To take maximum advantage of all the features of your satellite receiver,
please read this user manual very carefully.
ASR 0 8 T SATELLITE RECEIVER
The package contains the following items :
• Satellite receiver
• Remote control unit
• SCART cable
• Two batteries, type R03 (AAA)
• User manual
• List of pre-programmed channels
In the unlikely event of one of these items being missing, please contact your dealer.
REMO TE CO N TRO L
Insta lling the b a tteries
Remove the battery compartment cover,
located at the back of the remote control unit.
Insert the two 1.5-V (AAA) batteries.
Be sure to observe polarity.
For your inform a tion
If the remote control seems to have stopped operating correctly,
replace the batteries.
Wa rning
- Do not expose the batteries to excessive heat (sun, fire, etc.).
- Do not recharge ordinary batteries.
- Do not let children play with batteries; they may try to swallow them.
- Consult a doctor immediately if a battery has been swallowed.
Protect the environm ent!
• Do not dispose of used batteries via the rubbish bin.
• Place them in the containers provided for this purpose.
• Find out where such containers are located in your area.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Page
CO N TEN TS
REMOTE CONTROL UNIT.................................................................................... 5
FRONT PANEL KEYPAD ....................................................................................... 6
REAR PANEL CONNECTIONS.............................................................................. 6
INSTALLATION OF SATELLITE RECEIVER ............................................................ 7-8
EVERYDAY USE................................................................................................... 9
RECORDING SATELLITE PROGRAMMES ..............................................................10
PROGRAMMING A NEW CHANNEL.............................................................11-12
SPECIAL FEATURES........................................................................................13-14
CONVENIENCE FEATURES.................................................................................15
TROUBLESHOOTING..........................................................................................16
SPECIFICATIONS...........................................................................................16-17
4
Download from Www.Somanuals.com. All Manuals Search And Download.
REMO TE CO N TRO L UN IT
STANDBY key (Switch set on using the
CHį/ CHĬ keys, or 0 to 9)
PL
PL
Parental lock.
EXIT
COPY
HFB
0
9
Numeric keypad :
- Channel selection
- Frequency entry
1
4
2
5
3
6
- Toturn on the receiver.
Channel scrolling (zapping) and to turn on the
receiver.
CH
7
8
0
9
COPY
VL
DEC
To interchange two programme numbers.
Video level selection.
VL
TUNE
TUNE
DEC
Decoder mode selection.
22 kHz signal On/ Off.
22 KHZ
AUDIO
EXIT
CH
Audio frequency display.
VIDEO
AUDIO
C/KU
V/H
A-M
LNB
To exit programming mode and return to the
programme display.
22 KHZ
STORE
C/KU
A-M
STORE
Band C or Ku selection.
Audio mode selection.
HFB
This key has no function.
VIDEO
LNB
Video frequency display.
Selection of the LNB input and DiSEqC function.
Polarisation selection.
V/H
Frequency and volume adjustment.
STORE
STORE
Memory keys (to store in memory, press the two
keys together).
TUNE TUNE
Audio and Video frequency adjustment.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FRO N T PAN EL KEYPAD
ቤ On/ Standby button
ቢ Programme number display
Satellite receiver ASR08T
400 programs
Sound Wegener Panda
DiSEqC ToneBurst
CH
ባ Channel scrolling keys
REAR PAN EL CO N N ECTIO N S
ብ IF A input - socket to connect the LNB of
your satellite antenna (e.g. ASTRA)
ቪ AUDIO L/ R :
CINCH sockets to connect a
stereo system.
ቩ SCART socket to connect a
video cassette recorder (VCR)
WARNING!
Shock Hazard
Do not open
MADE IN
GERMANY
A
L
VCR
IF INPUT
B
R
TV
DECODER
ቦ IF B input -
socket to connect
a second LNB
ቨ SCART socket to
connect a decoder
ቫ Mains socket to connect the
set to the ac power supply.
(e.g. EUTELSAT II -
F1/ HOTBIRD)
ቧ SCART socket to
connect the television set
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IN STALLATIO N O F SATELLITE RECEIVER
A correctly installed satellite antenna is essential for the receiver to operate.
The satellite antenna coaxial cable must be long enough to reach the desired receiver
site.
Install the receiver near your television set, making sure to leave ventilation space of about
15 cm to the sides and above the receiver. Do not obstruct the ventilation slots of the
receiver.
You can install the receiver according to the following example :
Satellite antenna
TV
Ant.
SCART
cable
VCR
WARNING!
Shock Hazard
Do not open
MADE IN
GERMANY
A
L
VCR
IF INPUT
B
230 V-
50 Hz
26 W max.
R
TV
DECODER
Decoder
- Do n o t y e t co n n e ct the set to the mains.
