Top Innovations, Inc.
Innovative Products to Make Your Life Easier
Model SP-402
Owner’s Manual
THIS IS NOT A TOY!
Adult supervision recommended
Item contains sharp functional points and small parts
ꢀMachine Sewing in Minutes
ꢀAdjustable Stitch Length
ꢀSews with a Durable Lockstitch
Top Innovations, Inc.
400 NW Platte Valley Drive Riverside, MO 64150
(800) 711-6617 (816) 584-9700 Fax: (816) 584-9066
Download from Www.Somanuals.com. All Manuals Search And Download.
QUIKSTITCH PARTS AND ACCESSORIES
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES INCLUDED
1. In Accessory Drawer in front of machine
ꢀ3 Bobbins (1 in machine)
For replacement, use class 66 bobbins
ꢀ1 needle threader
ꢀ2 needles (1 in machine)
For replacement needles, use size 14 needles
ꢀCombination seam ripper/thread trimmer
2. AC Adaptor
3. Foot Pedal
4
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
Even if you have sewn before, these instructions will make
your first use much easier!
TABLE OF CONTENTS
PAGE
Handy Reference Guide.................................................................2
Getting Ready to Sew ....................................................................6
Winding the Bobbin........................................................................7
Inserting the Wound Bobbin...........................................................9
Threading the Machine ..................................................................10
Raising the Bobbin Thread.............................................................12
Sewing a Broken Seam..................................................................13
Securing a Seam............................................................................14
Free Arm Sewing............................................................................14
Adjusting Tension...........................................................................15
Changing Needles..........................................................................16
Bobbin Case Replacement ............................................................17
Performance Checklist...................................................................18
Limited Warranty............................................................................19
IMPORTANT SAFEGUARDS
ꢀBefore connecting machine, be sure that the voltage on the AC adaptor
matches your electrical supply
ꢀAlways disconnect the foot pedal or AC adaptor when changing needles,
removing the bobbin, or cleaning the QUIKSTITCH
ꢀAlways disconnect the AC adaptor whenever the QUIKSTITCH is
unattended
ꢀWork carefully and watch the sewing area to avoid the needle during
operation
ꢀDo not pull the fabric while sewing as the needle may bend, break or
cause other damage
ꢀInsure that the machine is threaded correctly before sewing
ꢀThe QUIKSTITCH is a sewing machine and is not intended for garment
construction
5
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING READY TO SEW
1. Assemble spool holder by
snapping spool pin into spool
stand. Both of these parts are
found in accessory drawer located
in front of machine
2. Slide spool stand into its holder
on rear left of machine, until it
snaps firmly into place
3. Make sure that power switch is in
the “O” (Off) position. Plug in the
foot pedal and AC adaptor plug
4. Remove the red-handled seam
ripper/thread trimmer and needle
threader from accessory drawer
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WINDING THE BOBBIN
1. Push the bobbin winder switch
down to raise bobbin winder
2. Remove see-through bobbin
cover by sliding it toward the front
of machine.
Insure that the bobbin case is in
the proper position. The bobbin
case is held in place by a position
plate, which is designed to flex
slightly to allow the bobbin case to
move back and forth freely, about
1/16”.
The screw head should line up
with the seam in plastic casing of
machine and bobbin case should
move back and forth slightly
(about 1/16”) when hand wheel is
turned. If not, refer to page 17 for
repositioning instructions.
3. Remove empty bobbin from
bobbin case. The seam ripper
may make removal easier. Place
bobbin on the bobbin winder,
aligning the hole in bobbin with
the driving pin on bobbin winder.
You may have to turn the hand
wheel to help locate the driving
pin.
4. Slide spool of thread onto the
spool pin. NOTE: Make certain
that the thread retaining slit on
spool is near the bottom.
Otherwise, thread can become
caught in the slit and cause
problems during sewing.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Pull thread from spool and, using
two hands, pull it through the
diagonal slit in first thread guide
First thread guide should look like
this when properly threaded.
