Toshiba CRT Television 36A12 User Manual

Color Television  
36A12  
Owner’s Manual  
®
I
© 2002 TOSHIBA CORPORATION  
All Rights Reserved.  
23565683  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Instructions  
Installation, Care, and Service  
1) Read these instructions.  
2) Keep these instructions.  
3) Heed all warnings.  
Installation  
Follow these recommendations and precautions and heed all  
warnings when installing your TV:  
4) Follow all instructions.  
15) Never modify this equipment. Changes or modifications  
may void: a) the warranty, and b) the users authority to  
operate this equipment under the rules of the Federal  
Communications Commission.  
5) Do not use this apparatus near  
water.  
16)  
DANGER: RISK OF SERIOUS PERSONAL  
INJURY, DEATH, OR EQUIPMENT  
DAMAGE! Never place the TV on  
6) Clean only with a dry cloth.  
an unstable cart, stand, or table. The TV  
may fall, causing serious personal injury,  
death, or serious damage to the TV.  
7) Do not block any ventilation  
openings. Install in accordance with  
the manufacturers instructions.  
17) Never place or store the TV in direct  
sunlight; hot, humid areas; areas  
subject to excessive dust or vibration;  
or locations with temperatures at or  
below 41°F (5°C).  
8) Do not install near any heat  
sources such as radiators,  
heat registers, stoves, or other  
apparatus (including amplifiers)  
that produce heat.  
9) Do not defeat the safety purpose of the polarized or  
grounding type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug has  
18) Always place the TV on the floor  
or a sturdy, level, stable surface that  
can support the weight of the unit.  
two blades and a third grounding  
Wide plug  
prong. The wide blade or the third  
prong are provided for your safety.  
If the provided plug does not fit into  
your outlet, consult an electrician  
for replacement of the obsolete outlet.  
19) Never place items such as vases,  
aquariums, or candles on top of the TV.  
10) Protect the power cord from being  
walked on or pinched, particularly at  
plugs, convenience receptacles, and  
the point where it exits the apparatus.  
20) Never block or cover the slots or  
openings in the TV cabinet back,  
bottom, and sides. Never place  
the TV:  
11) Only use attachments/accessories specified by the  
manufacturer.  
on a bed, sofa, rug, or similar  
surface;  
too close to drapes, curtains,  
or walls; or  
in a confined space such as a  
bookcase, built-in cabinet, or any  
other place with poor ventilation.  
12) Use only with the cart, stand, tripod,  
bracket, or table specified by the  
manufacturer, or sold with the  
apparatus. When a cart is used, use  
caution when moving the cart/apparatus  
combination to avoid injury from tip-over.  
The slots and openings are provided  
to protect the TV from overheating  
and to help maintain reliable  
operation of the TV.  
13) Unplug this apparatus during  
lightning storms or when  
unused for long periods  
of time.  
21) Never allow anything to rest on or roll over the power  
cord, and never place the TV where the power cord is  
subject to wear or abuse.  
14) Refer all servicing to qualified service  
personnel. Servicing is required when  
the apparatus has been damaged in  
any way, such as power supply cord  
or plug is damaged, liquid has been  
22) Never overload wall outlets and  
extension cords.  
spilled or objects have fallen into the  
QUALIFIED  
apparatus, the apparatus has been exposed  
SERVICE  
TECHNICIAN  
to rain or moisture, does not operate normally,  
or has been dropped.  
FEB02  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
29) [This item applies to projection TVs only.] If the air  
temperature rises suddenly (for example, when the TV is  
first delivered), condensation may form on the lenses. This  
can make the picture appear distorted or the color appear  
faded. If this happens, turn off the TV for 6 to 7 hours to  
allow the condensation to evaporate.  
23) Always operate this equipment from  
a 120 VAC, 60 Hz power source only.  
30) For added protection of your TV from lightning and power  
surges, always unplug the power cord and disconnect the  
antenna from the TV if you leave the TV unattended or  
unused for long periods of time.  
24) Always make sure the antenna system is properly  
grounded to provide adequate protection against voltage  
surges and built-up static charges (see Section 810 of the  
National Electric Code).  
Antenna lead-in wire  
31) During normal use, the TV may make  
occasional snapping or popping  
Antenna discharge unit  
(NEC Section 810-20)  
Ground clamp  
sounds. This is normal, especially  
when the unit is being turned on or  
off. If these sounds become frequent  
or continuous, unplug the power cord  
and contact a Toshiba Authorized Service Center.  
Grounding conductors  
(NEC Section 810-21)  
Electric service equipment  
Power service grounding  
32) Possible Adverse Effects on TV Picture Tube: If a fixed  
(non-moving) pattern remains on the TV screen for long  
periods of time, the image can become permanently  
engrained in the picture tube and cause subtle but  
permanent ghost images. This type of damage is NOT  
COVERED BY YOUR WARRANTY. Never leave your TV  
on for long periods of time while it is displaying the  
following formats or images:  
electrode system (NEC Art 250 Part H)  
Ground clamps  
25)  
DANGER: RISK OF SERIOUS PERSONAL  
INJURY OR DEATH!  
Use extreme care to make sure you are never in  
a position where your body (or any item you are in contact  
with, such as a ladder or screwdriver) can accidentally  
touch overhead power lines. Never locate the antenna  
near overhead power lines or other electrical circuits.  
Never attempt to install any of the following during  
lightning activity:  
a) an antenna system; or b) cables, wires, or any home  
theater component connected to an antenna or phone  
system.  
Fixed Images, such as PIP/POP windows, stock tickers,  
video game patterns, TV station logos, and websites.  
Special Formats that do not use the entire screen. For  
example, viewing letterbox style (16:9) media on a  
normal (4:3) display (gray bars at top and bottom of  
screen); or viewing normal style (4:3) media on a  
widescreen (16:9) display (gray bars on left and right  
sides of screen).  
Care  
Service  
33)  
For better performance and safer operation of your TOSHIBA  
TV, follow these recommendations and precautions:  
WARNING: RISK OF ELECTRIC  
SHOCK! Never attempt to service the  
TV yourself. Opening and  
26) Always sit approximately 1025 feet away from the TV and  
as directly in front of it as possible. The picture can appear  
dull if you sit too far to the left or right of the TV, or if  
sunlight or room lights reflect on the screen. Turn the TV  
off to check for reflections on the screen, and then remove  
the source of reflections while viewing the TV.  
removing the covers may expose  
you to dangerous voltage or other  
hazards. Refer all servicing to a  
Toshiba Authorized Service Center.  
QUALIFIED  
SERVICE  
TECHNICIAN  
34) If you have the TV serviced:  
Ask the service technician to use only replacement parts  
specified by the manufacturer.  
Upon completion of service, ask  
the service technician to perform  
routine safety checks to determine  
that the TV is in safe operating  
condition.  
27) Always unplug the TV before  
cleaning. Never use liquid or  
aerosol cleaners.  
35) When the TV reaches the end of its useful life, ask a  
qualified service technician to properly dispose of the TV.  
Improper disposal may result in a picture tube implosion  
and possible personal injury.  
28)  
WARNING: RISK OF ELECTRIC SHOCK!  
Never spill liquids or push objects of any kind  
into the TV cabinet slots.  
FEB02  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Information ........................ 2-4  
Using the V-Chip Control (blocking) feature ...........20  
Selecting a PIN code ...........................................20  
Changing your PIN code ....................................21  
Blocking programs by ratings ..............................22  
Ratings definitions (MPAA, Youth TV, TV) ........22  
Unblocking programs temporarily ......................23  
Blocking unrated movies and programs...............23  
Blocking channels ...............................................24  
Locking video inputs ...............................................25  
Channel labels .........................................................26  
Video labels .............................................................27  
Watching picture-in-picture (PIP)............................28  
Switching the main and small pictures .....................28  
Changing the location of the PIP window................29  
Freezing the PIP display ...........................................29  
Watching multi-window PIP ...................................29  
Adjusting the picture ...............................................30  
Adjusting the picture quality ....................................30  
Selecting the color temperature ................................30  
Adjusting the picture preference...............................31  
Displaying on-screen information ............................31  
Setting the off timer .................................................31  
Auto power off .........................................................31  
Using the closed caption feature...............................32  
Adjusting the sound .................................................33  
Muting the sound ....................................................33  
Selecting stereo/SAP broadcasts ...............................33  
Adjusting the sound quality .....................................34  
Using the surround sound feature ............................34  
Selecting variable audio OUT ..................................35  
Turning off the built-in speakers ..............................35  
Using the sub-bass system (SBS) ..............................36  
Viewing the demonstration (DEMO) mode ............36  
Understanding the last mode memory feature ..........36  
Welcome to Toshiba ............................................ 6  
Exploring your new TV .............................................6  
Selecting a location for the TV ...................................6  
Connecting your TV ............................................. 7  
Note regarding picture quality .............................. 7  
Connecting a VCR ....................................................7  
Connecting a cable converter box ..............................8  
Connecting a cable converter box and VCR ...............8  
Connecting a DVD player or satellite receiver and a  
VCR ..........................................................................9  
Connecting a DVD player with ColorStream®  
(component video) and a VCR ................................10  
Connecting two VCRs .............................................10  
Connecting a camcorder ..........................................11  
Connecting an audio amplifier.................................11  
Using the remote control ................................. 12  
Preparing the remote control for use ........................12  
Installing the remote control batteries ......................12  
Using the remote control with a VCR or  
cable TV converter ...................................................12  
Programming the remote control for use with  
a non-Toshiba VCR or cable TV converter ..............13  
VCR code table...................................................13  
Cable TV converter code table ............................14  
Learning about the remote control ...........................15  
Setting up your TV ............................................. 16  
Changing the on-screen display language .................16  
Selecting the antenna input......................................16  
Selecting the signal source ........................................17  
Programming channels into the TV’s memory .........17  
Programming channels automatically ..................17  
Adding and erasing channels manually................18  
Changing channels...................................................18  
Appendix.............................................................. 37  
Troubleshooting .......................................................37  
Cleaning and care ....................................................38  
Specifications ...........................................................38  
Limited United States warranty................................39  
Limited Canada warranty ........................................40  
Using the TV’s features..................................... 19  
Adjusting the channel settings..................................19  
Switching between two channels ..............................19  
Programming your favorite channels ........................19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Welcome to Toshiba  
Congratulations! You have purchased one of the finest color TVs on the  
market. The goal of this manual is to guide you through setting up and  
operating your Toshiba TV as quickly as possible. You may need to  
purchase other audio or video cables to connect your equipment. See  
“Connecting your TV” on page 7 for more information.  
POWER  
LIGHT RECALL  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
2
5
8
0
3
6
1
4
CH  
Please read all safety and operating instructions carefully before you  
proceed.  
9
7
VOL  
CH RTN  
Exploring your new TV  
ENT  
100  
You can operate your TV using the buttons on the front panel or the  
remote control. The front and back panels provide terminal connec-  
tions for connecting other equipment to your TV.  
ADV/  
PIP CH  
MENU  
APT  
C
C.  
FAV  
ENTER  
FAV  
RESET  
EXIT  
ADV/  
PIP CH  
TV/Video  
Volume  
STOP SOURCE  
PLAY PIP  
Channel  
REC TV/VCR REW  
FF  
MENU  
TV / VIDEO  
VOLUME  
CHANNEL  
POWER  
STILL LOCATE SWAP  
VIDEO L/MONO  
AUDIO  
R
VIDEO-3 IN  
CT-9946  
POWER  
Video 3  
Remote Sensor  
Menu  
Power Indicator (Red)  
ANT (75)  
ANT-1  
OUT  
ANT-2  
IN  
OUT  
DVD IN  
COLOR  
S-VIDEO  
STREAM  
INPUT  
Y
VIDEO  
VIDEO  
Pb  
L/MONO  
L/MONO  
L
AUDIO  
R
AUDIO  
R
AUDIO  
R
Pr  
A
N
T
(
7
5
)
A
N
T
-
1
OUT  
A
N
T
-
2
IN  
OUT  
D
V
D
I
N
S-VIDEO  
VIDEO  
COLOR  
STREAM  
INPUT  
VIDEO 2  
VIDEO 1  
Y
VIDEO  
MONO  
L
/
L
Pb  
L/MONO  
AUDIO  
A
UDIO  
Pr  
AUDIO  
R
R
R
VIDEO  
2
VIDEO  
1
ColorStream  
(component video)  
Video 2  
Video 1  
Selecting a location for the TV  
• Place the TV on the floor or on the optional TV stand listed in the  
“Specifications” section.  
• Place the TV in a location where light does not directly hit the  
screen.  
• Place the TV far enough from the walls to allow proper ventilation.  
Inadequate ventilation may cause overheating, which may damage  
the TV.  
The model and serial numbers are on the back of your TV. Record the  
numbers in the space below. Refer to these numbers whenever you  
communicate with your Toshiba dealer about this TV.  
Model number: ________________________  
Serial number: ________________________  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Connecting your TV  
Note: Cables are not supplied with your TV.  
Coaxial cable is the cable that comes in from your antenna, cable TV service,  
or cable converter box. Coaxial cable uses Fconnectors.  
Coaxial (antenna) cable  
Standard stereo A/V cables usually come in sets of three, and are typically  
color-coded according to use: yellow for video, red for stereo right audio, and  
white for stereo left (or mono) audio. Your TVs standard A/V inputs are  
color-coded in the same manner as the cables.  
