Team Products Drill PMD8127 User Manual

TEAM PRODUCTS INTERNATIONAL INC. Limited Warranty  
WhAT IS COvERED: Any defect in materials and workmanship.  
FOR hOW LONg: 2 years from date of purchase.  
WhAT WE WILL DO: If your product is defective and returned within 30 days  
after the date it was purchased, we will replace it at no charge to you. If  
returned after 30 days but within 2 years of the date of purchase we will  
repair it or, at our option, replace it at no charge to you.  
If we repair your product, we may use new or reconditioned replacement  
parts. If we choose to replace your product, we may replace it with a  
new or reconditioned one of the same or similar design. The repair or  
replacement will be warranted under our standard 2 year warranty.  
LIMITATIONS: IMPLIED WARRANTIES, INCLUDINg ThOSE OF FITNESS FOR A  
PARTICULAR PURPOSE AND MERChANTAbILITy (AN UNWRITTEN WARRANTy  
ThAT ThE PRODUCT IS FIT FOR ORDINARy USE), ARE LIMITED TO 2 yEARS  
FROM DATE OF PURChASE. WE WILL NOT PAy FOR LOSS OF TIME, INCONvE-  
NIENCE, LOSS OF USE OF yOUR PRODUCT OR PROPERTy DAMAgE CAUSED  
by yOUR PRODUCT OR ITS FAILURE TO WORk, OR ANy OThER INCIDENTAL  
OR CONSEqUENTIAL DAMAgES INCLUDINg PERSONAL INjURy.  
Some states do not allow limitations on how long an implied warranty  
lasts or the exclusion or limitation of incidental or consequential damages,  
so the above exclusions or limitations may not apply to you.  
12V, 14.4V, 18V  
Cordless Drills  
WhAT WE ASk yOU TO DO: To get warranty service for your product,  
you must provide proof of the date of purchase. Within 30 days of the  
date it was purchased, return your product to your place of purchase for  
immediate replacement. After 30 days, but before the end of the 2 year  
warranty period, you may return the product to the following address:  
Team Products International  
Attn: Customer Service Returns  
Owner’s Manual  
35 A Continental Drive  
Wayne, Nj 07470  
We suggest that you retain your original packing material in the event  
you need to ship your product. When sending your product include your  
name, address, phone number, proof of date of purchase, and a  
description of the operating problem. After repairing or replacing your  
product, we will ship it to your home or office within four weeks.  
WhAT ThIS WARRANTy DOES NOT COvER: Among oTher ThIngS ThIS  
WArrAnTy doeS noT cover defecTS reSulTIng from AccIdenTS,  
dAmAge WhIle In TrAnSIT To our ServIce locATIon, AlTerATIonS,  
unAuThorIzed repAIr, fAIlure To folloW InSTrucTIonS, mISuSe, fIre,  
flood, And AcTS of god. If your producT IS noT covered by our  
WArrAnTy, cAll our cuSTomer ServIce number AT (888) 231-4022 To  
deTermIne WheTher We WIll repAIr your producT And oTher repAIr  
InformATIon, IncludIng chArgeS. We, AT our opTIon, mAy replAce  
rATher ThAn repAIr your producT WITh A neW or recondITIoned  
one of The SAme or SImIlAr deSIgn. The repAIr or replAcemenT WIll  
be WArrAnTed for 2 yeArS.  
Models: PMD8127  
PMD8128  
PMD8129  
PMD8131  
PMD8133  
ThIS lImITed WArrAnTy IS The only one We gIve on your producT,  
And IT SeTS forTh All our reSponSIbIlITIeS regArdIng your producT.  
There Are no WArrAnTIeS WhIch exTend beyond The deScrIpTIon SeT  
forTh Above.  
©2006The Coleman Company, Inc. All rights reserved.  
STATE LAW RIghTS: This warranty gives you specific legal rights and you  
may also have other rights which may vary from state to state.  
COLEMAN® and  
are registered trademarks ofThe Coleman Company, Inc., used under license.  
Designed in the USA and custom-manufactured in China forTeam Products International Inc.  
Distributed byTeam Products International Inc., Mountain Lakes, NJ 07046.  
PMD121505-205  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12V, 14.4V, 18V  
Cordless Drills  
Owner’s Manual  
5.To reduce the risk of damaging the battery charger power cord, be sure to pull  
the plug rather then the cord when disconnecting it from the power supply.  
Always position the cord so it will not be stepped on or tripped over.This will  
prevent damage to the cord.  
Controls and Components:  
Batteries and AC Charger  
1. Battery with Release Buttons On Each Side (PMD8133 includes 2 batteries)  
2. 120V AC Adaptor  
3. Charging Stand with LED Charging Indicators  
6. An extension cord should not be used unless absolutely necessary. Use of an  
improper extension cord can result in risk of fire or electric shock. If using an  
extension cord make sure that:  
A)The pins on the plug of the extension cord are the same number,  
size and shape as those on the plug on the charger.  
1
7
6
5
B)The extension cord is properly wired and in good working  
condition.  
