User Manual
Phaser® 360
Color Printer
First printing May 1998
070-9922-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser® 360 Printer Warranty
Tektronix warrants that the Phaser 360 printer will be free from defects in materials and workmanship for a
period of one (1) year from the date of shipment. If this product proves defective during the warranty period,
Tektronix, at its option, will either repair the defective product on-site or by means of telephone support without
charge for parts and labor, or provide a replacement in exchange for the defective product.
In order to obtain service under the product warranty, Customer must notify Tektronix or its authorized
representative of the defect before the expiration of the warranty period and make suitable arrangements for the
performance of service. Tektronix or its authorized representative will provide such service at the CustomerÕs
site, if required, without charge during the warranty period, if the product is located in a normal on-site service
area. Outside the U.S., a description of the normal on-site service area can be obtained from the Local Tektronix
Subsidiary or Authorized Tektronix Distributor.
The maintenance tray in this product will be free from defects in materials and workmanship for a period of
ninety (90) days from the date of shipment or six (6) months where longer periods are required by law. If the
maintenance tray proves defective during the warranty period, Tektronix, at its option, will either repair the
defective product without charge for parts and labor, or provide a replacement in exchange for the defective
product. This 90 day warranty applies only to maintenance trays returned to the designated Tektronix depot.
For trays returned to other locations, Customer will be assessed an applicable service charge. The preceding
limitation shall not apply within the European Economic Area, where trays may be returned for warranty
service to the nearest designated service depot regardless of the place of purchase.
This warranty shall not apply to any defect, failure, or damage caused by improper use or improper or
inadequate maintenance and care. Tektronix shall not be obligated to furnish service under this warranty:
a. to repair damage resulting from attempts by personnel other than Tektronix representatives to
install, repair, or service the product;
b. to repair damage resulting from improper use or connection to incompatible equipment;
c. to repair any damage or malfunction caused by the use of non-Tektronix supplies or consumables;
d. to repair a product that has been modiÞed or integrated with other products when the effect of such
modiÞcation or integration increases the time or difÞculty of servicing the product;
e. to repair damage or malfunction resulting from failure to perform user maintenance and cleaning at
the frequency and as prescribed in the user manual; or
f. to repair this product after the limit of its duty cycle of 50,000 pages per month has been reached. All
service thereafter shall be billed on a time and material basis.
THE ABOVE WARRANTIES ARE GIVEN BY TEKTRONIX WITH RESPECT TO THIS PRODUCT IN LIEU OF
ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
TEKTRONIX' RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX
AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS
ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
WARRANTY 2(g)
Download from Www.Somanuals.com. All Manuals Search And Download.
Users safety summary
Terms in manual:
CAUTION Conditions that can result in damage to the product.
WARNING Conditions that can result in personal injury or loss of life.
Power source: Do not apply more than 250 volts RMS between the supply conductors or between either supply
conductor and ground. Use only the speciÞed power cord and connector. Refer to a qualiÞed service technician
for changes to the cord or connector.
Operation of product: Avoid electric shock by contacting a qualiÞed service technician to replace fuses inside the
product. Do not operate without the covers and panels properly installed. Do not operate in an atmosphere of
explosive gases.
WARNING Turning the power off using the On/Off switch does not de-energize the
printer. You must remove the power cord to disconnect the printer from the
mains. Keep the power cord accessible for removal in case of an emergency.
Safety instructions: Read all installation instructions carefully before you plug the product into a power source.
Terms on product: CAUTION A personal injury hazard exists that may not be apparent. For example, a
panel may cover the hazardous area. Also applies to a hazard to property
including the product itself.
DANGER
A personal injury hazard exists in the area where you see the sign.
Care of product: Disconnect the power plug by pulling the plug, not the cord. Disconnect the power plug if the
power cord or plug is frayed or otherwise damaged, if you spill anything into the case, if product is exposed to
any excess moisture, if product is dropped or damaged, if you suspect that the product needs servicing or repair,
and whenever you clean the product.
Ground the product: Plug the three-wire power cord (with grounding prong) into grounded AC outlets only. If
necessary, contact a licensed electrician to install a properly grounded outlet.
Symbols as marked on product:
DANGER high voltage:
Protective ground (earth) terminal:
Use caution. Refer to the manual(s) for information:
!
WARNING: If the product loses the ground connection, usage of knobs and controls (and other conductive parts)
can cause an electrical shock. Electrical product may be hazardous if misused.
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer ports 2-18
Connecting to a network 2-19
Connecting a PC or UNIX workstation to the parallel port 2-20
Connecting to a Macintosh 2-21
Turning on the printer 2-21
Front panel display and controls 2-22
Letting the printer warm up 2-23
Selecting a language for the front panel 2-24
Printing a Configuration Page 2-25
Tips for optimum printing performance 2-26
User Manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing printer software for Windows NT 3.51 3-11
Media trays 4-8
Media tray settings 4-9
Changing the default media tray setting 4-10
Printing letterhead 4-11
Printing labels 4-12
Printing transparencies 4-13
Printing transparencies from the transparency tray 4-13
Printing transparencies from the standard paper tray 4-14
Transparency quality tips 4-15
vi
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing from MS-DOS 4-34
5
Adjusting the color of your prints 5-2
TekColor correction descriptions 5-3
Printing and using the color sampler charts 5-6
Tips for working with color 5-7
Special considerations 5-8
Using the Quick Collate option 5-9
Previewing with Check Print 5-10
Using Image Smoothing 5-11
Printer languages 5-12
User Manual
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Using the Front Panel
Moving or shipping your printer 7-2
Adding ink 7-6
Ink handling tips 7-7
Emptying the waste liner 7-8
Replacing the maintenance tray 7-11
Cleaning the printer 7-14
If the printer has frequent media jams 7-14
If prints have light stripes or smears 7-15
The Cleaning Page 7-16
Cleaning supplies 7-18
viii
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the printerÕs language mode 8-25
PostScript printing errors 8-26
Using a PostScript error handler 8-27
Fixing timeout problems in Windows 8-28
Printed colors are not what you expected 8-31
Printing PANTONE Colors 8-32
Blue colors look too purple 8-32
Sharing the printer on a network 8-33
Prints do not reflect your settings 8-33
If the Apple Printer Utility does not work 8-33
User Manual
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing your printer 10-1
Media trays 10-4
Memory upgrade 10-5
Canadian EMC (Electromagnetic Compatibility)
regulatory standards 11-2
FCC Class B warning (for 115 VAC equipment) 11-3
Material Safety Data Sheets 11-3
MSDS for ColorStix ink sticks 11-4
MSDS for silicone oil (drum fluid) 11-6
Specifications 11-8
Safety and emissions 11-10
Index
x
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
1
About Your Printer
The Tektronix Phaser¨ 360 Color Printer is a fast, reliable, economical, and
easy-to-use printer that produces brilliant, high-quality color prints on plain
paper. It is compatible with the leading network protocols, operating
systems, and software applications, so everyone in your workgroup can use
it. Optional accessories and upgrades let you customize the printer to suit
your current needs and to expand its capabilities in the future.
The Phaser 360 Color Printer
9922-01
User Manual
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
1
About Your Printer
Features of your new printer
■ Fast Color. Quick color prints on paper at 6 pages per minute (ppm) and
Image quality and speed
transparencies at 5.5 ppm.
■ Standard. 300 x 300 dots per inch (dpi) for normal printing on paper at 4 ppm.
Recommended for overhead transparencies — produces vibrant, saturated prints at
2 ppm.
■ Enhanced. 800 x 450 dpi for the best text and image quality on paper (2 ppm). Use
for transparencies (at 600 x 300 dpi) with very fine detail.
■ Copier paper
Media (letter or A4-size)
■ Recycled paper
■ Bond
■ Letterhead
■ Labels (full-sheet, peel-off)
■ Card stock, up to 220 g/m2 (80 lb.)
■ Tektronix transparencies
■ Simultaneously supports PCs, Macintosh computers, and UNIX and OpenVMS
workstations, and automatically senses and switches between ports and protocols as
necessary.
Workgroup support
■ Includes 10BaseT Ethernet connection (supports NetWare, EtherTalk, TCP/IP,
Telnet, FTP, and HTTP). Optional network interfaces available.
■ 24 Mbytes, upgradeable to 48 Mbytes.
Memory
Fonts
■ 164 resident typefaces
■ Supports Adobe Type 1 and Type 3, TrueType, PCL5, and others
The printer’s Automatic mode optimizes color quality for text, graphics, and scanned
images on each page. Other color corrections let you adjust the color for special
needs:
Color matching:
TekColor™ Dynamic
Color Correction
■ Enhance the brightness of transparencies (Vivid Color).
■ Simulate the colors on the computer screen (Simulate Display).
■ Match printing press standards (various selections available).
1-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
About Your Printer
1
With the printer’s built-in PhaserLink™ software, you can use your web browser for a
variety of tasks, including the following:
Printer control through
your web browser
■ Avoid down time by automatically receiving email when ink is low, paper needs
loading, or other maintenance is required.
■ View the status of print jobs.
■ Get data on printer usage.
■ Configure the printer.
■ Create a local link to your own web site help pages.
■ Lower PaperTray Assembly. Adds 625-sheet paper capacity for convenience and
versatility. Use with the upper transparency tray to avoid having to reload media or
switch media trays.
Options and accessories
■ Transparency tray. Recommended for transparency printing — 175-sheet capacity.
Use with Tektronix transparencies for best transparency printing.
¨
■ PhaserShare network cards. 100BaseTx Ethernet, Token Ring, and LocalTalk
network interfaces are available.
■ Memory upgrade. Upgrade to 48 MBytes for even faster image processing and
throughput.
■ External hard drive. For collation and additional font storage. Mounts conveniently
on the back of the printer.
Visit the Tektronix Color Printer web site at http://www.tek.com/Color_Printers/ for
more information about your printer, including the following:
On-line support
■ Updated user documentation
■ Downloadable utility files
■ Tektronix dealers in your area
■ Technical support
Note
In addition to this manual, your printer is shipped with the
following important resources:
CD-ROM and diskettes Contains driver and utility Þles for installing and
operating your printer and additional user documentation.
Quick Reference Guide Contains at-a-glance instructions for basic printer
operations.
PhaserShare Networking System Administrator Manual and diskettes Contains
Þles and instructions for network installation and conÞguration, and
information on using PhaserLink software.
User Manual
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
1
About Your Printer
An illustrated guide to your printer
1
2
3
4
5
Front panel menu display and buttons
6
7
8
9
Transparency tray (optional)
Front cover
Top cover
Front cover release button
Manual-feed slot
Top cover release button
Transit restraint (printhead lock)
Paper tray
10 Lower Paper Tray Assembly (optional)
1
8
7
2
3
LETTER
A4
9
4
10
5
6
9922-125
1-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
About Your Printer
1
1
2
3
4
Maintenance tray
Waste liner
5
6
7
Ink loading bins
Ink sticks
Exit cover release button
Exit cover
Front cover (open)
6
5
4
3
2
1
7
9922-146
User Manual
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1
About Your Printer
1
External hard drive (optional), with bracket and cable
2
3
4
Back panel with interface ports and PhaserShare network card slot
On/Off switch
Power cord
1
4
Ethernet®
CV
XMT
lel
LNK
Second
Feeder
Ethernet
Network Adapter
2
PhaserShareTM
100
Series B
Ethernet Card
TX
Mbs
RESET
RCV
XMT
RX
TP
LINK
1
2
3
4
10Base2
10/100Base-TX
Service
Only
PS
PE
Parallel
LNK
Second
Feeder
Ethernet
Network Adapter
3
9922-147
1-6
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
About Your Printer
1
Printer parts and components
Consumables
ColorStix solid-ink sticks
Phaser 360 printer ColorStix¨ solid-ink sticks come in four colors: cyan,
matches the shape of the corresponding loading bin on top of the printer.
The printer holds up to three ink sticks of each color, and you can replace ink
sticks easily Ñ and without having to wait until the printer runs out of ink.
ColorStix ink sticks are clean, safe, and environmentally friendly.
Your printer is shipped with a starter ink pack containing one of each color
ink stick. Replace ink sticks when prompted by the printer.
Note
To ensure that your printer is always available for use, Tektronix
recommends that you immediately order and maintain a stock of
each color ink stick. See “Printer supplies” on page 10-2 for
ordering information.
Maintenance tray and waste liner
The maintenance tray is a replaceable tray that is used during the printerÕs
printing and cleaning operations. The blue plastic tray inserted in the
maintenance tray is the waste liner, which catches ink purged when the
printer runs through its cleaning cycle. Replace the maintenance tray when
a message at the printerÕs front panel indicates the tray is low, after about
12,500 prints. Empty the waste liner when prompted by the printer.
Note
To avoid printing delays, always keep an extra maintenance tray
available. See “Printer supplies” on page 10-2 for ordering
information.
User Manual
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
1
About Your Printer
Printer parts
Paper/transparency tray
The standard tray (for either letter- or A4-size media) shipped with the
printer accepts up to 200 sheets of common ofÞce paper, ranging from 60 to
120 g/m2 (16 to 32 lb.)., You can also load full-sheet peel-off labels or up to
50 sheets of transparencies or labels in the standard paper tray.
Manual feed slot
Use this slot to feed single sheets of paper, nonglossy cover stock Ñ up to
220 g/m2 (80 lb.) Ñ or transparencies.
Transit restraint
The transit restraint on the right side of the printer secures the printhead in
the printer. You must lock the transit restraint before moving or shipping the
printer and unlock the transit restraint before operating the printer.
Back panel
The On/Off switch, power plug, and interface ports are on the back of the
printer. The Phaser 360 printer has a built-in Ethernet connection, a SCSI
port for an external hard drive, a bidirectional parallel port, and an
expansion slot to support an optional Tektronix PhaserShare network card.
1-8
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
About Your Printer
1
Options and accessories
High-capacity transparency tray
Save time and effort by ordering a Tektronix high-capacity transparency tray
for transparency and label printing only. Transparency trays (letter- and
A4-size) hold up to 175 sheets (about three boxes) of transparencies and
100 sheets of labels. By adding a transparency tray and a Lower Paper Tray
Assembly, you can print on paper and transparencies without having to
leave your computer to swap trays.
Tektronix transparency media
To ensure reliable, high-quality transparency printing, use only Tektronix
standard or premium transparencies. Premium-grade transparencies,
indicated by a notched corner, provide superior print quality and enhanced
ink adhesion.
Lower Paper Tray Assembly
With a 625-sheet paper capacity, the Lower Paper Tray Assembly is
recommended for high-volume printing needs. Dual-tray printing is
especially convenient if you commonly print on different types of media.
For example, you can keep plain paper in the lower tray, and transparencies,
letterhead, or label media in the upper tray. The optional Lower Paper Tray
Assembly can be ordered for either letter- or A4-size paper.
Tektronix external hard disk
Add the Tektronix 2.1-Gbyte external hard disk to a Phaser 360 printer to
make your printer even more versatile. The following capabilities are added
with the installation of the Tektronix external hard drive:
■
Collating large jobs. The Quick Collate function collates large
print jobs quickly, performing this task faster than the collation
feature that may exist in your application.
User Manual
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
1
About Your Printer
■
■
Expanded job accounting. Allows you to keep records on up to
5000 print jobs. You can track usage rates and times, users, paper
consumption, duration of print jobs, and other important
information.
Font storage. Provides storage for additional downloadable fonts.
Refer to the printerÕs CD-ROM and the PhaserShare NetworkingSystem
Administrator Manual for more information.
1-10
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
2
Setting up the printer: at a glance
4. Unlock the transit restraint (page 2-7).
6. Load the ink sticks (page 2-10).
9. Connect the printer to your computer or network (page 2-18).
10. Connect the power cord and turn printer on (page 2-21).
11. Let the printer warm up (15 minutes) (page 2-23).
12. Select a language from the front panel display menu (page 2-24).
13. Print a ConÞguration Page (page 2-25).
14. Install the appropriate printer driver software (page 3-1).
User Manual
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
What you get with your printer
The following items are shipped with the printer. The optional Lower Paper
Tray Assembly, network cards, and Tektronix external hard disk are shipped
separately.
1. Quick-Start Installation guide
2. ColorStix ink starter pack
3. Package of Tektronix premium transparencies
4. Paper tray (letter- or A4-size)
5. Maintenance tray and waste liner
6. Cleaning kit
7. Power cord
8. Parallel cable adapter
9. Registration packet
10. Supplies sheet
11. License agreement
12. Phaser 360 Color Printer User Manual
13. Phaser 360 Color Printer Quick Reference Guide
14. Phaser 360 Printer CD-ROM, ATM (Adobe Type Manager)
CD-ROM, and diskettes (printer drivers and utility software)
15. PhaserShare Networking Administrator Manual and diskettes
2-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
Choosing a printer location
To ensure proper printer operation:
1. Install the printer on a ßat surface. The degree of tilt should be no
more than 3 degrees, approximately equivalent to lifting one side
of the printer 2 cm (0.75 in.) off a ßat surface.
2. Allow at least 5 cm (2 in.) clearance on each side of the printer for
proper ventilation and to prevent the printer from overheating.
Caution
Some of the printer’s internal parts may be damaged or the
printer may not operate properly if the printer isn’t adequately
ventilated. Avoid leaving loose paper or packing materials
next to the vent on the right side of the printer; they may
adhere to the vent, causing the printer to overheat.
Removing the packing material
Remove the plastic bag and packing materials surrounding the printer.
Note
Save all boxes and packing material in case you need to ship the
printer later.
Registering the printer
Your product registration card is contained in the Register Now! envelope
that is shipped with your printer. Fill out the appropriate card (U.S. or
international versions) and mail it. By registering your printer with
Tektronix, you validate the product warranty and ensure that you will
receive information about upgrades, service, and accessories. You can also
register on-line at the Tektronix web site:
http://www.tek.com./Color_Printers/
User Manual
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
Installing the Lower Paper Tray Assembly (optional)
Caution
If you are adding a Lower Paper Tray Assembly to a printer
that is already in service, let the printer cool down for at least
30 minutes before you move it to allow sufficient time for the
ink to solidify. Then remove the maintenance tray, and turn off
and unplug the printer.
1. Unpack the Lower Paper Tray Assembly.
2. Remove the tray from the Lower Paper Tray Assembly. Remove
the shipping block from the tray and replace the tray in the
assembly. Refer to page 2-15 for paper-loading instructions.
9922-04
3. Place the Lower Paper Tray Assembly where you will install the
printer.
Note
To ensure proper printer operation, install the printer and Lower
Paper Tray Assembly on a flat surface having no more than
3 degrees of tilt. This is approximately equivalent to lifting one
side of the printer 2 cm (0.75 in.) off a flat surface.
2-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
4. Place the printer on top of the Lower Paper Tray Assembly.
9101-57
Warning The printer weighs about 32 kg (70 lb.). Do not attempt to lift
the printer without the assistance of another person.
5. Make sure that the left and right alignment pins Þt in the holes in
the base of the printer.
6. Plug the Lower Paper Tray Assembly cable into the printer.
6
5
9922-02
User Manual
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
already in service, reinsert the maintenance tray, plug the printer
back in, and turn the printer on.
Warning The printer is not permanently attached to the Lower Paper
Tray Assembly. When moving the printer, first disconnect it
from the Lower Paper Tray Assembly and then move each unit
separately. Moving the printer incorrectly may cause damage
or personal injury.
■
For ordering information, refer to ÒLower Paper Tray AssemblyÓ
on page 10-4.
2-6
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
Unlocking the transit restraint
1. Insert a wide ßat-blade screwdriver into the slot of the transit
restraint lock, located on the right side of the printer.
2. While pushing inward with slight pressure, turn the lock button
counterclockwise until it springs out ßush with the side of the
printer.
2
1
9922-03
Caution
If you move or ship the printer, be sure to lock the transit
restraint to protect the printhead from damage. Always turn
the printer power off using the On/Off switch before locking or
unlocking the transit restraint. Refer to “Moving or shipping
your printer” on page 7-2 for more information.
User Manual
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
Installing the maintenance tray
The disposable maintenance tray (labeled with a blue ÒBÓ) shipped with
your printer must be installed before printing is possible. For more details
on the maintenance tray, see ÒEmptying the waste linerÓ on page 7-8 and
ÒReplacing the maintenance trayÓ on page 7-11.
Note
To avoid printing delays, always keep an extra maintenance tray
available for use in the printer. For ordering information, see
“Printer supplies” on page 10-2.
1. Open the maintenance tray shipping box and remove the
maintenance tray.
2. Remove the packing materials from the maintenance tray. Retain
the plastic bag for disposal of the used maintenance tray later.
3. Open the front cover.
9922-65
2-8
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
4. Install the maintenance tray by sliding it into the printer. Make
sure that the tray slides in straight on both sides.
9922-38
5. Using both thumbs, push the tray in Þrmly until it latches.
9922-150
6. Close the front cover.
If you move or ship the printer, be sure to remove the
Caution
maintenance tray to protect the printer from damage. Refer to
“Moving or shipping your printer” on page 7-2 for more
information.
User Manual
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
Loading the ink sticks
Your printer is shipped with a sampler containing one of each of the
ColorStix ink sticks (black, cyan, magenta, and yellow). Load the ink sticks
before you begin printing. For more details on color ink sticks, see ÒAdding
inkÓ on page 7-6.
Note
To avoid printing delays, maintain a stock of each color ink stick.
For ordering information, see “Printer supplies” on page 10-2.
1. Open the top cover. Note the color-coded label and the different
shapes of the slots of the ink-loading bin. Each ink stick color has
a unique shape.
2. Drop the ink stick of the correct color and shape into each
ink-loading bin, with the narrow (tapered) edge down.
1
2
9922-21
3. After loading all four ink sticks, close the top cover.
2-10
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
Loading the media trays
Your printer is shipped with a single media tray (letter- or A4-size) that
accepts common ofÞce paper and letterhead, transparencies, and labels. If
you frequently print on different types of media, you may want to obtain a
tray for each type of media you use. For transparency printing, the optional
transparency tray is recommended.
■
For more detail about the types of media you can use with your
printer and media tray options, refer to ÒAcceptable media sizes,
types, and weightÓ on page 4-6.
Loading paper and transparency trays
1. Remove the paper tray from the printer. Take out the shipping
insert.
9922-139
User Manual
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
2. To load paper:
a. First fan the paper to release sheets that are stuck together.
b. Load up to 200 sheets of common ofÞce paper (slightly less
than one-half ream). A label on the inside of the paper tray
indicates the trayÕs maximum capacity.
c. Set the switch on the side of the tray to Paper.
9922-05
2-12
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
3. To load transparencies:
a. Handle transparencies by the edges and with both hands to
avoid Þngerprints and creases, which can result in poor print
quality.
b. Load up to 50 transparencies in the standard paper tray (the
bottom line on the Þll label) and 175 sheets (about three boxes)
in the transparency tray (the Þll line indicates the maximum
capacity).
c. Set the switch on the side of the tray to Transparency..
d. Load Tektronix premium transparencies with the notch in the
back, right corner of the tray. Load standard Tektronix
transparencies in any orientation.
9922-06
User Manual
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
4. Make sure that the media Þts snugly against the inside front wall
of the tray.
4
9922-07
5. Insert the loaded media tray into the printer.
2-14
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
Loading the optional Lower Paper Tray Assembly
The Lower Paper Tray Assembly holds up to 625 sheets (approximately one
and one-quarter ream) of 90 g/m2 (24 lb.) paper. A label on the inside of the
tray provides a Þll line to indicate the trayÕs maximum paper capacity.
■
For more information on the Lower Paper Tray Assembly, see
ÒMedia traysÓ on page 4-8 and ÒLower Paper Tray AssemblyÓ on
page 10-4.
Note
The Lower Paper Tray Assembly accepts paper media only; it
should not be used with transparencies or label stock.
1. Remove the paper tray from the Lower Paper Tray Assembly.
9922-74
User Manual
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
2. Select one-half of a ream (250 sheets or less) of paper at a time.
3. Prior to loading paper in the Lower Paper Tray Assembly, fan the
paper stack to release sheets that are stuck together.
2
3
1⁄2
9101-56
4. Load the Þrst stack of paper in the tray. Make sure that the paper
Þts snugly against the slanted back wall of the tray.
5. Load the second stack of paper. Make sure that the paper Þts ßat
in the tray. Load the Þnal stack (one-quarter ream) and make sure
that the paper is still ßat in the tray.
1
⁄2
+
1
⁄2
!
9101-55
6. Insert the paper tray into the Lower Paper Tray Assembly.
2-16
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
Connecting an external hard disk (optional)
The Phaser 360 printer has a SCSI (Small Computer System Interface,
pronounced ÒscuzzyÓ) port on the rear panel. The SCSI speciÞcation is an
industry standard for connecting computer peripherals. Use this port only
for connecting an external hard disk to the printer. You can connect one or
collation. Tektronix offers a 2.1-Gbyte hard disk that mounts conveniently on
the rear of the printer.
memory with the Phaser 360 printer. For example, SCSI hard disks that
work with an Apple LaserWriter will work with a Phaser 360 printer.
Contact your computer or printer dealer for information.
■
■
■
See the printerÕs CD-ROM for complete directions on installing an
external hard disk and downloading fonts.
Refer to ÒUsing the Quick Collate optionÓ on page 5-9 for details
on collating multipage jobs.
See ÒTektronix external hard diskÓ on page 10-5 for ordering
information. Refer to ÒInterface cables and adaptersÓ on page 10-7
for information on ordering SCSI cables.
User Manual
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
Connecting the printer
The printer can be connected to networks and single workstations. Refer to
the PhaserShare Networking System Administrator Manual for more
information on installing and conÞguring the printer on a network.
Printer ports
The Phaser 360 printer has the following ports:
1. 10BaseT Ethernet connection
2. SCSI port for an external hard drive
3. parallel port
4. slot for an optional network card (shown with card installed)
P
haserShareTM
eries
thernet
1
M
00
bs
S
B
T
X
RESET
E
C
ard
RCV
XMT
R
X
T
P
LINK
1
2
3
4
1
0
/1
0
0
B
a
s
e
-T
X
1
0
B
a
s
e
2
Service
Only
PS
PE
Parallel
LNK Ethernet
Second
Feeder
Network Adapter
1
2
PhaserShareTM
Series B
Ethernet Card
100
Mbs
TX
RX
RESET
RCV
XMT
TP
LINK
1
2
3
4
10Base2
10/100Base-TX
Service
Only
PS
PE
Parallel
LNK
Second
Feeder
Ethernet
Network Adapter
4
3
9922-102
2-18
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
Connecting to a network
The Phaser 360 printer has a built-in 10BaseT Ethernet port for network
connectivity. An expansion slot is provided for optional Tektronix
PhaserShare network cards for 100BaseTx Ethernet (includes connection for
10Base2), Token Ring, or LocalTalk connections.
P
haserShareTM
eries
thernet
1
M
00
bs
S
B
T
X
RESET
E
C
ard
RCV
XMT
R
X
T
P
LINK
1
2
3
4
1
0
/1
0
0
B
a
s
e
-T
X
1
0
B
a
s
e
2
Service
Only
PS
PE
Parallel
LNK Ethernet
Second
Feeder
Network Adapter
PhaserShareTM
Series B
Ethernet Card
100
Mbs
TX
RX
RESET
RCV
XMT
TP
LINK
1
2
3
4
10Base2
10/100Base-TX
Service
Only
PS
PE
Parallel
LNK
Second
Feeder
Ethernet
Network Adapter
9922-127
■
■
For information on installing and conÞguring your printer on a
network, refer to the PhaserShare Networking System Administrator
Manual shipped with your printer.
For ordering information, refer to ÒPhaserShare network cardsÓ on
page 10-3.
User Manual
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
Connecting a PC or UNIX workstation to the parallel port
The printer supports a bidirectional parallel port. Connect your computer to
the printerÕs parallel port with a standard parallel cable and the adapter
shipped with your printer. Make all connections before you turn on the
printer.
Parallel
P
haserShareTM
eries
thernet
100
Mbs
S
B
T
X
RESET
E
C
ard
RCV
XMT
RX
TP
LINK
1
2
3
4
10/100B
a
se-T
X
10B
a
se
2
Service
Only
PS
PE
Parallel
LNK
Second
Feeder
Ethernet
Network Adapter
9922-08
■
■
If large Þles do not print, you may need to reset the printerÕs
timeouts. Refer to ÒFixing timeout problems in WindowsÓ on
page 8-28.
Refer to the printerÕs CD-ROM for information on bidirectional
status reporting and parallel port pin signals.
2-20
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
Connecting to a Macintosh
Connect Macintosh computers on a network through the built-in Ethernet
interface. An optional LocalTalk network card is available.
■
Refer to the PhaserShare Networking System Administrator Manual
for installation and conÞguration procedures.
■
See ÒPhaserShare network cardsÓ on page 10-3 for ordering
information.
Turning on the printer
1. Plug the power cord into the printer and into a grounded outlet.
2. Turn on the printer.
To ensure optimum printing performance and best ink economy,
Note
always leave the printer turned on. The printer automatically
switches into a standby mode during periods of infrequent use to
reduce power consumption.
2
RESET
isk
D
PE
I
S
C
S
Second
Feeder
PS
Parallel
PHASER 3r
RCV
r
et®
ern
th
E
Net
1
9922-10
User Manual
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
Front panel display and controls
When the printer is turned on, the front panel display is lighted. Watch the
front panel display for instructions as you Þnish the set-up procedure.
Status messages, such as Warming Up or Ready,appear on the top line
of the display. Other messages, such as Info, Clean,and Menuappear
on the lower line of the display; these identify a function for the
corresponding button located below the message. For example, pressing the
button located under the word Menudisplays the printerÕs menus.
