TechniSat Satellite TV System DIGITY CI Operating Manual User Manual

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 1

DIGITY CI

features motor control and

software update via satellite

Operating Manual

With PCMCIA interface to accommodate a single

CA module. Provides reception of unencrypted

and encrypted (e.g. VIACCESS, IRDETO,

CRYPTOWORKS, SECA etc.) ASTRA and

EUTELSAT DVB programmes.

DiSEqC 1.2

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 3

6.12

6.12.1

6.12.2

Timer . . . . . . . . . . . . . . . . . . . . . . .21

Programming via EPG . . . . . . . . . . . . . . .21

Manual Programming . . . . . . . . . . . . . . . . .21

6.13

Video text . . . . . . . . . . . . . . . . . . .23

Changing basic programming . . . .24

Configuring programme list . . . . . . . . . . . .24

Calling up programme list . . . . . . . . . . . . .24

Adding programmes to programme list . . .24

Deleting programmes . . . . . . . . . . . . . . . . .25

Deleting from Favourites list . . . . . . . . . . .25

Deleting from Total list . . . . . . . . . . . . . . . .25

Sorting programmes . . . . . . . . . . . . . . . . .26

Blocking acces (parental control) . . . . . . . .26

Changin the PIN . . . . . . . . . . . . . . . . . . . .27

Unblocking access to individual

7.1

7.1.1

7.1.2

7.1.3

7.1.3.1

7.1.3.2

7.1.4

7.1.5

7.2

7.3

programmes . . . . . . . . . . . . . . . . . . . . . . . .27

Programme search . . . . . . . . . . . . . . . . . .28

Satellite . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Transponder . . . . . . . . . . . . . . . . . . . . . . . .29

Manual search . . . . . . . . . . . . . . . . . . . . . .30

Accepting programmes after search . . . . .30

Restoring basic programming/ delete all . .31

Activate default setting . . . . . . . . . . . . . . . .31

Delete all programmes . . . . . . . . . . . . . . . .32

Software update . . . . . . . . . . . . . . . . . . . . .32

System configuration . . . . . . . . . . . . . . . . .33

Encryption system . . . . . . . . . . . . . . . . . . .33

7.4

7.4.1

7.4.2

7.4.3

7.4.4

7.5

7.5.1

7.5.2

7.5.3

7.6

7.7

Operating a rotating installation .33

East and West limits . . . . . . . . . . . . . . . . .33

Geo-positioning . . . . . . . . . . . . . . . . . . . . .35

Setting satellite position . . . . . . . . . . . . . . .36

Selecting satellite position . . . . . . . . . . . . .36

Adjusting satellite antenna . . . . . . . . . . . . .37

Storing satellite position . . . . . . . . . . . . . . .38

Current satellite list . . . . . . . . . . . . . . . . . .38

Deleting satellite position . . . . . . . . . . . . . .39

Rotating to reference position . . . . . . . . . .39

8.1

8.2

8.3

8.3.1

8.3.2

8.3.3

8.4

8.5

8.6

Technical terms . . . . . . . . . . . . . .40

Technical data . . . . . . . . . . . . . . . .43

Trouble-shooting guide . . . . . . . . .45

Annexure . . . . . . . . . . . . . . . . . . . .47

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 4

2 Illustrations

Remote control

EXTERNAL

Sound on/off

Language selection

On/Standby

TV/Radio operation

MONO1/MONO2

Numeric keys

Menu on/off

Info

Programme +

Arrow key up

Volume -

Arrow key left

Programme list on/off

Volume +

EPG

Arrow key right

Programme -

Back

Arrow key down

Multi-function keys

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 5

Front panel

Programme selection

up/down

LED display

On/Standby

Rear panel

Inserting the CA module:

> Please follow the instructions of the card and module manufacturer.

> Insert the smartcard selected in the appropriate CA module.

> Now insert the module carefully in the slot, in the direction of the arrow

(arrow facing up.

Mains power

connection

LNB input

SCART socket TV

LNB

output

SCART socket

VCR

RS 232 interface

Audio output

left/right

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 6

3 Please read this first

Before commencing operation of the unit, please

check that you have received all the parts intended.

You should have the following:

1 Receiver, 1 mains power cable, 1 remote control

unit,

1 operating manual, 1 guarantee card, 2 batteries

(1,5V microcells).

Insert the batteries supplied in the battery

compartment of the remote control unit, ensuring

correct polarity as indicated.

Before connecting the receiver, please read the

security notes in Chapter 3.

Chapters 4 and 5 describe connecting the receiver,

and how to adapt the settings correctly for your

external unit (dish antenna, LNB, etc.) as well as for

the television set, VCR, etc.

Chapter 6 describes all the functions necessary for

day-to-day operation, e.g. programme selection or

volume adjustment.

In Chapter 7 you will find information on how to

install new programmes or how to change the order of

programmes in the list.

Chapter 8 describes the settings to be made when

using a rotating antenna installation.

The key technical terms used in this operating manual

are explained in Chapterl 9.

Technical data can be found in Chapter 10.

Assistance in finding and correcting problems can be

found in Chapter 11.

Important operating information

The implementation of an "On Screen Display" (information

displayed on the TV screen, see example) simplifies the

operation of the receiver, and reduces the number of keys

required on the remote control. All functions are displayed on

the screen, and can be set or changed with a few keystrokes.

Related functions are grouiped together in “Menues”. The

selected function will be highlighted in colour. In the bottom

line, coloured bars depict the function keys red, yellow, green

and blue. These colour bars represent different functions in

different menues, which can be executed by pressing the

appropriate coloured key (multi-function key) on the remote

control unit. The function keys are only active when a brief

description is displayed in the appropriate field.

Help function:

Where available.in a menu,pressing the blue function key

will display a help text - press again to close the display

window.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 7

Key description and terms that appear in the OSD menu are

denoted in this manual in bold type.

Environmental note:

The packaging of your unit consists exclusively of recyclable

materials. Please dispose of the packaging in the appropriate

manner (Dual System in Germany).

Please ensure that spent batteries from the remote control as

well as any electronic components are not disposed of in

domestic refuse, but are dealt with appropriately (disposal

through retailer, local authority).

Safety Note:

For your own protection, you should read these security

notes carefully before you commence operating your new

receiver.

The manufacturer accepts no liability for damage caused by

inappropriate handling or through failure to observe the secu-

rity precautions.

In order to ensure adequate ventilation, place the unit

on a smooth, straight and level surface, and do not

place any objects on top of the unit. Ventilation slits

are provided on top of the unit to allow warm air to

radiate out of the unit.

Do not place any burning items, such as lighted cand-

les, on top of the unit.

Do not expose the unit to dripping water or water

sprays, and do not place any vases or other

receptacles filled with water on top of the set.

The unit should only be operated in a temperate

climate.

Do not open the unit housing! You are in danger of

receiving an electric shock. If it is necessary to open

the housing, this should be effected by trained person-

nel only.

In the following cases you should disconnect the unit

from the power mains and consult a trained specialist:

when the mains cable or the mains plug are damaged

if the unit was exposed to humidity or liquid, or if liquid

has entered the housing

in case of significant external damage

When not in operation:

During electric storms, or when the unit is not being used for

an extended period of time, it should be disconnected from

the mains power.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 8

Connecting the DVB receiver to a satellite

installation

a. Connect the LNB to the LNB input (LNB IN)of the

DVB receiver.

b. Mains power connection

c. Connect the SCART output of a video recorder to the VCR

Scart socket of the DVB receiver.

d. Connect the Scart connection of the DVB receiver with the

television set.

e. Connect the LNB output (LNB OUT) to the LNB input of

an analogue receiver.

Analogue Receiver

VCR

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 9

4 Connections

The references a b c etc. below refer to the illustration on

page 8.

4.1 Mains power connection

The receiver should be connected to the mains power supply

only once all other connections with the approrpiate units

have been made. This will ensure that the receiver and the

other components are not damaged.

When you have made all the above connections, use

the enclosed mains power cable to connect the

receiver to a mains power outlet with 230V/50 Hz AC

power.

4.2 External unit

4.2.1 Single unit operation

Using a suitable coaxial cable, connect the LNB

input of the receiver with the LNB of your external

unit. Also note Point 5 "Installation".

4.2.2 Operating an additional receiver in a single-

receiver installation

If you wish to operate another appliance in a single-

receiver installation (e.g. analogue receiver or ADR

receiver),you may connect the LNB input of the

additional receiver with the LNB output of the DVB

receiver by means of a suitable coaxial cable. In order

for the satellite signal to be available to the additional

receiver, your DVB receiver must be set to standby

mode. If the DVB receiver is switched on, this will

receive signal priority from the LNB control.

4.3 Connection to a television set

Use a SCART cable to connect the receiver (SCART

socket TV) and the television set (SCART socket).

If your television set is equipped for this, it will switch

automatically to AV mode, and thus to satellite

reception, when switched on.

4.4 Video cassette recorder (VCR)

Connect the video recorder to the SCART socket

VCR . In playback mode the video recorder will

supply a switching signal to the receiver.

The video recorder signal will then be fed

automatically to the TV set.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 10

If your video recorder does not provide an electric

signal, use the EXTERN key to switch your receiver

to the external VCR input. Pressing this key again will

revert to normal operation.

4.5 Hi-fi amplifier

To achieve the best sound quality, the receiver can be

connected to a hi-fi amplifier. To do this, connect the Audio

R and Audio L cinch sockets of the receiver with a suitable

input of your hi-fi amplifier, e.g. CD or AUX, using a suitable

cable. Note that the Phono imput is not suitable!.