- Plug F must be correctly installed on the coaxial cable of the LNB. Remove the cable
sheath, fold back the braid (ensure that the central strand of the cable does not touch the
braid, to avoid a short circuit), and manually turn the plug to tighten it on the coaxial
cable.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IN STALLATIO N O F SATELLITE RECEIVER
- Connect the LNB coaxial cable to Socket ብ IF INPUT A.
- You can, if applicable, connect a second LNB to IF INPUT B connector ቦ. Plug F must be
tightened by hand on the threading of the plug. Do not use any tools. Take care not to jam
the plug.
- You can now connect your equipment to the mains power supply. To do this, connect one of
the ends of the mains cable to connector ቫ on the receiver and the other end to a mains
socket.
Our description of the receiver assumes that the set has been installed according to
instructions!
1 . Co n n e ctio n to a Te le visio n Se t :
- Using a SCART cable (supplied), connect the Socket ቧ TV-SCART of your receiver to the
SCART socket of your Television Set. This connection provides optimum picture and sound
quality.
2 . Co n n e ctio n to a VCR :
- Using a SCART cable (not supplied), connect the Socket ቩ VCR-SCART of your receiver
to the SCART socket of your VCR.
The equipment is operated using a cascade connection.
The video recorder images will be transmitted to the TV through the TV SCART connector
ቧ if the video recorder supplies the control voltage when it is in read mode (12V on pin
8 of the VCR SCART connector ቩ).
3 . Co n n e ctio n to a d e co d e r
Using a SCART cable (not supplied), connect the Socket ቨ DECODER-SCART of your
receiver to the SCART socket of your decoder.
4 . Co n n e ctio n to a ste re o sy ste m :
Your satellite receiver can be connected to a stereo system using the CINCH connectors ቪ.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
EVERYDAY USE
O n / Sta n d b y
Using set keypad:
Press the On/ Standby key.
Using remote control:
Switch the receiver on by pressing one of the numeric keys (0 to 9),
remote control keypad.
or
on the
If the set is switched on using the
or
keys, the last programme number active
before switching off is called up, for example : " 13".
To switch the set off, press the Standby key.
The display shows : " -"
Pro g ra m m e Se le ctio n
Using set keypad:
Press the programme scrolling keys ̆̄
Using remote control:
a) Direct selection using numeric keys 0 to 9, or
b) Channel scrolling using the
or
.
a) Direct selection:
For the first ten programmes, press the corresponding key briefly.
For two- or three-digit programme numbers, the number must be entered in three
seconds.
For example, to select Programme 14:
- Briefly press the 1 key " -1" appears on the display.
- Press the 4 key within three seconds to display " -14".
Programme 14 is displayed on the screen.
Examples:
Enter 1
Enter 24
Enter 399
Display : -1
Display : -24
Display : 399
Programme 1
Programme 24
Programme 399
appears on screen
appears on screen
appears on screen
b) Channel scrolling using the
or
keys.
Press the
Press the
key to select the next programme.
key to select the further programme.
Vo lu m e Ad ju stm e n t
You can adjust the receiver volume using the VOL + (louder) and VOL - (softer) keys. The
last setting in use is stored in memory when the receiver is placed on Standby.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
RECO RDIN G SATELLITE PRO GRAMMES
If your receiver is connected to a VCR, you can record satellite programmes. Paragraph
2 : Connection to a VCR in the INSTALLATION OF SATELLITE RECEIVER chapter of the
present manual describes the procedure for connecting the VCR to the receiver.
Refer also to your VCR user manual.
On your satellite receiver, select the channel you wish to record, then, on the VCR, select
the programme number assigned to the satellite receiver (e.g. AV) and begin recording.
To avoid recording a different programme or nothing at all, do not change satellite
channel or switch off the receiver before recording is complete. You may, however,
change channels on your television set. This does not affect the recording.
If you wish to record a satellite programme during your absence, select the desired
channel on the receiver, and programme the recording start and stop times on your VCR.
You can leave the satellite receiver on without any problem.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO GRAMMIN G A N EW CHAN N EL
Your receiver is already programmed to receive the most important satellite signals. You
can, however, change the programming or add new channels at any time.
To store a new channel in memory, you need the following information (found in specialist
satellite TV magazines):
1. LNB selection
and ToneBurst signal
2. Polarisation
3. Video frequency
4. Audio mode
5. Audio frequency
First, select the programme number you wish to assign to the new channel, and then follow
the instructions.
1 . Se le ctio n o f LN B a n d o f To n e Bu rst sig n a l
You can connect 2 LNBs to your receiver (e.g. ASTRA and EUTELSAT II-F1 satellites).
Connect the LNBs respectively to connectors ብ and ቦ (IF INPUT A/ B). In addition, your
receiver can supply ToneBurst (DiSEqC) control signals. This function allows connecting 4
LNBs to your receiver. The LNBs must be connected in 2s to each of the IF INPUTs ብ and
ቦ, through a ToneBurst switch.
