D01252220A
DR-680
"
)
Portable Multitrack Recorder
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1
2
3
4
5
6
7
Read these instructions.
The apparatus draws nominal non-operating
power from the AC outlet with its POWER or
STANDBY/ON switch not in the ON position.
The mains plug is used as the disconnect device,
the disconnect device shall remain readily opera-
ble.
Caution should be taken when using earphones
or headphones with the product because exces-
sive sound pressure (volume) from earphones or
headphones can cause hearing loss.
•
•
•
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
If you are experiencing problems with this prod-
uct, contact TEAC for a service referral. Do not
use the product until it has been repaired.
Do not block any ventilation openings. Install in accor-
dance with the manufacturer's instructions.
•
8
9
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
CAUTION
•
•
•
•
Do not expose this apparatus to drips or
splashes.
Do not place any objects filled with liquids, such
as vases, on the apparatus.
Do not install this apparatus in a confined space
such as a book case or similar unit.
The apparatus should be located close enough
to the AC outlet so that you can easily grasp the
power cord plug at any time.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safe-
ty. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
•
•
If the product uses batteries (including a battery
pack or installed batteries), they should not be
exposed to sunshine, fire or excessive heat.
CAUTION for products that use replaceable
lithium batteries: there is danger of explosion
if a battery is replaced with an incorrect type
of battery. Replace only with the same or
equivalent type.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the appara-
tus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the appa-
ratus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
WARNING
•
Products with Class ! construction are equipped
with a power supply cord that has a grounding
plug. The cord of such a product must be
plugged into an AC outlet that has a protective
grounding connection.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-680
3
IMPORTANT SAFETY INSTRUCTIONS
8
CAUTIONS ABOUT BATTERIES
For European Customers
This product uses batteries. Misuse of batteries could
cause a leak, rupture or other trouble. Always abide by the
following precautions when using batteries.
Disposal of electrical and electronic equipment
(a) All electrical and electronic equipment should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed by
the government or the local authorities.
(b)By disposing of the electrical and electronic equipment
correctly, you will help save valuable resources and
prevent any potential negative effects on human
health and the environment.
(c) Improper disposal of waste equipment can have
serious effects on the environment and human health
as a result of the presence of hazardous substances in
electrical and electronic equipment.
(d) The crossed out wheeled dust bin symbol
indicates that electrical and electronic
equipment must be collected and disposed of
separately from household waste.
•
Never recharge non-rechargeable batteries. The
batteries could rupture or leak, causing fire or injury.
•
When installing batteries, pay attention to the polarity
indications (plus/minus (¥/^) orientation), and install
them correctly in the battery compartment as indicated.
Putting them in backward could make the batteries
rupture or leak, causing fire, injury or stains around
them.
•
When you store or dispose batteries, isolate their
terminals with insulation tape or something like that to
prevent them from contacting other batteries or metallic
objects.
•
•
When throwing used batteries away, follow the disposal
instructions indicated on the batteries and the local
disposal laws.
Do not use batteries other than those specified. Do not
mix and use new and old batteries or different types of
batteries together. The batteries could rupture or leak,
causing fire, injury or stains around them.
(e) The return and collection systems are available
to the end users. For more detailed information about
disposal of old electrical and electronic equipment,
please contact your city office, waste disposal service
or the shop where you purchased the equipment.
•
•
•
Do not carry or store batteries together with small metal
objects. The batteries could short, causing leak, rupture
or other trouble.
Do not heat or disassemble batteries. Do not put them in
fire or water. Batteries could rupture or leak, causing fire,
injury or stains around them.
If the battery fluid leaks, wipe away any fluid on the
battery case before inserting new batteries. If the battery
fluid gets in an eye, it could cause loss of eyesight. If
fluid does enter an eye, wash it out thoroughly with
clean water without rubbing the eye and then consult a
doctor immediately. If the fluid gets on a person’s body
or clothing, it could cause skin injuries or burns. If this
should happen, wash it off with clean water and then
consult a doctor immediately.
Disposal of batteries and/or accumulators
(a) Waste batteries and/or accumulators should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed by
the government or the local authorities.
(b)By disposing of waste batteries and/or accumulators
correctly, you will help save valuable resources and
prevent any potential negative effects on human
health and the environment.
(c) Improper disposal of waste batteries and/or accumu-
lators can have serious effects on the environment and
human health as a result of the presence of hazardous
substances in batteries and/or accumulators.
(d) The crossed out wheeled dust bin symbol
indicates that batteries and/or accumulators
must be collected and disposed of separately
from household waste.
•
•
The unit power should be off when you install and
replace batteries.
Remove the batteries if you do not plan to use the unit
for a long time. Batteries could rupture or leak, causing
fire, injury or stains around them. If the battery fluid
leaks, wipe away any fluid on the battery compartment
before inserting new batteries.
Pb, Hg, Cd
If the battery or accumulator contains more
than the specified values of lead (Pb), mercury (Hg),
and/or cadmium (Cd) defined in the Battery Directive
(2006/66/EC), then the chemical symbols for lead (Pb),
mercury (Hg) and/or cadmium (Cd) will be indicated
beneath the crossed out wheeled dust bin symbol.
•
Do not disassemble a battery. The acid inside the battery
could harm skin or clothing.
(e) The return and collection systems are available to
the end users. For more detailed information about
disposal of waste batteries and/or accumulators, please
contact your city office, waste disposal service or the
shop where you purchased them.
TASCAM DR-680MKIIDownload from Www.Somanuals.com. All Manuals Search And Download.
4
Contents
Turning the built-in speaker output on
1 – Introduction ........................................ 7
and off.......................................................................... 23
Connecting monitoring equipment ................. 23
Adjusting the display contrast ............................ 23
Features..........................................................................7
Items included with the product ..........................7
Conventions used in this manual..........................7
Intellectual property rights.....................................8
About SD cards ............................................................8
Precautions for use..............................................8
Precautions for placement and use......................9
Beware of condensation...........................................9
Cleaning the unit.........................................................9
User registration..........................................................9
4 – Recording .......................................... 24
Files and takes............................................................24
Recording settings....................................................24
Setting the recording file format..................24
Setting the sampling frequency ................. 25
Setting the file recording mode .................. 25
Stereo track recording settings.................... 25
2 – Names and Functions of Parts ......... 10
Arming and disarming tracks
for recording....................................................... 25
Top panel .....................................................................10
Front panel .................................................................11
Left side panel ...........................................................12
Right side panel ........................................................13
Bottom panel .............................................................14
Home Screen .............................................................15
Menu structure ..........................................................16
Using menus...............................................................17
Operation basics .......................................................18
Functions Screen.......................................................18
Repeat activation ...............................................18
Pre-record activation........................................18
Auto-record activation.....................................18
DIN/MIX monitor settings...............................19
Limiter activation ...............................................19
Low-cut filter activation ..................................19
Creation of new takes when restarting
recording...............................................................26
Setting the name given to recording
takes........................................................................26
Editing the user take names...........................27
Resetting take name numbering ........................27
Available recording time display..................27
Set the folder for saving takes..............................27
Connecting other equipment ............................. 28
Input settings ............................................................ 28
Setting the input sources............................... 28
Phantom power................................................. 28
Selecting the inputs for recording
to tracks 5 and 6 ................................................ 29
Adjusting the input levels..................................... 29
Recording a take....................................................... 30
Recording a stereo mix ...........................................31
Simultaneously recording two files
3 – Preparations...................................... 20
Powering the unit .................................................... 20
About the power supply ................................ 20
Using AA batteries............................................ 20
Using the AC adaptor....................................... 20
Changing the outlet plug................................21
at different input levels (DUAL REC)...................31
Enabling dual recording ..................................31
Starting dual recording....................................32
Dual recording take names ............................32
Using the solo function ..........................................32
Automatically starting and pausing recording
(auto-record function).............................................32
Using the auto-record function....................32
Turning the power on and putting the unit
into standby................................................................21
Turning the power on.......................................21
Putting the unit into standby ........................21
Inserting and removing SD cards........................21
Inserting an SD card .........................................21
Ejecting an SD card........................................... 22
Preparing an SD card for use ............................... 22
Card write-protection...................................... 22
Setting the date and time..................................... 22
Auto-record settings.........................................32
Automatically cutting unnecessary silences
when recording (silent cut function) ..........33
Automatically adding marks at the
position where recording restarts ...............33
Track incrementation.............................................. 34
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-680
5
Contents
Manually incrementing tracks during
Ending the connection with a computer........ 44
recording.............................................................. 34
8 – Cascade function............................... 45
Automatically incrementing tracks by file
size.......................................................................... 34
Preparing to use the cascade function .............45
Cascade recording....................................................45
Cascade playback .....................................................45
Disabling cascade operation ................................45
Precautions for use of the cascade function.. 46
Using the limiter....................................................... 34
Using the low-cut filter ...........................................35
Turning the low-cut filter on and off...........35
Setting the cut-off frequency of the
low-cut filter.........................................................35
9 – Other Settings and Information
Using marks ................................................................35
Manually adding marks when recording
and during playback ........................................35
Display..................................................... 47
Using mid-side mic decoding...............................47
Connecting a mid-side microphone...........47
Setting the MS decoding mode .........................47
Recording with mid-side decoding....................47
GANG function.......................................................... 48
Output settings ........................................................ 48
Analog output settings................................... 48
Digital output settings.................................... 49
System settings......................................................... 49
Power AUTO OFF settings.............................. 49
Turning the backlight off automatically ... 49
Cascade settings................................................ 50
Moving to a mark ..............................................35
Erasing marks ..................................................... 36
Pre-recording ............................................................ 36
Recording times ........................................................37
5 – Take and folder operations
(BROWSE screen)..................................... 38
Navigating the BROWSE screen.......................... 38
Icons on the BROWSE screen............................... 38
Take operations ........................................................ 38
Folder operations......................................................39
Setting the extent of the panel operation
lock function....................................................... 50
6 – Playback............................................. 40
Playback....................................................................... 40
Starting playback .............................................. 40
Stopping playback............................................ 40
Pausing playback............................................... 40
Searching forward and backward............... 40
Selecting a take for playback........................ 40
Setting the battery type................................. 50
Initializing the unit............................................ 50
Viewing system information......................... 50
Reformatting SD cards............................................51
Viewing SD card information................................51
10 – Messages ......................................... 52
11 – Troubleshooting.............................. 54
12 – Specifications .................................. 55
Changing the playback position
(scrubbing) .......................................................... 40
Mixing and outputting a multitrack
recording......................................................................41
Using the internal mixer ..................................41
Recording media and formats..............................55
Input and output.......................................................55
Analog audio input and output ...................55
Digital audio input and output.................... 56
Control input and output............................... 56
Audio performance................................................. 56
Other specifications................................................ 56
Dimensions .................................................................57
Block diagrams.......................................................... 58
Using the solo function....................................41
Playing a stereo track...............................................41
Setting the playback area ......................................42
Selecting a folder for the playback area
on the BROWSE screen............................................42
Setting the search speed .......................................42
Repeat playback........................................................42
7 – Connection with a computer............ 43
Copying files to a computer..................................43
Copying files from a computer ........................... 44
TASCAM DR-680MKIIDownload from Www.Somanuals.com. All Manuals Search And Download.
6
1 – Introduction
LCD with 128 x 64 pixel resolution and a backlight
USB2.0 port
•
•
•
Thank you very much for purchasing a TASCAM
DR-680MKII Portable Multitrack Recorder. Please read
this manual thoroughly before using the unit so that you
understand correct operating procedures and can use its
functions fully. We hope that you enjoy using this unit for
many years.
Please keep this manual so that you can read it at any time.
A digital copy of this manual can also be downloaded from
the TEAC Global Site (http://teac-global.com/).
USB cable included
Items included with the product
The DR-680MKII package contains the following items.
Take care when opening the package not to damage the
items. Keep the package materials for transportation in the
future.
Please contact the store where you purchased this unit
if any of these items are missing or have been damaged
during transportation.
Features
•
8-track recording with a resolution of up to 24-bit, 96
kHz (6 analog inputs with stereo mix, or 6 analog inputs
with digital stereo input)
•
Main unit..................................................................................×1
•
•
2-track recording resolution of up to 24-bit, 192 kHz
AC adaptor (GPE248-120200-Z).......................................×1
•
•
Recording/playback media: SD/SDHC/SDXC cards (up to
128 GB)
USB cable.................................................................................×1
•
•
Shoulder strap........................................................................×1
Owner’s manual (this document) ...................................×1
•
•
Recording/playback formats: BWF, WAV, MP3
Recording up to 4 tracks in MP3 format simultaneously
possible
The warranty is included at the end of English manual.
•
•
•
CAUTION
Sampling frequencies: 44.1 k, 48 k, 96 k and 192 kHz
Quantization rates: 16-bit, 24-bit
MP3 files can be recorded at resolutions of
96/128/192/320 kbps
6 balanced mic/line inputs (1–4 are XLR/TRS combo jacks
and 5–6 are TRS jacks)
Mic inputs can provide +48V phantom power
Always use the included AC adapter (GPE248-
120200-Z) with this unit. Never use the included AC
adapter with any other device. Doing so could cause
damage, fire or electric shock.
•
NOTE
•
•
The included AC adapter (GPE248-120200-Z) is
shipped with exchangeable outlet plugs. For details
Limiters on each input can automatically adjust their
levels appropriately if input levels are too high
•
Low-cut filters on each input are useful for reducing
low-frequency noise
Conventions used in this manual
•
•
•
•
6 unbalanced line outputs (RCA pin jacks)
S/PDIF and AES/EBU digital input and output (coaxial)
Supports MS mic decoding
Cascade function allows the transport of multiple
DR-680MKII units to be controlled by a single master unit
Pre-record function allows up to 2 seconds of input
before the start of recording to be captured
Auto-record function allows the unit to start recording
automatically when it detects a set sound input level
Mark function allows movement to specific playback
positions
Button lock function can be used to prevent
misoperation
Repeat playback function
Mixer for monitoring with level and pan controls
User can start a new take at any time without
interrupting recording
Take names can be based on a word set by the user or
the date
500-mW monaural output speaker built-in
50-mW + 50-mW headphones output
Operates on power from 8 AA batteries or an AC adaptor
(GPE248-120200-Z)
The following conventions are used in this manual.
•
“SD card”indicates SD, SDHC and SDXC memory cards.
•
When we refer to a button or connector or control on
the DR-680MKII, the typeface looks like this: MENU.
•
•
•
•
•
•
When we show messages, for example, that appear on
the screen, the typeface looks like this: BROWSE
.
Additional information is provided as necessary in tips,
notes and cautions
TIP
These are tips about how to use the unit.
NOTE
•
•
•
These include additional explanations and special
cases.
CAUTION
•
Failure to follow these instructions could result in
injury, equipment damage or lost data, for example.
