Quick Installation Guide
TPL-310AP
1.01
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Before You Start
Package Contents
ŸTPL-310AP
ŸCD-ROM (Utility and User’s Guide)
ŸMulti-Language Quick Installation Guide
ŸNetwork Cable (1.5m/4.9ft)
System Requirements
ŸCD-ROM Drive
ŸA Desktop or Laptop PC with or wireless Network Adapter Installed
ŸExisting 10/100Mbps wired network when TPL-310AP is used to a powerline network to an
existing wired network
ŸWeb Browser: Internet Explorer (6.0 or higher)
ŸAdditional HomePlug® AV powerline adapter (e.g. TRENDnet TPL-303E, TPL-304E,
TPL-305E, or another TPL-310AP).
Note: You will need at least 2 powerline adapters to establish a powerline network. Please
ensure that you have an additional powerline adapter before following the installation
procedure for this product.
Software Utility Requirements
Supported Operating Systems
Windows 7 (32/64-bit)
CPU
Memory
1GHz or above
1GB RAM or above
512MB RAM or above
256MB RAM or above
Windows Vista (32/64-bit)
Windows XP (32/64-bit)
800MHz or above
300MHz or above
Note:
The configuration utility will allow you to add security to your powerline network by providing
you with the ability to change the default network name and create your own personal
network name for your powerline network. The utility can also help you to troubleshoot
connectivity between powerline adapters by verifying the network name. Please refer to the
User's Guide on the TPL-310AP CD-ROM for instructions on installing and using the utility.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
200Mbps Powerline AV
Wireless N Access Point
(TPL-310AP)
Media Server
Game
Console
Wireless N 4-Port Media Bridge
(TEW-640MB)
Wireless N
USB Adapter
(TEW-624UB)
Powerline AV Adapter
(TPL-303E)
Router
Powerline AV
Adapter
(TPL-303E)
Internet
Wireless 300Mbps
Powerline
10/100Mbps
The installation diagram shows a typical setup of the TPL-310AP extending your wireless network
connectivity to another room when bridged with an additional powerline adapter, in this case, the
TRENDnet TPL-303E. Assuming you have the TPL-310AP and one additional TRENDnet
Powerline AV adapter, this guide will provide the procedure to installing and configuring the
TPL-310AP with one additional TRENDnet Powerline AV adapter to extend your wireless network
to another room (not in the same room as the router and modem). The orange line represents the
powerline connectivity established through your home's electrical system and the blue lines
represent Cat. 5, 5e, 6 Ethernet connectivity to your network enabled appliances such as a
computer, router, or IP set top box connected to your television. The green lines represent the
wireless connectivity from your wireless device (e.g. laptop computer, media bridge, etc.) to the
TPL-310AP.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
2. Configure the TPL-310AP
Note:
When installing for the first time, it is required that you configure the Access Point from a wired
computer. Assign a Static IP address to your computer's network adapter in the subnet of
192.168.10.x. Since the Access Point's default IP address is 192.168.10.100, make sure no other
network devices are assigned an IP address of 192.168.10.100. (Refer to Troubleshooting section
on how to configure TCP/IP settings on your PC.)
1. Plug the TPL-310AP into an available power
outlet. The TPL-310AP should be within reach
of your computer's network cable.
Outlet
2. Connect a network cable from the TPL-310AP's
network port into your computer's network port.
3. Move the Power switch to the “On” position.
4. Assign a Static IP address to your computer's
network adapter in the subnet of 192.168.10.x.
(Refer to Troubleshooting section on how to
configure TCP/IP settings on your PC.)
5. Open your web browser, type
http://192.168.10.100 in the Address bar, and
then press Enter.
6. Enter the User Name and
password and then click OK. Default Settings:
User name: admin
Password: admin
Note: User name and Password are case
sensitive.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
7. The Setup Wizard will automatically appear.
Click Setup Wizard if the Setup Wizard does
not automatically appear.