LNB
Press the
key to display the current mode, e.g. LnA1.
Press the key again to select the further mode.
DISPLAY LN B To n e Bu rst SIGN AL
DISPLAY LN B
To n e Bu rst SIGN AL
A Position
LnA1
LnA2
A1
A2
A Position
B Position
Lnb1
Lnb2
B1
B2
B Position
2 . Po la risa tio n Se le ctio n
To allow transmission of the greatest possible number of programmes, satellite broadcasts
come in two polarisations (vertical and horizontal).
V/H
Press the
key to display the current polarisation, e.g. : " V".
Press the key again to select the other polarisation.
Display : " V" = vertical (14 V)
Display : " H" = horizontal (18 V)
3 . Vid e o Fre q u e n cy Ad ju stm e n t
VIDEO
Press the
key to display the frequency in MHz, e.g. : «1406».
The value displayed on your receiver is not the frequency of the channel; it corresponds
to the difference between the channel frequency and the local oscillator frequency of your
LNB.
You can enter the desired frequency directly (4 digits) via the 0-9 numeric keypad, or
change the displayed value in steps of 1 MHz using the VOL + and VOL - keys.
Values outside the 700-2150 MHz band are not accepted.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO GRAMMIN G A N EW CHAN N EL
4 . Au d io m o d e se le ctio n
A-M
Press the
key to display the audio mode, e.g. : "Ton1".
Press several times to display all the available modes.
DISPLAY
"Ton 1"
"Ton 2"
"Ton 3"
"Ton 4"
"Ton 5"
MO DE
Stéréo
Mono
Mono
Mono
Mono
DE-EMPHASIS
Wegener Panda
Wegener Panda
50 µs
BAN DW IDTH
130 kHz
130 kHz
280 kHz
75 µs
280 kHz
J 17
280 kHz
5 . Au d io Fre q u e n cy Ad ju stm e n t
AUDIO
Press the
key to display the frequency in MHz, e.g. : "A702".
You can enter the desired frequency directly (three digits) using the 0-9 numeric keypad, or
change the displayed value in steps of 10 kHz using the VOL + and VOL - keys.
Values outside the 5.5-9.99 MHz band are not accepted.
AUDIO
Press the
key several times to display the eight pre-programmed audio modes in turn.
6.50 MHz
6.60 MHz
7.56 MHz
7.02 MHz
7.74 MHz
7.20 MHz
7.92 MHz
7.38 MHz
5 . Sto rin g in Me m o ry
Press the two STORE keys together to store all settings in memory. The programme is
displayed again.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
1 . Vid e o Le ve l
This feature lets you adjust the video level to compensate for differences in level that may
exist between the various satellites.
VL
Press the
key to display the current mode, e.g. : " HI ".
Press the key again to select the second mode.
" HI "
" LO "
= light image
= dark image
(16 MHz for ASTRA)
(25 MHz for EUTELSAT, INTELSAT, etc.)
2 . C/ Ku Ba n d
This feature is used to invert the video when receiving C-band satellite transmissions.
C/KU
Press the
key to select between Bands C and Ku.
CU 1 = Ku band (ASTRA, HOT BIRD, etc.)
CU 2 = C band
3 . Co n n e ctin g a De co d e r
ቨ
Decoder must be connected via SCART cable to Socket
Use the DEC key to select one of the five modes :
DECODER.
ቨ
Disp la y
Fu n ctio n
O u tp u t Sig n a l
Au d io So u rce
d -
Canal Satellite (mono)
Premiere
Composite video
clamped
External
Videocrypt
d 1
Canal Satellite (mono)
Premiere
Composite video
clamped
External
Videocrypt
d 2
d 3
d 4
CANAL + stereo
D2MAC
Composite video
clamped
Internal
External
Internal
Composite video
unclamped
Composite video
unclamped
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
4 . 2 2 k Hz Sw itch in g Sig n a l
This signal can be used to control either a switching box or, for example, the LNB (high
band/ low band).
22 KHZ
Press the
Press again to select the second mode.
"22 +" = 22 kHz switching signal in service
key briefly to display the current mode, e.g. : "22-".
"22--"= 22 kHz switching signal stopped.
EXIT
If you wish to exit Special Features, press the remote control
key briefly. The receiver
returns to programme display, without storing the modifications in memory.
All sp e cia l fe a tu re se ttin g s ca n b e sto re d in m e m o ry b y p re ssin g th e tw o
STO RE k e y s to g e th e r.
N o ta : For reception in High Band (TELECOM 2A and 2B), 22 kHz signal must be in
service.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CO N VEN IEN CE FEATURES
1 . Pa re n ta l Lo ck
Used to restrict use of the set, or access to certain programmes.