6. Wrap thread one time
counterclockwise around
tension disc.
7. Feed end of thread through small
hole in top of bobbin from the
inside, leaving a 3” tail.
8. Slide power switch into “1” (On)
position.
Hold the end of the thread (the
“tail”) firmly and step on foot pedal
until a few coils are wound onto
bobbin and stop.
9. Use the thread trimmer to cut off
tail, so it is flush with the top of
the bobbin. Continue winding
until the desired amount of thread
is wound onto bobbin. A full
bobbin holds 35 yards.
10. Cuts thread about 4” from the
bobbin and remove it from the
machine. Leave the spool of
thread on spool pin on back of
machine. Push bobbin winder
switch up into “Off” position.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSERTING THE WOUND BOBBIN
1. Insert wound bobbin into bobbin
case with thread spooling off to
left side, as shown.
2. Guide end of thread to the back of
the bobbin.
3. Pull the thread toward you so that
it hooks on notch A (at 3 o’clock
position) and then pull to the left
so that it passes through notch B
(at 4 o’clock position)
4. Leave several inches of thread
laying across top of bobbin toward
the left of machine.
Bobbin threading is now complete.
(See page 12 to raise lower thread for
sewing)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
THREADING THE MACHINE
There are six thread guides that the
top thread passes through. The
diagram at right shows an overview of
the threading procedure; refer to the
specific instructions below for
important details.
Your spool of thread should be in the
same position as it was for winding
the bobbin- on the spool pin on the
back of the machine. Cut the thread
near the spool and pull the tail out of
the thread guide and tension disc.
1. Pull thread from spool, (using two
hands); pull it through diagonal slit
in thread guide “A”. Do not wrap
thread around tension disc for
sewing.
Thread guide “A” should look like
this when properly threaded.
2. Hold thread firmly against top of
machine between thread guides
“A” and “B” and pull down in
between two silver discs.
3. Feed the thread under disc thread
guide “C” and through opening
created by guide bar.
Insert thread from right to left.
Leave some slack in the thread to
the right.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Grasp slack thread (while
removing slack); guide the thread
into the center groove in disc
thread guide “C”. NOTE: Make
sure that thread does not slip
behind the guide.
Pull about 6” of thread through
and ensure that the threading is
correct up to this point.
5. Turn the hand wheel toward you
until take-up lever is in its highest
position. Pass the thread through
the hole in take-up lever “D” from
right to left.
6. Turn the hand wheel toward you
so that needle lowers and the
thread guide “E” is accessible.
Place the thread behind the
thread guide “E” to the right side
and pull forward. The thread
guide will thread itself.
7. Turn the hand wheel toward you
again to raise the needle to its
highest position.
Feed wire needle threader
through needle eye from right to
left.
Insert thread through wire loop and pull
needle threader through the needle eye.
Now pull thread back to the right.
The needle is now threaded.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
RAISING THE BOBBIN THREAD
1. Hold top (needle) thread and turn
hand wheel toward you until
needle goes to its lowest and then
its highest point.
Raise the presser foot using the
presser bar lifter.
2. Gently pull top (needle) thread
until lower (bobbin) thread comes
up in the form of a loop.
3. Use the flat side of seam
ripper/thread trimmer to open up
bobbin thread loop until end is
visible.
4. Pull both thread tails straight back
under presser foot.
5. Replace see-though bobbin cover
by sliding it back into place.
You are now ready to sew!
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SEWING A BROKEN SEAM
1. Set the stitch control knob to the
desired stitch length. For most
sewing, the “long stitch” setting is
acceptable.
Turn hand wheel toward you to
raise the needle to the highest
position.
2. Lift presser foot using presser bar
lifter. Make sure that both needle
(top) thread and bobbin (lower)
thread are pulled straight back
behind needle about 4”.
3. Position area to be sewed under
presser foot. Turn the hand
wheel toward you to lower the
needle into existing stitches in
fabric. Lower presser foot.