4.6 Serial interface RS 232

The RS 232 interface serves to update the operating

software, and to facilitate pre-programming by means of a

PC.

5 Installation

Once you have connected your receiver, and have

commenced operation, you can proceed to optimize the

settings for your personal preferences, if you wish.

5.1 OSD language

This feature gives you the opportunity to set the menu

language in accordance with your preferences.

To change the OSD language, proceed as follows:

Press the Menu key to display the Main Menu (Fig.

5-1).

Now use the arrow keys up/down to select the menu

item OSD language.

Confirm by pressing OK.

The sub-menu OSD language will be displayed.

Use the arrow up/down keys to select the desired

language. Use the arrow up/down keys to move

the marker up or down one line at a time, use the

arrow keys left/right to move forward or back one

page at a time.

(Fig. 5-1)

Store your selection in memory by pressing OK.

Press the Back key to return to the Main Menu.

5.2 Basic settings

In order to gain optimum enjoyment from your DVB receiver,

you may still have to adjust some settings to your individual

preferences.

Press the Menu key to display the Main Menu.

Use the arrow keys up/down to select the line

Settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 11

Confirm by pressing OK. The sub-menu Settings will

be displayed. (Fig. 5-2)

Now use the arrow keys up/down to select the entry

Basic Settings.

Confirm by pressing OK. The menu Basic Settings

will be displayed. (Fig. 5-3)

Use the arrow keys up/down to move the marker

around within this menu, and to make changes in

individual positions according to your preference.

When selecting a menu item please also note any

help text displayed.

(Fig. 5-2)

The following settings can be customized:

5.2.1 Parental control

Your unit is equipped with a child-proof function. This means

that any programmes that you have blocked from access as

described under Points 7.1.5 and 7.2 can only be selected

after entering a four-digit PIN code. In this line you can press

the OK key to switch the child-proof feature on or off.

5.2.2 Time difference GMT (hours)

Your unit is equipped with an integrated clock. This is set via

satellite reception to Greenwich Mean Time. If you have

select None under Country (see 5.2.3), you merely need to

use the arrow keys right/left or the OK key to correct the

clock to your local time. In Germany the difference for

standard time is +1 hour, for daylight savings time the

difference is +2 hours.

(Fig. 5-3)

5.2.3 Country

This function provides for automatic change-overs from

daylight saving time to standard time. Enter your home

country in the line Country, using the arrow keys left/right

to select the appropriate country.

Press the Back key to return to the menu Settings, or

press the Menu key to return to normal operation. The

settings will be automatically stored in memory.

5.3 Audio/Video settings

In order to optimize the receiver in cojunction with your

television set, you can effect the following settings in the

menu Audio/Video Settings.

Press the Menu key to display the Main Menu.

Use the arrow keys up/down to select the line

Settings.

Confirm by pressing OK. The sub-menu Settings will

be displayed. (Fig. 5-4)

Now use the arrow keys up/down to mark the line

Audio/Video Settings.

(Fig. 5-4)

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 12

Confirm by pressing OK.

The menu Audio/Video Settings will be displayed.

(Fig. 5-5)

Use the arrow keys up/down to move around in this

menu, and to change the individual items as indicated.

Where indicated, please take note of the help text

displayed in conjunction with your selection.

The following settings can be effected:

5.3.1 Image format TV set:

(Fig. 5-5)

Use the arrow keys up/down to set the appropriate image

format for your TV set: 4:3 or 16:9. This function allows the

image format to be adapted to your TV set automatically.

5.3.2 Language (Audio signal)

Use the arrow keys left/right in this line to select your

preferred language. Whenever this is broadcast (dual-tone

broadcasts) this will be selected automatically.

5.3.3 SCART mode

Use the arrow keys left/right in this line to select the setting

appropriate for your TV set, FBAS or RGB. For standard

sets retain the default setting RGB.

Press the Back key to return to the menu Settings, or

press the Menu key to return to normal operation. The

settings will be automatically stored in memory.

5.4 LNB setting/Adjusting to external

unit/Satellite selection

When you have completed customizing the settings of your

receiver to your preferences, it may be necessary to adjust

the receiver to your antenna. The receiver is programmed at

the factory with all the ASTRA and EUTELSAT programmes,

and configured for a Universal LNB (see Anexure Technical

terms). These programmes can be received via an

appropriate antenna immediately after commencing operation

of your receiver, without any further adjustments.

(Fig. 5-6)

If you wish to receive signals from other satellites, or if you

are using a different type of LNB,. you can make the

necessary adjustments to your receiver settings as follows:

Press the Menu key to display the Main Menu. (Fig.

5-6)

Use the arrow keys up/down to select the line

Settings.

Confirm by pressing OK.

The menu Settings will be displayed. (Fig. 5-7)

Now use the arrow keys up/down to select the line

LNB Settings.

(Fig. 5-7)

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 13

Confirm by pressing OK. The menu LNB Settings

will be displayed. (Fig. 5-8)

The following settings can be effected in this sub-menu:

5.4.1 Switching DiSEqC on and off

DiSEqC (Digital Satelliten Equipment Control) is a digital

switching signal used to control DiSEqC-compatible

components via the antenna connection.

If your external unit is equipped with DiSEqC componen ts

you must activate the DiSEqC switching:

In this line, use the OK key to switch the DiSEqC on

or off.

As only one LNB can be controlled when the DiSEqC

switching is not activated, the menu will be restricted

to the configuration of a single LNB.

(Fig. 5-8)

5.4.2 Setting the switching matrix and the LNB

characteristics

The menu lists the four switching criteria of the DiSEqC

switching feature.

Your unit is pre-programmed so that ASTRA will be received

in switch position A/A and Eutelsat will be received on switch

position B/A of a multi-switch. Should the switching matrix of

your receiving installation be configured differently, or if you

wish to receive other satellites, you can adjust your receiver

to the parameters of your receiving installation as follows.

Use the arrow keys up/down to select the DiSEqC

switch position (1-4) to which you wish to assign a

satellite, by marking this line in blue (e.g.. A/B 3 No

Satellite).

Example:

Press OK.

A table showing the satellites available for selection

will be displayed.

Use the arrow keys up/down to mark the required

satellite.

Use the arrow keys up/down to move up or down the

menu one line at a time, use the arrow keys left/right

to move forward or back one page at a time.

Should the satellite you require not be listed, please

select one of the reserve slots, designated User1 to

User 14.

Position

Output

Option

Output

Confirm by pressing OK. The selected satellite will

now be inserted at the previously marked poosition in

the menu LNB Settings.

You should now proceed to work through the menu LNB

Settings, until the settings in this menu correspond with the

characteristics of your receiving installation. In the case of

any switching criteria you do not require, select the option

No Satellite.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 14

5.4.3 Additional Settings

Once you have adjusted the switching matrix of your DVB

receiver to the requirements of your receiving installation,

you should now check and, if necessary, correct the other

settings relating to your receiving unit.

Use the arrow keys left/right to move the marker to

the item LNB Test.

Now, in the line whose setting you wish to change, use

the arrow keys up/down to select the field

Continue.

(Fig. 5-9)

Confirm by pressing OK. The menu LNB Settings

will be displayed.(Fig. 5-9)

The following settings can be effected in this menu:

DiSEqC Type

In this line, use the arrow keys left/right to select the

type of LNB you are using. You can choose from

Single LNB, Quatro LNB, DisiCon 1 LNB,

DisiCon 2 LNB, DisiCon 4 LNB, C-Band LNB

and a User LNB, for manual entry of LNB data.

Press OK to accept the setting and store it in memory.

Test Transponder

The following items of this menu should only be entered when

you wish to test the signal of a particular satellite.

Transponder frequency

In this line, use the numeric keys to enter a frequency on

which digital programmes are broadcast.

Polarisation

Use the arrow keys up/down to enter the desired polarisati-

on plane (horizontal or vertical).

Symbol rate

The symbol rate indicates the volume of data transmitted per

second. For example, this could be 27500 (27500 symbols

per second). Use the numeric keys to enter the appropriate

value.

User LNB

If you have selected the DiSEqC Type User LNB, you can

select further parameters:

LOF low band

LOF (Local oscillator frequency) is the frequency used to

convert the received frequency into the so-called 1.

intermediate frequency, which can then be interpreted by the

receiver. So-called Universal LNBs utilize 2 LOFs to cover the

entire reception range of 10.7 to 11,8 GHz (low-band) and

11,7 to 12,75 GHz (high band).

In this line, use the numeric keys to enter the LOF of

the low band of your LNB.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 15

LOF high band

In this line, use the numeric keys to enter the LOF of the

high band of your LNB.

Switchover LOF low//high

In this line, use the numeric keys to enter the frequency at

which your LNB switches from the low band to the high band.

Press OK to accept the setting and store it in memory.

Signal/Quality

If you have entered the parameters of the test transponder

correctly, this line will indicate the signal strength and quality.

5.4.4 Rotating antenna

If you are operating the receiver in conjunction with a rotating

antenna driven by a DiSEqC motor ( Level 1.2), switch the

DiSEqC Control (Point 5.4.1) on and please note Point

8 of the operating manmual.

6 Operation

6.1 Switching on and off

Switch the receiver on by pressing the On/Standby

key on the front panel of the unit, or on the remote

control.

Pressing the same key again - on the unit or on the

remote control - will switch the receiver off again.

The unit is now in standby mode, ready for use.

Please note:

When switching the receiver off, all current settings are

automatically stored in memory. For this reason the

unit can only be switched on again after a period of

approx. 15 seconds.

