Teac CD Player E24E User Manual
PortaCD-RW Drive  
User’s Manual  
CDWE24E  
USB 4X4X6  
PCMCIA 4X4X24  
®
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC Radio Frequency Interference Regulations  
Warning: This equipment generates, uses, and can radiate radio frequency energy and if  
not installed and used in accordance with the instructions contained in this manual, may  
cause harmful interference to radio and television communications. This equipment has  
been tested and found to comply with the limits for a Class B digital device pursuant to  
Subpart J of Part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation. However, there is no  
guarantee that interference will not occur in a particular installation. To ensure compliance  
with FCC rules, the cable that connects the unit to the computer must be a shielded interface  
cable.  
Note: Connecting this device to peripheral devices that do not comply with Class B  
requirements or using an unshielded peripheral cable could result in interference to radio  
or television reception. To ensure that the use of this product does not contribute to  
interference, use a shielded interface cable.  
If this equipment does cause harmful interference to radio or television reception (which  
can be determined by turning the equipment off and on), the user may try to correct the  
interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna  
• Move the device and the receiver further apart  
• Connect the equipment to an electrical outlet on a circuit different from that of the receiver  
• Consult the dealer or an experienced audio television technician  
Also, the following booklet may prove helpful: How to Identify and Resolve Radio-TV  
Interference Problems. It is available from the U.S. Government Printing Office,  
Washington, D.C. 20402, stock number 004-000-00345-4.  
The user is cautioned that any changes or modifications to this equipment not expressly  
approved by TEAC America, Inc. could void the user’s warranty.  
Copyright and Trademark Information  
© Copyright 2001 TEAC America, Inc. All rights reserved.  
TEAC America, Inc. reserves the right to modify product offerings or  
specifications without advanced notice. No part of this publication may be  
reproduced in any format without the expressed written permission of TEAC  
America, Inc.  
• TEAC is a trademark of TEAC Corporation.  
• IBM PC is a registered trademark of International Business Machines  
Corporation.  
• Windows, Windows 98SE, Windows Me, Windows 2000 Professional, and  
Windows NT are trademarks or registered trademarks of Microsoft  
Corporation.  
• iBook, iMac, PowerBook, Power Macintosh G3 and G4 are trademarks or  
registered trademarks of Apple Computer, Inc.  
• Adobe and Acrobat are trademarks of Adobe Systems, Inc.  
• Roxio, Easy CD Creator, DirectCD, and Adaptec are registered trademarks of  
Adaptec, Inc.  
All other trademarks and registered trademarks are the property of their  
respective owners.  
TEAC PortaCD-RW User’s Manual  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Registration Information  
There is no need to register any portion of this kit. TEAC provides 100% support  
for the drive and the recording software. Refer to “Technical Support” on  
page 64 if you wish to contact TEAC.  
Product Warranty Information  
The TEAC PortaCD-RW Drive features a one year warranty from the date of  
purchase. Please keep your receipt as proof of purchase.  
About This Manual  
This manual, the TEAC PortaCD-RW Drive User’s Manual, explains how to  
install and operate the TEAC PortaCD-RW drive. This manual is divided into the  
following chapters:  
Chapter 1. Introduction: This chapter introduces the PCMCIA and USB  
versions of the PortaCD-RW drive and describes shipping package contents and  
recommended system requirements.  
Chapter 2. Connecting the USB PortaCD-RW Drive to a Windows System:  
This chapter explains how to connect the USB version of the PortaCD-RW drive to  
an IBM PC compatible computer running Windows.  
Chapter 3. Connecting the PCMCIA PortaCD-RW Drive to a Windows  
System: This chapter explains how to connect the PCMCIA version of the PortaCD-  
RW drive to an IBM PC compatible computer running Windows.  
Chapter 4. Installing and Using Easy CD Creator 5 on a Windows Systems:  
This chapter explains how to install Easy CD Creator and DirectCD, which are  
included on the installation disc for Windows systems.  
Chapter 5. Connecting the USB PortaCD-RW to and Installing Software on  
Macintosh Systems: This chapter explains how to connect the PortaCD-RW to  
Apple Power Macintosh systems that feature a USB port. It also explains how to  
install the Toast pre-mastering software included on the Toast software CD-  
ROM disc for Macintosh systems.  
Chapter 6. Connecting to Audio Equipment. This chapter explains how to  
connect the PortaCD-RW to audio equipment.  
Chapter 7. Handling, Loading, and Ejecting Discs. This chapter contains  
information on handling, loading and ejecting discs and on recommended media  
and disc formats.  
Specifications: This section provides technical specifications for the PortaCD-  
RW drive.  
Technical Support: This section provides technical support information.  
ii  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Safety Precautions  
TEAC CD Rewritable (CD-RW) Drives are high-precision electronic devices.  
Do not use them in any manner other than as specified in this manual. Please read  
this manual in its entirety before you begin the installation procedure. Use of  
controls, adjustments, or performance of procedures other than those specified  
herein may result in hazardous radiation exposure.  
To prevent fire or shock, do not expose the unit to moisture or rain.  
To prevent electrical shock, do not attempt to disassemble the PortaCD-RW  
drive. Refer servicing to authorized personnel.  
The TEAC PortaCD-RW uses an invisible laser beam that can damage your  
vision if you stare directly into it or view it with optical instruments when the disc  
tray is extended. Avoid direct visual contact with the laser beam.  
A user who changes or modifies the unit or operating procedures specified herein  
without express written approval by the manufacturer will void user authority to  
operate the equipment.  
Specifications and features subject to change without notice or obligation.  
disc tray extended  
Caution: Use of controls or adjustments or performance of procedures other  
than those specified herein may result in hazardous radiation exposure.  
TEAC PortaCD-RW User’s Manual  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Optical Pickup  
Optical Pickup  
PU-W204  
Type  
Laser output  
Less than 1mW (playback) and 23mW (record) on the  
objective lens  
Wavelength  
777-787nm  
Declaration of Conformity  
Declaration of Conformity  
Model Number:  
Trade Name:  
Responsible Party:  
Address:  
CDWE24E  
TEAC  
TEAC AMERICA, Inc.  
7733 Telegraph Road  
Montebello, California 90640, U.S.A.  
Telephone Number:  
1-323-726-0303  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful interference, and (2) This device must  
accept any interference received, including interference that may cause undesirable opera-  
tion.  
iv  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Table of Contents  
FCC Radio Frequency Interference Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i  
Copyright and Trademark Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i  
Registration Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii  
Product Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii  
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii  
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii  
Optical Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv  
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv  
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii  
Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
PCMCIA Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
USB Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
Both Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
Recommended System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
All systems (both PCMCIA & USB versions): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
For Windows systems (both PCMCIA & USB versions): . . . . . . . . . . . . . . . . . . . . . . . 2  
For Macintosh systems (USB version only): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Unpacking Your PortaCD-RW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
PCMCIA Version Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
USB Version Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Power Sources/Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Power Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Power Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Charging the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Front and Right Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Operating Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Chapter 2. Connecting the USB PortaCD-RW Drive to a Windows System 9  
Connecting the USB PortaCD-RW Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Connecting and Disconnecting the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Windows 98SE Users: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Windows Me/2000 Professional Users: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
All Users: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Installing the Driver Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Installing the Driver Software on Windows 98SE/Me Systems . . . . . . . . . . . . . . . . . . 12  
Drive Letter Allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Installing the Driver Software on Windows 2000 Systems . . . . . . . . . . . . . . . . . . . . . 16  
Installing the Driver Without a Floppy Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Uninstalling the USB Driver Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Chapter 3. Connecting the PCMCIA PortaCD-RW to a Windows System . 23  
Connecting the PCMCIA PortaCD-RW Drive to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Detecting the PCMCIA Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Installing the PCMCIA Card Using the Windows PC Card Wizard . . . . . . . . . . . . . . . . 26  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
v
Installing the PortaCD-RW Driver Using the Windows Wizard . . . . . . . . . . . . . . . . . . . 28  
For Windows 98SE/Me/2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Chapter 4. Installing and Using Easy CD Creator 5 Basic  
on Windows Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Uninstalling Old Versions of Easy CD Creator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Installing Easy CD Creator 5 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Starting Easy CD Creator 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Using Easy CD Creator 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
About the Help Files (help button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
Creating Audio Discs (make a music CD button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
Creating Music CDs (musicCD button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
Creating Data Discs (make a data CD button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
Formatting Blank Discs for Use With DirectCD (directCD button) . . . . . . . . . . . . . . 43  
Creating Archive CDs (dataCD button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
Creating Photo or Video CDs (make a photo or video CD button) . . . . . . . . . . . . . . . 45  
Copying Discs (CD copier button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Upgrading the Software (upgrade button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Updating the Software (web-checkup button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Creating CD Labels (CD label creator button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
Uninstalling Easy CD Creator 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
Chapter 5. Connecting the USB PortaCD-RW to and Installing Software  
on Macintosh Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
Connecting to a Macintosh System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
Before You Disconnect the Cable from the Computer’s USB Port . . . . . . . . . . . . . . . 50  
Installing Toast Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51  
Starting Toast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54  
Chapter 6. Connecting to Audio Equipment . . . . . . . . . . . . . . . . . . . . . . . . 57  
Chapter 7. Handling, Loading, and Ejecting Discs . . . . . . . . . . . . . . . . . . . 59  
Handling Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59  
Loading and Ejecting Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60  
Loading a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60  
Ejecting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
Recommended Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62  
Disc Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63  
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64  
vi  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of Figures  
Figure 1. Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Figure 2. Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Figure 3. Front and Right Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Figure 4. Connecting Cables (USB version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Figure 5. Unplug Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Figure 6. Add New Hardware Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Figure 7. Add New Hardware Wizard: Search for Best Driver . . . . . . . . . . . . . . . . . . . . 12  
Figure 8. Add New Hardware Wizard: Specify Search Location . . . . . . . . . . . . . . . . . . 13  
Figure 9. Add New Hardware Wizard: Device Search . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Figure 10. Add New Hardware Wizard: Software Installation Finished . . . . . . . . . . . . . 14  
Figure 11. System Properties Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Figure 12. Drive Letter Allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Figure 13. Found New Hardware Wizard: Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Figure 14. Found New Hardware Wizard: Install Hardware Device Drivers . . . . . . . . . 16  
Figure 15. Found New Hardware Wizard: Locate Driver Files . . . . . . . . . . . . . . . . . . . . 17  
Figure 16. Found New Hardware Wizard: Driver Search Results . . . . . . . . . . . . . . . . . . 17  
Figure 17. Digital Signature Not Found Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Figure 18. Found New Hardware Wizard: Completing . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Figure 19. Device Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Figure 20. Freecom Driver Remove Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Figure 21. Freecom Driver Remove: Remove Actions Panel . . . . . . . . . . . . . . . . . . . . . 20  
Figure 22. Freecom Driver Remove: Restart Windows . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Figure 23. Connecting Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Figure 24. Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Figure 25. System Properties Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Figure 26. Welcome to PC Card Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Figure 27. PC Card Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Figure 28. Installation Complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Figure 29. System Settings Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Figure 30. Add New Hardware Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Figure 31. Search for the Best Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Figure 32. Select the Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Figure 33. Driver Located . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Figure 34. Installation Complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Figure 35. System Settings Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Figure 36. Close Program Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Figure 37. Auto Detect Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Figure 38. Choose Setup language Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Figure 39. InstallShield Wizard Welcome Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Figure 40. Setup Type Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Figure 41. Ready to Install Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Figure 42. Installing Status Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Figure 43. InstallShield Wizard Completed Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Figure 44. Restart Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Figure 45. Easy CD Creator Select a Project Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
vii  
 
