aTV (Using the phono type jacks)  
V
Normal TV  
HDMI OUT  
To VIDEO  
OUT  
To 2ch AUDIO OUT  
(R: red, L:white)  
(yellow)  
To audio  
input  
To video  
input  
(yellow)  
• Make the following setting.  
On-screen display Select:  
Page  
Audio/Video cables (supplied)  
“Off”,  
“Digital Output”  
34  
“PCM” or  
“Bitstream”  
Composite  
“Video Out”  
33  
HDMI  
Notes  
• Refer to the owner’s manual of the connected TV as well.  
• When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet  
before making any connections.  
• If your television set has one audio input, connect the left and right audio outputs of the DVD player to a Y cable  
adapter (not supplied) and then connect to your TV.  
• Connect the DVD player directly to your TV. If you connect the DVD player to a VCR, TV/VCR combination or video  
selector, the playback picture may be distorted as DVDs are copy protected.  
• Analogue audio out will not have sound if DTS playback is selected.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections  
About HDMI  
HDMI has the capability to support standard, enhanced, or  
high-definition video plus standard to multi-channel surround-  
sound audio. HDMI features included uncompressed digital  
video, a bandwidth of up to 2.2 gigabytes per second (with HDTV  
signals), one connector (instead of several cables and connectors),  
and communication between the AV source and AV devices such  
as DTVs.  
HDMI, the HDMI logo and High-Definition Multimedia Interface  
are trademarks or registered trademarks of HDMI licensing  
LLC.  
HDMI (High Definition Multimedia Interface) supports both video  
and audio on a single digital connection for use with DVD players,  
DTV, set-top boxes, and other AV devices.HDMI was developed  
to provide the technologies of High Bandwidth Digital Content  
Protection (HDCP) as well as Digital Visual Interface (DVI) in  
one specification. HDCP is used to protect digital content  
transmitted and received by DVI-compliant or HDMI-compliant  
displays.  
Connecting to a display (Using a HDMITM cable)  
V
HDMI OUT  
To HDMI  
Output  
HDMI Cable  
(not supplied)  
Available output signals are below:  
Auto  
HDMI-compatible display  
576p/480p (progressive)  
720p (progressive)  
1080i (interlaced)  
1080p (progressive)  
• Make the following setting.  
Switching the video quality (HDMI mode) using the  
HDMI button on the remote control or the HDMI  
SELECT button on the front panel.  
Press HDMI button on the remote control or HDMI SELECT  
button on the front panel to receive a suitable video quality in  
STOP mode. The video quality is required to match your TV  
having HDMI feature and suitable quality. Please also check  
yourTV owner’s manual.  
On-screen display  
“Digital Output”  
Page  
Select:  
“PCM”  
34  
“Video Out”  
HDMI  
33  
Notes  
• Refer to the owner’s manual of the connected TV as well.  
• When you connect the DVD player to yourTV, be sure to turn off  
the power and unplug both units from the wall outlet before making  
any connections.  
• If you have a HDMI (with HDCP) equipped monitor or display,  
you can connect it to this player using a HDMI cable.  
• The HDMI connector outputs uncompressed digital video, as  
well as almost every kind of digital audio that the player is  
compatible with, including DVD-Video, Video CD/Super VCD,  
CD, MP3 and DivX®.  
• This unit has been designed to be compliant with HDMI (High  
Definition Multimedia Interface) depending on the component  
you have connected. Using a HDMI connection may result in  
unreliable signal transfers.  
• Because HDMI is an evolving technology, it is possible that  
some devices with an HDMI input may not operate properly  
with this DVD player.  
Press this button to change the output signals as below. See  
the HDMI indicator and select the appropriate output signal.  
HDMI indicator  
Video output signal  
1080p (progressive)  
illuminates “ • 1080p”  
Press  
illuminates “ • 1080i”  
1080i (interlaced)  
720p (progressive)  
Press  
illuminates “ • 720p”  
Press  
illuminates “ • 576p/480p”  
Press  
576p/480p (progressive)  
illuminates “ • 576p/480p,  
• 720p, • 1080i and • 1080p”  
Auto  
• When using HDMI cable, do not connect to other analogue video  
outputs.  
Press  
• No sound will be output from the HDMI cable if the digital out  
is not set to PCM.  
• HDMI output is only available when the Video Out is set to  
“HDMI”. Otherwise the HDMI button is invalid.  
576p/480p, 720p, 1080i and 1080p are signals created with  
this DVD Player from original 576i/480i signal.The resolution  
of the picture may not be increased even if they are selected.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Content of the output for each output jack is shown in the following table and differ depending on the On-Screen  
Display Setting:  
HD JPEG Mode: Off  
Content of output for  
each output jack  
HD JPEG Mode: On  
Content of output for each  
output jack during JPEG playback  
On-Screen Display Setting  
"Video Out" HDMI Output  
HDMI  
Output  
-
Video  
HDMI  
Output  
-
Video  
Setting  
Setting *  
Invalid  
480/576p  
720p  
Output  
Output  
Composite  
Composite  
Composite  
Composite  
Composite  
Composite  
Composite  
480p/576p  
720p  
480p/576p  
720p  
Composite  
-
-
-
HDMI  
1080i  
1080i  
1080i  
1080p  
1080p  
1080p  
* Settings for HDMI output format are performed using the HDMI button on the remote control or HDMI SELECT button  
on the front panel.  
Notes  
Composite (Video) will not have JPEG pictures output when HD JPEG Mode is on  
resolution mode. You may view photos (JPEG ) through HDMI connection.  
, except 480p/576p video  
32  
• If Auto is selected, it follows preference HDMI aspect ratio of TV.  
Connecting to Optional Equipment  
You can enjoy high quality dynamic sounds by connecting the DVD player to optional audio equipment.  
• For connection to yourTV, see “Connecting to aTV.  
• This section uses the following reference marks.  
Warning  
• When you are connecting (via the COAXIAL DIGITAL  
AUDIO OUT jack) an AV decoder that does not have Dolby  
Digital, DigitalTheater Systems (DTS) or MPEG2 decoding  
function, be sure to set “Digital Output” to “PCM” from the  
on-screen displays. Otherwise, high volume sound may  
damage your hearing as well as the speakers.  
• When playing DTS-encoded discs (DVDs and audio CDs),  
excessive noise may be output from the analog audio output  
jacks. To avoid possible damage to the audio system, you  
should take proper precautions when the analog audio output  
jacks of the DVD player are connected to an amplification  
system. To enjoy DTS Digital Surround™ playback, an  
external 5.1 channel DTS Digital Surround™ decoder  
system must be connected to the COAXIAL DIGITAL  
AUDIO OUT jack of the DVD player.  
: Front speaker  
: Rear speaker  
: Sub woofer  
: Center speaker  
: Signal flow  
Notes  
• DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the AC-3 RF input of a Dolby Digital Receiver. This  
input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO OUT jack  
of the DVD player.  
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to theDIGITAL (COAXIAL)input of a Receiver or Processor.  
• Refer to the owner’s manual of the connected equipment as well.  
• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall  
outlet before making any connections.  
• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening  
level. Otherwise, the speakers may be damaged by a sudden high volume sound.  
Turn off the amplifier before you connect or disconnect the DVD player’s power cord. If you leave the amplifier power on, the  
speakers may be damaged.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections  
Connecting to Optional Equipment (Continued)  
Connecting to an amplifier equipped with a Dolby® Digital decoder  
Dolby Digital  
Manufactured under license from Dolby  
Dolby Digital is the surround sound technology used in theaters showing the latest  
movies, and is now available to reproduce this realistic effect in the home.You can  
enjoy motion picture and live concert DVDs with this dynamic realistic sound by  
connecting the DVD player to a 6 channel amplifier equipped with a Dolby Digital  
decoder or Dolby Digital processor.If you have a Dolby Surround Pro Logic decoder,  
you will obtain the full benefit of Pro Logic from the same DVD movies that provide  
full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby  
Surround mark.  
Laboratories. Dolby and the double-D  
symbol are trademarks of Dolby  
Laboratories.  
• Use DVDs encoded via the Dolby  
Digital recording system.  
• Make the following setting.  
On-screen display  
“Digital Output”  
Select:  
Page  
VIDEO  
L
Amplifier equipped with a  
Dolby Digital decoder  
“PCM” or  
“Bitstream”  
34  
OXIIIA
To COAXIAL  
type digital  
audio input  
To COAXIAL  
DIGITAL  
AUDIO OUT  
To wall  
outlet  
75 coaxial cable (not supplied)  
Connecting to an amplifier equipped with Dolby Surround Pro Logic  
Dolby Surround Pro Logic  
• Make the following setting.  
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting  
an amplifier and speaker system (right and left front speakers, a center speaker,  
and one or two rear speakers).  
On-screen display  
Select:  
Page  
“PCM” or  
“Bitstream”  
“Digital Output”  
34  
With an amplifier equipped with Dolby Digital  
Connect the equipment the same way as described in “Connecting to an amplifier  
equipped with a Dolby® Digital decoder.Refer to that amplifier’s owner’s manual  
and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.  
With an amplifier not equipped with Dolby Digital  
Connect the equipment as follows.  
* Connect one or two rear speakers.  
The output sound from the rear speakers will  
be monaural even if you connect two rear  
speakers.  