•
•
•
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-680
7
1 – Introduction
Intellectual property rights
This product is designed to help you record and
reproduce sound works to which you own the
copyright, or where you have obtained permission
from the copyright holder or the rightful licensor.
Unless you own the copyright, or have obtained the
appropriate permission from the copyright holder
or the rightful licensor, your unauthorized recording,
reproduction or distribution thereof may result in
severe criminal penalties under copyright laws and
international copyright treaties. If you are uncertain
about your rights, contact your legal advisor. Under no
circumstances will TEAC Corporation be responsible
for the consequences of any illegal copying performed
using the recorder.
•
TASCAM is a trademark of TEAC Corporation, registered
in the U.S. and other countries.
•
SDXC Logo is a trademark of SD-3C, LLC.
•
Microsoft and Windows are either registered trademarks
or trademarks of Microsoft Corporation in the United
States and/or other countries.
•
•
Apple, Mac OS and Mac OS X are trademarks of Apple
Inc.
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
About SD cards
Supply of this product does not convey a license nor
imply any right to distribute MPEG Layer-3 compliant
content created with this product in revenue-generating
broadcast systems (terrestrial, satellite, cable and/or
other distribution channels), streaming applications (via
Internet, intranets and/or other networks), other content
distribution systems (pay-audio or audio-on-demand
applications and the like) or on physical media (compact
discs, digital versatile discs, semiconductor chips, hard
drives, memory cards and the like). An independent
license for such use is required. For details, please visit
This unit uses SD cards for recording and playback.
64MB–2GB SD cards, 4–32GB SDHC cards and 48–128GB
SDXC cards can be used.
A list of SD cards that have been tested with this unit can
be found on the TEAC Global Site (http://teac-global.com/).
Use of cards that have not been verified for use with this
unit could result in the unit not functioning properly.
Precautions for use
SD cards are delicate media. In order to avoid damaging a
card or the card slot, please take the following precautions
when handling them.
•
Other company names, product names and logos in this
document are the trademarks or registered trademarks
of their respective owners.
•
•
•
•
•
•
Do not leave in extremely hot or cold places.
Do not leave them in extremely humid places.
Do not let them get wet.
Do not put things on top of them or twist them.
Do not hit them.
Do not remove or insert a card during recording,
playback, data transmission or other access.
When transporting a memory card, put it into a case, for
example.
Any data, including, but not limited to information,
described herein are intended only as illustrations of
such data and/or information and not as the specifi-
cations for such data and/or information. TEAC Corpo-
ration disclaims any warranty that any use of such data
and/or information shall be free from infringement
of any third party’s intellectual property rights or
other proprietary rights, and further, assumes no
liability of whatsoever nature in the event of any such
infringement, or arising from or connected with or
related to the use of such data and/or information.
•
TASCAM DR-680MKIIDownload from Www.Somanuals.com. All Manuals Search And Download.
8
1 – Introduction
Precautions for placement and use
•
The environmental temperature operating range of this
unit is 0–40°C (32–104°F).
•
Do not install this unit in the following types of locations.
Doing so could degrade the sound quality and/or cause
malfunctions.
Places with significant vibrations
Near windows or other places exposed to direct
sunlight
Near heaters or other extremely hot places
Extremely cold places
Places with bad ventilation or high humidity
Very dusty locations
Places exposed directly to rain or other water
•
•
Do not place this unit on top of a power amplifier or
other device that generates heat.
If this unit is placed near a power amplifier or other
device with a large transformer, it could cause a hum. If
this occurs, increase the distance between this unit and
the other device.
•
•
This unit could cause color irregularities on a TV screen
or noise from a radio if used nearby. If this occurs, use
this unit farther away.
This unit might produce noise if a mobile phone or other
wireless device is used nearby to make calls or send
or receive signals. If this occurs, increase the distance
between this unit and those devices or turn them off.
•
•
To enable good heat dissipation, do not place anything
on top of this unit.
Do not place this unit on top of a power amplifier or
other device that generates heat.
Beware of condensation
If the unit is moved from a cold to a warm place, or used
after a sudden temperature change, there is a danger of
condensation; vapor in the air could condense on the
internal mechanism, making correct operation impossible.
To prevent this, or if this occurs, let the unit sit for one or
two hours at the new room temperature before using.
Cleaning the unit
Use a dry soft cloth to wipe the unit clean. Do not clean the
unit with a chemically treated cloth or substances such as
thinner and alcohol because they might cause damage to
the surface of the unit.
User registration
Customers in the USA, please visit the TASCAM website
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-680
9
2 – Names and Functions of Parts
Top panel
CAUTION
•
1 Built-in monaural speaker
Use this built-in speaker for monitoring. Use the
PHONES knob to adjust the volume.
Do not connect or disconnect mics when a PHANTOM
switch is set to ON. Doing so could cause a loud
noise and might damage this unit and connected
equipment.
Set the PHANTOM switch to ON only when using a
condenser microphone that requires phantom power.
Turning phantom power on when a dynamic mic or
other mic that does not require it is connected could
damage this unit and connected equipment.
Sound will not be output from the speaker in the
following conditions.
•
o
o
When headphones are connected
When SPEAKER output is set to OFF on the GENERAL
page
2 INPUT switches
•
•
Use these to set the inputs to LINE or MIC.
When using condenser mics that require phantom
power and dynamic mics together, be sure to use
balanced dynamic mics. Unbalanced dynamic mics
cannot be used when phantom power is enabled.
Supplying phantom power to some ribbon mics will
break them. If you are unsure, do not supply phantom
power to a ribbon mic.
3 HOLD switch
Slide this in the direction of the arrow to disable the
STANDBY/ON button to prevent the power from
accidentally being cut.
4 MIC GAIN switches
Use these to adjust the gain of the mic inputs.
7 MULTI/STEREO button
Press to select whether the stereo track or the multi-
track (6-track) is played back.
5 STANDBY/ON button
Press this to switch the unit power between ON and
STANDBY.
6 PHANTOM switches
Use these to turn phantom power ON or OFF for input
pairs 1/2, 3/4 and 5/6.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
10
2 – Names and Functions of Parts
8 MENU button
w Ô[Â] button
Press this button when the Home Screen is open to
Press this button during playback or when stopped in
the middle of a take to return to the beginning of the
current take.
Press when stopped at the beginning of the take to
skip to the beginning of the previous take.
Press and hold to search backwards.
9 DATA wheel
Use this to select items and change values on various
settings screens.
When the Home Screen is open, use the DATA wheel to
e [¯] button
move the playback position in the take.
Press this button during playback or when stopped to
skip to the beginning of the next take.
0 ENTER/MARK button
Press and hold to search forward.
Use this to confirm selections, advance to the next level
in a menu and respond “YES”to confirmation pop-up
messages on various settings screens.
r STOP button
Press to stop recording and playback and locate the
transport to the beginning of the current take.
q MARK (Â/¯) buttons
Use these on various settings screens to move the
cursor left and right.
Press to end recording standby.
t PLAY/PAUSE button
On the BROWSEscreen, use these to move up and
down levels.
Use MARK (Â) button to respond “NO”to confir-
mation pop-up messages on various settings screens
or to cancel the current operation.
Press when stopped or paused to start playback.
Press during playback to pause at that position.
Front panel
While pressing and holding this button, turn the
VALUE/MARK knob on the front of the unit to adjust
the display contrast.
y PHONES jack and knob
Use this standard stereo phone jack to connect
headphones. Use the PHONES knob to adjust the
headphones and speaker output level.
p FUNCTION button
When the Home Screen is open, press to open the
Functions Screen.
u Display
This shows a variety of information related to the
operation of the unit.
a MIX PAN button
Press to open the PANsettings screen. Press when the
PANsettings screen is open to close it and return to the
Home Screen.
i MENU button
Press this button when the Home Screen is open to
open the MENUscreen.
s VALUE/MARK knob
o HOME/DISPLAY button
Use this to change the value of the selected item on
the TRIM, LEVELand PANsettings screens.
Press when any screen other than the Home Screen is
open to return to the Home Screen.
On the Functions Screen, use this to select function
items, and press the knob to turn each function item
ON or OFF.
Change the counter display mode.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
11
2 – Names and Functions of Parts
Turn this knob while pressing the HOME/DISPLAY
button on the front panel to adjust the display
contrast.
When the MENUscreen is open, this dial can be used
for the same functions as the DATA wheel and pressing
this dial has the same function as the ENTER/MARK
button.
Press this button when recording to end the current
take and continue recording a new take without pause.
g REC TRIM button
Press to open the input TRIMsettings screen.
When the input TRIMsettings screen is open, press to
close it and open the Home Screen.
When the Home Screen is open, press to set a mark.
When the Home Screen is open, turn to skip to a mark.
h MIX LEVEL button
Press to open the LEVELsettings screen.
Press when the LEVELsettings screen is open to close
it and return to the Home Screen.
When the MENUscreen is open, press to move the
cursor left or right.
When the MENUscreen is open, turn to move the cursor
j Channel number buttons (1–6 buttons)
Use these to select tracks on the TRIM, LEVELand PAN
settings screens.
or change a setting value.
d PAUSE button and indicator
Press when stopped or recording to start recording
standby. The indicator lights when in recording
standby.
Press when in recording standby to arm/disarm that
track for recording.
On the Functions Screen, press to turn the selected
function ON or OFF for that track.
Press and hold to enable/disable solo monitoring of
that track.
Press when in recording standby to stop recording
standby.
NOTE
k MIX [LOCK] button
The PAUSE button on the front panel functions only
when recording. Use the PLAY/PAUSE button on the top
of the unit to pause playback.
When the LEVELscreen is open, this selects the stereo
track as the track to be controlled. Press and hold this
button to engage or disengage the lock function,
which disables the use of other buttons.
f REC button and indicator
Press when stopped or in recording standby to start
recording. The indicator lights when recording or in
recording standby.
Left side panel
being supplied, that device and this unit could be
damaged.
When using a condenser microphone, before
connecting to and disconnecting from a MIC/LINE
INPUTS jack, confirm that the phantom power for that
jack is OFF. If you connect or disconnect a mic while
phantom power is being supplied, that mic and this
unit could be damaged.
Do not connect an unbalanced dynamic mic to an XLR
connector when phantom power is being supplied.
Doing so could damage that mic and this unit.
l MIC/LINE INPUTS (XLR/TRS) jacks
These are balanced analog XLR/TRS combo jacks for
microphone and line level inputs (1: GND 2: HOT 3:
COLD, Tip: HOT Ring: COLD Sleeve: GND).
•
; MIC/LINE INPUTS (TRS) jacks
These are balanced analog TRS jacks for microphone
and line level inputs (Tip: HOT Ring: COLD Sleeve:
GND).
•
CAUTION
•
Confirm that phantom power is OFF before connecting
a line level device to a MIC/LINE INPUTS jack. If you
connect a line level device while phantom power is
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
12
2 – Names and Functions of Parts
Right side panel
z LINE OUTPUTS jacks
b SD card slot/USB port cover
These RCA pin jacks are unbalanced analog output
jacks. During the playback of multitrack files, the sound
previously recorded on each track is output from these
jacks.
During recording, the sound recorded to each track is
output from these jacks.
n Cord holder
Secure the cord of the included AC adaptor (GPE248-
120200-Z) with this holder to prevent the plug from
being disconnected accidentally.
m Kensington security slot
During the playback of the multi-track, according to
the unit setting, the stereo signal mixed by the internal
mixer can be output from output jacks 1/2, 3/4 or 5/6.
During the playback of a stereo track, the sound of the
stereo track is output through output jacks 1/2, 3/4 or
5/6.
x DIGITAL/SYNC IN jack
This is a digital input jack. The signal input through this
jack can be recorded to tracks 5 and 6 or the stereo
track. The unit automatically determines whether
the input signal is S/PDIF (IEC60958-3) or AES3-2003/
IEC60958-4 (AES/EBU), which are both supported.
Transmission occurs at double speed when the
sampling frequency is 96 kHz and at quad speed when
192 kHz.
When linking two of these units using the cascade
function, connect the DIGITAL/SYNC OUT jack of the
other DR-680MKII to this jack.
, SD card slot
Insert SD cards here.
. USB port
Connect this unit with a computer using a USB2.0
cable. The computer will recognize this unit as a mass
storage device. No driver software is necessary.
c DIGITAL/SYNC OUT jack
The stereo signal mixed by the internal mixer is output
from this jack.
Audio files can be transferred between an SD card in
this unit and a computer by the USB connection.
According to the unit setting, the signal is output in S/
PDIF (IEC60958-3) or AES3-2003/IEC60958-4 (AES/EBU)
format.
Transmission occurs at double speed when the
sampling frequency is 96 kHz and at quad speed when
192 kHz.
When linking two of these units using the cascade
function, connect the DIGITAL/SYNC IN jack of the
other DR-680MKII to this jack.
v DC IN 12V jack
Connect the included AC adaptor (GPE248-120200-Z),
which matches the power specifications of this unit.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
13
2 – Names and Functions of Parts
Bottom panel
/ Hook for the shoulder strap
@ Battery compartment cover
Attach the included shoulder strap here.
! Stand
Use this stand to raise the front of the unit when
operating it on a flat surface.
# Battery compartment
Install batteries (8 AA) for powering the unit in this
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
14
2 – Names and Functions of Parts
5 Level meters
Home Screen
These show the levels of tracks 1–6 and the stereo
track.
When recording, if stereo track recording is ON and the
stereo track recording source is set to DIGITAL IN, the
stereo track meters become the DIGITAL IN input level
meters.
During playback of a multitrack file, the playback levels
of each track are shown.
When recording, the recording levels of each track are
shown.
When recording, if a signal is distorted at the input
stage, the area beneath its meter is highlighted.
If a recording level exceeds 2.0 dB below the maximum
level, a mark appears at the top of its meter, indicating
an overload.
1 Take name
When stopped or during playback, the name of the
currently loaded take is shown.
When recording or in recording standby, the name of
the take being recorded is shown.
Up to 11 characters are shown. Longer names are
scrolled.
2 Recorder operation status
Ch2: Signal is distorted at the input stage
Ch4: Recording level exceeds 2.0dB less than the
maximum level.
During stereo track playback, the meters for tracks 1
and 2 function as the L and R meters.
The operation status of the recorder is shown with one
of the following icons.
:
:
Stopped
Playing back
: Paused
When a track is armed for recording, “º”appears
: Searching forward
: Searching backwards
: Recording
: Recording standby
: Skip forward
: Skip backward
beneath its meter.
When a track is soloed, “ ”appears beneath its meter.
NOTE
If a track is both armed for recording and soloed, only
“
” appears beneath its meter.
6 Time (hours: minutes: seconds)
During playback, the elapsed playback time of the take
is shown.
3 Repeat icon
When the repeat function is ON, the repeat icon
appears.