8. Click Next.
9. For DHCP, click on the drop down arrow and
Select Client for DHCP to have the TPL-310AP
automatically obtain an IP address from your
DHCP server (router). If Disabled is selected
for DHCP, you will need to configure the
following:
IP address: The assigned IP address should
match your network (e.g. 192.168.10.x,
192.168.0.x, 192.168.1.x). This IP address
should not be used by any other network
device on your network.
Subnet Mask: In most cases, the default
Subnet Mask (255.255.255.0) should be fine.
Then click Next.
Note: It is recommended to manually configure
the LAN Interface Settings (IP address and
Subnet Mask) in case you need to access the
TPL-310AP in the future. Please write down
the IP settings assigned for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
10. You will need to configure the following:
Band: In most cases, the default setting
(2.4GHz (B+G+N) should be fine.
Mode: In most cases, the default setting (AP)
should be fine.
Network Type: This setting does not apply to
(AP) mode. Continue to the next setting.
SSID: The SSID is the wireless network name
of your wireless network (e.g. wireless router
or access point). Enter a unique SSID
(Network Name). Do not use anything that
would be identifying like “Smith Family
Network”. Choose something that can be
easily identified when searching for available
wireless networks.
Channel Width: In most cases, the default
Setting (20MHz) should be fine.
Channel Number: This setting only applies if
the Channel Width is set to 40MHz. In most
cases, the default setting should be fine.
Enable Mac Clone (Single Ethernet Client):
In most cases, the default setting should be
fine.
Then click Next.
Note:
1. To protect your network from any unauthorized access it is recommended to enable wireless
encryption.
2. Once encryption is enabled on the Wireless Access Point, each wireless computer or device
must be configured with the same encryption key.
3. The example below is for WPA2 (AES) security. If you select WPA or WPA2, make sure your
wireless adapters support WPA or WPA2. If your wireless adapters do not support WPA or
WPA2, then select WEP.
4. For Wi-Fi Protected Setup (WPS) instructions please refer to the User's Guide on the CD-ROM.
WPS instructions will vary depending on your wireless adapter. Please contact the manufacturer
of your wireless
Download from Www.Somanuals.com. All Manuals Search And Download.
5
11. Select WPA2(AES).
12. Select Passphrase or Hex (64 characters)
for Pre-Shared Key Format.
13. Enter characters for your Pre-Shared key and
then click Next. For WPA-PSK or WPA2-PSK,
the Pre-Shared Key must be between 8 and
63 ASCII (Passphrase) or 64 (HEX 0-9 & A-F)
characters. Make sure to copy down the
Pre-Shared Key. Use the same encryption key
on your wireless computer or other wireless
device to connect to the TPL-310AP wirelessly.
14. Please wait 25 seconds while the TPL-310AP
reboots.
15. After the settings are applied and the device
has rebooted, disconnect the TPL-310AP from
the power outlet.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
3. Create a powerline network
Note:
1. DO NOT install the TPL-310AP until instructed to do so.
2. DO NOT plug the TPL-310AP into a surge protector or power strip.
3. It is NOT recommended to use this product on electrical systems that use AFCI circuit breakers
or plugged into GFI protected outlets as this may cause performance degradation or loss in
connectivity.
4. Assuming that the TPL-310AP and other TRENDnet Powerline AV devices are configured with
the default settings, to create a powerline network, simply connect the TPL-310AP and other
TRENDnet Powerline AV devices to wall outlets that are on the same electrical system. No
additional configuration in the utility is necessary.
5. Avoid connecting the TPL-310AP into an outlet that has appliances (e.g. refrigerators, washer
and dryer) plugged in.
6. This TPL-310AP 200Mbps Powerline AV Wireless N Access Point needs to pair with at least one
other HomePlug® AV compatible powerline device. (e.g. TRENDnet Powerline AV products
TPL-303E, TPL-304E, TPL-305E, or another TPL-310AP.
7. In order for the TPL-310AP to link to your other TRENDnet Powerline AV devices, each unit must
be on the same electrical system.