Standard stereo A/V cables  
(typically color-coded yellow for video,  
red and white for audio)  
S-Video cable is for use with video equipment that has S-Video connectors.  
Component video cables come in sets of three (typically color-coded red,  
green, and blue), and are for use with video equipment that has component video  
connectors. Your TVs ColorStream® (component video) inputs are color-coded in  
the same manner as the cables.  
S-video cable  
NOTE REGARDING PICTURE QUALITY  
When connecting video equipment to your Toshiba TV:  
For GOOD picture quality: Use a standard yellow video cable.  
Component video cables  
(typically color-coded red, green, blue)  
For BETTER picture quality: If your equipment has S-video connectors, use  
an S-video cable instead of a standard yellow video cable. (You still must  
connect the standard red and white audio cables for full system connection,  
but do not connect a standard yellow video cable at the same time or the  
picture performance will be unacceptable.)  
CAUTION: Do not plug in any power cords  
until you have finished connecting all equipment.  
For BEST picture quality: If your equipment has component video  
connectors, use component video cables instead of a standard yellow video  
cable or S-video cable. (You still must connect the standard red and white  
audio cables for full system connection.)  
Connecting a VCR  
This connection allows you to watch local channels and video pro-  
grams, play or record on the VCR while watching TV, and record  
from one channel while watching another channel.  
You will need:  
• two coaxial cables (one or more may be supplied by the cable  
company)  
• one pair of audio cables (one single audio cable for a mono VCR)  
• one video cable  
From Cable or Antenna  
TV  
Note:  
If you have a mono VCR, connect L/Mono to  
VCR Audio OUT using only one audio cable.  
ANT (75)  
If you have an S-VHS VCR, use an S-video  
cable instead of a regular video cable.  
ANT-1  
OUT  
ANT-2  
IN  
OUT  
DVD IN  
COLOR  
S-VIDEO  
Do not connect a regular video cable and an  
S-video cable to Video-1 (or Video-2) at the  
same time. Doing so will distort the picture.  
STREAM  
INPUT  
Y
VIDEO  
VIDEO  
Pb  
L/MONO  
L/MONO  
L
AUDIO  
R
AUDIO  
R
AUDIO  
R
Pr  
The unauthorized recording, use, distribution,  
or revision of television programs, videotapes,  
DVDs, and other materials is prohibited under  
the Copyright Laws of the United States and  
other countries, and may subject you to civil  
and criminal liability.  
VIDEO 2  
VIDEO 1  
Stereo VCR  
VIDEO  
AUDIO  
L
R
IN  
IN from ANT OUT to TV  
CH 3  
CH 4  
OUT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Connecting a cable converter box  
Note:  
This connection allows you to watch basic and premium cable  
channels. To use the TV features (such as PIP swap, channel y z,  
channel block, favorite channels, or channel labels ), select ANT-1. To  
view premium channels, select ANT-2, tune the TV to channel 3 or 4  
(whichever channel is vacant in your area), and use the converter box  
to change channels.  
When you use a converter box with your TV,  
the remote control may not operate certain  
features, such as PIP swap, channel y z,  
channel block, favorite channels, or channel  
labels.  
You will need:  
• three coaxial cables (one or more may be supplied by the cable  
company)  
The unauthorized recording, use, distribution,  
or revision of television programs, videotapes,  
DVDs, and other materials is prohibited under  
the Copyright Laws of the United States and  
other countries, and may subject you to civil  
and criminal liability.  
From Cable  
ANT (75)  
IN  
OUT  
DVD IN  
Cable  
Converter  
Box  
Connecting a cable converter box and VCR  
This connection allows you to watch and record basic and premium  
cable channels, as well as watch videotapes. Set the TV signal source  
to Video1 (see “Watching video input” on page 17). Tune the VCR to  
channel 3 or 4 (the same channel as the converter box output switch),  
and use the cable converter box to change channels. Set the PIP  
source to “TV” (see page 28).  
You will need:  
• five coaxial cables (one or more may be supplied by the cable  
company)  
• one pair of audio cables (one single audio cable for a mono VCR)  
• one video cable  
• one cable splitter  
From Cable  
TV  
Note:  
ANT (75)  
OUT  
OUT  
When you use a converter box with your  
TV, the remote control may not operate  
certain features, such as PIP swap,  
channel y z, channel block, favorite  
channels, or channel labels.  
Cable  
Signal  
Splitter  
IN  
ANT-1  
OUT  
ANT-2  
IN  
OUT  
DVD IN  
COLOR  
S-VIDEO  
STREAM  
INPUT  
Y
VIDEO  
VIDEO  
If you have a mono VCR, connect  
L/Mono to VCR Audio OUT using only  
one audio cable.  
Pb  
L/MONO  
L/MONO  
L
AUDIO  
R
AUDIO  
R
AUDIO  
R
Pr  
VIDEO 2  
VIDEO 1  
If you have an S-VHS VCR, use an  
S-video cable instead of a regular video  
cable.  
IN  
Cable  
Converter Box  
OUT  
Stereo VCR  
VIDEO  
AUDIO  
L
R
Do not connect a regular video cable  
and an S-video cable to Video-1 (or  
Video-2) at the same time.  
IN  
IN from ANT OUT to TV  
CH 3  
CH 4  
OUT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Connecting a DVD player or satellite receiver  
and a VCR  
This connection allows you to watch DVD/satellite, VCR, or TV  
programs. You can record from the DVD player/satellite receiver or  
TV. You can also record one TV channel while watching another  
channel.  
Note: If your DVD player has component video connections, follow  
the connection instructions under “Connecting a DVD player with  
ColorStream(component video) and a VCR” on page 10.  
You will need:  
• three coaxial cables (one or more may be supplied by the cable  
company)  
• three pairs of audio cables (one pair and two single audio cables  
for a mono VCR)  
• two regular video cables  
• one S-video cable  
Note:  
You can use a regular video cable instead of  
an S-video cable between the TV and DVD  
player/satellite receiver, but the picture quality  
will decrease.  
To Satellite  
DVD / Satellite Receiver  
The illustration at left shows one S-video  
cable and one pair of audio cables connected  
from the DVD player/satellite receiver to  
Video-1 on the TV.  
ANT (75)  
Do not connect a regular video cable and an  
S-video cable to Video-1 (or Video-2) at the  
same time. Doing so will distort the picture.  
IN  
OUT  
DVD IN  
When recording, set Audio Out to FIX  
(see “Selecting variable audio OUT”  
on page 35). With Audio Out set to  
FIX, the TV’s volume setting during  
recording will not affect the sound  
level being recorded.  
Stereo VCR  
The unauthorized recording, use, distribution,  
or revision of television programs, videotapes,  
DVDs, and other materials is prohibited under  
the Copyright Laws of the United States and  
other countries, and may subject you to civil  
and criminal liability.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
DVD Player with ColorStream (component video)  
Connecting a DVD player with  
ColorStream® (component video) and  
a VCR  
This connection allows you to watch DVD, VCR, or  
TV programs, and record DVD or TV programs  
(when authorized). You can record from one source  
while watching a program from another source.  
TV  
ANT (75)  
Your TV has ColorStream (component video) connec-  
tions. Connecting your TV to a component video  
compatible DVD player (such as a Toshiba DVD  
player with ColorStream®) can greatly enhance picture  
quality and performance.  
IN  
OUT  
DVD IN  
You will need:  
• two coaxial cables (one or more may be supplied  
by the cable company)  
• three pairs of audio cables (one pair and two  
single audio cables for a mono VCR)  
• two regular video cables  
Stereo VCR  
• one set of ColorStream (component) video cables  
Note:  
For the best picture performance, use ColorStream  
(component video) cables between the TV and DVD  
player. To record from the DVD player, the DVD player  
and TV must select VIDEO 1.  
Connecting two VCRs  
Note:  
This connection allows you to record from one VCR to another VCR  
while watching a video program. You can also record from one TV  
channel while watching another channel.  
When recording, set Audio Out to  
FIX (see “Selecting variable audio  
OUT” on page 35). With Audio Out  
set to FIX, the TV’s volume setting  
during recording will not affect the  
sound level being recorded.  
You will need:  
• two coaxial cables (one or more may be supplied by the cable  
company)  
• two pairs of audio cables (two single audio cables for mono VCRs)  
• two video cables  
Stereo VCR [Playback]  
The unauthorized recording, use, distribution,  
or revision of television programs, videotapes,  
DVDs, and other materials is prohibited under  
the Copyright Laws of the United States and  
other countries, and may subject you to civil  
and criminal liability.  
VIDEO  
AUDIO  
L
R
IN  
IN from ANT OUT to TV  
CH 3  
CH 4  
OUT  
TV  
ANT (75)  
Note:  
ANT-1  
OUT  
ANT-2  
IN  
If you have S-VHS VCRs, use S-video cables  
instead of regular video cables.  
OUT  
DVD IN  
COLOR  
S-VIDEO  
STREAM  
INPUT  
Y
Do not connect a regular video cable and an  
S-video cable to Video-1 (or Video-2) at the  
same time.  
VIDEO  
VIDEO  
Pb  
L/MONO  
AUDIO  
R
L/MONO  
L
AUDIO  
R
AUDIO  
R
Pr  
Do not connect the same VCR to the output  
and input jacks on the TV at the same time.  
VIDEO 2  
VIDEO 1  
Stereo VCR  
[Recording]  
VIDEO  
AUDIO  
L
R
IN  
IN from ANT OUT to TV  
CH 3  
CH 4  
OUT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Connecting a camcorder  
This connection allows you to watch videos recorded on a camcorder.  
Note:  
If your camcorder has an S-video connection,  
an S-video cable will provide better picture  
performance than a regular video cable.  
You will need:  
• one pair of audio cables  
• one video cable  
Do not connect a regular video cable and an  
S-video cable to Video-1 (or Video-2) at the  
same time.  
Camcorder  
S-VHS Camcorder  
VIDEO AUDIO  
S-VIDEO  
VIDEO AUDIO  
OUT  
L
OUT  
L
R
R
TV Back  
ANT (75)  
ANT-1  
OUT  
ANT-2  
IN  
OUT  
DVD IN  
COLOR  
S-VIDEO  
TV Front  
STREAM  
INPUT  
Y
VIDEO  
VIDEO  
Pb  
L/MONO  
AUDIO  
R
L/MONO  
L
VIDEO L/MONO  
AUDIO  
VIDEO-3 IN  
R
AUDIO  
R
AUDIO  
R
Pr  
VIDEO 2  
VIDEO 1  
Connecting an audio amplifier  
This connection allows you to use an audio amplifier to adjust the  
audio level. This connection also allows you to use external speakers.  
Note:  
To control the audio, both the TV and the  
amplifier must be turned on, and the volume  
of both must be set above 0, or you will not  
hear any sound. See Selecting variable audio  
OUTon page 35 for additional details.  
You will need:  
• one coaxial cable (may be supplied by the cable company)  
• one pair of audio cables  
To Cable, Cable Box,  
or Antenna  
Audio Amplifier  
The unauthorized recording, use, distribution,  
or revision of television programs, videotapes,  
DVDs, and other materials is prohibited under  
the Copyright Laws of the United States and  
other countries, and may subject you to civil  
and criminal liability.  
TV  
ANT (75)  
IN  
OUT  
DVD IN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Note:  
Using the remote control  
The remote control provided with your TV  
may or may not operate certain features on  
your VCR, cable TV converter, or other  
electronic equipment. Refer to the owner’s  
manuals provided with your other equipment  
to see which features are available. In  
addition, the other remote controls may have  
buttons not available on your TV’s remote  
control. If you would like to use those features  
or buttons, you may need to use the original  
remote controls provided with your other  
equipment.  
Preparing the remote control for use  
The remote control will operate your TV, most VCR models, and  
most cable TV converters together, even if they are different brands.  
• If you will be using your TV with a Toshiba VCR or cable TV  
converter, your remote control is already programmed and ready  
to use. See “Using the remote control with a VCR or cable TV  
converter” below.  
• If you own a non-Toshiba VCR or converter and want to use your  
TV remote control to operate it, you will need to program the  
remote control. See “Programming the remote control for use  
with a non-Toshiba VCR or cable TV converter” on page 13.  
Caution:  
• Dispose of batteries in a designated  
disposal area. Do not throw batteries  
into a fire.  
Installing the remote control batteries  
To install the batteries:  
1. Slide the battery cover off the back of the remote control.  
• Do not mix battery types or combine used  
batteries with new ones.  
• Remove dead batteries immediately to  
prevent battery acid from leaking into the  
battery compartment.  
• If you do not intend to use the remote  
control for a long time, remove the  
batteries.  
2. Install two “AA” size batteries. Match the + and – symbols on  
the batteries to the symbols on the battery compartment.  
RECALL  
POWER  
LIGHT RECALL  
POWER  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
TV/CABLE/VCR  
switch  
2
5
8
0
3
6
1
4
CH  
CH (Channel)  
Channel  
Numbers  
9
7
VOL  
CH RTN  
3. Slide the battery cover back onto the remote control until the  
lock snaps.  
ENT  
100  
ENT (used for the “ENTER”  
command with some VCRs  
and cable TV converters)  
ADV/  
PIP CH  
MENU  
.CAPT  
C
Using the remote control with a VCR  
or cable TV converter  
FAV  
ENTER  
FAV  
To control a VCR:  
RESET  
EXIT  
ADV/  
Set the TV/CABLE/VCR switch to the VCR position. The  
shaded buttons in the illustration at right will then control the  
VCR. The unshaded buttons will operate the TV as usual.  