Press the HOME/DISPLAY button on the front panel
to show the remaining time of the take as a negative
number.
When recording, the elapsed recording time of the take
is shown.
Press the HOME/DISPLAY button on the front panel
to show the remaining available recording time for the
take.
4 Power supply status
When operating on battery power, a battery icon
appears.
Depending on the amount of remaining battery power,
a number of bars appear (
When the battery charge is very low, the last bar disap-
pears, the
soon change to standby.
When using the included AC adaptor (GPE248-
120200-Z), the
,
or
).
icon blinks, and the unit’s power will
7 Playback position
This bar shows the current playback position during
playback or the amount of remaining time available for
recording during recording. As recording or playback
progresses, the bar darkens from the left.
icon appears.
NOTE
Even before the batteries lose their charge, a “Battery
Low” warning pop-up message might appear if you try
to start recording or conduct another operation that
requires considerable power.
8 Mark information
The mark number and the total number of marks in the
current take are shown.
During playback, the number of the mark that is before
and closest to the current position is shown.
When recording, the last added mark number is shown.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
15
2 – Names and Functions of Parts
9 File type indicator
Menu structure
When stopped or during playback, the file type of the
currently loaded take is shown.
When you press the MENU button on the top or front of
the unit, the GENERALmenu page will open.
When recording or in recording standby, the file type of
the take being recorded is shown.
: BWF
: WAV
: MP3
0 Sampling frequency indicator
When stopped or during playback, the sampling
frequency of the currently loaded take is shown.
When recording or in recording standby, the sampling
frequency of the take being recorded is shown.
The MENU screen has 8 pages organized by types of menu
items.
GENERAL page
REC page
AUTO REC page
LOW CUT page
I/O page
: 44.1 kHz
: 48 kHz
: 96 kHz
: 192 kHz
PLAY page
q LOCK indicator
CARD page
SYSTEM page
The menu items are as follows.
When the lock function for the front panel and/or top
panel buttons is ON, the
indicator appears.
w STEREO indicator
Menu item
GENERAL page
BROWSE
Function
Reference
When a stereo track is being played, the
indicator appears. During stereo track playback, the
meters for tracks 1 and 2 function as the L and R
meters.
Open BROWSE screen
Set the built-in speaker
SPEAKER
e SOLO indicator
REC page
When a track has been soloed, the
indicator
Set recording file
format
appears. An icon appears beneath the meter of the
currently soloed track.
FORMAT
SAMPLE
DUAL REC
FILE
r Quantization/bit-rate indicator
When stopped or during playback, the quantization/
bit-rate of the currently loaded take is shown.
When recording or in recording standby, the quanti-
zation/bit-rate of the take being recorded is shown.
When the take being recorded or played is an MP3, its
bit rate is shown.
TRACK
Set recording track
Set stereo track
recording
Set recording after
recording pauses
Set take name format
ST REC
PAUSE
BWF/WAV
NAME
: 16-bit
: 24-bit
Reset take name
numbering
TAKE NO. INIT
AUTO REC page
LEVEL
MP3
: 96 kbps (48 kbps)
: 128 kbps (64 kbps)
: 192 kbps (96 kbps)
: 320 kbps (160 kbps)
Set automatic recording
function
SILENT CUT
Set silence cutting
function
SILENT DELAY
Set automatic mark
function
NOTE
AUTO MARK
The bit rate in parentheses is for when recording a
monaural take.
LOW CUT page
FREQUENCY
I/O page
Set low cut filter
Set the recording
source for tracks 5
and 6
INPUT 5/6
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
16
2 – Names and Functions of Parts
Menu item
LINE OUT
Function
Reference
Using menus
Set analog output
Set digital output
In this example, we show how to change the sampling
frequency.
DIGITAL OUT
PLAY page
AREA
1. Press the MENU button on the top or front of the unit
Set playback area
Set search speed
to open the GENERALpage of the MENUscreen.
SEARCH SPEED
CARD page
Show SD card infor-
mation
Format SD card
INFORMATION
FORMAT
SYSTEM page
2. Press the MENU button to open the menu page.
Set automatic powering
off
Set display backlight
3. Turn the DATA wheel on the top or the VALUE/MARK
knob on the front of the unit to select (highlight) a
setting item.
AUTO OFF
BACKLIGHT
CASCADE
LOCK MODE
BATTERY
Set lock function
Set battery type
INITIALIZE
View system infor-
INFORMATION
DATE/TIME
4. Press the ENTER/MARK button on the top or the
VALUE/MARK knob on the front to move the cursor to
the setting value.
mation
Set date and time
NOTE
•
When recording or in recording standby, pressing a
MENU button will not open the MENU screen.
•
The settings for all menu items are retained even when
the unit is turned off.
5. Turn the DATA wheel on the top or the VALUE/MARK
knob on the front of the unit to change the setting.
6. To set another item on the same screen, press the
MARK (.) button on the top of the unit. This
enables setting item selection again. Turn the DATA
wheel on the top or the VALUE/MARK knob on the
front of the unit to select (highlight) the desired setting
item.
7. Repeat steps 4–6 as necessary to set other items.
8. Press the HOME/DISP button on the front of the unit
to return to the Home Screen.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
17
2 – Names and Functions of Parts
Operation basics
Functions Screen
Use the following controls to operate the various settings
screens.
When the Home Screen is open, press the FUNCTION
button to open the Functions Screen.
MENU button
Press to open the MENUscreen when it is not already open.
This unit has two of these buttons — one on its top and
one on its front.
DATA wheel
Use to select items and to change values.
You can also use the VALUE/MARK knob instead for the
same functions.
On the Functions Screen, you can view and activate the
following items.
Repeat
Pre-record
Auto-record
DIN/MIX monitor
Limiter
ENTER/MARK button
Press to confirm the selection of a setting item, and to
select “YES”on a confirmation pop-up message.
You can also press the VALUE/MARK knob instead for the
same function.
Low-cut filter
1. When the Home Screen is open, press the FUNCTION
MARK (¯) button
Press to move the cursor right in a settings screen and to
open a folder on the BROWSEscreen.
button to open the Functions Screen.
2. Use the VALUE/MARK knob to move the cursor to
select the item to set.
3. Press the VALUE/MARK knob.
MARK (Â) button
When selecting LIMITERor LOWCUT, press the VALUE/
MARK knob or channel number (1–6) buttons.
Press to move the cursor left in a settings screen and to
close a folder on the BROWSEscreen.
4. When you have finished making the settings, press the
Press to select “NO”on a confirmation pop-up message.
HOME/DISP button to return to the Home Screen.
HOME/DISP button
When a settings screen is open, press the HOME/DISP
button to return to the Home Screen.
Repeat activation
Use the REPEATitem to turn loop playback ON or OFF. The
default value is OFF.
: Repeat playback ON
: Repeat playback OFF
Pre-record activation
Use the PRE.RECitem to turn the pre-record function ON
or OFF. The default value is OFF.
: Pre-record ON
: Pre-record OFF
Auto-record activation
Use the A.RECitem to turn the auto-record function ON or
OFF. The default value is OFF.
: Auto-record function ON
: Auto-record function OFF
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
18
2 – Names and Functions of Parts
DIN/MIX monitor settings
When the ST RECitem on the RECpage of the MENU
screen is set to DIN, the signal to be monitored can be
selected. Press the VALUE/MARK knob to select DIN MON
or MIX MON
.
The default value is MIX MON
.
: Set to monitor the stereo mix
: Set to monitor the digital input
NOTE
When the ST RECitem on the RECpage is set to
MIX, this setting is fixed to MIX MON, and it cannot be
changed to DIN MON
.
Limiter activation
Use the LIMITERitem to turn the limiter function ON or
OFF for each input independently.
The limiter for an input is ON when its number appears
light on a dark background. The default value is OFF for all
inputs.
Press the VALUE/MARK knob to turn the limiter ON or OFF
for all inputs at the same time.
Press the channel number (1–6) buttons to turn the limiter
ON or OFF for each input independently.
If the limiter has been turned ON for one or more inputs,
the LIMITERindicator appears with a dark background.
: Limiter ON for all inputs
: Limiter ON for input 1
: Limiter OFF for all inputs
Low-cut filter activation
Use the LOWCUTitem to turn the low-cut filter function
ON or OFF for each input independently.
The low-cut filter for an input is ON when its number
appears light on a dark background. The default value is
OFF for all inputs.
Press the VALUE/MARK knob to turn the low-cut filter ON
or OFF for all inputs at the same time.
Press the channel number (1–6) buttons to turn the
low-cut filter ON or OFF for each input independently.
If the low-cut filter has been turned ON for one or more
inputs, the LOWCUTindicator appears with a dark
background.
Low-cut filter ON for all inputs
Low-cut filter function ON for
input 1
:
:
Low-cut filter OFF for all inputs
:
NOTE
You can set the cut-off frequency with the FREQUENCY
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
19
3 – Preparations
on AA batteries (NiMH rechargeable or alkaline), the
operation time will be greatly shortened. If you need
to operate the unit for a long time, use the included
GPE248-120200-Z AC adaptor.
Powering the unit
About the power supply
This unit can be powered by 8 AA batteries or the included
GPE248-120200-Z AC adaptor, which matches the power
specifications of this unit.
Using the AC adaptor
As shown in the figure, connect the included GPE248-
120200-Z AC adaptor, which conforms to the specifications
of this unit, to the DC IN 12V jack.
This unit can use alkaline, Ni-MH or lithium AA batteries.
AC outlet
Using AA batteries
Slide off the battery compartment cover on the bottom
panel of this unit, insert 8 AA batteries into the battery
compartment according to the ¥/^ indications, and
close the compartment cover again.
DC plug
A hook (cord holder) to fix the cord of the AC adaptor is on
the right side panel. Wrap the cord around the hook when
connecting it to prevent it from being disconnected during
use.
When using AA batteries, set the battery type so that the
unit can accurately display the remaining battery charge
and determine the necessary minimum remaining charge
50.)
CAUTION
Use only the included GPE248-120200-Z AC adaptor,
which conforms to the specifications of this unit.
Use of an adaptor other than this model could cause
malfunction, fire or electric shock.
CAUTION
•
•
Manganese AA batteries cannot be used.
NOTE
•
This unit cannot recharge AA nickel-metal hydride
(NiMH) batteries. Use a commercially-available
battery recharger to recharge NiMH batteries.
If power is available from both batteries and the AC
adaptor, the power is supplied by the AC adaptor.
•
The AC adapter for the unit includes two types of outlet
plugs. Attach the type of plug that matches the power
outlet that you are using.
NOTE
A great amount of power is required to provide
phantom power to a condenser microphone. If you
use a condenser microphone while running the unit
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
20
3 – Preparations
Changing the outlet plug
Putting the unit into standby
When the power is ON, press and hold the STANDBY/ON
button until the following shutdown screen appears.
3
2
5
$
%
4
1
After the unit completes shutting down, the unit’s power is
set to standby.
1 Move the latch on the AC adapter in the direction
CAUTION
of the arrow.
Always use the STANDBY/ON button to put the unit
power into standby. When the power is ON, if you
remove the batteries or disconnect the power cord
when using the GPE248-120200-Z AC adaptor, all
recording data and settings, for example, are lost and
such data cannot be recovered.
2 Pull off the outlet plug.
3 Replace it with the other outlet plug (A or B).
4 Move the latch on the AC adapter in the direction
of the arrow again.
5 Attach the outlet plug to the AC adapter.
This completes changing the outlet plug.
Inserting and removing SD cards
After changing the outlet plug, confirm that is not
loose or crooked and that everything is normal
before plugging it into an outlet
64MB–2GB SD cards, 4–32GB SDHC cards and 48–128GB
SDXC cards can be used.
CAUTION
A list of SD cards that have been verified for use with this
unit can be found on the TEAC Global Site
(http://teac-global.com/).
Do not use the adapter if there is anything abnormal
about the plug after changing it. Use when the plug is
abnormal could cause fire or electric shock. Contact
the retailer where you purchased the unit or a TEAC
service center (on the back cover) to request repair.
Inserting an SD card
1. Open the SD card slot cover on the right side panel of
the unit.
2. Insert the SD card in the direction shown in the illus-
tration until it clicks into place.
Turning the power on and putting
the unit into standby
Turning the power on
When the power is in standby, press and hold the
STANDBY/ON button until the startup screen with
TASCAM DR-680MKIIappears. The unit starts up and the
Home Screen opens.
CAUTION
Do not remove or insert an SD card until the Home
Screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
21
3 – Preparations
Ejecting an SD card
Card write-protection
SD cards have lock (write-protection) switches.
CAUTION
•
Do not remove the SD card from the unit during
recording, playback or at other times when it is being
accessed.
•
•
•
Do not remove the SD card from the unit when it is
connected to a computer by USB.
SD cards that meet SD, SDHC or SDXC standards can
be used with this unit.
A list of SD cards that have been confirmed to work
with this unit can be found on the TEAC Global Site
(http://teac-global.com/).
Writing possible
Writing not possible
Slide the switch in the direction of the Lock arrow to
prevent the recording and editing of files on the card. To
record, erase or otherwise change files on a card, disable
the write-protection.
1. Open the SD card slot cover.
2. Push the SD card gently, and it will come out of the unit
slightly and can be pulled out.
Setting the date and time
This unit adds date and time information to recorded files
using its internal clock.
1. Press the MENU button to open the SYSTEMpage of
the MENUscreen.
2. Use the DATA wheel to select the DATE/TIMEmenu
item.
Preparing an SD card for use
An SD card must be formatted by this unit to be used with
the unit.
CAUTION
•
3. Press the ENTER/MARK button to open the DATE/
Formatting erases all data on the card.
TIMEscreen.
•
When formatting, use the included AC adaptor
(GPE248-120200-Z) or confirm that the remaining
battery charge is sufficient.
1. Confirm that the SD card is inserted and turn the
power ON.
2. If a new card or a card that has been formatted by
a device other than this unit has been inserted, the
following pop-up message appears.
4. Use the MARK (Â/¯) buttons to move the cursor
and use the DATA wheel to change the values.
5. Press the ENTER/MARK button to confirm and return
to the MENUscreen.
6. Press the MENU or HOME/DISP button to return to the
Home Screen.
NOTE
3. Press the ENTER/MARK button to start formatting.
You can add the date and time set here to the take
name. (See “Setting the name given to recording
4. When formatting is complete, the Home Screen opens.
You can reformat a card at any time with this unit. (See
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
22
3 – Preparations
sudden loud noises to occur, which might damage
your hearing or equipment.
To monitor with an external monitoring system (powered
monitor speakers or an amplifier and speakers), connect it
to the LINE OUTPUTS jack.
Turning the built-in speaker output
on and off
When shipped new from the factory, this unit's built-in
speaker output is set to on. To turn the built-in speaker
output off, set the SPEAKERitem on the GENERALpage
to off.