VI
Amplifier equipped with  
Dolby Surround Pro Logic  
II
L
To audio  
input  
To ANALOG  
AUDIO OUT  
To wall  
outlet  
Audio cable (not supplied)  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to an amplifier equipped with a DTS® decoder  
Digital Theater Systems (DTS)  
DTS is a high quality surround technology used in theaters and now available for  
home use, on DVDs or audio CDs.  
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1  
channel DTS encoded sound tracks on DVDs or audio CDs.  
Manufactured under license under U.S.  
Patent #: 5,451,942 & other U.S. and  
worldwide patents issued & pending. DTS  
and DTS Digital Out are registered  
trademarks and the DTS logos and  
Symbol are trademarks of DTS, Inc. ©  
1996-2008 DTS, Inc. All Rights Reserved.  
Amplifier equipped with a  
DTS decoder  
L
VIDEO  
I
AL
• Use DVDs or audio CDs encoded  
via the DTS recording system.  
• Make the following setting.  
To COAXIAL  
type digital  
audio input  
To COAXIAL  
DIGITAL  
AUDIO OUT  
To wall  
outlet  
On-screen display  
“Digital Output”  
Select:  
Page  
34  
“Bitstream”  
75 coaxial cable (not supplied)  
Connecting to an amplifier equipped with an MPEG2 audio decoder  
MPEG2 sound  
You can enjoy motion picture and live concert DVDs with dynamic realistic sound  
by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2  
audio processor.  
• Use DVDs encoded via the MPEG2  
recording system.  
• Make the following setting.  
On-screen display  
“Digital Output”  
Select:  
Page  
Amplifier equipped with an  
MEPG2 audio decoder  
“PCM” or  
“Bitstream”  
34  
III
To COAXIAL  
type digital  
audio input  
To COAXIAL  
DIGITAL  
AUDIO OUT  
To wall  
outlet  
75 coaxial cable (not supplied)  
Connecting to an amplifier equipped with a digital audio input  
2 channel digital stereo  
• Make the following setting.  
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an  
amplifier equipped with a digital audio input and speaker system (right and left front  
speakers).  
On-screen display  
Select:  
Page  
34  
“Digital Output”  
“PCM”  
VDEO  
L
Amplifier equipped with  
a digital audio input  
I
To COAXIAL  
type digital  
audio input  
To COAXIAL  
DIGITAL  
AUDIO OUT  
To wall  
outlet  
75 coaxial cable (not supplied)  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic playback  
CAUTION  
Playing a Disc  
Keep your fingers well clear of the disc tray as it is closing.  
Neglecting to do so may cause serious personal injury.  
This section shows you the basics on how to play a disc.  
Basic playback  
Preparations  
To obtain a higher quality picture  
• When you want to view a disc, turn on the TV and select the  
video input connected to the DVD player.  
• When you want to enjoy the sound of discs from the audio  
system, turn on the audio system and select the input connected  
to the DVD player.  
Occasionally, some picture noise not usually visible during  
a normal broadcast may appear on the TV screen while  
playing a DVD because the high resolution pictures on these  
discs include a lot of information. While the amount of noise  
depends on the TV you use with this DVD player, you should  
generally reduce the sharpness adjustment on yourTV when  
viewing DVDs.  
Press the ON/STANDBY button on the  
front panel or the POWER button on the  
1
To start playback in the stop mode  
Press PLAY.  
remote control.  
POWER  
The DVD player turns on.  
Press OPEN/CLOSE.  
2
To pause playback (still mode)  
Press PAUSE/STEP during playback.  
The disc tray opens.  
To resume normal playback, press the  
PLAY button.  
• The sound is muted during still mode.  
Place the disc on the disc tray.  
3
To stop playback  
Press STOP.  
With the playback side  
down  
• There are two different disc sizes. Place the disc in  
the correct guide on the disc tray. If the disc is out of  
the guide, it may damage the disc and cause the DVD  
player to malfunction.  
• Do not place a disc which is unplayable in this DVD  
player.  
To remove the disc  
Press OPEN/CLOSE.  
Remove the disc after the disc tray  
opens completely.  
Be sure to press the OPEN/CLOSE  
button to close the disc tray after you  
remove the disc.  
Press OPEN/CLOSE to close the disc tray.  
4
Playback starts.  
To turn the power off  
Press ON/STANDBY on the front panel or POWER  
button on the remote control to turn the unit off.  
If you insert a DVD that contains a top menu, a  
menu may appear. Use  
/
/
/
to select the  
title you want to view, then press ENTER to start  
playback.  
Automatic Power Off function  
If the DVD player is stopped, or the screen saver is engaged  
for approximately 20 minutes, the DVD player will  
automatically turn itself off.  
You may need to press the TOP MENU or MENU  
button to display disc menu (depending on the actual  
DVD.)  
Notes  
• Do not move the DVD player during playback.Doing so may damage  
the disc.  
Notes  
• If the disc tray is holding a disc you have already played,  
• Use the OPEN/CLOSE button to open and close the disc tray.  
Do not push the disc tray while it is moving. Doing so may cause  
the DVD player to malfunction.  
• Do not push up on the disc tray or put any objects other than  
discs on the disc tray. Doing so may cause the DVD player to  
malfunction.  
• In many instances, a menu screen will appear after playback of  
a movie is completed. Prolonged display of an on-screen menu may  
damage your television set, permanently etching that image onto its  
screen. To avoid this, be sure to press the STOP button on your  
remote control once the movie is completed.  
playback will begin from the location where you last stopped.  
17  
For resuming playback, see  
.
• Some video CD are recorded with PBC (Playback Control), a menu  
with recorded contents may appear on the TV if you have turned  
the PBC on. You can make your selection according to its PBC  
menu. Press the PBC button on the remote control to turn PBC on  
or off anytime during Video CD playback. When switching from  
PBC off to PBC on mode, playback will start from the beginning of  
the disc. To turn on the menu display again, press the RETURN  
button.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Variable Speed Playback  
You can play discs at various speeds, and resume playback from the location where you stopped playback.  
Playing in fast reverse or fast forward directions  
To resume normal playback  
Press PLAY.  
Press REV or FWD during playback.  
REV: Fast reverse playback  
FWD: Fast forward playback  
Notes  
Each time you press the REV or FWD  
button, the playback speed changes.  
• The DVD player mutes sound and subtitles during reverse  
and forward scan of DVDs.  
• The playback speed may differ depending on the disc.  
Playing frame by frame  
To resume normal playback  
Press PLAY.  
Press PAUSE/STEP during still playback.  
Each time you press the PAUSE/STEP  
button, the picture advances one  
frame.  
Note: The sound is muted during frame by frame playback.  
Playing in slow-motion  
To resume normal playback  
Press PLAY.  
Press SLOW during playback.  
Each time you press the SLOW  
button, the slow-motion speed  
changes in the following sequence:  
Notes  
• The sound is muted during slow-motion playback.  
• 3 speeds are available.  
Resuming playback from the same location  
Notes  
Press STOP at the location where you  
want to interrupt playback.  
• There may be a difference in the location where playback  
resumes depending on the disc.  
• Settings you changed using the on-screen displays while  
the DVD player keeps a location in the memory may function  
only after the memory is cleared.  
1
2
The DVD player memorizes the  
location where playback is stopped.  
• Resuming playback does not work for VCD with PBC on.  
Press PLAY.  
The DVD player resumes playback  
from the location where you stopped  
playback.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic playback  
To start playback from the beginning regardless of the location where you stopped playback.  
1
Press STOP twice.  
If you want to return to the  
beginning of a DVD, open  
and close the disc tray once  
with the OPEN/CLOSE  
button before pressing the  
PLAY button.  
The DVD player deletes the memory of the location.  
2
Press PLAY.  
Playback starts from the beginning of the current title.  
Playback starts from the beginning of the disc.  
Playback starts from the beginning of the current track.  
Locating a Desired Section  
Normally, DVDs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs are divided into  
tracks.You can quickly locate any specific title, chapter, or track.  
Locating a title using the top menu  
PressTOP MENU.  
Press ENTER.  
1
2
3
The top menu appears on the TV  
screen.  
Playback starts from chapter 1 of the  
selected title.  
e.g.  
Notes  
• The instructions above describe basic procedures which may  
vary depending on the contents of the DVD. If different  
instructions appear on theTV screen, follow those instructions.  
• If you display the top menu during playback and press the TOP  
MENU button again without selecting any title, the DVD player  
may resume playback from the point where you first pressed  
theTOP MENU button (depending on the actual DVD.)  
• This method of locating a title is available only on a disc that  
contains a top menu.  
Press  
want.  
/
/
/
to select the title you  
If the titles in the top menu are assigned  
a number, you can directly locate a  
specific title by pressing its designated  
number with the number buttons.  
• Instruction notes of discs may refer to the button that displays  
the top menu as TITLE button.  
Locating a specific chapter or track  
Note  
Press SKIP  
the chapter or track number you want.  
or  
repeatedly to access  
Some titles may not display chapter numbers.  
Playback starts from the selected chapter or track.  
To locate succeeding chapters or tracks.  
Playback starts from the beginning of the  
current chapter or track.  
When you press twice in quick  
successions, playback starts from the  
beginning of the preceding chapter or track.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessing a Specific Location Directly  
Locating a specific title/chapter/time  
Accessing chapters/tracks using number  
buttons:  
PressT.  