Figure 46. Select a Project Panel: Help Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
Figure 47. Help Topics Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
Figure 48. Select a Project Panel: Make Music CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
Figure 49. Untitled Music CD Project Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
Figure 50. Select a Project Panel: Make a Data CD Button . . . . . . . . . . . . . . . . . . . . . . 43  
Figure 51. DirectCD Format Utility Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
Figure 52. Untitled Data CD Project Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
Figure 53. Select a Project: Make a Photo or Video CD Button . . . . . . . . . . . . . . . . . . . 45  
Figure 54. Select a Project: CD Copier Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
Figure 55. CD Copier Welcome Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
Figure 56. CD Copier Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
Figure 57. Select a Project: Web-checkup Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Figure 58. Select a Project: CD Label Creator Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
Figure 59. Connecting Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
Figure 60. Toast Software Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51  
Figure 61. Toast Main Installation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
Figure 62. Continuation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
Figure 63. Read Me/Registration Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53  
Figure 64. Toast 4.1.2 Installer Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53  
Figure 65. Installing Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54  
Figure 66. Installation Successful Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54  
Figure 67. Toast Folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54  
Figure 68. Toast Main Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
Figure 69. Connecting Analog Audio Speakers or Headphones . . . . . . . . . . . . . . . . . . . 57  
Figure 70. Handling Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59  
Figure 71. Extending the Disc Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60  
Figure 72. Inserting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60  
viii  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PCMCIA Version  
Chapter 1. Introduction  
Thank you for choosing the TEAC PortaCD-RW (model CDWE24E).  
This durable, portable, external PortaCD-RW drive comes in either PCMCIA or  
USB interface versions. Please refer to the appropriate sections of this document  
for information on package contents, performance, power requirements, and  
installation procedures for the version you purchased.  
PCMCIA Version  
The PCMCIA version can write to CD-R and CD-RW discs at 4X speed and read  
CD-ROM discs at a maximum of 24X speed. It is designed for use with IBM PC/  
AT compatible portable computers that utilize PCMCIA card technology.  
USB Version  
The USB version can write to CD-R and CD-RW discs at 4X speed and read CD-  
ROM discs at a maximum of 6X speed. It is designed for use with either:  
  IBM PC/AT compatible portable computers that feature a USB port, or  
  Apple iBook, iMac, PowerBook, Power Macintosh G3 or G4 computers that  
feature a USB port.  
Both Versions  
The slim design of the TEAC PortaCD-RW makes it ideal for portable use. The  
integrated rechargeable battery can provide drive power when the AC adapter is  
disconnected from the drive.  
The PortaCD-RW features a disc tray that extends forward to facilitate the loading  
and unloading of discs.  
The PortaCD-RW package includes both Roxio Easy CD Creator pre-mastering  
software for Windows systems, and Toast pre-mastering software for Macintosh  
systems.  
Please read this manual in its entirety before you begin the installation procedure.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
       
Recommended System Requirements  
Recommended System Requirements  
The following items represent the minimum system requirements for successful  
operation of the PortaCD-RW.  
All systems (both PCMCIA & USB versions):  
  64MB of RAM  
  A hard drive that meets or exceeds the following minimum specifications:  
  1GB hard disk space (or more)  
  1.2MB/second data transfer rate (or faster)  
  12ms average access time (or less)  
  Sufficient hard disk space for software installation (approximately  
70MB)  
  CD-ROM drive (DAE support for CD to CD-RW audio recording)  
For Windows systems (both PCMCIA & USB versions):  
  IBM PC-compatible Pentium 200MHz or higher  
  Windows 98SE, Windows Me, or Windows 2000 Professional (Windows 95  
and NT 4.0 are not supported)  
  PCMCIA Card Type II slot for PCMCIA version, or  
  USB 1.1 port for USB version  
  Floppy disk drive (to install software drivers) or Internet access (to download  
and install software drivers)  
For Macintosh systems (USB version only):  
  233 MHz or higher  
  OS 8.6 or higher  
  USB 1.1 port  
  Apple iMac, iBook, G3, G4 or higher  
2
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Unpacking Your PortaCD-RW  
Unpacking Your PortaCD-RW  
Your TEAC PortaCD-RW and accessories are packaged in a sturdy shipping  
container.  
Check the package contents list for the version of the PortaCD-RW drive you  
purchased. If an item is missing, contact the dealer from whom you purchased the  
drive.  
PCMCIA Version Package Contents  
  PortaCD-RW portable CD-RW drive  
  AC adapter  
  PCMCIA card/cable  
  One blank CD-R disc  
  One blank CD-RW disc  
  Installation software floppy disk  
  TEAC PortaCD-RW User’s Manual (this booklet)  
  One CD-ROM disc containing the following software:  
  Easy CD Creator premastering software for Windows  
  Direct CD drag and drop software for Windows  
  CD Copier CD-to-CD copying software for Windows  
USB Version Package Contents  
  PortaCD-RW portable CD-RW drive  
  AC adapter  
  USB interface cable  
  One blank CD-R disc  
  One blank CD-RW disc  
  Installation software floppy disk  
  TEAC PortaCD-RW User’s Manual (this booklet)  
  Two CD-ROM discs containing the following software:  
For Windows systems:  
  Easy CD Creator premastering software  
  Direct CD drag &drop software  
  CD Copier CD to CD copy for Windows  
For Macintosh systems:  
  Toast premastering software  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
     