1. Press the MENU button to open the GENERALpage of
the MENUscreen.
2. Use the DATA wheel to select the SPEAKERitem, and
press the ENTER/MARK button.
Powered monitor speakers
or amplifier and speakers
3. Use the DATA wheel to select one of the following
settings.
Options: OFF, ON (default)
CAUTION
4. Press the MARK (.) button to return to item
Before using an external monitoring system, turn
the volume to minimum. Failure to do so could cause
sudden loud noises to occur, which might damage
your hearing or equipment.
selection on the MENUscreen.
5. Press the HOME/DISP button to return to the Home
Screen.
CAUTION
Adjusting the display contrast
Before using the built-in speaker, turn the PHONES
knob to the minimum volume. Failure to do so could
cause sudden loud noises to occur, which might
damage your hearing or equipment.
Turn the VALUE/MARK knob while pressing and holding
the HOME/DISPLAY button to adjust the display contrast.
NOTE
When headphones are connected, no sound is output
from the speaker.
Connecting monitoring equipment
To monitor with headphones, connect them to the
PHONES jack. Use the PHONES knob to adjust the
headphones volume.
Headphones
CAUTION
Before connecting headphones, turn the PHONES knob
to the minimum volume. Failure to do so could cause
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
23
4 – Recording
This unit can record in the following formats.
Recording settings
•
•
•
WAV/BWF (16/24-bit, 44.1 k/48 k/96 kHz)
6 tracks and a stereo mix
WAV/BWF (16/24-bit, 192 kHz)
2 tracks
MP3 (96/128/192/320 kbps, 44.1 k/48 kHz)
4 tracks
Setting the recording file format
You can set the recording file format (BWF/WAV/MP3) and
bit depth (BWF/WAV) or bit rate (MP3).
2 tracks and a stereo mix
NOTE
•
WAV format recordings have a higher audio quality
than MP3 format recordings.
Files and takes
•
BWF, which is the broadcast wave format, has the
same sound quality as the standard wave (WAV)
format.
With this unit, a group of audio files that are recorded at
the same time are collectively called a “take.”
Depending on the file recording mode setting, the files
included in the recorded take will be as follows.
Example 1: 6 tracks and a stereo track recorded
MONO format set: 6 mono WAV files and a stereo WAV
file
STEREO format set: 3 stereo WAV files of inputs pairs 1-2,
3-4 and 5-6 and a stereo WAV file of the mix
6ch format set: a 6-channel WAV file and a stereo WAV
file
•
•
•
•
MP3 format allows greater recording time than WAV
format.
With MP3 formats, higher bit rates record with better
audio quality.
For information about recording times, see “Recording
When the file format is set to MP3, the maximum
number of tracks is limited to 4 (4 mono, 2 stereo, or 2
mono and 1 stereo).
•
•
•
1. Press the MENU button to open the RECpage of the
MENUscreen.
Example 2: 4-track recording in MP3 format
•
•
2. Use the DATA wheel to select the FORMATitem, and
MONO format set: 4 mono MP3 files
STEREO format set: 2 stereo MP3 files
press the ENTER/MARK button.
An SD card in this unit can have up to 5000 files and folders
and 1000 takes.
When using a folder that contains a large number of files,
starting recording can take time and the beginnings of
recordings might be cut off. To prevent this, use a folder
that contains as few takes as possible or put the unit in
recording standby before recording. Moreover, if a folder
contains a large number of files, the same issues can occur
when starting a new take while continuing to record. (This
occurs when you press the REC button during recording
and automatically if the maximum file size is exceeded. For
3. Use the DATA wheel to select one of the following
options:
BWF-16bit
,
BWF-24bit
,
WAV-16bit(default value),
WAV-24bit
MP3-96kbps
MP3-128kbps
MP3-192kbps, or
MP3-320kbps
,
,
NOTE
,
•
You should use a folder that contains as few takes
.
as possible when planning to create new takes while
recording.
To avoid these problems, the maximum number of
takes in a folder is about 100.
4. Press the MARK (.) button to return to item
•
selection on the MENUscreen.
5. Press the HOME/DISP button to return to the Home
Screen.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
24
4 – Recording
Setting the sampling frequency
Stereo track recording settings
You can set the sampling frequency and record BWF and
WAV files at 44.1, 48, 96 or 192 kHz.
You can set what is recorded on the stereo track.
1. Press the MENU button to open the RECpage of the
1. Press the MENU button to open the RECpage of the
MENUscreen.
MENUscreen.
2. Use the DATA wheel to select the STRECitem, and
2. Use the DATA wheel to select the SAMPLEitem, and
press the ENTER/MARK button.
press the ENTER/MARK button.
3. Use the DATA wheel to select one of the following
3. Use the DATA wheel to select one of the following
options.
options: 44.1kHz(default value), 48kHz, 96kHz, or
MIX(default): Record a mix of the 6 inputs on the
192kHz
.
stereo track.
NOTE
DIN:
Record the signal from the DIGITAL/
SYNC IN input jack on the stereo track.
When the file format is MP3, 96 kHz and 192 kHz
cannot be selected.
4. Press the MARK (.) button to return to item
4. Press the MARK (.) button to return to item
selection on the MENUscreen.
selection on the MENUscreen.
5. Press the HOME/DISP button to return to the Home
5. Press the HOME/DISP button to return to the Home
Screen.
Screen.
Setting the file recording mode
The file recording mode can be set to a monaural file, a
stereo file or a 6-channel file.
Arming and disarming tracks for
recording
Tracks can be armed and disarmed for recording from the
MENUscreen.
1. Press the MENU button to open the RECpage of the
MENUscreen.
1. Press the MENU button to open the RECpage of the
2. Use the DATA wheel to select the FILEitem, and press
MENUscreen.
the ENTER/MARK button.
2. Use the DATA wheel to select (highlight) the TRACK
item, and press the ENTER/MARK button.
3. Use the DATA wheel to select one of the following
options: MONO, STEREO(default value), or 6ch
.
3. Use the channel number (1–6) buttons on the front
panel to arm/disarm recording for the corresponding
tracks. When a track is armed for recording, its track
number appears light on a dark background.
NOTE
•
When set to MONO, a mono file is created for each
recorded track. When set to STEREO, a stereo file is
created for each pair of tracks (1-2, 3-4 and 5-6). When
set to 6ch, one 6-channel file is created for tracks 1-6.
•
•
6ch cannot be selected when the file format is set to
MP3 or the sampling frequency is set to 192 kHz.
When dual recording is enabled, only MONO can be
selected. (See “Enabling dual recording” on page
31.)
4. Press the MARK (.) button to return to item
selection on the MENUscreen.
•
Press the MARK (.) button to return to item
5. Press the HOME/DISP button to return to the Home
selection on the MENUscreen.
Screen.
4. Press the HOME/DISP button to return to the Home
Screen.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
25
4 – Recording
Creation of new takes when restarting
recording
Setting the name given to recording
takes
Set whether the unit continues recording to the same
take or begins a new take when restarting recording. This
setting determines the take recorded to when you press
the REC button again after having pressed the PAUSE
button to put the unit in recording standby.
Set whether take names are based on the date or one of
three names that have been created on the NAMEEDIT
screen.
1. Press the MENU button to open the RECpage of the
MENUscreen.
1. Press the MENU button to open the RECpage of the
2. Use the DATA wheel to select the NAMEitem, and press
MENUscreen.
the ENTER/MARK button.
2. Use the DATA wheel to select the PAUSEitem, and
press the ENTER/MARK button.
3. Use the DATA wheel to select one of the following
options.
3. Use the DATA wheel to select one of the following
DATE(default value): The take name is based on the
options.
date.
SAMETAKE(default value): Continue recording to the
same take.
USER1:
USER2:
USER3:
The take name is based on a user
word defined on the USERWORD
EDITscreen.
NEWTAKE
:
Record to a new take.
4. Press the MARK (.) button to return to item
The take name is based on a user
word defined on the USERWORD
EDITscreen.
selection on the MENUscreen.
5. Press the HOME/DISP button to return to the Home
Screen.
The take name is based on a user
word defined on the USERWORD
EDITscreen.
4. Press the MARK (.) button to return to item
selection on the MENUscreen.
5. Press the HOME/DISP button to return to the Home
Screen.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
26
4 – Recording
Editing the user take names
You can edit the user words used for take names on the
NAMEEDITscreen.
Resetting take name numbering
1. Press the MENU button to open the RECpage of the
MENUscreen.
1. Press the MENU button to open the RECpage of the
2. Use the DATA wheel to select the TAKE NO. INIT
MENUscreen.
item.
2. Use the DATA wheel to select the NAMEitem, and press
the ENTER/MARK button.
3. Press the ENTER/MARK button to open the confir-
mation pop-up message.
3. Press the MARK (¯) button again to open the USER
WORDedit screen.
4. Press the ENTER/MARK button again to reset the
number that follows the characters to “0000”. Press the
MARK button on the top of the unit to return to item
selection on the RECpage.
4. Use the DATA wheel to select the user word that you
want to edit, and press the ENTER/MARK button.
5. Press the HOME/DISP button to return to the Home
Screen.
Available recording time display
Available recording time varies according to the SD card
capacity and the file format, file mode and sampling
5. Use the following buttons to edit the user words.
Move the cursor.
Select characters.
Add a space at the cursor
position.
Erase the character at the
cursor position
MARK (Â/¯) buttons:
DATA wheel:
You can check the amount of time available for recording
using the inserted SD card on the Home Screen. When
recording or in recording standby press the HOME/
DISPLAY button to switch between showing the elapsed
recording time (of the current recording) and the
remaining available recording time. When the remaining
available recording time is shown, it appears as a negative
number.
, [/] button:
m [.] button:
6. When you have finished editing a user word, press the
ENTER/MARK button.
7. Press the HOME/DISP button to return to the Home
Screen.
Set the folder for saving takes
You can set the folder where recorded takes are saved. (See
takes are saved in the “PROJECT0000”folder that is
automatically created under the “MUSIC”folder.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
27
4 – Recording
Phantom power
This unit can supply +48 V phantom power to condenser
microphones.
Use the PHANTOM switches on the top panel to turn the
phantom power supply ON or OFF for mic input pairs 1/2,
3/4 and 5/6.
Connecting other equipment
Connect microphones and other external equipment as
shown in the figure below.
Microphones
CAUTION
•
Phantom power is also supplied to the TRS pins of
the MIC/LINE INPUTS Jack. If you connect a line level
device while phantom power is being supplied, that
device and this unit could be damaged.
Confirm that phantom power is OFF before connecting
a line level device to a MIC/LINE INPUTS jack. If you
connect a line level device while phantom power is
being supplied, that device and this unit could be
damaged.
Do not connect or disconnect mics when a PHANTOM
switch is set to ON. Doing so could cause a loud
noise and might damage this unit and connected
equipment.
Set the PHANTOM switch to ON only when using a
condenser microphone that requires phantom power.
Turning phantom power on when a dynamic mic or
other mic that does not require it is connected could
damage this unit and connected equipment.
Input settings
•
This unit has 6 analog mic/line inputs and a stereo digital
input.
6 tracks and a stereo track can be recorded for a total of 8
tracks.
The inputs recorded on the tracks are as follows.
•
•
Track
Input
Tracks 1/2
Tracks 3/4
Tracks 5/6
Analog inputs 1/2
Analog inputs 3/4
Analog inputs 5/6 or digital input
Stereo mix of inputs 1–6 or digital
input
Stereo track
Set the recording source for the stereo track on RECpage
•
•
When using condenser mics that require phantom
power and dynamic mics together, be sure to use
balanced dynamic mics. Unbalanced dynamic mics
cannot be used when phantom power is enabled .
Supplying phantom power to some ribbon mics will
break them. If you are unsure, do not supply phantom
power to a ribbon mic.
Setting the input sources
Use the INPUT switches on the top panel to set the type of
input for each track to either mic or line.
LINE: Set the switch to LINE when the line output jack of
an external device is connected to the analog input on this
unit.
MIC: Set this switch to MIC when a microphone is
connected to this unit.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
28
4 – Recording
or during playback. It cannot be turned ON/OFF
when record standby is caused by use of the Auto
Rec function or record standby is enabled during
recording.
Selecting the inputs for recording to
tracks 5 and 6
Tracks 5 and 6 can be used to record either analog mic/line
inputs or the digital input.
3. If a mic is connected, set the MIC GAIN switch for that
input to LOW.
1. Press the MENU button to open the I/Opage of the
MENUscreen.
2. Use the DATA wheel to select the INPUT5/6item, and
press the ENTER/MARK button.
3. Use the DATA wheel to select ANALOG(default value)
or DIGITAL
.
ANALOG: Record the signals of analog inputs 5
and 6 to tracks 5 and 6.
DIGITAL: Record the digital input signal to tracks
5 and 6.
NOTE
If an INPUT switch is set to LINE, the corresponding MIC
GAIN switch is disabled.
4. Press the REC TRIM button to open the TRIMscreen.
NOTE
If the ST REC item is set to DIN, this setting has no
effect. The unit will operate as though set to ANALOG.
Adjusting the input levels
1. Press the PAUSE button to enable recording standby.
The PAUSE and REC indicators light.
PAUSE indicator
REC indicator
5. Use this screen to set input levels. Use the channel
number (1–6) buttons to select the input channels that
you want to adjust.
NOTE
Multiple channels can be linked and controlled at the
2. Use the channel number (1–6) and MIX [LOCK]
buttons to turn the record function ON for tracks that
you want to record. When the record function is ON for
a track, an º appears under its meter on the display.
NOTE
•
If the file recording mode is set to STEREO, the record
function is turned ON and OFF for channels in pairs.
If the file recording mode is set to 6ch, the record
function cannot be turned ON and OFF for individual
channels.
•
The record function can only be turned ON/OFF when
record standby is enabled when the unit is stopped
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
29
4 – Recording
6. Use the VALUE/MARK knob to adjust the input levels
2. Press the REC button to start recording. During
recording, the REC indicator lights, and the elapsed
recording time or remaining recordable time appear on
the display.
in a range of 32 dB (default value: 0).
CAUTION
When recording with microphones, please pay
attention to the following points.
•
Adjust the input level so that distortion does not occur
at the input stage. If distortion does occur at the input
stage, the channel number to the left of the meter
on the TRIM screen is shown as a light number on a
dark background. In this case, the unit might record
distorted sound even if the overload indicator for the
meter has not appeared.
NOTE
You can also start recording by pressing the REC
button first without pushing the PAUSE button
beforehand.
3. Press the STOP button to stop recording.
•
When adjusting the input level, at first, set the MIC
GAIN switch to LOW and adjust the input level on the
TRIM screen. If the input level is still too low even when
the trim is set to maximum, set the MIC GAIN switch to
HIGH.