PIP CH  
STOP  
PLAY  
STOP SOURCE  
PLAY PIP  
REC TV/VCR REW  
FF  
To control a cable TV converter:  
FAST FORWARD  
REWIND  
Set the TV/CABLE/VCR switch to the CABLE position. The  
shaded buttons in the top portion of the illustration at right will  
then control the cable TV converter.  
STILL LOCATE SWAP  
TV/VCR  
RECORD  
CT-9946  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Programming the remote control for use  
with a non-Toshiba VCR or cable TV converter  
The remote control provided with your Toshiba TV is  
preprogrammed to operate Toshiba VCRs and cable TV converters.  
RECALL  
POWER  
POWER  
LIGHT RECALL  
TV  
To operate a non-Toshiba VCR or converter using the remote  
control provided with your TV:  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
1. Refer to the VCR and cable TV converter code tables (below  
and on the next page) to find the corresponding code for your  
VCR or converter brand.  
TV/CABLE/VCR  
switch  
2
5
8
0
3
6
1
4
CH  
CH (Channel)  
If more than one code is listed, try each one separately until you  
find the one that works.  
Channel  
Numbers  
9
7
VOL  
CH RTN  
2. If you are programming the remote control to operate your:  
ENT  
100  
ENT (used for the “ENTER”  
command with some VCRs  
and cable TV converters)  
VCR: Set the TV/CABLE/VCR switch on the remote control  
to “VCR.”  
ADV/  
PIP CH  
MENU  
.CAPT  
C
Cable TV converter: Set the TV/CABLE/VCR switch on the  
remote control to “CABLE.”  
3. While holding down RECALL, press the CHANNEL  
NUMBERS to enter the three-digit code for your VCR or  
cable TV converter brand.  
4. Point the remote control at the VCR or converter, and press  
POWER to test the code.  
• If the VCR or converter responds, you entered the correct  
code.  
Note:  
Every time you replace the batteries, you  
must reprogram the remote control.  
• If the VCR or converter does not respond, repeat steps 1–4  
using another code.  
Some newer VCRs are capable of working  
on either of two remote codes. These  
VCRs have a switch labeled “VCR1/  
VCR2.” If your VCR has this kind of switch  
and does not respond to any of the codes  
for your VCR brand, set the switch to the  
other position (VCR1 or VCR2) and  
reprogram the remote control.  
5. Set the TV/CABLE/VCR switch to “TV” to control the TV.  
For future reference, write down the codes you used:  
VCR code: _____________________  
Cable TV converter code: _____________________  
VCR code table  
Brand  
Code  
Adventura  
Aiko  
Aiwa  
019  
297  
019  
CCE  
Citizen  
Colt  
091, 297  
056, 297  
091  
Fisher  
Fuji  
Funai  
066, 073, 085, 123  
052, 054  
019, 344  
Akai  
060, 068, 080, 125,  
261  
054  
259  
056  
259  
123  
206  
Craig  
056, 066, 091, 259  
054, 060, 079  
259  
039, 064, 297  
039  
019  
056  
056  
Garrard  
GE  
Go Video  
Goldstar  
Gradiente  
019, 344  
054, 079, 084, 221  
251, 298  
037, 056, 057  
019  
Curtis Mathes  
Cybernex  
Daewoo  
Daytron  
Dynatech  
Electrohome  
Electrophonic  
Emerex  
American High  
Asha  
Audiovox  
Beaumark  
Bell & Howell  
Brandt  
Harley Davidson 019  
Harman/Kardon  
Harwood  
Headquarter  
HI-Q  
057, 094  
087, 091  
065  
Broksonic  
140, 203, 230, 314,  
051  
380  
056  
054  
039  
100  
Emerson  
019, 021, 056, 062,  
080, 087, 140, 203,  
227, 228, 230, 231,  
297, 313, 314, 380,  
498  
066  
Calix  
Hitachi  
060, 061, 084, 124,  
185, 254  
060  
027, 060, 086  
057, 060, 086  
Canon  
Capehart  
Carver  
Jensen  
JVC  
Kenwood  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
VCR code table (cont.)  
Brand  
Code  
KLH  
091  
054, 056  
019, 227  
091  
Sanky  
Sansui  
Sanyo  
Scott  
058, 067  
060, 086  
Garrard  
CG Electronics  
Gemini  
General Instrument 030, 295  
Gold Star  
Hamlin  
172  
075  
034, 089  
Kodak  
Lloyd  
Logik  
LXI  
065, 066, 123, 259  
062, 064, 140, 203,  
229, 230, 231  
054, 056, 061, 065,  
066, 073, 085, 123,  
124  
067, 081  
091  
259  
091  
051, 052, 053, 054  
061  
019, 054, 062, 100,  
129  
019, 344  
060  
019, 060  
054, 181  
019, 054, 056, 071  
206  
227, 259  
056  
059, 163  
028, 039, 053, 278,  
292  
030  
026  
Magnavox  
054, 058, 100, 129,  
168  
259  
054, 100  
056  
054  
054  
019, 054, 056, 058,  
065, 066, 067, 123,  
259  
Sears  
Magnin  
Marantz  
Marta  
Matsushita  
MEI  
Hitachi  
Hytex  
Jasco  
Sharp  
Shintom  
Shogun  
Singer  
Sony  
STS  
Sylvania  
172  
Jerrold  
022, 030, 031, 033,  
034, 066, 295  
052  
046  
019  
Memorex  
Macom  
Magnavox  
Memorex  
Movietime  
NSC  
MGA  
062, 080  
175  
MGN Technology 259  
Minolta  
Mitsubishi  
Symphonic  
Tatung  
Teac  
Technics  
Teknika  
Telefunken  
TMK  
089, 175  
026, 038, 267  
019, 040, 126  
019  
044, 046, 047, 048,  
049, 050, 172  
042, 163, 552  
061, 124  
062, 080, 086, 094,  
192, 233, 261  
054, 067  
019, 259  
019, 091  
077  
Oak  
Panasonic  
Paragon  
Philips  
Motorola  
MTC  
Multitech  
NAD  
Pioneer  
Popular Mechanics 419  
Pulsar  
Toshiba  
062, 064, 085, 229,  
231, 385  
NEC  
057, 059, 060, 069,  
019  
086  
056  
259  
054  
Totevision  
Unitech  
Vector  
Vector Research  
Video Concepts  
Videosonic  
Wards  
056, 259  
259  
064  
057, 059  
059, 064, 080  
259  
019, 054, 061, 066,  
067, 081, 091, 168,  
231, 259  
019, 054, 091  
057  
052, 053, 058  
RCA  
Regal  
Recoton  
Regency  
Rembrandt  
Runco  
040  
039, 278, 292  
419  
021  
030, 089  
019  
Nikko  
Noblex  
Olympus  
Optimus  
Optonica  
Orion  
056, 067, 077, 123  
081  
498  
054, 096, 181, 244,  
473  
054, 056, 057, 059,  
061, 073, 259  
Samsung  
059, 163  
Panasonic  
Scientific Atlanta 025, 027, 036, 296  
Signal  
Signature  
SL Marx  
Sprucer  
Standard  
034, 059  
030  
059  
Penney  
XR-1000  
Yamaha  
Zenith  
Pentax  
Philco  
061, 084, 124  
054  
040  
Philips  
Pilot  
Pioneer  
Portland  
Protec  
054, 081, 100, 129  
056  
077, 086  
039  
091  
058  
065  
065  
Components  
174  
022, 034, 066  
034, 059  
034  
020  
059  
020  
031, 032, 078  
019  
034  
041, 172  
026  
Cable TV converter  
code table  
Starcom  
Stargate  
Starquest  
Sylvania  
Teleview  
Texscan  
Tocom  
Toshiba  
Tusa  
Unika  
Brand  
Code  
ABC  
020, 022, 027, 030,  
Pulsar  
032, 033, 036, 066  
Quarter  
Quartz  
Quasar  
Radio Shack  
Radix  
Antronix  
Archer  
Belcor  
041  
041, 058, 172  
075  
054, 096  
019, 056, 344  
056  
Cable Star  
Cabletenna  
Cableview  
Century  
Citizen  
075  
041  
041  
172  
Randex  
RCA  
056  
United Artists  
United Cable  
Universal  
061, 079, 084, 096,  
124, 125, 168, 221  
019, 054, 056, 065,  
066, 067, 081, 085,  
123, 259  
053  
058  
064, 259  
022  
041, 058, 075, 096,  
172, 210  
046, 079, 230  
019  
172  
Realistic  
Colour Voice  
Comtronics  
Contec  
044, 050  
059, 079  
038  
Viewstar  
Zenith  
Zentek  
Ricoh  
Runco  
Samsung  
419  
Dae Ryung  
Eastern  
027  
021  
Focus  
419  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Learning about the remote control  
LIGHT illuminates the keys  
RECALL  
POWER  
LIGHT  
POWER  
LIGHT RECALL  
RECALL displays on-screen  
information (pages 21, 22)  
TV  
TV/CABLE/VCR switch  
MUTE  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
TV/CABLE/VCR switch switches  
among TV, Cable, and VCR inputs  
(page 12)  
TIMER  
TV/VIDEO  
2
5
8
0
3
6
1
4
POWER turns the TV on and off  
CH  
CH (Channel)  
MUTE turns off the sound (page 33)  
Channel Numbers  
VOL (Volume)  
TIMER sets the TV to turn off at a specific  
time (page 31)  
9
7
VOL  
CH RTN  
ENT  
100  
CH RTN (Channel Return)  
MENU  
TV/VIDEO selects the signal input source  
(page 17)  
ADV/  
PIP CH  
MENU  
C.CAPT  
(Closed Caption)  
Channel yz cycles through  
.CAPT  
C
programmed channels (page 17)  
FAV  
PIP CH  
FAV  
ENTER  
FAV  
Channel Numbers (0–9, 100) directly  
tune channels (page 18)  
RESET  
VOL yz adjusts the volume level  
Reset  
EXIT  
EXIT  
ADV/  
PIP CH  
CH RTN (Channel Return) returns to the  
last viewed channel (page 19)  
STOP SOURCE  
PLAY PIP  
C.CAPT opens the Closed Caption menu (page 32)  
REC TV/VCR REW  
FF  
PIP (or VCR) Buttons  
MENU accesses on-screen menus (page 16)  
STILL LOCATE SWAP  
yz x • (Up/Down/Left/Right Arrows) select or adjust  
menu items when a menu is on-screen (page 17)  
FAV zy (Left/Right Arrows) select channels you  
CT-9946  
programmed as favorite channels (page 19)  
EXIT sets menu information and closes menus (page 23)  
PIP Buttons access PIP functions when the TV/Cable/  
VCR switch is set to TV (pages 28, 29)  
PIP turns the PIP and Multi-Window feature on and off  
(one press for 1/9-size PIP window; two presses for 1/16-size  
PIP window; three presses for the Multi-Window feature)  
SOURCE selects the PIP signal input source  
PIP CH yz (Up/Down Arrows) select PIP channels (when PIP  
is on-screen)  
STILL freezes the PIP display  
LOCATE changes the location of the PIP window  
SWAP switches the main and PIP pictures  
Note: When the TV/Cable/VCR switch is set to “VCR,” the PIP buttons  
function instead as VCR buttons (STOP, PLAY, REC, TV/VCR, REW, FF; see  
page 12).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
Setting up your TV  
TV Front Panel  
After installing the batteries and programming the remote control, you  
will need to set some preferences on your TV using the menu system.  
You can access the menus using the buttons on your TV or remote  
control.  
MENU  
TV / VIDEO  
VOLUME  
CHANNEL  
POWER  
When you make a menu selection, your changes occur immediately.  
You do not have to press MENU or EXIT to save your changes.  
Note: The TV front panel does not have an EXIT button.  
yzx •  
MENU  
When you are finished programming the menus, you can press  
EXIT to clear the on-screen display, or wait 15 seconds and the  
on-screen display will disappear automatically. Your changes are  
automatically saved either way.  
POWER  
LIGHT RECALL  
Changing the on-screen display language  
You can choose from three different languages (English, French, or  
Spanish) for the on-screen display of menus and messages.  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
2
5
8
0
3
6
1
To select an on-screen display language:  
1. Press MENU .  
2. Press x or until the SET UP menu appears.  
3. Press y or z to highlight LANGUAGE.  
4. Press x or to highlight your desired language.  
CH  
4
7
9
VOL  
CH RTN  
ENT  
100  
ADV/  
PIP CH  
MENU  
MENU  
.CAPT  
C
SET UP  
CONFIGURE  
FAV  
ENTER  
FAV  
LANGUAGE:  
LANGUE:  
[ENGLISH] FRANCAIS ESPANOL  
ENGLISH [FRANCAIS] ESPANOL  
ANT1/2:  
[ANT1] ANT2  
[TV] CABLE  
ANT1/2:  
[ANT1] ANT2  
[TV] CABLE  
TV/CABLE:  
CH PROGRAM  
ADD/ERASE:  
MORE  
TV/CABLE:  
PROGRAMME CAN  
ADD/EFF:  
MORE  
RESET  
EXIT  
[ADD] ERASE  
[ADD] EFF  
EXIT  
ADV/  
PIP CH  
[
]
[
]
MOVE  
SELECT  
[
]
[
]
BOUGER  
CHOISIR  
Selecting the antenna input  
You can connect to one of two different antenna input sources  
(ANT 1 or ANT 2).  