6.2 Programme selection

6.2.1 Using the Programme keys up/down

You can switch from one programme to another, one

slot at a time, using the programme keys up/down

either on the receiver itself or on the remote control

unit.

6.2.2 Using the numeric keys

You can use the numeric keys to enter the desired

programme number directly.

For example:

for programme slot 1

for programme slot 14

for programme slot 234

then 4

then 3,

then 4

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 16

When entering programme numbers with several digits, you

have approx. 3 seconds time after pressing a key to complete

the entry.

If you wish to enter a number consisting of a single or two

digits, you can speed up the switching process by keeping the

last digit depressed. for a few seconds.

6.2.3 Using the programme list

Press the OK key.

The programme list will now be displayed. (Fig. 6-1)

In TV mode, only TV programmes will be displayed, and in

Radio mode only radio programmes will be shown. The

programme currently selected will be highlighted in yellow.

You can now highlight the desired programme, using

the arrow keys up/down.

Press OK to switch to the selected programme.

Use the arrow keys up/down to move up or down in

the list one slot at a time.

(Fig. 6-1)

Use the arrow keys left/right to move through the list

one page at a time.

6.2.3.1 Selecting a list

In order to facilitate the easy location of programmes, the

receiver features several programme lists. You can use a list

of your own personal Favourites (see Point 7.1), or you can

have the programmes displayed alphabetically or sorted

according to providers.

Press OK. The active programme list will be

displayed.

(Fig. 6-2)

Now press the red function key to open a window

showing the types of programme list available

(Favourites List, Providers and ABC ...).The

active programme list type is highlighted. (Fig. 6-2)

Use the arrow keys up/down to select, for instance,

the programme list type ABC and confirm by

pressing OK.

The alphabetically sorted programme list will be

displayed, containing all programmes. (Fig. 6-3)

Use the arrow keys up/down to mark the programme

you wish to view.

(Fig. 6-3)

Confirm by pressing OK.

6.2.4 Calling up blocked programmes

If a programme is selected that is protected by the parental

control function, a window will be displayed on the screen

“Enter PIN” .

Use the numeric keys to enter your PIN code.

The selected programme can now be viewed.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 17

To make operation more convenient, you will only be asked to

enter the PIN code once while the receiver is in operation, the

programme remains unblocked for the remainder of the

session. The parental control feature only becomes active

again the next time the receiver is switched on.

6.2.5 Information box

Each time you switch programmes, an information box will be

displayed briefly (Fig. 6-4) showing the programme slot and

the programme name. In addition, other programme characte-

ristics are indicated, such as TxT for vide otext, 16/9 for a

programme in 16/9 format, A/B for various audio channels

(e,g, a film synchronised in several languages, or various

radio programmes) and a key symbol to indicate encrypted

programmes.

(Fig. 6-4)

6.3 Volume control

You have the facility to vary the volume of your receiver. This

makes for easy, convernient operation, since all important

functions are thus combined on one remote control, so that

you willhave to use the remote control of your television set

only rarely. When the receiver is switched on, sound will be

reproduced at the volume level last selected.

Use the keys Volume + (louder) and Volume - (softer)

to regulate the volume of your receiver.

Press the key Sound on/off to switch the sound off

(mute), press the key again to switch sound on again.

6.4 Reception of encrypted programmes

Your receiver is equipped with a Common Interface. To

receive encrypted programmes with this, you must obtain a

CA module as well as a valid smart card, and insert these in

the appropriate slot provided on the rear panel:

Insert a CA module in the slot.

Insert the smart card in the card slot of the CA

module. Ensure that the gold-coloured chip of the

smart card is located on the upper side of the card, in

the direction in which it is inserted.

If an encrypted programme is selected for viewing, the

receiver will automatically check the card slot, and will

display the programme in unencrypted form, provided

that a corresponding CA module and the

corresponding valid smart card are inserted.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 18

6.4.1 Multifeed options

Some programmes (e.g. Premiere Sport) provide the option of

(Fig. 6-5)

multifeed reception. This feature allows you, for instance, to

view a sports event from the viewpoint of various camera

angles, which you can select at will (e.g. Formula 1 racing) or

to switch to various locations for the same sport (e.g. National

Football League games). Where a programme, e.g. Sport 1,

offers multifeed options, the window Camera (Fig. 6-5) will be

displayed.

(Fig. 6-6)

To select one of the available options, press the Info

key. An information window with the available options

will be displayed. (Fig. 6-6)

Use the arrow keys up/down to select the desired

option.

Confirm by pressing OK.

Your receiver will now display the selected option.

6.4.2 Time control (Near Video On Demand)

Other channels (e.g. the PREMIERE DIREKT channels) offer

the facility of time control. In this case, movies are available

round the clock at staggered starting times.

(Fig. 6-7)

Where a programme provides time control, this will be

indicated by the display of an information window Time

Control (Fig. 6-7).

(Fig. 6-8)

To select on of the starting times available, press the

Info key.

A window showing the available starting times will be

displayed (Fig. 6-8).

Use the arrow keys up/down to select the desired

starting time.

Confirm by pressing OK.

If the programme availability has been confirmed, you

will be able to view it at the selected starting time. Also

refer to the programme guide of your provider for

details.

6.5 Selecting a different language

Where a programme is broadcast in several languages, or

with several sound channels (

in the information window)

you can select a different language or a different sound

channel as follows:

Press the key Language Select. Where available, a

list of the currently broadcast languages will be

displayed on the TV screen.

Use the arrow keys up/down to select the preferred

language.

Confirm by pressing OK.

You can now enjoy the programme in the desired language.

You receiver is also equipped to receive mono broadcasts.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 19

6.6 Switching between TV and Radio

The pre-programming feature includes television programmes

as well as radio programmes. If the latter are selected, the

TV image is switched off, and the screen displays only the

programme name.

Use the TV/Radio key to switch the receiver into

radio mode. The receiver will go to the last radio

programme selected.

Pressing the TV/Radio key again will return you to

the television programme last viewed.

6.7 Return to previous programme

Press the Back key on the remote control to return to

the previously selected programme.

Press the key again to revert to the programme

viewed before the switch.

6.8 Display clock and programme information

This function allows you to display programme information

related to the programme currently selected.

Press the blue function key to display information for

the programme currently selected.

On the lower half of the screen you will see a display showing

the current time, the name of the current programme,

including the start and end times of the programme, where

these are broadcast by the provider.

Where the information is available from the provider,

pressing the blue function key again will display

information relating to the following programme.

6.9 Additional programme information

Where broadcast by the provider, you can obtain additional

programme information by pressing the function

Programme info.

Press the yellow function key to open an additional

information window.

This will again display information relating to the

current programme.

Press the yellow function key again to display

information on the following programme.

Press the yellow key again to remove the information

window display and return to normal operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 20

6.10 Transponder Information

Press the green function key (Transponder

Information), to display the data relating to the

currently selected transponder (Fig. 6-9).

Press the green function key again to exit from

transponder information.

6.11 Electronic Programme Guide

The Electronic Programme Guide function allows you to

display programme schedules as well as content descriptions

of various programmes on the television screen. You can thus

very quickly obtain an overview of current programmes as

well as of the schedule for the remainder of the day and the

next few days, wherever this information is provided

(Fig. 6-9)

6.11.1 Calling up the Electronic Programme Guide

Switch on both the receiver and your TV set.

Press the EPG key on the remote control of your

receiver.The electronic programme guide for the TV

channel currently being viewed will be displayed on

your screen. This includes data relating to the

programme for the current day (Fig. 6-10).

The following functions are available:

6.11.2 Programme preview for following days

(Fig. 6-10)

Wherever this information is provided, you can obtain infor-

mation on the programm contents for the next few days rela-

ting to the channel currently selected, by pressing the arrow

key right.

Pressing the arrow key left will take you back to the previous

table displayed.

6.11.3 EPG Information

Wherever this information is broadcast, the EPG function will

provide you with information on various programmes:

Use the arrow keys up/down to mark the desired

programme.

Press either the EPG key or the blue function key

(more) to display the information.

Lengthy information text can be moved by using the

arrow keys up/down, while the arrow keys

left/right can be used to move through the text a

page at a time.

Press the Back key to return to the previous table.

6.11.4 Exiting from EPG

Press the Back key to return to normal operating

mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 21

6.12 Timer

Your receiver is equipped with a timer. This allows you to

make video recordings even when you are away. The timer

mode is indicated by a blinking control LED in the display.

Timer mode can be cancelled by pressing the On/Standby

key.

6.12.1 Programming via EPG:

Switch to the programme on which the item to be

recorded is broadcast.

Press the EPG key. The EPG table of the programme

selected will be displayed.

Use the arrow keys up/down to mark the required

programme.

Press the yellow function key (Record).

The data relating to the marked programme will now

be stored in the timer memory, and will be displayed

on screen for control purposes. (Fig. 6-11)

To delete a marked timer, press the green function key

(Delete) and confirm when asked to do so on screen.

Press the Back key to return to the EPG table, and, if

you wish, to programme additional timer events

(Fig. 6-11)

Press the TV/Radio key to return to normal

operation.

The receiver will now select the appropriate programme at

the programmed time, and will, if instructed to do so, revert to

stand-by mode at the end of the programme.

6.12.2 Manual programming/Changing timer set-

tings

In addition to EPG timer programming you can also carry out

manual programming of the timer. To do this, proceed as

follows:

Press the Menu key to display the Main Menu.

Mark the item Timer and confirm by pressing OK.