1Press  
SEARCH  
For chapter/track numbers 10 to 19, press +10 once  
and the number 10 appears then enter the second digit.  
Press ENTER.  
For chapter/track numbers 20 to 29, press +10 twice  
and the number 20 appears then enter the second digit.  
Press ENTER.  
/
to highlight the Title/Chapter/  
Track/Time.  
e.g.  
T
1
For example, if you want to select chapter/track 25, first  
press +10 twice then press the number button “5”.Then  
press ENTER.  
00 : 00 : 00  
Track  
2
Accessing the time using number buttons:  
Just enter 2 digits in order.  
Time  
00 : 00 : 00  
Disc Time  
The first two numbers you entered represent hours.  
The second two numbers you entered represent  
minutes.  
The third two numbers you entered represent seconds.  
Press  
/
to select a section you want to  
locate.  
2
To set and play favourite bookmark during playback  
1.PressT twice, the display of Bookmark appears, then  
press ENTER to mark the desired scene.  
SEARCH  
e.g. When you want to locate a chapter.  
T
1
Bookmark  
00 : 00 : 00  
Or  
Press the number buttons to enter title,  
chapter (track) number or time.  
2. Press ENTER to play the favourite bookmark.  
To set other bookmarks.  
Follow step 1 and move through the menu by pressing  
the or button.  
Press T again to remove this display.  
Press ENTER.  
3
To cancel the Bookmark  
Playback starts from the selected  
section.  
Follow step 1, then press the CLEAR button to cancel the  
bookmark. Move through the menu by pressing the or  
button to cancel other bookmarks.  
Notes  
• Some discs may not work with marking operation.  
• The marking is cancelled when you open the disc tray or turn  
the power off.  
• Some subtitles recorded around the marker may fail to  
appear.  
Notes  
• Pressing the CLEAR button resets the numbers. To clear  
the display, press the T button several times.  
• For VCD with PBC on, accessing tracks using number  
buttons does not work.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced playback  
Repeating a Specific Segment  
You can specify a desired segment and repeat it.  
Repeating a specific segment  
To resume normal playback  
Press A-B RPT until RepAB Off is displayed.  
Press A-B RPT at the beginning of the  
segment (point A) you want to play  
1
A-B RPT  
repeatedly.  
A-B RPT  
RepAB Off  
Rep A-  
Notes  
• Some discs may not permit A-B repeat operation.  
You cannot set the A-B repeat function for a segment that  
includes multiple camera angles.  
You can specify a segment only within the current title or track  
(VIDEO CD).  
• There may be a slight difference between point A and the  
location where playback actually resumes depending on the  
disc.  
Press A-B RPT again at the end of the  
segment (point B).  
2
A-B RPT  
The DVD player automatically returns to  
point A and starts repeat playback of the  
selected segment (A-B).  
Rep A-B  
Playing in a Varied Order  
You can play titles, chapters within a title, or tracks in a varied order.  
For Audio CD, please see “Playing MP3 files”  
.
26  
Playing titles, chapters or tracks in a varied order  
Press PLAY MODE.  
Press PLAY.  
1
2
PLAY MODE  
Press  
/
button to select desired  
Press the PLAY button, the DVD  
player starts playback in the selected  
mode.  
features and then press ENTER button  
to toggle desired mode.  
e.g.  
Play Mode  
Mode  
Normal  
: Off  
Repeat  
To resume normal playback  
Press ENTER until the Off/Normal is displayed.  
Normal  
Shuffle  
Chapter  
Title  
Single  
PBC  
(VCD only)  
Note  
Some discs may not permit these operations.  
Shuffle: Playbacks in random order.  
PBC: Playbacks in PBC On mode (VCD only).  
Chapter: Repeats the current chapter.  
Title: Repeats the current title.  
Single: Repeats the current track.  
All:  
Off:  
Repeats the entire disc.  
Resumes normal playback.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playing in a Favourite Order  
You can combine your favourite titles, chapters, or tracks and play them in the order you determine.You can program up to  
12 selections into the memory. (Memory playback)  
Setting titles, chapters or tracks in a favourite order  
To change the programmed selections  
1. While the display appears on the TV screen, press  
Insert a disc and press MEMORY during  
stop.  
1
/
/
/
to move the highlighted bar to the item  
The following display appears.  
e.g. DVD  
you want to change, then press CLEAR.  
2. Press number buttons to input the new title/chapter/  
track number.  
MEMORY  
Memory  
To cancel the programmed selections  
Title Chapter  
1. While the display appears on the TV screen, press  
Play  
/
/
/
to move the highlighted bar to the item  
you want to cancel.  
2. Press CLEAR.  
All  
Chapter number  
Title number  
To resume normal playback from memory  
playback  
Press MEMORY button.  
e.g. VCD  
Press  
/
/
/
to move the highlighted bar to “Clear  
All”, then press ENTER. All the input programs will be  
cleared.  
Memory  
Press PLAY button to resume normal playback.  
Play  
All  
DVD: Normal playback will start from current  
playback.  
Track number  
VCD: Normal playback will start from the  
beginning of the disc.  
Select the items in the order you want by  
pressing the number buttons.  
To program during playback  
If you press the MEMORY button during playback, a  
programming display appears.  
2
3
Each time you press the  
/
/
/
button, the  
space is highlighted in turn.Highlight where you want  
to enter, then press the corresponding number  
buttons.  
Follow steps 2 and 3.  
Notes  
To select another chapter in the same title, you need  
to select the title number.  
• Some discs may not permit memory playback operation.  
• If you select repeat during memory playback, the DVD player  
repeats the current memory playback.  
• If you press the MEMORY button while the display appears  
on the TV screen, the display disappears.  
To select tracks from aVIDEO CD/audio CD in order,  
press the number buttons for the track.  
• The programmed selections will be cleared when you open  
the disc tray or turn off the DVD player.  
Press  
/
/
/
to move the highlighted  
bar to Play, then press the ENTER.  
The DVD player starts memory  
playback.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced playback  
Zooming a Picture  
You can magnify areas within a picture.  
Zooming a picture  
To resume normal playback  
Press ZOOM during normal, slow or still  
playback.  
Off  
Press ZOOM repeatedly until the  
Original picture is restored.  
is displayed.  
The centre part of the image will be  
ZOOM  
ZOOM  
zoomed in.  
e.g.  
2
Notes  
• Some discs may not respond to zoom feature.  
• During some scenes, the buttons may not work as described.  
• Zooming does not work on subtitles or menus included on  
DVDs.  
Each time you press the ZOOM button, the magnification  
level changes as follows:  
• The magnification level varies depending on the picture size  
you select.  
1
2
3
Off  
Press the ZOOM button to select the magnification level.  
Press the buttons to view a different part of the  
/
/
/
image.You may move the image from the centre position to  
UP, DOWN, LEFT and RIGHT direction.  
When you reach the edge of the image, the display will not  
shift anymore in that direction.  
Selecting the Sound Enhancement (E.A.M.*)  
You can easily switch a preferred audio enhancement.  
*E.A.M.: Enhanced Audio Mode  
Selecting the sound enhancement  
To exit the audio enhancement selection  
Press E.A.M.  
E.A.M.  
1
Leave the DVD player unattended for about a few  
seconds after having made a selection.  
The sound enhancement will appear:  
3D effect  
Press the E.A.M. button again, the sound enhancement Notes  
change to Off.  
• Actual effects to sounds may vary depending on the speaker  
system. Make selection according to your preference.  
• Actual effects to sounds may vary depending on the disc.  
• When the DVD player is connected to an amplifier equipped  
with Dolby Surround Pro Logic, select “3D effect”. Otherwise,  
Dolby Surround Pro Logic may function differently than usual.  
3D*:  
To obtain expansive virtual surround sound effects  
from two speakers.  
To use this enhancement on sounds output from the  
ANALOG AUDIO OUT jacks, be sure to set “Digital  
Output” to “PCM”.  
* Effective in playback of a DVD.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the Picture Enhancement (E.P.M.*)  
You can easily select a preferred picture enhancement.  
*E.P.M.: Enhanced Picture Mode  
Selecting the picture enhancement  
To exit the picture enhancement selection  
Press E.P.M. again.  
Press E.P.M.  
1
E.P.M  
E.P.M  
The picture enhancement menu  
appears.  
1
6
1
1
12  
12  
Note  
Contrast  
Actual effect to picture may vary depending on the TV. Make  
selection according to your preference.  
Select the picture enhancement by  
2pressing  
/
, then press  
/
to make  
your selections.  
Each time you press the  
/
button, the picture  
enhancement changes.  
Selecting Subtitles  
You can display subtitles on the TV screen and  
select a subtitle language from those included on  
the DVD.  
Selecting a subtitle language  
Press SUBTITLE during playback.  
SUBTITLE  
Press SUBTITLE while the subtitle setting  
is displayed on the TV screen.  
2
1
The current subtitle setting is  
displayed.  
Each time you press the SUBTITLE  
button, the subtitle languages included  
on the DVD change.  
e.g.  
e.g.  
To turn subtitles on or off  
To turn off the subtitle setting display,  
press the SUBTITLE button repeatedly  
Off  
1. Press SUBTITLE during playback.  
2. Press SUBTITLE repeatedly until the  
displayed.  
Off  
is  
until  
is displayed.  