4. Step on foot pedal and the
machine will start to sew the
broken seam. Continue until new
stitches are about an inch past
the area to be sewed and then
step off the foot pedal.
5. Raise presser foot using presser
bar lifter and pull fabric straight
back. Cut both threads about 4”
from the edge of the fabric.
NOTE: If it is difficult to pull thread
toward back without noticeably
bending the needle, a slight
backward and forward movement
of the hand wheel will make it
easier to remove the fabric.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SECURING A SEAM
There are two methods of securing
the threads at the start and the end of
the repaired seam.
METHOD #1 : Backstitching
Turn the stitch control knob to
REVERSE (left) position and
backstitch 4-5 stitches at start and
end of seam repair.
METHOD #2: Tying off
When seam is completed, use needle
threader to pull top thread to
underside of fabric. Tie a square knot
with the bobbin thread and trim.
FREE ARM SEWING
The QUIKSTITCH has a free arm for
sewing sleeves, pant legs, etc .. To
utilize this handy feature, just slip the
item onto the free arm.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING TENSION
All tension adjustment is accomplished
by using the needle thread tension dial.
The bobbin case tension is pre-set at
the factory and cannot be adjusted.
ALWAYS DOUBLE CHECK
THREADING BEFORE
ATTEMPTING TO ADJUST
TENSION!
The tension level may be determined by
using two different color threads for
the needle and bobbin threads, and
then analyzing the resulting stitches.
When an even amount of thread is exerted on both threads, a smooth, even
stitch known as a balanced stitch is produced.
A perfect, balanced stitch will have the needle and bobbin threads locked
between the two layers of fabric with no loops on top or bottom and no
puckering.
Too much tension will produce a tight stitch, which will cause the fabric to
pucker. To decrease tension, turn the tension dial downwards.
Too little tension will produce a loose stitch, which will cause loops in your
seam. To increase tension, turn the dial upwards.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING NEEDLES
IMPORTANT: use size 14 needles.
1. Turn hand wheel to raise needle
to its highest position. Loosen the
needle clamp screw just enough
to remove needle. A small
screwdriver may be helpful.
2. With flat side of needle to the right
(same side as needle clamp
screw), insert new needle up into
the clamp as far as it will go.
3. Re-tighten the needle clamp.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BOBBIN CASE REPLACEMENT
A special feature of the QuikStitch is the anti-thread jamming bobbin case.
The bobbin case is held in place by a positioning plate which is designed to
flex slightly to allow the bobbin case to move back and forth freely, about 1/16”.
In the event that the bobbin case becomes displaced and does not move freely
or pops out completely, follow the three easy steps below.
STEP 1:
Remove bobbin from bobbin case.
If bobbin case has popped out, put
back in position as follows: Place
bobbin case under position plate so
that screw head is under notch in
position plate. Then, slide the
bobbin case around until the metal
bracket sits between 2 o’clock and 4
o’clock positions. Proceed to step 2.
STEP 2:
Use left index finder to pull bobbin
case toward the right and up, until
lower half of metal bracket touches
the angled edge of the position plate.
Rotate the hand wheel until the
bobbin case rests in its correct
position. Proceed to step 3.
STEP 3:
Check bobbin case for proper
positioning. The screw head should
line up with the seam in the plastic
casing of the machine.
From side view, the top of the bobbin
case will be level with (or slightly
above) the position plate.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PERFORMANCE CHECKLIST
When sewing difficulties occur, refer back to this manual to make sure
that you are correctly following the instructions. If you are still having a
problem, the reminders below may help you solve the problem.
Needle does not move
ꢀꢁ Is machine connected to electrical
supply?
†ꢁ Is thread correctly lead around
bobbin winder tension disc?
Upper thread breaks
ꢀꢁ Is foot pedal connected?
†ꢁ Is machine properly threaded?
ꢀꢁ Is bobbin case displaced (pg.17)? †ꢁ Is thread freely unwinding from
spool?