The Timer menu will be displayed. (Fig. 6-12)

Press the yellow function key (New) to go to timer

programming, in order to programme a new timer

event. (Fig. 6-13)

To alter an existing timer setting, mark this by using

the arrow keys up/down. Press the yellow function

key (Change) to access the settings of the marked

timer.

(Fig. 6-12)

For programming, proceed as follows:

Source

Use the arrow keys to mark the item Source, then

use the OK key to enter the required source (TV or

Radio).

(Fig. 6-13)

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 22

Channel

In this line, select the television channel/station on which you

wish to record a programme:

If necessary, use the arrow keys to mark the

Channel.

Press OK. A programme list will be displayed.

Use the arrow keys to mark the desired programme.

Confirm by pressing OK.

The selected programme will now be accepted into the

timer menu.

Date

Use the arrow keys to mark the item Date.

Use the numeric keys to enter the recording date.

Start

Use the arrow key right to select the item Start.

In this line use the numeric keys to enter the starting

time.

Stop

Repeat the steps as described under “Start” to enter

the stop time, or end of programme.

So that all events can be included, there should be an

interval of at least one minute between the stop time of a

timer event and the starting time of the next timer event!

Repeat (optional)

Use the arrow key right to mark the item Rep.

Press OK.

A selection window will be displayed, offering various

repeating suggestions.

Timer on

Daily repeat

1xW Repeat once a week

1-5 Repeat only on weekday

6-7 Repeat only on weekends

Use the arrow keys up/down to select the desired

function.

Press OK to accept the setting into memory.

When you have completed the programming, press

the yellow function key (Accept) to accept and store

the data in memory.

Press the TV/Radio key to return to normal

operation.

Type

Use the arrow key right to mark the item Type.

Use the OK key to enter the required type in this line.

VCR

Your receiver will be switched on resp. off for the

selected programme. If the receiver is switched on by

means of the timer, most of the functions of the remote

control are disabled, as a safety precaution to prevent

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 23

inadvertent interruption of the recording.

Timer operation is indicated by blinking of the control

LED on the display.

Preselect

Your receiver switches itself on at the set time, and

selects the appropriate channel. In contrast to the

VCR setting, all functions of the remote control remain

active, and the unit does not switch off at the end of

the recording.

Note!!!

Please ensure that the information box shows the correct

time. If this is not the case, switch your receiver to ZDF or

any other channel providing standard clock time for at least

30 seconds, to allow the unit to synchronize with the correct

time.

6.13 Video text

6.13.1 Using the video text decoder of your

television set

Where available from the provider, video text will be available

on your TV set. To operate the video text function use the

remote control of your television set. Should you experience

any problems with your television set, such as graphics and

text being superimposed, switch your receiver to FBAS

mode (Point 5.3).

6.13.2 Using the internal video text decoder

If your television set is not equipped with an integrated video

text decoder, you can still receive video text, where broadcast

by the provider, through your receiver.

Select the programme on which you wish to view

video text information.

Press the red function key to switch on video text.

(Fig. 6-14)

Use the numeric keys to enter the video text page

you wish to view. Your input will be displayed in the

upper left corner of the screen.

(Fig. 6-14)

When you have entered the desired page number, the

receiver will search for the selected page. As not all

pages can be transmitted simultaneously, it may take

a few seconds before your receiver finds the page and

displays it on the TV screen.

All video text providers use page 100 for their

index/list of contents.

Press the red resp. green function keys to move

forward resp. backward in the text one page at a time.

Press the Back key to return to normal operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 24

7 Changing basic programming

7.1 Configuring the programme list This chapter

describes how you can change the pre-programming as well

as the Favourites list of your receiver to reflect your personal

preferences. This function is also required to sort newly found

programmes into the list after a programme search.

For your information, your receiver is equipped with two

programme lists, the Favourites List and the Total List. The

Favourites programme list includes all programmes you have

taken into the list by the following procedure. The Total list

includes all programmes.

This chapter also describes how you can delete programmes,

or how you can block access by means of the parental control

function. When calling up the programme list by pressing the

OK key, the Favourites programme list will be displayed.

When the receiver is in TV mode you can view and change

the list of TV programmes, and you can view and change the

radio programmes in Radio mode.

7.1.1 Calling up the programme list

Press OK.

The Favourites programme list will be displayed. (Fig.

7-1)

7.1.2 Adding programmes to the programme list

To add programmes to the programme list selected, proceed

as follows:

Press the red function key (Category) to open a

selection window that will allow you to switch from the

Favourites list to the Total list. This Total list contains

all available programmes. You can choose to sort the

Total list according to Providers or alphabetically

(ABC...).

(Fig. 7-1)

Use the arrow keys up/down to select a programme

sorting type. (e.g. ABC)

Confirm by pressing OK.

An alphabetically sorted list will now be displayed.

(Fig. 7-2)

Press the green function key (Select) to display a

selection window (Fig. 7-3).

Now use the arrow keys up/down to select the item

All, to display all available programmes in the Total

list, or All new, to display only the new programmes

found by the last programme search.

(Fig. 7-2)

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 25

Confirm by pressing OK. Now, depending on your sel-

ection, a programme list showing either all program-

mes or all new programmes will be displayed. Pro-

grammes already included in the Favourites list will be

indicated by a check-mark. (Fig. 7-4)

To add programmes to the Favourites list, or to delete them

from the list, proceed as follows:

Press the blue function key (Change).

Use the arrow keys up/down to mark a programme

you wish to add to the list.

(Fig. 7-3)

Press the green function key (Add) to add the marked

programme to the Favourites list.

To mark several programmes simultaneously, proceed

as follows:

Press the OK key to go to selection mode. The

marked programme will now be indicated by a cross

on the left hand margin, and the menu will be

displayed in transparent form, superimposed on the

background image.

(Fig. 7-4)

Now use the arrow keys up/down to mark additional

programmes of your choice.

When you have completed selecting and marking

programmes, press the green function key (Add) to

add the programmes to the Favourites list.

7.1.3 Deleting programmes

7.1.3.1 Deleting from the Favourites list

If the above procedure is used to mark programmes with a

cross that are already included in the Favourites list (check-

mark at right), these marked programmes can be deleted

from the user table by pressing the green function key. These

programmes remain stored in the Total list, and can be added

to the Favourites list again at any time.

7.1.3.2 Deleting from the Total list

To delete marked programmes from the Total list, press the

red function key (Delete). You will be asked to confirm the

command, then the programme will be deleted from the Total

list.

Mark the programmes you wish to delete as described

above.

Press the red function key (Delete). The following will

be displayed on screen “Do you really want to delete

the programme(s)?”.

Use the arrow keys left/right to select Yes or No.

Confirm by pressing OK.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 26

7.1.4 Sorting programmes

To sort the programmes on your Favourites list in the order

you prefer, proceed as follows:

Press OK to display the Favourites list.

Press the blue function key (Change) to go to the

programme list (Fig. 7-5).

Use the arrow keys up/down to mark the programme

you wish to place at a different position in the list.

Press the yellow function key to select the Sort

function.

(Fig. 7-5)

A double arrow will be displayed next to the

programme selected.

You can now position the selected programme at any

desired position in the programme list, using the arrow

keys up/down or the numeric keys.

Press the yellow function key (Save) to store the

programme at the new position.

To mark several programmes simultaneously, proceed

as follows:

Press OK to go to Select mode.

The selected programme will now be indicated by a

cross in the left margin.

Now, use the arrow keys up/down to select additional

programmes of your choice.

When you have completed marking programmes in

this manner, press the yellow function key (Sort).

You can now use the arrow keys up/down and/or the

numeric keys to move the marked programmes to the

desired position in the programme list.

Press the yellow function key (Save) to store the

programmes at the new position.

When you have completed configuring the programme

list according to your preferences, press the Back key

twice to return to normal operation.

7.1.5 Blocking access to programmes (parental

control)

You have the facility to block access to any programme. A

blocked programme can only be displayed on screen if the

personal PIN code is entered after the programme has been

selected. Once this code has been entered, the programme

remains unblocked for the entire viewing session, i.e. until it is

switched off, resp. switched into standby mode.

To block access to a programme, proceed as follows:

Press OK to display a programme list.

Press the blue function key (Change).

Now use the arrow keys up/down to mark the

programme to which you wish to block the access.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 27

Use the green function key to select the function

Parental Control.

A key symbol will be displayed next to the selected

programme.

Repeat this procedure until you have blocked access

to all the programmes you wish to mark in this way.

When you have completed configuring the programme

list according to your preferences, press the Back key

twice to return to normal operation.

To activate the parental control function, you must now

enter your personal PIN code in the Point Changing

PIN, you must then activate the parental control

function as described in Point 5.2 (Basic Settings).

7.2 Changing the PIN

The Pin code is set at the factory (default value) to 0000. In

order to activate the parental control feature, you must input

your own personal PIN code instead of the default setting.

Note! Be sure not to forget your PIN code.If this

should happen, consult your specialist retailer!

To change the PIN code proceed as follows:

Press the Menu key to display the Main Menu.

Use the arrow keys up/down to mark the item

Settings.

(Fig. 7-6)

Confirm by pressing OK.

The sub-menu Settings will be displayed.

Use the arrow keys up/down to mark the item

Change Unit PIN.

Confirm by pressing OK. The menu Change Unit

PIN will be displayed. (Fig. 7-6).

Now use the numeric keys to enter the current PIN

code (default setting 0000).

Use the numeric keys to enter the new PIN code you

have chosen.

Repeat entry of the new code.

You have completed changing the PIN code. Press

Back twice to return to normal operation.