4
C)The wire size is the same or larger than the ones specified below:  
10  
Recommended size of Extension Cord for Battery Charger  
8
Length of Cord (Feet)  
AWG Size of Cord*  
25  
18  
50  
18  
100  
16  
150  
14  
9
2
*The smaller the AWG (American Wire Gauge) number of the extension cord,  
the higher the capacity of the cable for conducting current to ensure proper  
usage of the tool.  
11  
3
7. Do not operate charger with a damaged cord or plug.  
8. Do not operate the charger if it has received a sharp blow, been dropped or  
damaged in any other way.  
12  
13  
9. Do not open the drill, battery or battery charger.There are no user serviceable  
parts. Opening the unit will void the warranty.  
14  
10. Unplug the charger from its power source when not in use.  
Drill:  
11. Do not touch the terminals inside the battery charger with any other metal  
object such as nails or coins.This can short the charger.  
4. 3/8” Jacobs Keyless Chuck  
5. 24 AdjustableTorque Settings Control Ring  
6. Forward/Lock/Reverse Switch  
12. Do not store the unit in areas where the temperature can exceed 120°F.  
7. High/Low Speed Switch (PMD8131 and PMD8133 only)  
8. Variable SpeedTrigger Switch  
13. Do not throw the battery or battery charger in fire.This can cause an  
explosion.  
9. Accessory/Bit Holder  
14. During extreme conditions, the battery may leak. This does not indicate a  
battery failure. However, if the liquid gets on your skin, immediately wash  
with soap and water, neutralize the area with a mild acid such as lemon juice  
or vinegar. If the liquid gets into your eyes, flush them with clean water  
immediately for a minimum of 10 minutes and seek medical attention.  
10. Comfort Rubber Grip (PMD8131 and PMD8133 only)  
Accessories:  
11. 6 Various Screwdriver Bits  
12. 2” Extension Bar  
13. 2 Double Ended Screwdriver Bits  
14. 6 Various Drill Bits  
(Each Drill comes with a storage case.)  
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
12V, 14.4V, 18V  
Cordless Drills  
Owner’s Manual  
INSTRUCTIONS FOR USE:  
ChargingThe Battery  
NOTE: While the battery is placed in the charger, the RED LED indicator light  
will remain on. If charging more than one battery, wait at least 15 minutes  
between each charge. Use only the battery charger that is supplied with this  
tool. Using another charger may cause damage to the battery.  
THE BATTERY(IES) MAY NOT BE FULLY CHARGED FROMTHE  
FACTORY. READ ALL INSTRUCTIONSTHOROUGHLY PRIORTO FIRST  
USE.  
WARNING: Never charge a battery pack again immediately after it has been  
fully charged.This can give rise to the battery pack being overcharged and a  
reduced battery life. DO NOT leave the battery pack in the charger for more than  
8 hours.  
The Drills covered by this manual use the same battery and battery charger.  
Your Drill comes complete with a rechargeable battery which we recommend  
that you fully charge before the first use.  
Drill must be charged for 8 hours prior to first use. After initial charge, allow  
approximately 3 to 8 hours to recharge your battery.  
UsingThe Drill  
CAUTION: Always make sure that the tool is switched  
OFF and the battery pack is removed from the drill  
before changing any bits.  
The battery should be recharged when the drill does not operate up to its  
normal performance level. Do not continue to operate the drill in this depleted  
capacity. Recharge the battery immediately.  
Loosen the keyless chuck by holding the ring and  
turning the sleeve counter clockwise. Select the drill  
bit or screwdriver you want to use and place it in  
the keyless chuck.Twist the sleeve of the keyless  
chuck clockwise to tighten it, making sure the drill bit  
remains in the center of the keyless chucks teeth.  
To increase the life of your battery, do not leave the battery charging for more  
than 8 hours. While this is not a safety concern, overcharging may reduce the  
life of the battery.  
Overtime, if drill is not used, the battery will lose capacity. For maximum  
performance, recharge the battery after prolonged storage or non-use periods.  
Twist the 24 setting torque control ring to the desired  
setting. Lower settings are better for light work such  
as driving screws into soft materials. Higher settings are  
recommended for drilling into harder surfaces.  
NOTE: Before inserting or removing the battery from the charging base, always  
ensure that the base is not plugged into a 120V power source.  
When properly adjusted, the clutch will slip at its present  
torque setting to prevent driving the screw too deep or  
to prevent damage to the tool.  
1.To begin charging, remove the battery pack from the tool by pressing on the  
battery release buttons on either side of the battery pack and pulling down.  
To operate the drill in forward setting, simply keep the  
Forward/Lock/Reverse switch flat against the  
side of the drill as shown.To change to reverse  
setting, move the Forward/Lock/Reverse switch  
until it is flat against the opposite side of the  
drill. Keeping the Forward/Lock/Reverse switch  
in the center position locks the drill and prevents  
unintentional use. It is recommended that the  
Drill is in the locked position when it is not in use  
or is being stored.  
2. Plug the battery pack into the battery charger making sure the positive (+) and  
negative (-) poles of the battery match the positive (+) and negative (-) poles  
of the battery charger.  