USB Version Package Contents  
PortaCD-RW  
Installation software floppy disk  
AC adapter  
USB interface cable  
(ships only with USB version)  
PCMCIA card/cable  
(ships only with PCMCIA version)  
software plus two blank discs  
(only one software disc for PCMCIA version)  
Figure 1. Package Contents  
4
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Power Sources/Battery  
Power Sources/Battery  
This section provides information on the power sources available to the PortaCD-  
RW, including the battery and the AC adapter.  
Power Sources  
The PortaCD-RW drive does not have an On/Off switch. It is ready for operation  
when you connect it to a computer under one of these power sources:  
  AC adapter  
  Charged integrated battery pack  
  Portable computer featuring PCMCIA card technology. (Applicable only for  
the PortaCD-RW PCMCIA version. The USB version can operate only with  
the AC adapter or battery pack; it cannot be powered via the USB cable.)  
Power Settings  
The power supply selection switch has two settings:  
1. Set the power supply selection switch (see page 7) to “Batt./DC” to power  
the drive via the integrated battery pack or the AC adapter. If the AC adapter  
is connected, it will supply power to the drive. If the AC adapter is not con-  
nected and the battery pack is charged, the battery pack will supply power to  
the drive.  
2. Set the power supply selection switch to “PC” to power the drive via the  
PCMCIA cable. (This switch setting position is not available on the  
PortaCD-RW USB version)  
Charging the Battery Pack  
You can charge the integrated battery pack by connecting the AC adapter to the  
drive and plugging the opposite end into an electrical outlet. (You do not need to  
connect the drive to the computer to charge the battery pack.)  
Allow up to five hours for the initial charge time to fully charge an empty battery  
pack. A fully charged battery can last up to two hours.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
       
Removing the Battery Pack  
Removing the Battery Pack  
To remove the battery pack, turn the drive upside down and slide open the battery  
pack cover as illustrated in Figure 2, below.  
Do not use a metal object to pry or remove the battery pack from the PortaCD-RW  
drive. Doing so could short circuit the battery pack or damage the drive.  
Use only TEAC integrated rechargeable battery packs. Standard commercial  
batteries could damage the drive.  
battery compartment cover  
battery  
underside of drive  
Figure 2. Removing the Battery Pack  
6
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Front and Right Panels  
Front and Right Panels  
Figure 3. Front and Right Panels  
Eject button: Pressing the Eject button releases the disc tray from the drive.  
Gently pull the disc tray to open it, or push to close. Some software can  
control disc ejection.  
Caution: Do not pull open or close the disc tray forcefully by hand or you may  
damage the unit. Press the eject button to eject; push the tray gently to close it.  
On/Busy indicator: This LED indicator lights up during seek/data transfer  
and flashes to indicate that the drive is in write mode or playing audio.  
Emergency eject mechanism: To eject a disc when the standard means fail,  
insert a slender, straight tool (such as a straightened paper clip) into the  
emergency eject hole. Press firmly to partially extend the disc tray.  
Power supply selection switch: Use this switch to set the power source for  
the PortaCD-RW drive. Refer to “Power Sources/Battery” on page 5.  
Line out audio/ headphone jack: You can connect headphones or external  
speakers to this 3.5 mm stereo mini-jack.  
AC Power input: Connect the AC adapter to this input.  
Interface connector: The PortaCD-RW comes in either PCMCIA or USB  
interface versions. Connect the appropriate end of the provided PCMCIA or  
USB interface cable to this connector.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
     
Operating Orientation  
Power LED: This LED indicates the power state of the PortaCD-RW, as  
described in the following table.  
LED  
AC Adapter  
Drive  
Disconnected Off  
Powered by battery  
Battery  
—
Off  
Green  
Red  
Not plugged in Connected  
Plugged in  
Disconnected Battery is being charged  
Disconnected Battery is fully charged  
Blinking red Plugged in  
Orange Plugged in  
Connected  
Battery is being charged and drive  
powered by AC adapter  
Green with Plugged in  
blinking  
Connected  
Battery is fully charged and drive pow-  
ered by AC adapter  
orange  
Operating Orientation  
Place the TEAC PortaCD-RW drive on a stable, level surface for operation. The  
surface should be within 10° of horizontal.  
Caution: Do not operate the drive upside-down (i.e., with the TEAC logo fac-  
ing down).  
8
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Chapter 2. Connecting the USB PortaCD-RW Drive to a  
Windows System  
This chapter explains how to connect the USB PortaCD-RW drive to an IBM PC  
compatible computer that features a USB port. It also explains how to install the  
required software drivers.  
(For information on connecting the PCMCIA PortaCD-RW to a PCMCIA-  
equipped PC compatible computer, see “Chapter 3. Connecting the PCMCIA  
PortaCD-RW to a Windows System” on page 23.)  
Connecting the USB PortaCD-RW Drive  
Follow the steps below and refer to your computer's documentation for  
information specific to your system.  
Please read the following instructions thoroughly. The installation procedure  
varies depending on the operating system you are using.  
1. Turn on your computer.  
2. Connect the AC adapter cable to the power input on the PortaCD-RW  
drive.  
To do so, insert the small, female connector of the included AC power cable  
into the power input connector on the side panel of the PortaCD-RW drive.  
Refer to Figure 4 on page 10.  
3. Plug the large end of the USB interface cable into the USB port on the  
rear panel of the PortaCD-RW drive.  
The larger connector on the USB cable features an integrated bridgecard and  
26-pin drive connector. Connect this connector to the PortaCD-RW drive (see  
Figure 4 on page 10).  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
     
Connection Sequence  
1. power cable --> drive  
2. USB cable --> drive  
3. USB cable--> computer  
4. power cable-->AC outlet  
USB cable  
AC adapter cable  
headphone cable  
(not included)  
Figure 4. Connecting Cables (USB version)  
4. Connect the smaller plug on the USB interface cable to a USB port on  
the computer.  
Note: If you are connecting the cable to a USB hub, use a USB hub that  
features an AC Power adapter.  
5. Insert the male plug of the AC power cable into an AC power outlet.  
This step turns on the power to the PortaCD-RW drive and concludes this  
procedure. Please see “Installing the Driver Software” on page 11.  
10  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Connecting and Disconnecting the Drive  
Connecting and Disconnecting the Drive  
The following paragraphs provide information about connecting and  
disconnecting your PortaCD-RW drive.  
Windows 98SE Users:  
You can plug the USB cable into your computer, or unplug it from the computer  
while the computer is running (this is called a “hot plug”). However, do not unplug  
the cable from the drive while the computer is running, or you may damage the  
drive or the computer.  
Windows Me/2000 Professional Users:  
Before you disconnect the drive while the computer is running, you need to  
disable the connection by clicking on the Unplug icon in the Systray (see  
Figure 5):  
Figure 5. Unplug Icon  
All Users:  
Before you disconnect the cable from the computer's USB port, remove any  
inserted discs from the TEAC PortaCD-RW drive.  
Installing the Driver Software  
This section explains how to install the required software drivers in your IBM PC  
compatible computer. The driver software is designed for use with the TEAC USB  
PortaCD-RW drive; it will not work with other drives.  
Notes:  
  If you are using a computer running Windows 98SE/Me, please follow the  
software driver installation instructions in “Installing the Driver Software  
on Windows 98SE/Me Systems” on page 12.  
  If you are using a computer running Windows 2000 Professional, please  
follow the software driver installation instructions in “Installing the Driver  
Software on Windows 2000 Systems” on page 16.  
  Windows 95 and Windows NT are not supported.  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
           