Please note that you must still activate the parental control

function as described under Point 7.3.

7.3 Unblocking access control for individual

programmes

To delete the parental control function for individual

programmes, proceed as described under Point 7.1.5. Press

the blue function key (Change), then enter the appropriate

PIN code. Select the programme you wish to unblock, and

remove the access control by pressing the green function

key (Parental Control).

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 28

7.4 Programme Search

As mentioned previously, your receiver is pre-programmed for

all programmes available on the ASTRA and EUTELSAT

satellites. To receive new programmes, or those of other

satellites, several options are available to carry out a

programme search/scan.

1.Satellite:

All, to search all satellites selected in the menu LNB

Settings (Point 5.4) for programmes

Satellite, to scan only the selected satellite for

programmes and bouquets.

(Fig. 7-7)

2.Transponder:

Select this scan/search function to scan only a specific

transponder of a satellite. This will search for individual resp.

all programmes of a transponder.

3.Manual Search

Use this type of search to search for for specific programmes

for which you have the unique PID numbers available.

When the search has been completed, a display will appear

on your screen, informing you how many programmes were

found and how many of these are new additions.

New programmes will be stored in the Total List. You can

then add them to your Favourites List as described under

Point 7.1.

(Fig. 7-8)

To perform a programme search call up the Main

Menu. (Fig. 7-7)

Use the arrow keys up/down to mark the item

Search.

Confirm by pressing OK.

The sub-menu Search will be displayed. (Fig. 7-8)

Use the arrow keys up/down to select the type of

search you wish to perform.

7.4.1 Satellite

Activating this type of search will scan all active satellites

(Point 5.4) and transponders for programmes.

Use the arrow keys up/down to select the menu line

Satellite.

Press OK to display the corresponding sub-menu.

(Fig. 7-9)

Press OK again to open the selection table for the

active satellites.

Use the arrow keys up/down to mark the menu line

All, to search all active satellites for programmes, or

mark a specific satellite to search only this satellite for

programmes.

(Fig. 7-9)

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 29

Press the green function key (Search mode) to decide

whether you want to search only for free-to-air

programmes (Free programmes), or whether you

want to include encrypted programmes (All

programmes).

Confirm by pressing the red function key (“Start

search”).

The search will be started. Please note any

information displayed on your screen.

Pressing the red function key again will stop the

search procedure.

A full search can take approximately 15 minutes to complete.

Please also note any information displayed on your screen.

7.4.2 Transponder

This menu item allows you to search a specific transponder

(see Point 9 Technical terms) for programmes. To do this you

will have to enter the appropriate transponder data.

Use the arrow keys up/down to select the menu item.

Confirm by pressing OK. The menu Search

Transponder will be displayed. (Fig. 7-10)

Satellite

In this line, set the satellite on which the desired transponder

is located.

(Fig. 7-10)

Use the arrow keys up/down to mark the line

Satellite.

Press OK. A table showing the active satellites will be

displayed.

Use the arrow keys up/down to mark the desired

satellite.

Confirm by pressing OK.

The selected satellite will now be displayed in the line

Satellite.

Transponder frequency

Use the arrow keys up/down to mark the line

Transponder frequency.

Using the numeric keys, enter the desired frequency

in this line.

Symbol rate

The symbol rate indicates the volume of data transmitted per

second. This value can be, for example, 27500 (27500

symbols per second).

Use the arrow keys up/down to mark the item

Symbol rate.

Use the numeric keys to enter the appropriate symbol

rate.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 30

Polarisation

Use the arrow keys up/down to mark the item

Polarisation.

Use the OK key to enter the polarisation plane

(horizontal or vertical) on which the desired

programme is broadcast.

Press the green function key to decide whether you

wish to search only for free-to-air programmes (Free

programmes) or whether you wish to include encryp-

ted programmes (All programmes) in the search.

Press the red function key (Start search) to commence

the search..

The search will be started. Please note any

information displayed on your screen.

The search procedure can be stopped by again

pressing the red function key.

7.4.3 Manual search

If you are unable to find a programme using the search

methods as described under Points 7.4.1 and 7.4.2, it may be

necessary to enter additional unique. and programme-specific

PID numbers. These numbers can be found in the Internet, or

you can contact the respective programme providers for this

information.

To perform a manual search, call up the menu Search

Manual Search. (Fig. 7-11)

Use the arrow keys up/down to select the menu item

Manual Search.

(Fig. 7-11)

Confirm by pressing OK.

The menu >Search>Manual Search will be

displayed.

The menu differs from the menu Transponder only with

respect to the menu items PCR PID, Audio PID and

Video PID.

Proceed as described under Point 7.4.3.

Use the arrow keys up/down to mark the lines PCR

PID, Audio PID and Video PID, then use the

numeric keys to enter the corresponding numbers.

7.4.4 Integrating programmes after a search

As the search of one or more transponders progresses, you

can follow this on the screen. When the search has been

completed, the number of transponders found, will be display-

ed. In addition, you will be asked by the display (Fig. 7-12)

whether you wish to integrate the programmes found automa-

tically in the TV or radio programme lists. If you wish to incor-

porate the programmes automatically, you can decide

whether they should be added to the Favourites list in sor-

ted or unsorted order.

(Fig. 7-12)

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 31

Sorted

The new programmes found will be sorted into the Favourites

list according to a preprogrammed list.

Unsorted

The new programmes found will be added in unsorted order

at the end of the Favourites list.

The new programmes found will not be added to the

Favourites list.

Use the arrow keys left/right to indicate whether

you want to add the programmes in sorted or unsorted form.

Confirm by pressing OK.

Please take note of any additional information

displayed on screen.

Press Menu to return to normal operation

Independently of whether you have added the newly

found programmes to the Favourites list automatically,

you can also, as described in Chapter 7.1, add these

to the Favourites list manually at any time.

7.5 Restoring basic programming/ Delete all

You can revert to the original default setting for the LNB at

any time. Also, if the programme list is out of date because of

changes made by the providers, you can delete this list

completely, in order to perform a new programme search.

Please note that if you have performed the delete function

you must first start a new programme search, and must then

copy the programmes you wish to view from the Total list to

the Favourites list before proceeding further.

(Fig. 7-13)

Press Menu to display the Main Menu.

Use the arrow keys up/down to select the menu item

Settings.

Confirm by pressing OK. The sub-menu Settings will

be displayed.(Fig. 7-13)

Use the arrow keys up/down to mark the menu item

Default setting.

Confirm by pressing OK. The sub-menu Default

setting will be displayed. (Fig. 7-14)

7.5.1 Activating default setting

This function allows you to revert to the default setting

programmed in the factory. It also deletes your own personal

settings.

Use the arrow keys up/down to mark the item

Activate default setting.

Press OK. The message “Do you really want to

activate the default setting?” will be displayed.

Use the arrow keys left/right to select Yes or No.

Confirm by pressing OK.

(Fig. 7-14)

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 32

7.5.2 Delete all programmes

This function allows you to delete totally the programme

memory banks.

Use the arrow keys up/down to mark the line Delete

all programmes.

Press OK. The message “Do you really want to delete

all programmes?” will be displayed

Use the arrow keys left/right to indicate Yes or

Abort.

Confirm by pressing OK.

Please note any messages displayed on your screen.

7.5.3 Updating software

In addition, you have the facility to update the operating

software of your receiver via satellite (ASTRA 19° East).

Use the arrow keys up/down to mark the item

Update software.

Press OK. The sub-menu Update software will be

displayed. (Fig. 7-15)

To update your software, mark the item Update

software.

Use the OK key to switch the software update function

On.

Press the Menu key to return to normal operation.

(Fig. 7-15)

In order for the new software to be downloaded

overnight, the receiver must remain in stand-by

mode.The download procedure is indicated by a

blinking LED light on the unit.This procedure

must not be interrupted by switching the unit on

or off, nor may it be disconnected from the mains

power supply.

To start the update of the operating software manually,

press the red function key (Test) in the menu

Software Update .

To download any new software that may be available,

follow the instructions displayed on your screen.

Should the parameters of the data channel used to download

software updates have changed, you can correct them in this

menu as described under Point 7.4.3 (manual programme

search). Current transponder data can be obtained from your

specialist retailer. In general, however, you should not make

any changes in this menu.

Note:

This function should not be activated if you have

made changes in the menues “Basic Settings”

and “LNB configuration”, as any changes made

there would be deleted when this function is

performed, and you would have to repeat the

changes there

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 33

7.6 System configuration

You can use this menu item to view the specific unit data.

Use the arrow keys up/down to mark this line in the

sub-menu Settings.

Confirm by pressing OK.

Press the Menu key to return to normal operation.

7.7 Encryption system

Use this menu item to go to the sub-menues related to the

CA module. Use the arrow keys to mark the CA module, then

confirm by pressing OK to obtain information on the card

currently inserted.

8 Operation in conjunction with a rotary

antenna

Your receiver is equipped to operate in conjunction with a

rotary antenna. The DiSEqC control feature (DiSEqC-Level

1.2) allows you to control an appropriate motor to rotate the

antenna, via the coaxial connection.

As described in Point 5.4, call up the menu LNB

Settings (Fig. 8-1) and switch the DiSEqC control

(Point 5.4.1) to on.

Use the arrow keys up/down to select the DiSEqC

position (e.g. A/B 3) to which you wish to allocate the

motor-driven rotating antenna.

(Fig. 8-1)

Press OK to open a window allowing you to select the

Satellites resp. the Motor antenna . (Fig. 8-2)

Use the arrow keys up/down to select the item

Motor antenna.