Notes  
Notes  
• Some DVDs are set to display subtitles automatically, and  
you cannot turn them off even if you set the subtitle function  
to off.  
• During some scenes, the subtitles may not appear  
immediately after you select your desired language.  
• Some DVDs will allow you to make subtitle selections and  
turn subtitles on or off only via the disc menu.  
• When you turn on the DVD player or replace a disc, the player  
returns to the initial default setting.  
• When you select a subtitle language which is not included on  
the disc, the DVD player plays a prior language programmed  
on the disc.  
• During some scenes, the subtitles may not appear  
immediately after you change the subtitle language.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced playback  
Selecting the Camera Angle  
If the scene was recorded from multiple angles,  
you can easily change the camera angle of the  
scene you are watching.  
Changing the camera angle  
Press ANGLE while the angle number  
is displayed on theTV screen.  
Press ANGLE while playing a scene  
recorded with multiple angles.  
2
1
ANGLE  
ANGLE  
Press the ANGLE button repeatedly  
While playing a scene recorded with  
to change the scene to the next angle  
in those recorded.  
multiple angles, press the ANGLE  
button.  
e.g.  
About two seconds later, playback  
continues from the new angle you  
selected.  
If no button is pressed within 10  
seconds, playback continues  
without changing the current angle.  
Number changes to show the number  
of the current angle. (The maximum  
number of possible angles is 9)  
To resume normal playback  
Press ANGLE repeatedly until the “  
” is displayed.  
1/3  
Notes:  
This function can only be used for discs on which scenes shot from multiple angles have been recorded.  
If only one angle is recorded, “ ” is displayed.  
1/1  
Selecting a Language  
You can select a preferred language and sound  
recording system from those included on the DVD.  
Selecting a playback audio setting  
Notes  
Press AUDIO during playback.  
• When you turn on the DVD player or replace a disc, player  
returns to the initial default setting.  
If you select a sound track which is not included on the disc,  
the DVD player plays a prior sound track programmed on the  
disc.  
• Some discs allow you to change audio selections only via  
the disc menu. If this is the case, press the MENU button  
and choose the appropriate language from the selections  
on the disc menu.  
1
2
AUDIO  
The current audio setting is displayed.  
e.g.  
Recorded audio format number changes  
sequentially. (The maximum number of  
possible audio formats is 8.)  
Selecting sound channels ofVIDEO CDs  
If the abbreviation of the language appears instead  
of the language name. Refer to the list of languages  
and their abbreviations  
Press AUDIO repeatedly during  
AUDIO  
playback to hear a different audio  
channel (Stereo, Left, Right or Mix).  
.
37  
Press AUDIO while the audio setting is  
displayed on theTV screen.  
Each time you press the AUDIO  
button, the audio settings included on  
the DVD change.  
AUDIO  
The audio setting display will disappear after a few  
seconds.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On-screen Display Operation  
When you turn on the on-screen display, you can view information on operational status and access features and settings.  
On-screen display operation  
Press NAVI.  
NAVI  
The following display appears.  
e.g. When playing a DVD.  
Select by pressing  
then press ENTER to  
access the feature.  
/
Chapter number  
00:30:34/01:00:52 1/1 5/12  
Elapsed time  
Remaining time  
Title number  
Features  
:
To start playback.  
To pause playback.  
Title number (Track number)  
:
Chapter number  
:
To stop playback.  
Elapsed time of the current title or track  
:
Playback starts from the beginning of the current  
chapter or track.  
Remaining time of the current title or track  
When you press twice in quick successions, playback  
starts from the beginning of the preceding chapter or  
track.  
:
To locate succeeding chapters or tracks.  
Viewing the operational status  
1. Press DISPLAY.  
The following display appears.  
Time counter  
Elapsed time / remaining time of the current track  
Elapsed time / remaining time of the current title  
Time  
“PBC On” will  
be displayed  
when PBC is  
on.  
Time  
00:01:12 / 01:52:46  
Title number  
Chapter number  
3. To turn off the display, press DISPLAY  
again.  
2. Press DISPLAY again.  
Bit rate (Mbit/s)  
Audio setting  
Angle setting  
D 2 Ch Eng  
Amount of picture, sound and subtitle data  
in the DVD transferred per second.  
The larger the value is, the more data  
processed, but this does not necessarily  
insure better picture quality.  
Subtitle setting  
Bit rate  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced playback  
Playing MP3 Files  
You can play MP3 files that have been recorded on a CD-R or CD-RW on the DVD player.  
Playing MP3 files  
Play modes for MP3/CD/DivX®  
Preparations  
When you play MP3/CD/DivX®, you are able to modify the Play  
modes through the Toolkit which appears on the right of below  
Make sure that a disc you want to play is compatible  
with this DVD player.  
picture on the screen. Press  
/
buttons to navigate between  
the windows and buttons to select files/tracks or play mode  
/
Place a CD that contains MP3 files on  
the disc tray.  
items.Then press ENTER button. Please refer to below steps to  
playback files/tracks in the Program view list:  
1. Select Edit mode in the Toolkit then press ENTER button to  
start edit mode.  
1
2
Press OPEN/CLOSE to load the disc.  
2. Select a file/track or more files/tracks you want in the original  
A list of folders/files will appear on the screen.  
view list with the ENTER button.  
3. Select Add to program in theToolkit then press ENTER.“  
Press  
/
to select the desired folder or  
track/file, then press ENTER.  
If a track/file is selected, playback will start.  
If a folder is selected, the files in the folder  
will appear.  
will disappear from the screen. It means that the files/tracks  
you have selected already added into the program view list.  
4. Select Program view in the  
Toolkit then press ENTER to  
T01_Divx1.5Mbp.MP3  
1/3  
open the files/tracks in the  
Program view list that you  
already selected in step 2.  
5. Press PLAY to playback all  
files/tracks in the Program  
view list.  
T01_Divx1.5Mbp  
Repeat  
Mode  
:
:
Off  
To stop playback, press STOP.  
T02_Divx3Mbps  
T03_Divx4Mbps  
Normal  
3
JPEG Preview  
The Toolkit has the following play mode items:  
Filter (Audio/Photo/Video): Sets file filters.  
Filter is not applicable to Audio CD.  
Repeat (Off/Track/All):  
Off: Resumes normal playback.  
Track: Repeats the current track/file.  
All: Repeats all files on the current folder or all tracks on the disc.  
Mode (Normal/Shuffle/Music Intro):  
Normal: Resumes normal playback.  
Selecting a specific time of the current track  
1. Press T.  
2. Enter the time to select a specific time you want to play.  
3. Press ENTER to begin playback of the selected time.  
Notes  
• Letters of a file/folder name overflowing the given space are not  
displayed.  
Shuffle: Playbacks track/file in random order.  
You can play in fast reverse or fast forward during MP3 playback.  
Music Intro: Only playbacks the first 10 seconds of all the  
files on the current folder or all tracks on the disc.  
Edit mode: Memory operation works only when Edit mode is  
selected. After finish storing the files/tracks you want into  
the Program view list, select “Edit mode” again and press  
ENTER to release edit mode.  
Program view:To view tracks/files in the Program view list.  
It is disabled when the Program view list is empty.  
Add to program: Add files/tracks to the Program view list. It  
is disabled if the Edit mode is not selected. (The maximum  
number of files/tracks can be added is 30.)  
Browser view:To view files/tracks in the original view list.  
Clear program: Delete the files/tracks in the Program view  
list. Select a file/track or more you want to delete in stop  
mode. “ “ will appear besides the deleted file/track. Select  
Clear program and then press ENTER. It is disabled if the  
Edit mode is not selected.  
To pause playback  
Press PAUSE/STEP during playback.  
To resume normal playback, press  
the PLAY button.  
Notes  
• Some discs may not permit this operation.  
• The COAXIAL DIGITAL AUDIO OUT jack outputs MP3 sounds  
in the linear PCM format regardless of the current “Digital Output”  
selection.  
• The SKIP function is also available.  
Playable files  
MP3 disc compatibility with this player is limited as follows:  
• Playable discs:  
CD-R (650MB / 74 min. only)  
CD-RW may not be compatible.  
44.1 kHz only  
This DVD player requires discs/recordings to meet certain technical  
standards in order to achieve optimal playback quality. Pre-  
recorded DVDs are automatically set to these standards. There  
are many different types of recordable disc formats (including  
CD-R containing MP3 files). Because this area of technology is  
still evolving, Toshiba cannot guarantee that all recordable discs  
will produce optimal playback quality. The technical criteria set  
forth in this owner’s manual are meant only as a guide.  
• Sampling Frequency:  
• Bit rate:  
• CD physical format:  
• File system:  
32 kbps - 320 kbps (CBR*)  
Mode 1, Mode 2 XA Form 1  
ISO9660 Level 1, 2 or Joliet  
A file name should be in alphabet and  
numerals only, and must incorporate  
“MP3” extension. e.g. “********.MP3”.  
• File name:  
Total number of folders: Less than 256  
Total number of files:  
* CBR = Constant Bit Rate  
Please be advised that you must obtain permission from the  
applicable copyright owners to download copyrighted content,  
including music files, in any format, including the MP3 formats,  
prior to the downloading thereof.Toshiba has no right to grant and  
does not grant permission to download any copyrighted content.  