To select the antenna input:  
1. Press MENU.  
2. Press x or to highlight the SET UP menu.  
3. Press y or z to highlight ANT 1/2.  
4. Press x or to highlight either ANT 1 or ANT 2, depending on  
the antenna terminal you wish to use.  
SET UP  
LANGUAGE:  
[ENGLISH] FRANCAIS ESPANOL  
ANT1/2:  
TV/CABLE:  
CH PROGRAM  
ADD/ERASE:  
MORE  
[ANT1] ANT2  
[TV] CABLE  
[ADD] ERASE  
[
]
[
]
MOVE  
SELECT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
Selecting the signal source  
TV/VIDEO  
CHANNEL yz  
Use the TV/VIDEO button on the remote control or TV to monitor or  
change the signal source connected to your TV.  
MENU  
TV / VIDEO  
VOLUME  
CHANNEL  
POWER  
To monitor the signal source:  
Press TV/VIDEO once. The current signal source displays in green.  
To change the signal source:  
Repeatedly press TV/VIDEO to select either VIDEO 1, VIDEO 2,  
VIDEO 3, ColorStream, ANT 1, or ANT 2. The selected signal  
source displays in green.  
yzx •  
MENU  
TV  
VIDEO 1  
VIDEO 2  
VIDEO 3  
VIDEO 1  
VIDEO 2  
VIDEO 3  
ColorStream  
ANT 1  
POWER  
LIGHT RECALL  
ColorStream ANT 2  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
TV/VIDEO  
Pressing TV/VIDEO  
on the remote control  
Pressing TV/VIDEO  
on the TV  
2
5
8
0
3
6
1
4
CH  
CH (Channel)  
Programming channels into the TV’s memory  
When you press CHANNEL ▲▼ on the TV or remote control,  
the TV stops only on the channels stored in the TVs memory.  
Channel  
Numbers  
9
7
VOL  
CH RTN  
ENT  
100  
Note: To tune the TV to a channel not programmed into the memory,  
use the CHANNEL NUMBERS on the remote control.  
ADV/  
PIP CH  
MENU  
MENU  
.CAPT  
C
Follow the steps below and on the next page to program channels into  
the TVs memory.  
FAV  
ENTER  
FAV  
Programming channels automatically  
RESET  
Your TV can automatically detect all active channels in your area and  
store them in the TVs memory. After the channels are stored automati-  
cally, you can manually add or erase individual channels (see page 18).  
If you use both ANT-1 and ANT-2 terminals, you will need to program  
channels for each signal source.  
EXIT  
ADV/  
PIP CH  
To program channels automatically:  
1. Press MENU.  
2. Press x or to highlight the SET UP menu.  
3. Press y or z to highlight TV/CABLE.  
4. Press x or to highlight TV (if you use an antenna) or CABLE (if  
you use cable).  
5. Press z to highlight CH PROGRAM.  
SET UP  
SET UP  
LANGUAGE:  
LANGUAGE:  
[ENGLISH] FRANCAIS ESPANOL  
[ENGLISH] FRANCAIS ESPANOL  
ANT1/2:  
TV/CABLE:  
[ANT1] ANT2  
[TV] CABLE  
ANT1/2:  
TV/CABLE:  
[ANT1] ANT2  
[TV] CABLE  
CH PROGRAM  
ADD/ERASE:  
MORE  
CH PROGRAM  
ADD/ERASE:  
MORE  
[ADD] ERASE  
[ADD] ERASE  
[
]
[
]
[
]
[
]
MOVE  
SELECT  
MOVE  
SELECT  
6. Press x or to start automatic channel programming (CH PRO-  
GRAMdisplays on-screen). The TV automatically cycles through  
every TV or cable channel (depending on which you selected), and  
stores all active channels in the TVs memory.  
7. When automatic channel programming is complete, the message  
CH Programming Completedappears.  
8. Press CHANNEL ▲▼ to view the programmed channels.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
Adding and erasing channels manually  
After you have automatically programmed the channels into the TVs  
CHANNEL yz  
memory, you can manually add and erase individual channels.  
MENU  
TV / VIDEO  
VOLUME  
CHANNEL  
POWER  
To add a channel to or erase a channel from the TVs memory:  
1. Tune the TV to the channel you want to add or erase. If you are  
adding a channel, you will need to use the CHANNEL  
NUMBERS to select the channel.  
yzx •  
MENU  
2. Press MENU.  
3. Press x or to highlight the SET UP menu.  
4. Press y or z to highlight ADD/ERASE.  
SET UP  
LANGUAGE:  
POWER  
LIGHT RECALL  
[ENGLISH] FRANCAIS ESPANOL  
ANT1/2:  
TV/CABLE:  
[ANT1] ANT2  
[TV] CABLE  
TV  
CH PROGRAM  
ADD/ERASE: [ADD] ERASE  
MORE  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
[
]
[
]
MOVE  
SELECT  
2
5
8
0
3
6
1
5. Press x or to highlight ADD or ERASE, whichever function  
CH  
CH (Channel)  
4
7
you want to perform.  
Channel  
Numbers  
6. Press MENU.  
7. Repeat steps 16 for other channels you want to add or erase,  
9
VOL  
CH RTN  
ENT  
100  
or press EXIT to return to normal TV viewing.  
ADV/  
PIP CH  
MENU  
MENU  
.CAPT  
C
Changing channels  
To change to the next programmed channel:  
Press CHANNEL yz.  
FAV  
ENTER  
FAV  
RESET  
EXIT  
ADV/  
PIP CH  
EXIT  
To change to a specific channel (programmed or unprogrammed):  
Press the CHANNEL NUMBERS (09 and 100).  
Note: For channels 100 and higher, press the 100 button, and  
then the next two channel numbers (for example, to select  
channel 100, press 100, 0, 0; to select channel 125, press  
100, 2, 5).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
Using the TV’s features  
POWER  
LIGHT RECALL  
Adjusting the channel settings  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
Switching between two channels  
You can switch between two channels without entering an actual  
channel number each time.  
2
5
8
0
3
6
1
4
CH  
CH (Channel)  
To switch between two channels:  
1. Select the first channel you want to view.  
Channel  
Numbers  
9
7
VOL  
CH RTN  
2. Select a second channel using the CHANNEL NUMBERS  
ENT  
100  
CH RTN  
MENU  
(09 and 100).  
ADV/  
PIP CH  
MENU  
3. Press CH RTN (channel return). The previous channel will  
.CAPT  
C
display.  
Every time you press CH RTN, the TV will switch back and forth  
between the last two channels you tuned the TV to.  
FAV  
ENTER  
FAV  
FAV  
RESET  
EXIT  
ADV/  
PIP CH  
EXIT  
Programming your favorite channels  
The Favorite Channel feature allows you to use the FAV ▼▲ buttons  
on the remote control to cycle through your favorite channels,  
skipping over channels you do not normally watch. You can program  
a maximum of 12 favorite channels.  
Note: You can still use CHANNEL ▲▼ to cycle through all the  
channels you previously programmed into the TVs memory (see  
Adding channels to the TVs memoryon page 17).  
To program your favorite channels:  
1. Tune the TV to a channel you want to program as a favorite  
channel.  
2. Press MENU.  
3. Press x or to highlight the SET UP menu.  
4. Press y or z to highlight FAVORITE CH.  
SET UP  
MORE  
V-CHIP CONTROL  
FAVORITE CH  
CH LABEL  
VIDEO LABEL  
TIMER:  
DEMO:  
0 MIN  
START [STOP]  
[
]
[
]
MOVE  
START  
5. Press x or to display the FAVORITE CH menu. SET/CLEAR  
will be highlighted.  
6. Press x or to highlight SET.  
7. Press z to add the current channel to the list.  
8. Press MENU.  
SET UP  
FAVORITE CH  
[SET] CLEAR  
2
0
0
5
0
0
6
0
0
11  
0
0
[TV: CYAN, CABLE: BLUE]  
[
]
[
]
SELECT  
SET  
9. Repeat steps 18 for up to 12 channels, or press EXIT to close  
the menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
To select your favorite channels:  
Note:  
Press FAV zy on the remote control to cycle through the favorite  
channels you programmed.  
The FAV zy buttons function as menu x •  
buttons when a menu is on-screen.  
Note: The FAV zy buttons will not work unless you program at  
least one favorite channel.  
To clear a favorite channel:  
1. Tune the TV to the channel you want to clear from your favorite  
channel list.  
POWER  
LIGHT RECALL  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
2. Press MENU.  
3. Press x or to highlight the SET UP menu.  
4. Press y or z to highlight FAVORITE CH.  
2
5
8
0
3
6
1
4
CH  
5. Press x or to display the FAVORITE CH menu. SET/CLEAR  
will be highlighted.  
9
7
6. Press x or to highlight CLEAR.  
VOL  
CH RTN  
ENT  
100  
ADV/  
PIP CH  
MENU  
SET UP  
MENU  
.CAPT  
FAVORITE CH  
SET [CLEAR]  
C
2
0
0
5
0
0
6
0
0
0
0
0
FAV  
ENTER  
FAV  
FAV  
[TV: CYAN, CABLE: BLUE]  
RESET  
[
]
[
]
SELECT  
CLEAR  
EXIT  
ADV/  
PIP CH  
EXIT  
7. Press z to clear the current channel number from the list.  
8. Press MENU.  
9. Repeat steps 18 for other channels you want to clear from your  
favorite channel list, or press EXIT to close the menu.  
Using the V-Chip Control (blocking) feature  
You can use the V-Chip Control feature to block certain programs or  
channels, to prevent others from viewing them.  
Selecting a PIN code  
Before you can block programs or channels, you must select a personal  
identification number (PIN) code. Your PIN code allows you to access  
the V-Chip Control menu, and prevents others from changing the  
rating and blocking limits you set.  
To select your PIN code and access the V-Chip Control menu:  
1. Press MENU.  
2. Press x or to highlight the SET UP menu.  
3. Press y or z to highlight V-CHIP CONTROL.  
4. Press x or to display the Enter PIN Codescreen.  
SET UP  
SET UP  
MORE  
BLOCKING IS ACTIVE  
PLEASE ENTER PIN CODE  
_ _ _ _  
V-CHIP CONTROL  
FAVORITE CH  
CH LABEL  
VIDEO LABEL  
TIMER:  
0 MIN  
START [STOP]  
DEMO:  
[
]
SELECT [0–9] END [EXIT]  
[
]
MOVE  
START  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
5. Use the CHANNEL NUMBERS (09) to enter your four-digit  
PIN code. After the code is entered, the V-Chip Control menu  
appears.  
RECALL  
POWER  
LIGHT RECALL  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
SET UP  
2
5
8
0
3
6
1
4
ENABLE BLOCKING [Y] N  
SET RATING  
SET BLOCKING OPTIONS  
NEW PIN CODE  
BLOCK CHANNEL  
VIDEO LOCK  
CH  
Channel  
Numbers  
OFF  
[
9
7
VOL  
CH RTN  
]
[
]
MOVE  
SELECT  
ENT  
100  
V-Chip Control (Blocking) Menu  
ADV/  
PIP CH  
MENU  
MENU  
6. Press y or z to highlight ENABLE BLOCKING.  
.CAPT  
C
7. Press x or to highlight Y,which enables all blocking by  
activating the V-Chip. See Blocking programs by ratingson  
page 22, Blocking unrated movies or programson page 23,  
and Blocking channelson page 24.  
FAV  
ENTER  
FAV  
RESET  
EXIT  
ADV/  
PIP CH  
EXIT  
(Note: Highlight Nto deactivate the V-Chip Control feature  
and disable blocking.)  
Changing your PIN code  
1. Press MENU.  
Note:  
If you forget your PIN code:  
2. Press x or to highlight the SET UP menu.  
3. Press y or z to highlight V-CHIP CONTROL.  
4. Press x or to display the Enter PIN Code screen.  
• Follow steps 1–4 under “Changing your PIN  
code” at left.  
• Then press RECALL four times within five  
seconds.  
5. Use the Channel Number buttons (09) to enter your existing  
PIN code. After the code is entered, the V-Chip Control menu  
appears.  
This allows you to proceed to the V-Chip  
Control menu and reset your PIN code.  
6. Press y or z to highlight NEW PIN CODE.  
7. Press x or to display the New PIN Code screen.  
SET UP  
SET UP  
ENABLE BLOCKING  
SET RATING  
SET BLOCKING OPTIONS  
NEW PIN CODE  
BLOCK CHANNEL  
[Y] N  
PLEASE ENTER NEW PIN CODE  
_ _ _ _  
VIDEO LOCK  
OFF  
SELECT [0–9] END [EXIT]  
[
]
[
]
MOVE  
SELECT  
8. Use the CHANNEL NUMBERS (09) to enter a new PIN  
code. After the new code is entered, the V-Chip Control menu  
appears.  
9. Press EXIT to return to normal TV viewing.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
Blocking programs by ratings  
Note:  
The Motion Picture Association of America (MPAA) uses a rating  
system to qualify motion picture content. Television broadcasters  
employ a similar rating system to qualify the content of television  
programs. The MPAA, Youth TV, and TV ratings work with the  
V-Chip feature to allow you to block access to programs that exceed  
the rating limits you set.  