Confirm by pressing OK.

Observe the message displayed (Fig. 8-3) regarding

the setting of East and West limits, confirm by

pressing OK.

(Fig. 8-2)

8.1 Eastern and Western limits

To avoid mechanical damage to the antenna dish or to the

LNB, caused by obstacles that may be in the way, you should

determine the maximum rotating range in both easterly and

westerly direction.Where there are structural obstacles, such

as chimneys or walls, these must definitely be considered

when setting the East-West limits. If there are no obstacles in

the rotating range, then you should determine the limits in

such a way that they are just a little beyond the most extreme

positions of the satellites from which you wish to receive

signals.

(Fig. 8-3)

8.1.1 Deleting existing limits

You should first delete any existing limits set.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 34

Use the arrow keys left/right to mark the item LNB

test.

Use the arrow keys up/down to go to the line Motor

antenna, and mark the field Continue.

Confirm by pressing OK.

The menu relating to settings for the motor antenna

will be displayed (Fig. 8-4)

Press the yellow function key (Action) to open a

further window. (Fig. 8-5)

Use the arrow keys up/down to mark the item Delete

limits.

Confirm by pressing OK, to transfer the selected

action to the green function key.

To delete the limits, press the green function key

(Delete limits).

A note will be displayed. Confirm by pressing OK (Fig.

8-6).

(Fig. 8-4)

(Fig. 8-5)

8.1.2 Setting Eastern limit

To enter the Eastern limit, use the arrow keys to mark

the field Save.

Press the arrow key right to turn the antenna to the

most easterly position possible, resp. the most

easterly position you wish to include.

Press the yellow function key (Action), to open the

window showing the available actions.

Use the arrow keys up/down to mark the entry Set

East limit.

(Fig. 8-6)

(Fig. 8-7)

Confirm by pressing OK.

To set the Eastern limit, press the green function key

(East limit), a note will be displayed (Fig. 8-7), then

confirm by pressing OK.

8.1.3 Setting Western limit

To enter the Western limit, use the arrow keys to

mark the field Save.

Using the arrow key left, rotate the dish antenna to

the most westerly position possible, resp. to the

most westerly position you wish to include.

Press the yellow function key (Actions) to open the

window listing all the available actions.

Use the arrow keys up/down to mark the item Set

West limit.

(Fig. 8-8)

Confirm by pressing OK.

To set the Western limit, press the green function key

(West limit), a note will be displayed (Fig. 8-8), then

confirm by pressing OK.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 35

8.2 Geo-positioning

If you have a suitable motor and know the geographic co-

ordinates of your location, this function will make it easier to

find the individual satellite positions. The co-ordinates of a

number of German cities are listed in the Annexure (Point

12).

Note! You should only switch on the geo-positioning

function if your DiSEqC motor supports this function.

As described, call up the menu LNB Settings.

Use the arrow keys to mark the field Geo.Pos.

Confirm by pressing OK. The menu used to enter the

co-ordinates of your location will be displayed. (Fig. 8-

(Fig. 8-9)

Press the OK key to switch the geo-positioning

function on or off.

Use the arrow keys to select the input field for

Longitude.

Use the numeric keys to enter your geographic

longitude.

Press the arrow key left.

In this field, press the OK key to indicate whether the

value refers to longitude East (E) or longitude West

(W).

Use the arrow keys to select the input field for

Latitude.

Use the numeric keys to enter your geographic

latitude.

Press the arrow key left.

In this field, press the OK key to indicate whether the

value refers to latitude North (N) or South (S).

Press the Back key to return to the menu LNB

Settings.

The co-ordinates for your location must be entered as a

decimal figure with one decimal place. As co-ordinates are

usually expressed in degrees, minutes and seconds, they

must be converted to decimal values as follows:

The degree figure does not change. The minutes are divided

by 60, and rounded to one decimal place. The result of this

division is added to the degree figure.

Seconds are not considered, as they have no influence on

the value of the first decimal place.

Example: Co-ordinates for Daun, Germany

Latitude

50° 11‘

(45“)

Longitude

06°

50‘

(10‘‘)

Converting the latitude (lat):

Lat.=

11/60

0,2

(rounded)

50,2

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 36

In the menu, enter the value for geographical latitude as a

decimal value correct to one decimal place (50,2) .

The decimal equivalent of the longitude can be calculated in

the same way.

8.3 Setting the satellite position

Work progressively through points 8.3.1 to 8.3.3 for each of

the satellite positions to be entered. We recommend that you

start by programming the most easterly satellite first. Then

proceed to enter each additional satellite position, working in

a westerly direction, until you reach the most westerly satellite

position.

Your receiver is programmed at the factory for the most com-

mon satellite positions. In addition you can enter and configu-

re user-defined satellite positions for any orbital position (User

1 to User 14 ).

8.3.1 Selecting satellite positions

8.3.1.1 Selecting a pre-programmed satellite

position

To enter a satellite position in the satellite list, use the

arrow keys to mark the field Sat new.

Confirm by pressingt OK.

A list of all available satellite positions will be

displayed. (Fig. 8-10)

Use the arrow keys up/down to mark a satellite

position that you wish to include in the satellite list.

Press the OK key to accept the selection into the list.

In the position Geo-positioning on (Point 8.2) the dish

antenna will now be automatically rotated to the programmed

satellite position. The rotation procedure is indicated by a

blinking message “rotating”.

(Fig. 8-10)

In the position Geo-positioning off you will have to rotate

the antenna manually to the desired satellite position (Point

8.3.2.2).

8.3.1.2 Setting user-defined satellite positions (User

Satellite)

To accept a satellite position into the satellite list, use

the arrow keys to mark the field Sat new.

Confirm by pressing OK.

A list of the available satellite positions will be

displayed. (Fig. 8-11)

Use the arrow keys up/down to mark a user-defined

satellite position (User 1 to User 14).

Press the OK key to display the menu for setting a

test transponder. In this menu, set the parameters of

the test transponder as well as of the LNB used, as

described in Point 5.4.3 .

(Fig. 8-11)

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 37

When you have entered the settings for the test

transponder, press the Back key to return to the menu

related to motor antenna settings. The field for

entering the orbital position is active.

Use the numeric keys to enter the orbital position of

the satellite and confirm by pressing OK.

Press the OK-key to indicate whether you are

entering a westerly (W) or an easterly (E) orbital

position.

In the position Geo-positioning on (Point 8.2) you can

now press Rotate to Sat (Point 8.4.1) to rotate the antenna

dish to the programmed user satellite position.

In the position Geo-positioning off you will have to rotate

the antenna manually (Point 8.3.2.2) to the required satellite

position.

8.3.2 Adjusting the satellite antenna

To adjust the antenna correctly for the satellite selected, resp.

to determine whether you can receive signals from the

satellite selected at the position you have set, a test

transponder setting is provided for each satellite.

The indication of signal strength and quality by this test

transponder allows you to align the antenna precisely.

8.3.2.1 Test-Transponder/LNB-configuration

To change the data relating to the respective test

transponder, proceed as follows:

Use the arrow keys to select the entry Current

satellite list.

Press the OK key to open the satellite list.> Use the

arrow keys up/down to select the satellite position

on which you wish to change data.

Confirm by pressing OK.

Now, use the arrow keys to select the field LNB

config. and press the OK key to confirm.

The menu LNB Settings will be displayed (Fig 8-12)

In this menu, proceed as described in Point 5.4.3 ,

and enter the data of the test transponder and of the

LNB being used.

(Fig. 8-12)

Press the Back key to return to the setting for the

motor-driven antenna.

8.3.2.2 Antenna manual adjustment

You can achieve the optimum positioning of the antenna by

referring to the signal strength and signal quality indicators

displayed. Adjust the antenna so that both bar graphs show

the maximum values..

Use the arrow keys up/down to mark the field Save.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 38

Now use the arrow keys left (Field East will be

marked) resp. right (Field West will be marked) to

rotate the dish antenna to the required position. Simply

keep the respective key depressed until the correct

position is achieved.

8.3.2.3 Automatic fine adjustment (Autofocus)

You should carry out an automatic focussing procedure

before saving the satellite position to memory. This will adjust

the antenna to optimum reception by instrument means.

(Fig. 8-13)

Press the yellow function key (Actions) to open the

window listing the available actions.

Use the arrow keys up/down to mark the item

Autofocus.

Confirm by pressing OK.

Press the green function key (Autofocus) to start the

procedure.

The message Autofocus will be displayed while the

procedure is in progress (Fig. 8-13)

8.3.3 Saving satellite positions

When the autofocus procedure has been completed, you

must still save the satellite position to memory.

Use the arrow keys to mark the field Save.

Confirm by pressing OK.

(Fig. 8-14)

The test transponder selected will now be used to

check whether a signal is being received at this positi-

on. The function will also check whether there is a pre-

programmed position in memory at this orbital position.

(Fig. 8-14)

If this is the case, the message : Orbital position

xx identified.Save satellite?(Fig. 8-15)

To save the satellite position to memory, use the

arrow keys left/right to mark the field Yes, and

confirm by pressing OK.

If the check procedure of the test transponder does

not identify any of the pre-programmed positions

stored in memory, or if the signal received is too weak,

this information will be displayed on screen. (Figs. 8-

16 and 8-17)

To save the satellite position in memory, use the arrow

keys left/right to mark the field Yes and confirm by

pressing OK.

(Fig. 8-15)

(Fig. 8-16)

(Fig. 8-17)

8.4 List of current satellites

The satellite positions saved will be found in the satellite list.