Info
Clean
Menu
Exit
9922-68
■
Refer to ÒUsing the Front PanelÓ on page 6-1 for a complete
description of front panel controls and menus.
■
■
See also ÒFront panel error messagesÓ on page 8-2.
System administrators may choose to modify or limit access to
front panel menus. See the printerÕs CD-ROM for instructions on
enabling and disabling the front panel menu.
2-22
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
Letting the printer warm up
After you have installed the maintenance tray and the media tray, allow the
printer about 15 minutes to warm up and perform self-tests. As the printer
warms up, note the following:
■
Front panel display. When you Þrst turn on the printer, two
indicator lights come on, the power light and the error light.
During the warm-up cycle, the top power indicator blinks on and
off, the error light goes out, and the front panel displays a series of
ÒWarming upÓ messages. A percentage value is shown to indicate
the progress of the warm-up cycle. The cycle is complete when the
front panel displays 100%, then Ready.
■
■
■
noises; these are normal and are not an indication of problems
with the printer.
Cleaning Page. The printer outputs a color-striped ÒCleaning
PageÓ as part of its self-maintenance. Refer to page 7-16 for more
information on the Cleaning Page.
Startup Page. The printer outputs a page that lists your printerÕs
name and serial number, the number of pages printed, installed
interface ports, and other information. This Startup Page
automatically prints whenever you turn on your printer. To turn
off the Startup Page, refer to page 6-6.
■ Readymessage. The front panel displays Readyor the printerÕs
name when the printer is available for printing.
User Manual
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
Selecting a language for the front panel
Messages that appear in the front panel window are in English by default.
You can skip this step if you want the front panel to display messages in
English. To change the language to Spanish, French, German, Italian, or
Japanese, follow these steps. (If Chinese or Korean font SIMMs are installed,
the front panel will display in English; output will be in the speciÞed
language.)
1. When the printer is on and Readyor the printerÕs name appears
in the front panel, press the Menubutton. The printer displays the
Þrst selection in the menu:
Help Pages
<---- ----> Menu
2. Using the left (<----)or right (---->)arrow buttons, scroll
through the selections until the following message appears:
Language
<---- ----> Menu
3. Press the Menubutton to access language selections. The printer
displays the following message:
Language:English*
<---- ----> OK
where the asterisk (*) indicates the currently selected language.
4. Using the left or right arrow buttons, scroll through the language
selections until you reach the appropriate setting.
5. To conÞrm your language selection, press the OKbutton.
6. Press the Exit button until the printer displays the Ready
message.
2-24
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Set Up
2
Printing a Configuration Page
After the printer is installed, print the ConÞguration Page. This page lists
important information about your printer, including the serial number,
printer ID, amount of installed memory, and network protocols enabled.
Use this page as a resource for reconÞguring your printer or when
contacting Tektronix Customer Support.
To print the ConÞguration Page:
1. When the printer is on and the Readymessage appears, press the
Menubutton. You see this message:
Help Pages
<--- ---> Menu
2. Press the Menu button. The following message appears:
Menu Map
<--- ---> Print
3. Using the left (<---) or Press the right (--->) arrowbutton.s,
scroll through the selections until you see tThis message appears:
Configuration Page
<--- ---> Print
4. To print the ConÞguration Page, press the Printbutton.
User Manual
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Set Up
Tips for optimum printing performance
■
Always leave the printer on. Whenever you turn off and restart
the printer, it performs a cleaning routine that consumes ink. To
ensure optimum printing performance and best ink economy,
leave the printer turned on overnight and during weekends.
When the printer sits idle, it automatically switches to a standby
mode that reduces energy consumption but keeps the printer
ready to use. Pressing a front panel button, opening a cover, or
sending a print job then ÒwakesÓ the printer.
■
Use Tektronix supplies. Use the Tektronix transparency tray and
transparency media (standard or premium) for reliable,
high-quality transparency printing. The transparency tray holds
up to 175 transparency sheets, saving you from frequent
reloadings and interrupted print jobs. And, with the optional
Lower Paper Tray Assembly, you can automatically switch
■
■
Do not print on both sides of the media. Printing on both sides
of a sheet of paper or transparency Þlm causes ink to be offset onto
the printerÕs internal paper path, which will require you to clean
the printer.
Use the correct type, size, and weight of media. Use the
appropriate media tray and make the appropriate media selection
from the printer driver. Load the media correctly, and do not
overload the trays. The Tektronix transparency tray and
transparencies are recommended for transparency printing. Refer
to ÒAcceptable media sizes, types, and weightÓ on page 4-6 for
more information.
2-26
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
3
Installing Printer
Software
Overview
Packaged with your printer is a CD-ROM and a set of diskettes that contain
that automatically install the printerÕs software onto your computerÕs hard
sampler charts, and utility Þles. You can select a standard installation (Easy
Note
ATM (Adobe Type Manager) software is available on a separate
CD-ROM included with your printer.
Refer to the following pages for platform-speciÞc instructions:
■
■
■
ÒPC/Windows softwareÓ on page 3-2.
ÒMac OS softwareÓ on page 3-16.
ÒUNIX workstation softwareÓ on page 3-23.
User Manual
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
PC/Windows software
Refer to the following instructions depending on which version of Windows
you are using:
■
■
■
■
ÒInstalling printer software for Windows 95Ó on page 3-3
ÒInstalling printer software for Windows NT 4.0Ó on page 3-6
ÒInstalling printer software for Windows NT 3.51Ó on page 3-10
ÒInstalling printer software for Windows 3.1Ó on page 3-13
3-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Printer Software
3
Installing printer software for Windows 95
Note
This procedure installs the AdobePS 4 printer driver. If you are
installing from diskettes, you may need more than one diskette
depending on your Windows system. Keep all of the printer’s
diskettes handy during the installation, and insert each diskette
when you are prompted by the installation program.
1. Insert either the printerÕs CD-ROM or the Phaser 360 Color
Printer Installer for Windows Disk 1 into the appropriate drive on
your computer.
2. Click the Start icon in the taskbar, and select Run.
3. Type in the drive for the CD-ROM or diskette, type SETUP and
click OK.
4. In the Installer, click Next until the Select Installation Type dialog
box appears.
5. Select either Easy Installation or Custom Installation, and
click Next. When you Þnish with the Easy or Custom
instructions, continue with Step 6 on page 3-5.
Easy Installation
a. The following files are copied to your computer’s hard disk:
■ QuarkXPress PDF
Installs an application-specific printer description file, if the application is found.
■ PhaserPrint Plug-in for Photoshop
Installs an application-specific plug-in.
■ Samplers
Installs color sampler charts and a fonts sampler.
b. In the Choose Destination Directory dialog box, select the location for installing the PhaserPrint plug-in.
c. Click Next.
Files are copied to your computer’s hard disk.
User Manual
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
Custom Installation
a. In the Driver Installation dialog box, select from the following options, then click Next to continue.
■ Drivers/PPDs
Installs driver files and printer description files.
■ QuarkXPress PDF
Installs an application-specific printer description file.
■ PhaserPrint Plug-in for Photoshop
Installs an application-specific plug-in.
b. If you checked the PhaserPrint plug-in option, now select the location for installing the plug-in in the Choose
Destination Directory dialog box. Click Next to continue.
c. In the Custom Install: Select Utilities dialog box, select from the following options, then click Next to continue.
■ Printer Utilities
Installs utility files for selecting printer features.
■ Network Utilities
Installs utility files for using the printer on a network.
■ Samplers
Installs color sampler charts and a fonts sampler.
Use the default Destination Directory or click Browse.
Files are copied to your computer’s hard disk.
d. If the LPT.VXD update dialog box appears, clickYes or No to continue. Updating this file is recommended.
e. The PhaserShare Installation dialog box appears. PhaserShare software consists of two applications for use on
Novell NetWare networks: a printer status application for users and a printer administration application for system
administrators. Make selections from the following options, then click Next to continue:
■ Both PhaserShare Status Monitor and Administrator
■ PhaserShare Status Monitor
■ PhaserShare Administrator
■ Do Not Install PhaserShare
f. Select PhaserShare installation type, then click Next to continue:
■ Standard Install (automatically installs the choice you made in the previous dialog box)
■ Network Install (copies PhaserShare installation files to a network server)
g. If you selected the PhaserShare Network Install option, click Browse to select the drive for installing the
installation files. Click Next to continue. Click OK in the installation successful dialog box.
Files are copied to your computer’s hard disk or to a selected network destination.
Note: To use the PhaserShare software installer you copied to a network server, go to the location of the copied
files, and run SETUP.EXE. Follow the installation prompts to install PhaserShare software on local
NetWare-enabled workstations.
3-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Printer Software
3
6. The Finish Installation dialog box contains instructions for
completing the printer software setup; click Next. The Add
Printer Wizard program is automatically launched.
7. In the Add Printer Wizard, click Next in the opening dialog box.
8. Select your printerÕs connection, either Local Printer or
Network Printer, and click Next.
9. In the Manufacturers/Printers dialog box, click Have Disk.
10. Type in the drive for the CD-ROM or diskette, and click OK.
11. Select your Tektronix Phaser 360 printer, and click Next.
12. Select the port your printer is connected to, and click Next.
13. Enter a name for the printer, and select the Phaser 360 as the
default printer if desired, and click Next.
14. Decide if you want to print a test page, select Yes or No, and click
Finish.
15. In the Installation Completed dialog box, click Finish.
16. You may see a Restart Windows dialog box if the system needs to
be updated. Decide if you want to restart now or later, and
click OK.
Note
See the “Adobe PostScript Printer Driver User Guide” on the
printer’s CD-ROM (USERGUIDE.PDF) for detailed
information on the AdobePS 4 driver.
User Manual
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
Installing printer software for Windows NT 4.0
Note
If you are installing from diskettes, you may need more than one
diskette depending on your Windows system. Keep all of the
printer’s diskettes handy during the installation, and insert each
diskette when you are prompted by the installation program.
If you will be using a printer on a network, refer to your Windows NT
manual for instructions on installing network software, either Services for
Macintosh (AppleTalk) or TCP/IP print services (for TCP/IP; lpr print
services).
1. Insert either the printerÕs CD-ROM or the Phaser 360 Color
Printer Installer for Windows Disk 1 into the appropriate drive on
your computer.
2. Click the Start icon in the taskbar, and select Run.
3. Type in the drive for the CD-ROM or diskette, type SETUP, and
click OK.
4. In the Installer, click Next until the Select Installation Type dialog
box appears.
5. Select either Easy Installation or Custom Installation, and
click Next. When you Þnish with the Easy or Custom
instructions, continue with Step 6 on page 3-8.
Easy Installation
a. The following files are copied to your computer’s hard disk:
■ QuarkXPress PDF
Installs an application-specific printer description file, if the application is found.
■ PhaserPrint Plug-in for Photoshop
Installs an application-specific plug-in.
■ Samplers
Installs color sampler charts and a fonts sampler.
b. In the Choose Destination Directory dialog box, select the location for installing the PhaserPrint plug-in.
c. Click Next.
Files are copied to your computer’s hard disk.
3-6
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Printer Software
3
Custom Installation
a. In the Driver Installation dialog box, select from the following options, then click Next to continue.
■ Drivers/PPDs
Installs driver files and printer description files.
■ QuarkXPress PDF
Installs an application-specific printer description file.
■ PhaserPrint Plug-in for Photoshop
Installs an application-specific plug-in.
b. If you checked the PhaserPrint plug-in option, now select the location for installing the plug-in in the Choose
Destination Directory dialog box. Click Next to continue.
c. In the Custom Install: Select Utilities dialog box, select from the following options, then click Next to continue.
■ Printer Utilities
Installs utility files for selecting printer features.
■ Network Utilities
Installs utility files for using the printer on a network.
■ Samplers
Installs color sampler charts and a fonts sampler.
Use the default Destination Directory or click Browse.
Files are copied to your computer’s hard disk.
d. The PhaserShare Installation dialog box appears. PhaserShare software consists of two applications for use on
Novell NetWare networks: a printer status application for users and a printer administration application for system
administrators. Make selections from the following options, then click Next to continue:
■ Both PhaserShare Status Monitor and Administrator
■ PhaserShare Status Monitor
■ PhaserShare Administrator
■ Do Not Install PhaserShare
e. Select PhaserShare installation type, then click Next to continue:
■ Standard Install (automatically installs the choice you made in the previous dialog box)
■ Network Install (copies PhaserShare installation files to a network server)
f. If you selected the PhaserShare Network Install option, click Browse to select the drive for installing the
installation files. Click Next to continue. Click OK in the installation successful dialog box.
Files are copied to your computer’s hard disk or a selected network destination.
Note: To use the PhaserShare software installer you copied to a network server, go to the location of the copied
files, and run SETUP.EXE. Follow the installation prompts to install PhaserShare software on local NetWare-enabled
workstations.
User Manual
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
6. The Finish Installation dialog box contains instructions for
completing the printer software setup; click Next. The Add
Printer Wizard program is automatically launched.
7. In the Add Printer Wizard, click Next in the opening dialog box.
8. Select printer management, either My computer or
Network printer server, and click Next.
9. Select a local printer port, or follow these instructions for a
network port:
LPR port (for TCP/IP) setup instructions
a. Click the Add Port button.
AppleTalk port setup instructions
a. Click the Add Port button.
b. In the Printer Ports dialog box, under
b. In the Printer Ports dialog box, under Available Printer
Available Printer Ports, select LPR Port.
Ports, select AppleTalk Printing Devices.
c. Click the New Port button; the Add LPR
c. Click the New Port button.
compatible printer dialog box appears.
d. Under AppleTalk Printing Devices, double-click on the
d. For Name or address of host providing lpd,
type your printer’s IP address (or Host name if
known to the network).
appropriate zone (if there are multiple AppleTalk zones).
e. Select your Tektronix printer and click OK.
f. At the prompt: Do you want to capture this AppleTalk
Note: The printer’s IP address may be available
on the printer’s Configuration Page. If not, ask
your network administrator.
Printing Device?, click No.
Note: ClickingYes hides the printer from regular Macintosh
users, forcing them to use NT Server as a spooler, as long as
NT Server allows sharing of this printer.
e. For Name of printer or print queue on that
server, type in one of the following (use
uppercase letters):
g. Click OK.
h. In the Printer Ports dialog box, click the Close button to
■ PS for PostScript
■ AUTO for automatic selection
f. Click OK.
return to the Add Printer Wizard.
i. Click Next and continue with Step 10 below.
g. In the Printer Ports dialog box, click the Close
button to return to the Add Printer Wizard.
h. Click Next and continue with Step 10 below.
10. In the Manufacturers/Printers dialog box, click Have Disk.
11. Type in the drive for the CD-ROM or diskette, and click OK.
12. Select your Tektronix Phaser 360 printer, and click Next.
3-8
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Printer Software
3
13. Enter a name for the printer, and select the Phaser 360 as the
default printer if desired, and click Next.
14. Decide if you want to share the printer, Shared or Not shared, and
click Next.
If you are installing drivers for platforms other than Windows NT
4.0, for example Windows 95, a message appears during the
installation procedure asking for the location of printer Þles. If
you see this message, at the prompt, type in the CD-ROM drive
followed by \PPDS95NT.DVRTEKMSDRV, and click OK. Files are
copied to your computerÕs hard disk.
If you are installing drivers for Windows NT 3.51 for platforms
other than i386, click Browse to locate the appropriate
subdirectory under \PPDS95NT.DVRTEKMSDRV\WINNT351on
the printer's CD-ROM.
15. Decide if you want to print a test page, select Yes or No, and click
Finish.
16. In the Installation Completed dialog box, click Finish.
17. You may see a Restart Windows dialog box if the system needs to
be updated. Decide if you want to restart now or later, and
click OK.
User Manual
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
Installing printer software for Windows NT 3.51
Note
If you are installing from diskettes, you may need more than one
diskette depending on your Windows system. Keep all of the
printer’s diskettes handy during the installation, and insert each
diskette when you are prompted by the installation program.
If you will be using a printer on a network, refer to your Windows
NT manual for instructions on installing network software,
either Services for Macintosh (AppleTalk) or TCP/IP print
services (for TCP/IP; lpr print services).
1. Insert either the printerÕs CD-ROM or the Phaser 360 Color
Printer Installer for Windows Disk 1 into the appropriate drive on
your computer.
2. Select Run from the File menu.
3. Type in the drive for the CD-ROM or diskette, type SETUP and
click OK.
4. In the Installer, click Next until the Select Installation Type dialog
box appears.
5. Select either Easy Installation or Custom Installation, and
click Next. When you Þnish with the Easy or Custom
instructions, continue with Step 6 on page 3-12.
Easy Installation
a. The following files are copied to your computer’s hard disk:
■ QuarkXPress PDF
Installs an application-specific printer description file, if the application is found.
■ PhaserPrint Plug-in for Photoshop
Installs an application-specific plug-in.
■ Samplers
Installs color sampler charts and a fonts sampler.
b. In the Choose Destination Directory dialog box, select the location for installing the PhaserPrint plug-in.
c. Click Next.
Files are copied to your computer’s hard disk.
3-10
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Printer Software
3
Custom Installation
a. In the Driver Installation dialog box, select from the following options, then click Next to continue.
■ Drivers/PPDs
Installs driver files and printer description files.
■ QuarkXPress PDF
Installs an application-specific printer description file.
■ PhaserPrint Plug-in for Photoshop
Installs an application-specific plug-in.
b. If you checked the PhaserPrint plug-in option, now select the location for installing the plug-in in the Choose
Destination Directory dialog box. Click Next to continue.
c. In the Custom Install: Select Utilities dialog box, select from the following options, then click Next to continue.
■ Printer Utilities
Installs utility files for selecting printer features.
■ Network Utilities
Installs utility files for using the printer on a network.
■ Samplers
Installs color sampler charts and a fonts sampler.
Use the default Destination Directory or click Browse.
Files are copied to your computer’s hard disk.
d. The PhaserShare Installation dialog box appears. PhaserShare software consists of two applications for use on
Novell NetWare networks: a printer status application for users and a printer administration application for system
administrators. Make selections from the following options, then click Next to continue:
■ Both PhaserShare Status Monitor and Administrator
■ PhaserShare Status Monitor
■ PhaserShare Administrator
■ Do Not Install PhaserShare
e. Select PhaserShare installation type, then click Next to continue:
■ Standard Install (automatically installs the choice you made in the previous dialog box)
■ Network Install (copies PhaserShare installation files to a network server)
f. If you selected the PhaserShare Network Install option, click Browse to select the drive for installing the
installation files. Click Next to continue. Click OK in the installation successful dialog box.
Files are copied to your computer’s hard disk or a selected network destination.
Note: To use the PhaserShare software installer you copied to a network server, go to the location of the copied
files, and run SETUP.EXE. Follow the installation prompts to install PhaserShare software on local NetWare-enabled
workstations.
User Manual
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
6. The Finish Installation dialog box contains instructions for
completing the printer software setup; click Next. The Print
Manager opens automatically.
7. From the Printer menu select Create Printer.
8. In the Create Printer dialog box, under Driver, select Other.
9. Type in the drive for the printerÕs CD-ROM or diskette, click OK.
10. In the Select Driver dialog box, under Printer Driver, select your
Phaser 360 printer, and click OK.
11. In the Create Printer dialog box, select a local printer port, or
follow the instructions below for a network port:
LPR port (for TCP/IP) setup instructions
AppleTalk port setup instructions
a. In the Print Destinations dialog box, under Available a. In the Print Destinations dialog box, under Available
Print Monitors, select LPR Port and click OK; the
Print Monitors, select AppleTalk Printing Devices.
b. Click OK.
b. For Name or address of server providing lpd, type
your printer’s IP address (or Host name if known to
the network).
c. In the Available AppleTalk Printing Devices dialog
box, double-click on the appropriate zone (if there are
multiple AppleTalk zones).
Note: The printer’s IP address may be available on the
printer’s Configuration Page. If not, ask your
network administrator.
d. Select your Tektronix printer and click OK.
e. At the prompt: Do you want to capture this
AppleTalk Printing Device?, click No.
c. For Name of printer or print queue on that server,
Note: ClickingYes hides the printer from regular
Macintosh users, forcing them to use NT Server as a
spooler, as long as NT Server allows sharing of this
printer.
type in one of the following (use uppercase letters):
■ PS or PostScript
■ AUTO for automatic selection
d. Click OK.
f. In the Printer Properties dialog box, click OK.
e. Continue with the instructions in Step 12.
g. Continue with the instructions in Step 12.
12. Select options in the PostScript Printer Setup dialog box, and
click OK. Enabling the Use Printer Halftoning option is
recommended.
13. In the Print Manager, from the Printer menu select Exit.
14. In the Installation Completed dialog box, click Finish.
3-12
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Printer Software
3
Installing printer software for Windows 3.1
Note
If you are installing from diskettes, you may need more than one
diskette depending on your Windows system. Keep all of the
printer’s diskettes handy during the installation, and insert each
diskette when you are prompted by the installation program. The
Tektronix driver is available on both CD-ROM and diskette; the
AdobePS 3 driver is available on CD-ROM only.
1. Insert either the printerÕs CD-ROM or the Phaser 360 Color
Printer Installer for Windows Disk 1 into the appropriate drive on
your computer.
2. From the File menu, select Run.
3. Type in the drive for the CD-ROM or diskette, type SETUP and
click OK.
4. In the Installer, click Next until the Select Installation Type dialog
box appears.
5. Select either Easy Installation or Custom Installation, and
click Next. When you Þnish with the Easy or Custom
instructions, continue with Step 6 on page 3-15.
Easy Installation
a. The following files are copied to your computer’s hard disk:
■ Tektronix Printer Driver
■ QuarkXPress PDF
Installs an application-specific printer description file, if the application is found.
■ PhaserPrint Plug-in for Photoshop
Installs an application-specific plug-in.
■ Samplers
Installs color sampler charts and a fonts sampler.
b. In the Choose Destination Directory dialog box, select the location for installing the PhaserPrint plug-in.
c. Click Next.
Files are copied to your computer’s hard disk.
User Manual
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
Custom Installation
a. In the Driver Installation dialog box, select from the following options, then click Next to continue.
■ Drivers/PPDs
Installs driver files and printer description files.
■ QuarkXPress PDF
Installs an application-specific printer description file.
b. If you selected Drivers/PPDs in the previous window, the Custom Install: Select Drivers dialog box appears.
Select one of the following drivers and click Next:
■ Adobe Printer Driver for Windows 3.1
■ Tektronix Printer Driver for Windows 3.1
Note: The Tektronix Printer Driver for Windows 3.1 must be installed in the Windows directory (default Destination
Directory). Do not change the Destination Directory when installing the Tektronix driver unless you are installing the
driver on a network and you know the location of the Windows directory on the network drive.
c. In the Custom Install: Select Utilities dialog box, select from the following options, then click Next to continue.
■ Printer Utilities
Installs utility files for selecting printer features.
■ Network Utilities
Installs utility files for using the printer on a network.
■ Samplers
Installs color sampler charts and a fonts sampler.
Use the default Destination Directory or click Browse.
Files are copied to your computer’s hard disk.
d. The PhaserShare Installation dialog box appears. PhaserShare software consists of two applications for use on
Novell NetWare networks: a printer status application for users and a printer administration application for system
administrators. Make selections from the following options, then click Next to continue:
■ Both PhaserShare Status Monitor and Administrator
■ PhaserShare Status Monitor
■ PhaserShare Administrator
■ Do Not Install PhaserShare
e. Select PhaserShare installation type, then click Next to continue:
■ Standard Install (automatically installs the choice you made in the previous dialog box)
■ Network Install (copies PhaserShare installation files to a network server)
f. If you selected the PhaserShare Network Install option, click Browse to select the drive for installing the
installation files. Click Next to continue. Click OK in the installation successful dialog box.
Files are copied to your computer’s hard disk or a selected network destination.
Note: To use the PhaserShare software installer you copied to a network server, go to the location of the copied
files, and run SETUP.EXE. Follow the installation prompts to install PhaserShare software on local NetWare-enabled
workstations.
3-14
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Printer Software
3
6. If you are installing the Tektronix driver, select your Tektronix
Phaser 360 printer and click Next.
7. The Finish Installation dialog box contains instructions for
completing the printer software setup; click Next.
8. In the Installation Completed dialog box, click Finish.
9. Continue with the setup instructions depending on the driver you
selected in the installer:
Tektronix Driver for Windows 3.1:
Setup instructions
AdobePS 3 Driver for Windows 3.1:
Setup instructions
If you selected Easy Installation, or if you selected If you selected the AdobePS 3 Driver forWindows 3.1 in the
the Tektronix Driver for Windows 3.1 in the
Custom Installation, continue with the following
instructions:
Custom Installation, continue with the following instructions:
a. In the Adobe installer, click Read or Skip in the
README.WRI dialog box to start the installation.
a. Open the Windows Control Panel.
b. Click Continue in the PostScript Printer Driver Setup
b. Open the Printers dialog box.
dialog box. Files are copied to your computer.
c. Under Installed Printers, select your
c. Click the Restart Windows button in the dialog box that
Phaser 360 (TekColor) printer, click Connect.
appears.
d. Select the printer’s port, and click OK.
d. After Windows restarts, the Install PostScript Printer
from PPD dialog box opens. Select your Tektronix
Phaser 360 printer in the list and click Install.
e. Click OK in the next dialog box.
f. Click Close in the Install PostScript Printer from PPD
dialog box.
g. Click OK in the information dialog box.
h. In the Control Panel, double-click Printers.
i. In the Printers dialog box, select the printer you just
installed, and click Connect.
j. In the Connect dialog box, select the port the printer is
connected to, and click OK.
User Manual
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
Mac OS software
Use the installer application on the printerÕs CD-ROM or diskettes to install
the printerÕs standard software. Then, continue with driver-speciÞc setup
instructions for the driver you are using.
Installer options
Custom Easy
Software
Description
Installed folder
LaserWriter8.3.4Driver Driver for use with all (non-GX) Macintosh
System Folder: Extensions
systems.
Install
Install
Phaser 360 Driver
Custom driver based on the
LaserWriter 7.1.2 printer driver.
System Folder: Extensions
System Folder: Extensions
(Select
any of
these
(Installs
these
files)
Phaser 360 GX Driver
Printer Descriptions
Driver for use with QuickDraw GX.
items)
PPD for use with drivers and applications.
System Folder: Extensions:
Printer Descriptions
ColorSync Profile
Printer profile for use with ColorSync 2.0.
Color sampler charts and a fonts sampler.
System Folder: Preferences:
ColorSync™ Profiles
Samplers
PhaserTools: Samplers
QuarkXPress PDF File
File for use with the QuarkXPress
application. This file is installed only if you
have the QuarkXPress application.
QuarkXPress application
folder: PDF folder
PhaserPrint Photoshop Custom plug-in for printing from Adobe
Photoshop application folder
PhaserTools: Printer Utilities
Plug-in
Photoshop. This file is installed only if you
have the Photoshop application.
Printer Utilities
Printer utility files for controlling printer
features.
Network Utilities
PANTONE® Files
Utility files for using the printer on a network. PhaserTools: Network Utilities
PANTONE® Color library files and sampler
chart.
PhaserTools: Pantone Files
3-16
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Printer Software
3
Using the Mac OS installer
1. Insert either the printerÕs CD-ROM or the Phaser 360 Installer for
Mac OS Disk 1 into the appropriate drive on your computer.
2. Double-click the Phaser 360 Installer icon. Click Continue until
the Easy Install window appears.
3. Select Easy Install or Custom Install:
Easy Install
Custom Install
the Easy Install window. pull-down menu.
c. Click the I buttons for information on
each item.
items.
4. Continue with driver setup instructions depending on the driver
you are using:
■
■
■
If you want to use the LaserWriter 7.1.2-based driver, see ÒSetting
up the Phaser 360 printer driverÓ on page 3-18.
For most applications, see ÒSetting up the Apple LaserWriter 8.3.4
driverÓ on page 3-19.
If you are using QuickDraw GX, see ÒSetting up the Phaser 360 GX
driverÓ on page 3-21.
User Manual
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
Setting up the Phaser 360 printer driver
The Phaser 360 printer driver is a Tektronix-modiÞed version of Apple's
LaserWriter 7.1.2 printer driver. Use the Phaser 360 printer driver if you are
using System Software 6.0.7, or 7.0 and later.
1. Install the printerÕs software as described on page 3-17. Choose
Easy Install to install all of the necessary software, or select
Phaser 360 Driver in the Custom Install window.
2. Select Chooser from the Apple menu.
3. Click on the Phaser 360 printer driver icon on the left side of the
Chooser. A list appears with the printers you have connected to
your Macintosh or printers that are available on a network. (If the
printer driver icon does not appear, check the cable connections on
your computer and printer.)
4. Click on the Zone your printer is in. See your network
administrator if you have questions.
5. Click on your Phaser 360 printer in the list of printers on the right
side of the Chooser.
Close the Chooser by clicking its close box.
3-18
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Printer Software
3
Setting up the Apple LaserWriter 8.3.4 driver
The LaserWriter 8.3.4 driver uses printer-speciÞc PPDs (PostScript Printer
Description Þles) to learn a printerÕs page sizes, printing options, and media
type options. To use the LaserWriter 8.3.4 driver with a Phaser 360 printer,
do the following steps. If the printer is busy, it may take some time to
complete this conÞguration procedure; you may want to do this procedure
when the printer is idle. You have to conÞgure a printer only once.
Note
During installation, the LaserWriter 8.3.4 driver leaves other
versions of the LaserWriter driver (such as 7.x and 6.x) intact,
but overwrites an earlier version of the LaserWriter 8 driver, if
one exists.
1. Install the printerÕs software as described on page 3-17. Select
Easy Install to automatically install all of the necessary software,
or select LaserWriter 8.3.4 Driver and Printer Descriptions in the
Custom Install window.