8. A maximum of 16 TPL-310AP and other TRENDnet Powerline AV devices can be networked.
Below is an example showing how to create a Powerline network using TPL-310AP,
TPL-303E and an existing router to share Internet.
1. Plug a TPL-303E or other TRENDnet Powerline
AV adapter into an available power outlet. This
powerline adapter should be located within the
reach of the router's network cable.
Outlet
2. Connect a network cable from the powerline
adapter to an available LAN network port on
your router (e.g. TEW-691GR).
Download from Www.Somanuals.com. All Manuals Search And Download.
7
3. Plug the TPL-310AP into an available power
outlet in your desired location to extend
wireless connectivity. Please refer to the
Wireless Tips section for optimal placement of
the TPL-310AP.
Outlet
4. (OPTIONAL) Connect a network cable from the
TPL-310AP into the network port on your
remote computer or network appliances (e.g.
Game Console, IP Set box, network enabled
TV, etc.).
Outlet
5. Verify that the WIFI (Wireless) (Blinking/Green),
ETH (Ethernet) (Green), PL (Powerline) and
PWR (Power) (Solid/Green) LEDs are on for
the TPL-310AP.
Your installation is now complete
For detailed information regarding the TPL-310AP configuration and advanced settings,
please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
Thank you for choosing TRENDnet
Download from Www.Somanuals.com. All Manuals Search And Download.
8
4. LEDs and Buttons
WPS (Wi-Fi Protected Setup)
ETH(NetworkPort)
WIFI(Wireless)
PL(Powerline)
PWR(Power)
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Note:
The Network Port, WPS button, Reset button and Sync button are located at the bottom of the
device.
Network Port
WPS
Reset :
1. Hold for 1 second to reset power line setting
only.
2. Hold for 5 seconds to reset AP settings only.
Sync
The Power switch is located at the top of the device.
PowerSwitch
*Note: The following factors may affect the powerline network's connection quality:
· Noise – Generated by appliances that are connected to your electrical system through power
outlets that have high power consumption requirements. (e.g. Microwaves, ovens, blow dryer,
iron, dishwasher, etc.) The quality of your household electrical wiring may also cause
additional noise on your electrical system.
· Distance – Long lengths of electrical wiring through your electrical system between connected
powerline adapters.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Troubleshooting
1. How do I configure TCP/IP settings on my computer's network adapter?
Windows 7
1. Go into the Control Panel, click Network and Internet,
click Network and Sharing Center, click Change
Adapter Settings and then right-click the Local Area
Connection icon and then click Properties.
2. Click Internet Protocol Version 4(TCP/IPv4)
and then click Properties. Then click on Use
the following IP address, and make sure you
assign your network adapter an IP address in
the subnet of 192.168.10.x.
Windows Vista
1. Go into the Control Panel, click Network and Internet,
click Network and Sharing Center, click Manage
Network Connections and then right-click the Local
Area Connection icon and then click Properties.
2. Click Internet Protocol Version 4(TCP/IPv4)
and then click Properties. Then click on Use the
following IP address, and make sure you
assign your network adapter an IP address in the
subnet of 192.168.10.x.
Windows XP/2000
1. Go into the Control Panel, double-click the Network
Connections icon and then right-click the Local Area
Connection icon and then click Properties.
2. Click Internet Protocol (TCP/IP) and then click
Properties. Then click on Obtain an IP address
automatically. Then click on Use the following
IP address, and make sure you assign your
network adapter an IP address in the subnet of
192.168.10.x.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
2. I have verified that my Powerline device is connected to my workstation, but I cannot detect
other Powerline devices. What should I do?
1. Verify that you are using Cat. 5, Cat 5e or Cat. 6 Ethernet network cables from each TPL-310AP
adapter.
2. Verify that the power outlet of the TPL-310AP is plugged into is on the same electrical power
distribution and/or circuit breaker box.