Press RECALL to see the rating of the program  
you are viewing. Not all programs are rated,  
however. To block programs or movies that are  
not rated, see “Blocking unrated movies and  
programs” on page 23.  
Ratings definitions  
MPAA Ratings  
TV Ratings  
MA  
Mature audience only. This program is specifically  
designed to be viewed by adults and therefore  
may be unsuitable for children under 17.  
X
For adults only.  
NC17  
R
Not intended for anyone 17 or under.  
Restricted. Under 17 requires an accompanying  
parent or adult guardian.  
Dialog  
Intensely suggestive dialog  
Language Crude or indecent language  
Sex  
Violence  
PG13  
PG  
Parents strongly cautioned. Some material may  
not be appropriate for children under 13.  
Explicit sexual activity  
Graphic violence  
Parental guidance suggested. Some material  
may not be appropriate for children.  
14  
Parents strongly cautioned. This program contains  
some material that many parents would find  
unsuitable for children under 14 years of age.  
G
General audience. Appropriate for all ages.  
Dialog  
Frequent suggestive dialog  
Youth TV Ratings  
Language Frequent coarse language  
Y7, Y7FV  
Directed to older children. Programs rated Y7  
Sex  
Violence  
Intense sexual situations  
Intense violence  
are designed for children 7 and above.  
Programs rated Y7FV contain fantasy violence  
that may be more intense or combative than  
Y7-rated programs.  
PG  
Parental guidance suggested. This program  
contains material that parents may find unsuitable  
for younger children.  
Y
For all children. Programs rated Y are designed  
to be appropriate for all children.  
Dialog  
Some suggestive dialog  
Language Occasional coarse language  
Sex  
Violence  
Some sexual situations  
Moderate violence  
G
General audience. Most parents would find this  
program suitable for all ages.  
No DLSV Programs without any Dialog, Language, Sex, or  
Violence ratings.  
To block programs by rating:  
1. Press MENU.  
2. Press x or to highlight the SET UP menu.  
3. Press y or z to highlight V-CHIP CONTROL.  
4. Press x or to display the Enter PIN Codescreen.  
RECALL  
POWER  
LIGHT RECALL  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
5. Use the CHANNEL NUMBERS (09) to enter your four-digit PIN  
code. After the code is entered, the V-Chip Control menu appears.  
2
5
8
0
3
6
1
4
6. Press y or z to highlight ENABLE BLOCKING.  
CH  
7. Press x or to highlight Y,which enables all blocking by activating  
the V-Chip. (Note: Highlight Nto deactivate the V-Chip Control  
feature and disable blocking.)  
Channel  
Numbers  
9
7
VOL  
CH RTN  
ENT  
100  
ADV/  
PIP CH  
MENU  
MENU  
SET UP  
.CAPT  
C
ENABLE BLOCKING [Y] N  
SET RATING  
SET BLOCKING OPTIONS  
NEW PIN CODE  
BLOCK CHANNEL  
FAV  
ENTER  
FAV  
VIDEO LOCK  
OFF  
RESET  
[
]
[
]
MOVE  
SELECT  
EXIT  
ADV/  
PIP CH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
8. Press y or z to highlight SET RATING.  
9. Press x or to display the Set Rating menu.  
10. Press y or z to highlight MPAA Rating, Youth TV Rating, or  
POWER  
LIGHT RECALL  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
TV Rating.  
11. Press to select (or x to deselect) the ratings to be blocked.  
Blocked ratings will be marked with x; unblocked ratings will  
will be marked with .All ratings higher than the ones that are  
selected (x) are blocked as well. For example, if you block the  
MPAA rating R, programs with the higher ratings NC17 and X  
will also be blocked.  
MUTE  
2
5
8
0
3
6
1
4
CH  
9
7
VOL  
CH RTN  
ENT  
100  
ADV/  
PIP CH  
MENU  
MENU  
SET UP  
SET UP  
.CAPT  
C
MPAA RATING:  
TV RATING:  
DIALOG:  
MA 14 PG  
x
G
X
NC17 R PG13 PG  
G
x x  
LANGUAGE:  
SEX:  
FAV  
ENTER  
FAV  
YOUTH TV RATING:  
VIOLENCE:  
NO DLSV:  
Y
Y7FV Y7  
BACK TO V-CHIP MENU  
TV RATING  
RESET  
[
]
[
]
[
]
[
]
MOVE  
SELECT  
MOVE  
SELECT  
EXIT  
EXIT  
ADV/  
PIP CH  
12. When you finish selecting the program ratings to be blocked:  
To return to the V-Chip menu, press y or z to highlight  
BACK TO V-CHIP MENU, and then press x or .  
To return to normal TV viewing, press EXIT.  
Unblocking programs temporarily  
When you try to view a program with a ratings block, a message  
appears stating that the program has been blocked because the  
programs rating exceeds the set limits. To temporarily override the  
block and view the program, press MUTE and enter your PIN code.  
To reset your original ratings blocks, turn the TV off and then on  
again.  
THIS PROGRAM HAS BEEN BLOCKED  
TV-PG  
BLOCKING IS ACTIVE  
PLEASE ENTER PIN CODE  
TO TE_MP_OR_AR_ILY UN-BLOCK  
L
V
EXCEEDS SET LIMITS  
PUSH MUTE TO ENTER PIN  
SELECT [0–9] END [EXIT]  
Blocking unrated movies and programs  
Some movies and programs are not rated. You can use the V-Chip  
Control feature to block unrated movies and programs.  
To block unrated movies and programs:  
1. Press MENU.  
2. Press x or to highlight the SET UP menu.  
3. Press y or z to highlight V-CHIP CONTROL.  
4. Press x or to display the Enter PIN Code screen.  
5. Use the CHANNEL NUMBERS (09) to enter your four-digit  
PIN code. After entering the code, the V-Chip Control menu  
appears.  
6. Press y or z to highlight ENABLE BLOCKING.  
(Continued on next page)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
7. Press x or to highlight Y,which enables all blocking by  
activating the V-Chip. (Note: Highlight Nto deactivate the  
V-Chip feature and disable blocking.)  
8. Press y or z to highlight SET BLOCKING OPTIONS.  
9. Press x or to display the unrated movie/program blocking menu.  
10. Press y or z to highlight BLOCK TV NONE RATING.  
11. Press x or to highlight Yto block movies/programs rated  
TV None.(Note: Highlight Nto unblock unrated programs.)  
12. Press EXIT to return to normal TV viewing.  
SET UP  
SET UP  
ENABLE BLOCKING  
SET RATING  
[Y] N  
BLOCK MPAA UNRATED:  
[Y] N  
[Y] N  
BLOCK TV NONE RATING:  
BACK TO V-CHIP MENU  
SET BLOCKING OPTIONS  
NEW PIN CODE  
BLOCK CHANNEL  
NOTICE: ENABLING THIS OPTION  
MAY BLOCK EMERGENCY  
MESSAGES  
Caution:  
VIDEO LOCK  
OFF  
[
Blocking unrated television programs (those  
rated “TV NONE”) may block emergency  
messages.  
]
[
]
[
]
[
]
MOVE  
SELECT  
MOVE  
SELECT  
Blocking channels  
You can block a maximum of four TV channels and four cable  
channels. Blocked channels cannot be viewed, regardless of their  
ratings. If you try to tune the TV to a blocked channel, the nearest  
unblocked channel will display.  
Note:  
After programming CHANNEL BLOCK, tune  
the TV to a channel that is not blocked before  
turning the TV off.  
To block a channel:  
1. Tune the TV to the channel you want to block.  
2. Press MENU.  
3. Press x or to highlight the SET UP menu.  
4. Press y or z to highlight V-CHIP CONTROL.  
5. Press x or to display the Enter PIN Code screen.  
POWER  
LIGHT RECALL  
TV  
6. Use the CHANNEL NUMBERS (09) to enter your four-digit  
PIN code. After entering the code, the V-Chip Control menu  
appears.  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
2
5
8
0
3
6
1
4
7. Press y or z to highlight ENABLE BLOCKING.  
CH  
8. Press x or to highlight Y,which enables all blocking by  
activating the V-Chip Control feature. (Note: Highlight Nto  
deactivate the V-Chip feature and disable blocking.)  
Channel  
Numbers  
9
7
VOL  
CH RTN  
9. Press y or z to highlight BLOCK CHANNEL.  
ENT  
100  
10. Press x or to display the BLOCK CHANNEL menu.  
ADV/  
PIP CH  
MENU  
MENU  
SET/CLEAR will be highlighted.  
.CAPT  
C
11. Press x or to highlight SET.  
FAV  
ENTER  
FAV  
12. Press z to add the current channel to the list.  
RESET  
EXIT  
ADV/  
PIP CH  
EXIT  
SET UP  
BLOCK CHANNEL  
[SET] CLEAR  
0
0
0
6
[
]
[
]
SELECT  
SET  
END [EXIT]  
13. Press MENU.  
14. Press EXIT.  
15. Repeat steps 114 to block additional channels.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
To unblock all blocked channels:  
POWER  
LIGHT RECALL  
Note: This will unblock every channel you have blocked. You cannot  
unblock individual channels.  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
1. Press MENU.  
2. Press x or to highlight the SET UP menu.  
3. Press y or z to highlight V-CHIP CONTROL.  
4. Press x or to display the Enter PIN Code screen.  
2
5
8
0
3
6
1
4
CH  
Channel  
Numbers  
5. Use the CHANNEL NUMBERS (09) to enter your four-digit  
PIN code. After entering the code, the V-Chip Control menu  
appears.  
9
7
VOL  
CH RTN  
ENT  
100  
6. Press y or z to highlight BLOCK CHANNEL.  
ADV/  
PIP CH  
MENU  
MENU  
.CAPT  
7. Press x or to display the BLOCK CHANNEL menu.  
C
SET/CLEAR will be highlighted.  
FAV  
ENTER  
FAV  
8. Press x or to highlight CLEAR.  
9. Press z to clear all blocked channels from the list.  
10. Press MENU.  
RESET  
EXIT  
ADV/  
PIP CH  
EXIT  
11. Press EXIT to return to normal TV viewing.  
Locking video inputs  
You can use the Video Lock feature to block the input sources  
(Video 1, Video 2, Video 3, and ColorStream) and channels 3 and 4.  
Note: The Video Lock feature is independent of the Enable Blocking  
option of V-Chip control (page 21).  
Note:  
The Video Lock options are:  
In normal TV viewing, if you cannot access the  
input sources (Video 1, Video 2, Video 3, and  
ColorStream) or channels 3 and 4, check the  
Video Lock setting and highlight OFF if  
necessary.  
Video: Blocks Video 1, Video 2, Video 3, and ColorStream.  
Video+: Blocks Video 1, Video 2, Video 3, ColorStream, and  
channels 3 and 4.  
Off:  
Disables the Video Lock feature.  
To set up video lock:  
1. Press MENU.  
2. Press x or to highlight the SET UP menu.  
3. Press y or z to highlight V-CHIP CONTROL.  
4. Press x or to display the Enter PIN Code screen.  
5. Use the CHANNEL NUMBERS (09) to enter your four-digit  
PIN code. After entering the code, the V-Chip Control menu  
appears.  
6. Press y or z to highlight VIDEO LOCK.  
7. Press x or to select the desired level of video locking (Video,  
Video+, or Off).  
SET UP  
ENABLE BLOCKING [Y] N  
SET RATING  
SET BLOCKING OPTIONS  
NEW PIN CODE  
BLOCK CHANNEL  
VIDEO LOCK  
VIDEO VIDEO+ [OFF]  
[
]
[
]
MOVE  
SELECT  
8. Press EXIT to return to normal TV viewing.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
Channel labels  
RECALL  
POWER  
LIGHT RECALL  
You can assign labels to a maximum of 32 channels. Each channel  
label can have a maximum of four characters.  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
For example, if channel 8 is your public television station, you could  
create the label PBSfor that channel. The label PBSwould then  
appear on-screen when you tune the TV to channel 8.  
2
5
8
0
3
6
1
4
CH  
Channel labels appear on-screen above the channel number every time  
you turn the TV on, change the channel, or press RECALL.  
Channel  
Numbers  
9
7
VOL  
To create a channel label:  
1. Tune the TV to the channel you want to label.  
2. Press MENU.  
CH RTN  
ENT  
100  
ADV/  
PIP CH  
MENU  
MENU  
.CAPT  
C
3. Press x or to highlight the SET UP menu.  
4. Press y or z to highlight CH LABEL.  
FAV  
ENTER  
FAV  
RESET  
EXIT  
SET UP  
ADV/  
PIP CH  
EXIT  
MORE  
V-CHIP CONTROL  
FAVORITE CH  
CH LABEL  
VIDEO LABEL  
TIMER:  
DEMO:  
0 MIN  
START [STOP]  
[
]
[
]
MOVE  
START  
5. Press x or to display the CH LABEL menu. SET/CLEAR will  
be highlighted.  
6. Press x or to highlight SET.  
7. Press z to highlight LABEL.  
SET UP  
SET UP  
CH LABEL  
SET/CLEAR  
CH LABEL  
SET/CLEAR  
LABEL  
[SET] CLEAR  
_ _ _ _  
[SET] CLEAR  
_ _ _ _  
LABEL  
SET UP MENU  
SET UP MENU  
[
]
[
]
MOVE  
SET [ENT]  
SELECT  
[
]
[
]
MOVE  
SELECT  
8. Press x or repeatedly to scan through the list of available  
characters until the desired character appears in the first space.  