2. From the Apple menu, open the Chooser.
3. Select the LaserWriter 8 driver icon.
4. Click on the Zone your printer is in. See your network
administrator if you have questions.
5. Select your printer from the list, then click the Setup button. An
auto-setup program searches for the printerÕs PostScript Printer
Description Þle (PPD).
You may see a dialog box showing the PPD Þle you installed in
Step 1. Click TKP360P1.PPD and click Select.
Or, if you donÕt see this Þle listed, click Other PPD. A dialog box
opens showing the PPD Þles you have installed in the
System Folder, Extensions folder, Printer Descriptions folder.
Click TKP360P1.PPD and click Select.
User Manual
3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
6. If the auto-setup Þnishes, a color icon appears next to the printerÕs
name in the Chooser.
If not, click OK at the prompt. In the dialog box that appears,
under Installable Options select items such as the optional Lower
Paper Tray Assembly, then click OK.
7. Click the Chooser’s close box.
3-20
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Printer Software
3
Setting up the Phaser 360 GX driver
If you are using Apple Macintosh QuickDraw GX, use the Phaser 360 GX
driver to print to your Phaser 360 printer.
■
■
The Phaser 360 GX driver works with QuickDraw GX and
non-QuickDraw GX applications.
drivers. If you want to print from non-QuickDraw GX
applications with a driver such as the LaserWriter 8.3.4, you must
Þrst disable QuickDraw GX.
■
QuickDraw GX is compatible with System Software 7.5 and later,
but not with Mac OS 8.0 and later.
Note
Refer to the on-line manual on the printer’s CD-ROM for details
on using the Phaser 360 GX driver.
1. Install the printerÕs software as described on page 3-17. Select
Easy Install to automatically install all of the necessary software,
or select Phaser 360 GX Driver in the Custom Install window.
2. From the Apple menu, select Chooser.
3. Click the Phaser 360 GX printer driver icon on the left side of the
Chooser. A list appears with the printers available on your
network. (If the printer driver icon does not appear, Restart your
Macintosh, and repeat the printer driver installation procedure;
also, check the cable connections on your computer and printer.)
4. Click on the Zone your printer is in. See your network
administrator if you have questions.
User Manual
3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
5. In the Connect via ÞeldÕs pop-up menu, select your printerÕs
communication method:
■
■
The AppleTalk option is the standard network connection.
The Servers option is used to select a shared desktop printer.
6. Click on your Phaser 360 printer in the list of printers on the right
side of the Chooser.
7. Click the Create button to create a desktop printer. An icon of the
printer appears on the desktop with the same name as the printer
selected in the Chooser.
8. Close the Chooser by clicking its close box.
3-22
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Printer Software
3
UNIX workstation software
PhaserPrint™ for UNIX software
For UNIX environments, Tektronix offers the optional PhaserPrintª for
UNIX software. PhaserPrint for UNIX software includes driver-selectable
printer options, and provides fast, raster Þle and screen copy printing to
Tektronix color printers. The printerÕs CD-ROM contains a demonstration
copy of the PhaserPrint for UNIX software, and an on-line instruction guide,
in the UNIXDEMO directory. To purchase a licensed copy of this software,
see page 10-6 for instructions.
Downloadable printer utility files
Note
Refer to the on-line manuals on the printer’s CD-ROM for more
information on printing from a workstation.
If you do not have a licensed copy of PhaserPrint for UNIX software, you
can use the PostScript utility Þles on the Phaser 360 printerÕs CD-ROM with
UNIX and VMS workstations. These Þles let you set up your spooling
system to select between media trays, print-quality modes, color correction
modes, and other print controls. UNIX workstation users can access utility
Þles in the following ways:
■
Copy the Þles from the Tektronix Phaser 360 printerÕs CD-ROM if
your system includes a CD-ROM drive. Workstation-speciÞc Þles
are located in the bin directory.
■
■
Copy the Þles from the printerÕs diskettes. Workstation Þles are
available in both Macintosh and PC format.
Access the Þles via the Internet:
■
■
http://www.tek.com/Color_Printers/support Home page
ftp://ftp.tek.com/cpid/bbs/<platform>/360
Utility Þles
(where <platform> is pcs, macintosh, or unix)
■
Download utility Þles from the Tektronix Bulletin Board
Service (BBS); refer to the printerÕs CD-ROM for information.
User Manual
3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing Printer Software
3-24
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
4
Printing Basics
You can print to your printer from PCs, Macintosh computers, and UNIX
the following topics:
■
■
■
(page 4-4)
The types and sizes of media (page 4-6) and trays (page 4-8) you
can use in your printer
Loading and printing letterhead, labels, and transparencies
(page 4-11)
■
■
■
■
Using the manual-feed slot (page 4-16)
Printing from a PC (page 4-19)
Printing from a Macintosh (page 4-35)
Printing from a UNIX workstation (page 4-41)
Note
Refer to the on-line manuals on the printer’s CD-ROM for
information on “Printing from DOS.”
User Manual
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Print features: overview
Once the appropriate printer driver is installed on your network or
computer, you can the select the following print features from the menus
available in your application software.
■
■
Paper or transparency printing
Tray selection (if you have the Lower Paper Tray Assembly
installed) or manual feeding
■
■
■
Print-quality (resolution) modes
Color correction modes (refer to page 5-2)
Quick Collate for collating multipage documents (requires an
external hard drive) (refer to page 5-9)
■
Check Print for previewing a sample printout before continuing a
print job (refer to page 5-10)
■
Image Smoothing tor improving low-resolution images
Selecting print features
There are three ways to select print features:
From your applications (recommended) To select print features from Windows
applications, refer to the table on page 4-20; to select print features from
Macintosh applications, refer to page 4-36. Settings from your software
application override the printerÕs front panel default settings.
Through your web browser Use your web browser to select print features and
view the status of the printer. Refer to the PhaserShare Networking System
Administrator Manual for complete information.
4-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
From the printer’s front panel Use the front panel for selecting print features
to ÒFront panel overviewÓ on page 6-1 for instructions on using the printerÕs
front panel.
Print features quick reference: Printer’s front panel
Feature
Feature
Front panel menu
descriptions
Print Quality Menu
Print-quality mode
■ Fast Color
■ Standard (default)
■ Enhanced (800 x 450 dpi)
TekColor Correction Menu
TekColor correction
See page 5-3.
■ Automatic (default)
■ None
■ Vivid Color
■ Display
■ SWOP
■ Euroscale
■ Commercial
■ Monochrome
Printer Defaults Menu
Media tray selection
(only with optional Lower
Paper Tray Assembly)
See page 4-8.
➥ Default Tray Menu
■ AutoSelect
■ Upper
■ Lower
Printer Defaults Menu
➥ Check Print
➥ Check Print Timeout
Printer Defaults Menu
➥ Image Smoothing
Check Print
See page 5-10.
See page 5-11.
■ Enabled
■ Disabled
Image Smoothing
■ Enabled
■ Disabled
Note
If your printer is networked and you change the front panel
settings, make sure that you tell other users on the network.
Printer settings affect all prints made with nonsupported drivers.
User Manual
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Adjusting print speed and resolution
You can adjust the print quality and speed for different documents and
purposes. Standard, the default setting, provides the best reproduction for
most business printing at 300 x 300 dots per inch (dpi). Select Fast Color for
the fastest printing, and select Enhanced for the highest resolution.
Print-quality
mode
Uses
Speed
(pages per minute)
Standard (default) ■ Crisp, bright prints; suitable for
■ 4 ppm paper
most office printing
■ 2 ppm transparency
■ Recommended mode for
high-quality transparencies:
produces vibrant, saturated
prints with smooth color
transitions
Fast Color
Enhanced
■ Quick presentations; drafts
■ 6 ppm paper
■ Superior text resolution and
smoothest color transitions on
paper (at 800 x 450 dpi)
■ 2 ppm paper
■ 2 ppm transparency
■ For transparencies when
very fine detail is important
(at 600 x 300 dpi)
If you have installed a driver from the printerÕs CD-ROM, select
print-quality modes from your computer: refer to the table on page 4-20 for
menus for Windows applications; refer to page 4-36 for Macintosh menus.
You can also select print quality at the printerÕs front panel. Refer to the
table on page 4-3 for the front panel selections.
4-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
All about media
The printer prints on letter- and A4-size ofÞce paper, transparencies, peel-off
labels (such as Avery 5160), and nonglossy cover stock. Tektronix premium
and standard grades of transparency media are designed to provide optimal
image quality and reliable operation. Tektronix premium transparencies
offer enhanced print quality and ink adhesion for overhead transparencies.
Note
Made For Each Other¨: Tektronix inks and transparencies are
formulated for use with this printer to ensure the best print
quality and long-term reliability. Tektronix does not guarantee
printer performance on non-Tektronix transparency media.
For information on ordering Tektronix transparencies and other media
supplies, refer to ÒPrinter suppliesÓ on page 10-2.
Caution
Never attempt two-sided or two-pass (duplex) printing on any type
of media. Ink already present on the media will offset onto the
internal paper path, requiring you to perform cleaning procedures.
To avoid damaging your printer, do not use perforated paper, three-holed
paper, legal-size paper, or envelopes.
Do not use transparency media intended for ink-jet or thermal-wax
printers.
Do not reuse paper that has already been fed through the printer, even if
no image has been printed. Oil and ink residue from the media may
offset onto printer parts, requiring you to clean the printer.
Keep media and other printer supplies in covered containers. Dust and
dirt can be transferred to paper or transparencies, resulting in poor print
quality. Paper that has been sitting out of its sealed wrapper can become
distorted, causing paper jams. Do not use creased or wrinkled paper.
To avoid having the paper stick together, gently fan the paper before
loading it into the paper tray.
User Manual
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Acceptable media sizes, types, and weight
The printer prints on either letter- or A4-size paper, depending on which
tray size you ordered. The following table shows the types and weight of
letter- or A4-size media you can load in the different trays:
Tray type
Media type
Paper/transparency ■ Paper
2
tray
60 – 120 g/m (16 – 32 lb.)
Capacity: 200 sheets
(Letter or A4)
■ Transparencies
Capacity: 50 sheets
■ Full-sheet laser printer labels
Capacity: 50 sheets
High-capacity
transparency tray
(Letter or A4)
■ Transparencies
Capacity: 175 sheets
■ Labels
Capacity: 100 sheets
Lower Paper Tray
Assembly
(Letter or A4)
■ Paper only
2
60 – 120 g/m (16 – 32 lb.)
Capacity: 625 sheets 90 g/m (24 lb.)
2
Manual feed
(Letter or A4)
■ Paper
2
60 – 120 g/m (16 – 32 lb.)
■ Nonglossy cover stock
2
135 – 220 g/m (50 – 80 lb.)
■ Transparencies
■ Full-sheet laser printer labels
■
■
Print on plain paper, including copier paper and recycled paper,
bond, letterhead, and cover stock.
You can recycle the paper printed on this printer the same way
you would recycle paper from any laser printer.
4-6
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Margins and image area
The image area is the part of the media where the image appears. When the
printer places an image on the media, the image area is a bit smaller than the
actual media size. You may need to adjust the page margins in your
application software to match the image area. The printer must be set for the
correct size media through the printer driver.
The image area for the Phaser 360 printer is 8.11 x 10.45 in. (letter-size) and
200 x 283 mm (A4-size). The difference between the image area and the
media size for the top margin and side margins is 5 mm (0.2 in.). The bottom
margin is 9 mm (0.35 in.).
Note
For maximum print speed, set left and right margins to 7.4 mm
(0.3 in.) or larger.
The following illustration shows the image area and top, side, and bottom
margins.
1. Letter-size: 8.5 x 11 in.
2. A4-size: 210 x 297 mm
1
5 mm (0.2 in.)
2
5 mm (0.2 in.)
8.11 in.
10.45 in.
200 mm
283 mm
9 mm (0.35 in.)
9 mm (0.35 in.)
9922-14
User Manual
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Media trays
Standard paper trays The printer is shipped with a standard letter- or A4-size
paper tray that holds 200 sheets (slightly less than one-half ream) of paper.
Use the standard paper tray for paper, letterhead, and label stock.
Note
The standard paper trays are designed for use with paper. You
can use a standard paper tray for printing up to 50 transparency
sheets. However, you must use a supported printer driver to
specify Transparency as the paper source and confirm the
selection at the front panel. Refer to page 4-13 for details on
printing transparencies.
capacity of 175 sheets (approximately three boxes). Using both paper and
transparency trays, you can quickly switch between paper and transparency
print jobs by simply swapping media trays in the printer.
Lower Paper Tray Assembly In workgroup or high-volume printing
environments, you will want to add the optional 625-sheet Lower Paper Tray
Assembly to supplement the standard paper tray. The Lower Paper Tray is
convenient when you want to print on paper (lower tray) and another
media, such as transparency, letterhead, or label stock (upper tray). With
dual-tray capability, you can print on different media directly from the
printer driver without the need to leave your computer to switch trays.
Refer to ÒLower Paper Tray AssemblyÓ on page 10-4 for ordering
information.
Note
The Lower Paper Tray Assembly accepts paper only; it should not
be used with labels or transparencies.
4-8
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Media tray settings
You can control the source of a print job from your computer. The media
tray choices available in your application menus depend on the number and
types of trays you have in use, the type of driver you have installed from the
printerÕs CD-ROM, and the printerÕs default setting.
AutoSelect If this selection appears in your menu, it acts as the default. The
printer automatically prints from the upper tray if you are printing in a
single-tray conÞguration. If you have a Lower Paper Tray Assembly, it
prints from the lower tray. If you have trays in both slots, the printer
Paper This is the initial setting for Windows drivers. If you select Paper and
the standard media tray is installed, the printer will print on whatever
media is loaded in the upper tray. If you have the Lower Paper Tray
Assembly installed, selecting Paper feeds paper from the lower tray. If you
and will prompt you to load paper.
Transparency Select Transparency whenever you print transparencies. If
print selection at the printerÕs front panel. Refer to page 4-14 for directions
on printing transparencies from the standard paper tray.
sheets of paper or card stock (up to 220 g/m2 [80 lb.]). Select this option
from your computer, then feed the paper into the printer when prompted by
the front panel. Refer to ÒWhen to use the manual-feed slotÓ on page 4-16
for more details on using manual feed.
Manual Transparency Select Manual Transparency to hand feed single
transparency sheets into the printer. Refer to ÒWhen to use the manual-feed
slotÓ on page 4-16 for more details on using manual feed.
Upper/Lower Use these settings to change printing trays if you have
installed the optional Lower Paper Tray Assembly. See ÒChanging the
default media tray settingÓ on page 4-10.
User Manual
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Changing the default media tray setting
These instructions apply if you install the optional Lower Paper Tray
Assembly.
Default setting
When the Lower Paper Tray Assembly is Þrst installed, the default media
tray selection is set to AutoSelect. With this setting, the printer
automatically prints from the lower paper tray. In addition, note the
following: When the lower paper tray becomes empty, the printer then
automatically switches to the upper tray. If a paper tray is installed in the upper
tray slot, then the printer prints on whatever media is loaded in the upper
tray. However, if a transparency tray is installed, then the printer prompts
you to load paper in the Lower Paper Tray Assembly.
Changing to Upper and Lower settings
When you add the Lower Paper Tray Assembly to your printer, you may
want to change the default media tray setting. By resetting the default, you
override the printerÕs automatic switching from the lower paper tray to the
set the default selection to Lower, the printer will automatically print from
the Lower Paper Tray Assembly until otherwise instructed. When you want
to print from the upper tray, for example, to print letterhead or labels, you
then change the paper source or media tray setting to Upper from your
computer. Always explicitly select Transparency to print transparencies
from an upper tray.
To reset the default media tray:
■
From the printerÕs front panel, Þrst select the Printer Defaults
menu. Next select Default Trayand then make your selection.
Refer to page 6-3 for information on using the front panel controls.
■
Use a PostScript utility Þle. Refer to the printerÕs CD-ROM for
more information on downloading utility Þles.
Note
When using a supported printer driver, settings from your
software application override the printer’s default media tray
setting.
4-10
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Printing letterhead
1. Load letterhead face up in the standard paper tray with the bottom
edge of the page closest to the paper tray handle.
12345678
9922-09
2. Print from your software application in the usual way. Refer to
ÒPrinting from a PCÓ on page 4-19 and ÒPrinting from a
MacintoshÓ on page 4-35.
Caution
Some letterhead may be printed with ink that will offset onto
the printer’s parts, requiring you to perform cleaning
procedures. Run several test sheets of letterhead to check for
letterhead smearing before attempting a large print job.
User Manual
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Printing labels
1. Use standard full-sheet peel-off labels.
2. Load labels face up in the standard paper tray.
9922-11
3. Print from your software application in the usual way. Refer to
ÒPrinting from a PCÓ on page 4-19 and ÒPrinting from a
MacintoshÓ on page 4-35.
Caution
To prevent the printer from jamming, do not load partially used
sheets of labels, and use only “frameless” labels; when labels
are removed, no material is left on the backing.
4-12
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Printing transparencies
Use Tektronix transparency media for optimal image quality and reliable
printer operation. Tektronix offers two transparency grades, standard and
premium. Tektronix premium transparencies provide enhanced ink
adhesion and print quality.
Note
Handle transparencies by the edges and with both hands to avoid
fingerprints and creases, which can result in poor print quality.
Printing transparencies from the transparency tray
1. Load Tektronix premium transparencies with the notched corner of
the sheet in the back-right corner of the tray. Load Tektronix
standard transparencies in any orientation. You can load up to
175 sheets (about three boxes) in the transparency tray. A label
inside the transparency tray indicates the trayÕs maximum
transparency capacity.
9922-06
2. Print from your computer in the usual way, but select
Transparency as the Paper Source or Tray Selection. Click Print.
User Manual
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Printing transparencies from the standard paper tray
1. Print from your computer in the usual way, but select
2. Go to the printer. The front panel ßashes the following pair of
messages:
Waiting for Transparency
Continue Cancel
Load Tray
Continue Cancel
3. Pull out the paper tray and load the transparencies. You can load
up to 50 transparencies in the standard tray. Refer to page 4-13 for
instructions on loading Tektronix premium transparencies. Insert
the paper tray.
4. Press Continue.
5. When printing is completed, remove the extra transparencies from
the paper tray and replace them with paper.
Note
Order the optional transparency tray for greater convenience. It
has a 175-sheet capacity, and you can print directly from your
application.
4-14
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Transparency quality tips
■
■
■
Use Tektronix transparencies, available in standard and premium
grades. Tektronix premium transparencies offer enhanced print
quality and ink adhesion.
Select Standard as the print-quality mode for vibrant, saturated
prints with smooth color transitions. This is the recommended
mode for most transparency printing.
Select the Enhanced print-quality mode for transparencies only
when very Þne detail is important. Note that selecting this mode
for transparency printing produces 600 x 300 dpi, not
800 x 450 dpi.
■
■
Use large type on overheads; 18-point or larger type works well.
Use yellow or other light colors for text on solid-color
backgrounds.
■
Use Tektronix transparency sleeves to protect your transparencies,
make them easier to handle, and make your presentations more
professional by covering blank areas exposed on your overhead
projector.
■
■
If not using Tektronix transparency sleeves, place slip sheets
between printed transparencies or use a protective cover to
prevent contact between transparencies.
Use a printer driver installed from the printerÕs CD-ROM for
nonsupported driver, the printer will use the printing mode of the
tray (paper) and produce unsatisfactory results.
Note
Do not load transparencies in the Lower Paper Tray Assembly.
To prevent jams, do not reuse transparencies that have already been fed
through the printer, for example, after a jam or if the transparency was
ejected without being printed.
Do not use transparency media intended for ink-jet or thermal-wax
printers. For best results, use Tektronix transparency media. Refer to
“Printer supplies” on page 10-2 and “Media trays” on page 10-4 for
ordering information.
User Manual
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
When to use the manual-feed slot
Use the manual-feed slot to feed single sheets for printing, especially when
you want to print on heavier paper or cover stock. The manual-feed slot will
accept nonglossy cover stock of 135 to 220 g/m2 (50 to 80 lb.).
1. Through a supported printer driver, select Manual Paper or
Manual Transparency from your computer. Refer to the tables on
page 4-20 and page 4-36 for PC and Macintosh menus,
respectively.
2. In the dialog box, click the Print button.
3. Go to the printer and open the manual-feed cover using the
recessed Þnger tab.
4. Set the guide on the inside of the manual-feed cover for letter- or
A4-size media.
3
4
LETTER
A4
9922-47
4-16
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
5. When prompted by the front panel, insert one sheet of paper or
transparency media until the sheet stops.
■
Manually feeding letterhead: Orient the sheet of letterhead face down
) and feed the bottom edge Þrst ( ).
(a
b
■
Manually feeding transparencies: Feed Tektronix premium
transparencies with the notch (c) toward you and on the right side
(d). Standard Tektronix transparencies are not notched and can be
fed in any orientation.
c
a
12345678
LETTER
A4
12
b
d
9922-12
User Manual
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
6. After the Þrst sheet enters the printer, wait for the front panel to
prompt you before feeding the next sheet (about 5 seconds).
LETTER
5 Sec.
A4
9922-18
Note
A jam error will occur if you feed the second sheet of media into
the manual-feed slot before the front panel prompts you.
4-18
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Printing from a PC
You can print from a PC with or without a Tektronix-provided printer driver.
printing selections from the printerÕs front panel.
Using Windows printer drivers
To select printer-speciÞc features, print from one of the following provided
drivers. See page 4-20 for a reference table listing the printing features, and
how to Þnd them quickly, in each of these drivers.
Windows 95
Windows 3.1
see page 4-22
see page 4-25
see page 4-29
see page 4-31
see page 4-31
Tektronix-modified Microsoft driver
AdobePS 3 driver
Windows NT 3.51
Windows NT 4.0
Microsoft PostScript driver
Microsoft PostScript driver
Using the printer’s front panel
Without a supported driver, you can make some printing selections from the
printerÕs front panel. Refer to page 4-3 for a list of front panel selections and
to page 6-1 for instructions on using the front panel.
Downloading utility files
For information on selecting print options with utility Þles, refer to the
on-line documents on the printerÕs CD-ROM or the Tektronix Color Printer
web site.
User Manual
4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Print features quick reference: Windows printer drivers
Windows 3.1
Windows 95
Windows NT 4.0
AdobePS3Driver
Tektronix Driver
AdobePS 4 Driver
Microsoft Driver
Follow these
basic driver
instructions
to select
printer
features:
1. From Control Panel,
1. From Control Panel,
1. Select Start.
1. Select Start.
double-click Printers.
double-click Printers.
2. Select Settings then
2. Select Settings then
2. Select Phaser 360
2. Select Phaser 360
Printers.
Printers.
printer.
printer.
3. Right mouse click
3. Right mouse click
3. Click Setup.
3. Click the buttons to
Phaser 360 printer.
Phaser 360 printer.
select printer features.
4. Click the tabs to select
4. Select Properties.
4. Select Properties.
printer features.
5. Click the tabs to select 5. Click the tabs to select
features.
features.
a. Click Paper tab.
b. Select a Paper Size:
■ Letter
a. Click Setup.
b. Select a Paper Size:
■ Letter
a. Click Paper tab.
b. Select a Paper Size:
■ Letter
a. Click Advanced tab.
b. Locate Paper/Output.
c. Select a Paper Size:
■ Letter
Media size
(see also
page 4-6)
■ A4
■ A4
■ A4
■ A4
a. Click Paper tab.
a. Click Setup.
a. Click Paper tab.
a. Click Advanced tab.
b. Locate Paper/Output.
Tray
selection
(see also
page 4-8,
page 4-9)
b. Select a Paper
b. Select a Paper
b. Select a Paper
Source:
Source:
Source:
c. Select a Paper
■ Upper
■ Upper
■ Upper
Source:
■ Lower
■ Lower
■ Lower
■ Upper
■ Paper
■ Paper
■ Paper
■ Lower
■ Transparency
■ Manual Paper
■ Transparency
■ Manual Paper
■ Transparency
■ Manual Paper
■ Paper
■ Transparency
■ Manual Paper
■ Manual
■ Manual
■ Manual
Transparency
Transparency
Transparency
■ Manual
Transparency
Note: to see all trays in
the list, go to the Features
tab and select Optional
Lower Trays Installed.
Note: to see all trays
in the list, go to the Device
Settings tab, to
Installable Options, click
Optional Lower Trays,
click Installed.
a. Click Features tab.
b. Select a Print Quality: b. Click Options.
a. Click Setup.
a. Click Device Options
a. Click Advanced tab.
Print-quality
modes
tab.
b. Locate Printer
(see also
page 4-4)
b. Locate Printer
features.
■ Fast Color
■ Standard
■ Enhanced
c. Click Printer Features.
d. Select a Print Quality:
■ Fast Color
features.
c. Select a Print Quality:
■ Fast Color
c. Select a Print Quality:
■ Fast Color
■ Standard
■ Standard
■ Standard
■ Enhanced
■ Enhanced
■ Enhanced
4-20
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Print features quick reference: Windows printer drivers (cont'd.)
Windows 3.1 Windows 95
Windows NT 4.0
AdobePS3Driver
Tektronix Driver
AdobePS 4 Driver
Microsoft Driver
basic driver
instructions
to select
printer
features:
1. From Control Panel,
1. From Control Panel,
1. Select Start.
1. Select Start.
double-click Printers.
double-click Printers.
2. Select Settings then
2. Select Settings then
2. Select Phaser 360
2. Select Phaser 360
Printers.
Printers.
printer.
printer.
3. Right mouse click
3. Right mouse click
3. Click Setup.
3. Click the buttons to
Phaser 360 printer.
Phaser 360 printer.
select printer features.
4. Click the tabs to select
4. Select Properties.
4. Select Properties.
printer features.
5. Click the tabs to select 5. Click the tabs to select
features.
features.
a. Click Features tab.
a. Click Setup.
b. Click Options.
c. Click Printer Features.
a. Click Device Options
a. Click Advanced tab.
Color
tab.
corrections
(see also
page 5-2)
b. Select a Color
b. Locate Printer
Correction:
b. Locate Printer
features.
features.
■ Automatic
c. Select a Color
d. Select a Color
c. Select a Color
Correction:
■ None
Correction:
Correction:
■ Automatic
■ Vivid Color
■ Automatic
■ Automatic
■ None
■ Simulate Display
■ SWOP Press
■ Euroscale Press
■ Commercial Press
■ Monochrome
■ Use Printer Setting
■ None
■ None
■ Vivid Color
■ Vivid Color
■ Vivid Color
■ Simulate Display
■ SWOP Press
■ Euroscale Press
■ Commercial Press
■ Monochrome
■ Use Printer Setting
■ Simulate Display
■ SWOP Press
■ Euroscale Press
■ Commercial Press
■ Monochrome
■ Use Printer Setting
■ Simulate Display
■ SWOP Press
■ Euroscale Press
■ Commercial Press
■ Monochrome
■ Use Printer Setting
a. Click Features tab.
a. Click Setup.
b. Click Options.
c. Click Printer Features.
a. Click Device Options
a. Click Advanced tab.
Quick
tab.
Collate
(see also
b. Locate Printer
b. Select Quick Collate
features.
checkbox.
b. Locate Printer
features.
c. Select Quick Collate
d. Select Quick Collate
checkbox.
c. Select Quick Collate
checkbox.
checkbox.
a. Click Features tab.
a. Click Setup.
b. Click Options.
c. Click Printer Features.
a. Click Device Options
a. Click Advanced tab.
Check Print
(see also
page 5-10)
tab.
b. Locate Printer
b. Select Check Print
features.
checkbox.
b. Locate Printer
features.
c. Select Check Print
d. Select Check Print
checkbox.
c. Select Check Print
checkbox.
checkbox.
a. Click Features tab.
a. Click Setup.
b. Click Options.
c. Click Printer Features.
a. Click Device Options
a. Click Advanced tab.
Image
tab.
Smoothing
(see also
page 5-11)
b. Locate Printer
b. Select Image
features.
Smoothing checkbox.
b. Locate Printer
features.
c. Select Image
d. Select Image
Smoothing checkbox.
c. Select Image
Smoothing checkbox.
Smoothing checkbox.
User Manual
4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Using the AdobePS 4 driver with Windows 95
To select printing options, follow these steps:
1. From the taskbar, select Start. In the menu that appears, select
Settings, then Printers.
2. In the Printers window, click the Phaser 360 printer icon with the
right mouse button, then select Properties from the menu.
3. Click the following tabs to see printing options; refer to your
Windows 95 documentation for more information on tabs and
options.
Details tab
Click the Details tab to access timeout settings and other options.
■
Set the Timeout settings if your printer is connected to a local
port.
Not Selected: Type a value in this text box to change the number
of seconds Windows waits before notifying you that a printer is
off-line. The default is 15 seconds and is recommended.
Transmission Retry: On large or multiple-page documents, you
may see an Alert message that the printer is no longer accepting
data before the job is completely sent to the printer. To avoid this
Alert message, set this option to a larger value, such as
900 seconds (15 minutes).
Paper tab
Click the Paper tab to see media options, such as Paper Size and
Paper Source (for selecting media trays and media types).
4-22
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Graphics tab
Click the Graphics tab to see graphics options.
■
To change the print-quality modes (resolution or dpi settings), use
the Print Quality selections in the Device Options tab. The
Print Quality selections override the Resolution options in the
Graphics tab.
■
If you are using host color correction, you need to make selections
in both the Graphics and Device Options tabs. Refer to the
on-line manuals on the printerÕs CD-ROM for more information
on host color correction.
Device Options tab
Click the Device Options tab to see printer-speciÞc options.