TIP
•
In addition to using the TRIM screen to adjust the
recording levels, try changing the orientation of the
microphones and their distances from the sources of
the sound. The orientation and distance of a micro-
phone also changes the sound quality.
Press the PAUSE button to pause recording. When
paused, you can press the REC button again to restart
recording.
•
You can use the limiter function to prevent distortion
when recording even when loud sounds are input. (See
7. Press the REC TRIM or HOME/DISP button to return to
the Home Screen.
Recording a take
NOTE
Before starting the following procedures, input selection
and level adjustment for each track should be completed,
and the Home Screen should be open.
You can set whether recording continues in the same
take or a new take is created when you start recording
again after pausing. (See “Creation of new takes when
1. Press the PAUSE button to start recording standby. The
PAUSE and REC indicators light.
PAUSE indicator
REC indicator
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
30
4 – Recording
Recording a stereo mix
Simultaneously recording two files
at different input levels (DUAL REC)
With this unit, in addition to recording up to 6 discrete
tracks from the 6 inputs, these inputs can also be mixed
internally and recorded as a stereo track.
Before starting the following procedures, input selection
and level adjustment for each track should be completed,
and the Home Screen should be open.
This recorder can simultaneously record a second
recording at a different input level along with the regular
recording. For example, when recording with microphones,
you can make an ordinary recording with the input level
set as high as possible and simultaneously record at a −12
dB lower input level for security.
1. Press the MIX LEVEL button to open the LEVEL
screen.
Two recorded takes will be saved: one at the ordinary
recording input level and another with a −12dB input level.
MIC/LINE INPUTS 1/3/5 are the three input jacks that can
be used for dual recording with this unit.
The audio recorded at the ordinary level will use mixer
channels 1/3/5 and be recorded to tracks 1/3/5.
The audio recorded at the reduced level will use mixer
channels 2/4/6 and be recorded to tracks 1/3/5 of a
different take.
2. On this screen you can adjust the mix levels of each
input channel and the recording level of the stereo
track. Use the channel number (1–6) and MIX [LOCK]
buttons to select the channels that you want to adjust.
NOTE
•
Files recorded when Dual Rec mode is selected will be
Mono files.
NOTE
Multiple channels can be linked and controlled at the
3. Use the VALUE/MARK knob to adjust each to a
suitable recording level in a range from 0–100 (default
value: 100).
•
Make the input level setting for the ordinary recording
in the usual manner. (See “Adjusting the input levels”
Enabling dual recording
NOTE
1. Press the MENU button to open the RECpage of the
Adjust the levels so that overload indicators do not
appear at the tops of the meters.
MENUscreen.
2. Use the DATA wheel to select the DUAL RECitem, and
4. Next, press the MIX PAN button to open the PAN
press the ENTER/MARK button.
screen.
3. Use the DATA wheel to select one of the following
5. On this screen you can adjust the pan (stereo position)
of each channel. Use the channel number (1–6)
settings.
buttons to select the channel that you want to adjust.
Options: OFF, ON (default)
4. Press the MARK (.) button to return to item
NOTE
selection on the MENUscreen.
Multiple channels can be linked and controlled at the
6. Use the VALUE/MARK knob to adjust each to a
suitable stereo position using values ranging from L10–
L1 (left) to C (center) and R1–R10 (right).
5. Press the HOME/DISP button to return to the Home
Screen.
NOTE
•
•
•
•
Stereo file and 6ch file modes cannot be selected.
MS mode will be canceled.
GANG settings will be canceled.
When recording starts, soloing of channels 2/4/6 will
be canceled.
(Odd number channels are set to L10 and even number
channels are set to R10 by default.)
NOTE
Adjust the pan settings of the channels so that the mix
is balanced as desired. You can check the balance with
the MIX meters at the far right.
7. When you have finished making the settings, press the
HOME/DISP button to return to the Home Screen.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
31
4 – Recording
Starting dual recording
Press the REC button to start dual recording.
When dual recording, “D”will appear for the dual channels
(2/4/6) on the Home Screen.
Automatically starting and pausing
recording (auto-record function)
If you turn the auto-record function ON, you can automat-
ically start, stop and pause recording in response to the
level of the input sound.
If an input level greater than the level set in advance is
detected on any input channel, recording starts.
In addition, the unit can automatically cut silent parts and
add marks at points where recording starts again.
NOTE
Dual recording take names
The levels of input on all channels must remain
below the set level for at least one second before the
auto-record function is activated.
Dual recording will create two files simultaneously.
The name of the second take created by dual recording has
Dadded to the take name of the ordinary recording.
Using the auto-record function
SCNO127_001
1. When the Home Screen is open, press the FUNCTION
button to open the Functions Screen.
SCN0127_001_D
2. Use the VALUE/MARK knob to move the cursor and
select the A.RECitem.
3. Press the VALUE/MARK knob to turn auto-recording
1: Set by the NAMEitem on the RECmenu page
2: Basic recording file number
ON or OFF.
If auto-recording has been turned ON, the A.REC
indicator appears with a dark background.
3: Dadded to dual recording take
Using the solo function
Press and hold one of the channel number (1–6) buttons
on the front panel to enable solo monitoring for that
channel.
4. When you have finished making the settings, press the
HOME/DISP button to return to the Home Screen.
Auto-record settings
1. Press the MENU button to open the AUTO RECpage
of the MENUscreen.
2. Use the DATA wheel to select the LEVELitem, and
press the ENTER/MARK button.
When solo monitoring, the
indicator appears
on the Home Screen, and the indicator appears for the
soloed channel.
3. Set the level at which the unit determines that a signal
is being input for starting and stopping automatic
recording. Use the DATA wheel to set the value to
To turn solo monitoring off, press and hold the corre-
–6dB, –12dB(default value), –24dB, or –48dB
.
sponding channel number (1–6) button again.
4. When you have finished making the settings, press the
HOME/DISP button to return to the Home Screen.
NOTE
5. Press the PAUSE button to enter recording standby.
When the input sound exceeds the level set by the
LEVELitem, the unit automatically starts recording.
Solo monitoring is only possible using the headphones
and built-in speaker.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
32
4 – Recording
Automatically cutting unnecessary
silences when recording (silent cut
function)
When recording, the unit can pause when it detects silence
for a certain amount of time, and then restart recording
when it detects an input signal again. Since this cuts
unnecessary silence during recording, space on the card
can be conserved.
Automatically adding marks at the
position where recording restarts
You can set whether a mark is added or a new take is
created whenever input higher than the set auto rec level
is detected after the input level has been below the auto
rec level for one second or more.
1. Set the A.RECitem on the Function Screen and
the LEVELitem on the AUTO RECmenu page as
described above.
1. Set the A.RECitem on the Function Screen and
the LEVELitem on the AUTO RECmenu page as
described above.
2. Use the DATA wheel to select the AUTOMARKitem, and
press the ENTER/MARK button.
3. Use the DATA wheel to set it to MARKor TAKE
.
2. Use the DATA wheel to select the SILENTCUTitem,
and press the ENTER/MARK button.
3. Use the DATA wheel to set it to ON(default value: OFF).
OFF(default): Auto mark function off
MARK: After the input level has been below the set
auto rec level for one second or more, when input
higher than the auto rec level is detected again, a mark
is added at that position. Recording continues in the
same take.
4. Press the MARK (Â) button to return to selecting
items.
5. Use the DATA wheel to select the SILENTDELAYitem,
and press the MARK (¯) button.
TAKE: After the input level has been below the set auto
rec level for one second or more, when input higher
than the auto rec level is detected again, recording
continues in a new take. After pausing because of
activation of the silent cut function, recording restarts
in a new take.
4. When you have finished making the settings, press the
6. Use the DATA wheel to set the silence that must be
detected before recording is paused between 1–5
seconds (default value: 1 seconds).
HOME/DISP button to return to the Home Screen.
5. Press the PAUSE button to start recording standby.
Depending on the setting, a mark is added or a new
take is created when recording starts automatically.
7. When you have finished making the settings, press the
HOME/DISP button to return to the Home Screen.
8. Press the PAUSE button to start recording standby.
When the input sound exceeds the level set in the
LEVELitem, recording starts automatically.
When the input sound level is below the level set in
the LEVELitem for a set number of seconds, recording
automatically pauses.
When the input sound exceeds the level set in the
LEVELitem again, recording restarts automatically.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
33
4 – Recording
Automatically incrementing tracks by
file size
When recording, if the size of the file reaches one of the
limits listed below, the unit stops recording the current
take and starts recording in a new take without inter-
rupting the recording.
Track incrementation
With this unit, the maximum recording file size is 2 GB.
If the file size reaches 2 GB while recording, the unit
automatically continues recording in a new take and stops
recording the current take.
WAV/BWF: When the file size reaches 2 GB
Manually incrementing tracks during
recording
MP3: When the file size reaches 2 GB or the recording time
reaches 24 hours
You can manually create a new take during recording at
any time.
Press the REC button during recording to create a new take
and continue recording.
CAUTION
•
If the total number of folders and files would exceed
5000, a new take cannot be created.
If the total number of takes would exceed 1000, a new
take cannot be created.
•
NOTE
Recording times are different for the same file size
depending on the file format and recording mode.
Using the limiter
NOTE
•
When a new take is created, the number at the end of
Turn the limiter function ON to make the unit automati-
cally adjust the input level to prevent distortion if the input
level is too loud.
the take name is increased by one.
•
You should use a folder that contains as few takes as
possible when creating new takes while recording or
when expecting to do so.
1. When the Home Screen is open, press the FUNCTION
button to open the Functions Screen.
•
The maximum number of takes in a folder is about
100.
2. Use the VALUE/MARK knob to move the cursor and
select the LIMITERmenu item.
3. Press the VALUE/MARK knob.
CAUTION
4. Press the VALUE/MARK knob to turn the limiter ON or
OFF for all inputs at the same time (default: all channels
off).
•
•
•
•
If the total number of folders and files would exceed
5000, a new take cannot be created.
If the total number of takes would exceed 1000, a new
take cannot be created.
A new take cannot be created if the recording time is
less than 4 seconds.
If the newly created take would have the same name
as an existing take, the numerical suffix is increased by
one as many times as necessary until a unique name
is created.
Press the channel number (1–6) buttons to turn the
limiter ON or OFF for each input independently.
If the limiter has been turned ON for one or more
inputs, the LIMITERindicator appears with a dark
background.
5. When you have finished making the settings, press the
HOME/DISP button to return to the Home Screen.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
34
4 – Recording
Using the low-cut filter
Using marks
Use the low-cut filter to reduce low-frequency noise. Set
the cut-off frequency to 40 Hz, 80 Hz or 120 Hz according
to the recording conditions.
Manually adding marks when recording
and during playback
Press the VALUE/MARK knob or ENTER/MARK button
when recording and during playback to add a mark at a
desired position.
Turning the low-cut filter on and off
1. When the Home Screen is open, press the FUNCTION
button to open the Functions Screen.
2. Use the VALUE/MARK knob to move the cursor and
select the LOWCUTmenu item.
3. Press the VALUE/MARK knob.
4. Press the VALUE/MARK knob to turn the low-cut filter
ON or OFF for all inputs at the same time (default: all
channels off).
The mark number is shown when you do this.
Press the channel number (1–6) buttons to turn the
low-cut filter ON or OFF for each input independently.
If the low-cut filter has been turned ON for one or more
inputs, the LOWCUTindicator appears with a dark
background.
NOTE
•
When a recording is paused and then restarted, a mark
is added at that point. Marks are numbered in each
take from 01–99, and the mark data is saved with each
take.
5. When you have finished making the settings, press the
•
HOME/DISP button to return to the Home Screen.
If you add a mark during playback, the mark is not
immediately saved in the file, but rather is saved when
playback stops. If you change the take using the m
[.] or , [/] button without stopping, the
addition of mark is not completed.
Setting the cut-off frequency of the
low-cut filter
1. Press the MENU button to open the LOW CUTpage of
Moving to a mark
the MENUscreen.
2. Use the DATA wheel to set the cut-off frequency to 40
When stopped or during playback, use the MARK
(.//) buttons to move to the positions of marks
added to the current state.
Hz, 80Hz(default value) or 120Hz
.
3. When you have finished making the settings, press the
HOME/DISP button to return to the Home Screen.
You can use these marks to index places where you might
want to resume playback.
NOTE
You cannot move to a mark in a different take.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
35
4 – Recording
Erasing marks
Press the ENTER/MARK button on the top of the unit to
delete a mark added at the current position.
Pre-recording
When the unit is in recording standby, the unit can record
up to two seconds before the start of recording and
include it in the recording.
1. When the Home Screen is open, press the FUNCTION
button to open the Functions Screen.
2. Use the VALUE/MARK knob to move the cursor and
select the PRE.RECmenu item.
3. Press the VALUE/MARK knob to turn pre-recording ON
or OFF.
If pre-recording has been turned ON, the PRE.REC
indicator appears with a dark background.
NOTE
If you erase a mark during playback, the mark is
not immediately erased, but rather is erased when
playback stops. If you change the take using the m
[.] or , [/] button without stopping, the
erasure of marks is not completed.
4. When you have finished making the settings, press the
HOME/DISP button to return to the Home Screen.
TIP
Used in combination with the auto-record function,
you can capture recordings without losing the initial
sound.
NOTE
If the unit has been in recording standby for less than
two seconds, only the amount of time that the unit has
been in standby can be recorded.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
36
4 – Recording
Recording times
Recording times (in hours and minutes) for different file formats and SD/SDHC/SDXC card capacities are shown in the
following table.
SD/SDHC/SDXC card capacity
WAV/BWF
Sampling
Number
of tracks
2
4
8
16
32
64
128
Bit length
16
frequency (kHz)
1:02
0:47
0:42
0:31
0:57
0:43
0:38
0:28
0:28
0:21
0:19
0:14
0:43
0:28
2:05
1:34
1:23
1:02
1:55
1:26
1:17
0:57
0:57
0:43
0:38
0:28
1:26
0:57
4:11
3:08
2:47
2:05
3:51
2:53
2:34
1:55
1:55
1:26
1:17
0:57
2:53
1:55
8:23
6:17
5:35
4:11
7:42
5:47
5:08
3:51
3:51
2:53
2:34
1:55
5:47
3:51
16:47
12:35
11:11
8:23
33:35
25:11
22:23
16:47
30:51
23:08
20:34
15:25
15:25
11:34
10:17
7:42
67:11
50:23
44:47
33:35
61:43
46:17
41:09
30:51
30:51
23:08
20:34
15:25
46:17
30:51
6
8
6
8
6
8
6
8
6
8
6
8
2
2
44.1
24
16
24
16
24
15:25
11:34
10:17
7:42
48
96
7:42
5:47
5:08
3:51
11:34
7:42
23:08
15:25
16
24
192
MP3
SD/SDHC/SDXC card capacity
Bitrate Number
(kbps) of tracks
2
4
8
16
32
64
128
96
128
192
320
23:08
17:21
11:34
6:56
46:17
34:43
23:08
13:53
92:35
69:26
46:17
27:46
185:00
138:00
92:35
370:00
277:00
185:00
111:00
740:00 1481:00
555:00 1111:00
4
370:00
222:00
740:00
444:00
55:33
•
•
The above recording times are estimates, and might differ according to the SD/SDHC/SDXC card.