Installing the Driver Software on Windows 98SE/Me Systems  
Installing the Driver Software on Windows 98SE/Me Systems  
Follow these steps to install the software driver on a Windows 98SE/Me system.  
1. Complete the steps described in “Connecting the USB PortaCD-RW  
Drive” on page 9.  
Windows 98SE/Me automatically detects the drive and displays the Add New  
Hardware Installation Wizard (Figure 6).  
Figure 6. Add New Hardware Wizard  
2. Click the Next button.  
The system displays an Add New Hardware Wizard panel that asks if you wish  
to search for the best driver (Figure 7).  
Figure 7. Add New Hardware Wizard: Search for Best Driver  
12  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installing the Driver Software on Windows 98SE/Me Systems  
3. Select the Recommended option, then click the Next button.  
The system displays an Add New Hardware Wizard panel that asks if you want  
to specify the location of the driver software (Figure 8).  
Figure 8. Add New Hardware Wizard: Specify Search Location  
4. Insert the provided floppy diskette, which contains the USB driver soft-  
ware, into the computer’s floppy disk drive.  
5. Select the Floppy disk drive option, then click the Next button.  
Windows locates the FREECOM CABLE USB and is now ready to install the  
drivers on your system (Figure 9).  
Figure 9. Add New Hardware Wizard: Device Search  
6. Click the Next button.  
The system completes the installation of the driver software and displays the  
following panel.  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
   
Installing the Driver Software on Windows 98SE/Me Systems  
Figure 10. Add New Hardware Wizard: Software Installation Finished  
7. Click the Finish button.  
The system displays an icon in the My Computer folder and in the Device  
Manager.  
(You can access the Device Manager using the following menu sequence:  
Start>Settings>Control Panel>System>Device Manager tab. See Figure 11.)  
Your system should now recognize the drive as a CD-ROM drive.  
Device Manager tab  
Figure 11. System Properties Panel  
8. Before you can record to CD-R and CD-RW discs, you must first install  
the Easy CD Creator software.  
For software installation instructions, see “Chapter 4. Installing and Using  
Easy CD Creator 5 Basic on Windows Systems” on page 33.  
14  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Drive Letter Allocation  
Drive Letter Allocation  
Windows 98SE/Me automatically assigns a drive letter to the new drive during the  
installation. In some cases, it may be convenient to re-assign drive letters. To do  
so, follow these steps:  
1. Select Start>Settings>Control Panel>System>Device Manager tab.  
2. Click on the CD-ROM category.  
See Figure 11 on page 14.  
3. Select the TEAC drive item, click the Properties button, then click the  
Settings tab on the Properties panel.  
See Figure 12.  
4. Under Reserved drive letter, specify the desired drive letter for both Start  
drive letter and End drive letter.  
5. Click the OK button to confirm your selection and restart your system.  
Figure 12. Drive Letter Allocation  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
   
Installing the Driver Software on Windows 2000 Systems  
Installing the Driver Software on Windows 2000 Systems  
Follow these steps to install the software drive on a Windows 2000 system.  
1. Complete the steps described in “Connecting the USB PortaCD-RW  
Drive” on page 9.  
Windows 2000 will detect the drive and display the Add New Hardware  
Installation Wizard (Figure 13).  
Figure 13. Found New Hardware Wizard: Welcome  
2. Click the Next button.  
The system displays a panel that asks if you wish to search for the best driver  
(Figure 14).  
Figure 14. Found New Hardware Wizard: Install Hardware Device Drivers  
16  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installing the Driver Software on Windows 2000 Systems  
3. Click the [recommended] option, then click the Next button.  
The system displays a panel that asks if you want to specify the location of  
the driver software (Figure 15).  
Figure 15. Found New Hardware Wizard: Locate Driver Files  
4. Insert the provided floppy diskette, which contains the USB driver soft-  
ware, into the computer’s floppy disk drive.  
5. Select the Floppy disk drives option, then click the Next button.  
Windows locates the FREECOM CABLE USB and displays the following  
panel (Figure 16), ready to install the driver on your system.  
Figure 16. Found New Hardware Wizard: Driver Search Results  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
   
Installing the Driver Software on Windows 2000 Systems  
6. Click the Next button.  
The system displays the Digital Signature panel (Figure 17). The driver  
software is 100% compatible with Windows 2000 Professional.  
Figure 17. Digital Signature Not Found Panel  
7. Click the Yes button on the Digital Signature panel.  
The system completes the installation of the software drivers and displays the  
following panel (Figure 18):  
Figure 18. Found New Hardware Wizard: Completing  
18  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing the Driver Without a Floppy Drive  
8. Click the Finish button to complete the installation.  
The system displays an icon in the My Computer folder and in the Device  
Manager.  
You can access the Device Manager by using the following menu sequence:  
Start>Settings>Control Panel>System>Hardware>Device Manager (see  
Figure 19).  
The system now recognizes the drive as a CD-ROM drive.  
Figure 19. Device Manager  
9. Before you can record to CD-R and CD-RW discs, you must first install  
the Easy CD Creator Pre-Mastering software.  
For software installation instructions, see “Chapter 4. Installing and Using  
Easy CD Creator 5 Basic on Windows Systems” on page 33.  
Installing the Driver Without a Floppy Drive  
If you do not have a floppy disk drive installed on your IBM PC compatible  
system, but you have access to the Internet via the same system, you can download  
the drivers from the TEAC website and save them on your hard disk. You can then  
install the drivers from the hard disk.  
Download the appropriate drivers and installation instructions from the TEAC  
website at:  
http://www.teac.com/dspd  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
   
Uninstalling the USB Driver Software  
Uninstalling the USB Driver Software  
In case you wish to uninstall the driver software, the installation floppy disk  
contains a program named DriverRemove.exe.  
This program uninstalls the USB driver software from an IBM PC compatible.  
You can execute this file directly from the floppy disk drive or from the hard disk.  
1. In Windows Explorer, double-click on the file DriverRemove.exe.  
The system displays the Freecom Driver Remove panel (Figure 20).  
Figure 20. Freecom Driver Remove Panel  
2. Select the Remove Freecom USB Driver option, then click the Start but-  
ton.  
The system advises you on which files to remove (Figure 21).  
Figure 21. Freecom Driver Remove: Remove Actions Panel  
20  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Uninstalling the USB Driver Software  
3. Click the Next button.  
The system advises you to restart your system (Figure 22).  
Figure 22. Freecom Driver Remove: Restart Windows  
4. Select the Restart Windows now option, then click the Finish button.  
5. After you reboot the system, remove the diskette from the floppy disk  
drive.  
TEAC PortaCD-RW Drive User’s Manual  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Uninstalling the USB Driver Software  
22  
TEAC PortaCD-RW Drive User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3. Connecting the PCMCIA PortaCD-RW to a  
Windows System  
This chapter explains how to connect the PCMCIA PortaCD-RW to an IBM PC  
compatible computer that utilizes PCMCIA card technology.  
(For information on connecting the USB PortaCD-RW to a PC compatible  
computer that features a USB port, see “Chapter 2. Connecting the USB PortaCD-  
RW Drive to a Windows System” on page 9.)  
Connecting the PCMCIA PortaCD-RW Drive to a PC  
Please read the following instructions thoroughly. The installation procedure  
varies depending on the operating system you are using.  
1. Connect the PCMCIA cable plug to the interface connector on the side  
panel of the PortaCD-RW (Figure 23).  
2. Do not insert the PCMCIA card into the computer at this time.  
With Windows 98SE/Me/2000, the PortaCD-RW enables you to perform a  
“hot swap” installation while the computer is powered on. You will insert the  
card for the first time later as part of the software installation procedure.  
3. Connect the AC adapter cable to the AC power input on the PortaCD-  
RW drive (Figure 23).  
PCMCIA cable  
AC adapter cable  
headphones cable  
(not included)  
Figure 23. Connecting Cables  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
       