■
In the Printer features scroll list, select options such as Color
Corrections. In the next Þeld, select the Color Correction you
want, such as Automatic.
■
In the Installable Options scroll list, select options such as the
Optional Lower Tray or Optional Hard Drive.
User Manual
4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
PostScript tab
Click the PostScript tab to see PostScript-related options.
■
Under PostScript timeout values, make these selections:
■
■
Leave the Job Timeout set to 0.
Set the Wait Timeout to a high value, such as 900 seconds
(15 minutes) to make sure you do not lose a multipage job due
to a timeout after the Transmission Retry Alert message is
displayed.
■
The PostScript header contains important PostScript information
that must accompany each print job; it is not a banner page printed
with each job. If an option is not selected, an error message is
displayed on your computer screen and your job does not print.
Click one of the following in the PostScript header Þeld:
Select Download header with each print job. This option
downloads PostScript header information with each print job.
This is the recommended setting.
Click the Send Header Now button to save the PostScript header
information in the printer, then select the Assume header is
downloaded and retained option. This option makes print Þles a
little smaller and faster than the Þrst option, but you need to click
the Send Header Now button every time the printer is turned on.
■
Click the Advanced button to see more options.
■
For PostScript language level, select 3. Click OK when
Þnished.
Note
For faster printing, select Binary communications protocol
under Data format.
4-24
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Using the Tektronix driver for Windows 3.1
To select printing options, follow these steps:
1. From the Control Panel, double-click the Printers icon.
installed printers.
3. Click the Set As Default Printer button if you want to select your
printer as the default.
4. Click the Connect button; the Connect dialog box appears.
5. Select the port your printer is connected to.
The printerÕs ConÞguration Page contains the information you
need to set up the printerÕs port. Refer to ÒPrinting a
ConÞguration PageÓ on page 2-25 for instructions on printing the
ConÞguration Page.
Interface
Parallel
Select
LPTx
Then do the following
Go to Step 6.
Network
Network port
(LPTx or COMx)
1. Click the Network button to open
the Printers-Network
Connections dialog box.
2. Fill in each item based on your
configuration, then click OK.
Refer to your Microsoft Windows
documentation for details, or ask
your network administrator for help.
Note
You can use CONNECT TO FILE to save a document as a
PostScript file instead of sending it to the printer. For more
information, see your Microsoft Windows documentation.
User Manual
4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
6. Set the Timeouts. These options regulate your computerÕs
communications with its printer ports.
■
Device Not Selected: Type a value in this text box to change
the number of seconds Windows waits before notifying you
that a printer is off-line. The default is 15 seconds, and is
recommended.
■
Transmission Retry: On large or multiple-page documents
you may see an Alert message that the printer is no longer
accepting data before the job is completely downloaded to the
printer. To avoid the Alert message, set this option to a larger
value, such as 900 seconds (15 minutes).
7. Click OK to return to the Printers dialog box, then click the Setup
button. A dialog box appears with the name of the printer you
selected across the top. Use this dialog box to select paper source,
paper size, number of copies, and image orientation.
Note
You may want to set the number of copies from your application
because the number of copies in the Setup dialog box remains the
same until you change it again. Also, if you are printing multiple
copies, make sure the Transmission Retry is set for at least
600 seconds (10 minutes).
8. From the Setup dialog box, click the Options button to see the
Options dialog box. Refer to your Microsoft Windows
documentation for details on the options in this dialog box. Make
sure the Color check box is on to print in color. Select one of the
following header options:
■
Make sure the Send Header with Each Job check box is on to
download PostScript header information with each print job.
This is the recommended setting.
■
Click the Send Header button. In the Send Header dialog
box, select either Printer or File, and click the Send Now
button. This saves the PostScript header information in the
printer. This option makes print Þles a little smaller and faster,
but you need to click the Send Now button every time the
printer is turned on.
4-26
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
9. From the Options dialog box, click the Printer Features button to
see the Tektronix Printer Features dialog box. Make color
correction and print quality selections in this dialog box. Click OK
to return to the Options dialog box.
10. From the Options dialog box, click the Advanced button to see the
Advanced Options dialog box. Make sure the Use PostScript
Level 2 Features check box is checked on.
Note
The Use PostScript Level 2 Features option affects the print
time of bitmapped (raster) images by improving the image
transfer time from the computer to the printer, and by improving
the image processing time in the printer. This option is only
available to applications that use this Tektronix driver with
Tektronix PostScript Level 2 printers, such as the Phaser 360
printer. When this box is checked, the Compress Bitmaps
option is unavailable (grayed-out).
11. Click OK until you return to the Printers dialog box, then click
Close.
User Manual
4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
If you are using PC/NFS
If you have PC/NFS software installed on your computer, you need to make
the following selection in the Network Options dialog box:
1. From the Main window, double-click the Print Manager icon.
2. From the Options menu in the Print Manager, select
Network Settings.
3. In the Network Options dialog box, uncheck the
Print Net Jobs Direct box.
4. Click OK.
4-28
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Using the Adobe PostScript driver for Windows 3.1
To select printing options, follow these steps:
1. From the Control Panel, double-click Printers.
2. In the Printers dialog box, select the Tektronix Phaser 360 printer,
then click Connect.
3. In the Connect dialog box, set the Timeout settings, then click OK:
■
Device Not Selected: Type a value in this text box to change
the number of seconds Windows waits before notifying you
that a printer is off-line. The default is 15 seconds, and is
recommended.
■
Transmission Retry: On large or multiple-page documents
you may see an Alert message that the printer is no longer
accepting data before the job is completely sent to the printer.
To avoid the Alert message, set this option to a larger value,
such as 900 seconds (15 minutes).
4. In the Printers dialog box, click Setup. A dialog box appears with
the printerÕs name across the top.
5. Click the following tabs to see printing options; refer to your
Windows documentation for more information on tabs and
options.
Paper tab
Click the Paper tab to see media options, such as Paper Size and
Paper Source (for selecting media trays and media types).
Features tab
Click the Features tab to see printer-speciÞc options, such as Color
Corrections, Print Quality modes, and Optional Lower Tray.
User Manual
4-29
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
PostScript tab
Click the PostScript tab to see PostScript-related options.
■
■
In the Performance Options Þeld, select the Use Language Level
2 or 3 Features option.
Under PostScript timeout values, make these selections:
■
■
Leave the Job Timeout set to 0.
Set the Wait Timeout to a high value, such as 900 seconds
(15 minutes) to make sure you do not lose a multipage job due
to a timeout after the Transmission Retry Alert message is
displayed.
Job Control tab
Click the Job Control tab to see job-related options.
■
The PostScript header contains important PostScript information
that must accompany each print job; it is not a banner page
printed with each job. If an option is not selected, an error
message is displayed on your computer screen and your job does
not print. Click one of the following in the PostScript Header
Þeld:
■
Select Download Each Job. This option downloads PostScript
header information with each print job, and is the recommended
setting.
■
Select the Already Downloaded option to save the PostScript
header information in the printer, then click the Download button.
This option makes print Þles a little smaller and faster than the Þrst
option, but you need to click the Download button every time the
printer is turned off or reset.
■
For better performance, select the Binary Mode option.
4-30
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Using the Windows NT 3.51 PostScript driver
If you are using Microsoft Windows NT, follow the instructions in
ÒInstalling printer software for Windows NT 3.51Ó on page 3-10 to install a
Windows NT PostScript driver with a Phaser 360 printer. You can select
printer page sizes in the driver for Windows NT applications, however,
TekColor color corrections and other PostScript Level 2 features are not
supported by the Windows NT driver. Refer to page 4-3 for instructions on
selecting color corrections from the printerÕs front panel or from
downloadable utility Þles. Refer to your Microsoft Windows NT
documentation for details on features in the Windows NT driver.
Using the Windows NT 4.0 PostScript driver
Setting up installed options
Note If you are not sure which printer options you have installed, the
printer’s Startup Page lists some of this information, such as
SCSI hard disks. You can print a copy of the Startup Page from
the printer’s front panel.
1. From the taskbar, click Start, then Settings and Printers.
2. In the Printers dialog box, click the right mouse button on the
Phaser 360 printer, and select Properties in the menu.
3. From the Properties dialog box, click the Device Settings tab.
4. In the Device Setting sheet, scroll to the end of the list to
Installable Options.
5. Under Installable Options, highlight Optional Lower Tray.
6. In the box that appears at the bottom of the window, click
Installed.
7. Select other options you have installed, such as Optional Hard
Drive.
8. Click OK to return to the Control Panel.
User Manual
4-31
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Making default settings
1. From the taskbar, click Start, then Settings and Printers.
2. In the Printers dialog box, click the right mouse button on the
Phaser 360 printer, and select Properties in the menu.
3. From the Properties dialog box, click the Device Settings tab.
4. In the Device Settings sheet, locate Form To Tray Assignment.
5. Under Form To Tray Assignment, highlight the Þrst tray.
6. In the box that appears at the bottom of the window, select the size
media you will be using in that tray.
7. Repeat Steps 3 and 4 for each installed tray.
8. Click OK to return to the Control Panel.
Selecting a printer's Default Document Properties
Note
Document properties set from an application always override
document defaults set in the printer' s Document Properties
sheets. However, if an application does not set a document
property (such as page orientation or paper size), the printer
defaults to the document properties set in the printer' s
Document Properties sheets.
1. From the taskbar, click Start, then Settings and Printers.
2. In the Printers dialog box, click the right mouse button on the
Phaser 360 printer, and select Document Defaults in the menu.
3. Click the Advanced tab. Under Document Options, select a
printer feature then make your selection in the next Þeld. For
example, select Color Corrections in the Þrst list, then select an
option, such as Automatic, in the next list.
4. Click the Page Setup tab to see other features, such as Paper Size
and Paper Source.
4-32
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Selecting printer options within an application: Print
1. From the File menu, select Print; the Print dialog box appears.
You can select a different printer and other settings in this
dialog box.
2. Click on the Properties button; the Printer Document Properties
sheet appears.
3. Click the Advanced tab to change any printer features, including
TekColor color corrections. This tab displays the same
information as the Document Defaults Properties Advanced tab.
4. Click the Page Setup tab to see other features. This tab displays
the same information as the Document Defaults Properties Page
Setup tab.
Note
Changes to any of these settings overrides the Default Printer
Properties settings in the Printers folder.
Selecting printer options within an application: Page Setup
Note
If changing the Printer Driver settings through Page Setup
causes problems with the application you are using, then change
the Printer Driver settings through Print under the File menu,
described on page 4-33.
1. From the File menu, select Page Setup; the Page Setup dialog box
appears.
2. Under Paper, select Size and Source options.
Note
Selecting Automatically Select as the Paper Source uses the
default setting made under Document Defaults in the Printers
folder. To change this setting, select a different Source in
Page Setup.
User Manual
4-33
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
3. Click the Printer button; another Page Setup dialog box appears.
You can select a different printer here.
4. Click the Properties button; the Printer Document Properties
sheet appears.
5. Click the Advanced tab to change any printer features, including
TekColor. This tab displays the same information as the
Document Defaults Properties Advanced tab.
6. Click the Page Setup tab to see other features. This tab displays
the same information as the Document Defaults Properties Page
Setup tab.
Note
Changes to any of these settings overrides the Default Printer
Properties settings in the Printers folder.
Printing from MS-DOS
Refer to the on-line manuals on the printerÕs CD-ROM for information on
printing from MS-DOS.
4-34
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Printing from a Macintosh
To print from a Macintosh, you need a printer driver. Installing one of the
features.
Using Macintosh printer drivers
To select printer-speciÞc features, print from one of the following provided
Phaser 360 driver (based on LaserWriter 7.1.2)
Phaser 360 GX driver (for use with QuickDraw GX)
Apple LaserWriter 8 driver (for most applications)
see page 4-38
see page 4-40
see page 4-39
Using the printer’s front panel
Without a supported driver, you can make some printing selections from the
printerÕs front panel. Refer to page 4-3 for a list of front panel selections and
to page 6-1 for instructions on using the front panel.
Downloading utility files
For information on selecting print options with utility Þles, refer to the
on-line documents on the printerÕs CD-ROM or the Tektronix World Wide
Web site.
User Manual
4-35
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Driver name
Apple LaserWriter 8
Phaser 360
Phaser 360 GX
driver instructions to
select printer features:
1. Make sure the driver software is installed.
2. Make sure your printer is selected and set up in the Chooser.
3. From the File menu, select either Print or Page Setup as listed below.
For GX, also use the Printing menu in the Finder.
4. Select printer features as indicated.
a. Open Page Setup dialog
a. Open Page Setup dialog box. a. Open Page Setup dialog
Media size
box.
box.
(page 4-6)
b. Select a Paper Size:
■ Letter
b. Select a Paper Size:
■ Letter
b. Select a Paper Size:
■ Letter
■ A4
■ A4
■ A4
a. Open Print dialog box.
b. Click TekColor button.
c. Select a Tray Selection:
■ Upper
a. Open Print dialog box.
b. Select a Paper Source:
■ Upper
a. Open the Printer Driver
Tray selection
Defaults dialog box.
(page 4-8, page 4-9)
b. Select a Tray Selection:
■ Upper
■ Lower
■ Lower
■ Lower
■ Paper
■ Paper
■ Paper
■ Transparency
■ Manual Paper
■ Manual Transparency
■ Transparency
■ Manual Paper
■ Manual Transparency
■ Transparency
■ Manual Paper
■ Manual Transparency
a. Open Print dialog box.
b. Click TekColor button.
c. Select a Print Quality:
■ Fast Color
a. Open Print dialog box.
b. Click Options button.
c. Select a Print Quality:
■ Fast Color
a. Open Printer Driver
Print quality modes
Defaults dialog box.
(page 4-4)
b. Select a Print Quality:
■ Fast Color
■ Standard
■ Standard
■ Standard
■ Enhanced
■ Enhanced
■ Enhanced
4-36
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Driver name
Phaser 360
Apple LaserWriter 8
Phaser 360 GX
Follow these basic
driver instructions to
select printer features:
1. Make sure the driver software is installed.
2. Make sure your printer is selected and set up in the Chooser.
3. From the File menu, select either Print or Page Setup as listed below.
For GX, also use the Printing menu in the Finder.
4. Select printer features as indicated.
a. Open Print dialog box.
b. Click TekColor button.
a. Open Print dialog box.
b. Click Options button.
a. Open the Printer Driver
Color correction
Defaults dialog box.
b. Select a Color Correction:
■ Automatic
c. Select a Color Correction: c. Select a Color Correction:
■ Automatic
■ Automatic
■ None
■ None
■ None
■ Vivid Color
■ Vivid Color
■ Vivid Color
■ Simulate Display
■ SWOP Press
■ Simulate Display
■ SWOP Press
■ Euroscale Press
■ Commercial Press
■ Monochrome
■ Use Printer Setting
■ Simulate Display
■ SWOP Press
■ Euroscale Press
■ Commercial Press
■ Monochrome
■ Use Printer Setting
■ Euroscale Press
■ Commercial Press
■ Monochrome
■ Use Printer Setting
a. Open Print dialog box.
b. Click TekColor button.
a. Open Print dialog box.
b. Click Options button.
a. Open the Printer Driver
Quick Collate
Defaults dialog box.
(page 5-9)
b. Select Quick Collate
c. Select Quick Collate
c. Select Quick Collate
checkbox.
checkbox.
checkbox.
a. Open Print dialog box.
b. Click TekColor button.
a. Open Print dialog box.
b. Click Options button.
a. Open the Printer Driver
Check Print
Defaults dialog box.
(page 5-10)
b. Select Check Print
c. Select Check Print
c. Select Check Print
checkbox.
checkbox.
checkbox.
a. Open Print dialog box.
b. Click TekColor button.
a. Open Print dialog box.
b. Click Options button.
a. Open the Printer Driver
Image Smoothing
Defaults dialog box.
(page 5-11)
b. Select Image Smoothing
c. Select Image Smoothing
c. Select Image Smoothing
checkbox.
checkbox.
checkbox.
User Manual
4-37
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Using the Phaser 360 printer driver
Select media size
1. From the File menu, open the Page Setup dialog box.
2. Use the Paper pop-up menu to select the printerÕs supported
paper sizes.
Select printer-specific options
1. From the File menu, open the Print dialog box.
2. In the Print dialog box, click the TekColor button to see the
TekColor Options dialog box.
3. Select printer-speciÞc options:
■
■
■
■
■
■
Color Correction
Quick Collate
Tray Selection
Check Print
Print Quality
Image Smoothing
4-38
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Using the Apple LaserWriter 8 printer driver
Select media size
1. From the File menu, open the Page Setup dialog box.
2. To select the printerÕs supported paper sizes, use the Paper
pop-up menu.
Select printer-specific options
1. From the File menu, open the Print dialog box.
2. In the Paper Source Þeld, select the media tray by location or
type.
3. Click the Options button to see the Print Options dialog box.
4. Select printer-speciÞc options:
■
■
■
■
■
■
Color Correction
Quick Collate
Tray Selection
Check Print
Print Quality
Image Smoothing
User Manual
4-39
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Using the Phaser 360 GX printer driver
Note
Refer to the on-line manuals on the printer’s CD-ROM for details
on using the Phaser 360 GX printer driver.
Printing with a desktop printer
If you are using QuickDraw GX applications, do one of the following:
■
■
Select any desktop printer in the Print dialog box.
Drag a document onto a desktop printer icon. The application
corresponding to the document opens, prints the document, and
then quits.
If you are using non-QuickDraw GX applications, do one of the following:
■
Print to the default desktop printer with the Print command from
the File menu.
■
Drag a document onto a desktop printer icon. The application
corresponding to the document opens, displays the Print dialog
box, and waits for you to click Print. After printing the document,
the application quits.
Selecting printing options
Most of the commands in the Printing menu are standard QuickDraw GX
driver commands, and are documented by Apple (see the Macintosh Guide
on-line document for details). The last group of commands in this menu are
printer-speciÞc.
Use the Printer Driver Defaults command in the Printing menu to set
default options for the selected desktop printer.
Note
The printer defaults dialog box is also available through the Print
command in the File menu for QuickDraw GX applications.
4-40
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Basics
4
Printing from a UNIX workstation
Overview
You can print from a UNIX workstation through Ethernet, Token Ring, or
parallel interfaces. Workstation users can print from any application that
generates color PostScript or print screen shots with the PhaserPrint
software.
For instructions and examples on creating print queues for your speciÞc
platform, visit the Tektronix web site:
http://www.tek.com/Color_Printers/
Or, you can contact Tektronix Customer Support at 1-800-835-6100.
To use the TekColor color corrections and other printer features, use one of
the following methods:
■
■
■
PhaserPrintª for UNIX software functions like a printer driver for
selecting printing options, and provides fast screen copy printing.
The menus on the printerÕs front panel let you select printing options;
refer to page 6-1 for instructions on using the front panel.
Downloadable utility Þles let you select printing options; refer to the
on-line manuals on the printerÕs CD-ROM for instructions.
User Manual
4-41
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
UNIX workstations
For UNIX environments, Tektronix offers the optional PhaserPrintª for
UNIX software which offers driver-selectable printer options and provides
fast, raster Þle and screen copy printing to Tektronix color printers.
PhaserPrint for UNIX software is available for these workstations:
Workstation
Sun
Operating System
SunOS 4.1.4, Solaris 2.3 and 2.4
IRIX 5.2, 5.3, 6.2, 6.3, and 6.4
HP-UX 9.0.5 and 10.2
SGI
HP 9000 700/800
IBM RS/6000
DECstation
DEC Alpha AXP
AIX 3.2 and 4.2
ULTRIX 4.0 and 4.4
OSF/1 3.0, 3.2, and Digital UNIX 4.0
The printerÕs CD-ROM contains a demonstration copy of PhaserPrint for
UNIX software and an on-line instruction guide in the unix/unixdemo
directory. If you would like to purchase a licensed version of PhaserPrint
software, contact your dealer or local Tektronix ofÞce. For ordering
information, refer to ÒAdditional software (UNIX and VMS)PhaserPrintª
for UNIX softwareÓ on page 10-6.
4-42
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
OpenVMS workstations
To print from OpenVMS workstations, the optional PhaserSymª utility, a
VMS print symbiont, functions as a driver for selecting printing options and
as a queue manager. PhaserSym software is compatible with DEC
workstations running OpenVMS version 5.0 and later. PhaserSym software
for proper communication with the printer. For ordering information, refer
to ÒAdditional software (UNIX and VMS)PhaserPrintª for UNIX softwareÓ
on page 10-6.
Additional information and tips are available through the following
resources:
■
Tektronix web site:
http://www.tek.com/Color_Printers/userdoc/introduction.html
■
HAL: Request a document catalog from HAL, the Tektronix fax
library. Refer to ÒGetting information by faxÓ on page 9-3 for
instructions.
User Manual
4-43
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printing Basics
Printing from specific applications
For printing from most applications, follow the instructions beginning on
page 3-1 to install drivers and printer software. Some applications require
additional conÞguration or page description Þles, which may have been
installed with the driver. Additional information and tips are available
through the following resources:
■
Tektronix web site:
http://www.tek.com/Color_Printers/userdoc/introduction.html
■
HAL: Request a document catalog from HAL, the Tektronix fax
library. Refer to ÒGetting information by faxÓ on page 9-3 for
instructions.
4-44
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
5
■
■
■
■
■
■
■
ÒUsing the Quick Collate optionÓ on page 5-9
ÒPreviewing with Check PrintÓ on page 5-10
ÒUsing Image SmoothingÓ on page 5-11
ÒPrinter languagesÓ on page 5-12
ÒWorking with fontsÓ on page 5-12
ÒImproving print speedÓ on page 5-16
User Manual
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Printing: Beyond the Basics
Adjusting the color of your prints
You may occasionally want to adjust the color of your prints for speciÞc
objectives, such as printing on transparencies. The following table lists the
TekColor color correction modes and their functions. A more detailed
description of each mode follows.
Select a color correction mode from your software application, at the
printerÕs front panel, or with downloadable utility Þles.
To select print features from Windows applications, refer to the table on
page 4-20; to select print features from Macintosh applications, refer to
page 4-36. Settings from your software application override the printerÕs
front panel default settings.
Printing objective or problem
Color correction to use
General office printing: Automatic optimizes the color
quality for each element on a page — text, photos, and
graphics — for the best overall color.
Automatic (default: make
no selection)
Brightest, most saturated transparencies.
Vivid Color
Presentation graphics — bar and pie charts, spread
sheets, organization charts.
Colors simulate computer display screen.*
Simulate Display
Graphic arts applications; colors simulate a printing
press standard.
SWOP Press
Euroscale Press
Commercial Press
Turn off all color corrections.
Use PANTONE charts.
None
Print in gray scale.
Monochrome
Use printer’s current color default.
Use Adobe’s standard color conversions.
Use Printer Setting
Refer to the printer’s
CD-ROM for downloadable
utility files.
* For other ways of matching the screen’s colors, use ColorSync color matching on a Macintosh or
use host color correction in Windows 95. Refer to the printer’s CD-ROM or the Tektronix web site
for more information.
5-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing: Beyond the Basics
5
TekColor correction descriptions
The following options are available.
Note
TekColor color corrections do not affect colors specified in the
PostScript Level 2 international color standard CIE XYZ,
developed by the Commission Internationale de l’Eclairage
(International Commission on Illumination).
Automatic: General all-purpose printing
The Automatic (default) option is the best choice for most ofÞce printing.
This mode optimizes the color quality on each page. The printer
automatically applies the appropriate color correction for each element (text,
graphics, photographs) for the best reproduction.
Vivid Color: Printing the brightest colors and a truer blue
The Vivid Color option makes printed blue appear less purple by reducing
the amount of magenta used to print blue colors. Other colors are also
adjusted to compensate for the adjusted blue. This selection also increases
contrast, making the output appear brighter. Use this selection for
presentation graphics, such as overhead transparencies, and for
bright-looking colors that donÕt need to match the screenÕs colors or printing
press colors.
Also use this option if you have speciÞed a color in the CMYK system, and
the color has a black component, and the color appears lighter than you
expected when printed. Vivid Color adjusts CMYK colors using a method
that adds black to other components. This option prints more saturated
(darker) colors and may be useful for printing overhead transparencies.
User Manual
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Printing: Beyond the Basics
Simulate Display: Simulating screen colors
The Simulate Display option makes printed colors approximate the colors
on a standard display screen. This selection should improve the
screen-to-printer color accuracy for most applications that donÕt perform
their own color corrections. This selection is best for applications that deÞne
colors as RGB (red, green, blue), HLS (hue, lightness, saturation), or HSB
(hue, saturation, brightness).
Press options: Matching printing press colors
There are three printing press color correction options. Each press option
conforms to a different printing standard. Use a press option if you are
previewing work for a four-color job to be printed on a printing press. These
options simulate a four-color commercial printing press, not solid spot
colors, such as PANTONE Colors.
Note
If you are selecting PANTONE Colors in your application, use
the None option; see page 5-5 for details. Also, use the None
option with other color management systems, such as EfiColor.
Printing press color corrections
Press option
SWOP Press
Inks
Base (paper) Target match (equivalent 3M Matchprint ®)
SWOP
Publication
Specification for Web Offset Publications.
These are specifications for color separation films
and color proofing that are used to ensure the
consistency of printed colors between different
publications. This option is typically used in the U.S.
Tends to be high-volume, web press printing.
Commercial Press Commercial Commercial
This option is typically used in the U.S. and is
characterized to match commercial 3M Matchprint
proofs.
Tends to be high-quality, sheet-fed printing.
Euroscale Press
Euroscale
Publication
This option is typically used in Europe and is
characterized to match the equivalent 3M
Matchprint.
5-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing: Beyond the Basics
5
None: Turning off all color corrections
If you do not want to use any TekColor color corrections, change the color
correction setting to None. Select None when you are doing the following:
■
■
Using applications that do their own color adjusting.
Using ColorSync on a Macintosh or host color correction in
Windows 95.
■
Printing PANTONE Colors using applications for which you have
installed a Phaser 360 PANTONE Color palette.
Monochrome: Printing in gray scale
The Monochrome option prints your color image as a monochrome gray
scale (shades of gray between black and white). Use this option to print
page masters for photocopying in black-and-white.
Use Printer Setting: Using the printer’s current default
The Use Printer Setting option is available only in the supported drivers.
This option sends no color correction information to the printer. It uses the
current default in the printer to process colors for printing. The factory
default color correction is Automatic. The printerÕs default can be one of
the following:
■
■
Any option selected in the TekColor Correctionmenu on the
printerÕs front panel.
One of the color correction utility Þles sent to the printer.
User Manual
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Printing: Beyond the Basics
Printing and using the color sampler charts
You can print color sampler charts from your printer to see how colors you
have speciÞed from within an application will look when printed. Having a
preprinted sample of each color can help you save time in selecting the
right one.
The color sampler charts available are CMYK (cyan, magenta, yellow, and
black), RGB (red, green, and blue), HSB (hue, saturation, and brightness),
and PANTONE Color. Print the color samples from Þles on the printerÕs
CD-ROM, from the Tektronix web site, or through your web browser. The
CMYK and RGB charts can also be printed from the Help Pages menu at the
printerÕs front panel.
Each color sampler chart is several pages long; the pages can be connected to
form a wall chart or placed in a binder for easy reference.
9922-132
5-6
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing: Beyond the Basics
5
Tips for working with color
Whether you are producing color reports, memos, graphs, charts, overhead
transparencies for presentations, color handouts, or design comps, there are
a few things to keep in mind when using color.
■
■
■
■
A large area of color looks more saturated (brighter) than a small
area of the same color.
A color looks brighter against a dark background than it does
against a white background.
Colors look different because of the background color or
surrounding colors.
The appearance of a color varies with the type and amount of
light, for example, ßuorescent lighting versus sunlight.
General guidelines
■
Keep a document or design simple and consistent.
■
Select colors that look good together and that reinforce your
message.
■
■
Check your application for standard palettes to get you started.
Use a color scheme of Þve or six shades, and in a series of images,
use the colors in a consistent manner throughout the series.
■
■
Use color to highlight the most important information, such as a
bar or pie segment in a chart or graph.
Use color to show relationships between objects, such as a range of
values. Objects with a similar meaning or value should be in
similar colors.
■
■
Use color as graphic elements in the design of newsletters, logos,
and brochures.
Avoid red and green combinations; these colors are hard for
people with red/green color blindness to distinguish.
User Manual
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Printing: Beyond the Basics
Special considerations
If your Phaser 360 printer is shared on a network
Another user may use the downloadable color correction utility Þles, or the
printerÕs front panel, to change the printerÕs default color correction setting.
If this situation occurs and you try to print through a nonsupported driver,
your prints may not turn out as expected. Refer to ÒSharing the printer on a
networkÓ on page 8-34 for more information.
Application color corrections
Some applications perform their own color corrections to improve
screen-to-printer color matching. The TekColor color correction options in
the supported drivers adjust colors in the printer after the application has
performed its color corrections.
■
■
■
If the application uses CIE (Commission Internationale de
lÕEclairage) colors, the TekColor corrections will not be applied.
If you select a TekColor color correction option other than None,
that selection may override some application features.
If you try one of the TekColor color correction options and the
printed results are not what you expected, then select the None
option and try reprinting your image.
■
Select the None TekColor color correction option if you are using
ColorSync color matching on a Macintosh or host color correction
in Windows 95 (refer to the printerÕs CD-ROM or the Tektronix
web site).
If you are using an unsupported driver
If you are not using one of the printer drivers shipped with the printer or
another driver that uses the Phaser 360 PPD (PostScript printer description)
Þles to control printer functions, then use the downloadable utility Þles from
the printerÕs CD-ROM or the printerÕs front panel to select color corrections.