The above recording times are not continuous recording times. They are total recording times for SD/SDHC/SDXC card
capacities.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
37
5 – Take and folder operations (BROWSE screen)
On the BROWSEscreen, you can view the contents of the
Take operations
MUSICFolder (take storage folder), which is where take
files are stored on the SD card.
To open the BROWSEscreen, press the MENU button on
Select the desired take on the BROWSEscreen and press
the ENTER/MARK button to open the pop-up window that
the top of the unit and open the GENERALmenu page.
is shown below.
Then, use the DATA wheel to select (highlight) BROWSE
,
and press the ENTER/MARK button.
Use the DATA wheel to select the desired item from the
following options, and press the ENTER/MARK button to
execute it.
The contents of the folder that contains the take that was
selected on the Home Screen before the BROWSEscreen
was opened appears on the display.
PLAY
Choose this to select the take, return to the Home Screen
and start playback of that take. If the playback area is set
to FOLDER, the folder that contains this take becomes the
playback area.
Navigating the BROWSE screen
On the BROWSEscreen, folders and takes appear in a
hierarchical structure much like they would appear on a
computer. On this unit, only one level of folders can be
created.
INFO
This shows information about the selected take.
•
Use the DATA wheel to select takes and folders.
•
When a folder is selected, press the MARK (¯) button
to show the contents of that folder.
•
•
When a taker folder is selected, press the MARK (Â)
button to close the currently open folder and show the
higher-level folder that contains it.
When a folder or take is selected, press the ENTER/
MARK button to open the pop-up menu.
Press the ENTER/MARK or MARK (Â) button again to
return to the BROWSEscreen.
DELETE
If you choose this, a pop-up message appears to confirm
that you want to delete the take. Press the ENTER/MARK
button to erase the take and return to the BROWSEscreen.
Icons on the BROWSE screen
Press the MARK (Â) button to cancel deletion and
The meanings of the icons that appear on the BROWSE
screen are as follows.
reopen the pop-up menu.
MUSIC folder (
)
The MUSICfolder is the highest-level folder (root folder)
shown on the BROWSEscreen.
Take (
This icon appears before the name of a recorded take.
Folder (
This icon shows a folder.
Open folder (
)
CANCEL
)
Press this to not conduct any operation on the selected
take.
)
The contents of this folder are currently shown on the
screen.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
38
5 – Take and folder operations (BROWSE screen)
REBUILD
Folder operations
A pop-up appears to confirm that you want to rebuild the
selected folder.
Select the desired folder on the BROWSEscreen, and press
the ENTER/MARK button to open the following pop-up
menu.
Rebuilding refreshes the take information inside the
selected folder, and recognizes files that are not contained
in takes as independent takes, making their playback
possible. Use this function after you have copied files to
the SD card from a computer, for example.
Press the ENTER/MARK button to rebuild the folder and
return to the BROWSEscreen.
Use the DATA wheel to select the desired item from the
following options, and press the ENTER/MARK button to
execute it.
SELECT
Returns to the Home Screen and selects the first take in
the folder. This folder becomes the new playback area
regardless of the previous playback area setting. New
recorded takes are saved in this folder.
Press the MARK (Â) button to cancel rebuilding and
reopen the pop-up menu.
Moreover, if file names have been added according to the
following rules, multiple files will automatically be regis-
tered as a single take. However, this does not mean that
their formats (WAV/BWF or MP3), sampling frequencies,
bit depths (for WAV/BWF files), bit rates (for MP3 files), file
types (mono or stereo) and file sizes will all be the same.
CREATE
A pop-up appears to confirm that you want to create a
new folder.
8
File naming rules (WAV/BWF example)
o
Mono file
XXXX_monoY.wav
XXXX_stY.wav
Press the ENTER/MARK button to create a new folder. New
o
Stereo file
recorded takes are saved in this folder.
Press the MARK (Â) button to cancel folder creation and
reopen the pop-up menu.
ALLDEL
1: Take name part (no more than 10 half-width alpha-
A pop-up appears to confirm that you want to delete all
the takes in the selected folder at once.
Press the ENTER/MARK button to erase the takes and
return to the BROWSEscreen. Press the MARK (Â)
button to cancel deletion and reopen the pop-up menu.
numeric characters)
2: File type (mono or stereo)
3: Track number (1 to 6 for mono, 12, 34 or 56 for
stereo)
NOTE
•
Files with formats that are not supported by this
unit will not be recognized even after rebuilding and
cannot be played back.
•
Files with names using characters other than
half-width alphanumeric characters cannot be rebuilt.
NOTE
CANCEL
This unit cannot delete write-protected files and files
that the unit does not recognize.
Press this to not conduct any operation on the selected
folder.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
39
6 – Playback
When the Home Screen is open, use the m [.] and
, [/] buttons to select the take that you want to
play. You can only select takes within the playback area
that is currently set. When there are lots of takes on a card,
for example, setting the play area to a limited number of
takes can make selection easier.
Searching forward and backward
On the Home Screen, when stopped or during playback,
press and hold the m [.] button or , [/]
button to search backward or forward.
On the PLAYpage, you can set the playback area to all
takes, the current folder or the currently loaded take.
Selecting a take for playback
You can also set a folder for playback on the BROWSE
screen.
On the Home Screen, use the m [.] button or ,
[/] button to select a take for playback.
NOTE
On the BROWSE screen, regardless of the current
playback area setting, you can select and play any
take on the card.
Playback
Starting playback
On the Home Screen, when the unit is stopped, press the
PLAY/PAUSE button to start playback.
When in the middle of a take, press the m [.] button
to return to the beginning of that take.
When stopped at the beginning of a take, press the m
[.] button to skip to the beginning of the previous take.
When at the beginning of or in the middle of a take, press
the , [/] button to skip to the beginning of the next
take.
NOTE
•
•
Only takes in the playback area can be played.
Information about the take being played, including
the name, is shown.
Changing the playback position
(scrubbing)
On the Home Screen, when stopped or during playback,
use the DATA wheel to change the playback position.
NOTE
•
Only takes in the playback area can be played. (See
You can also start playback by selecting a take on the
BROWSE screen.
•
Stopping playback
On the Home Screen, press the STOP button during
playback to stop playing a take and return to its beginning.
Pausing playback
On the Home Screen, press the PLAY/PAUSE button
during playback to pause playback at the current position
in the take.
Press the PLAY/PAUSE button again to restart playback
from that position.
NOTE
•
No sound is output while you are turning the DATA
wheel.
•
If you turn the DATA wheel during playback, playback
restarts at the position located when you stop turning
the DATA wheel.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
40
6 – Playback
7. When you have finished making the settings, press the
Mixing and outputting a multitrack
recording
HOME/DISP button to return to the Home Screen.
NOTE
This function cannot be used when playing a stereo
track.
When playing back the sound of a multitrack recording,
you can use the unit’s internal mixer to make a stereo mix
and then output that.
Adjust the playback sound of tracks 1–6 using mixer
channels 1–6. You can also adjust the overall level of the
mix.
You can output the stereo mix that you have mixed using
the internal mixer to the PHONE and DIGITAL/SYNC OUT
jacks.
Using the solo function
Press and hold one of the channel number (1–6) buttons
on the front panel to enable solo monitoring for that
channel.
In addition, if the I/Opage LINE OUTitem is set to MIX
,
a stereo mix can be output from the LINE OUTPUTS jacks.
When set this way, the sound of the left (L) channel is
output through LINE OUTPUTS 1, 3 and 5 and the sound
of the right (R) channel is output through LINE OUTPUTS
2, 4 and 6.
When solo monitoring, the
on the Home Screen, and the indicator appears for
the soloed channel.
indicator appears
Using the internal mixer
1. Press the MIX LEVEL button to open the LEVEL
screen.
To turn solo monitoring off, press and hold the corre-
2. Adjust the levels of channels 1–6 and the overall mix
on this screen. Use the channel number (1–6) and MIX
[LOCK] buttons to select the channels that you want
to adjust.
sponding channel number (1–6) button again.
NOTE
Solo monitoring can only be used with headphones
and the built-in speaker.
3. Use the VALUE/MARK knob to adjust the optimal level
in a range between 0 and 100 (default value is 100).
4. Press the MIX PAN button to open the PANscreen.
Playing a stereo track
In addition to multitrack recording, this unit can also
record a stereo track simultaneously. For example, a 6-track
multitrack and a stereo track can be recorded at the same
time.
During playback, press the MULTI/STEREO button to
switch between the multitrack and the stereo track
5. Use the pan controls on this screen to adjust the stereo
position of each channel. Use the channel number
(1–6) buttons to select the channels that you want to
adjust.
NOTE
Multiple channels can be linked and controlled at the
6. Use the VALUE/MARK knob to adjust each to a
suitable stereo position using values ranging from L10–
L1 (left) to C (center) and R1–R10 (right). (Odd number
channels are set to L10 and even number channels are
set to R10 by default.)
During playback of the stereo track, the
appears on the Home Screen.
icon
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
41
6 – Playback
Setting the playback area
Setting the search speed
1. Press the MENU button to open the PLAYpage of the
1. Press the MENU button to open the PLAYpage of the
MENUscreen.
MENUscreen.
2. Use the DATA wheel to select the AREAitem, and press
2. Use the DATA wheel to select the SEARCHSPEEDitem,
the MARK (¯) button or ENTER/MARK button.
and press the ENTER/MARK button.
3. Use the DATA wheel to set the playback area.
3. Use the DATA wheel to set the search speed to x2, x4
,
x8(default value) or x10
.
SINGLE: Play only the selected take.
FOLDER (default value): Play all the takes in the
currently selected folder on the BROWSEscreen.
4. When you have finished making the settings, press the
HOME/DISP button to return to the Home Screen.
ALL: Play all takes in the MUSIC Folder on the SD card.
4. When you have finished making the settings, press the
Repeat playback
HOME/DISP button to return to the Home Screen.
You can set the unit to repeatedly play a single take or all
takes in a folder.
Selecting a folder for the playback
area on the BROWSE screen
1. When the Home Screen is open, press the FUNCTION
button to open the Functions Screen.
2. Use the VALUE/MARK knob to move the cursor and
Regardless of the current playback area, if you play a take
on the BROWSEscreen, the playback area changes to the
folder that contains that take.
select the REPEATmenu item.
3. Press the VALUE/MARK knob to turn the repeat
playback ON or OFF.
1. Press the MENU button to open the GENERALpage of
If the repeat has been turned ON, the REPEAT
indicator appears with a dark background.
the MENUscreen.
2. Use the DATA wheel to select the BROWSEmenu
item, and press the ENTER/MARK button to open the
BROWSEscreen.
3. Use the DATA wheel to select the folder that contains
the take that you want to play.
NOTE
4. When you have finished making the settings, press the
For additional information about how to navigate the
BROWSE screen, see “Navigating the BROWSE screen”
HOME/DISP button to return to the Home Screen.
NOTE
4. Press the MARK (¯) button.
5. Select the take that you want to play.
•
The
icon appears on the Home Screen when the
repeat function is ON.
•
6. Press the ENTER/MARK button to open the following
The takes in the currently set playback area are
repeated. (See “Setting the playback area” on page
42.)
pop-up menu.
Use the DATA wheel to choose PLAY, and press the
ENTER/MARK button to return to the Home Screen.
The selected take begins to play. If the playback area
is set to FOLDER, the folder that contains that take
becomes the playback area.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
42
7 – Connection with a computer
By connecting this unit with a computer using the
included USB cable, you can copy audio files between the
SD card in the unit and the computer.
This unit can handle MP3 (96, 128, 192, 320 kbps, 44.1 k/48
kHz) and WAV/BWF (44.1 k/48 k/96 k/192 kHz, 16/24-bit)
audio files.
This unit appears on the computer as an external drive
named “DR-680MK2”.
On Windows, open “My computer”to show the
“DR-680MK2”drive.
On Mac OS X, the “DR-680MK2”drive should appear on the
desktop or in the Finder sidebar, depending on the system
settings.
Click on the “DR-680MK2”drive to show the “MUSIC”and
“UTILITY”folders.
Computer
USB
NOTE
Instead of connecting this unit to a computer by
USB, you can also perform the same operations by
removing the SD card and connecting it directly to a
computer using a card reader, for example.
Confirm that an SD card is inserted correctly into the unit.
If an SD card is not inserted correctly when the unit is
connected to a computer by USB, a Can'tSaveData
pop-up message appears.
Copying files to a computer
When connected, USBconnectedappears on the display
of this unit.
Open the “MUSIC”folder, and drag-and-drop the files that
you want to copy to any location on the computer.
NOTE
Other unit functions cannot be used when it is
connected to a computer by USB.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
43
7 – Connection with a computer
Copying files from a computer
Ending the connection with a
computer
Drag and drop files from anywhere on the computer to
folders that you create as desired in the “MUSIC”folder.
After you have copied files to an SD card and discon-
nected from the computer, on the BROWSEscreen, select
the folder that you copied the files into and execute the
Follow the correct computer procedures to disconnect
the unit from the computer before disconnecting the USB
cable. Please refer to your computer manual for infor-
mation about the correct procedures for disconnecting an
external drive.
Rebuilding the folder makes it possible for this unit to play
the copied files.
After being disconnected, the power is set to standby.
Before rebuilding, make sure the file and folder names
contain only single-byte alphanumeric characters.
NOTE
•
If you use a computer to change the name of a file or
folder created by this unit, the unit will not recognize
the affected files as takes. Avoid changing names on a
computer if you want to use them again on this unit.
•
Files with formats that are not supported by this
unit will not be recognized even after rebuilding and
cannot be played back.
TIP
•
You can also use the computer to manage the contents
of the “MUSIC” folder.
•
You can create subfolders inside the “MUSIC” folder,
but this unit can only recognize one level of subfolders.
The unit ignores deeper folder levels and the files in
them.
•
•
Since this unit can be set to play the contents of a
single folder, organizing folders by musical category or
artist could be convenient.
This unit can only read files and folders with
names that contain only single-byte alphanumeric
characters.
•
•
Names given to subfolders and files are shown on the
unit’s Home Screen and the BROWSEscreen.
Folders created directly inside the “MUSIC” folder
using a computer can be given names with 16 or more
characters without interfering with the operation of
the unit, but only the first 15 characters will be shown
on its display.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
44
8 – Cascade function
Preparing to use the cascade
function
Cascade recording
When the units are stopped, press the REC button to start
recording with both the master and slave units.