9. Press MENU.  
10. Repeat steps 8 and 9 to enter the rest of the characters.  
Note: For a blank space in the label name, you must choose a  
blank space from the list of characters; otherwise, a dash will  
appear in the space.  
11. Repeat steps 110 for up to 32 channels.  
12. Press EXIT to return to normal TV viewing.  
To erase a channel label:  
1. Select the channel whose label you want to erase.  
2. Press MENU.  
3. Press x or to highlight the SET UP menu.  
4. Press y or z to highlight CH LABEL.  
5. Press x or to display the CH LABEL menu. SET/CLEAR will  
be highlighted.  
6. Press x or to highlight CLEAR.  
7. Press MENU.  
8. Repeat steps 17 to erase other channel labels, or press EXIT to  
return to normal TV viewing.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
Video labels  
POWER  
LIGHT RECALL  
The Video Label feature allows you to label each input source for your  
TV, from the following preset list of labels:  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
:  
Uses the default label name  
VCR: Video cassette recorder  
DVD: Digital video disc or digital versatile disc  
DTV: Digital TV set-top box  
SAT: Satellite box  
2
5
8
0
3
6
1
4
CH  
9
7
VOL  
CH RTN  
CBL: Cable box  
ENT  
100  
ADV/  
PIP CH  
To set up video labels:  
1. Press MENU.  
MENU  
MENU  
.CAPT  
C
2. Press x or to highlight the SET UP menu.  
3. Press y or z to highlight VIDEO LABEL.  
4. Press x or to display the Video Label screen.  
FAV  
ENTER  
FAV  
RESET  
EXIT  
EXIT  
ADV/  
PIP CH  
5. Press y or z to highlight the input source to be labeled  
(VIDEO 1, VIDEO 2, VIDEO 3, or ColorStream).  
6. Press x or to select the desired label for that input source.  
SET UP  
VIDEO LABEL  
VIDEO1  
– VCR DVD DTV [SAT] CBL  
VIDEO2  
VIDEO3  
ColorStream  
SET UP MENU  
[
]
[
]
MOVE  
SELECT  
7. Repeat steps 16 to label the other input sources.  
8. When you finish setting up video labels:  
To return to the previous menu, press y or z to highlight  
SET UP MENU, and then press x or .  
To return to normal TV viewing, press EXIT.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
Watching picture-in-picture (PIP)  
The picture-in-picture (PIP) feature allows you to watch two pictures  
at the same time. The small PIP window can display a signal from a  
TV broadcast or an external source, such as a VCR.  
Note:  
The PIP window will not open when a  
ColorStream (component video) source is  
being viewed.  
To display a TV broadcast in the PIP window:  
1. Tune the TV to the program you want to watch in the main  
window.  
2. Press PIP to display a small picture (one press displays a PIP  
window 1/9 the size of the screen; two presses display a 1/16-size  
window).  
POWER  
LIGHT RECALL  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
2
5
8
0
3
6
1
4
CH  
CH (Channel)  
1/9 1/16  
PIP  
7
9
7
VOL  
CH RTN  
ENT  
100  
3. Press PIP CH yz to change the PIP channel. Press Channel yz  
ADV/  
PIP CH  
MENU  
to change the main channel.  
.CAPT  
C
To display an external source in the PIP window:  
1. Connect the external equipment to the ANT-1 connection on  
the TV.  
FAV  
ENTER  
FAV  
PIP CH  
RESET  
EXIT  
Note: An ANT-2 source will not display as a PIP. For connection  
ADV/  
PIP CH  
information, see “Connecting your TV” on page 7.  
SOURCE  
PIP  
STOP SOURCE  
PLAY PIP  
2. Turn on the TV and select the program/source you want to watch  
in the main window.  
REC TV/VCR REW  
FF  
SWAP  
3. Press PIP (one press to display a PIP window 1/9 the size of the  
STILL LOCATE SWAP  
screen; two presses to display a 1/16-size window).  
4. Press SOURCE to select the PIP input source (TV, VIDEO 1,  
VIDEO 2, or VIDEO 3). The current source will display  
on-screen in green.  
CT-9946  
PIP  
TV  
VIDEO1  
VIDEO2  
VIDEO3  
TO SELECT PUSH SOURCE  
To turn PIP off:  
Press PIP two or three times, depending on the PIP window size  
you selected.  
Switching the main and small pictures  
With the TV in PIP mode, repeatedly press SWAP to switch the  
main and small pictures back and forth.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28  
Changing the location of the PIP window  
ADV/  
With the TV in PIP mode, press LOCATE to change the location of  
the PIP window on-screen. Every time you press LOCATE, the PIP  
window changes position counter-clockwise.  
PIP CH  
MENU  
.CAPT  
C
FAV  
ENTER  
FAV  
PIP CH  
RESET  
EXIT  
ADV/  
PIP CH  
SOURCE  
PIP  
STOP SOURCE  
PLAY PIP  
REC TV/VCR REW  
FF  
SWAP  
STILL LOCATE SWAP  
LOCATE  
STILL  
CT-9946  
Freezing the PIP display  
With the TV in PIP mode, press STILL to freeze the PIP display. The  
PIP picture becomes still, and is outlined in red on-screen. Press  
STILL again to restore the moving picture (outlined in green).  
Still  
Watching multi-window PIP  
Note:  
Multi-window PIP displays channels  
programmed for the signal source you are  
currently viewing (ANT-1 or Cable).  
Multi-window PIP appears as six small boxes across the bottom of the  
screen. The multi-window PIP displays only the channels you  
programmed into the TVs memory (see Adding channels to the TVs  
memoryon page 17).  
Note: The LOCATE, SWAP, PIP CHANNEL yz, SOURCE,  
and STILL buttons do not function in multi-window PIP mode.  
To view multi-window PIP:  
Press PIP three times.  
The TV cycles through all of the programmed channels, showing a  
few seconds of each channels programming, and then freezes the  
image and moves on to the next channel in a continuous cycle. The  
channel number appears above each PIP window.  
Note:  
If V-Chip blocking is enabled when  
you view multi-window PIP, channels  
exceeding the rating limits will appear  
as a black window with a red “X.”  
14  
23  
27 30  
43  
56  
X
To turn multi-window PIP off:  
Press PIP again, or change the channel.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
Adjusting the picture  
MENU  
TV / VIDEO  
VOLUME  
CHANNEL  
POWER  
Adjusting the picture quality  
You can adjust the pictures contrast, brightness, sharpness, color, and  
tint. Your picture quality adjustments are stored automatically in the  
TVs memory. You can keep these settings or choose preset options in  
the PREFERENCE menu (see Selecting the color temperature”  
below, and Adjusting the picture preferenceon the next page.)  
yzx •  
MENU  
To adjust the picture quality:  
POWER  
LIGHT RECALL  
1. Press MENU.  
2. Press x or to highlight the PICTURE menu.  
3. Press y or z until the quality you want to adjust is highlighted.  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
2
5
8
0
3
6
1
4
CH  
PICTURE  
Note:  
CONTRAST 50  
BRIGHTNESS 50  
SHARPNESS 50  
COLOR  
TINT  
+
To reset the picture (and audio)  
adjustments to the factory settings,  
select RESET in the PICTURE menu.  
9
7
VOL  
50  
0
CH RTN  
ENT  
100  
RESET  
[
]
[
]
MOVE  
ADJUST  
ADV/  
PIP CH  
MENU  
MENU  
.CAPT  
C
4. Press x or to adjust the level, as described in the following table:  
FAV  
ENTER  
FAV  
Selection  
Pressing  
Contrast  
Brightness  
Sharpness  
Color  
Lower  
Higher  
RESET  
EXIT  
Darker  
Softer  
Paler  
Lighter  
Sharper  
Deeper  
Greenish  
ADV/  
PIP CH  
Tint  
Reddish  
Selecting the color temperature  
You can change the picture quality by selecting from three preset color  
temperaturescool, medium, and warmas described in the  
following table:  
Mode  
Picture Quality  
Cool  
Medium  
Warm  
Blueish  
Neutral  
Reddish  
To select the color temperature:  
1. Press MENU.  
2. Press x or to highlight the PREFERENCE menu.  
3. Press y or z to highlight COLOR TEMPERATURE.  
4. Press x or to highlight the mode you prefer.  
PREFERENCE  
COLOR TEMPERATURE  
[COOL] MEDIUM WARM  
PICTURE PREFERENCE  
[SPORTS] STANDARD MOVIE MEMORY  
[
]
[
]
MOVE  
SELECT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30  
Adjusting the picture preference  
MENU  
TV / VIDEO  
VOLUME  
CHANNEL  
POWER  
You can select four picture modesSports, Standard, Movie, and  
Memoryas described in the following table:  
Mode  
Picture Quality  
Sports  
Bright and dynamic picture (factory-set)  
Standard picture quality (factory-set)  
Standard  
Movie  
Memory  
yzx •  
MENU  
Movie-like picture setting (factory-set)  
Your personal preferences (set by you; see  
Adjusting the picture quality” on page 30.)  
To select your picture preference:  
1. Press MENU.  
2. Press x or to highlight the PREFERENCE menu.  
3. Press y or z to highlight PICTURE PREFERENCE.  
4. Press x or to highlight the mode you prefer.  
RECALL  
TIMER  
POWER  
LIGHT RECALL  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
2
5
8
0
3
6
1
4
CH  
PREFERENCE  
9
7
COLOR TEMPERATURE  
[COOL] MEDIUM WARM  
VOL  
CH RTN  
PICTURE PREFERENCE  
[SPORTS] STANDARD MOVIE MEMORY  
ENT  
100  
ADV/  
PIP CH  
MENU  
MENU  
[
]
[
]
.CAPT  
MOVE  
SELECT  
C
FAV  
ENTER  
FAV  
Displaying on-screen information  
RESET  
Press RECALL to display the following information on-screen:  
Antenna mode (when in TV mode)  
Channel number or video mode  
EXIT  
EXIT  
ADV/  
PIP CH  
Channel label (if set)  
Audio status (stereo or SAP)  
Rating of current program (if rated)  
Setting the off timer  
The off timer turns the TV off automatically.  
To set the off timer:  
1. Press TIMER.  
2. Press to increase (or x to decrease) the amount of time until the  
TV turns off automatically (in 10-minute increments, to a  
maximum of 180).  
3. Press EXIT to exit the menu and return to normal TV viewing.  
To cancel the off timer:  
Set the off timer to 0 (zero) minutes in step 2 above, or turn the  
TV off and then on again.  
Auto power off  
The TV turns itself off automatically after approximately 15 minutes if  
it is tuned to a vacant channel or a station that stops broadcasting for  
the day.  
Note: The auto power off feature does not work in VIDEO mode.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
Using the closed caption feature  
The Closed Caption feature has two options:  
POWER  
LIGHT RECALL  
CaptionsAn on-screen display of the dialogue, narration, and  
sound effects of programs and videos that are closed-captioned  
(usually identified in your local TV listing as CC).  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
TextAn on-screen display of information not related to the  
program, such as weather or stock data (if available in your  
viewing area).  
2
5
8
0
3
6
1
4
CH  
To view captions or text:  
1. Tune the TV to the desired program.  
9
7
VOL  
CH RTN  
ENT  
100  
2. Press C.CAPT (or press MENU, and then press x or to  
C.CAPT  
MENU  
highlight the CLOSED CAPTION menu).  
ADV/  
PIP CH  
MENU  
.CAPT  
3. Press y or z to highlight CC.  
C
FAV  
ENTER  
FAV  
CLOSED CAPTI0N  
RESET  
CC:  
C1 C2 C3 C4 T1  
T2 T3 T4 [OFF]  
EXIT  
ADV/  
PIP CH  
[
]
[
]
MOVE  
SELECT  
Note:  
4. Press x or to select the desired Closed Caption mode, as  
A closed caption signal may not display in the  
following situations:  
follows:  
To view captions, select C1, C2, C3, or C4 (C1 displays  
translation of the primary language in your area). Note: If the  
program or video you selected is not closed-captioned, no  
captions will display on the screen.  
When a videotape has been dubbed  
When the signal reception is weak  
When the signal reception is non-  
standard  
The top of the mountain is covered  
with snow all the year round.  
To view text, select T1, T2, T3, or T4. Note: If text is not  
available in your viewing area, a black rectangle may appear on  
your screen. If this occurs, turn the Closed Caption feature off.  
WORLD WEATHER  
Temps  
F
Current  
Weather  
Clear  
C
LONDON  
MOSCOW  
PARIS  
51  
11  
14  
12  
19  
18  
57  
Cloudy  
Clear  
53  
66  
ROME  
TOKYO  
Cloudy  
Rain  
65  
To turn the Closed Caption feature off, highlight OFF in the  
Closed Caption menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
32  
Adjusting the sound  
RECALL  
MUTE  
POWER  
LIGHT RECALL  
Muting the sound  
TV  
CABLE  
VCR  
Press MUTE to temporarily turn off the sound. While the sound is off,  
the screen displays the word MUTEin the lower /right corner. To  
restore the sound, press MUTE or VOLUME yz.  