5-8
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing: Beyond the Basics
5
multiple sets of documents. The collate function in some software
applications repeatedly sends each page to the printer in sequence until the
requested number of copies is printed. With the Phaser 360 printerÕs Quick
Collate option, the job is sent only once and then multiple collated sets are
produced by the printer, allowing much faster processing time.
Select Quick Collate through a supported driver, generally through the
Properties (Windows 95) or Print (Macintosh) menu. Refer to the charts on
page 4-20 and page 4-36, respectively.
Note
To use the Quick Collate feature you must attach an external SCSI
hard drive. Refer to “Tektronix external hard disk” on page 10-5 for
ordering information.
With an added 2.1 GBytes of external disk space, the printer collates up to
500 pages in Standard mode and 130 pages in Enhanced (800 x 450 dpi)
mode. Larger jobs are printed in collated batches. For example, to produce
four copies of a 140-page job in Enhanced mode, the printer outputs four
collated sets of the Þrst 130 pages and then four collated sets of the last
10 pages.
User Manual
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Printing: Beyond the Basics
Previewing with Check Print
With the Check Print option, the printer automatically stops after it prints
the Þrst page of a document, letting you check the document before printing
resumes. This function is especially useful when printing a large job.
Check Print is enabled as a default, with a timeout of 5 minutes: the printer
waits 5 minutes after printing the Þrst page of a document before it
continues printing. You conÞrm your choice to continue or cancel the print
job at the printerÕs front panel. To use the Check Print feature:
1. Select Check Print in a supported driver:
■
Windows 95 PostScript driver:
In the Device Options tab options, in the Printer features Þeld,
select Check Print.
■
■
AdobePS 3 driver for Windows 3.1:
In the Features tab options, select Check Print.
LaserWriter 8.x driver:
In the Print dialog box, click Options. In the Options dialog box, in
the Check Print drop-down menu, select True.
■
■
Phaser 360 driver:
In the Print dialog box, click TekColor. In the TekColor Options
dialog box, select Check Print.
Phaser 360 GX driver:
In the Print dialog box, in the TekColor printing extension, select
Check Print. (Or, from the Printing menu, in the Printer Driver
Defaults, select Check Print.)
2. Go to the printer. Check your Þrst print. At the Check Print
message on the printerÕs front panel, press one of the buttons:
■ Reprint: Reprints the Þrst page, then the printer pauses again for
the duration of the selected timeout or until you cancel or continue
the print job.
■ Cancel:Cancels the print job.
■ Continue:Continues printing the entire print job.
5-10
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing: Beyond the Basics
5
Setting the Check Print timeout
At the printerÕs front panel, scroll to the Printer Defaultsmenu, then
scroll to Check Print Timeout to reset the timeout value. Refer to
page 6-1 for information on using the printerÕs front panel.
Using Image Smoothing
Image Smoothing blends the adjacent colors in low-resolution images for
smoother color transitions. For example, use Image Smoothing to improve
the appearance of a 72-dpi image downloaded from the World Wide Web.
Image Smoothing is not recommended for 300-dpi or higher images.
There are three ways of selecting Image Smoothing:
■
■
■
Through the printerÕs front panel.
In a supported printer driver, check the Image Smoothing box on.
Through one of the following PostScript utility Þles:
Macintosh file name
PC file name
Image Smoothing On
Image Smoothing Off
SMOOTHON.PS
SMOOTHOFF.PS
Refer to the printerÕs CD-ROM for instructions on downloading
utility Þles.
User Manual
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Printing: Beyond the Basics
Printer languages
The printer supports PostScript Level 1 and Level 2; Postscript 3;
monochrome PCL5 (Printer Command Language); and HP-GL
(Hewlett-Packard Graphics Language) printer languages.
Refer to the printerÕs CD-ROM or the Tektronix web site for more
Working with fonts
Resident typefaces (PostScript and PCL5)
The printer is shipped with 164 PostScript fonts and a CD-ROM containing
ATM (Adobe Type Manager) software. ATM software helps your computer
display the fonts on screen as they will appear in your prints. Refer to
ÒPrinting a list of fontsÓ on page 5-15 for instructions on printing out a list of
the resident fonts.
For PCL5 printing, the printer supports the following typefaces in regular,
medium, bold, italic medium, and italic bold: Albertus, Antique, Arial,
Clarendon, Coronet, Courier, Garamond, Letter Gothic, Marigold, Times,
Times New Roman, Univers, and Wingdings.
5-12
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing: Beyond the Basics
5
Downloading fonts
The fonts resident in the printer are stored in the printer and are always
available for printing. The PostScript interpreter in the printer can also
accept and store additional fonts known as downloadable fonts. If you want
to print PostScript outline fonts that are not built into the printer, you can
transfer or download them from your computer to the printer.
Downloading fonts saves print time if you plan to print several documents
or a large document using those fonts.
When you download a font, it is stored in the printerÕs memory or on a SCSI
hard disk attached to the printer. Refer to the printerÕs CD-ROM for more
information on using an external SCSI disk for font storage. You can
download as many outline fonts as the printerÕs memory or hard disk allow.
Adding more printer memory expands the number of fonts that can be
downloaded to the printer.
The printer accepts Type 1 and Type 3 downloadable fonts including those
from Adobe, Agfa, Bitstream, Microsoft, and Apple; PCL5 fonts; and a
variety of user-deÞned fonts. The printer also accepts TrueType
downloadable fonts, which can be scaled to any point size. TrueType fonts
look the same on the screen as they do when printed.
You download a font from a PC or Macintosh the same way you download
fonts to any PostScript printer. Follow the documentation that was shipped
with your fonts.
User Manual
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Printing: Beyond the Basics
Using fonts with Windows
Before printing, you need to make sure the fonts speciÞed in your document
are installed in the printer or set up correctly in Windows. If you request a
font in an application that is not resident in the printer, or is not correctly
installed in Windows, the text is printed in the Courier typeface.
To use fonts that are not resident in the printer, do one of the following:
■
■
Use a font downloader supplied with your font package to
download the desired font to the printer.
Windows 3.1 users: Edit your WIN.INI Þle so the Windows driver
automatically downloads the fonts you need as part of a print job.
Refer to your Microsoft Windows documentation for details on
this procedure.
Some font packages automatically update the PostScript port
entries in your WIN.INI Þle when you reinstall the fonts. Refer to
the font packageÕs documentation for instructions.
For more information on using fonts with Windows, visit the Tektronix color
printer web site.
5-14
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Printing a list of fonts
You can print a list of the printerÕs resident fonts by downloading a utility
Þle to the printer.
Printing a font list from a Macintosh
1. Install the sampler and utility Þles from either the Installer for
Mac¨ OS Diskette 1 or the printerÕs CD-ROM; see page 3-17 for
details.
2. In the Chooser, select the appropriate printer.
3. On your computerÕs hard disk, locate the PhaserTools folder; locate
the Apple Printer Utility and double-click its icon to start the
application.
4. From the Utilities menu, choose Download PostScript File.
5. Select the Font Sampler Þle from the list, then click Open. (This Þle
was installed inside the PhaserTools folder, in the Samplers folder.)
6. If no output is returned by the printer, the Apple Printer Utility
displays a dialog box; click OK to continue.
Printing a font list from a PC
1. From the printerÕs CD-ROM or the Printer Software for Windows
diskette, locate the SAMPLERS directory and the FONTS.PS Þle.
2. Copy the FONTS.PS Þle to your computerÕs hard disk or use the
Þle directly from the CD-ROM.
3. To send the FONTS.PS Þle to the printer:
■
■
PC users: Use the DOS Copy command. (Windows 3.1 users can
also use the Copy command in the File Manager.)
Workstation users: Send the Þle to the printer as you would any
PostScript Þle.
User Manual
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Printing: Beyond the Basics
Improving print speed
Note
There are different ways to improve print speed, such as by
To speed the printing of a document with scanned images, here are some
suggestions:
■
When you use any color correction option (other than None), your
printer can take longer to process bitmapped images. Select color
corrections from the supported drivers, with downloadable utility
Þles, or from the printerÕs front panel; see ÒTekColor correction
descriptionsÓ on page 5-3 for more information.
■
The Fast Color print-quality mode is the fastest mode, followed by
the Standard print-quality mode and the Enhanced mode. Select
print-quality modes from the supported drivers, from the
printerÕs front panel, or through your web browser; see
ÒAdjusting print speed and resolutionÓ on page 4-4 for more
information.
Macintosh and Windows users
■
If you are using Adobe Photoshop, you can print using the
Tektronix PhaserPrintª software plug-in to improve the image
data transfer time from your computer to the printer. See the
on-line manual on the printerÕs CD-ROM for instructions on
installing and using the plug-in.
5-16
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing: Beyond the Basics
5
Windows 3.1 users
Note
Use the following procedure only if your computer is connected to
the printer through the parallel port. Do not do this procedure if
the printer is connected over a network port.
1. From the Control Panel, double-click Printers.
2. In the Printers dialog box, select the Tektronix Phaser 360 printer,
then click Setup. A dialog box appears with the printerÕs name
across the top.
3. Click the PostScript tab.
4. In the Performance Options Þeld, select the Use PostScript
Level 2 Features option.
5. Click the Job Control tab.
6. For better performance, select the Binary Mode option.
7. From your application, choose the Tektronix Phaser 360 as
your printer.
8. Try printing the document again.
User Manual
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Printing: Beyond the Basics
Windows 95 users
1. In the task bar on your screen, click the Start icon; a menu appears.
2. Move the cursor over Settings; another menu appears.
3. In the menu, click Printers; the Printers window appears.
4. In the Printers window, select the Phaser 360 printer icon. From
the File menu, select Properties.
5. Click the PostScript tab, then click the Advanced button.
6. Select Use PostScript Level 2 features.
not make this selection if the printer is connected over a network port.
8. Click Apply and then OK when Þnished.
9. Try printing the document again.
UNIX workstation users
Workstation users can use the PhaserPrint for UNIX software to signiÞcantly
increase printer performance when printing bitmapped images; refer to
ÒUNIX workstation softwareÓ on page 3-23 for details.
5-18
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing: Beyond the Basics
5
Selecting page sizes in Windows applications
In some Windows applications, you can select printer page sizes from the
File menu, in a Print Setup dialog box. If you use a Print Setup dialog box
to select the Phaser 360 printer from your application, some page sizes may
not be visible in the list.
If the Phaser 360 printer page size you want to use is not visible in the list, do
the following:
Windows 3.1
1. From the Main window, open the Control Panel and double-click
the Printers icon.
2. In the Printers dialog box, select the Phaser 360 printer in the list
of printers.
3. Click the Setup button.
4. In the Setup dialog box, select the page size you want and
click OK.
5. Return to your application. If you open the Print Setup dialog
box again from within your application, the page size selection
may be blank. The page size you just selected in the driver is still
selected; it is just not visible in the list.
6. Print as usual.
If you open the Print Setup dialog box from within an application, and the
page size selection is blank, the blank represents the page size last selected
from the printer driver through the Control Panel. You can leave the page
size selection blank and print as usual, or you can select another page size
from the list.
User Manual
5-19
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Printing: Beyond the Basics
Windows 95
1. In the task bar on your screen, click the Start icon; a menu appears.
2. Move the cursor over Settings; another menu appears.
3. In the menu, click Printers; the Printers window appears.
4. In the Printers window, select the Phaser 360 printer icon. Select
Properties from the File menu.
5. Click the Paper tab.
6. Choose your page size, click Apply, and then click OK.
7. Return to your application.
5-20
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
6
Using the Front Panel
Front panel overview
The printerÕs front panel includes an LCD display, menu buttons, and power
and error indicator lights. The two-line display shows the status of the
printer and menus for different printer operations, such as cleaning.
Front panel indicators
The front panel has two indicator lights:
1
Power Error
2
1
2
Ready
Info
Clean
Menu
Exit
9922-133
Indicator
On
Blinking
Off
1. Power
The printer is on and ready for
operation.
The printer is warming up, or it is The printer is off or not
processing or printing an image. ready, or there is an error.
The printer is in interactive
mode: you have pressed the
Menubutton.
2. Error
If the indicator is on after the
power-up sequence, the printer
detects an error that is not
user-correctable; the printer
requires service.
The printer requires attention:
for example, ink is low or the
printer is out of paper.
Normal operation.
User Manual
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Using the Front Panel
Two-line display
The two lines of the display have the following functions:
Line 1
■
Displays status messages such as Ready, Printing, or the
printerÕs name.
■
■
Displays operation errors and warnings such as Out Of Ink.
Displays the names of menus and parameters you can set.
Line 2
Displays button labels such as Infofor displaying printer
■
information, Cleanfor access to cleaning menus, and Menufor
access to a menu of selections. Other labels include <----for
previous, ---->for next, and OKto make selections.
1
Printing
Info
2
Clean
Menu
Exit
9922-134
Refer to ÒFront panel error messagesÓ on page 8-2 for a list of the front panel
messages. For an overview of the front panel menu selections, refer to
ÒFront panel menu mapÓ on page 6-5.
6-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Front Panel
6
Front panel buttons
1. The Exitbutton allows you to perform these menu functions:
■
Back up a level of the menu without making a selection.
Exit the menu.
■
2. Button 2, labeled Info, lets you cycle through information such
as the printerÕs name and the printerÕs IP address. Pressing Info
during a print job displays the job name and source. Pressing
Menuchanges Button 2 to the following:
■ <---- Scroll backward through the available selections.
3. Button 3, labeled Cleanduring normal operation, lets you access
the cleaning menus. Pressing Menuchanges Button 3 to the
following as you select submenus:
■ ---->
Scroll forward through the available selections.
■ Cancel Cancel a print job or selection.
■ Confirm ConÞrm an address change (IP, Broadcast, Gateway).
4. Button 4, labeled Menuduring normal operation, lets you enter the
front panel menu. Pressing Menuchanges Button 4 to the
following as you select submenus:
■ Menu
■ Print
■ OK
Provides access to submenus.
Executes the selected print.
Accepts the selected value.
Ready
Info
Clean
Menu
Exit
1
2
3
4
9922-66
User Manual
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Using the Front Panel
Enabling and disabling the front panel menu
The printer allows a system administrator to lock the front panel menu by
downloading a utility Þle. In this protected mode, you can only print the
pages in the Help Pages menu; you cannot modify any settings in the other
menus.
For more information on enabling and disabling the front panel menu, refer
to the printerÕs CD-ROM or the Tektronix web site.
■
■
■
When the front panel is enabled, all front panel menu selections
are available. When you press the Menubutton, the front panel
displays the following message:
Help Pages
<---- ----> Menu
When the front panel is disabled and you press the Menubutton,
the display shows only the pages in the Help Pages menu
(without the heading):
Configuration Page
<---- ----> Print
To access the entire menu with the front panel disabled, you must
use a special key sequence each time you want to enter the menu:
■
Press and hold down the Menubutton and press the Exitbutton.
The front panel displays the following message:
Help Pages
<---- ----> Menu
The full set of menus is now available.
6-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Front Panel
6
Front panel menu map
Phaser® 360 Menu Map
<---
--->
Scrolls backward through available selections
Scrolls forward through available selections
Enters the next submenu
Menu
Exit
OK
Menu
Press
Exits without making a change
Accepts the displayed value as the new setting
Help Pages
Menu Map
Configuration Page
Startup Page
Demonstration Page
RGB Color Sampler
CMYK Color Sampler
<---
<---
--->
Exit
Exit
Exit
Menu
Page Count
--->
View
TekColor Correction
None
Euroscale
Commercial
Monochrome
Automatic (default)
Vivid Color
Display
SWOP
<---
<---
<---
<---
<---
<---
--->
Menu
Menu
Menu
Print Quality
Fast Color
Standard (default)
Enhanced
--->
Exit
Exit
Exit
Exit
Exit
Printer Defaults
Default Tray
Startup Page
SCSI Startup Mode
Cleaning Page Source
Authorization Codes
Energy Star Timeout
Check Print
Check Print Timeout
Image Smoothing
Error Handler
--->
Network Settings
TCP/IP
EtherTalk
NetWare
HTTP
--->
Menu
Menu
Menu
Service Support
Cool Down For Power Off
Printer Serial Number
Head Serial Number
Calibration Date
Head Version
Engine FW Version
Fault History
--->
Purge Volume
Language
English (default)
Español
Français
Deutsch
Italiano
Japanese
--->
Appears when lower paper tray is installed.
9922-145
User Manual
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Using the Front Panel
Printer Help Pages
The printer has several Help Pages that you can print from the front panel to
learn more about the printer.
Menu Map
The menu map (see page 6-5) provides a graphical view of the front panel
menus. The menu map can be used as a convenient navigation aid for
quickly determining the location of menu items. An on-line version of the
menu map is also available at the Tektronix web site.
Configuration Page
The ConÞguration Page lists information on the printerÕs hardware and
software conÞguration and current settings. This page is especially useful
during network installation and troubleshooting. You can print the
ConÞguration Page through the front panel, by sending a PostScript utility
file to the printer (refer to the printerÕs CD-ROM), or through your web
browser (refer to the PhaserShare Networking System Administrator Manual).
Startup Page
The Startup Page lists the number of pages printed, installed interface ports,
software version numbers, installed RAM memory, the number of fonts in
memory, and other useful information.
Turning off the Startup Page By default, the Startup Page is printed every
time you power up the printer. You can disable the printing of the Startup
Page by resetting the default through the printerÕs front panel menu, by
sending a PostScript utility Þle to the printer, through the Apple Printer
Utility on the Macintosh, or through your web browser (refer to the
PhaserShare Networking System Administrator Manual).
Note
If the printer detects a nonfatal failure during power up, it
automatically prints a Startup Page containing diagnostic
information regardless of the Startup Page setting in the front
panel menu.
6-6
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Front Panel
6
Demonstration Page
This page is a sample color print you can print through the front panel or
through your web browser (refer to the PhaserShare Networking System
Administrator Manual).
RGB and CMYK Color Samplers
The RGB and CMYK color samplers provide multipage charts containing
color samples and their corresponding color values based on the RGB and
CMYK color models. Print these charts to help you select colors for use in
your documents. Refer to page 5-6 for an example.
Printing the Help Pages
1. While the Readymessage is displayed, press the Menubutton.
The printer displays the Þrst item in the menu:
Help Pages
<---- ----> Menu
2. To access the Help Pages, press the Menubutton. The following
message appears:
Menu Map
<---- ----> Print
3. Press the left arrow (<----)or right arrow (---->)buttons
until the Help Page you want appears, for example:
Configuration Page
<---- ----> Print
4. To print the page, press the Printbutton.
User Manual
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Using the Front Panel
Printer standby modes
Normal standby
When the printer is idle for more than 4 hours, it goes into a standby mode
that keeps the printer ready to use yet reduces energy consumption.
The printer exits standby mode when you send a Þle to the printer, press any
front panel button, install or remove a media tray, or open any cover. For
example, adding ink causes the printer to exit standby mode. When the
printer exits this standby mode, it is ready to print in about 5 minutes.
Energy Star mode
For printers ordered with the Energy Star option, the Energy Star default is
set to 1 hour. After an hour of inactivity, the printer cools down completely,
requiring you to wait 10Ð15 minutes to let the printer warm up before using
it again.
Because the printer uses ink during warm-up from a power-off condition
and when exiting the Energy Star mode, you can reduce ink consumption by
leaving the printer on. Always leaving the printer on, even during long
periods when the printer is not used, ensures optimum printing
performance and the best ink economy.
Increasing the Energy Star value from 1 hour keeps the printer ready for
printing and eliminates the warm-up period. The recommended setting is
999 hours. You can change the Energy Star mode through the front panel or
through your web browser (refer to the PhaserShare Networking System
Administrator Manual).
6-8
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
7
Caring For Your Printer
Overview
This chapter describes the following topics to help you care for the printer
and keep it in peak operating condition:
■
■
■
“Moving or shipping your printer” on page 7-2
from one location to another.
“Adding ink” on page 7-6
displays an Ink Lowmessage telling you when to add ink.
“Emptying the waste liner” on page 7-8
Empty the excess ink from the waste liner when a front panel message
tells you that the waste liner is full or whenever you remove the
maintenance tray.
■
■
“Replacing the maintenance tray” on page 7-11
Replace the maintenance tray when a front panel message tells you that
the maintenance tray is low, approximately every 12,500 prints.
“Cleaning the printer” on page 7-14
Describes how to clean the printer to solve speciÞc print problems: ink
smears on prints and problems feeding paper or transparencies from
the media trays.
User Manual
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
Moving or shipping your printer
Carefully follow the procedures listed below to avoid damaging your printer
when you need to move or ship it.
1. Latch all covers: Make sure that all doors and covers are Þrmly
latched to ensure that the printhead is parked. Do not turn off the
printer until the doors are closed to avoid damage to the printhead.
2. Turn off the printer: Wait for the printerÕs front panel to display
the Readymessage or the printerÕs name, then turn off the printer
using the rear-panel On/Off switch.
3. Unplug the printer: To prevent damage to the printhead and the power
supply, never turn off the printer by unplugging it.
4. Wait for 30 minutes: Let the printer cool down for at least
30 minutes before you proceed.
Caution
The printer must be allowed to cool down for at least
30 minutes before you move it so that the ink has time to
solidify. Failure to wait 30 minutes will likely result in an ink
spill that will damage the printer’s internal components.
7-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
5. Remove and store the maintenance tray:
a. Open the front cover and remove the maintenance tray from
the printer, keeping it level. Close the front cover.
9101-53
b. Remove, empty, and reinsert the waste liner into the
maintenance tray.
9922-13
User Manual
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
c. Place the maintenance tray in a plastic bag and seal the bag.
The maintenance tray contains drum ßuid that leaks if the tray
is tipped. Keep the maintenance tray level and in a sealed
plastic bag while transporting it.
Caution
To avoid potentially causing damages not covered by your
printer’s warranty, remove the maintenance tray before
moving or shipping the printer. Always store a used
maintenance tray in a leak-proof package and keep the tray
level. Never ship a partially used maintenance tray.
6. Lock the transit restraint:
a. Insert a wide ßat-blade screwdriver into the transit restraint
slot, located on the right side of the printer.
b. While pressing inward with medium pressure, turn the transit
restraint slot clockwise to lock the printhead. The lock button
is recessed from the side of the printer when fully engaged.
b
a
9922-136
7-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
Caution
To avoid damaging the printer’s internal components, always
turn the printer power off and lock the transit restraint before
moving the printer. Failure to do so may result in damage to
the printer’s internal components, and such damage may not
be covered by your printer’s warranty.
7. Repack the printer: Repack the printer in its original container. If
you no longer have the shipping box or if you have any questions
about the packing procedure, call your local dealer or in the U.S.
call Tektronix at 1-800-835-6100.
3
2
1
32434-06
User Manual
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
Adding ink
You do not have to wait for the printer to run out of ink before adding ink.
Prevent printing interruptions by periodically checking the ink supply and
adding ink sticks as necessary. The front panel displays Ink Low when the
level for one or more colors drops to one-half stick. When the printer is
completely out of ink, it displays an Out of Inkmessage.
1. Open the top cover. Note the color-coded label and the different
shapes of the slots of the ink-loading bin. Each ink stick color has
a unique shape.
2. Drop the ink stick(s) of the correct color and shape, with the
narrow (tapered) edge down, into the low or empty ink-loading
bin. You can load up to three ink sticks in each bin.
1
2
9922-21
3. Close the top cover.
Caution
Do not force ink sticks into the ink-loading bin. If an ink stick
does not load easily, make sure that the color and shape of the
ink stick correspond to the correct loading bin color and shape.
7-6
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
Ink consumption. Ink consumption is primarily dependent on the ink
coverage per print. Always keep a supply of ink sticks available to prevent
printing interruptions.
■
Refer to ÒPrinter suppliesÓ on page 10-2 for information on
ordering ColorStix ink sticks.
Ink handling tips
■
To ensure optimum print quality and best performance, leave the
printer turned on overnight and during weekends. Leaving the
printer on reduces the number of cleaning cycles, which consume
ink.
■
■
Keep ink sticks clean by storing them in their original containers
until you are ready to use them.
The ColorStix ink sticks will break if dropped; handle them with
care.
Caution
Use only Phaser 360 printer ColorStix ink sticks. The
Phaser 360 printer cannot use solid ink intended for other
printers, such as the Phaser 380 printer.
Do not load used ink into the printer; reusing waste ink ruins the
printhead. Your warranty will not cover repair of damages caused by the
reuse of waste ink.
Discard broken ink sticks. Loading broken pieces of ink sticks can cause
the ink-loading system to jam.
User Manual
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
Emptying the waste liner
The waste liner catches melted ink stick residue resulting from the printerÕs
self-cleaning operations. The blue plastic waste liner fits inside the
maintenance tray, which is located behind the front cover. Empty the waste
liner whenever you remove the maintenance tray or when the front panel
displays the following message:
Waste Liner (A) Full
Open Front Cover
1. Open the front cover.
9922-123
Caution
Some surfaces inside the printer may be hot. Be careful not to touch the
areas marked with this caution icon:
7-8
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
2. When you open the front cover, the following message appears:
Waste Liner (A) Full
Remove Tray (B)
3. Grasp the maintenance tray by the front edge (marked with a blue
ÒBÓ label) and lift up while sliding it out of the printer.
9101-53
Note
Once the maintenance tray has been partially used, it will leak
drum fluid if tipped. Place the maintenance tray on a flat surface
after removing it from the printer. Contact with the drum fluid
poses no known health risk. Refer to “MSDS for silicone oil
(drum fluid)” on page 11-6 for more information.
User Manual
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
4. Lift one corner of the waste liner handle to release it from the
maintenance tray; remove the waste liner.
5. Empty the contents of the waste liner by twisting it. Make sure
that you empty the waste liner completely before replacing it in
the maintenance tray. Used ink is nontoxic; it can be treated as
normal ofÞce waste.
6. Place the waste liner back in the maintenance tray.
a. Place the side opposite the handle into the maintenance tray
first.
b. Press down Þrmly in the center of the waste liner to snap it
into place. Make sure that the waste liner is fully seated in the
maintenance tray.
4
5
6
b
a
9101-39
7. Reinsert the maintenance tray into the printer.
Note
To prevent media jams at the media tray, be sure to push the
maintenance tray into the printer until both sides latch in place.
8. Close the front cover.
7-10
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
The maintenance tray is a disposable unit located inside the printer and
behind the front cover. It cleans the printerÕs drum, contains the waste liner
(a blue plastic insert) for used ink, and functions in other operations of the
printer.
A front panel message tells you when the maintenance tray is low. Install a
new maintenance tray to continue printing. Each replacement maintenance
tray has a print capacity of approximately 12,500 prints. To avoid printing
delays, keep an extra maintenance tray available for use in the printer.
■
Refer to ÒPrinter suppliesÓ on page 10-2 for information on
ordering the maintenance tray.
Note
There is a 15-minute warm-up period required after replacing the
maintenance tray.
1. Open the front cover.
9922-123
User Manual
7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
Caution
Some surfaces inside the printer may be hot. Be careful not to touch the
areas marked with this caution icon:
2. When you open the front cover, the following message appears:
Caution Hot Surfaces
Install New Tray (B)
3. Grasp the maintenance tray by the front edge (marked with a blue
ÒBÓ label) and lift up while sliding it out of the printer. Place the
maintenance tray on a level surface.
9101-53
Note
Once the maintenance tray has been partially used, it leaks drum
fluid if tipped. Never ship a partially used maintenance tray.
Never move or ship a printer with a maintenance tray
installed. Contact with the drum fluid poses no known health
risk. Refer to “MSDS for silicone oil (drum fluid)” on page 11-6
for more information.
7-12
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
4. Install the new maintenance tray by sliding it into the printer.
Make sure the tray slides in straight on both sides.
9922-38
5. Using both thumbs, push the tray in Þrmly until it latches.
9922-150
6. Close the front cover and wait for the printer to warm up (about
15 minutes).
7. To prevent leaking, seal the used maintenance tray in the plastic
bag from the new (replacement) maintenance tray. Treat the used
maintenance tray as normal ofÞce waste.
User Manual
7-13
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
Cleaning the printer
You need to clean the printer when the following occur:
■
■
Frequent media jams.
Prints are striped or smeared.
How often you need to clean the printer will depend on how heavily the
printer is used and the environment in which it is used.
To determine an approximate maintenance schedule: Record the date of
Using the front panel: Some cleaning procedures are executed through the
the procedures and on how to print cleaning instructions.
If the printer has frequent media jams
Problem
Cleaning procedure
Media jams or misfeeds at the
upper tray.
“Cleaning for upper media tray jams: media-pick
roller” on page 7-34.
Media jams or misfeeds at the
lower paper tray.
“Cleaning for lower tray jams: paper-pick rollers”
on page 7-43.
Media jams behind the front cover “Cleaning for jams and ink smears: paper-feed
or at the manual-feed slot.
rollers” on page 7-22.
Media jams or wraps around the
large black (transfix) roller inside
the exit cover.
“Cleaning for ink smears and jams: internal paper
path” on page 7-20.
7-14
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
7
If prints have light stripes or smears
Problem
Cleaning procedure
Light-colored stripes or missing
colors on prints.
“Light stripes on prints: cleaning the printhead” on
page 8-12.
Ink smears on the front, back, or
edges of a page.
1
“Cleaning for ink smears and jams: internal
paper path” on page 7-20.
2
“Cleaning for jams and ink smears: paper-feed
rollers” on page 7-22.
3
“Cleaning for ink smears: paper-exit path” on
page 7-28.
Oil (drum fluid) on top edge of
print.
3
“Cleaning for ink smears: paper-exit path” on
page 7-28.