1. Locking certain programmes.
The programme can be selected, but the picture does not appear on screen.
The programming cannot be altered.
Locked programmes are indicated on the display by an L before the programme
number, e.g. : "L34"
2. Locking the entire set.
The satellite receiver cannot be used until the lock is deactivated.
The display shows : "L-".
PL
Press the
key (the display shows : "----")
then use the numeric keypad to enter one of the codes shown below.
PL
Then confirm the code by pressing
again.
PL
PL
key - enter code 6 7 2 5 -
key - programme locked.
key - receiver locked.
PL
PL
key - enter code 6 7 2 6 -
Repeat the procedure to deactivate the lock.
To prevent deactivation of the lock by an unauthorised person, keep the user manual in a
safe place.
2 . Da ta Tra n sfe r Fe a tu re
This feature is used to interchange the programme numbers of two channels.
Example : You wish to replace the channelofProgramme 1 with the channelofProgramme 3.
1.
Select Programme 1.
PL
2.
3.
4.
Press the
key briefly.
Select Programme 3.
Press the two STORE keys together.
The two programme numbers have now been interchanged.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TRO UBLESHO O TIN G
SYMPTO M
PO SSIBLE CAUSE
Display inoperative
- Mains lead incorrectly connected
- Power cut
Unable to switch
set on
- Short circuit in the coaxial cable connected to the LNB
No picture
- SCART cable incorrectly connected.
- Wrong LNB selection.
No sound
- Poor adjustment of frequency or audio mode
- SCART cable incorrectly connected
- Receiver volume too low
Poor picture quality
- Satellite antenna not installed according to instructions
- Damaged cable
- Satellite antenna too small
- Excessively poor weather conditions
Remote control inoperative
Display : FAIL
- Batteries incorrectly installed
- Batteries worn
- Remote control unit not pointing towards receiver
- Short circuit in LNB or cable connected to LNB
SP ECIFICATIO N S
- 399 PROGRAMME NUMBERS, ALL PROGRAMMABLE
- 2 IF INPUT
- PLL FREQUENCY ADJUSTMENT SYSTEM
- 2 AUDIO BANDWIDTH
- MULTI-PURPOSE LED DISPLAY
- 3 SCART SOCKETS FOR TELEVISION SET, VCR AND DECODER
- 14 V/ 18 V LNB POWER SUPPLY SWITCHING
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SP ECIFICATIO N S
RF PART
- INPUT FREQUENCY : 900-2150 MHz (IN STEPS OF 1 MHz)
- INPUT IMPEDANCE : 75 OHM
- INPUT LEVEL : -60 dBm -30 dBm
- INTERMEDIATE FREQUENCY : 479.5 MHz
- RESPONSE THRESHOLD : 6 dB
VIDEO PART
- DE-EMPHASIS : CCIR REC 405-1, 625 LINES
- FREQUENCY RESPONSE : 50 Hz - 4,0 Mhz (+1,5 dB / - 2 dB)
- OUTPUT LEVEL : 1 Vp-p TYPICAL
- PAL B/ B OUTPUT : 1,0 Vp-p (DE-EMPHASIS, UNFILTERED, UNCLAMPED)
- OUTPUT SOCKET : SCART
AUDIO PART
- FREQUENCY RANGE : 5,5 - 9,99 MHz (ADJUSTABLE IN STEPS OF 10 kHz)
- MODES : MONO & STEREO
- WEGENER PANDA
- AUDIO BANDWIDTH : 130 kHz and 280 kHz
- DE-EMPHASIS : 50 µS, 75 µS, J17
- FREQUENCY RESPONSE : 50 Hz - 15 kHz
- OUTPUT SOCKET : SCART + CINCH
FRO N T-PAN EL CO N TRO LS
- DISPLAY : STANDBY, 4 DIGITAL LEDS, IR SENSOR
- 3 TOUCHES : ON/ STANDBY, CHANNEL į/ Ĭ
REAR-PAN EL CO N N ECTO RS
- 2 LNB CONNECTORS : 2 TYPE F FEMALE
- 3 SCART SOCKETS (TV, VCR, and DECODER)
- MISCELLANEOUS : MAINS SOCKET
REMO TE CO N TRO L UN IT
- 32 KEYS WITH NUMERIC KEYPAD
- BATTERIES : 2 x 1.5 V LR 03 (INCLUDED)
MISCELLAN EO US
- POWER SUPPLY VOLTAGE : 210-250 V (ac)/ 50 Hz
- LNB POWER SUPPLY : (2x) 300 mA, 14 V/ 18 V SWITCHABLE
- DIMENSIONS : 370 (L) X 240 (D) X 70 (H) mm
- WEIGHT : 2.4 kg APPROX.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
|