Positions not yet saved will be indicated by “*” .

To rotate the dish antenna to one of the positions on

the list, use the arrow keys to mark the item Current

satellite list.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 39

Press OK.

Use the arrow keys up/down to select the desired

position.

Confirm by pressing OK.

The dish will now be rotated to the selected position.

The rotating procedure is indicated by a blinking

display “Rotating” in the menu.

8.4.1 Selecting a satellite position

To rotate the antenna to the position indicated in the satellite

list, your receiver is equipped with the function Rotate to

sat..

Press the yellow function key (Actions) to open the

window listing the available actions.

Use the arrow keys up/down to mark the item

Rotate to sat.

Confirm by pressing OK.

Press the green function key (Rotate to sat.) to rotate

the antenna to the selected position.

8.5 Deleting a satellite position

To delete a satellite position from the satellite list, proceed as

follows:

Use the arrow keys to mark the item Current

satellite list.

Press OK to display the current satellite list.

Use the arrow keys up/down to select the satellite

you wish to delete.

Confirm by pressing OK.

Use the arrow keys to mark the item Delete sat..

To delete the selected satellite, press OK, a

confirmatory message will be displayed, then press

OK again.

8.6 Reference position

When installing the external installation, the motor must be

parked in the reference position (0°). For this purpose you

can use the function “Go to reference position” at any time

to rotate to this position (0°).

Press the red function key (Ref.pos) to rotate the

antenna automatically to the reference position.

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 40

9 Technical Terms

Antenna cable:

Connecting cable from the modulator of the satellite receiver

to the antenna input socket of the television set; used as an

alternative where no SCART socket is available

Coaxial cable:

Connecting cable between LNB and satellite receiver, used to

transmit the signal received, as well as to supply the LNB with

power

Data compression/MPEG1/MPEG2:

To transmit the current television standard (625 lines repeated

50 times per second) results in a digital data volume of 216

MBit/s. This would require bandwidths that cannot be

provided by either terrestrial or satellite sources. The volume

of data is thus compressed by electronic means to reduce the

volume. In Europe, the MPEG-2 standard has been laid down

as the international standard for data compression. MPEG2 is

a further development of MPEG1

Deemphasis:

Adaptation of the audio frequency profile to the broadcast

signa, this is defined by the broadcast parameters of the

satellite

DiSEqC:

Digital Satellite Equipment Control: a digital switching system

used to control DiSEqC-compatible components of the

extenbal installation via the antenna cable.

DVB:

Digital Video Broadcasting: a universal digital broadcast

standard used for all possible types of data, such as pictures,

graphics, sound and text, in an appropriate form providing

appropriate quality

External unit:

Description used for the complete system mounted outdoors,

consisting of parabolic dish antenna, as well as one or more

LNBs, used to receive signals from one or more satellites

Frequency:

Physical measurement, indicated the number of wave-cycles

per second, expressed as Hertz (Hz)

Frequency range:

a) Satellite resp. LNB:

11 GHz range from 10,70 GHz to 11,70 GHz, 12 GHz range

from 11,70 GHz to 12,75 GHz

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 41

b) Receiver: Intermediate frequency or 1.IF 950 to 2150 MHz

Unit

1 Hz

Description

1 Hertz

Cycles per second

1 kHz

1 MHz

1 GHz

1 Kilohertz

1 Megahertz

1 Gigahertz

1.000

1.000.000

1.000.000.000

LNB/LNC (Low Noise block converter):

The receiving unit at the focal point of the parabolic dish

antenna. Converts the satellite frequency range to that of the

intermediate frequency of the receiver

LOF:

Local oscillator frequency, stated in MHz or GHz, differs

depending on the LNB and frequency range received.

Receiving frequency of the receiver = broadcast frequency of

the satellite - LOF

Modulation at 22 KHz

Next to the 14/28 Volt switching facility, this serves to switch

between 2 LNBs. When used with a Universal LNB it serves

to switch to the high band

Modulator

Switching facility in the satellite receiver or video recorded,

used to connect to the television set using antenna cable

Mode:

determines whether a mono or a stereo programme will be

received

Multyfeed:

External installation consisting of a single parabolic dish and

several LNBs, used to receive signals from several satellites

Parabolic dish:

Dish antenna with parabolic shape, made of metal or coated

synthetics, serves to focus the electromagnetic waves

received from the satellite in a focal point

Polarisation plane:

In order to better utilise the available frequency range,

satellites will broadcast neighbouring frequencies using

opposite polarisation (horizontal and vertical, or dextrorotatory

and laevorotatory). To receive both polarisation planes you

will require two single LNBs or a single V/H LNB.

Satellite:

Designation of a satellite, usually coupled with its orbital

position,

ASTRA

EUTELSAT

19° East

13° East

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 42

Satellite receiver:

The signals received and converted by the LNB cannot be

interpreted by the television set. The satellite receiver further

converts these signals in such a way that it feeds audio and

video signals (AV) to its output connections in a form that can

be used by the television set.

SCART:

Connector plug used for television sets, video recorders,

satellite receivers and other appliances in the field of

entertainment electronics to transmit Audio and visual signals

(AV).

Software update:

Digital television is a new medium. Apart from the improved

picture and sound quality, it also provides the facility for

interactive services. These services are constantly being

developed and improved by providers. To utilise these

services, it may become necessary from time to time to

update the operating software of the receiver.

Transponder:

This processes one or several programmes within the

satellite. That is, reception of data from the ground station,

amplification and broadcast of the signal back to earth.

Universal-LNB:

Term used to describe a triple-band LNB. Used to receive the

ranges FFS (10,70 - 11,70 GHz), BBS (11,70 - 12,50 GHz)

and FFS High Band (12,50 - 12,75 GHz). The entire range is

divided into two bands:

Low Band: 10,70 - 11,80 GHz; LOF 9750 MHz

High Band 11,70 - 12,75 GHz ; LOF 10600 MHz

Supply voltage:

LNBs receive their power supply via the coaxial cable. To this

end the receiver delivers a supply of 14 or 18 Volts

Intermediate frequency:

The frequency range broadcast by satellites cannot be

transmitted via a cable. The LNB therefore converts the

incoming signal to a signal in the intermediate frequency

range of 950 to 2050 MHz. This signal can be transmitted via

cable, and can be interpreted by the receiver.

1. IF = Intermediate frequency

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 43

10 Technical data

DBS-Tuner:

Input frequency range

Input level range -

DBS tuner input

Input/output impedance

Output for 1.IF

AFC capture range

Demodulation

950 .... 2150 MHz

60 dBm ... - 25 dBm

F -connector

75 Ohm

950 ... 2150 MHz (loop through)

+/- 3 MHz

Shaped QPSK

Symbol rate

FEC

Viterbi rates

1 ... 45 Mbaud/s, MCPC

Viterbi and Reed-Solomon

1/2, 2/3, 3/4, 5/6, 7/8, automatic

adaptation

Roll-off Factor

35 %

Demultiplexing:

in accordance w. ISO 13818-1

Video decoding:

Video compression

MPEG-2 and MPEG-1

compatible

Up to MP@ML (main profile @

main level)

Video standard

PAL / 25 Hz

Active image size

Picture format

720 pixels x 576 lines

4 : 3 / 16 : 9

Picture material 16:9

Automatic adjustment for 16:9 TV

sets (via SCART)

Letterbox filtering for 4:3 TV sets

Audio decoding:

Audio compression

MPEG-1 & MPEG-2 Layer I and

Audio mode

Sampling frequencies

Dual (main/sub), Stereo

32 kHz, 44.1 kHz, 48 kHz,

Audio parameters:

Input analogue:

Input levels L/R

Input impedance

0,5 V r.m.s. (nominal)

> 40 kOhm

Output analogue:

Output levels L/R

Output impedance

THD

0,5 V r.m.s. (nominal)

600 Ohm

> 60 dB (1 kHz)

< - 65 dB

Cross-talk

Iniotial volume

stores last value selected

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 44

Video parameters:

Input:

Input level

FBAS 1 Vs-s +/- 0,3 dB into 75

Ohms

Input level RED

Input level GREEN

Input level BLUE

0,7 Vs-s +/- 0,1Vs-s into 75 Ohms

Teletext

Teletext filtering

corresponding to ETS 300 472

standard

Display teletext data

(FBAS) corresponding to ITU-R

BT.653-2 lines: 6-22 and 320-335

TV-SCART:

Output:

switchable FBAS or RGB

VCR-SCART:

Input:

Output:

FBAS or RGB

FBAS

Serial interface RS 232:

Type

RS 232, bi-directional

Bit rate

Connectior

Function

115 kBit/s

D-SUB-socket, 9 pin

Update f.operating software

LNB power supply:

LNB power

400 mA max.; double-

insulated

LNB voltage vertical

LNB voltage horiz.

<14,0V no load, > 11,5 V at 400

< 20V no load, > 17,2 V

at 400 mA

LNB switched off in stand-by mode

22 kHz, Amplitude 0.6 V +/- 0.2 V

22 kHz modulation:

Programme memory:

999 TV programmes

999 RADIO programmes

DiSEqC Control:

DiSEqC 1.0 and DiSEqC 1.2

EPG data:

EPG preview

Timer:

32 events one year ahaead

OSD languages:

German, English

Remote control system

RC-5

Subsystem adress

Modulation frequency

Infrared wavelengthe

10 (SAT 2)

36 kHz

950 nm

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 45

Power supply:

Mains power adapter:

Power requirement:

< 22 W

(in operation, horizontal

polarisation/ 400 mA LNB power)

(in operation, excl. LNB)

(Stand-by Mode)

< 12 W

< 10 W

Mains voltage:

180 V.... 250 V / 47...63 Hz AC

General:

Ambient temperature

Humidity

+15°C...+35°C

< 80%

Dimensions (WxDxH):

Weight:

305 mm x 135 mm x 65 mm

0,8 kg

11 Trouble-shooting guide

Dear customer,

we would like to point out once again that, if you experience

the following problem, you should first follow our suggested

solution before contacting the repair service.