9682-21
1
2
3
9922-29
User Manual
7-15
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
The Cleaning Page
The Cleaning Page, a page with a series of narrow, colored stripes, is output
each time the printhead is cleaned. More than one page may be printed.
This occurs at the following times:
■
When you run the cleaning procedure to eliminate light stripes in
your prints (see page 8-12)
■
■
During the printerÕs warming-up routine
After emerging from Energy Star standby mode
1
Red
2
Green
3
Blue
4
Black
1 2 3 4
Phaser® 360 Cleaning Page
This page prints to maintain optimal print quality.
9922-137
Selecting the Cleaning Page source
The default source for the Cleaning Page or other paper that the printer uses
in its cleaning procedures is the upper tray. When the Lower Paper Tray
Assembly is installed, you can ensure that the printer always uses paper
from the lower paper tray in its self-cleaning procedures by changing a
setting in the printerÕs front panel as follows:
7-16
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
1. While the Readymessage is displayed, press the Menubutton.
The printer displays the following message:
Help Pages
<---- ----> Menu
2. Using the left arrow (<----)or right arrow (---->)buttons,
scroll through the selections until the following message appears:
Printer Defaults
<---- ----> Menu
3. To access the printer defaults settings, press the Menubutton.
4. Using the left arrow (<----)or right arrow (---->)buttons,
scroll through the selection until the following message appears:
Cleaning Page Source
<---- ----> Menu
5. Press the Menubutton. The following message appears:
Cleaning Page Source:Upper*
<---- ----> OK
6. Press the right arrow (---->)button once. The following
message appears:
Cleaning Page Source:Lower
<---- ----> OK
7. Press the OKbutton to conÞrm the setting.
8. Press the Exitbutton until the printer displays Ready.
You can also change the default through a utility Þle (refer to the printerÕs
CD-ROM).
User Manual
7-17
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
Cleaning supplies
Your printer is shipped with a cleaning kit that contains the following
supplies:
1. Cleaning tray (media-pick roller)
2. Foam swabs
3. Lint-free cloth wipes (dry)
4. Plastic bottle for dispensing isopropyl alcohol
1
2
3
4
9101-24
Some cleaning procedures require you to use cloth wipes or swabs saturated
with isopropyl alcohol. Because regulations prohibit shipping alcohol or
presoaked cleaning materials with the printer, you must supply 90% pure
isopropyl alcohol (available at pharmacies).
Presoaked alcohol wipes When you reorder cleaning supplies, you
receive individually wrapped cloth wipes presoaked with isopropyl alcohol.
You can obtain these presoaked wipes either separately in 10-packs or as
part of a separate cleaning kit from Tektronix. For ordering information,
refer to ÒPrinter suppliesÓ on page 10-2.
7-18
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
opyl alcohol
Using isopr
A). Use the
e isopropyl alcohol (IP
ocedures requir
Some of the cleaning pr
e IPA, but if you do, you
You can use 90% pur
purest IPA (99%) available.
must wait after cleaning to make sur
cent IPA dries quickly; 90% IP
e completely
A may take several
e that the printer parts ar
dry. Ninety-nine per
.
minutes to dry
Caution
Rubbing alcohol may contain oils that leave undesirable
efully read the label on the
residue on printer parts. Car
only isopropyl
container. If the rubbing alcohol contains
water only to
alcohol and deionized water
the printer’s internal components, never use
clean them.
a lint-free cloth moistened with
uctions refer to
Whenever the cleaning instr
(B
). When the
presoaked alcohol cloth
(A), you can substitute a
isopropyl alcohol
uctions direct you to use an alcohol-soaked swab, you can use
cleaning instr
(
C).
esoaked alcohol cloth packet to moisten the swab
the extra alcohol in a pr
Warning Alcohol is flammable; keep alcohol-soaked cloths and swabs
away from hot surfaces.
efer to ÒPrinter suppliesÓ on
To order presoaked alcohol cloth wipes, r
page 10-2.
C
A
B
9101-25
User Manual
7-19
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
Cleaning for ink smears and jams: internal paper path
Approximate time to complete: 3–6 minutes
Clean the printerÕs internal paper path surfaces if you note the following:
■
Your prints have stray ink marks on the front or the back.
9922-20
■
The media is wrapping around the large black roller inside the exit
cover.
Caution
Always use clean sheets of paper to clean the paper path. Do
not reuse cleaning sheets. High-grade, heavier papers, such as
120 g/m2 (32 lb.) bond, work best.
Do not attempt duplex (two-sided) printing on any type of media. Ink
already present on the media offsets onto the internal paper path,
requiring you to perform cleaning procedures.
1. Load at least 10 sheets of clean, high-grade paper into the printer.
If your printer is conÞgured with just the upper media tray, load
that tray. If you have installed the Lower Paper Tray Assembly,
you can load either the upper tray or the lower tray. If you use the
lower paper tray, make sure that the printerÕs default has been
reset so that the printer will feed paper that it needs for its
cleaning procedures from the lower paper tray only. Refer to
ÒSelecting the Cleaning Page sourceÓ on page 7-16 for instructions.
7-20
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
2. When the printer is on and the Readymessage or the printerÕs
name appears in the front panel, press the Cleanbutton. The
printer displays the Þrst selection in the menu:
Clean:Light Stripes
<---- Clean Test
3. Press the left arrow (<---)button until the following front panel
message appears:
Clean:Ink Smears
<---- Clean Test
4. Press the Cleanbutton. The printer displays the following
message:
Warming Up
Cancel
5. After a short delay during the warm-up period, the printer begins
an automatic sequence of feeding 10 clean sheets of paper from the
media tray selected as the cleaning page source. A front panel
message indicates the number of sheets remaining to be fed. For
example:
Cleaning:Using 10 Sheets
6. When the cleaning sequence is complete, inspect the last sheet of
paper fed through the printer. If it is not clean, repeat the cleaning
sequence by pressing the Cleanbutton once again.
7. Return the printer to normal operation by pressing the Exit
button.
If the ink smear problem persists: Refer to the following two procedures for
directions on cleaning paper-feed rollers and the paper-exit path.
User Manual
7-21
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
Cleaning for jams and ink smears: paper-feed rollers
Approximate time to complete: 5 minutes
The paper-feed rollers carry the print media from the media tray and
manual-feed slot through the printer. Occasionally, stray ink particles
become attached to the paper-feed rollers, creating slick roller surfaces that
cause media to feed improperly. Clean the upper and lower paper-feed
rollers if either of the following conditions exist:
■
Media is consistently jamming behind the front cover or at the
manual-feed slot.
■
Ink smear problems persist after you have performed the
ÒCleaning for ink smears: internal paper pathÓ procedure.
9922-15
Refer to ÒUsing isopropyl alcoholÓ on page 7-19 for more information on
proper cleaning procedures.
Caution
Hot surfaces exist behind the upper paper-feed
rollers. To avoid personal injury during cleaning
procedures, do not reach in behind these rollers.
7-22
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
1. Open the front cover.
9922-123
2. Grasp the maintenance tray by the front edge and lift up while
sliding it out of the printer. Keep the maintenance tray upright.
9101-53
Note
Once the maintenance tray has been partially used, it leaks drum
fluid if tipped. Contact with the drum fluid poses no known
health risk; refer to page 11-6 for more information.
User Manual
7-23
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
3. Locate the two sets of upper paper-feed rollers above the
maintenance tray: One set of rollers is black rubber; the other set
is white plastic. Turning the lower rubber rollers also turns the
upper rollers.
4. To clean the upper black rubber rollers:
a. Use either the prepackaged alcohol-soaked cloth, or fold a
lint-free cloth into a 2-inch square and soak with alcohol.
Keep the cloth moist with alcohol during the procedure.
b. Place the cleaning cloth against the underside of each upper
rubber roller, lifting to create pressure against the roller.
c. Press the index or middle Þnger of your other hand ßat
against a lower roller and turn the roller toward you using the
entire length of your Þnger. The upper rubber roller should
rotate four or five complete revolutions to ensure proper cleaning.
9922-140
d. Scrub each roller thoroughly. If the cloth becomes dirty,
discard it and use another.
7-24
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
5. To clean the upper white plastic rollers:
a. Use alcohol-soaked swabs for this procedure.
b. Place the swab on top of each upper white roller and press
down on the swab to create pressure against the roller.
c. Rotate the upper white roller four or five complete revolutions by
turning the lower black rubber rollers away from you with the
index Þnger of your other hand.
9922-141
d. Scrub each roller thoroughly until clean. If the swab
becomes dirty, discard it and use another.
User Manual
7-25
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
6. Locate the two sets of lower paper-feed rollers: one set of rollers is
black rubber; the other set is white plastic. The lower rubber
rollers are located below the maintenance tray; the white plastic
rollers are located on the inside of the front cover.
7. To clean the lower rubber paper-feed rollers:
a. Use either the prepackaged alcohol-soaked cloth or fold a
lint-free cloth into a 2-inch square and soak with alcohol.
b. Place and hold the cleaning cloth on top of each lower rubber
roller, pressing to create pressure against the roller.
c. Press the index or middle Þnger of your other hand ßat
against a lower roller and turn the roller using the entire
length of your Þnger. The lower rubber roller should rotate
four or five complete revolutions to ensure proper cleaning.
9922-113
d. Scrub each roller thoroughly. If the cloth becomes dirty,
discard it and use another.
7-26
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
8. To clean the lower white plastic rollers:
a. Use either the prepackaged alcohol-soaked cloth or fold a
lint-free cloth into a 2-inch square and soak with alcohol.
b. Place and hold the cleaning cloth on top of each lower white
roller while turning the individual roller with your thumb and
foreÞnger.
9922-119
c. Scrub each roller thoroughly until clean. If the cloth becomes
dirty, discard it and use another.
9. Put the maintenance tray back in the printer, pushing on both
sides of the maintenance tray to latch it Þrmly in place.
10. Close the front cover.
If the problem persists: Refer to ÒCleaning for ink smears: paper-exit pathÓ on
page 7-28.
User Manual
7-27
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
Approximate time to complete: 10 minutes
If you have already performed the other ÒCleaning for ink smearsÓ
procedures described earlier in this chapter but problems persist, you should
manually clean the paper-exit path. Refer also to ÒCleaning for jams and ink
smears: paper-feed rollersÓ on page 7-22.
Occasionally, stray ink particles and drum ßuid become attached to the exit
Þngers, rollers, and guides under the exit cover causing ink streaks or marks
on the top edge, front, or back of prints. When this occurs, you must clean
these parts using both dry and alcohol-soaked swabs. Refer to ÒUsing
isopropyl alcoholÓ on page 7-19 for more information.
Sample ink smear: paper-exit path
9922-31
7-28
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
1. Open the front cover.
9922-138
2. Open the exit cover using the blue release button located inside
the front cover, at the top of the printer.
9922-24
User Manual
7-29
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
3. Clean excess ink particles and drum ßuid from the colored exit
Þngers by gently wiping the top surface of each Þnger using a dry
swab.
3
9922-114
Caution
To avoid damaging the print drum and exit fingers, never
scrape excess ink with a tool or fingernail. Use a dry swab
provided with the cleaning kit.
7-30
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
4. To clean the rubber exit rollers:
a. Wrap an alcohol-soaked cloth around the index Þnger of one
hand.
b. Press your cloth-covered Þnger against each roller and turn
the roller several times to clean each roller individually.
9922-115
Note
You may notice some staining of the exit rollers while performing
the cleaning procedure. This is normal and does not indicate
additional cleaning is necessary. Simply clean rollers to remove
any build-up of ink.
User Manual
7-31
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
5. To clean the white plastic exit rollers:
a. Wrap an alcohol-soaked cloth around the index Þnger of one
hand.
b. Place and hold your cloth-covered Þnger on top of each roller
while turning a black rubber exit roller toward you with
foreÞnger of your other hand.
9922-144
7-32
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
6. To clean the two sets of ribbed exit guides on the underside of the
exit cover, gently wipe the raised ribs using an alcohol-soaked
cloth.
Caution
To avoid damaging the print drum and exit guide, never scrape
excess ink with a tool or fingernail. Use only the materials
provided with the cleaning kit.
7. Close the exit cover and the front cover.
8. If the ribbed guides on top of the printer (the output tray) require
cleaning, use an alcohol-soaked wipe.
8
6
9922-116
User Manual
7-33
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
Cleaning for upper media tray jams: media-pick roller
Approximate time to complete: 5 minutes
Clean the media-pick roller if the printer incorrectly feeds paper or
transparencies or if it feeds more than one sheet at a time.
isopropyl alcohol. Refer to ÒUsing isopropyl alcoholÓ on page 7-19 for more
information on proper cleaning procedures.
The printerÕs front panel messages will guide you through the necessary
steps to perform this automatic cleaning procedure. You can also manually
clean the media-pick roller; refer to page 7-39.
Note
Media-picking problems can also occur when the maintenance
tray is not properly latched. Try removing and relatching the
maintenance tray to cure a media-picking problem. Refer to
“Replacing the maintenance tray” on page 7-11 for instructions.
Automatically cleaning the media-pick roller
1. When the printer is on and the Readymessage or the printerÕs
name appears in the front panel, press the Cleanbutton. The
printer displays the Þrst selection in the menu:
Clean:Light Stripes
<---- Clean Test
2. Press the left arrow(<----)button until the following front
panel message appears:
Clean:Media Tray Jams
<---- Clean Test
3. Press the Cleanbutton once again.
7-34
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
4. When the following front panel message appears, press Printif
you want a printout of the procedure, otherwise press Continue:
Print Instructions?
Continue Print
5. When you press Continue, a front panel message prompts you to
install the cleaning tray in the media tray.
a. Remove the upper media tray from the printer. Remove all
print media from the media tray.
9922-27
b. Remove the cleaning tray from the cleaning kit and open the
tray lid to reveal the cleaning tray sponge.
User Manual
7-35
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
c. Wet the cleaning tray sponge with isopropyl alcohol (
A); a
bottle is provided in the cleaning kit for dispensing the
alcohol. Alternately, you can squeeze the alcohol from two
presoaked alcohol wipe packets to moisten the cleaning tray
sponge (B).
A
B
9101-27
Caution
Rubbing alcohol may contain oils that leave undesirable
residue on printer parts. Carefully read the label on the
container. If the rubbing alcohol contains only isopropyl
alcohol and deionized water, it is safe to use. To avoid harming
the printer’s internal components, never use water only to
clean them.
7-36
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
d. Place the cleaning tray in the media tray so that the trayÕs
sponge pad is nearest the media trayÕs handle. Press the two
tabs underneath the cleaning tray into the two square notches
provided in the media tray.
9922-28
e. Insert the media tray with the cleaning tray into the printer.
6. Press the Cleanbutton. The printer cleans the media-pick roller
while displaying the following message:
Cleaning
7. When the cleaning operation is complete, the following front
panel message appears:
Remove Cleaning Tray
8. Remove the media tray from the printer.
9. Remove the cleaning tray from the media tray.
User Manual
7-37
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
10. Examine the separator pad located inside the media tray near the
paper trayÕs handle. If it is coated with dust, wipe the separator
pad using a clean cloth or a dry brush.
10
9922-142
11. Reload media in the media tray. Replace the media tray in the
printer.
12. The front panel redisplays the following message:
Clean:Media Tray Jams
<---- Clean Test
13. Press the Exitbutton to return to normal operation. Store the
cleaning tray in its original packaging for later use.
If media-feed problems persist: You may need to clean the media-pick roller by
hand with an alcohol-soaked cloth.
7-38
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
Manually cleaning the media-pick roller
1. Remove the upper media tray from the printer.
2. Open the front cover.
1
2
9922-23
Caution
Hot surfaces exist behind the upper paper-feed rollers. To
avoid personal injury during cleaning procedures, do not
reach in behind the paper-feed rollers.
User Manual
7-39
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
3. Grasp the maintenance tray by the front edge and lift up while
sliding it out of the printer. Place the tray on a level surface.
9101-53
Note
Once the maintenance tray has been partially used, it leaks drum
fluid if tipped. Contact with the drum fluid poses no known
health risk; refer to page 11-6 for more information.
7-40
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
4. To clean the top surface of the media-pick roller:
a. Locate the top of the media-pick roller behind the black rubber
paper-path rollers.
b. Use either the prepackaged alcohol-soaked cloth or a lint-free
cloth folded into a 2-inch square and soaked with alcohol.
c. Scrub the top surface of the media-pick roller thoroughly. If
the cloth becomes dirty, discard it and use another.
9922-25
5. Replace the maintenance tray in the printer.
Note
To prevent media jams at the media tray, be sure to push the
maintenance tray into the printer until both sides latch in place.
6. Close the front cover.
User Manual
7-41
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
7. To clean the bottom of the media-pick roller:
a. Use either the prepackaged alcohol-soaked cloth or a lint-free
cloth folded into a 2-inch square and soaked with alcohol.
b. Scrub the bottom surface of the pick roller thoroughly.
9922-17
8. Replace the upper media tray in the printer.
7-42
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring For Your Printer
7
Cleaning for lower tray jams: paper-pick rollers
Approximate time to complete: 1 minute
If the printer feeds paper incorrectly or feeds more than one sheet at a time
from the Lower Paper Tray Assembly, you can generally correct the problem
by cleaning the paper-pick rollers with isopropyl alcohol. Refer to ÒUsing
isopropyl alcoholÓ on page 7-19 for more information.
1. Remove the lower paper tray from the Lower Paper Tray
Assembly.
2. Locate the paper-pick rollers.
3. Using an alcohol-soaked cloth, scrub both paper-pick rollers
thoroughly.
3
2
9922-149
4. Replace the lower paper tray in the Lower Paper Tray Assembly.
User Manual
7-43
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Caring For Your Printer
7-44
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
8
Troubleshooting
Overview
even in high-volume printing environments. When printer problems do
maintenance will help keep your printer performing at its peak. This
■
■
■
■
■
■
■
ÒTroubleshooting quick referenceÓ on page 8-5
ÒLight stripes on prints: cleaning the printheadÓ on page 8-12
ÒMedia jams and misfeedsÓ on page 8-15
ÒInk smearsÓ on page 8-20
ÒIf your Þle doesnÕt printÓ on page 8-21
ÒPrinted colors are not what you expectedÓ on page 8-31
User Manual
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Front panel error messages
The front panel displays messages indicating the condition of the printer.
Some messages, such as Standbyand Warming Up, simply provide status
information and require no user action. Error messages, such as Jam:Open
Front Cover, require you to perform some action, such as clear a paper
jam. Refer to the table below for responses to front panel error messages.
Numeric error codes: The printer may display a numeric error code when it
detects certain types of problems. If you see a numeric error code, Þrst write
down the number. Then turn off the printer, wait at least 15 seconds, and
then turn the printer on again. If that does not solve the problem, call your
local Tektronix ofÞce for assistance or contact Tektronix Customer Support in
the U.S. and Canada at 1-800-835-6100 or on-line at
http://www.tek.com/Color_Printers/.
Front panel messages
Message
Action
Write down the error code in the display. Turn the
printer off, wait at least 15 seconds, and then turn the
printer on again. In the U.S., call Tektronix service at
1-800-835-6100. Outside the U.S., contact your local
Tektronix office.
Fault. Service
Required
An incorrect paper size is loaded in the tray, or paper
narrower than A4-size is in the manual feed slot. Use
letter- or A4-size media only.
Incorrect Media
Size
This message appears when the ink level drops to
one-half stick. Open the top cover and add the
appropriate color ink stick.
Ink Low
Open the top cover and make sure the bottom ink
sticks are resting against the bottom of the ink bin
chutes. Clean the ink sticks of particles from broken
ink sticks.
Ink Sticks Jammed
Insert a maintenance tray into the printer.
Install Tray (B)
Open the front cover, remove the maintenance tray,
and replace it with a new one.
Install New Tray
(B)
Open the exit cover and remove the paper jam. You
may need to clean the paper exit path if the problem
persists.
Jam:Open Exit
Cover
8-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Front panel messages (cont'd.)
Message
Action
Open the front cover and remove the paper jam from
the manual-feed slot or behind the front cover. You may
need to push on both sides of the maintenance tray to
relatch it or clean the upper or lower paper-feed rollers.
Jam:Open Front
Cover
There is a paper jam at the lower paper tray. Remove
the tray and the jammed paper.
Jam:Remove Lower
Tray
There is a paper jam at the standard media tray.
Remove the tray and the jammed paper. You may need
to run the Clean:Paper Jamsroutine if this problem
persists.
Jam:Remove Upper
Tray
Remove the media from the manual-feed slot and
reinsert it.
Jam:Retry Manual
Feed
Add paper to the lower paper tray.
Lower Media Tray
Empty
The maintenance tray is nearly empty of drum fluid.
Open the front cover, remove the maintenance tray,
and replace it with a new one.
Maintenance Tray
(B) Low
The printer requires a sheet of paper for self-cleaning,
but the media tray contains transparencies. Feed a
sheet of paper into the manual feed slot.
Manual Feed Paper
Add paper or transparencies to the media tray.
Media Tray Empty
Out of Ink
One or more ink bins is empty. Load the appropriate
ink stick(s).
Insert the lower paper tray.
Replace Lower
Media Tray
Insert the standard media tray.
Insert the standard media tray.
Replace Media Tray
Replace Upper
Media Tray
The printer has locked the maintenance tray because
hot ink is present. Close the front cover and wait for a
few minutes before trying to remove the maintenance
tray.
Tray (B) Locked
Unlock the transit restraint on the right side of the
printer before sending print jobs.
Unlock Transit
Restraint
User Manual
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Front panel messages (cont'd.)
Message
Action
Add paper or transparencies to the standard media
tray.
Upper Media Tray
Empty
Insert paper or transparency in the manual feed slot.
Waiting For Manual
Feed
The print job specifies paper, but the printer detects
that the transparency tray is installed switch on the side
of the tray is set to Transparency. Load paper in the
media tray and press OK. For printing paper, install
the paper tray and set the switch to Paper. For printing
labels in the transparency tray, set the switch to Label.
Waiting For Paper
The print job specifies transparency, but the printer
detects that the paper tray is installed. the tray switch
is set to Paper (paper tray) or Label (transparency tray).
Load transparency in the media tray and press OK. Pull
out the tray, set the switch to Transparency and reinsert
the tray.
Waiting For
Transparency
Open the front cover, remove the maintenance tray,
and empty the waste liner.
Waste Liner (A)
Full
8-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Troubleshooting quick reference
Refer to the following tables if you encounter problems with the printer. For
additional troubleshooting topics, visit the Tektronix web site at
http://www.tek.com/Color_Printers/.
Media feeding or jamming problems
Symptom
Paper jams or mispicks
at the standard paper
tray or transparency tray.
■ Is the paper too thick or thin for the printer? Use standard
2
office paper 60 to 120 g/m (16 to 32 lb.) or Tektronix
transparency media. Refer to “Acceptable media sizes,
types, and weight” on page 4-6 for more details on the
type of paper you can use with the printer.
■ Do not load the tray beyond the fill line. Paper tray
Transparency tray capacity is 175 sheets transparency.
latched firmly into place.
■ You may need to clean the media-pick rollers. Refer to
“Cleaning for upper media tray jams:media-pick roller” on
page 7-34.
2
Paper-feed problems at
the Lower Paper Tray
Assembly.
■ Use standard office paper only, 60 to 120 g/m (16 to
32 lb.).
■ Do not load the tray beyond the fill line. Paper tray
2
capacity is 625 sheets of 90 g/m (24 lb.) paper.
Paper jamming inside
the printer.
■ Remove and relatch the maintenance tray. Refer to
“Replacing the maintenance tray” on page 7-11.
■ You may need to clean the paper-feed rollers. Refer to
Paper jamming at
manual feed slot.
■ Wait until the front panel prompts you before inserting
media into the manual feed slot. Feed the paper or
transparency into the manual feed slot and let the printer
take the media out of your hands.
■ Select Manual Paper or Manual Transparency in the
printer driver.
■ Select the appropriate size media in the printer driver.
■ Make sure to align the paper against the left edge of the
manual feed slot.
■ Is the paper too thick or the wrong size for manual feed?
Refer to “Acceptable media sizes, types, and weight” on
page 4-6.
User Manual
8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Image Quality Problems
Symptom
Solution
Light-colored or blank
stripes on prints.
■ Refer to “Light stripes on prints: cleaning the
printhead” on page 8-12.
Ink streaks or oil on front, ■ Do not print on both sides of the media. Ink may be
back, or edges of print.
offset onto the internal paper path.
paper path” on page 7-20.
Transparency print
quality poor.
■ Use Tektronix premium transparency media.
■ Make sure that you have selected Standard as the
print-quality mode; try setting Vivid Color as the color
correction.
Make sure that the switch on the side of the paper or
“Transparency quality tips” on page 4-15.
Print is wrinkled.
■ You may be using paper that is too thick or thin. Refer
to “Acceptable media sizes, types, and weight” on
page 4-6.
Paper edge is rippled.
■ You may be using paper with the wrong grain. Load
long-grained paper.
Printed image is shifted
or the wrong color, or the
margins are not correct.
■ You may have to make adjustments in the application
or print driver. Refer to “Printing and installation
problems” on page 8-8.
■ Make sure that the paper is not curled. Also refer to
“Cleaning for jams and ink smears: paper-feed rollers”
on page 7-22.
■ Microsoft PowerPoint users:
■ Macintosh users: In the Chooser, set Background
Printing to Off.
■ PC users: Through the Print Manager, turn off
background printing.
8-6
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Image Quality Problems (cont'd.)
Symptom
Solution
Colors do not print as
expected.
transparency tray is set for the type of media on which
you are going to print.
■ Refer to “Adjusting the color of your prints” on page 5-2
loaded in a paper tray but did not selectTransparency
as the tray selection or paper source in the printer
driver. Refer to “Printing transparencies” on page 4-13
for more information.
■ Refer to “Printed colors are not what you expected” on
■ Refer to “Printing and using the color sampler charts”
on page 5-6.
Image prints in black-
and-white instead of
color.
■ PC users: Be sure to use a driver that supports color
page 4-19 for information on drivers.
■ Microsoft Excel users: In the Print dialog box, check
the Print using color option.
■ Macintosh users: Use a supported color PostScript
printer driver and the Phaser 360 printer’s PPD file. In
the Print Options dialog box, select Color/Grayscale.
Refer to page 4-35 for more details on how to print from
a Macintosh.
■ You may need to install application-related files such as
a PDF or PPD file for QuarkXPress.
■ PC users: Refer to “PC/Windows software” on
page 3-2 for information.
■ Macintosh users: Refer to “Mac OS software” on
page 3-16 for information.
■ You may have incorrectly sent the Monochrome color
correction utility file to the printer. Send another color
correction utility file to the printer, use a front panel
selection, or print from a driver.
User Manual
8-7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Printing and installation problems
Symptom
Solution
You have problems
printing from a specific
application.
■ Get information and tips on printing from specific
applications (such as QuarkXPress and PageMaker)
from theTektronix Color Printer web site and from HAL,
another Tektronix information resource. Refer to
“On-line support” on page 9-1 and “Getting information
by fax” on page 9-3.
Fonts print incorrectly in ■ Make sure you have installed the correct printer with
Windows.
your driver. Refer to “PC/Windows software” on
page 3-2 for instructions on installing drivers.
Text prints in Courier
font.
■ The font you have specified is not available. The
Phaser 360 printer has 164 resident fonts. Other fonts
must be downloaded or available on a SCSI hard disk.
Refer to “Downloading fonts” on page 5-13.
The image does not
finish printing (the printer
times out).
■ PC users: If you are using the parallel port, use the
MODE command to set the PC’s communication
parameters, for example: MODE LPT1:,,P (for parallel
port LPT1).
■ Windows users: Double-click on the Control Panel.
Double-click the Printers icon. Choose your Tektronix
printer. Click the Connect button. Change the
Transmission Retry to 850.
■ Parallel port printing: If you get a timeout from the
Connect dialog box, change the Ports selection from
The area of paper that
the printer prints on is
smaller than the media
size.
■ See “Margins and image area” on page 4-7 for more
adjust the margins in your application software.
Ink Lowor Ink
■ Apply pressure to each row of ink sticks in the loading
Sticks Jammed
message appears when
ink bins are full.
bin to make sure they are not jammed.
A Macintosh printed
image has shifted or the
margins are not correct.
■ You should install a supported printer driver and the
Phaser 360 printer PPD onto your Macintosh to select
the correct page sizes from the driver. Refer to “Using
the Mac OS installer” on page 3-17 for information.
■ Turn off Background Printing through the Chooser.
■ Refer to “Printing from a Macintosh” on page 4-35 for
details on how to print from a Macintosh.
8-8
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Printing and installation problems (cont'd.)
Symptom
Solution
The Readymessage or
the printer’s name is
displayed, but the file
does not print.
■ Make sure that the Phaser 360 printer is the selected
printer. Try printing the same file to another PostScript
printer. If the file prints, then the problem could be with
adapters” on page 10-7 for information on ordering
Tektronix interface cables.
■ Turn the printer’s power off, wait at least 15 seconds,
and then turn the power on again.
Handler to determine the cause of the problem.
The printer takes too
long to warm up (more
than 30 minutes).
is not blocked. Allow at least 5 cm (2 in.) clearance on
each side of the printer.
A file does not print and
a virtual memory (VM)
error appears.
■ You may need to expand printer memory. Refer to
“Memory upgrade” on page 10-5 for more information.
A file does not print, or it ■ Make sure that the printer is set up to receive the
prints unexpected data.
appropriate language (PostScript, HP-GL, or PCL5) for
that file. Refer to “Checking the printer’s language
mode” on page 8-25 for more information.
The printout is delayed.
■ See “Printer standby modes” on page 6-8.
The printer outputs two
prints after a jam is
cleared.
■ The printer is cleaning the print drum and reprinting the
image. Refer to “Media jams and misfeeds” on
page 8-15.