Less than 1000  
Note: When the MP3 file is out of the above specifications, the  
song may be skipped or muted with counter moving.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing JPEG Files  
You can play JPEG files that have been recorded on a CD-R or CD-RW on the DVD player.You can select a preferred view:a  
page of 9 thumbnail images or a single image view. Also, rotating, enlarging and shifting of each image can be possible.  
33  
To playback in HD JPEG resolution, see  
.
Viewing JPEG files  
Preparations  
Prepare a disc that contains JPEG files you want to view (see next page for Jpeg files compatibility). In Setup  
32  
Menu, it is preferred to select “Original” for “View Mode”  
.
Make your TV shape conform to the 4:3 picture size. Only 4:3 pictures can be played regardless of the function  
settings via the on-screen displays of the DVD player. If the TV is adjusted to other sizes, e.g. “16:9”, images will  
appear to be horizontally expanded. For details, refer to the owner’s manual of your TV.  
Press the  
/
/
/
buttons to view a different part of the  
Press OPEN/CLOSE to open the disc tray,  
place a disc that contains JPEG files.  
image.You may move the image from the centre position to  
UP, DOWN, LEFT and RIGHT direction.When you reach the  
edge of the image, the display will not shift anymore in that  
direction.  
1
Press OPEN/CLOSE to close the disc  
tray. A list of folders/files will appear on  
the screen.  
To resume normal playback  
1/  
3
A list of files in the  
Press the ZOOM repeatedly until the  
Off is displayed.  
disc  
appears.  
Original picture is restored when the  
appears.  
Depending on the file size, some files may  
not display the entire image.  
Off  
Repeat  
Mode  
:
:
Off  
ZOOM  
(Selection mode)  
e.g.  
Normal  
To rotate an image  
W: 515 H:770  
During playback, press the  
the picture on the TV screen.  
/
button repeatedly to rotate  
Press  
/
button to select your  
desired file, and then press ENTER or  
PLAY button to start slide show  
: rotate the picture anti-clockwise by 90o  
: rotate the picture clockwise by 90o.  
34  
playback  
.
To set transition effect  
Press STOP to display a folder list.  
During playback, press the ANGLE button to select the  
transition effect: Wipe down transition, Wipe up transition,  
... , No transition.  
Note: When you press button to  
/
select the left file, the selected picture  
will appear at the lower right corner.  
Note  
The transition effect only works in 480p/576p video  
resolution if the HD JPEG Mode is set to “On”.  
To quit the JPEG playback, press STOP.  
• Pressing the OPEN/CLOSE button to open  
the disc tray can also quit the playback.  
Viewing a thumbnail view  
To pause playback  
Press PAUSE/STEP during playback  
To resume normal playback, press  
Press TOP MENU in full-screen review.  
1
e.g.  
PLAY.  
To change the image  
To view the succeeding image, press SKIP  
.
To view the previous image, press SKIP  
.
Press the  
/
/
/
to select an  
image, press PLAY to view one  
image in full-screen and  
automatically images will be  
displayed one by one again in a few  
seconds.  
To magnify image  
Press ZOOM repeatedly.  
ZOOM  
Each time you press the ZOOM button, the  
magnification level changes as follows:  
Turn the page if necessary  
Press SKIP to view other thumbnail screen.  
/
1
2
3
Off  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced playback  
JPEG files compatibility  
Discs whose compatibility with this DVD player has been confirmed by TOSHIBA are as follows.  
CANON QuickCD  
Kodak Picture CD  
FUJICOLOR CD  
NORITSU QSS CD  
JPEG disc compatibility with this DVD player is limited as follows:  
• Playable discs:  
CD-R (650MB / 74 min. only)  
CD-RW may not be compatible.  
• CD physical format:  
• File system:  
Mode 1, Mode 2 XA Form 1  
ISO9660 Level 1, 2 or Joliet  
• File name:  
A file name should be in alphabet and numerals only, and must incorporate “JPG”  
extension.  
e.g.“********.JPG” (Do not name the file with “JPE” or “JPEG” extension.)  
Total number of folders:  
Total number of files:  
Less than 256  
Less than 1000  
Depending on the file size, some files may not display the entire image.  
Some discs may not permit this operation. Especially, the following conditions of included files will increase the disc’s  
inability.  
1. Pixels over 2880 x 1920 in height and/or width  
2. File size over 2M bytes  
3. File format except Exif  
Playing DivX®/MPEG-4 Files  
You can play DivX® and MPEG-4 files that have been recorded on a CD-R or CD-RW on the DVD player.  
Playing DivX®/MPEG-4 files  
Playable files  
Press OPEN/CLOSE to open the disc  
DivX® / MPEG-4 disc compatibility with this player is limited as  
follows:  
tray, place a disc that contains DivX® or  
MPEG-4 files.  
1
• Playable discs:  
CD-R (650MB / 74 min. only)  
CD-RW may not be compatible.  
DivX® 3.11, 4.12, 5.0, 5.1  
Press OPEN/CLOSE to close  
the disc tray, after completion of  
reading, a list of folders in the  
disc will appear.  
• DivX® versions:  
• Audio format:  
CBR MP3, VBR MP3, Mono MP3,  
DivX® AC3  
• Enhance video:  
• Frame rate:  
• CD physical format:  
• File system:  
GMC, Qpel, Progressive B-frames  
8 to 25 fps  
1/3  
I
Mode 1, Mode 2 X A Form 1  
ISO9660 Level 1, 2 or Joliet  
A file name should be in alphabet and  
numerals only, and must incorporate  
“DIVX” or “AVI” extension.  
A list of folders in the disc  
appears.  
Repeat  
Mode  
:
:
Off  
Normal  
• File name:  
e.g.  
e.g. “ *******.DIVX ”, “ *******.AVI ”  
Total number of folders: Less than 256  
Total number of files:  
Less than 1000  
Press  
/
to select your desired  
file, and then press ENTER or  
PLAY button to start playback.  
If your DivX® files include the  
subtitle file supported by this unit  
(see 31 ), the “External Subtitle  
File Selection” menu will appear,  
Notes  
• It is recommended to record the same kind of files in a CD-R or  
CD-RW.  
• Some DivX® Video-On-Demand files may require registration  
code of your DVD player, you may get the code in Misc  
settings  
.
use  
/
to select one extension  
36  
and then press ENTER to start  
playback.  
DivX, DivX Certified, and associated logos are trademarks  
of DivX, Inc. and are used under license.  
Press STOP to display a folder  
list.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playing USB Device  
You can connect the USB flash drives (not included) to the USB jack on the front of DVD player.  
You can play the files in MP3, DivX® or JPEG format stored on a USB flash drive by connecting it to this player.  
Connecting to USB flash drive  
To pause playback  
Press PAUSE/STEP during playback  
Plug the USB flash drive to the USB  
jack on the front of DVD player.  
1
To resume normal playback, press  
PLAY.  
Press the USB button on the remote  
control to select USB mode during DVD  
stop.  
2
To stop playback  
Pressing the OPEN/CLOSE button to open  
the disc tray can also quit the playback.  
USB  
1 /16  
01  
01.MP3  
Repeat : Off  
02  
03  
04  
05  
A list of folders/files  
will appear on the  
screen.  
Mode : Normal  
To return to DVD mode  
Pressing the DVD button on the remote  
DVD  
JPEG Preview  
control to resume DVD playback during  
USB device stop.  
06  
e.g.  
Press  
/
button to select your  
desired file, and then press ENTER  
or PLAY button to start playback.  
Notes  
• It is recommended to plug the USB flash drive when the DVD player is off.  
• It does not support USB harddisk mass storage device, multi-card reader and other USB computer peripheral.  
• It only supports FAT format (e.g. It does not support NTFS).  
• It only supports USB flash drive (max. 4G bytes).  
• The unit can recognise up to 127 folders and 999 files only.  
• It is not possible to play back files whose file size exceeds 1G bytes.  
• The connection may not be available depending on the type of your USB flash drive.  
• Do not disconnect the USB flash drive when you are playing it, it may corrupt the data. You may remove it in stop  
mode or DVD mode.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function setup  
Customizing the Function Settings  
You can change the default settings to customize performance to your preference.  
Setting procedure  
Setting details  
Press SETUP during stop.  
Language  
: English  
: Off  
1
2
Language  
The following on-screen display  
appears.  
DivX subtitle  
DVD Menu  
: ASCII  
: English  
: English  
Language  
: English  
: Off  
DivX subtitle  
DVD Menu  
: ASCII  
: English  
: English  
Language  
English:  
To view on-screen displays in English.  
Français: To view on-screen displays in French.  
Press  
/
to select an option for the  
:
:
To view on-screen displays in Arabic.  
To view on-screen displays in Persian.  
To view on-screen displays in Russian.  
setting you want to change, then press  
.
Ðóññêèé:  
Language settings  
Video settings  
Audio settings  
Rating settings  
Misc settings  
Indonesia: To view on-screen displays in Indonesian.  
1) Press SETUP button.  
2) Press button to select Language.  
3) Press ENTER button, then use the  
select a preferred language.  
4) Press ENTER button.  
/
button to  
5) Press SETUP button to exit the menu.  
Press  
/
to select the setting you want  
3
4
to change, then press ENTER.  
Language  
DivX subtitle  
Ðóññêèé  
DVD Menu  
Change the selection by  
/
buttons, by  
referring to the corresponding pages, then  
press ENTER.  