Detecting the PCMCIA Card  
Before you can operate the PortaCD-RW, you must:  
  make sure Windows recognizes the PCMCIA socket, and  
  install the device driver software on your computer’s hard disk.  
To determine whether Windows recognizes the PCMCIA socket in your computer,  
follow these steps, which may vary slightly with your version of Windows.  
1. Select Start>Settings>Control Panel from the pop-up menu.  
The system displays the Control Panel (Figure 24).  
PCMCIA Card icon  
System icon  
Figure 24. Control Panel  
2. Double-click the System icon in the Control Panel.  
The system displays the System Properties panel (Figure 25).  
3. Click the Device Manager tab on the System Properties panel.  
The system displays the Device Manager (Figure 25).  
socket items recognized  
by the system  
Figure 25. System Properties Panel  
24  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
4. Double-click the item PCMCIA Socket on the Device Manager listing.  
The Device Manager displays the PCMCIA Socket items currently recognized  
by the system (see Figure 25 on page 24).  
If an “x” or “!” mark appears on an item, it is not currently recognized by the  
system. In this case, you must install the PCMCIA driver using the PCMCIA  
Card Wizard. (See “Installing the PCMCIA Card Using the Windows PC  
Card Wizard” on page 26.)  
If the TEAC PCMCIA/IDE card is recognized by the system, proceed to  
“Installing the PortaCD-RW Driver Using the Windows Wizard” on page 28.  
Note: If the PCMCIA Card icon does not appear in the Control Panel, try double-  
clicking the Add New Hardware icon and instruct the Wizard to search for new  
hardware.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
Installing the PCMCIA Card Using the Windows PC Card Wizard  
Follow the steps below to install the PCMCIA driver using the PC Card Wizard.  
1. Open the Windows Control Panel by selecting Start>Settings>Control  
Panel from the pop-up menu.  
2. On the Control Panel, double-click the PC Card (PCMCIA) icon.  
The system displays the Welcome to the PC Card (PCMCIA) Wizard panel.  
Figure 26. Welcome to PC Card Wizard  
Follow the instructions on the PC Card Wizard panels to complete the  
installation.  
Note: The system configuration and your dialog responses determine which panels  
the Wizard will display. Do not be concerned if your installation process varies  
slightly from the one described below—just follow the dialog instructions.  
3. Click the Next button.  
The system displays the following panel (Figure 27).  
Figure 27. PC Card Wizard  
26  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
4. Click the Next button.  
The system displays the following panel (Figure 28):  
Figure 28. Installation Complete  
5. Click the Finish button.  
The system displays the following panel (Figure 29):  
Figure 29. System Settings Change  
6. Click the Yes button to shut down the computer.  
The system shuts down the computer.  
7. Wait at least 30 seconds, then restart the computer.  
To fully utilize the drive, you should now install pre-mastering software for  
your Windows system. For more information, see “Chapter 4. Installing and  
Using Easy CD Creator 5 Basic on Windows Systems” on page 33.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
   
For Windows 98SE/Me/2000  
Installing the PortaCD-RW Driver Using the Windows Wizard  
This section explains how to install the PCMCIA driver using the Windows Add  
New Hardware Wizard.  
For Windows 98SE/Me/2000  
The installation procedure for the PCMCIA Card Driver varies depending on the  
version of Windows 98SE/Me/2000 installed in your computer.  
To install the driver on a Windows 98SE/Me/2000 system, follow these steps:  
1. Insert the PCMCIA card into the PCMCIA card slot in your laptop  
computer.  
The other end of the card/cable should already be connected to the interface  
connector on the PortaCD-RW. (If not, see “Chapter 3. Connecting the  
PCMCIA PortaCD-RW to a Windows System” on page 23 for more  
information.)  
The system displays the initial Add New Hardware Wizard panel (Figure 30).  
Figure 30. Add New Hardware Wizard  
Note: The system configuration and your dialog responses determine which panels  
the Wizard will display. Do not be concerned if your installation process varies  
slightly from the one described below—just follow the dialog instructions.  
2. Click the Next button to search for the driver.  
The system displays the following Add New Hardware Wizard panel  
(Figure 31 on page 29), asking what you would like Windows to do:  
28  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
For Windows 98SE/Me/2000  
Figure 31. Search for the Best Driver  
3. Select the Search for best driver option, then click the Next button.  
The system displays the following Add New Hardware Wizard panel  
(Figure 32), asking you to specify the location of the driver:  
Figure 32. Select the Floppy Disk Drive  
4. Insert the TEAC Installation Software for PCMCIA Card floppy diskette in  
your computer’s floppy disk drive.  
5. Select the Floppy disk drives option on the Wizard panel, then click the  
Next button.  
The system displays the following Add New Hardware Wizard panel  
(Figure 33 on page 30), indicating that Windows has located the driver:  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
   
For Windows 98SE/Me/2000  
Figure 33. Driver Located  
6. Click the Next button.  
The system displays the following Add New Hardware Wizard panel  
(Figure 34), indicating the installation is complete:  
Figure 34. Installation Complete  
7. Click the Finish button.  
The system displays the following panel (Figure 35):  
Figure 35. System Settings Change  
8. Click the Yes button to shut down the computer.  
The system shuts down the computer.  
30  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
For Windows 98SE/Me/2000  
9. Remove the floppy diskette and start the computer.  
After you start the computer, the system will assign a new drive letter and  
icon to the PortaCD-RW drive.  
To fully utilize the drive, you should now install pre-mastering software for  
your Windows system. For more information, see “Chapter 4. Installing and  
Using Easy CD Creator 5 Basic on Windows Systems” on page 33.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
For Windows 98SE/Me/2000  
32  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4. Installing and Using Easy CD Creator 5 Basic  
on Windows Systems  
Note: The CD Recording software included in this package will work on systems  
on which Windows 2000-Professional has been fully installed. It will not work  
on systems on which Windows 2000 has been installed by upgrading earlier  
versions of Windows (i.e., Windows 98SE). This software will not work with  
Windows 2000 Server, Advanced Server, Datacenter Server, or Windows NT 4.0  
Server.  
Before installing the software, please make sure that the TEAC PortaCD-RW  
drive is properly installed as per the instructions in “Chapter 2. Connecting the  
USB PortaCD-RW Drive to a Windows System” on page 9 or “Chapter 3.  
Connecting the PCMCIA PortaCD-RW to a Windows System” on page 23.  
To record data or audio onto CD-R or CD-RW discs using your PortaCD-RW  
drive, you need to use pre-mastering software, such as Easy CD Creator 5 Basic.  
Your kit includes a CD-ROM that contains Easy CD Creator 5 software  
applications for Windows 98SE, Windows Me, Windows NT 4.0 Workstation, and  
Windows 2000-Professional systems.  
Easy CD Creator 5 Basic is a premastering software application that enables you  
to:  
  create audio/music CDs  
  create data CDs to archive data files  
  drag-and-drop files onto a CD-R or CD-RW disc using directCD  
  create duplicate copies of discs, assuming you have a second CD-ROM  
drive, using CD Copier software  
Uninstalling Old Versions of Easy CD Creator  
If you have an old version of Easy CD Creator (and/or other recording software)  
on your system, you must uninstall it before you install Easy CD Creator 5.  
To uninstall the old version of Easy CD Creator, select:  
Start > Programs > Adaptec Easy CD Creator 4 (or your version) > Uninstall  
The system displays the Control Panels window. Use the Add/Remove Programs  
utility to uninstall the old program. For additional information, refer to your  
Windows documentation.  
Alternatively, you can uninstall the program using the Add/Remove Program tool  
in the Control Panel.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
     