The unit does not function properly (controls do

not respond, image frozen ...)

Disconnect the mains power supply for approx. 5

seconds, then connect it again.

Then switch the receiver on again.

If the problem persists, you should then contact your repair

service.

Your appliance carries the CE mark, and complies with all relevant EU

standards.

Subject to alteration without notice. Not responsible for printing errors. Correct

at 10/02

Copying and reproduction only with specific permission of the publisher.

TechniSat and DIGITY CI are registerd trade marks of

TechniSat Digital GmbH

P.O. Box 560

D-54541 Daun

Germany

www. technisat.de

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 46

Problem

Possible cause

Solution

Various programmes not shown Incorrect programme list

Select different programme list

(see Point 6.2.3.1)

in programme list

selected

Sound OK, screen blue

Unit is in Radio mode

Switch to TV mode

Programmes such as Pro 7,

Sat 1, TM3, Kabel 1, DSF and telephones (DECT standard)

HOT temporarily faulty

Interference by wireless

Increase distance between

receiver and phone station

Controls cannot be operated

Remote control not working

Data stream defective -->unit

blocked

Pull mains plug for approx. 5

seconds, then switch unit on

again

Batteries are spent

Fit new batteries

Intermittent square blocks on

screen. Temporary frozen

picture, no sound, screen

sometimes black with message

“no signal”.

Heavy rain or snow

Remove snow from antenna

Adjust antenna position

Antenna position incorrect

Antenna dish may be too small Adjust antenna position

An obstacle between the dish

and the satellite (e.g. a tree)

Mount antenna in position with

clear view

No picture, no sound, LED on

Short circuit in LNB connection Switch unit off, eliminate short

circuit, switch unit on again

Cable connection defective or

not present

Check all cable connections

Replace LNB

LNB defective

Incorrect external unit selected Correct setting (see Point 5.4)

on receiver

Antenna adjustment incorrect

Adjust antenna position

No picture, no sound, LED not No mains power

Check mains cable and plugs

No reception of programmes

that were in order previously

Antenne verstellt oder defekt

Check antenna

Programme has moved to a

different transponder

Perform search procedure (see

Point 7.4)

Programme no longer being

broadcast

None

Antenna cannot be rotated

Motor not compatible with

DiSEqC 1.2

Use suitable motor

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 47

12 Annexure

Co-ordinates of selected German cities (1)

City

Geogr. Longitude (E)

6,1

Geogr. Latitude (N)

50,8

Aachen

Aalen

Augsburg

Aschaffenburg

Bad Neuenahr-Ahrweiler 7,1

Bad Reichenhall

Baden Baden

Bamberg

Berlin

Beucha

Bielefeld

Bonn

Brandenburg

Braunschweig

Bremen

Bremerhaven

Celle

Chemnitz

Cottbus

Darmstadt

Daun

10,1

10,9

9,2

48,8

48,4

50,0

50,6

47,7

48,8

49,9

52,5

51,3

52,0

50,7

52,4

52,3

53,1

53,6

52,6

50,8

51,8

49,9

50,2

51,0

48,7

51,5

51,1

51,4

51,2

51,0

53,8

53,4

51,0

51,5

54,8

50,1

52,3

48,0

48,4

50,6

52,1

49,5

12,9

8,2

10,9

13,4

12,7

8,5

7,1

12,6

10,5

8,8

8,6

10,1

12,9

14,3

8,7

6,8

Dippach

10,1

10,8

7,5

13,7

6,8

10,3

9,7

7,2

11,0

7,0

9,4

8,7

14,5

7,9

11,8

9,7

14,7

11,0

Donauwörth

Dortmund

Dresden

Duisburg

Düsseldorf

Eisenach

Elmshorn

Emden

Erfurt

Essen

Flensburg

Frankfurt/M.

Frankfurt/O.

Freiburg/Br.

Freising

Fulda

Fürstenberg

Fürth

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 48

Co-ordinates of selected German cities (2)

City

Geogr. Longitude (E)

11,1

12,1

15,0

9,9

11,0

12,0

9,4

10,0

7,8

9,7

9,1

8,7

9,2

10,0

11,9

11,4

7,7

7,8

8,4

Geogr. Latitude (N)

47,5

Garmisch-Partenkirchen

Gera

50,9

51,2

51,5

51,9

51,5

52,1

53,6

51,7

52,4

54,2

49,4

49,2

52,2

50,3

48,8

51,4

49,5

49,0

51,3

47,7

54,3

50,4

47,7

51,0

51,3

49,2

48,5

51,3

49,5

53,9

53,3

52,1

50,0

49,5

52,3

51,2

49,3

48,1

49,9

Görlitz

Göttingen

Halberstadt

Halle/Saale

Hameln

Hamburg

Hamm

Hannover

Heide

Heidelberg

Heilbronn

Hildesheim

Hof

Ingolstadt

Iserlohn

Kaiserslautern

Karlsruhe

Kassel

Kempten/Allgäu

Kiel

9,5

10,3

10,1

7,6

9,2

7,0

Koblenz

Konstanz

Köln

Krefeld

6,6

8,1

Landau/Pfalz

Landshut

Leipzig

Ludwigshafen

Lübeck

Lüneburg

Magdeburg

Mainz

12,2

12,4

8,4

10,7

10,4

11,6

8,3

8,5

8,9

6,4

8,7

Mannheim

Minden

Mönchengladbach

Mühlhausen

München

Münster

11,6

8,9

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 49

Co-ordinates of selected German cities (3)

City

Geogr. Longitude(E)

13,3

10,0

11,8

10,8

11,1

6,9

8,0

10,9

8,2

Geogr. Latitude (N)

53,6

Neubrandenburg

Neumünster

Nienburg

54,1

51,8

51,5

49,5

51,5

48,5

54,3

53,2

52,3

51,7

48,6

50,5

52,4

47,8

49,0

48,5

54,1

49,2

52,1

52,9

50,1

53,6

50,9

51,2

49,3

48,0

48,8

49,8

48,5

48,4

51,0

50,1

53,5

53,9

52,4

51,3

49,8

49,3

50,7

Nordhausen

Nürnberg

Oberhausen

Offenburg

Oldenburg/Holsn.

Oldenburg

Osnabrück

Paderborn

Passau

8,1

8,8

13,5

12,1

13,1

9,6

12,1

9,2

Plauen

Potsdam

Ravensburg

Regensburg

Reutlingen

Rostock

Saarbrücken

Salzgitter

Salzwedel

Schweinfurt

Schwerin

Siegen

12,1

7,0

10,4

11,2

10,2

11,4

8,0

7,1

8,4

11,3

9,2

6,7

Solingen

Speyer

Starnberg

Stuttgart

Trier

Tübingen

Ulm

Weimar

9,1

10,0

11,3

8,2

Wiesbaden

Wilhelmshaven

Wismar

Wolfsburg

Wuppertal

Würzburg

Zweibrücken

Zwickau

8,1

11,5

10,8

7,2

9,9

7,4

12,5

Download from Www.Somanuals.com. All Manuals Search And Download.

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 50

For everyday use

Switching on and off

Switch the unit on by pressing the On/Stand-by key,

either on the receiver or on the remote control unit.

Pressing the same key again, either on the receiver or

on the remote control unit, will switch the receiver off

again.

The receiver is now in Stand-by mode.

Programme selection

Using the programme keys up/down

Use the programme keys up/down to switch from

one programme to another, one slot at a time. You can

use the keys either on the receiver panel or those on

the remote control unit.

Using the numeric keys

Enter the desired programme number using the

numeric keys. For example:

for programme slot 1

then 4

for programme slot 14

then 3,

then 4

for programme slot 234

When entering programme numbers with more than one

digit, you have approximately 3 seconds after pressing each

key to complete the entry.

If you wish to enter a number consisting of only one or two

digits, you can speed up the selection process by keeping the

key depressed a little longer on the last digit.

Volume control

To control the volume of your receiver, use the keys

Volume + to increase the volume and Volume - to

decrease the sound volume.

Press the key Sound on/off to switch the sound off

(mute), press the key again to switch sound on again.

TV/radio switching

The pre-programming of your receiver includes radio as well

as television programmes You can thus also enjoy your

favourite radio programmes in digital quality, by switching to

Radio mode. In this case the corresponding TV image is not

displayed, you will see a blank screen with the programme

name displayed.

Use the TV/Radio key to switch the receiver to radio

mode.

The receiver will now switch to the radio programme

last selected.

Press the TV/Radio key again to switch to the

television programme last selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tascam Car Stereo System DA 98HR User Manual
Timex Pill Reminder Device W254 509 095002 02 User Manual
Toastess Coffeemaker TFC 326 User Manual
Toastmaster Oven TOV211 User Manual
Tote Vision Computer Monitor LCD 1411TC User Manual
Trane Air Conditioner XE1000 User Manual
Transcend Information Camera Accessories 2GSDM80 User Manual
Velodyne Acoustics Speaker VDR 10 User Manual
ViewSonic MP3 Player VS13482 User Manual
VocoPro Music Mixer DA 8900 User Manual