DVD  
Subtitle  
To select a preferred language (English, French,  
Arabic, Persian, Russian or Indonesian) for subtitles.  
Repeat steps 3 and 4 to change other  
settings.  
To select another option, press button to go back to  
step 2.  
Auto: To display subtitles in different languages other  
than you selected.  
Off: To disable subtitles.  
5
1) Press SETUP button.  
2) Press  
Subtitle.  
3) Press ENTER button, then use the  
a preferred language.  
button then use the  
/
button to select  
button to select  
Press SETUP.  
6
/
The on-screen display disappears.  
4) Press ENTER button.  
5) Press SETUP button to exit the menu.  
Note  
To quit the procedure, press the SETUP button to turn off  
the on-screen display.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD  
Audio  
Language  
Indonesian  
To select a preferred language (English, French, Arabic,  
Persian, Russian or Indonesian) for the sound track.  
DivX subtitle  
DVD Menu  
1) Press SETUP button.  
2) Press  
button, then use the  
/
button to select  
button to select  
Audio.  
3) Press ENTER button, then use the  
/
a preferred language.  
4) Press ENTER button.  
5) Press SETUP button to exit the menu.  
Notes  
• Some DVDs may be set to display subtitles in a different  
language other than you selected. A prior subtitle language  
may be programmed on the disc.  
Language  
• Some DVDs allow you to change subtitle selections only  
via the disc menu. If this is the case, press the MENU  
button and choose the appropriate subtitle language from  
the selection on the disc menu.  
: Off  
DivX subtitle  
ko18_r  
French  
DVD Menu  
Arabic  
Persian  
Russian  
DivX® Subtitle  
If your DivX® files include a subtitle file, then you may  
select a supported DivX® subtitle language by region:  
Note  
Some DVDs may not be played in a different language than  
you selected. A prior language may be programmed on the  
disc.  
ASCII  
Greek  
Unicode  
Turkish  
Hebrew  
Arabic  
Central European  
Cyrillic  
KO18_R  
1) Press SETUP button.  
2) Press button, then use the  
DivX subtitle.  
DVD  
DVD Menu  
/
button to select  
button to  
To select a preferred language (English, French, Arabic,  
Persian, Russian or Indonesian) for DVD menu.  
1) Press SETUP button.  
3) Press ENTER button, then use the  
/
select a preferred DivX® subtitle language.  
4) Press ENTER button.  
2) Press button, then use the  
/
button to select DVD  
5) Press SETUP button to exit the menu.  
Menu.  
3) Press ENTER button, then use the  
a preferred language.  
/
button to select  
Language  
4) Press ENTER button.  
: Off  
5) Press SETUP button to exit the menu.  
ASCII  
DivX subtitle  
DVD Menu  
Unicode  
Turkish  
Central European  
Cyrillic  
Language  
: Off  
DivX subtitle  
DVD Menu  
French  
Arabic  
Notes  
Persian  
Russian  
KOI8_R is an 8-bit character encoding, designed to cover  
Russian, which uses the Cyrillic alphabet. It also happens  
to cover Bulgarian.  
If your DivX® files do not include the subtitle file, you  
cannot use this selection.  
Note  
Some DVDs may not include your pre-selected language.  
In this case, the DVD player automatically displays disc  
menus consistent with the disc’s initial language setting.  
Supported subtitle file formats:  
.srt, .sub, .txt, .smi, .ssa.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function setup  
Customizing the Function Settings (continued)  
Setting details  
DVD  
View Mode  
: 16 : 9  
Aspect Ratio  
: Auto Fit  
Video  
The user may select one of the following options:  
Fill: Fill the screen with decoded image.  
Original: Display image as it original size. “Original” is  
preferred for Jpeg viewing.  
Height Fit: Fit the screen height with image height.  
Width Fit: Fit the screen width with image width.  
Auto Fit: Automatically fit the decoded image on screen  
without distortion.  
TV System  
Video Out  
: PAL  
: HDMI  
HDMI Resolution : Auto  
HD JPEG Mode : On  
JPEG Interval  
: 5 seconds  
Pan Scan: Automatically display decoded image on full  
screen without distortion.  
DVD  
Aspect Ratio  
1) Press SETUP button.  
2) Press  
3) Press  
/
button to select Video.  
1) Press SETUP button.  
button, then use the  
/
button to select  
button to the  
2) Press  
3) Press  
/
button to select Video.  
button, then use the  
View Mode.  
4) Press ENTER button, then use the  
options (Fill, Original, Height Fit, Width Fit, Auto Fit or  
Pan Scan).  
/
button to select  
/ button to shift  
/
Aspect Ratio.  
4) Press ENTER button, then use the  
and change the TV type.  
5) Press ENTER button.  
5) Press ENTER button.  
6) Press SETUP button to exit the menu.  
6) Press SETUP button to exit the menu.  
Aspect Ratio  
Aspect Ratio  
: 16 : 9  
TV System  
Video Out  
TV System  
: HDMI  
Height Fit  
Video Out  
HDMI Resolution : Auto  
HD JPEG Mode : On  
Width Fit  
HDMI Resolution  
HD JPEG Mode  
JPEG Interval  
: 5 seconds  
JPEG Interval  
: 5 seconds  
4:3  
Select when a standard 4:3 TV is  
connected.  
Displays pictures cropped to fill your TV  
screen. Either or both sides of the picture  
are cut off.  
Pan Scan  
Auto Fit  
Select when a standard 4:3 TV is  
connected. Displays pictures cropped  
to fill your TV screen. Either or both  
sides of the picture are cut off.  
16:9  
Select when a 16:9 TV is connected.  
Automatically fit the decoded image  
on screen without distortion. Black  
bars will be present on top/bottom or  
left/right of screen.  
Notes  
The displayable picture size is preset on the DVD.  
Therefore, the playback picture of some DVDs may not  
conform to the picture size you select.  
Note  
Depending on the DVDs, you may not be able to view  
the mode as selected.  
When you play DVDs recorded in the 4:3 picture size  
only, the playback picture always appears in the 4:3 picture  
size regardless of the TV shape setting. But, if Video  
Output is set to HDMI 720p/1080i/1080p, then picture  
will be 16:9 only.  
If you select “16:9” and you own a 4:3 TV set, the DVD  
playback picture will be horizontally distorted during  
playback. Images will appear to be horizontally  
compressed.Always be sure that yourTV shape conforms  
to the actual TV in use.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV System  
HDMI Resolution  
1) Press SETUP button.  
1) Press SETUP button.  
2) Press  
3) Press  
/
button to select Video.  
2) Press  
3) Press button, then use the  
TV System.  
4) Press ENTER button, then use the  
shift and change the TV system.  
5) Press ENTER button.  
/
button to select Video.  
button, then use the  
/
button to select  
/
button to select  
HDMI Resolution.  
4) Press ENTER button, then use the  
select the options (Auto, 480p/576p, 720p, 1080i or  
1080p).  
5) Press ENTER button.  
6) Press SETUP button to exit the menu.  
/
button to  
/
button to  
6) Press SETUP button to exit the menu.  
Aspect Ratio  
: 16 : 9  
Aspect Ratio  
: 16 : 9  
: Auto Fit  
NTSC  
PAL  
: Auto Fit  
TV System  
TV System  
Video Out  
: PAL  
Auto  
Video Out  
HDMI Resolution  
HD JPEG Mode  
Auto  
480p/576p  
HDMI Resolution  
HD JPEG Mode  
JPEG Interval  
720p  
1080i  
1080p  
JPEG Interval  
: 5 seconds  
Notes  
NTSC: Select if your TV system is NTSC.  
• If the Video Out is not set to “HDMI”, you cannot select  
the “HDMI Resolution”.  
• Select the HDMI resolution according to the performance  
of the connected TV.  
PAL: Select if your TV system is PAL.  
Auto: The DVD player automatically identifies PAL or  
NTSC video system of disc. Connect  
a
a
multisystem TV (PAL / NTSC compatible) to view  
a picture. A playback picture may be distorted  
when detected a signal change between PAL  
and NTSC on the disc. For the case of  
Progressive mode, your multisystem TV must be  
able to support 525p and 625p.  
HD JPEG Mode  
1) Press SETUP button.  
2) Press  
/
button to select Video.  
3) Press button, then use the  
JPEG Mode.  
4) Press ENTER button, then use the  
On or Off mode.  
5) Press ENTER button.  
6) Press SETUP button to exit the menu.  
/
button to select HD  
Video Out  
/
button to select  
1) Press SETUP button.  
2) Press  
3) Press  
/
button to select Video.  
button, then use the  
/
button to select  
button to select  
Video Out.  
4) Press ENTER button, then use the  
the output mode (Composite or HDMI).  
5) Press ENTER button.  
On: JPEG image is displayed in a suitable picture quality  
/
(480p/576p, 720p, 1080i or 1080p).  
Off: The picture quality is fixed to 480p/576p.  
6) Press SETUP button to exit the menu.  
Aspect Ratio  
: 16 : 9  
Aspect Ratio  
: 16 : 9  
: Auto Fit  
: PAL  
: Auto Fit  
TV System  
: PAL  
TV System  
Video Out  
Video Out  
: HDMI  
Composite  
HDMI Resolution  
HD JPEG Mode  
On  
Off  
HDMI Resolution  
HD JPEG Mode  
JPEG Interval  
HDMI  
JPEG Interval  
: 5 seconds  
Notes  
• If the Video Out is not set to “HDMI”, you cannot select  
the “HD JPEG Mode”.  