Installing Easy CD Creator 5 Software  
Installing Easy CD Creator 5 Software  
Before you install Easy CD Creator 5 Basic, disable any applications that may be  
running in the background, including anti-virus software, screen savers,  
schedulers, etc.  
To do so, press CTL-ALT-DEL on your keyboard. The Close Program panel will  
display a list of all current programs in memory (Figure 36). With the exception  
of “Explorer” and “Systray,” select each program, then click the End Task button.  
Then proceed with the installation below.  
Figure 36. Close Program Panel  
Follow these steps to install Easy CD Creator 5 software on your computer’s hard  
disk.  
1. Insert the Easy CD Creator 5 CD-ROM into your computer’s CD-ROM  
drive or into the PortaCD-RW drive.  
If the Autoplay function is enabled, the system displays the auto detect screen  
(Figure 37). Click Yes to continue.  
Figure 37. Auto Detect Panel  
If the auto detect panel is not displayed, double-click the My Computer icon,  
then double-click the icon for the CD-ROM drive, and double-click on  
setup.exe.  
The system displays the following Choose Setup Language panel  
(Figure 38 on page 35).  
34  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installing Easy CD Creator 5 Software  
Figure 38. Choose Setup language Panel  
2. Select a language and click the OK button.  
The system displays the following installShield Wizard Welcome panel  
(Figure 39):  
Figure 39. InstallShield Wizard Welcome Panel  
3. Click the Next button.  
The system displays the following panel (Figure 40):  
Figure 40. Setup Type Panel  
TEAC PortaCD-RW User’s Manual  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installing Easy CD Creator 5 Software  
4. Select a setup type, then click the Next button.  
The system verifies that you wish to begin the installation (Figure 41).  
Figure 41. Ready to Install Panel  
5. Click the Install button.  
The system begins the installation and displays a bar graph marking progress  
(Figure 42):  
Figure 42. Installing Status Panel  
If you wish to abort the installation, click the Cancel button any time. When  
installation is complete, the system displays the following panel  
(Figure 43 on page 37):  
36  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing Easy CD Creator 5 Software  
:
Figure 43. InstallShield Wizard Completed Panel  
6. Click the Finish button to exit InstallShield Wizard.  
The system advises you to restart the computer to use Easy CD Creator 5.  
Figure 44. Restart Panel  
7. Click the Yes button to restart the computer.  
Once the system reboots, Easy CD Creator 5 is ready for use.  
Online Registration  
There is no need to register any portion of this kit. TEAC provides 100% support  
for the drive and the Roxio software. If a Registration Reminder panel appears  
when you launch the Easy CD Creator 5 Basic software, check the Do not show  
this reminder again box and close the Registration Reminder panel. Refer to the  
“Technical Support” section on page 64 if you wish to contact TEAC.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37  
     
Starting Easy CD Creator 5  
Starting Easy CD Creator 5  
To start Easy CD Creator 5:  
1. Click the Start button on the Windows task bar, and select from the pop-  
up menu: Programs > Roxio Easy CD Creator 5 > Project Selector.  
The system displays the Select a Project panel for Easy CD Creator 5 Basic  
(Figure 45 on page 39), which enables you to create audio or data discs and  
perform other functions. (Alternatively, to start the program you can double-  
click the Easy CD Creator shortcut on the desktop.)  
For information on using each function, please see Figure 45 on page 39 and  
“About the Help Files (help button)” on page 40.  
Using Easy CD Creator 5  
Your copy of Easy CD Creator 5 Basic enables you to:  
  Create custom audio CDs from audio tracks, MP3 files, or WAV files.  
  Create data CDs from graphic images, photos, video clips, or your personal  
files.  
  Use DirectCD to drag-and-drop files to CD as simply as you copy files to a  
standard floppy disk.  
  Copy CDs using CD Copier (an additional CD-ROM or DVD-ROM drive is  
required with DAE support).  
  Download the latest drive support and software updates (Internet access  
required)  
  Purchase the upgrade to the Platinum version of Easy CD Creator 5  
  Access the on-line Help system for more information  
See Figure 45 on page 39.  
38  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Starting Easy CD Creator 5  
With Easy CD Creator 5 Basic, you can do the follow ing:  
Create data CDs in several formats. For example, you can create discs  
that contain graphic images or photographs in various file formats.  
You can also backup or archive any type of file.  
Download the latest drive support and software updates via the Internet.  
Upgrade to CD Creator Platinum.  
Create custom audio CDs from audio tracks, MP3 files, or WAV files.  
Access the on-line  
Help system.  
If you upgrade to CD Creator  
Platinum, you can create  
photo albums and video  
postcards.  
If you upgrade to CD Creator  
Platinum, you can create  
labels for your CDs.  
However, you can record  
video files to CD using  
the “make a data cd” function.  
Legend  
Easy CD Creator 5 Basic  
With an additional CD-ROM drive,  
you can duplicate discs.  
Easy CD Creator 5 Platinum  
Figure 45. Easy CD Creator Select a Project Panel  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
 
About the Help Files (help button)  
About the Help Files (help button)  
This document explains the basic operations of Easy CD Creator 5. To learn more,  
refer to the extensive on-line Help system.  
Before you install the program, you can access the Help files by using a browser  
such as Netscape Navigator or Internet Explorer to open the Help/enu_basic on the  
CD-ROM.  
After you install the program, you can better access the Help system by clicking  
the Help menu in the selected program.  
The Select a Project panel (Figure 45 on page 39) features a Help button that links  
to additional information about Easy CD Creator.  
To access on-line help:  
1. On the Select a Project panel (Figure 45 on page 39), position the cursor  
over the help rollover button in the lower right corner.  
The system displays the help button and a brief description of the on-line help  
(Figure 45):  
help button  
help rollover button  
Figure 46. Select a Project Panel: Help Button  
2. Click the help button.  
The system displays the Help Topics panel (Figure 47 on page 41):  
40  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
About the Help Files (help button)  
click to expand  
a topic  
Figure 47. Help Topics Panel  
3. Click a topic in the left column to expand the topic list. Click an item to  
display detailed information in the right column.  
Creating Audio Discs (make a music CD button)  
Easy CD Creator 5 Basic enables you to create audio CDs from various sources,  
including MP3 files, WAV, WMA, or directly from pre-recorded compact discs.  
When you roll over the make a music CD button on the Select a Project panel, the  
system highlights the button and displays the musicCD button (Figure 48). This  
button enables you to create music CDs, and save your record list between burns.  
Two other buttons are also displayed on the panel with a screened or “greyed-out”  
appearance. These buttons link to additional functionality available only in the  
upgraded Platinum version of Easy CD Creator 5. This functionality may simplify  
or enhance the process of creating certain discs. However, the core functions  
contained in Easy CD Creator 5 Basic enable you to work with MP3 files and most  
other files types to create audio CDs.  
Create music CDs  
from various sources,  
including MP3, WAV,  
or WMA files, or  
pre-recorded compact  
discs.  
Figure 48. Select a Project Panel: Make Music CD  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
41  
     
Creating Music CDs (musicCD button)  
Creating Music CDs (musicCD button)  
To create music CDs:  
1. Roll over the make a music CD button on the main Select a Project panel  
(Figure 48 on page 41).  
The system displays the musicCD project button (Figure 48 on page 41).  
2. Click the musicCD project button.  
The system displays an Untitled Music CD Project panel (Figure 49). For more  
information, click the Help menu on the toolbar and select Content and Index.  
Figure 49. Untitled Music CD Project Panel  
Creating Data Discs (make a data CD button)  
Easy CD Creator 5 enables you to create data archive CDs and backup your  
important data to CDs in three easy ways. When you roll the cursor over the make  
a data CD button on the Select a Project panel (Figure 50 on page 43), the system  
displays buttons for the following functions:  
  directCD enables you to format a blank disc so you can drag files to a CD-R  
or CD-RW using Windows Explorer.  
  dataCD enables you to share or archive your computer files on CDs in the  
most compatible format.  
Note: A button for take two software is also displayed on the panel with a  
screened or “greyed-out” appearance. This button links to additional  
functionality available only in the upgraded Platinum version of Easy CD  
Creator 5.  
42  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Formatting Blank Discs for Use With DirectCD (directCD button)  
Drag-and-drop  
files to CD!  
Create a data CD  
that contains any  
type of computer file,  
including digital videos  
and photos, text files,  
graphic files, etc.  
Figure 50. Select a Project Panel: Make a Data CD Button  
Formatting Blank Discs for Use With DirectCD (directCD button)  
If you format a disc for use with DirectCD, you can just drag files to the CD using  
Windows Explorer.  
To format a DirectCD disc:  
1. Roll over the make a data CD button on the main Select a Project panel  
(Figure 45 on page 39).  
The system highlights the make a data CD button and displays three project  
buttons (Figure 50).  
2. Click the directCD button.  
The system displays the DirectCD format utility panel (Figure 51). For more  
information, click the help button illustrated in Figure 51.  
Help button  
Figure 51. DirectCD Format Utility Panel  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
     