Files sent during
power-up do not print.
■ Before printing a file, wait until the printer’s front panel
displays Readyor the printer’s name.
The printer receives a file ■ Do not set the wait timeout to 0.
on the parallel port but
does not print.
■ Print files should not have extra characters after the
End-of-Job character (Ctrl-D).
Refer to the on-line manual on the printer’s CD-ROM for
information on setting timeouts and the Ctrl-D character.
User Manual
8-9
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Printing and installation problems (cont'd.)
Symptom
Solution
The printer receives a file ■ Do not set the wait timeout to 0.
on the parallel port. The
■ Print files should not have extra characters after
front panel displays
Processing Data
indefinitely. Another file
sent to a different port
causes your computer or
network interface to lock
up.
the End-of-Job character (Ctrl-D).
Refer to the on-line manual on the printer’s CD-ROM for
information on setting timeouts and the Ctrl-D character.
The printer receives a file ■ To recover, press the Wakeupor Cancelbutton or turn
on the parallel port and
the job prints
successfully. After
printing, the printer
displays Processing
Data, goes into Standby
mode, but doesn’t come
out of Standby mode for
the next print job.
the printer’s power off, wait at least 15 seconds, and
turn the power on again. (If you reset the printer, you
must send the print job again.) To prevent this
condition, do not set the wait timeout to 0.
■ Print files should not have extra characters after the
End-of-File character (Ctrl-D).
Refer to the on-line manual on the printer’s CD-ROM for
information on setting timeouts and the Ctrl-D character.
The Startup Page prints ■ If the printer detects a nonfatal error at power-up, the
although you disabled it.
Startup Page prints, even if you have disabled it. A red
box on the Startup Page identifies the type of error.
The printer’s power-up self-test can detect problems
inoperable. Examples of these nonfatal errors include
faulty printer ports and some memory failures. The
printer may require service.
The maintenance tray is The printer locks the maintenance tray until it has cooled
locked inside printer.
down. Try the following:
■ Close the front cover, wait for a few minutes, and try
removing the tray again.
■ Turn the printer off, wait for about 1 minute, and then
turn the printer back on. Wait for about 2 minutes, then
try removing the maintenance tray again.
The front panel displays ■ You may need to install a new maintenance tray. Refer
Busy Melting Ink
and will not return to
Ready.
to “Replacing the maintenance tray” on page 7-11.
■ Make sure that the ink stick bins are fully loaded. Fill
the bins if necessary. Turn the printer off, wait
60 seconds, then turn the printer back on. Wait until
the front panel displays Ready(about 15 minutes).
8-10
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Network problems (Macintosh)
Symptom
Solution
The printer doesn’t
appear in the Chooser
on a Macintosh.
■ Make sure the printer is connected to your network. If it
is not, turn the printer off before reconnecting it.
■ Check the termination; refer to the documentation for
your network adapter or connector for information on
termination.
■ Check the Configuration Page to get the zone name
and printer name. Refer to “Printing a Configuration
Page” on page 2-25. Make sure that the correct zone
and printer name have been selected in the Chooser.
■ Make sure that the correct network is selected in the
Network Control Panel.
User Manual
8-11
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Light stripes on prints: cleaning the printhead
Approximate time to complete: 10 minutes
Symptom: Prints have narrow, lengthwise stripes that are faded or the
wrong color, or prints have missing colors.
Solution: Run the automatic printhead-cleaning sequence from the printerÕs
front panel.
9682-21
1. When the Readymessage or the printerÕs name appears, press the
Cleanbutton. The printer displays the Þrst selection in the menu:
Clean:Light Stripes
<---- Clean Test
2. Press the Cleanbutton again.
3. A series of front panel messages indicate the condition of the
printer as it progresses through a sequence of automatic cleaning
routines. The printer outputs a Cleaning Page (see page 7-16) at
the end of the cleaning sequence that you may discard as normal
ofÞce waste.
4. When the cleaning sequence is completed, the printer displays the
following message:
Clean:Light Stripes
<---- Clean Test
8-12
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
5. To conÞrm that the problem has been corrected, press the Test
button to print a Test Page. Check for any missing color bars on
the Test Page. The following illustration shows a correct Test Page
and an example of a Test Page with a missing color bar.
■
If your Test Page looks like the Þrst example, go to Step 8 to end this
procedure.
■
If your Test Page looks like the second example with a missing color
bar, go to Step 6 to perform the cleaning procedure again.
1
Black
2
Cyan
3
Magenta
4
Yellow
1
2
3
4
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
6
6
6
6
7
7
7
6725 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
8
9 10 11 12 13
8
8
8
9
9
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
1
2
3
4
5
6
6725 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
8
10 11 12 13
9682-22
User Manual
8-13
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
6. If one or more of the color bars are still missing or are light, repeat
the cleaning sequence by pressing the Cleanbutton again. When
cleaning ends, the printer outputs a Cleaning Page that you may
discard as normal ofÞce waste.
7. If the second cleaning sequence does not cure the light stripes or
missing colors problem, press the Cleanbutton to repeat the
cleaning sequence.
Note
The third cleaning sequence implements a more extensive
cleaning of the printer, which may take longer for the printer to
execute than the previous two cleanings.
8. If your prints still have color stripe problems after the third
cleaning sequence, turn the printer off for at least 8 hours to allow
the ink to solidify. When the printer is turned back on, it will
perform a self-cleaning routine that should resolve the problem.
9. If your prints still have color stripe problems, service may be
required.
10. Return the printer to normal operation by pressing the Exit
button until the Readymessage appears.
8-14
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Media jams and misfeeds
After you clear a media jam: The printer automatically outputs a second,
usually partial print to remove any image that may remain on the print
drum and then prints your original image.
The upper tray is the default tray for media the printer uses in self-cleaning.
If you have a Lower Paper Tray Assembly, you can make it the default tray
through the printerÕs front panel menu. Select Printer Defaults:
Cleaning Page Sourceand make your tray selection.
Preventing media jams
Use the following guidelines to prevent media jams inside the printer.
■
When inserting a maintenance tray, after sliding it into the printer,
use both thumbs on the front edge of the tray to push the tray in to
latch it.
■
■
■
Periodically clean the printer to keep it in peak condition.
Fan paper before loading it in the upper and lower trays.
Use standard grade paper, 60 Ð 120 g/m2 (16 Ð 32 lb.); use the
manual-feed slot for heavier stock, up to 220 g/m2 (80 lb.). Do not
use three-holed paper, perforated paper, legal-size paper, or
envelopes.
■
Wait until a front panel message prompts you before feeding a
second sheet of paper or transparency into the manual-feed slot.
■
■
Keep paper and other supplies clean and free from dust.
Paper that has been sitting out of its sealed wrapper can become
distorted, causing paper jams. Keep paper sealed until you are
ready to use it for printing.
■
Do not use paper that has been creased or wrinkled.
Caution
Never attempt two-sided or two-pass printing. Ink already present
on the media will offset onto the internal paper path, requiring you to
perform cleaning procedures. Excessive buildup of ink in the paper
path may cause paper jams.
User Manual
8-15
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Locating jammed media
Paper jams can occur in these places:
1. Inside the exit cover, around the large black (transÞx) roller
2. Inside the front cover
3. At the manual feed slot
4. At the standard media tray
5. At the Lower Paper Tray Assembly
1
2
3
LETTER
A4
5
4
9922 -30
Caution
Some surfaces inside the printer may be hot. Be careful not to
touch the areas marked with this caution icon:
8-16
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Clearing a media jam
■
To avoid ink smearing inside the printer, always try to pull
jammed paper or transparencies out through the top of the printer.
Use both hands to gently pull the media through its normal path
out the top of the printer (exit cover), if possible. Do not use
excessive force pulling the media; it may tear.
■
■
■
After removing the jammed media, inspect it for tears. Leave no
media scraps in the printer.
If your prints have ink smears after clearing a jam, refer to
ÒCleaning for ink smears: paper-exit pathÓ on page 7-28.
If jamming persists, cleaning the printer may solve the problem.
Refer to ÒCleaning for ink smears and jams: internal paper pathÓ
on page 7-20.
Warning Never use a sharp object to remove jammed paper. You may
damage the print drum, requiring repair to your printer.
User Manual
8-17
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
1. Check for jammed media that has partially exited through the top
of the printer. Remove any jammed media by pulling the media
gently out from the exit cover.
2. If necessary, open the exit cover using the blue release button
located inside the front cover, at the top of the printer.
9922-24
3. Using both hands, pull the jammed media from the top of the
printer.
9922-60
8-18
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
4. If the jam has not cleared, open the front cover and check for
jammed media inside the printer.
9922-123
5. If necessary, remove the media tray to locate and clear jammed
media.
9922-139
User Manual
8-19
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Ink smears
Symptom: Prints have stray ink marks on the front or the back.
Solution: Clean the internal paper path. If smears persist, clean the
paper-feed rollers. If smears still appear, clean the paper-exit path.
1
2
3
See ÒCleaning for ink smears and jams: internal paper pathÓ on page 7-20.
See ÒCleaning for jams and ink smears: paper-feed rollersÓ on page 7-22.
See ÒCleaning for ink smears: paper-exit pathÓ on page 7-28.
1
2
3
9922-29
8-20
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
If your file doesn’t print
If you've conÞgured a supported driver for your printer but your printer
isn't printing, try the following suggestions. If these suggestions fail to solve
the problem, copy the Tektronix PostScript error handler utility to your
printer to determine what is wrong. Refer to ÒUsing a PostScript error
handlerÓ on page 8-27 for information on using the error handler.
General things to check for
Macintosh users
■
Open the Chooser and select a supported driver, such as the
LaserWriter 8.x, and your printer.
■
If the driver isnÕt installed or properly set up with your printer,
refer to ÒMac OS softwareÓ on page 3-16 for instructions.
■
■
Make sure that Background Printing is turned off.
Close the Chooser and try printing again.
■
■
If you are having trouble printing from the Finder in System 7.1,
for example, if the driverÕs dialog boxes are not opening, it may be
because the Finder doesnÕt have enough allocated memory.
Reinstall a supported driver to automatically allocate enough
memory for printing from the Finder.
For PCI-based PowerMacs, you should be using the latest version
of Open Transport, available from Apple Computer.
User Manual
8-21
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Windows users (general)
■
Check to make sure that you have conÞgured the communications
ports and the Handshake option correctly by printing the
ConÞguration Page. Refer to ÒPrinting a ConÞguration PageÓ on
page 2-25.
■
Make sure that you are using the correct cables for your computer
and printer. See ÒInterface cables and adaptersÓ on page 10-7 for
cable information.
Windows 3.1 users
■
Make sure that your printer is connected to the port you selected
in the driverÕs Printers/Connect dialog box.
■
Check the Options dialog box to make sure that Printer, not
Encapsulated PostScript File, is selected in the driverÕs
Print To box.
■
If the error message Windows Header has not been
downloaded to the printerappears on your computer
screen, go to Setup, click the Job Control tab, and click one of the
options for PostScript Header. Refer to ÒJob Control tabÓ on
page 4-30 for details on the Job Control tab.
Windows 95 users
■
■
■
Make sure that your printer is connected to the port you selected
in the driverÕs Details tab.
Make sure that the correct port is selected in the driverÕs
Details tab.
If the error message Windows Header has not been
downloaded to the printerappears on your computer
screen, click the PostScript tab and click one of the options for
PostScript Header. Refer to ÒPostScript tabÓ on page 4-24 for
details on the PostScript tab.
8-22
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
If you are using PC/NFS
If you have PC/NFS software installed on your computer, you need to make
the following selection in the Network Options dialog box:
1. From the Main window, double-click the Print Manager icon.
2. From the Options menu in the Print Manager, select
Network Settings.
3. In the Network Options dialog box, uncheck the
Print Net Jobs Direct box.
4. Click OK.
If you can’t print from Windows to an LPT port
Windows 3.1
If your printer is connected through an LPT (parallel) port and your
document doesnÕt print, try the following:
1. In the Control Panel, double-click the Printers icon.
installed printers.
3. Click the Connect button; the Connect dialog box appears.
4. Change your computerÕs port connection from LPTx to
LPTx.DOS (where x is 1, 2, or 3).
5. Click OK.
Note
Refer also to “Fixing timeout problems in Windows” on
page 8-28 for instructions on fixing timeout problems.
User Manual
8-23
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Windows 95
1. In the taskbar on your screen, select Start.
2. In the menu that appears, select Settings.
3. In the next menu, select Printers; the Printers window appears.
4. From the File menu, click your printerÕs icon and select
Properties.
5. Click the Details tab.
6. Click Add Port.
7. Click Other.
8. Make sure that Local Port is highlighted, then click OK.
9. Type LPTx.DOS (where x is 1, 2, or 3).
10. Click Apply, then click OK.
11. In the Details tab, the Print to the following port should be
LPT.DOS (unknown local port).
8-24
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Checking the printer’s language mode
If your Þle doesnÕt print, the language on the printerÕs port you are using
may have been changed.
1. Print a copy of the printerÕs ConÞguration Page to see the
language mode on each port. Refer to ÒPrinting a ConÞguration
PageÓ on page 2-25.
2. If the printer port you are using has the wrong language set for the
type of application you are using, send one of the following utility
Þles to the printer:
■
To print PostScript Þles, use the PSCRIPT.PS Þle to set up a port to
receive PostScript. Refer to the on-line manual on the printerÕs
CD-ROM for details.
■
To print PostScript, HP-GL, or Monochrome PCL5 Þles
interchangeably, use the AIS.PS Þle to set up a port for automatic
language selection. Refer to the on-line manual on the printerÕs
CD-ROM for details.
User Manual
8-25
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
PostScript printing errors
If you get a PostScript error when printing from Aldus PageMaker, Aldus
FreeHand, QuarkXPress, or Canvas, you may be using an older or incorrect
version of the printer description Þle.
1. You should always use the most current printer description Þle.
To determine the date of the Þle you are using, do the following:
■
Mac OS users:
Select (highlight) a printer description Þle. From the File menu,
choose Get Info. Make a note of the version date. Or, open the
Descriptions folder to Þnd the Þle name and date.
■
■
Windows 3.1 users:
In the File Manager, open the Windows folder, then the Phsrmtch
folder. Make a note of the version date of the Þle.
Windows 95 users:
In Windows Explorer, select the Phsrtool directory. Check a printer
description ÞleÕs creation date. Make a note of the version date.
2. Check TektronixÕ on-line services to see if the printer-related Þles
you have are the most recent. Refer to ÒOn-line supportÓ on
page 9-1 for information on TektronixÕ on-line services and
ÒReceiving email update noticesÓ on page 9-1.
8-26
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Using a PostScript error handler
The PostScript error handler is useful for diagnosing problems when a job
doesnÕt print. PostScript errors are printed on a page with other status
information when an error occurs. This function can be useful to
programmers for debugging PostScript code.
You can enable and disable the error handler through the printerÕs front
panel menu (Printer Defaults menu), through PhaserLink software (refer to
the PhaserShare Networking System Administrator Manual), or through a
PostScript utility Þle (refer to the printerÕs CD-ROM).
Once youÕve enabled the error handler through the front panel or through
PhaserLink software, the error handler remains active until you manually
disable it. Cycling the printerÕs power does not disable the error handler. If
you use a PostScript utility Þle to enable the error handler, you can disable it
by cycling the printerÕs power.
User Manual
8-27
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Fixing timeout problems in Windows
If print jobs are timing out and not printing, you may need to increase the
timeout values in Windows and in the printer. Try one of the following
procedures to change the Windows timeout. If the Windows procedure
doesnÕt work for you and you are not on a network, try the DOS procedure.
Then, follow the procedure to change the printerÕs timeout.
Windows timeout: From Windows 3.1
1. From the Main menu, open the Control Panel.
2. Double-click the Printers icon to open the Printers dialog box.
3. Click your printerÕs icon.
4. Click the Connect button to open the Connect dialog box.
5. Increase the Transmission Retry to 950 seconds by typing in the
new number.
6. Click OK.
Windows timeout: From Windows 95
1. In the taskbar on your computer screen, click the Start icon; a
menu appears.
2. Move the cursor over Settings; another menu appears.
3. In the menu, click Printers; the Printers window appears.
4. In the Printers window, select the Phaser 360 printer icon. From
the File menu, select Properties.
5. Click the Details tab and increase the Transmission Retry to
999 seconds (or higher).
6. Click Apply, then click OK.
8-28
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Windows timeout: From DOS (and Windows 3.1)
Note
To use this procedure, the printer must be connected directly to
your computer and not on a network.
1. At the DOS prompt, issue the DOS MODE command by typing
the following:
MODE LPT1:,,P
2. Start Windows 3.1.
3. From the Main menu, open the Control Panel.
4. Double-click the Printers icon to open the Printers dialog box.
5. Click the Connect button to open the Connect dialog box.
6. Change the port selection from LPT1 to either LPT1.DOS or
LPT1.OS2, depending on the options you see in the dialog box.
7. Click OK.
User Manual
8-29
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Printer’s timeout
Note This is the basic procedure for changing one of the printer’s
timeout values. For more information on the printer’s timeouts,
refer to the on-line manual on the printer’s CD-ROM.
and wait timeout values. When sent to the printer, your edited version of
the TIMEOUTS.PS Þle changes the values in the printer, but only while the
printer is turned on; if the printer is turned off or reset, the values return to
their defaults. To restore your desired timeout settings, you must send your
edited TIMEOUTS.PS Þle to the printer again.
Note
The TIMEOUTS.PS file affects printer operation. If the printer is
shared on a network, using this file may affect the prints requested
by other users.
1. Follow the instructions beginning on page 3-1 to install drivers
and printer software.
2. Locate the PHSRTOOL directory, created on your computerÕs hard
disk by the printerÕs installer. In the PHSRTOOL directory, locate
the PHSR360 subdirectory, and then locate the TIMEOUTS.PS Þle.
3. Using a text editor, open the Þle. The default value is 40 seconds
for the wait timeout. Change the value in the WaitTimeOut line
to 999.
4. Send the TIMEOUTS.PS Þle to the printer:
■
PC users: Use the DOS COPY command. (Windows 3.1 users can
also use the Copy command in the File Manager.)
■
Workstation users: Send the Þle to the printer as you would any
PostScript Þle.
8-30
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Printed colors are not what you expected
For information on selecting TekColor color corrections for accurate color
reproduction, see ÒAdjusting the color of your printsÓ on page 5-2.
■
■
Select another Color Correction option and print your image
again.
If you are not using a supported driver (installed from the
printerÕs CD-ROM) and are sharing the printer with other users
on a network, another user may have changed the printer's color
■
If you use the driver's Use Printer Setting option and printed
colors are not what you expected, check the following:
■
■
A selection may have been made in the TekColor Correction
menu on the printer's front panel. These settings change the
printer's color correction setting.
A color correction utility Þle may have been downloaded to the
printer. These Þles change the printer's color correction setting.
See also ÒSharing the printer on a networkÓ on page 8-34.
User Manual
8-31
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Printing PANTONE Colors
If the Phaser 360 printerÕs printer-speciÞc PANTONE Colors are not printing
as expected, make sure that you are printing with the Enhanced
print-quality setting and with color corrections set to None. Refer to
ÒPrinting the PANTONE Color ChartÓ in the on-line manual on the printerÕs
CD-ROM for more information.
There are many variables in process reproduction of colors generated by the
Phaser 360 printer, any one of which may affect the quality of the PANTONE
Color simulation, including:
■
■
■
■
Type of ink used on printing press
Type of ink Þlm used on printing press
Effective Þnal resolution
Dot structure/halftones
Note
The Phaser 360 color printer is PANTONE-approved only when
If you have questions about PANTONE Color Matching, you can get
information in the following places:
■
Tektronix web site: You can view selected topics on the Phaser 360
web address:
http://www.tek.com/Color_Printers/userdoc/introduction.html
■
HAL: Request a document catalog from HAL, the Tektronix fax
library. Refer to ÒGetting information by faxÓ on page 9-3 for
instructions on using HAL.
Blue colors look too purple
If printed blue colors look too purple, print your document with the
Vivid Color color correction. Refer to ÒTekColor correction descriptionsÓ on
page 5-3 for more information on the Vivid Color color correction.
8-32
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
User Manual
8-33
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Sharing the printer on a network
Prints do not reflect your settings
If you share a Phaser 360 printer with other users on a network, the
following two conditions may affect your prints:
■
■
Another user has downloaded a color correction utility Þle.
Someone has made color correction settings at the printerÕs front
panel.
You can override those settings if you are printing from a supported driver
by making sure that your color correction mode is set to any of the selections
except Use Printer Setting. If you are printing from a nonsupported driver,
you will need to either send a color correction utility Þle to the printer or
change the printerÕs settings at the front panel.
If the colors on your prints are still not what you expected, and your system
administrator has disabled some of the printerÕs front panel menus, ask
what settings are in effect and whether a color correction utility Þle has been
downloaded to the printer. You can also print a ConÞguration Page to see
the current color correction selection; see ÒPrinting the Help PagesÓ on
page 6-7 for instructions.
If the Apple Printer Utility does not work
The Apple Printer Utility cannot be used if the printer is connected to a print
server. See your system administrator to temporarily remove the printer
from the print server to download any of the PostScript utility Þles.
8-34
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
9
Customer Support
On-line support
Visit our color printer web site for more information about your printer. For
example, view updated user documentation, download utility Þles, get
answers to frequently asked questions, Þnd a list of Tektronix dealers in your
area, or contact customer support.
Tektronix Color Printer
web site
www.tek.com/Color_Printers/
Documentation
www.tek.com/Color_Printers/userdoc/introduction.html
www.tek.com/Color_Printers/support/colcare.html
ftp.tek.com/Color_Printers/
Technical support
Anonymous FTP server
Email update notices
www.tek.com/Color_Printers/support/subscribe.html
Receiving email update notices
Register your printer on-line and sign up to receive notiÞcation by email of
new printer drivers, accessories, and upgrades for your Tektronix Phaser
color printer. To subscribe to this free service, follow these steps:
1. Point your web browser to the Tektronix web site:
http://www.tek.com/Color_Printers/support/subscribe.html
2. From the pull-down list, enter your email address and select your
model of Phaser color printer.
3. Click the subscribe button.
User Manual
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Customer Support
Customer Support Centers
For more information or for getting help with troubleshooting or servicing
your printer, contact your local Tektronix dealer or sales representative or
the following resources worldwide:
Customer Support Centers
U. S. and Canada
1-800-835-6100
(Monday through Friday
6:00 am to 5:00 pm PST)
Japan
Australia
81 3 3448 4872
1 800 811 177
Korea
Austria
82 2 528 5299
0 660 5804
Luxembourg
0800 2853
Belgium
0800 1 5059
Norway
800 11782
Brazil
0800 16 0220
Singapore
65 356 3900
Denmark
80 01 81 76
Spain
900 97 4499
Eastern Europe/Middle East
+44 1908 68187
Sweden
020 795 177
Finland
0800 1 14494
Switzerland
155 9493
France
05 90 85 41
Taiwan
886 2 765 6362
Germany
0130 82 10 68
The Netherlands
06 0221647
Hong Kong
852 2585 6688
UK
India
0800 558668
91 80 225 2996
Italy
1678 77261
All other locations: Contact local Tektronix dealers or
Tektronix offices. For a list of dealers in your area, visit
our web site: http://www.tek.com/Color_Printers/.
9-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support
9
Getting information by fax
Another Tektronix resource for up-to-date information is HAL (Highly
Automated Library). If you have a fax machine and a touch-tone telephone,
you can quickly receive by fax the latest technical hints and tips, solutions to
common technical problems, and application notes for software problems
(such as CorelDRAW! and QuarkXPress).
You may call HAL from anywhere in the world, and it is available 24 hours a
day, seven days a week. For a catalog listing HAL documents, call one of the
numbers below.
Note
Not all documents are available in all languages. If a local version
of the document you want is available, HAL will send it in your
language. Otherwise, it will send an English document.
Country
Numbers
U.S., Canada
1-800-835-6100 (inside U.S. and Canada)
(503) 682-7450 (outside U.S. and Canada)
1-800-650-633 (toll free)
Australia
02 9878 0332
Austria
Belgium
Denmark
Finland
Holland
Italy
00 44 1908 681839
Norway
Switzerland
France
0800 90 81 86
Germany
Spain
0130 819 220
07 44 1908 681839
009 44 1908 681839
01908 681839
Sweden
UK
Other countries
+44 1908 681839 (where + is your country’s
International Access Code)
User Manual
9-3
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Customer Support
9-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
10
Supplies, Accessories,
and Expanding Your
Printing System
Tektronix printers and Tektronix supplies:
®
Made For Each Other
Tektronix supplies are developed and tested as a total system: printer,
user-replaceable components, and media. These system components work
together to produce consistent, high-quality color images.
Always order Tektronix supplies for your Phaser 360 printer to guarantee
the best print quality, media feed reliability, and trouble-free printer
performance.
Customizing your printer
Tektronix offers upgrades and accessories to expand your printerÕs
capabilities. To order, refer to the information provided here or the printer
supplies sheet that was shipped with the printer and contact your local
dealer or Tektronix ofÞce. In the United States, contact your local dealer or
call Tektronix at 1-800-835-6100.
User Manual
10-1
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Supplies, Accessories, and Expanding Your Printing System
Printer supplies
For a complete list of printer supplies, refer to the supplies information sheet
that was shipped with the printer and contact your local dealer or, in the
United States, call Tektronix at 1-800-835-6100.
Supplies
Order number
016-1307-00
016-1308-01
016-1309-01
016-1310-01
016-1361-00
016-1362-00
016-1359-00
016-1360-00
016-1130-00
016-1131-00
016-1368-00
016-1369-00
436-0294-03
436-0299-00
016-1341-00
Description
Phaser 340/350/360
Free black sticks
®
ColorStix ink sticks
Cyan (3), includes free black sticks
Magenta (3), includes free black sticks
Yellow (3), includes free black sticks
Letter-size premium* (50 sheets)
A4-size premium* (50 sheets)
Letter-size standard (50 sheets)
A4-size standard (50 sheets)
Letter-size (50)
Tektronix transparencies*
Transparency sleeves
Tektronix paper
A4-size (50)
Letter-size, 90 g/m2 (24 lb.) (500 sheets)
A4-size, 90 g/m2 (24 lb.) (500 sheets)
Includes waste liner
Maintenance tray
Waste liner
(pack of 5)
Cleaning kit
Includes cleaning tray, alcohol wipes,
foam swabs, bottle
Lint-free alcohol-soaked cleaning 006-7824-01
wipes
(pack of 10)
Phaser 360 Printer User Manual
070-9922-0102
Available also in French (-1011), Italian
(-2021), German (-3031), and Spanish
(-4041)
PhaserShare Networking System 070-9789-00
Administrator Manual and
diskettes
Includes documentation and utility files
for setting up and configuring the printer
on a network
Phaser 360 Printer Drivers and
Utilities diskette set
063-2936-0001
Phaser 360 Printer CD-ROM
063-2937-0002
Includes user documentation, drivers
and utilities, and other files
* Tektronix premium transparencies offer enhanced ink adhesion and superior print quality.
10-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplies, Accessories, and Expanding Your Printing System 10
PhaserShare network cards
The Phaser 360 printer is shipped with a built-in 10BaseT Ethernet port and
an expansion slot for an additional network interface. Tektronix
PhaserShare¨ network cards are easy to install and offer high-performance
network connectivity, simultaneously supporting different network
protocols.
Description
Order number
Fast Ethernet (100BaseTx/10BaseT/10Base2 card): includes ZNBFE
support for Novell NetWare, EtherTalk, TCP/IP, Telnet, FTP,
and HTTP
Token Ring card: includes support for Novell NetWare,
TokenTalk, TCP/IP, Telnet, FTP, and HTTP
ZNBTR
ZNBLT
LocalTalk/Serial card
User Manual
10-3
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Supplies, Accessories, and Expanding Your Printing System
Media trays
Paper and transparency trays
The printer is shipped with a letter- or A4-size paper tray that also accepts
transparencies and labels. Use additional trays for different types of media
to prevent frequent loading and unloading of a single tray. For printing
transparencieshigh-volume transparency and label printing, the optional
transparency tray is recommended.
Lower Paper Tray Assembly
With a 625-sheet capacity, the Lower Paper Tray Assembly is recommended
for high-volume printing needs and if you commonly print on several types
of media. For example, ofÞce paper can be loaded in the lower tray and
transparencies, letterhead, or label media in the upper tray. Using the
optional Lower Paper Tray Assembly, you can conÞgure the printer for
dual-tray printing.
Description
Order number
High-capacity transparency tray
(175-sheet capacity transparencies;
100-sheet capacity labels)
Letter-size
A4-size
436-0301-0001
436-0302-0102
Paper/transparency tray
(200-sheet capacity paper;
50-sheet capacity transparencies, labels)
Letter-size
A4-size
436-0293-0102
436-0292-0102
Lower Paper Tray Assembly (625-sheet capacity)
With letter-size paper tray
Z340LTA
With A4-size paper tray
Z340LTA: Option 01
436-0288-00
436-0289-00
Replacement letter-size tray
Replacement A4-size tray
10-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplies, Accessories, and Expanding Your Printing System 10
Memory upgrade
The Phaser 360 printer is shipped with 24 Mbytes of memory. It can be
upgraded to 48 Mbytes. Additional memory allows for faster processing,
faster ofßoading of print jobs from your computer to the printer, and more
storage for downloadable fonts.
Tektronix external hard disk
Description
Order number
External SCSI 2.1-Gbyte hard disk, bracket, and cable
ZDISK
You can connect an external hard disk to the printer for additional font
storage, collation, and increased memory for other printer functions. The
Tektronix SCSI hard disk mounts conveniently on the back of the printer.