• All JPEG pictures will not be output through the VIDEO  
OUT jack when 720p, 1080i, 1080p or Auto is selected  
with HD JPEG Mode on.  
• For HDMI output, DISPLAY and ZOOM buttons only work  
in 480p/576p resolution mode when HD JPEG Mode is  
On.  
Composite: Select if you connect the DVD to your TV  
via composite video (yellow) input.  
HDMI:  
High Definition Multimedia Interface. Select if  
you connect the DVD to TV via HDMI input.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function setup  
Customizing the Function Settings (continued)  
Setting details  
PCM: Select when connected to a Multi-channel digital  
JPEG Interval  
stereo amplifier.The DVD player outputs sound in the PCM  
stereo format when you play a DVD recorded on the Dolby  
Digital, MPEG1 or MPEG2 recording system.  
Bitstream: Disc audio raw data will be output. Select  
“Bitstream” if your amplifier supports “DTS”.  
1) Press SETUP button.  
2) Press  
/
button to select the Video.  
3) Press button, then the  
Interval.  
4) Press ENTER button, then the  
change the JPEG Interval.  
5) Press ENTER button.  
/
button to select the JPEG  
Off:To disable Digital Output.  
/
button to shift and  
Off  
6) Press SETUP button to exit the menu.  
PCM  
Bitstream  
Aspect Ratio  
: 16 : 9  
: Auto Fit  
TV System  
: PAL  
: HDMI  
Off  
Video Out  
HDMI Resolution  
HD JPEG Mode  
JPEG Interval  
5 seconds  
Notes  
10 seconds  
15 seconds  
When you make a connection to a TV, Dolby Surround  
Pro Logic or stereo system via the analogue audio jacks,  
select “PCM” or “Bitstream”.  
If this DVD player is connected to a TV using HDMI,  
make sure to select “PCM”.  
Off:  
Plays back one file at a time.  
5 seconds: Plays back images in the form of a slide  
show at 5 seconds interval.  
10 seconds: Plays back images in the form of a slide  
show at 10 seconds interval.  
15 seconds: Plays back images in the form of a slide  
show at 15 seconds interval.  
Night Mode  
Night mode is equivalent to Dynamic Range Compress.  
When it is On, it reduces the variations between loud and  
soft sounds in audio output.You can still hear softer sounds  
and dialog even in very low volume.  
1) Press SETUP button.  
2) Press  
3) Press  
Night Mode.  
4) Press ENTER button, then use the  
select the On or Off mode.  
/
button to select Audio.  
: PCM  
Audio  
button, then use the  
/
button to select  
button to  
: Off  
/
5) Press ENTER button.  
6) Press SETUP button to exit the menu.  
: PCM  
Off  
On  
Digital Output  
Selects the output sound format corresponding to your  
system connection.  
1) Press SETUP button.  
2) Press  
3) Press  
Digital Output.  
4) Press ENTER button, then use the  
the output sound format.  
5) Press ENTER button.  
/
button to select Audio.  
Note  
button, then use the  
/
button to select  
button to select  
Night mode is Dynamic Range Control (DRC) option for  
analogue audio output.  
/
6) Press SETUP button to exit the menu.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD  
Set Password  
Parental Control  
Set Password  
:
8. Adult  
Rating  
New Password can be set to replace the default password.  
1) Press SETUP button.  
2) Press  
/
button to select Rating.  
3) Press button, then use the  
/
button to select Set  
Password.  
4) Press ENTER button. “Enter Password” screen will  
appear.  
5) Press the number buttons to input the current  
password (If the password has not been set yet after  
you purchase this unit, it is “8888”). Then press  
ENTER.  
6) Press ENTER button again,New Passwordscreen will  
appear. Press the number buttons to input the new  
password.  
7) Press ENTER button, “Confirm Password” screen will  
appear.Enter the same password again for confirmation.  
8) Press ENTER button. Now your new password has been  
set. Be sure to remember this number!  
DVD  
Parental Control  
DVDs equipped with the password function are rated  
according to their content.The contents allowed by a parental  
lock level and the way a DVD can be controlled may vary  
from disc to disc.  
For example, if the disc allowed, you could edit out violent  
scenes unsuitable for children and replace them with more  
suitable scenes, or you could lock out playback of the disc  
altogether.  
If you forget the password, you can erase your  
current password by pressing number button 8  
on the remote control four times, then press  
ENTER button to confirm the setting.  
DVDs may or may not respond to the parental lock  
settings. This is not a defect in the DVD player. Make  
sure this function works with your DVDs.  
PASSWORD:8888  
1) Press SETUP button.  
2) Press  
3) Press  
/
to select Rating.  
button to  
Misc  
select Parental  
Control, then press  
ENTER button.  
“Enter Password”  
screen will appear.  
Parental Control  
Set Password  
Enter Password:  
:
8. Adult  
Screen saver  
HDMI CEC  
:
:
On  
Off  
4) Press “8888” using  
number buttons.  
(Please note, this is  
presetting password of this unit).Then press ENTER.  
Press ENTER again to list the parental level.  
Use Default Settings  
The parental lock level is equivalent to the following  
ratings:  
If you want to return the initial language setting such as  
Language, Video, Audio and etc. to the factory default, do  
the following:  
Level 1: Kid Safe  
Level 2: G  
Level 3: PG  
Level 5: PG-R  
Level 6: R  
Level 7: NC-17  
Level 8: Adult  
1) Press SETUP button.  
Level 4: PG-13  
2) Press  
/
button to select Misc.  
5) Press  
/
to select the rating from 1 to 8. Rating one  
3) Press button to select Use Default Settings, then  
press ENTER button.  
(1) has the most restrictions while rating eight (8) can  
virtually playback all DVD software.  
6) Press OPEN/CLOSE button to activate the Parental Level  
setting.  
4) Press  
/
button to select “Yes”, then press ENTER  
button.The original setting will be restored.  
If the DVD has been designed to temporarily cancel the  
Parental Level, the screen will change depending on which  
disc is played. If you select “YES” with the ENTER  
button, “Enter Passwordscreen will appear.Input the 4-  
digit password as you have set then followed by ENTER  
button and playback will start. If “NO” is selected, press  
the OPEN/CLOSE to remove the disc.  
Screen saver  
:
On  
Do you want to use default setting?  
Notes  
• If you input a wrong password, press CLEAR button  
and re-enter your 4-digit password again.  
You cannot play DVDs rated higher than the level you  
selected unless you cancel the parental lock function.  
Note  
When you reset the DVD player to the factory default, the  
DVD player will take 3-5 seconds to reset.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function setup  
Customizing the Function Settings (continued)  
Setting details  
DivX® Registration  
HDMI CEC  
Some DivX® Video-On-Demand files required registration  
code, please get the code of your DVD player as follow:  
You can control this DVD unit from TV’s remote which is  
connected via HDMI cable.  
1) Press SETUP button.  
1) Press SETUP button.  
2) Press  
3) Press  
/
button to select Misc.  
button, then use the  
/
button to select  
2) Press  
/
button to select Misc.  
DivX Registration.  
4) Press ENTER button, your registration code will be  
shown.  
5) Press ENTER button.  
6) Press SETUP button to exit the menu.  
3) Press button, then use the  
HDMI CEC.  
4) Press ENTER button, then use the  
select the On or Off mode.  
5) Press ENTER button.  
/
button to select  
button to  
/
6) Press SETUP button to exit the menu.  
Screen saver  
DivX Video On Demand  
:
On  
R
Screen saver  
HDMI CEC  
:
On  
Your registration code is  
:
Off  
On  
Note  
This registration code is for DivX® Video-On-Demand only.  
Do not apply this code for other applications or websites.  
Off: To deactivate HDMI-CEC.  
On: To activate HDMI-CEC.  
Functions available for the HDMI-CEC  
One touch play  
Screen Saver  
When the operations with following buttons of this  
unit’s remote control are performed, the TV will  
automatically switch to appropriate input channel.  
To turn on or off the screen saver (screen protection  
to prevent image burn).  
Button for one touch play: [PLAY] (make sure a  
disc is inserted.)  
1) Press SETUP button.  
2) Press  
/
button to select Misc.  
3) Press button, then use the  
Screen saver.  
4) Press ENTER button, then use the  
select the On or Off mode.  
5) Press ENTER button.  
/
button to select  
button to  
System information  
Get & Set Menu Language:  
/
This unit recognizes the OSD languages set for  
the TV and automatically set the same language  
as the player menu language (OSD menu  
language) for this unit.  
6) Press SETUP button to exit the menu.  
Power off:  
When you turn the TV off, this unit will automatically  
turn off.  
Off  
On  
Screen saver  
HDMI CEC  
Receiving operational signal fromTV’s Remote:  
You can operate this unit with TV’s remote control.  
Check your TV owner’s manual for details.  
Notes  
This function may not work properly depending on  
the TV you are connecting.  
If the Video Out is not set to “HDMI”, HDMI-CEC  
will not work.  
Other components must be compatible with HDMI-CEC  
in order to use this function.  