When you press MUTE, the Closed Caption feature is automatically  
activated. To deactivate captions and restore normal sound, press  
MUTE again. This feature works only when the Closed Caption mode  
is set to OFF. See Using the closed captioned featureon page 40 for  
more information about closed caption settings.  
MUTE TV/VIDEO TIMER  
2
5
8
0
3
6
1
4
CH  
9
7
VOL  
VOL  
CH RTN  
ENT  
100  
Selecting stereo/SAP broadcasts  
ADV/  
PIP CH  
MENU  
MENU  
.CAPT  
The multi-channel TV sound (MTS) feature provides high-fidelity  
stereo sound. MTS also can transmit a second audio program (SAP)  
containing a second language or other audio information.  
Note: The MTS feature is not available in VIDEO mode.  
C
FAV  
ENTER  
FAV  
RESET  
In general, you can leave your TV in stereo mode because the TV  
automatically outputs either stereo or monaural (mono) sound,  
depending on the broadcast type.  
EXIT  
ADV/  
PIP CH  
When the TV receives a stereo or SAP broadcast, the word STEREO”  
or SAPdisplays on the screen every time you turn the TV on,  
change the channel, or press RECALL.  
To listen to stereo sound:  
1. Press MENU.  
2. Press x or to highlight the AUDIO menu.  
3. Press y or z to highlight MTS.  
4. Press x or to highlight STR (stereo).  
Note: If the stereo sound is noisy, select MONO to reduce the  
noise.  
AUDIO  
MTS:  
[STR] SAP MONO  
50  
50  
0
BASS  
TREBLE  
BALANCE  
SURROUND: [ON] OFF  
AUDIO OUT: [FIX] VARIABLE  
MORE  
[
]
[
]
MOVE  
SELECT  
To listen to a second audio program (SAP):  
1. Press MENU.  
2. Press x or to highlight the AUDIO menu.  
3. Press y or z to highlight MTS.  
4. Press x or to highlight SAP. The TV speakers will output only  
the second audio program.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
Adjusting the sound quality  
You can change the sound quality of your TV by adjusting the bass,  
treble, and balance.  
Note:  
To reset the audio adjustments (bass, treble,  
and balance) to the factory settings, select  
RESET in the PICTURE menu (see page 30).  
To adjust the sound quality:  
1. Press MENU.  
2. Press x or to highlight the AUDIO menu.  
3. Press y or z to highlight the quality you want to adjust.  
4. Press x or to adjust the level:  
MENU  
TV / VIDEO  
VOLUME  
CHANNEL  
POWER  
x makes the sound quality weaker or decreases the balance in  
the right channel, depending on the item selected.  
makes the sound quality stronger or decreases the balance in  
the left channel, depending on the item selected.  
yzx •  
MENU  
POWER  
LIGHT RECALL  
AUDIO  
TV  
MTS:  
[STR] SAP MONO  
CABLE  
VCR  
+
BASS  
TREBLE  
BALANCE  
50  
50  
0
MUTE TV/VIDEO TIMER  
SURROUND: [ON] OFF  
AUDIO OUT: [FIX] VARIABLE  
MORE  
2
5
8
0
3
6
1
4
[
]
[
]
MOVE  
ADJUST  
CH  
Using the surround sound feature  
9
7
VOL  
CH RTN  
The surround sound feature expands the audio listening field wider and  
deeper to create exceptional sound quality from the TV speakers.  
This feature uses stereo signals from a TV broadcast or video input.  
ENT  
100  
ADV/  
PIP CH  
MENU  
MENU  
.CAPT  
C
To turn the surround sound feature on:  
1. Press MENU.  
FAV  
ENTER  
FAV  
2. Press x or to highlight the AUDIO menu.  
RESET  
3. If you have not already done so, select STEREO mode (press y or  
EXIT  
ADV/  
PIP CH  
z to highlight MTS, and then press x or to highlight STR).  
4. Press y or z to highlight SURROUND.  
5. Press x or to highlight ON.  
AUDIO  
MTS:  
[STR] SAP MONO  
BASS  
TREBLE  
BALANCE  
50  
50  
0
SURROUND: [ON] OFF  
AUDIO OUT: [FIX] VARIABLE  
MORE  
[
]
[
]
MOVE  
SELECT  
To turn the surround sound feature off:  
Highlight OFF in step 5 above. Note: In general, you can leave the  
surround sound feature on because it automatically outputs surround  
stereo or monaural sound, depending on the broadcast or video type.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
34  
Selecting variable audio OUT  
If you connect external audio equipment (such as a stereo  
audio amplifier or surround sound system) to the TVs Audio OUT  
jack, you can use the AUDIO OUT feature to select either variable or  
fixed audio output.  
MENU  
TV / VIDEO  
VOLUME  
CHANNEL  
POWER  
If you set AUDIO OUT to VARIABLE, you can use the volume  
controls on either the TV or the audio equipment to adjust the  
sound level coming through the audio equipment.  
yzx •  
MENU  
If you set AUDIO OUT to FIX, you must use the volume controls  
on the audio equipment to adjust the sound level coming through  
the audio equipment (the TVs volume setting will have no effect).  
POWER  
LIGHT RECALL  
Note: Fixed audio output provides a cleaner signal than variable audio  
output.  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
See page 11 for details on connecting an audio amplifier to the TVs  
Audio OUT jack.  
2
5
8
0
3
6
1
4
To select variable audio output:  
1. Press MENU.  
2. Press x or to highlight the AUDIO menu.  
3. Press y or z to highlight AUDIO OUT.  
4. Press x or to highlight VARIABLE.  
CH  
9
7
VOL  
CH RTN  
ENT  
100  
ADV/  
PIP CH  
MENU  
MENU  
.CAPT  
C
AUDIO  
MTS:  
BASS  
TREBLE  
BALANCE  
[STR] SAP MONO  
FAV  
ENTER  
FAV  
50  
50  
0
SURROUND: [ON] OFF  
RESET  
AUDIO OUT: FIX [VARIABLE]  
MORE  
EXIT  
ADV/  
PIP CH  
[
]
[
]
MOVE  
SELECT  
To select fixed audio output:  
1. Highlight FIX in step 4 above.  
Turning off the built-in speakers  
Use this feature to turn off the TVs built-in speakers when you  
connect external speakers to your TV (see Connecting an audio  
amplifieron page 11).  
To turn off the built-in speakers:  
1. Press MENU.  
2. Press x or to highlight the AUDIO menu.  
3. Press y or z to highlight SPEAKERS.  
4. Press x or to highlight OFF.  
AUDIO  
MORE  
SPEAKERS: ON [OFF]  
SBS:  
SBS LEVEL:  
[ON] OFF  
50  
[
]
[
]
MOVE  
SELECT  
To turn on the built-in speakers:  
1. Highlight ON in step 4 above.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35  
Using the sub-bass system (SBS)  
The sub-base system (SBS) allows you to enhance bass performance,  
even when the volume is low.  
RECALL  
POWER  
POWER  
LIGHT RECALL  
TV  
CABLE  
VCR  
MUTE TV/VIDEO TIMER  
To turn the sub-bass system on (or off):  
1. Press MENU.  
2. Press x or to highlight the AUDIO menu.  
3. Press y or z to highlight SBS.  
4. Press x or to highlight ON (or OFF).  
2
5
8
0
3
6
1
4
CH  
9
7
VOL  
CH RTN  
ENT  
100  
AUDIO  
ADV/  
PIP CH  
MENU  
MENU  
MORE  
SPEAKERS:  
[ON] OFF  
.CAPT  
C
SBS:  
SBS LEVEL:  
[ON] OFF  
50  
FAV  
ENTER  
FAV  
[
]
[
]
MOVE  
SELECT  
RESET  
EXIT  
EXIT  
ADV/  
PIP CH  
To adjust the sub-bass system:  
1. Turn the sub-bass system on, as instructed above.  
2. Press MENU.  
3. Press x or to highlight the AUDIO menu.  
4. Press y or z to highlight SBS LEVEL.  
5. Press x or to adjust the SBS level.  
AUDIO  
MORE  
SPEAKERS:  
SBS:  
[ON] OFF  
[ON] OFF  
+
SBS LEVEL: 50  
[
]
[
]
MOVE  
ADJUST  
Viewing the demonstration (DEMO) mode  
The demonstration (DEMO) mode is an option available on the  
SET UP menu that will demonstrate several features of your TV.  
To start the demonstration mode:  
1. Press MENU.  
2. Press x or to highlight the SET UP menu.  
3. Press y or z to highlight DEMO.  
4. Press x or to highlight START.  
4. Press MENU to start the demo.  
To stop the demonstration mode:  
Press RECALL, EXIT, or POWER.  
Understanding the last mode memory feature  
If the power is cut off while you are viewing the TV, the Last Mode  
Memory feature turns the TV on automatically when the power is  
resupplied.  
If the power is going to be off for a long time and you are going to be  
away from your TV, unplug the power cord to prevent the TV from  
turning on in your absence.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
36  
Appendix  
Troubleshooting  
Before calling a service technician, please check the following table for possible causes of the problem and  
some solutions.  
Problem  
Solution  
TV will not turn on  
Make sure the power cord is plugged in, and then press POWER.  
The remote control batteries may be dead. Replace the batteries or  
press the POWER button on the TV.  
No picture, no sound  
No sound, picture OK  
Check the antenna/cable connections.  
The sound may be muted. Press MUTE or VOLUME y z.  
The station may have broadcast difficulties. Try another channel.  
Poor sound, picture OK  
Poor picture, sound OK  
The station may have broadcast difficulties. Try another channel.  
Check the antenna connections.  
The station may have broadcast difficulties. Try another channel.  
Adjust the PICTURE menu.  
Poor reception of broadcast channels  
The station may have broadcast difficulties. Try another channel.  
Check the antenna connections.  
If you are using a VCR, make sure the TV/VCR button is set  
correctly.  
Cannot receive above channel 13  
Unable to select a certain channel  
Make sure TV/CABLE is set to TV mode.  
The channel may be locked out with the channel lock feature, or  
erased with the add/erase feature.  
Multiple images  
The station may have broadcast difficulties. Try another channel.  
Use a highly directional outdoor antenna.  
Poor color or no color  
The station may have broadcast difficulties. Try another channel.  
Adjust the TINT and/or COLOR in the PICTURE menu.  
If you change the direction of the TV while it is turned on, the  
picture could suffer from color shading. If so, turn the TV off and  
allow it to cool down for several hours before turning it on again.  
No stereo or SAP sound from a  
known MTS broadcast  
Make sure the MTS feature is set properly.  
The remote control does not operate  
Check that the TV/CABLE/VCR switch is properly set.  
There may be an obstruction between the remote control and the  
remote control sensor.  
The remote control batteries may be dead. Replace the batteries.  
The V-Chip PIN code does not work  
Change or reset your PIN code.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37  
Specifications  
Television system  
Channel coverage  
NTSC standard  
VHF:  
UHF:  
2 through 13  
14 through 69  
Cable TV: Mid band (A-8 through A-1, A through 1)  
Super band (J through W)  
Hyper band (AA through ZZ, AAA, BBB)  
Ultra band (65 through 94, 100 through 125)  
Power source  
120 AC, 60 Hz  
Power consumption  
Audio power  
96 W  
5 W + 5 W  
Speaker type  
2-3/8 x 4-3/4 inches (60 x 120 mm)  
ColorStream® (component video) INPUT  
Video/Audio terminals  
Y: 1V (p-p), 75 ohm  
C
R
(PR): 0.7 V (p-p), 75 ohm  
(PB): 0.7 V (p-p), 75 ohm  
CB  
S-VIDEO INPUT  
Y-INPUT: 1 V (p-p), 75 ohm, negative sync.  
C-INPUT: 0.286 V (p-p) (burst signal), 75 ohm  
VIDEO/AUDIO INPUT  
VIDEO: 1 V (p-p), 75 ohm, negative sync.  
AUDIO: 150 mV (rms) (30% modulation equivalent, 47 k ohm)  
VIDEO/AUDIO OUTPUT  
VIDEO: 1 V (p-p), 75 ohm, negative sync.  
AUDIO: 150 mV (rms) (30% modulation equivalent, 47 k ohm)  
Dimensions  
Width: 38-3/16 inches (970 mm)  
Height: 30-1/16 inches (764 mm)  
Depth: 25-1/4 inches (641 mm)  
Weight  
154 lbs (69.9 kg)  
Supplied accessories  
Optional TV stand  
Remote control with two size AAbatteries  
ST-3642  
Design and specifications are subject to change without notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
38  
Limited United States Warranty  
for 27'' FST PURE® and All Larger Television Models  
Toshiba America Consumer Products, Inc. (“TACP”) and Toshiba  
(4) Labor service charges for set installation, setup, adjustment of  
customer controls, and installation or repair of antenna systems  
are not covered by these warranties. Reception problems  
caused by inadequate antenna systems are your responsibility.  
Hawaii, Inc. (“THI”) make the following limited warranties to original  
consumers in the United States. THESE LIMITED WARRANTIES  
EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR  
ANY PERSON RECEIVING THIS TELEVISION AS A GIFT FROM  
THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER  
PURCHASER OR TRANSFEREE.  