For more information, refer to the following:
■
■
■
ÒConnecting an external hard disk (optional)Ó on page 2-17
ÒUsing the Quick Collate optionÓ on page 5-9
ÒDownloading fontsÓ on page 5-13
User Manual
10-5
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Supplies, Accessories, and Expanding Your Printing System
Additional software (UNIX and VMS)PhaserPrint™ for UNIX
software
Description
Order number
4690F20
PhaserPrint (for UNIX environments)
PhaserSym (for VMS environments)
4690F41
PhaserPrint™ for UNIX software
For printing in UNIX environments, Tektronix offers PhaserPrintª for
UNIX software. PhaserPrint software provides fast raster Þle and screen
copy printing to Tektronix color printers. PhaserPrint software also provides
a graphical user interface for push-button control of Tektronix
printer features. PhaserPrint software works with the workstationÕs native
spooling system to print PostScript Þles and raster Þles in the Sun Raster
Format (SRF), xwd, SGI RGB, and other formats.
Your printerÕs CD-ROM contains a demonstration copy of the PhaserPrint
for UNIX software and an on-line instruction guide in the unix/unixdemo
directory. Refer to ÒPrinting from a UNIX workstationÓ on page 4-41 for
more information.
PhaserSym™ software
For printing in VMS environments, Tektronix offers PhaserSymª software.
PhaserSym software is a VMS print symbiont for DEC OpenVMS VAX and
DEC OpenVMS AXP machines. PhaserSym software facilitates
communication between VMS hosts and Tektronix Phaser printers.
PhaserSym software requires that the Phaser printer include Ethernet
support.
10-6
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplies, Accessories, and Expanding Your Printing System 10
Interface cables and adapters
The following cables and adapters are available through Tektronix or your
dealer. Contact your dealer for other cables and adapters.
Description
Connectors and cable length
Order number
Parallel cable
36-pin high-density plug to 25-pin DSUB plug;
3 meters (9.84 feet)
012-1468-00
Connects the printer’s parallel port to
a PC or workstation parallel port.
Parallel/Centronics adapter
parallel adapter: converts 36-pin low-density 1284-B
plug to 36-pin high-density 1284-C plug
013-0299-00
012-1432-00
Adapts your system’s existing
low-density, Centronics parallel cable
connector to the printer’s high-density
parallel connector.
SCSI-2 HD to SCSI-1 LD cable
50-pin high-density plug to 50-pin low-density plug;
2.0 meters (6.56 feet)
Connects the printer’s SCSI port to a
hard disk drive.
SCSI-1 LD to Macintosh SCSI cable
50-pin low-density plug to Macintosh SCSI 25-pin plug 012-1299-00
Combine with 013-0297-00 to connect
the printer’s SCSI port to a hard disk
drive with Macintosh SCSI 25-pin
plug.
SCSI-1 LD to SCSI-2 HD adapter
SCSI adapter: converts 50-pin low-density plug to
50-pin high-density plug
013-0297-00
Use with either 012-1465-00 or
012-1299-00 to convert a low-density
SCSI connection to a high-density
SCSI connection.
User Manual
10-7
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Supplies, Accessories, and Expanding Your Printing System
10-8
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
11
Regulatory Information
and Specifications
Declaration of conformity
Tektronix, Inc.
Color Printing and Imaging Division
P.O. Box 1000
Wilsonville, Oregon 97070-1000 U.S.A.
declares, under our sole responsibility, that the product
Phaser 360 printer
to which this declaration relates, is in conformity with the following
standard(s) or other normative document(s):
The provisions of the Low Voltage Directive 73/23/EEC:
EN60950
Safety of Information Technology Equipment including Electrical Business Equipment
The provisions of the Electromagnetic Compatibility Directive 89/336/EEC:
EN55022:1992
Limits and Methods of measurement of radio interference characteristics of Information
Technology Equipment.
EN61000-3-2:1995
EN61000-3-3:1994
EN50082-1:1992
“Part 3: Limits – Section 2: Limits for harmonic current emissions (equipment input
current ≤ 16A per phase).”
“Part 3: Limits – Section 3: Limitation of voltage fluctuations and flicker in low-voltage
supply systems for equipment with rated current ≤ 16A.”
“Electromagnetic compatibility Generic immunity standard Part 1: Residential, commercial
and light industry.”
User Manual
11-1
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Regulatory Information and Specifications
Environmental phenomena
Test specification
Basic standard
Radio-Frequency Electromagnetic Field
80 – 1000 MHz
3 V/m (modulated)
EN61000-4-3:1995
Electrostatic Discharge
8 kV (charge Voltage)
IEC801-2:1984
Fast Transients common mode on Signal
lines
0.5 kV (peak)
5/50 Tr/Th ns
5 kHz Rep. Frequency
IEC801-4:1988
Capacitive Clamp
AC main ports
1 kV
This product, if used properly in accordance with the userÕs instructions, is
not dangerous for the consumer or the environment.
Canadian EMC (Electromagnetic Compatibility)
regulatory standards
■
This digital apparatus does not exceed the Class B for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
■
Le prŽsent appareil numŽrique nÕŽmet pas de bruits
radioŽlectriques dŽpassant les limits applicables aux appareils
numŽriques de la classe B prescrites dans le R•glement sur le
brouillage radioŽlectrique ŽdictŽ par le ministere des
Communications du Canada.
11-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Information and Specifications 11
FCC Class B warning (for 115 VAC equipment)
The equipment described in this manual generates and uses radio frequency
energy. If it is not installed and used properly in strict accordance with
TektronixÕ instructions, it may cause interference with radio and television
reception.
This equipment has been tested and found to comply with the limits for a
Class B veriÞed digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a commercial environment. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user
will be required to correct the interference at his own expense.
Warning Changes or modifications not expressly approved by Tektronix
can affect emission compliance and could void the user’s
authority to operate this product. To ensure emission
compliance, use shielded interface cables.
Material Safety Data Sheets
Proper management of environmental resources protects the well-being of
our employees, customers, shareholders, and the communities we are a part
of worldwide.
Tektronix establishes and maintains sound environmental management
practices to accomplish this goal and to assure compliance with the laws,
regulations, and orders of the responsible governmental authorities
wherever Tektronix and its subsidiaries operate.
Tektronix, Inc., is complying with government regulations by providing
Material Safety Data Sheets for our products.
Color Printing and Imaging Division
Tektronix, Inc.
User Manual
11-3
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Regulatory Information and Specifications
MSDS for ColorStix ink sticks
Section 1 – Product identification
Trade name and Tektronix part number:
®
ColorStix Solid Ink — Black
016-1307-00
®
ColorStix Solid Ink — Cyan
016-1308-01
016-1309-01
016-1310-01
®
ColorStix Solid Ink — Magenta
®
ColorStix Solid Ink — Yellow
®
Product use: For use in Tektonix Phaser 340/350/360 color printers.
Section 2 – Information on ingredients
Ingredients:
Fatty amide waxes; rosin ester; phthalate ester; black, cyan, magenta, or yellow dye
The specific identity of ingredients, and their percentage composition, are withheld as a trade secret.
Section 3 – Hazards identification
Potential Health Effects:
Eyes: Contact unlikely. If any particles get into the eye, flush thoroughly with water.
Skin: Not an irritant, based on test results.
Inhalation: Not an expected route of exposure.
Ingestion: Not an expected route of exposure. See section 11.
Section 4 – First aid measures
None indicated. This product is a waxy solid and should not cause health hazards when used as intended.
Section 5 – Fire fighting measures
Flammable Properties:
Flash point: Above 200° C.
Fire & explosion hazards: These inks will burn. No unusual hazards are expected.
Section 6 – Accidental release measures
Spill or Leak: Not applicable.
Section 7 – Handling and storage
Handling: None.
Storage: Avoid high temperatures.
Section 8 – Exposure control – personal protection
No special protection indicated when used as intended.
TLV/PEL: None established.
Section 9 – Physical and chemical properties
Appearance: Waxy solid. Black, blue, red, or yellow in color.
Odor: None.
Solubility: Not water soluble.
11-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Information and Specifications 11
Section 10 – Stability and reactivity
Stability: Stable.
Incompatibility with Other Materials: None.
Hazardous Polymerization: Will not occur.
Section 11 – Toxicological information
Toxicity: Not toxic, as determined by standard laboratory tests for acute oral toxicity.
Skin Irritation: Not an irritant, based on standard tests.
Skin Sensitization: Not a sensitizer, based on standard tests.
Carcinogenicity: Components or product not listed by IARC, NTP, or OSHA.
Section 12 – Ecological information
No known impact.
Section 13 – Disposal considerations
These products are not a hazardous waste as specified in 40CFR 261. Dispose in accordance with all federal, state,
and local regulations.
Section 14 – Transport information
D.O.T.: Not regulated.
NMFC: 101720 Sub. 3 - Ink, Printing, N.O.I., Class 55.
Section 15 – Regulatory information
TSCA: All components of these inks are listed in the Toxic Substances Control Act inventory as verified by our
suppliers.
SARA: Not reportable.
RCRA: TCLP below hazardous waste levels set by EPA.
CERCLA: No reportable quantity for this material.
California Prop. 65: Not listed.
Section 16 – Other information
Original preparation date: March 10, 1994 RC
Corrected MS & WV address 4/20/95 RC
Revised product use 11/5/96 JMP
Corrected Flash Point 4/28/97 JMP
Revised product use 12/5/97 JMP
Tektronix, Incorporated
P.O. Box 500
Chemical Documentation
Mail Stop 46-840
Beaverton, Oregon 97077
Printer information: 1-800-835-6100
MSDS information: (503) 627-7255
User Manual
11-5
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Regulatory Information and Specifications
MSDS for silicone oil (drum fluid)
Section 1 – Product identification
Trade name and Tektronix part number:
Silicone fluid (found in maintenance tray)
006-7912-00
®
Product use: For use in Tektronix Phaser 340/350/360 color printers.
Section 2 – Information on ingredients
Ingredients:
Polydimethylsiloxane
Hazardous Ingredients:
None. This is not a hazardous material as defined by the OSHA Hazard Communication Standard.
Section 3 – Hazards identification
Potential Health Effects:
Eyes: Direct contact may cause temporary discomfort with mild redness and dryness similar to windburn.
Skin: A single prolonged exposure (24 to 48 hours) causes no known adverse effect.
Inhalation: Not an irritant to respiratory passages.
Ingestion: Swallowing large amounts could cause discomfort.
Carcinogenicity: This material is not listed as cancer-causing by IARC, NTP, or OSHA.
Section 4 – First aid measures
Eyes: Flush immediately with water.
Skin: Wipe off and wash with soap and water.
Inhalation: Not a likely route of exposure. No first aid should be needed.
Oral: No first aid should be needed.
Section 5 – Fire fighting measures
Flammable Properties: Flammable limits not determined.
Flash point: 570° F, minimum, open cup.
Fire & explosion hazards: No unusual hazards known.
Section 6 – Accidental release measures
Spill or Leak: Wipe with absorbent material and dispose in accordance with federal, state, and local regulations.
Section 7 – Handling and storage
Handling: No special requirements.
Storage: No special requirements.
Section 8 – Exposure control – personal protection
Exposure Guidelines: None established.
Engineering Controls: None needed when used as intended in Tektronix printers.
Eye Protection: None needed.
Skin Protection: None should be needed.
Respiratory Protection: None needed.
11-6
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Information and Specifications 11
Section 9 – Physical and chemical properties
Appearance: Colorless liquid.
Odor: Slight.
Solubility: Not water soluble.
Section 10 – Stability and reactivity
Stability: Stable.
Incompatibility with Other Materials: Oxidizing compounds can cause a reaction.
Hazardous Polymerization: Will not occur.
Hazardous Decomposition Products: Traces of formaldehyde may form if heated in air above 300° F (149° C).
(Normal operating temperature in this printer is 50° to 60° C.)
Section 11 – Toxicological information
Acute oral LD : Greater than 50 ml/kg (Guinea pig).
50
Eye Irritation: Very mild irritant, normal after 24 to 48 hours.
Skin: Not a skin irritant.
Mutagenicity: Negative in Ames test, with and without metabolic activation.
Section 12 – Ecological information
No known impact.
Section 13 – Disposal considerations
Observe all federal, state, and local regulations. See section 15.
Section 14 – Transport information
D.O.T.: Not regulated.
Section 15 – Regulatory information
EPCRA section 313 Reportable Ingredients: None.
California Prop. 65: Not listed.
Canadian WHMIS: Not considered a hazardous chemical.
TSCA: This product is listed in the Toxic Substances Control Act inventory as verified by our suppliers.
OSHA: Not considered a hazardous material as defined by 29CFR1910.1200 Hazard Communication.
Section 16 – Other information
Original preparation date: October 21, 1994 RC
Corrected MS, etc. 4/20/95 RC
Revised product use, etc. 2/7/97 JMP
Revised product use 12/5/97 JMP
Tektronix, Incorporated
P.O. Box 500
Chemical Documentation
Mail Stop 46-840
Beaverton, Oregon 97077
Printer information: 1-800-835-6100
MSDS information: (503) 627-7255
User Manual
11-7
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Regulatory Information and Specifications
Specifications
Printer tilt
Place the printer on a level surface with no more than 3 degree tilt in any
direction, equivalent to raising one corner of the printer approximately 2 cm
(0.75 in.).
Caution
Tilting the printer more than 3 degrees causes drum fluid to
leak from the maintenance tray resulting in damage to your
printer not covered by the printer’s warranty.
Temperature
Operating:
Nonoperating:
Storage:
10¡ C to 32¡ C (50¡ F to 95¡ F)
Ð30¡ C to +60¡ C (Ð22¡ F to 140¡ F)
Ð30¡ C to +60¡ C (Ð22¡ F to 140¡ F)
Humidity
Operating:
Nonoperating:
10% to 80% Relative Humidity, noncondensing
10% to 95% Relative Humidity, noncondensing
Altitude
Operating:
Nonoperating:
0 to 2,400 meters (0 to 8,000 feet)
0 to 15,000 meters (0 to 50,000 feet)
Primary voltage ranges
87 Ð 128 VAC, 115 VAC nominal
174 Ð 250 VAC, 220 VAC nominal
Frequency range
48 to 66 Hz
AC input ratings
115 VAC, 10 Amps
220 VAC, 5 Amps
11-8
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Information and Specifications 11
Print quality and speed*
Fast Color mode color print on paper: 6 pages per minute
Fast Color mode color print on transparency: 5.5 pages per minute
Standard mode color print on paper: 4 pages per minute
Standard mode color print on transparency: 2 pages per minute
Enhanced mode 800 x 450 dpi color print on paper: 2 pages per minute
Enhanced mode 600 x 300 dpi color print on transparency: 2 pages per
minute
* Left and right margins set to 7.4 mm (0.3 in.) or larger.
Power consumption
Operating power consumption: 140 to 480 Watts
Meets Energy Star power conservation requirements
with the Energy Star timeout set to one hour.
Printer Dimensions
Height: 33 cm (13 in.)
Depth: 50.2 cm (19.75 in.)
Width: 40 cm (15.75 in.)
Weight: 32 kg (70 lb.)
Printer Clearances
Top:
45.7 cm (18 in.)
Sides: 10.2 cm (4 in.)
Front:
no restrictions
Rear: 10.2 cm (4 in.)
Bottom: no restrictions
Lower Paper Tray Assembly Dimensions
Height: 13.0 cm (5.13 in.)
Depth: 50.8 cm (20 in.)
Weight: 7 kg (15.5 lb.)
Width: 40 cm (15.75 in.)
User Manual
11-9
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Regulatory Information and Specifications
Safety and emissions
■
Listed: UL 1950 Information Technology Equipment.
■
Certified: CSA Standard C22.2 No. 950Ð95, 3d ed., Safety of
Information Technology Equipment, Including Electrical Business
Equipment.
■
■
Certified: EN60950.
Class B compliant computing device pursuant to subpart J of Part
15 of FCC rules.
■
Conforms to EC EN55022:1992; EN61000-3-2:1995;
EN61000-3-3:1994; EN50082-1:1992.
11-10
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
instructions printout 7-34
lower pick rollers 7-43
media-pick roller 7-34
overview 7-14
paper pick or separator pad 7-38
precaution with paper-feed rollers 7-23
precautions using alcohol 7-19
printdrum 7-30
A
adapters, ordering 10-7
adding ink 7-6
adjusting low-resolution images 5-11
adjusting printed colors 5-2
Adobe Type 1 and Type 3 fonts 5-13
alcohol
printhead 8-12
printing a test print 8-13
supplies, illustrated 7-18
table of problems and solutions 7-15
using alcohol-soaked swab 7-19
using isopropyl alcohol 7-19
using presoaked alcohol cloth wipes 7-19
cleaning kit contents 7-18
Cleaning Page
purity of 7-19
using for cleaning 7-19
Apple LaserWriter 8 driver, using 4-39
B
blue color, adjusting for 5-3
changing the media tray source 7-16
function of 7-16
output of, during warm up 2-23
cleaning tray
C
cables, ordering 10-7
Cancel button, location 6-3
Check Print
illustration 7-36
inserting into media tray 7-37
when to use 7-34
CMYK color sampler 6-7
collating
segmenting of large print jobs 5-9
with Quick Collate option 5-9
color
previewing print jobs 5-10
CIE colors 5-3
Clean button, location 6-3
cleaning
adjusting or correcting 5-2
how to use 5-7
problems with 8-31
Cleaning Page 7-16
for light stripes or missing colors 8-12
for Lower Paper Tray Assembly jams 7-43
ink smears
from internal paper path 7-20
from paper-exit path 7-28
from paper-feed problems 7-22
preventing 8-17
User Manual
Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
color corrections 5-2
Automatic 5-3
D
desktop printers, QuickDraw GX
drivers
Commercial Press 5-4
descriptions of 5-3
Euroscale Press 5-4
from an application 5-8
Monochrome 5-5
None 5-5
Simulate Display 5-4
SWOP Press 5-4
installing
Macintosh 3-17
Windows 3-2
using
Use Printer Setting 5-5
Vivid Color (blue) 5-3
color sampler charts
CMYK 5-6
drum ßuid
HSB 5-6
PANTONE Color 5-6
RGB 5-6
cleaning 7-28
precaution 7-9
dual-tray printing 4-8
ColorStix ink sticks, see ink
Commercial Press color correction
description of 5-4
E
communication ports 2-18, 4-25
ConÞguration Page
email update notices from Tektronix 9-1
email, receiving, when the printer needs
attention 1-3
description of 6-6
printing 2-25
connecting the printer 2-18
to a Macintosh 2-21
to a network 2-19
emissions 11-10
Energy Star
power requirements 11-9
resetting the default value 6-8
Enhanced print-quality mode (800 x 450
dpi) 4-4
error messages and codes, front panel 8-2
errors, PostScript 8-26
Euroscale Press color correction
description of 5-4
to a PC 2-20
to a UNIX workstation 2-20
controlling access to the front panel menu 6-4
correcting printed colors 5-2
customer support
customer support centers 9-2
getting information by fax 9-3
on-line help 9-1
Exit button 6-3
Index-2
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
external hard disk
connecting 2-17
description ot 1-9
for collating 2-17
ordering 10-5
location 1-4
overview 6-1
status messages 6-2
types of messages 2-22
front panel menu
accessing 2-22
enabling and disabling 6-4
F
Fast Color print-quality mode 4-4
fax, getting information by 9-3
features
G
selecting from the front panel 4-3
selecting in a Macintosh driver 4-36
selecting in a Windows driver 4-20
font list, printing
H
from a Macintosh 5-15
from a PC 5-15
HAL, fax reference library 9-3
Font Sampler, Macintosh utility Þle 5-15
fonts
printing 6-7
Adobe Type 1 and Type 3 5-13
downloading 5-13
PostScript fonts 5-12
printer fonts 5-12
I
image area 4-7
margins 4-7
resident typefaces (PCL5) 5-12
resident typefaces (PostScript) 5-12
TrueType 5-13
image resolution, see print quality
Image Smoothing 5-11
indicators
error 2-23
power 2-23
Info button 6-3
ink
using with Windows 5-14
FONTS.PS, PC utility Þle 5-15
front cover, location 1-4
front panel
button functions 6-3
Check Print 5-10
display lines 6-2
error messages and codes 8-2
indicator lights 6-1
language change 2-24
adding 7-6
adding at setup 2-10
description of ColorStix ink sticks 1-7
handling waste ink 7-8
loading precautions 7-7
minimizing consumption of 2-26
ordering 10-2
tips for handling 7-7
User Manual
Index-3
Download from Www.Somanuals.com. All Manuals Search And Download.
ink smears
cleaning internal paper path 7-20
Lower Paper Tray Assembly
attaching to printer 2-4
capacity 2-15
cleaning paper-exit path 7-28
cleaning paper-feed rollers 7-22
preventing 8-17
changing the default media tray 4-10
cleaning the paper-pick rollers 7-43
Þll line 2-15
installing
software 3-1
installing 2-4
loading 2-15
media used with 4-8
misfeeds 7-43
order number 10-4
paper jams 7-43
use with upper tray 4-8
LPT port problems 8-23
L
labels
acceptable tray for 4-6
printing 4-12
M
type to use 4-12
language modes, checking 8-25
languages
Macintosh printer driver
selecting printer in Chooser 3-18
Macintosh utility Þles, Font Sampler 5-15
maintenance
default 5-12
printer 5-12
cleaning the printer 7-14
printerÕs self-cleaning 7-16
maintenance tray
LaserWriter 8.x driver, using 3-19
leaving the printer on 2-26
letterhead
capacity 7-11
loading 4-11
description of 1-7
running a test sheet 4-11
using the manual feed 4-17
light or missing stripes
cleaning for 8-12
precautions 7-4
relatching to clear media jams 7-34
replacing 7-11
identifying 8-12
manual feed 4-16
loading ink, see ink
loading labels 4-12
loading letterhead 4-11
loading paper 2-11
loading transparencies 4-13
LocalTalk connection 2-19
locking the transit restraint 7-4
location 1-4
paper jams 4-18
paper weight acceptable 4-6
printing letterhead 4-17
printing transparencies 4-17
when to use 4-16
Index-4
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
margins
image area 4-7
media 4-7
media 4-6
N
network interfaces, order numbers 10-3
image area 4-7
margins 4-7
sizes and weights acceptable 4-6
types acceptable 4-6
media jams
cleaning lower paper-pick rollers 7-43
cleaning the media-pick roller 7-34
clearing 8-17
locating 8-16
output after clearing 8-15
preventing 8-15
O
oil (printer drum ßuid), cleaning 7-28
on-line customer support 9-1
order number
cables and adapters 10-7
cleaning kit 10-2
media trays 10-4
media trays
changing the default setting 4-10
loading 2-11
Lower Paper Tray Assembly 10-4
lower tray jams, cleaning for 7-43
order numbers 10-4
types 4-8
upper tray jams, cleaning 7-34
Menubutton
displaying printer menus 2-22
label changes 6-3
menu map, front panel 6-6
menus, printer front panel 2-22
Microsoft Windows NT PostScript printer
driver, updating 4-31
P
packing material, removing 2-3
PANTONE Colors, printing 8-32
paper 4-6
acceptable types 4-6
cleaning pick rollers 7-34
duplex warning 4-6
image area 4-7
letterhead, loading 4-11
loading 2-11
manual feed 4-6
margins 4-7
recycling 4-6
types, size, and weight 4-6
misfeeds
cleaning for 7-34
Lower Paper Tray Assembly 7-43
see also media jams
Monochrome color correction 5-5
moving the printer 7-2
locking the transit restraint 7-4
precautions 7-4
removing the maintenance tray 7-3
MS-DOS, printing from 4-34
User Manual
Index-5
Download from Www.Somanuals.com. All Manuals Search And Download.
paper jams, see media jams
paper pick roller cleaning, lower 7-34
paper pick roller cleaning, upper 7-43
paper tray
PostScript
errors, general 8-26
fonts 5-12
PostScript Header
printing Þles 5-12
timeout 8-30
acceptable media for 4-8
capacity 4-8
loading 2-11
order numbers 10-4
printing transparencies 4-14
using for transparencies 4-8
parallel cable, ordering 10-7
parallel port, connecting to 2-20
PC utility Þles
FONTS.PS 5-15
TIMEOUTS.PS 8-30
PC/NFS
PostScript Header
power indicator 2-23
PowerPoint users, image quality solution 8-6
previewing print jobs 5-10
print features
overview 4-2
selecting 4-2
print quality
Network Option 4-28
selecting network settings 8-23
PC/Windows software 3-2
PCL5, printing 5-12
Enhanced mode 4-4
Fast Color mode 4-4
selecting 4-4
Phaser 380 (LaserWriter 7.1.2-based) printer
driver, see Macintosh printer driver
Phaser 560 driver, using 4-38
Phaser 560 GX driver, using 4-40
PhaserLink software 1-3
PhaserPrint for UNIX software
description 4-41
Standard mode 4-4
print resolution, see print quality
print speed
improving 5-16
Standard mode 4-4
printdrum, cleaning 7-30
printer drivers
order number 10-6
PhaserPrint, Photoshop plug-in 3-16
PhaserShare network cards
conÞguring 2-19
order numbers 10-3
PhaserSym software 10-6
description 4-41
order number 10-6
pick roller cleaning tray, see cleaning tray
ports, see communication ports
installing
Macintosh 3-17
Windows 3-2
using
Macintosh 4-35
Windows 4-19
printer fonts 5-12
Index-6
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
printer languages 5-12
default 5-12
printer management software 1-3
printer menus 2-22
printer parts and components 2-2
PRINTER.INF, updating Windows NT
driver 4-31
R
rear panel ports 2-18
registering your printer 9-1
registration, on-line 9-1
replacing the maintenance tray 7-11
resident typefaces
PCL5 5-12
PostScript 5-12
printing
a font list 5-15
a test page 8-13
a truer blue 5-3
printing a list of 5-15
color sampler charts 5-6
from a Macintosh 4-35
from a network 8-33
from a PC 4-19
from applications 4-44
Help Pages 6-7
in gray scale 5-5
labels 4-12
letterhead 4-11
transparencies 4-13
S
safety and emissions 11-10
selecting
a front panel language 2-24
pages sizes in Windows applications 5-19
print features 4-2
print-quality modes 4-4
setting page margins 4-7
setting the Check Print timeout 5-11
shipping the printer, see moving the printer
Simulate Display color correction 5-4
software, installing 3-1
speciÞcations 11-8
problems and solutions
image quality 8-6
Standard print-quality mode 4-4
standby modes
media feeding and jamming 8-5
operational hints 2-26
printing and installation 8-8
Energy Star 6-8
leaving the printer on 2-26
normal 6-8
Startup Page 6-6
Q
disabling 6-6
Quick Collate 5-9
during warm up 2-23
nonfatal error at power-up 8-10
printing 6-6
quick reference 4-36
selecting features, Macintosh 4-36
selecting features, Windows 4-20
QuickDraw GX, Tektronix printer driver 3-21
stripes in prints, cleaning 8-12
supplies, ordering 10-2
SWOP Press color correction
description of 5-4
User Manual
Index-7
Download from Www.Somanuals.com. All Manuals Search And Download.
loading 2-11
printing from 4-13
T
technical support, see customer support
Tektronix Bulletin Board Service (BBS) 3-23
Tektronix Color Printer web site 9-1
test page, printing 8-13
timeouts
troubleshooting
front panel error messages 8-2
TrueType fonts 5-13
turning on the printer 2-21
Windows 3.1 8-28
Windows 3.1 driver 4-29
Windows printer driver 4-26
TIMEOUTS.PS, PC utility Þle 8-30
tips
U
for handling ink 7-7
for optimum printing 2-26
for printing transparencies 4-15
for working with color 5-7
top cover, location 1-4
transit restraint
UNIX workstations 4-42
installing printer software 3-23
software for 10-6
used ink, disposal of 7-8
using color 5-7
location 1-4
using color corrections 5-2
using your web browser for printer
management 1-3
locking before moving printer 7-4
unlocking for set up 2-7
Transmission Retry
utility Þles 3-23
Windows 4-29
Windows 3.1/Tek driver 4-26
Windows 95/Adobe & Microsoft
driver 4-22
V
Vivid Color color correction 5-3
VMS software, ordering 10-6
VMS workstations, software for 4-43
transparencies
acceptable types 4-13
loading 2-11
manual feed printing 4-17
order number 10-2
precautions 4-15
printing from the paper tray 4-14
printing from the transparency tray 4-13
printing instructions 4-13
size 4-6
tips 4-15
tray types 10-4
using Tektronix 4-5
transparency tray
capacity 4-8
Index-8
Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
W
warming up the printer 2-23
time necessary for 2-23
waste liner
description of 1-7
emptying 7-8
web site, Tektronix 9-1
weight, paper 4-6
Windows 3.1 driver
Features tab 4-29
improving print speed 5-17
Job Control tab 4-30
Paper tab 4-29
PostScript tab 4-30
problems with setting page sizes 5-19
timeout PostScript driver 4-29
timeouts 8-28
using 4-29
Windows 95 driver
Details tab 4-22
Device Options tab 4-23
Graphics tab 4-23
Paper tab 4-22
PostScript Header 4-24
PostScript tab 4-24
timeout 8-28
using Adobe and Microsoft drivers 4-22
using PostScript driver 4-29
Windows printer driver
conÞguring 4-25
timeouts 4-26
workstation software
PhaserPrint for UNIX, ordering 10-6
PhaserSym for VMS, ordering 10-6
World Wide Web, Tektronix Color Printer
web site 9-1
User Manual
Index-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-10 Phaser 360 Color Printer
Download from Www.Somanuals.com. All Manuals Search And Download.
|