Note  
When you leave the unit in DVD stop mode for approximately  
2 minutes, the screen saver of the DVD player automatically  
appears if you set the Screen saver to On mode.To turn off  
the screen saver, press the PLAY button.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Languages  
Table of languages and their abbreviations  
Abbreviation  
Language  
Abbreviation  
Language  
Abbreviation  
Language  
– – –  
No alternate  
language  
Chinese  
Dutch  
English  
French  
German  
Italian  
Japanese  
Korean  
GN  
GU  
HA  
HI  
HR  
HU  
HY  
IA  
IE  
IK  
IN  
IS  
Guarani  
Gujarati  
Hausa  
Hindi  
Croatian  
Hungarian  
Armenian  
Interlingua  
Interlingue  
Inupiak  
Indonesian  
Icelandic  
Hebrew  
PT  
QU  
RM  
RN  
RO  
RU  
RW  
SA  
SD  
SG  
SH  
SI  
Portuguese  
Quechua  
Rhaeto-Romance  
Kirundi  
Rumanian  
Russian  
Kinyarwanda  
Sanskrit  
Sindhi  
CHI (ZH)  
DUT (NL)  
ENG (EN)  
FRE (FR)  
GER (DE)  
ITA (IT)  
JPN (JA)  
KOR (KO)  
MAY (MS)  
SPA (ES)  
AA  
AB  
AF  
AM  
AR  
AS  
AY  
AZ  
BA  
BE  
BG  
BH  
BI  
BN  
BO  
BR  
CA  
CO  
CS  
CY  
DA  
DZ  
EL  
EO  
ET  
Sango  
Malay  
Spanish  
Afar  
Serbo-Croatian  
Singhalese  
Slovak  
Slovenian  
Samoan  
Shona  
IW  
JI  
SK  
SL  
Abkhazian  
Afrikaans  
Amharic  
Arabic  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Belorussian  
Bulgarian  
Bihari  
Bislama  
Bengali, Bangla  
Tibetan  
Breton  
Catalan  
Corsican  
Czech  
Welsh  
Danish  
Bhutani  
Greek  
Esperanto  
Estonian  
Basque  
Persian  
Finnish  
Fiji  
Faroese  
Frisian  
Yiddish  
JW  
KA  
KK  
KL  
KM  
KN  
KS  
KU  
KY  
LA  
LN  
LO  
LT  
Javanese  
Georgian  
Kazakh  
Greenlandic  
Cambodian  
Kannada  
Kashmiri  
Kurdish  
Kirghiz  
Latin  
Lingala  
Laotian  
Lithuanian  
Latvian, Lettish  
Malagasy  
Maori  
Macedonian  
Malayalam  
Mongolian  
Moldavian  
Marathi  
Maltese  
Burmese  
Nauru  
Nepali  
Norwegian  
Occitan  
SM  
SN  
SO  
SQ  
SR  
SS  
ST  
SU  
SV  
SW  
TA  
TE  
TG  
TH  
TI  
TK  
TL  
TN  
TO  
TR  
TS  
TT  
TW  
UK  
UR  
UZ  
VI  
VO  
WO  
XH  
YO  
ZU  
Somali  
Albanian  
Serbian  
Siswati  
Sesotho  
Sundanese  
Swedish  
Swahili  
Tamil  
Telugu  
Tajik  
Thai  
Tigrinya  
Turkmen  
Tagalog  
Setswana  
Tongan  
Turkish  
Tsonga  
Tatar  
LV  
MG  
MI  
MK  
ML  
MN  
MO  
MR  
MT  
MY  
NA  
NE  
NO  
OC  
OM  
OR  
PA  
PL  
PS  
Twi  
Ukrainian  
Urdu  
EU  
FA  
FI  
FJ  
FO  
FY  
GA  
GD  
Uzbek  
Vietnamese  
Volapük  
Wolof  
Xhosa  
Yoruba  
(Afan) Oromo  
Oriya  
Panjabi  
Polish  
Pashto, Pushto  
Irish  
Scottish Gaelic  
Galician  
GL  
Zulu  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Others  
Before Calling Service Personnel  
Check the following guide for the possible cause of a problem before contacting service.  
Symptoms and correction  
Symptom  
Cause  
Correction  
Page  
Nopower.  
• The power plug is disconnected.  
• Connect the power plug securely into the  
wall outlet.  
11-12  
The DVD player turned off by  
itself.  
• The automatic power off function turned the  
unit off.  
• Press the PLAY button.  
16  
16  
No picture  
Nosound.  
• The TV is not set to receive DVD signal  
output.  
• Select the appropriate video input mode on  
theTV so the picture from the DVD player  
appears on theTV screen.  
• The video/HDMI cable is not connected  
securely.  
• Connect the video/HDMI cable securely into  
the appropriate jacks.  
11-12  
• Mismatch setting between TV and this unit.  
• Wrong connection.  
• Select the correctVideo Output setting.  
• Check the connection.  
33  
11-12  
16  
• The equipment connected with the audio cable is  
not set to receive DVD signal output.  
• Select the correct input mode of the audio  
receiver so you can listen to the sound from  
the DVD player.  
• The audio cable is not connected securely.  
• The audio receiver or TV is turned off.  
• Connect the audio cable securely into the  
appropriate jacks.  
11-15  
16  
Turn on the equipment connected with the  
audio cable.  
• The setting of output sound format is  
incorrect.  
• Select the proper audio setting.  
34  
The playback picture has  
occasional distortion.  
• The disc is dirty.  
• Remove the disc and clean it.  
5
-
• It is in fast forward or fast reverse playback.  
• Sometimes a small amount of picture  
distortion may appear.This is not a  
malfunction.  
Brightness is unstable or noises  
are present in the playback  
pictures.  
• The effect of copy protection.  
• Connect the DVD player directly to theTV.  
Avoid connecting the DVD player to aVCR or  
TV/VCRcombination.  
11  
The DVD player does not start  
playback.  
• No disc is inserted.  
• Insert a disc.  
16  
6
• An unplayable disc is inserted.  
• Insert a playable disc. (Check the disc type  
and colour system.)  
• The disc is placed upside down.  
• Place the disc with the playback side down.  
16  
16  
• The disc is not placed within the guide.  
• Place the disc correctly inside the guide on  
the disc tray.  
• The disc is dirty.  
• Clean the disc.  
5
• The parental lock function is set.  
• Cancel the parental lock function or change  
the parental lock level.  
35  
Playback does not follow the  
course of the disc’s program.  
• It is in the mode of repeat playback, memory  
playback, etc.  
• These operations may prevent a proper  
progress of the contents.  
-
-
Buttons do not work.  
• Power supply fluctuations or other  
abnormalities such as static electricity may  
interrupt correct operations.  
• Press and hold the ON/STANDBY button on  
the front panel for more than about 3  
seconds.The DVD player turns off.Press the  
button again to turn it on. If the buttons still do  
not work, disconnect the power plug and insert  
it into the wall outlet again.  
The remote control does not work • The remote control is not pointed at the  
properly.  
remote sensor of the DVD player.  
• Point the remote control at the remote sensor of  
the DVD player.  
10  
• The remote control is too far from the DVD player. • Operate the remote control within about 7 m.  
10  
10  
• The batteries in the remote control are  
exhausted.  
• Replace the batteries with new ones.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
DVD player / outputs / supplied accessories  
DVD Player  
Power supply  
Power consumption  
Mass  
100V - 240V AC, 50/60Hz  
11 W (standby: less than 1.0W)  
1.26 kg  
External dimensions  
Signal system  
Laser  
430 x 41 x 197 mm (W/H/D)  
PAL/3.58 NTSC  
Semiconductor laser, wavelength 650/780 nm  
Frequency range  
DVD linear sound : 48 kHz sampling 4 Hz to 22 kHz  
96 kHz sampling 4 Hz to 44 kHz  
Signal-to-noise ratio  
Audio dynamic range  
Harmonic distortion  
Wow and flutter  
More than 93 dB  
More than 80 dB  
Less than 0.05 %  
Below measurable level (less than ±0.001 % (W.PEAK))  
Temperature: 5 °C to 35 °C, Operation status: Horizontal  
Operating conditions  
Outputs  
Video output  
1.0 V (p-p), 75 , negative sync., pin jack x 1  
0.5V (p-p), 75 , pin jack x 1  
2.0 V (rms), 680 , pin jacks (L, R) x 1  
19 pin  
Audio output (COAXIAL DIGITAL)  
Audio output (ANALOG)  
HDMI output  
Supplied Accessories  
Audio/Video cable................................................. 1  
Remote control (SE-R0350) ................................. 1  
Batteries (R03/AAA) ............................................. 2  
• This model complies with the above specifications.  
• Designs and specifications are subject to change without notice.  
• This model may not be compatible with features and/or specifications that may be added in the future.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
811-S90091W021  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Technicolor Thomson DVD Player DTH500B User Manual
Teledex Cordless Telephone CL1900 User Manual
Teledyne Respiratory Product TED 191 User Manual
Telex Headphones PH 44 User Manual
Toshiba Marine Radio A300 User Manual
Troy Bilt Lawn Mower ZT50 User Manual
UNICOM Electric Switch DynaGST 1602G User Manual
VocoPro Karaoke Machine DVG 909K User Manual
Wagner SprayTech Paint Sprayer 179070 User Manual
Waste King Garbage Disposal 1001 User Manual