Creating Archive CDs (dataCD button)  
Creating Archive CDs (dataCD button)  
You can share or archive your computer files on CD-R or CD-RW discs using  
various formats.  
To create an archive disc:  
1. Roll over the make a data CD button on the main Select a Project panel  
(Figure 45 on page 39).  
The system highlights the make a data CD button and displays three project  
buttons (Figure 50 on page 43).  
2. Click the dataCD button.  
The system displays an Untitled Data CD project panel (Figure 52). For more  
information, click the Help menu on the toolbar and select Content and Index.  
Figure 52. Untitled Data CD Project Panel  
44  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Creating Photo or Video CDs (make a photo or video CD button)  
Creating Photo or Video CDs (make a photo or video CD button)  
If you upgrade to the Platinum version of Easy CD Creator 5 as described in  
“Upgrading the Software (upgrade button)” on page 47, the make a photo or  
video CD button is activated, which facilitates editing and saving video files to  
disc.  
However, you do not need the Platinum version to create custom video CDs. The  
make a data CD feature of Easy CD Creator 5 Basic enables you to create discs  
containing video files in all popular formats, including Quicktime, AVI, MPEG,  
etc.  
Figure 53. Select a Project: Make a Photo or Video CD Button  
Copying Discs (CD copier button)  
You can make a backup copy of an entire CD with a single click.  
To copy a disc:  
1. Roll over the CD copier button on the main Select a Project panel  
(Figure 45 on page 39).  
The system highlights the CD copier rollover button and displays the CD  
copier button.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
45  
     
Creating Photo or Video CDs (make a photo or video CD button)  
CD copier button  
CD copier rollover  
Figure 54. Select a Project: CD Copier Button  
2. Click the CD copier button.  
The system displays the Welcome panel (Figure 55), which warns against  
copyright infringement.  
Figure 55. CD Copier Welcome Panel  
3. Please read the panel, then click the OK button.  
The system displays the CD Copier (Figure 56) panel. For more information,  
click the Help menu on the toolbar and select Help topics.  
Figure 56. CD Copier Panel  
46  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Creating Photo or Video CDs (make a photo or video CD button)  
Upgrading the Software (upgrade button)  
If your computer has access to the Internet, you can upgrade Easy CD Creator 5  
Basic to Easy CD Creator Platinum by clicking the upgrade button on the Select  
a Project panel and following the instructions.  
Roxio will handle technical support for Easy CD Creator 5 Platinum directly.  
Updating the Software (web-checkup button)  
If your computer has access to the Internet, you can download the latest software  
updates for Easy CD Creator 5.  
To download the latest software update:  
1. Roll over the web-checkup button on the main Select a Project panel  
(Figure 45 on page 39).  
The system displays another web-checkup button and a short description of  
the web-checkup function (Figure 57).  
Figure 57. Select a Project: Web-checkup Button  
2. Click the web-checkup button and follow the instructions on the web  
page to download the software updates.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
47  
     
Creating CD Labels (CD label creator button)  
Creating CD Labels (CD label creator button)  
If you upgrade to the Platinum version of Easy CD Creator 5 as described above,  
the CD Label Creator button is activated, enabling you to create CD labels and  
design CD jackets.  
CD Label Creator rollover  
Figure 58. Select a Project: CD Label Creator Button  
Uninstalling Easy CD Creator 5  
To uninstall Easy CD Creator 5, use the Add/Remove Program tool in the Control  
Panel. Follow these steps:  
1. Select Start>Settings>Control Panel.  
2. Double-click the Add/Remove Program icon.  
3. Click Easy CD Creator 5 Basic.  
4. Click the Add/Remove button.  
48  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Chapter 5. Connecting the USB PortaCD-RW to and  
Installing Software on Macintosh Systems  
You can connect the USB version of the TEAC PortaCD-RW to an Apple Power  
Macintosh iBook, iMac, PowerBook, or G3 or G4 computer that features a USB  
port.  
Note: You cannot interface the PCMCIA version of this drive to a Macintosh  
system. The Macintosh does not support the PCMCIA interface.  
Connecting to a Macintosh System  
Follow these steps:  
1. Connect the appropriate end of the USB cable to the USB interface con-  
nector on the side panel of the PortaCD-RW (Figure 59).  
2. Insert the USB cable into a USB port on your Macintosh computer.  
Note: Connect the cable directly to the USB connector on your Macintosh  
or self-powered USB hub. Do not connect the cable to the USB connector on  
the keyboard. See your Macintosh documentation for more information.  
3. Connect the AC adapter cable to the AC power input on the PortaCD-  
RW drive (Figure 59).  
Connection Sequence  
1. power cable --> drive  
2. USB cable --> drive  
3. USB cable--> computer  
4. power cable-->AC outlet  
USB cable  
AC adapter cable  
headphones cable  
(not included)  
Figure 59. Connecting Cables  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
49  
 
Before You Disconnect the Cable from the Computer’s USB Port  
4. Plug the AC adapter cable into a power outlet.  
This turns on the power to the PortaCD-RW drive and concludes the  
procedure for physically connecting the drive to your Apple Macintosh  
computer.  
There is no need to install a software driver. This functionality is contained  
within the Mac OS. However you need to install Toast pre-mastering  
software. See “Installing Toast Software” on page 51 for more information.  
Before You Disconnect the Cable from the Computer’s USB Port  
Before you disconnect the cable from the computer’s USB port, remove any  
inserted discs from the PortaCD-RW drive.  
50  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing Toast Software  
Installing Toast Software  
Before you can record data onto CD-R or CD-RW discs using your Macintosh  
computer and your TEAC PortaCD-RW drive, you must first install TEAC/ Toast  
Software for Macintosh onto your Macintosh computer’s hard disk.  
The kit includes a CD-ROM that contains the Toast recording software for  
Macintosh systems. Toast is a full-featured premastering software application that  
enables you to create audio and data CD-R and CD-RW discs.  
Note: Before you install Toast, disable any applications that may be running in  
the background, including anti-virus software, screen savers, schedulers, etc.  
This will ensure the proper installation of the Toast software.  
Follow the steps below to install Toast software on your Macintosh computer’s  
hard disk.  
1. Insert the TEAC/Toast Software for Macintosh CD-ROM into your com-  
puter’s CD-ROM drive or into the PortaCD-RW drive.  
After the system loads the disc, it displays the Toast 4.1.2 CD-ROM icon on  
the Macintosh desktop (Figure 60).  
Figure 60. Toast Software Icon  
2. Double-click the Toast CD-ROM icon.  
The system displays the Toast 4.1.2 main installation panel (Figure 61 on  
page 52).  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
51  
   
Installing Toast Software  
Figure 61. Toast Main Installation Panel  
3. Double-click the installer in your desired language.  
The system displays a continuation panel (Figure 62 on page 52).  
Figure 62. Continuation Panel  
4. Click the Continue button.  
Toast 4.1.2 installs an English language version of the software.  
Toast-F installs a French (Français) version; Toast-D installs a German  
(Deutsch) version. The system then displays a license agreement.  
5. Please read the License Agreement, and if you agree to its terms, click  
the Accept button.  
The system displays a Read Me/Registration panel (Figure 63 on page 53).  
52  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing Toast Software  
Figure 63. Read Me/Registration Panel  
6. Click the Continue button.  
The system displays the Toast 4.1.2 Installer panel (Figure 64).  
Figure 64. Toast 4.1.2 Installer Panel  
7. Select the Full Install option by using the pull-down menu in the upper-  
right corner of the panel.  
8. If desired, specify a location on the hard drive as the installation desti-  
nation by using the Install Location pull-down menu.  
9. Click the Install button.  
The system begins to install the software onto your computer’s hard drive  
while displaying the following panel (Figure 65 on page 54):  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
53  
   