During recording, press the STOP button to stop recording
with both the master and slave units.
1. Connect the DIGITAL/SYNC OUT jack of the master
unit to the DIGITAL SYNC IN jack of the slave unit
using a commercially-available coaxial digital cable.
Press the PAUSE button to pause recording with both the
master and slave units.
Master unit
When paused, press the REC button to resume recording.
When paused, press the PAUSE button or the STOP button
to stop recording.
Cascade playback
When stopped, press the PLAY/PAUSE button to start
playback of both the master and slave units from the
current position.
Slave unit
During playback, press the PLAY/PAUSE button to pause
playback of both the master and slave units at the current
position.
2. Make the following settings using the menus of both
master and slave units.
Disabling cascade operation
8
REC page
Set the CASCADEitem on the SYSTEMpage to OFF
.
o
o
o
FORMAT:
We recommend that you use the same setting for
both the master and slave units.
SAMPLE:
We recommend that you use the same setting for
both the master and slave units.
PAUSE:
This must be set to the same value on both the
master and slave units.
8
8
8
PLAY page
AREA:
For cascade playback, both the master and slave
units must be set the same.
SYSTEM page
o
o
CASCADE:
Set the master unit to MASTERand the slave unit
to SLAVE
.
Function screen
o
REPEAT:
For cascade playback, both the master and slave
units must be set the same.
o
PRE.REC:
Set both the master and slave units to the same
value.
3. Press the HOME buttons on both the master and slave
units to open their Home Screens.
4. Press the STOP button on both the master and slave
units to stop them.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
45
8 – Cascade function
Precautions for use of the cascade
function
•
When the cascade function is ON, the auto record
function is disabled. If you turn the cascade function ON
when the auto record function is ON, the auto record
function turns OFF automatically. When the cascade
function is turned OFF again, the auto record function
remains OFF. To use the auto record function, turn it ON
again after turning the cascade function OFF.
•
•
When using the cascade function, set the PAUSEitem of
the RECmenu to the same value for both the master and
slave units. If the settings of the master and slave units
are different, their operation after pausing recording will
not be the same, and control of their transports will not
occur correctly.
If the types of cards used for recording in the master
and slave units are different and the PAUSEitem of the
RECmenu is set to NEW TAKE, recording might not start
simultaneously when the REC button is operated. The
reason for this is that the processing time for the units
differs when the slave and master units use different
types of cards. Moreover, this lag between units can also
occur if the recording file format or sampling frequency
settings of the master and slave units are not the same.
To conduct cascade recording without lag, use the same
type of card in both the master and slave units and set
their recording file formats and sampling frequencies to
the same values. Alternately, the lag between units can
also be avoided by waiting several seconds after putting
the unit in recording standby before pressing the REC
button.
•
•
The Home Screen must be open on both the master and
slave units to use the cascade function. If a menu screen
is open on either or both units, the cascade function will
not work properly.
Use of the cascade function for playback is intended
for checking recorded takes. We cannot guarantee
synchronized playback.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
46
9 – Other Settings and Information Display
Using mid-side mic decoding
Recording with mid-side decoding
With this unit, you can connect a mid-side mic and
decode the signal while recording. You can also record
without decoding, but check the decoded result with the
monitoring output.
1. On the MS MODEscreen, set the decoding mode to
INPUT
.
2. Press the MIX PAN button on the front panel to open
the PANscreen (pan pot adjustment screen). Use the
MS width control to adjust the width of the mid-side
signal pair.
NOTE
When dual recording is enabled, the mid-side mic
decoding function cannot be used. (See “Enabling dual
Connecting a mid-side microphone
When using this unit’s mid-side decoding function,
connect the mid signal to the odd channel and the side
signal to the even channel in the pair. If you connect them
in reverse, correct decoding is not possible.
For example, connect the mid signal to channel 3 and the
side signal to channel 4.
Press one of the channel number (1–6) buttons on the
front panel that corresponds to one of the mid-side
channels that was set to INPUTon the MS MODE
screen. (For example, press 3 or 4 to adjust paired
channels 3 and 4.)
Use the VALUE/MARK knob to adjust the width of
the signal suitably in a 0–100 range. At 0, only the mid
channel is included in the stereo decoding. As the
value is increased, more of the side channel is included
in the stereo decoding. At 100, only the side channel is
included. (The default value is 0.)
Setting the MS decoding mode
Select the MS MODEitem on the SYSTEMpage to open the
MS MODEscreen.
3. Press the MIX LEVEL button on the front panel to open
the LEVELscreen, and adjust the decoder output.
Set the decoding mode to use when connecting mid-side
microphones. Channel pairs 1-2, 3-4 and 5-6 can each be
set separately.
Press one of the channel number (1–6) buttons on the
front panel that corresponds to one of the mid-side
channels that was set to INPUTon the MS MODE
screen. (For example, press 3 or 4 to adjust paired
channels 3 and 4.)
Use the VALUE/MARK knob to adjust the signal level
suitably in a 0–100 range. The lower the number is, the
lower the output level becomes (default value: 100).
OFF (default value)
Recording and playback use the ordinary mode (no
mid-side decoding).
INPUT
Use this mode to decode while recording.
Playback uses the ordinary mode.
NOTE
•
A take that was recorded without decoding (mid and
MONITOR
side channels recorded as is) can also be decoded
Use to monitor the output of mid-side microphones
with decoding while recording without decoding.
Also use this with a take that was recorded without
decoding to decode it during playback. In that case,
LINE OUTshould be set to MIXon the I/Opage.
during playback by setting MS MODEto MONITOR
.
When decoding during playback, output will be of the
stereo mix.
•
•
To record without decoding, set the MS MODEto OFF
or MONITOR
.
If set to MONITOR, you can monitor the decoded signal
during recording.
NOTE
The MS MODEscreen settings cannot be changed
during recording or playback. Always stop the unit
(the transport icon should be ) before changing the
settings.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
47
9 – Other Settings and Information Display
•
If only one of the channels in a pair set to use MS
decoding is included in the range, none of the channels
will be ganged together.
When dual recording is enabled, the GANG function
cannot be used. (See “Enabling dual recording” on
page 31.)
GANG function
The GANG function allows you to adjust multiple channels
at the same time on the TRIM, PANand LEVELscreens.
Set the range of channels to be ganged by pressing the
channel number (1–6) buttons for the channels at both
ends of the range at the same time.
•
Output settings
For example, to gang channels 3–5, press the 3 and 5
buttons at the same time. When you do so, channels
3-5will appear selected on the screen as shown in the
You can make settings related to analog and digital output.
illustration below.
Analog output settings
You can set the LINE OUTPUT jacks to directly output the
sound of each track or to output the stereo mix sound.
When set to output the MIX, the left and right channels of
the stereo track are output through the analog output jack
1/2, 3/4 and 5/6 pairs.
You can create multiple gangs of channels by setting each
gang separately. However, no channel can be part of more
than one gang.
When ganged, you can adjust parameters for the ganged
channels at the same time.
If the parameter setting for any of the ganged channels
reaches its maximum or minimum value, turning the
VALUE/MARK knob in the same direction will not further
increase or decrease the other channel parameters.
1. Press the MENU button to open the I/Opage of the
MENUscreen.
2. Use the DATA wheel to select the LINE OUTmenu
item, and press the ENTER/MARK button.
If you press and hold the VALUE/MARK knob while
multiple channels are selected, the parameter values for all
of the ganged channels will be set to the lowest value of
the channels.
3. Use the DATA wheel to set it to 1-6(default value) or
MIX x3
.
1-6: The sound of each channel is output directly.
MIX x3: The stereo signal mixed by the internal mixer
is output.
4. When you have finished making the setting, press the
HOME/DISP button to return to the Home Screen.
Any of the following actions will deactivate the GANG
function.
•
Press any button that corresponds to a channel that is
currently ganged.
•
•
•
Put the unit power in standby.
Activate or Deactivate MS decoding.
Use the INITIALIZE function.
When using the GANG function, the ganged channels are
the same on the TRIM, PANand LEVELscreens. However,
channels that have been set to use mid-side decoding
cannot be ganged or unganged on the PANand LEVEL
screens.
NOTE
•
You cannot gang channels that are set to use MS
decoding with channels that are not. However, you can
gang such channels separately.
•
•
You cannot gang channels that are set to use different
types of MS decoding.
When designating a range that includes multiple
channel pairs set to use MS decoding, only the
channels in the pair with the lowest number is ganged.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
48
9 – Other Settings and Information Display
Digital output settings
You can set the digital output format to SPDIF or AES/EBU.
System settings
Use the SYSTEMpage to make various settings to suit
the environment and conditions in which the unit is to be
used, as well as to view system information.
1. Press the MENU button to open the I/Opage of the
MENUscreen.
2. Use the DATA wheel to select the DIGITAL OUTmenu
1. Press the MENU button to open the SYSTEMpage of
item, and press the ENTER/MARK button.
the MENUscreen.
3. Use the DATA wheel to select SPDIF(default value) or
On the SYSTEMmenu screen, you can make various
AES/EBU
.
settings described below.
SPDIF: Output in SPDIF format.
AES/EBU: Output in AES/EBU format.
Use the MARK (Â) and (¯) buttons, ENTER/
MARK button and the DATA wheel to select each item.
4. When you have finished making the setting, press the
2. When you have finished making the settings, press the
HOME/DISP button to return to the Home Screen.
HOME/DISP button to return to the Home Screen.
Power AUTO OFF settings
Use the AUTOOFFitem to set the amount of time since
being last used until the unit’s power automatically turns
OFF when operating on batteries.
Options: OFF(default value—AUTO OFF disabled), 3min
,
5min, 10min, 30min
Turning the backlight off automatically
Use the BACKLIGHTitem to set the amount of time since
being last used until the backlight automatically turns OFF
when operating on batteries.
Options: OFF, 5sec(default value), 10sec, 15sec, 30sec
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
49
9 – Other Settings and Information Display
Cascade settings
Initializing the unit
Use the CASCADEitem to set the cascade function.
Options: OFF(default value—cascade disabled), MASTER
SLAVE
Use the INITIALIZEitem to restore the various settings of
this unit to their initial settings.
,
When selecting Execitem, press the ENTER/MARK button
to open a confirmation screen.
Setting the extent of the panel operation
lock function
Use the LOCK MODEitem to set the lock function.
You can set which controls are disabled when you engage
the panel operation lock function, which is activated by
pressing and holding the MIX [LOCK] button.
TOP: Button operation of the top panel is disabled.
FRONT: Button operation of the front panel is disabled.
Press the ENTER/MARK button to initialize the unit. Press
the STOP button to cancel initialization.
After completing or canceling initialization, the SYSTEM
page reopens.
T+F: Button operation of both the front and top panels is
disabled.
Viewing system information
Use the INFORMATIONitem to view information about the
unit’s system settings and the firmware version.
Setting the battery type
Use the BATTERYitem to set the type of battery used.
The unit uses this setting to display the remaining battery
charge and determine the minimum necessary remaining
charge for correct operation.
Press the ENTER/MARK button to open the system infor-
mation screen.
Options: ALKALI(alkaline batteries (default value)), NiMH
(nickel metal hydride batteries), LiFeS2(lithium battery)
This page shows information about the system firmware
version.
When the INFORMATIONscreen is open, press the ENTER/
MARK button to return to the SYSTEMscreen.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
50
9 – Other Settings and Information Display
Reformatting SD cards
Viewing SD card information
You can reformat an SD card that is in the unit.
On the CARDpage, information about the status of the
currently inserted SD card is shown.
CAUTION
1. Press the MENU button to open the CARDpage of the
•
If you format a card, all information, including takes
and folders, on it is erased.
MENUscreen.
2. Use the DATA wheel to select the INFORMATIONitem,
•
When formatting, use the AC adaptor or confirm
that the remaining battery charge is sufficient. If the
batteries run out of power during this operation, the
formatting might not be completed correctly.
and press the ENTER/MARK button.
1. Press the MENU button to open the CARDpage of the
MENUscreen.
2. Use the DATA wheel to select the FORMATitem, and
press the ENTER/MARK button to open the following
screen.
A pop-up showing the use status of the SD card will
appear.
3. Press the ENTER/MARK button again to open the
TOTAL
following screen.
Shows the total memory capacity of the SD card.
REMAIN
Shows the remaining capacity of the SD card.
FILE/FLDR
Shows the total number of files and folders inside
the MUSIC folder.
4. Use the DATA wheel to select one of the following
settings.
Options: QUICK FORMAT(default), ERASE FORMAT
NOTE
Using the ERASE FORMAToption might restore an SD
card that has decreased writing performance due to
repetitive use.
5. Press the ENTER/MARK button to open a confirmation
screen.
6. Press the ENTER/MARK button again to start
formatting.
NOTE
When ERASE FORMATis being executed, you can
press the MARK (.) button on the top of the unit
to cancel. Doing this will have the same result as using
QUICK FORMAT
.
7. When formatting completes, the CARDscreen reopens.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
51
10 – Messages
The following is a list of the pop-up messages that might appear on the DR-680MKII under certain conditions.
Refer to this list if one of these pop-up messages appears and you want to check the meaning or determine a suitable
response.
Message
Meaning and response
The battery is almost out of power. Replace the AA batteries.
The card is not formatted properly or the formatting is broken. Change the card
or press the ENTER/MARK button when this message appears to format the card
in FAT format.
Battery Empty
MBR Error Init CARD
CAUTION: Execution of FAT formatting erases all data currently on the card.
The FAT formatting of the card is abnormal or broken. This message also appears
if you FAT formatted the card using a computer connected by USB and if a new
card is inserted in the unit. Always use the DR-680MKII to conduct FAT formatting
of cards to be used with it. Change the card or press the ENTER/MARK button
when this message appears to format the card in FAT format.
Format Error Format CARD
CAUTION: Execution of FAT formatting erases all data currently on the card.
The system file is missing. This unit requires a system file for operation. When this
message appears, press ENTER/MARK to automatically create a system file.
The system file required to operate this unit is invalid. When this message
appears, press ENTER/MARK to automatically create a system file.
Something might be wrong with the card. Change the card. This message will
appear with SDXC cards of 256 GB or lager.
File Not Found Make Sys File
Invalid SysFile Make Sys File
Invalid Card Change Card
This appears when the card is protected and lacks the necessary MUSIC Folder
and other folders and files. Unlock the write protect switch, restart the power and
format the card.
Writing to the SD card was not fast enough. Back up files to a computer and then
use the ERASE FORMAT function on the unit.
Protected Card Change Card
Write Timeout
If this occurs even after formatting the SD card, the card transmission rate is too
slow. Change the SD card.
The SD card has no remaining capacity. Erase unnecessary takes or move them to
your computer to make open space.
The file is larger than the designated size or the recording time exceeded 24
hours.