Needle moves, but stitch is not
formed
†ꢁ Is needle in backwards?
†ꢁ Is needle defective?
†ꢁ Is needle size correct for thread?
†ꢁ Is upper thread tension too tight?
†ꢁ Is bobbin case properly inserted
(pg. 17)?
†ꢁ Is needle fully inserted into needle †ꢁ Is bobbin rim free of nicks?
clamp?
†ꢁ Are bobbin and needle correctly
threaded?
†ꢁ Is bobbin correctly inserted into
bobbin case?
Lower thread breaks
†ꢁ Is bobbin correctly wound?
†ꢁ Is bobbin correctly inserted into
bobbin case?
†ꢁ Is bobbin case correctly threaded?
†ꢁ Is bobbin case properly inserted
(pg. 17)?
Needle breaks
†ꢁ Is needle straight and sharp?
†ꢁ Is needle correct size?
†ꢁ Is needle fully inserted into needle Skipped stitches
clamp?
†ꢁ Is machine properly threaded?
†ꢁ Is fabric firmly held down?
†ꢁ Is needle correct size?
†ꢁ Is needle straight and sharp?
Bobbin winding difficulties
†ꢁ Is thread unwinding freely from
spool?
†ꢁ Is bobbin winder engaged?
†ꢁ Is thread end securely held at
start of wind?
Fabric does not move properly
under presser foot
†ꢁ Is presser foot lowered?
†ꢁ Is stitch length correctly set?
QUESTIONS?
If you have questions about any aspect of threading or sewing with the
QUIKSTITCH call:
Customer Support
Contact our Customer Support Team at Top Innovations, Inc. at (800) 711-
18
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Top Innovations, Inc. will repair or replace, at its
option, without charge to the consumer any SEW PRO£
product that fails due to a defect in material or
workmanship within 90 days following the initial
consumer purchase. This warranty does not cover
damage caused by commercial use, misuse, alteration,
or modification.
Performance of any obligation under this warranty may be
obtained by returning the warranted product, freight prepaid, with dated
proof of the purchase to:
TOP INNOVATIONS, INC.
Warranty Service Department
400 NW Platte Valley Drive
Riverside, MO 64150
If you have any questions about coverage under
this warranty, you may contact the Warranty Service
Department by telephone at 800-711-6617 or email:
This warranty gives you specific legal rights, and
you may also have others rights which vary from state to
state.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in China
Top Innovations, Inc.
400 NW Platte Valley Drive • Riverside, MO 64150
(800) 711-6617 (816) 584-9700 Fax: (816) 584-9066
20
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT!
INSTRUCTION MANUAL SUPPLEMENT
"THREADING THE MACHINE"
Needle
Threader
The purpose of this insert is to supplement the information given in the "Threading
the Machine" section on pages 10 & 11 of the instruction manual. Specifically, it
is meant to clarify steps 3 & 4 by illustrating the necessary procedures in further
detail. Follow the steps below, in combination with the information given in the
instruction manual, to properly thread the machine.
NOTE: Refer to the illustrations on the other side of this sheet for assistance in
completing the following steps.
1) Feed the thread around the Guide Bar located at the 3 o'clock position on the
Disc Thread Guide (FIGURE 1).
3 o'clock
Guide
Bar
9 o'clock
Guide
Bar
2) Insert the Needle Threader down through the Guide Bar that is located at the
9 o'clock position on the Disc Thread Guide (FIGURE 2).
3) Feed the slack end of the thread through the Needle Threader (FIGURE 3).
FIGURE 1
FIGURE 2
4) Pull Needle Threader (with thread inserted) back up through the Guide Bar
(FIGURE 4).
9 o'clock
Position
Guide
Bar
Disc Thread Guide
LONG
STITCH
SHORT
STITCH
TM
UIK TITCH
S
Q
3 o'clock
Position
Guide
Bar
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 3
FIGURE 4
|