Installing Toast Software  
Figure 65. Installing Panel  
If the installation is successful, the system then displays an Installation  
successful panel (Figure 66).  
Figure 66. Installation Successful Panel  
10. Click the Quit button to conclude the installation.  
Starting Toast  
To start Toast, follow these steps:  
1. Double-click the Toast 4.1.2 folder icon.  
The system opens the Toast 4.1.2 folder (Figure 67).  
Toast  
Figure 67. Toast Folder  
54  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installing Toast Software  
2. Double-click the Toast 4.1.2 application icon.  
The system loads the Toast software and displays the main panel (Figure 68).  
Figure 68. Toast Main Panel  
For information on using Toast, refer to the user’s guide in the  
documentation.pdf file in the Toast 4.1.2 folder.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
55  
 
Installing Toast Software  
56  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6. Connecting to Audio Equipment  
The PortaCD-RW drive outputs a stereo audio signal from the left and right phono  
connectors on the right panel. Connect these outputs to the left and right channel  
inputs on a mixer, amplifier, or powered-speakers.  
The PortaCD-RW drive outputs a line-level audio signal from the headphone jack  
on its side panel. You can connect headphones or external powered-speakers to  
the headphone jack, which accepts a 3.5mm stereo mini-plug.  
Alternatively, if your computer contains a sound card that features audio output  
jacks, you can connect the external powered-speakers to the audio connectors of  
the computer.  
Figure 69. Connecting Analog Audio Speakers or Headphones  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
57  
   
58  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7. Handling, Loading, and Ejecting Discs  
This section explains how to handle, load, and eject discs from the PortaCD-RW.  
Handling Discs  
  Handle compact discs only by their edges to avoid getting fingerprints on the  
surface. Do not touch the disc’s data surface (non-label side).  
  Do not place discs in direct sunlight, or in locations subject to high humidity,  
high temperatures, or dusty conditions.  
  If cleaning the disc becomes necessary (erratic operation or visible dust or  
smudges), gently wipe the surface of the disc from the center to the outside  
edge. Do not use benzene, alcohol, thinner, or other solvents.  
handle discs only by their  
inner or outer edges  
wipe disc surface from  
center to outside edge  
Figure 70. Handling Discs  
TEAC PortaCD-RW User’s Manual  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Loading and Ejecting Discs  
Loading and Ejecting Discs  
This section explains how to load and eject discs from the PortaCD-RW.  
Loading a Disc  
1. Press the Open/Eject button on the front panel.  
The PortaCD-RW partially extends the disc tray. Grasp the front bezel and  
slide the tray fully open.  
Figure 71. Extending the Disc Tray  
2. Insert a CD-R, CD-RW, CD-ROM or audio CD into the drive. Make  
sure the disc label faces up.  
Press the disc gently down onto the spindle, if necessary, until it snaps  
securely into position.  
3. Gently push the tray to retract it into the drive.  
Figure 72. Inserting a Disc  
60  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Ejecting a Disc  
Ejecting a Disc  
1. To eject a disc, first make sure the disc has stopped spinning. Then press  
the Open/Eject button on the front panel.  
The PortaCD-RW partially extends the disc tray. Grasp the front bezel and  
slide the tray fully open.  
2. Carefully remove the disc.  
You may need to press a finger on the spindle or chassis to stabilize the drive.  
3. Gently push the tray to retract it into the drive.  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61  
 
Recommended Media  
Recommended Media  
One blank TEAC CD-R disc and one CD-RW rewritable disc are included in the  
package with your PortaCD-RW.  
Use only 74 or 80-minute blank CD-R and CD-RW media from TEAC or the  
following manufacturers:  
Disc Type Manufacturer  
Disc Type Manufacturer  
CD-R  
Taiyo Yuden  
Mitsui Toatsu Chemical  
Mitsubishi (Verbatim)  
Ricoh  
CD-RW  
Mitsubishi (Verbatim)  
Ricoh  
TDK Electronics  
Kodak  
Fuji Film  
Hitachi (Maxell)  
Pioneer  
Sony  
Maxell  
PVC  
Note: You may purchase additional TEAC media online at www.shopteac.com.  
Disc Formats  
The TEAC PortaCD-RW drive supports the following disc formats:  
Disc Format  
Data Capacity  
CD-DA  
74 or 80 minutes  
650MB or 700MB  
650MB or 700MB  
738MB or 794MB  
650MB or 700MB  
650MB or 700MB  
650MB or 700MB  
650MB or 700MB  
650MB or 700MB  
650MB or 700MB  
650MB or 700MB  
CD-ROM Mode 1  
CD-ROM XA Mode 2 (Form 1)  
CD-ROM XA Mode 2 (Form 2)  
CD-R  
CD-RW  
CD-I  
Video-CD  
CD Extra/CD-Plus  
CD-TEXT  
Multi-session Photo CD  
62  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Specifications  
Model  
CDWE24E  
Interface  
ATAPI (drive side)  
PCMCIA Card Type II or USB 1.1  
Transfer Rate  
Write and Rewrite: 4X (600KBps)  
Read: PCMCIA version: 24X maximum (3,600KBps)  
USB version: 6X maximum (900KBps)  
Access Time  
Buffer Size  
Disc Type  
110 msec (1/3 Stroke)  
2MB  
CD-DA; CD-ROM (Mode-1, Mode-2); CD-ROM XA Mode-2  
(Form-1, Form-2); PhotoCD (Multisession and Single ses-  
sion); CD-I; Video CD; CD Extra; CD Text; Mixed Mode CD  
Write Methods  
Track At Once; Disk At Once; Multi-Session; Incremental  
Write Verification  
Running Optimum Power Control to dynamically adjust laser  
write power  
Logical Recording  
Format  
IS09660, UDF & CDR-FS Packet Write  
Disc Diameter  
Disc Loading  
Drive Features  
12 cm, 8 cm  
Tray (caddy not required)  
Built-in Headphone Jack, Status LEDs, and Re-chargeable  
battery pack  
Headphone Jack  
Installation  
3.5mm diameter stereo mini-headphone jack  
Horizontal, plus or minus 10°  
5.35”(W) x 0.78”(H) x 6.81”(D)  
1.1 lbs.  
Dimensions  
Weight  
Relative Humidity  
Operating: 8% to 80% (non-condensing), wet bulb tempera-  
ture 29.4°C  
MTBF  
60,000 POH  
Safety Standard  
Approved by UL  
Specifications and features subject to change without notice or obligation.  
TEAC PortaCD-RW User’s Manual  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Technical Support  
For technical support, please contact the dealer from whom you purchased the  
drive or the TEAC Service and Support Center nearest you:  
TEAC America, Inc. (USA)  
Technical Support  
Telephone: (323) 727-4860  
Fax: (323) 869-8751  
Monday - Friday 8:00 a.m. - 5:00 pm PST  
http://www.teac.com/dspd  
E-mail: [email protected]  
64  
TEAC PortaCD-RW User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   

Tascam DVR DR 07 User Manual
Teac Recording Equipment UD 501 User Manual
Toshiba Car Video System SD3300 User Manual
Trane Air Conditioner SS PRC003 EN User Manual
Trane Ventilation Hood 1500 CFM User Manual
Traulsen Refrigerator UL Series User Manual
Triarch Indoor Furnishings 29272 User Manual
Troy Bilt Yard Vacuum 24B 060F063 User Manual
Turbosound Speaker TA 500 User Manual
Viking Ventilation Hood VGRT482 4G User Manual