NOTE: The battery will only fit into the battery charger and the tool one way.  
3. Plug one end of the 120 Volt AC Adaptor into the battery charger and the  
other end into any standard 120 Volt wall outlet.The RED LED indicator on the  
battery charger will illuminate to indicate that the battery is charging.  
CAUTION: Always check the direction of the rotation before using the drill.  
4. Full charging will take between 3 to 8 hours.  
The speed of the drill is increased by the amount of pressure you place on the  
ON/OFF trigger switch.The less pressure you put on the trigger switch, the  
slower the drill will go.  
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
12V, 14.4V, 18V  
Cordless Drills  
Owner’s Manual  
TROUBLESHOOTINGTIPS:  
DRILL DOES NOT WORK?  
• Recharge the battery  
Your drill comes with an automatic braking function that quickly stops the chuck  
from turning when the trigger switch is released.  
Your drill (models PMD8131 and PMD8133) has two speed ranges; low speed  
(position 1) (0-400 rpm) and high speed (position 2 ) (0-1100 rpm).  
CHARGING INDICATOR LED NOT ILLUMINATED DURING  
RECHARGING?  
Screwdriver Operation  
• Check that battery pack is properly connected to the battery charger  
• Check that the AC Adaptor is properly connected at both ends  
Place the point of the screwdriver bit into the head of the screw and apply slight  
pressure to the tool. Press the trigger switch slightly and then gradually increase  
the drill speed. Release the trigger switch as soon as the clutch engages.  
Note: Starting the drill at too high of a speed can  
damage the drill bit or reduce the life of the bit.  
SPECIFICATIONS for PMD8127  
Voltage  
12V  
Make sure that the driver bit is inserted straight in  
the screw head or the screw may become damaged  
or will not be inserted properly. When driving wood  
screws, pre-drill pilot holes into the surface to make  
driving easier.This will also prevent the wood from  
splitting.  
Speed 1  
0-600RPM  
24 + Drill  
Torque Settings  
Chuck Capacity  
Charger Input  
ChargingTime  
BatteryType  
up to 3/8”  
120V AC 60Hz  
Approx. 3 –8 Hours  
Ni-Cad  
Note: When drilling, the drill bit can become stuck.  
If this happens, a very high torque will be produced.  
Always take care to hold the drill firmly to prevent  
possible damage or injury.  
SPECIFICATIONS for PMD8128  
Maintenance  
Voltage  
14.4V  
Clean the Drill regularly. Before cleaning, remove the battery pack and any  
accessories (bits etc.).To clean, use ONLY a mild soap and damp cloth on the  
housing. Never immerse drill in any kind of fluid. Do not use any solvents or  
harsh abrasives on the drill housing as this may cause damage to the unit.  
Always keep the ventilation openings clear.  
Speed 1  
0-600RPM  
24 + Drill  
Torque Settings  
Chuck Capacity  
Charger Input  
ChargingTime  
BatteryType  
up to 3/8”  
120V AC 60Hz  
Approx. 3 –8 Hours  
Ni-Cad  
NOTE: All bearings in these tools are lubricated with a sufficient amount of  
high-grade lubricant for the life of the unit under normal operating conditions.  
No further lubrications required.  
CAUTION: DO NOT keep the trigger switch pressed in with tape or any other  
permanent means or the circuit will not function properly. A malfunction may  
result, possibly causing overheating or damage to the unit.  
Do not open the drill, battery or battery charger.There are no user serviceable  
parts. Opening the unit will void the warranty.  
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
12V, 14.4V, 18V  
Cordless Drills  
Owner’s Manual  
SPECIFICATIONS for PMD8129  
Voltage  
18V  
Speed 1  
0-600RPM  
24 + Drill  
Torque Settings  
Chuck Capacity  
Charger Input  
ChargingTime  
BatteryType  
up to 3/8”  
120V AC 60Hz  
Approx. 3 –8 Hours  
Ni-Cad  
SPECIFICATIONS for PMD8131 and PMD8133  
Voltage  
18V  
Speed 1  
0-400RPM  
0-1100RPM  
24 + Drill  
Speed 2  
Torque Settings  
Chuck Capacity  
Charger Input  
ChargingTime  
BatteryType  
up to 3/8”  
120V AC 60Hz  
Approx. 3 –8 Hours  
Ni-Cad  
Questions?  
If you have any questions about this product, please contact our Customer  
Service Department at (888) 231-4022, 9 AM to 5 PM EST, Monday through  
9
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Tatung Flat Panel Television V26FMFJ User Manual
TOA Electronics Digital Camera C CV14 2 NTSC User Manual
Toastmaster Coffeemaker TCM10PWF User Manual
Toshiba Camcorder HDD2136 User Manual
Toshiba CRT Television 32A62 User Manual
Toshiba DVD Player SD7200 User Manual
Toshiba Laptop X800 User Manual
Ultratec Projection Television 50DX20B User Manual
Uniden Scanner UBC RH96 User Manual
Wagner SprayTech Paint Sprayer 279029 User Manual