(5) Warranties extend only to defects in materials or workmanship  
as limited above and do not extend to any television or parts that  
have been lost or discarded by you or to damage to television or  
parts caused by misuse, accident, Acts of God (such as lightning  
or fluctuations in electric power), improper installation, improper  
maintenance, or use in violation of instructions furnished by  
TACP/THI; or to units that have been modified or had the serial  
number removed, altered, defaced, or rendered illegible.  
PRODUCTS PURCHASED IN THE U.S.A. AND USED IN  
CANADA ARE NOT COVERED BY THESE WARRANTIES.  
PRODUCTS PURCHASED IN CANADA AND USED IN THE  
U.S.A. ARE NOT COVERED BY THESE WARRANTIES.  
Limited One (1) Year Warranty on Parts and Labor*  
How to Obtain Warranty Services  
TACP/THI warrant this television and its parts against defects in  
materials or workmanship for a period of one (1) year after the date  
of original retail purchase. DURING THIS PERIOD, TACP/THI  
WILL, AT TACP/THI’S OPTION, REPAIR OR REPLACE A  
DEFECTIVE PART WITH A NEW OR REFURBISHED PART  
WITHOUT CHARGE TO YOU FOR PARTS OR LABOR. TACP/THI  
Authorized Service Station personnel will come to your home  
when warranty service is required. Depending on the type of repair  
required, either the service will be performed in your home or the  
set will be taken to the TACP/THI Authorized Service Station for  
repair and returned to your home at no cost to you.  
If, after following all of the operating instructions in this manual  
and checking the “Troubleshooting” section, you find that service  
is needed:  
(1) To find the nearest TACP/THI Authorized Service Station:  
For televisions purchased in the United States, except Hawaii,  
visit TACP’s web site at www.toshiba.com/tacp, or call toll  
free 1-800-631-3811.  
For televisions purchased in Hawaii, contact Toshiba Hawaii, Inc.,  
327 Kamakee Street, Honolulu, HI 96814, (808) 591-9281.  
(2) Present your bill of sale or other proof of purchase to the  
Authorized Service Station. Authorized TACP/THI Service Station  
personnel will come to your home when warranty service is  
required. Depending on the type of repair required, either the  
service will be performed in your home or the set will be taken to  
the Authorized Service Station for repair and returned to your  
home at no cost to you.  
Limited Two (2) Year Warranty on Picture Tube*  
TACP/THI further warrant the picture tube in this television against  
defects in materials or workmanship for a period of two (2) years  
after the date of original retail purchase. DURING THIS PERIOD,  
TACP/THI WILL, AT TACP/THI’S OPTION, REPAIR OR REPLACE  
A DEFECTIVE PICTURE TUBE WITH A NEW OR REFURBISHED  
PICTURE TUBE WITHOUT CHARGE TO YOU, EXCEPT THAT, IF  
A DEFECTIVE PICTURE TUBE IS REPAIRED OR REPLACED  
AFTER ONE (1) YEAR FROM THE DATE OF THE ORIGINAL  
RETAIL PURCHASE, YOU PAY LABOR CHARGES INVOLVED  
IN THE REPAIR OR REPLACEMENT.  
For additional information, visit TACP’s web site:  
ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE  
OF THE U.S.A., INCLUDING THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF  
THE LIMITED WARRANTIES SET FORTH ABOVE. WITH THE  
EXCEPTION OF ANY WARRANTIES IMPLIED BY THE LAW  
OF ANY STATE OF THE U.S.A. AS HEREBY LIMITED, THE  
FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL  
OTHER WARRANTIES, GUARANTEES, AGREEMENTS, AND  
SIMILAR OBLIGATIONS OF TACP OR THI WITH RESPECT TO  
THE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO EVENT  
SHALL TACP OR THI BE LIABLE FOR CONSEQUENTIAL OR  
INCIDENTAL DAMAGES.  
Rental Units  
The warranty for rental units begins with the date of first rental  
or thirty (30) days from the date of shipment to the rental firm,  
whichever comes first.  
*Commercial Units  
Televisions sold and used for commercial purposes have a limited  
ninety (90) day warranty for all parts, labor, and picture tubes.  
No person, agent, distributor, dealer, or company is authorized  
to change, modify, or extend the terms of these warranties in  
any manner whatsoever. The time within which action must be  
commenced to enforce any obligation of TACP or THI arising under  
this warranty or under any law of the United States or of any state  
thereof is hereby limited to 90 days from the date you discover, or  
should have discovered, the defect. This limitation does not apply to  
implied warranties arising under the law of any state of the U.S.A.  
Owner’s Manual and Product Registration Card  
Read this owner’s manual thoroughly before operating this television.  
Complete and mail the enclosed product registration card within ten  
days after you, or the person who has given you this product as a  
gift, purchased this television. Returning the product registration  
card will enable TACP/THI to provide you with better customer  
service and improved product support. Failure to return the product  
registration card will not affect your rights under this warranty.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND  
YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY  
FROM STATE TO STATE IN THE U.S.A. SOME STATES OF THE  
U.S.A. DO NOT ALLOW LIMITATIONS ON THE DURATION OF  
AN IMPLIED WARRANTY, LIMITATIONS ON THE TIME WITHIN  
WHICH AN ACTION MAY BE BROUGHT, OR THE EXCLUSION  
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES; THEREFORE, THE ABOVE LIMITATIONS OR  
EXCLUSIONS MAY NOT APPLY TO YOU UNDER SUCH  
CIRCUMSTANCES.  
Your Responsibility  
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING  
CONDITIONS:  
(1) You must provide your bill of sale or other proof of purchase.  
(2) All warranty servicing of this television must be made by an  
Authorized TACP/THI Service Station.  
(3) The warranties from TACP and THI are effective only if the  
television is purchased and operated in the U.S.A. or Puerto  
Rico.  
FST PURE® is a registered trademark of Toshiba America Consumer Products, Inc.  
REV. MAR02  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
Limited Canada Warranty  
for 27'' FST PURE® and All Larger Television Models  
Toshiba of Canada Limited (“TCL) makes the following limited  
warranties to original consumers in Canada.  
(4) Labor service charges for set installation, setup, adjustment of  
customer controls, and installation or repair of antenna systems  
are not covered by these warranties. Reception problems  
caused by inadequate antenna systems are your responsibility.  
THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL  
CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS  
TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER  
PURCHASER AND TO NO OTHER PURCHASER OR  
TRANSFEREE.  
(5) Warranties extend only to defects in materials or workmanship  
as limited above and do not extend to any television or parts that  
have been lost or discarded by you or to damage to television or  
parts caused by misuse, accident, Acts of God (such as lightning  
or fluctuations in electric power), improper installation, improper  
maintenance, or use in violation of instructions furnished by TCL;  
or to units that have been modified or had the serial number  
removed, altered, defaced, or rendered illegible.  
PRODUCTS PURCHASED IN THE U.S.A. AND USED IN  
CANADA ARE NOT COVERED BY THESE WARRANTIES.  
PRODUCTS PURCHASED IN CANADA AND USED IN THE  
U.S.A. ARE NOT COVERED BY THESE WARRANTIES.  
How to Obtain Warranty Services  
Limited One (1) Year Warranty on Parts and Labor*  
If, after following all of the operating instructions in this manual and  
checking the “Troubleshooting” section, you find that service is  
needed:  
TCL warrants this television and its parts against defects in materials  
or workmanship for a period of one (1) year after the date of original  
retail purchase. DURING THIS PERIOD, TCL WILL, AT TCLS  
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A  
NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU  
FOR PARTS OR LABOR. TCL Authorized Service Depot personnel  
will come to your home when warranty service is required.  
Depending on the type of repair required, either the service will  
be performed in your home or the set will be taken to the TCL  
Authorized Service Depot for repair and returned to your home at  
no cost to you. IN-HOME SERVICE ONLY APPLIES WITHIN 100  
KILOMETERS OF AN AUTHORIZED TCL SERVICE DEPOT.  
(1) To find the nearest TCL Authorized Service Depot, visit TCLs  
web site: www.toshiba.ca.  
(2) Present your bill of sale or other proof of purchase to the  
Authorized Service Depot. Authorized TCL Service Depot  
personnel will come to your home when warranty service is  
required. Depending on the type of repair required, either the  
service will be performed in your home or the set will be taken  
to the Authorized Service Depot for repair and returned to your  
home at no cost to you. IN-HOME SERVICE ONLY APPLIES  
WITHIN 100 KILOMETERS OF AN AUTHORIZED TCL  
SERVICE DEPOT.  
Limited Two (2) Year Warranty on Picture Tube*  
For additional information, visit TCLs web site:  
TCL further warrants the picture tube in this television against  
defects in materials or workmanship for a period of two (2) years  
after the date of original retail purchase. DURING THIS PERIOD,  
TCL WILL, AT TCLS OPTION, REPAIR OR REPLACE A  
DEFECTIVE PICTURE TUBE WITH A NEW OR REFURBISHED  
PICTURE TUBE WITHOUT CHARGE TO YOU, EXCEPT THAT,  
IF A DEFECTIVE PICTURE TUBE IS REPAIRED OR REPLACED  
AFTER ONE (1) YEAR FROM THE DATE OF THE ORIGINAL  
RETAIL PURCHASE, YOU PAY LABOR CHARGES INVOLVED  
IN THE REPAIR OR REPLACEMENT.  
ALL WARRANTIES IMPLIED BY THE LAW OF ANY PROVINCE  
OF CANADA, INCLUDING THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF  
THE LIMITED WARRANTIES SET FORTH ABOVE. WITH THE  
EXCEPTION OF ANY WARRANTIES IMPLIED BY THE LAW  
OF ANY PROVINCE OF CANADA AS HEREBY LIMITED, THE  
FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL  
OTHER WARRANTIES, GUARANTEES, AGREEMENTS, AND  
SIMILAR OBLIGATIONS OF TCL WITH RESPECT TO THE  
REPAIR OR REPLACEMENT OF ANY PARTS. IN NO EVENT  
SHALL TCL BE LIABLE FOR CONSEQUENTIAL OR  
Rental Units  
The warranty for rental units begins with the date of first rental or  
thirty (30) days from the date of shipment to the rental firm,  
whichever comes first.  
INCIDENTAL DAMAGES.  
No person, agent, distributor, dealer, or company is authorized  
to change, modify, or extend the terms of these warranties in  
any manner whatsoever. The time within which action must be  
commenced to enforce any obligation of TCL arising under this  
warranty or under any law of Canada or of any province thereof,  
is hereby limited to 90 days from the date you discover, or should  
have discovered, the defect. This limitation does not apply to implied  
warranties arising under the law of any province of Canada.  
*Commercial Units  
Televisions sold and used for commercial purposes have a limited  
ninety (90) day warranty for all parts, labor, and picture tubes.  
Owner’s Manual  
Read this owner’s manual thoroughly before operating this television.  
Your Responsibility  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,  
AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY  
VARY FROM PROVINCE TO PROVINCE IN CANADA. SOME  
PROVINCES OF CANADA DO NOT ALLOW LIMITATIONS ON  
THE DURATION OF AN IMPLIED WARRANTY, LIMITATIONS  
ON THE TIME WITHIN WHICH AN ACTION MAY BE BROUGHT,  
OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR  
CONSEQUENTIAL DAMAGES; THEREFORE, THE ABOVE  
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU  
UNDER SUCH CIRCUMSTANCES.  
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING  
CONDITIONS:  
(1) You must provide your bill of sale or other proof of purchase.  
(2) All warranty servicing of this television must be made by an  
Authorized TCL Service Depot.  
(3) The warranties from TCL are effective only if the television is  
purchased in Canada from an authorized TCL dealer and  
operated in Canada.  
FST PURE® is a registered trademark of Toshiba America Consumer Products, Inc.  
REV. MAR02  
Download from Www.Somanuals.com. All Manuals Search And Download.  
40  
TOSHIBA AMERICA CONSUMER PRODUCTS, INC.  
HEAD OFFICE: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A.  
NATIONAL SERVICE DIVISION: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A.  
TOSHIBA HAWAII, INC.  
HEAD OFFICE: 327 KAMAKEE STREET, HONOLULU, HI 96814, U.S.A. — TEL: (808) 591-9281  
TOSHIBA OF CANADA LTD.  
HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA — TEL: (905) 470-5400  
SERVICE CENTERS:  
TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA — TEL: (905) 470-5400  
MONTREAL: 1643 NORTH SERVICE RD., TRANS-CANADA HIGHWAY, DORVAL QUEBEC, H9P 1J1, CANADA — TEL: (514) 856-4100  
VANCOUVER: 22171 FRASERWOOD WAY, RICHMOND, B.C., V6W 1J5, CANADA — TEL: (604) 303-2500  
MANUFACTURED BY  
TOSHIBA AMERICA CONSUMER PRODUCTS, INC.  
ColorStream is a registered trademark of Toshiba America Consumer Products, Inc.  
PRINTED IN USA  
(02-06)B  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Teledyne TV Converter Box gfc 7000t User Manual
Toshiba Home Security System camera control unit User Manual
Toshiba Security Camera Domo PTZ User Manual
TP Link Switch TL SG5412F User Manual
TP Link Weather Radio TL WR710N User Manual
Transcend Information Network Card TS2GSD150 User Manual
Triarch Indoor Furnishings 25692 25693 25694 User Manual
Vermont Casting Indoor Fireplace DTV38s2 User Manual
Vornado Computer Accessories D9478A User Manual
Watlow Electric Water Heater Firerod Immersion User Manual