The total number of folders and files exceeds 5000. Erase unnecessary files or
move them to your computer.
Card Full
Max File Size
File Full
The total number of takes exceeds 1000. Erase unnecessary takes or move them
to your computer.
The SD card could not be handled properly. Replace the card.
The take includes the read only file and cannot be erased.
No SD card is loaded. Insert a recordable SD card.
Take Full
Card Error
File Protected
No Card
An audio file could not be found inside the take. The audio files in the take might
have been erased or renamed using a PC. Restore the files or erase the take using
the BROWSE screen.
File Not Found in TAKE
When the DIGITAL/SYNC IN input is selected, the DIGITAL IN connection has
been lost or the sampling frequency is incorrect.
Confirm that the external digital device is connected to the DIGITAL/SYNC IN
jack correctly. Confirm that the sampling frequency used by the external digital
device and this unit are compatible.
DIN unlock
Press the STOP button to close this message.
If you do this, you will not be able to use the DIGITAL/SYNC IN, but otherwise
recording will be possible.
If this message appears during recording, noise might be recorded."
DIN unlock status has ended. DIGITAL IN has become possible.
DIN lock
Press the STOP button to close this message.
If this message appears during recording, noise might be recorded."
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
52
10 – Messages
Message
Meaning and response
Not Continued
File Error
Can't Save Data
Player Error
Device Error
Writing Failed
Sys Rom Err
If any of these errors occur, turn the unit power OFF and restart it. If the power
cannot be turned OFF, remove the batteries and disconnect the AC adaptor (if
connected). If the error message continues to appear, please contact a TASCAM
Service Center.
System Err 50
System Error 1
System Error 2
System Error 3
System Error 4
System Error 5
System Error 6
System Error 7
System Error 8
System Error 9
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
53
11 – Troubleshooting
8
If you are having trouble with the operation of this unit,
please try the following before seeking repair. If these
measures do not solve the problem, please contact the
store where you bought the unit or a TASCAM Service
Center.
The recording level is low.
•
•
•
Is the trim setting too low?
Is the MIC GAIN set to LOW?
Is the output level of a connected external device too
low?
8
Power will not turn ON.
8
The sound I am trying to record is distorted.
•
•
Confirm that the batteries are not dead.
Confirm that the batteries are installed with the correct
¥/^ orientations.
•
•
Is the trim setting too high?
Is the MIC GAIN set to HIGH?
•
Confirm that the power plug of the AC adaptor
(GPE248-120200-Z) is connected securely.
8
I cannot erase a file.
•
•
Confirm that the SD card is not write-protected.
Are you trying to delete a file that has been set to
read-only on a computer?
8
The unit is not responding to operations.
•
Is the button lock function ON?
8
SD card is not recognized.
8
Files on this device do not appear on a computer.
•
•
Confirm that the SD card is inserted securely.
Confirm that the USB port of the unit is connected with
the computer.
Are you using a USB hub?
8
Playback is not possible.
•
•
•
If it is a WAV/BWF file, confirm that it is of a compatible
sampling frequency.
Is the unit recording or in recording standby?
•
If it is an MP3 file, confirm that it is of a compatible
bit-rate.
8
No sound is output from the built-in speaker
•
•
•
Are headphones connected?
Is the SPEAKER item set to OFF?
Is the volume level of the headphones minimized?
8
No sound is output from the headphones
•
Is the volume level of the headphones minimized?
8
No sound is output from the monitoring system
•
•
•
Confirm that the monitoring system is connected
correctly.
Is the volume level of the connected monitoring system
minimized?
Is the output level of this unit minimized?
8
Recording is not possible.
•
•
•
•
•
Reconfirm connections.
Reconfirm the input settings.
Check whether the recording level is too low.
Confirm that the SD card is not full.
Confirm that the maximum number of files or takes has
not been reached.
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
54
12 – Specifications
Recording media and formats
Input and output
Recording media
SD card (64MB – 2 GB)
SDHC card (4 GB – 32 GB)
SDXC card (48 GB – 128 GB)
Analog audio input and output
MIC/LINE INPUTS
Connectors:
Supported recording and playback formats
BWF: 16/24-bit, 44.1/48/96/192 kHz
WAV: 16/24-bit, 44.1/48/96/192 kHz
MP3: 96/128/192/320 kbps, 44.1/48 kHz
XLR-3-31
(1: GND, 2: HOT, 3: COLD)
6.3mm (1/4”) standard TRS jacks
(Tip: HOT, Ring: COLD, Sleeve: GND)
INPUT switch set to MIC (phantom power supported)
Input impedance: 2.4 kΩ
Number of tracks
6 tracks and a stereo mix track
BWF: 44.1/48/96 kHz
WAV: 44.1/48/96 kHz
MP3: 44.1/48 kHz
2 tracks
Nominal input level:
GAIN LOW: –20 dBu (0.11 V)
GAIN HIGH: –44 dBu (6.91 mV)
Maximum input level:
GAIN LOW: +3 dBu (1.55 V)
GAIN HIGH: –21 dBu (0.098 V)
Minimum input level:
BWF: 192 kHz
WAV: 192 kHz
File recording modes
GAIN LOW: –51.5 dBu (2.0 mV)
GAIN HIGH: –75.5 dBu (0.1 mV)
INPUT switch set to LINE
BWF: monaural, stereo, 6-channel
WAV: monaural, stereo, 6-channel
MP3: monaural, stereo
Input impedance: 10 kΩ
Nominal input level: +4 dBu (1.23 V)
Maximum input level: +24 dBu (12.3 V)
Minimum input level: –27.5 dBu (0.05 V)
LINE OUTPUTS jacks
Connectors: standard RCA pin jacks
Output impedance: 200Ω
Nominal output level: –10 dBV (0.3 V)
Maximum output level: +6 dBV (2.0 V)
PHONES jack
Connector: standard 6.3 mm (1/4”) stereo jack
Maximum output: 50 mW + 50 mW (into 32Ω load)
Built-in speaker
500 mW (monaural)
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
55
12 – Specifications
Digital audio input and output
Other specifications
DIGITAL/SYNC IN jack
Power supply
Connector: RCA pin jack
Format: IEC60958-3 (S/PDIF) or AES3-2003/IEC60958-4
(AES/EBU) automatically determined
8 AA batteries (alkaline, NiMH or lithium)
AC adaptor (GPE248-120200-Z, 100-240V, 50-60 Hz,
included)
DIGITAL/SYNC OUT jack
Power consumption
Connector: RCA pin jack
Format: IEC60958-3 (S/PDIF) or AES3-2003/IEC60958-4
(AES/EBU) set by user
100-120V: 9W (When phantom power ON and GPE248-
120200-Z AC adaptor used)
220-240V: 9.5W (When phantom power ON and
GPE248-120200-Z AC adaptor used)
Control input and output
Battery operation time (when used continuously)
Alkaline batteries (EVOLTA)
USB connection
About 3.5 hours (6 channels of phantom power
used, 3 mA per channel)
About 4.5 hours (2 channels of phantom power
used, 3 mA per channel)
USB port connector: Mini-B type
Format: USB2.0 HIGH SPEED (480 Mbps)
Audio performance
About 6 hours (phantom power not used)
NiMH batteries (eneloop)
(From LINE IN to LINE OUT, Input level = FS –1 dB)
About 4 hours (6 channels of phantom power used,
3 mA per channel)
About 4.5 hours (2 channels of phantom power
used, 3 mA per channel)
Frequency response
20 Hz-20 kHz +0.5/–1.5 dB (44.1 kHz)
20 Hz-20 kHz +0.5/–0.5 dB (48 kHz)
20 Hz-40 kHz +0.5/–1.0 dB (96 kHz)
20 Hz-80 kHz +0.5/–5.0 dB (192 kHz)
About 5.5 hours (phantom power not used)
Lithium batteries (Energizer Ultimate Lithium)
About 7.5 hours (6 channels of phantom power
used, 3 mA per channel)
Distortion
About 9.5 hours (2 channels of phantom power
used, 3 mA per channel)
About 11 hours (phantom power not used)
0.007% (1 kHz)
S/N ratio
100 dB (A-weighted)
Dimensions (width x height x depth)
216.4 x 56 x 188.4 mm
8.52 x 2.21 x 7.41 in
Weight
1.2 kg/2.646 lb (without batteries)
Operating temperature range
0–40º C/32–104º F
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
56
12 – Specifications
Dimensions
202mm
54mm
56mm
216.4mm
•
•
Illustrations in this manual might differ from the actual product.
In order to improve the product, specifications and appearance could be changed without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download. TASCAM DR-680
57
12 – Specifications
Block diagrams
8
Recording
8
Play
TASCAM DR-680MKDIoI wnload from Www.Somanuals.com. All Manuals Search And Download.
58
12 – Specifications
8
I/O
✂
WARRANTY
< In the United States >
WHAT WE WILL PAY FOR
< Europe >
We will pay all labor and material expenses for items covered by
the warranty. Payment of shipping charges is discussed in the
next section of this warranty.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state. This warranty is
only valid within the country the unit was originally purchased.
This product is subject to the legal warranty regulations of the
country of purchase. In case of a defect or a problem, please
contact the dealer where you bought the product.
HOW YOU CAN GET WARRANTY SERVICE
Ce produit est sujet aux réglementations concernant la garantie
légale dans le pays d’achat. En cas de défaut ou de problème,
veuillez contacter le revendeur chez qui vous avez acheté le
produit.
WHAT IS AND IS NOT COVERED
Your unit must be serviced by an authorized TASCAM service
station in the United States. (This warranty is not enforceable
outside the U.S.) If you are unable to locate an authorized
TASCAM service station in your area, please contact us. We either
will refer you to an authorized service station or instruct you
to return the unit to the factory. Whenever warranty service is
required, you must present a copy of the original dated sales
receipt from an Authorized TASCAM Dealer.
Except as specified below, this warranty covers all defects in
materials and workmanship in this product. The following are
not covered by the warranty:
D i e s e s G e r ä t u n t e r l i e g t d e n g e s e t z l i c h e n
Gewährleistungsbestimmungen des Landes, in dem es erworben
wurde. Bitte wenden Sie sich im Gewährleistungsfall an den
Händler, bei dem sie das Gerät erworben haben.
1. Damage to or deterioration of the external cabinet.
2. Damages resulting from accident, misuse, abuse or
neglect.
3. Damage resulting from failure to perform basic
daily maintenance and/or calibration or otherwise
resulting from failure to follow instructions contained
in your owner’s manual.
4. Damage occurring during shipment of the product.
(Claims must be presented to the carrier)
5. Damage resulting from repair or attempted repair
by anyone other than TEAC or an authorized TASCAM
service station.
6. Damage resulting from causes other than product
defects, including lack of technical skill, competence,
or experience of the user.
Questo apparecchio è conforme alle norme sulla garanzia vigenti
nel rispettivo Paese in cui esso è stato acquistato. Si prega
di rivolgersi al proprio commerciante, presso il quale è stato
acquistato l’apparecchio, nel caso in cui si voglia richiedere una
prestazione in garanzia.
You must pay any shipping charges if it is necessary to ship the product
to service. However, if the necessary repairs are covered by the warranty,
we will pay return surface shipping charges to any destination within
the United States.
LIMITATION OF IMPLIED WARRANTIES
Las condiciones de garantía de este aparato están sujetas a las
disposiciones legales sobre garantía del país en el que ha sido
adquirido. En caso de garantía, debe dirigirse al establecimiento
donde adquirió el aparato.
Any implied warranties, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
are limited in duration to the length of this warranty.
EXCLUSION OF DAMAGES
< In other countries/areas >
TEAC’s liability for any defective product is limited to repair or
replacement of the product, at TEAC’s option. TEAC shall not be
liable for:
7. Damage to any unit which has been altered or on
which the serial number has been defaced, modified
or is missing.
This warranty gives you specific legal rights, and you may also
have other rights that vary by country, state or province.
If you have a warranty claim or request, please contact the dealer
where you bought the product.
1. Damages based upon inconvenience, loss of use of
the product, loss of time interrupted operation or
commercial loss; or
2. A n y o t h e r d a m a g e s , w h e t h e r i n c i d e n t a l ,
consequential or otherwise.
Some states do not allow limitations on how long an implied
warranty lasts and/or do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations and
exclusions may not apply to you.
WHO MAY ENFORCE THE WARRANTY
This warranty may be enforced only by the original purchaser.
该保证书赋予了顾客
家，州或省等地域的不同，顾客可能拥有其他权
求保修，请与购买本产品的销
特定的合法权利，并且因国
LENGTH OF WARRANTY
利。如需申请或要
All parts except heads and disk drives are warranted for one (1)
year from the date of original purchase. Heads and disk drives
are warranted to ninety (90) days from date of original purchase.
Labor is warranted for ninety (90) days from date of original
purchase.
售店进行联系。
If you require repair services for your TASCAM equipment,
please contact the dealer where the product was purchased from
or the TASCAM Distributor in your country. A list of TASCAM
To locate an Authorized Service Center in Your Distributors can be found on our website at: http://teac-
Area
CALL 1-800-447-8322
global.com/
Download from Www.Somanuals.com. All Manuals Search And Download.
TEAC CORPORATION
Phone: +81-42-356-9143
1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan
TEAC AMERICA, INC.
Phone: +1-323-726-0303
1834 Gage Road, Montebello, California 90640 USA
TEAC MEXICO, S.A. de C.V.
Phone: +52-55-5010-6000
Río Churubusco 364, Colonia Del Carmen, Delegación Coyoacán, CP 04100, México DF, México
TEAC UK LIMITED
Printed in China
Phone: +44-8451-302511
Meridien House, Ground Floor,69 - 71, Clarendon Road, Watford, Hertfordshire, WD17 1DS, UK
TEAC EUROPE GmbH
Phone: +49-611-71580
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
TEAC SALES & TRADING(SHENZHEN) CO., LTD
Phone: +86-755-88311561~2
Room 817, Block A, Hailrun Complex, 6021 Shennan Blvd., Futian District, Shenzhen 518040, China
✂
WARRANTY
Model/Modèle/Modell
Modello/Modelo/型号
Owner’s name/Nom du possesseur/Name des Eigentümers
Nome del proprietario/Nombre del propietario/顾客姓名
DR-680)"
Serial No./No de Série/Seriennummer
Address/Adresse/Adresse
Indirizzo/Dirección/顾客地址
Numero di serie/Número de serie/序列号
Date of purchase/Date de l’achat/Datum des Kaufs
Data dell’acquisto/Fecha de compra/购买日期
Dealer’s name/Nom du détaillant/Name des Händlers
Nome del commerciante/Nombre del establecimiento/销售店名
Dealer’s address/Adresse du détaillant/Adresse des Händlers
Indirizzo del commerciante/Dirección del establecimiento/销售
店地址
Download from Www.Somanuals.com. All Manuals Search And Download.
|