3. If you are still not able to establish connectivity after performing the above steps, please reset
the TPL-310AP other powerline devices to factory default. The default network name/key is
“HomePlugAV”. The Reset button is located on the bottom of the TPL-310AP.
a: With a pin or paperclip, press and hold the reset button for 1 second and release it. The
PWR and PL LEDs will turn off and turn back on. (Note: The PL LED will flash in amber.)
b: To verify connectivity, the PL LED will become solid when the powerline adapters establish
connectivity. The TPL-310AP and your other powerline devices must have the same
network name/key in order to connect to each other.
Note: If you have problems resetting the device, unplug the powerline access point(s) from
the power outlet, wait 15 seconds and plug the access point(s) back into the outlet, then
repeat the reset procedure.
3. I can detect my Powerline devices on my Powerline network, but I cannot connect to the
Internet. What should I do?
Assuming that the Powerline network is connected to a router:
1. Make sure you are not connecting the device into a surge protector or power strip.
2. Make sure that your Router is connected to the Internet and one of the Router's LAN port is
connected to a TPL-310AP or other powerline device. Check both the powerline device and the
router's network port LED for positive connection status.
3. Make sure the TCP/IP setting for your computer's network adapter is set to Obtain an IP address
automatically (see the steps below).
Windows 7
1. Go into the Control Panel, click Network and Internet,
click Network and Sharing Center, click Change
Adapter Settings and then right-click the Local Area
Connection icon and then click Properties.
2. Click Internet Protocol Version 4(TCP/IPv4)
and then click Properties. Then click on Obtain
an IP address automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Windows Vista
1. Go into the Control Panel, click Network and Internet,
click Network and Sharing Center, click Manage
Network Connections and then right-click the Local
Area Connection icon and then click Properties.
2. Click Internet Protocol Version 4(TCP/IPv4)
and then click Properties. Then click on Obtain
an IP address automatically.
Windows XP/2000
1. Go into the Control Panel, double-click the Network
Connections icon and then right-click the Local Area
Connection icon and then click Properties.
2. Click Internet Protocol (TCP/IP) and then click
Properties. Then click on Obtain an IP address
automatically.
4. I have a HomePlug 1.0 or HomePlug Turbo network. Can I use this with my network?
The TPL-310AP is not backwards compatible with HomePlug 1.0 or HomePlug Turbo.
“The page cannot be displayed.” How can I get into the TPL-310AP web configuration page?
1. Check your hardware settings again by following the instructions in section 2.
2. Make sure the ETH and WIFI lights are lit.
3. Make sure the TCP/IP settings are configured properly (see question 1).
4. Since the Access Point's default IP address is 192.168.10.100, make sure that no other network
devices are assigned an IP address of 192.168.10.100.
5. Reset the Access Point. Take a pin or paperclip and press the RESET button for 5 seconds,
6. If my network's IP is different than the Access Point's range, what should I do?
You should still configure the Access Point first. In Step 9 in section 2: Configure the Access Point,
select Disabled for DHCP and change the IP address of the Access Point to match your network's IP
(e.g. 192.168.2.x, 192.168.0.x).
Download from Www.Somanuals.com. All Manuals Search And Download.
13
7. After I successfully configured the Access Point to meet my network settings, I cannot connect
to my network using wireless computers.
If you have a DHCP server in your network, you need to go into TCP/IP settings again and re-select
"Obtain an IP address automatically" to allow the PC to regain an IP address from your DHCP server.
8. All the settings are correct, but I cannot make a wireless connection to the Access Point.
1. Double check that the WIFI light on the Access Point is lit.
2. Power cycle the TPL-310AP. Move the power switch to the off position. Wait 15 seconds, and then
move the switch to the on position.
3. Contact the manufacturer of your wireless network adapter. Make sure the wireless network
adapter is configured with the proper SSID. The default SSID of the Access Point is TRENDnet310.
If you have enabled encryption on the Access Point, make sure to configure the wireless network
adapter with the same encryption key.
If you still encounter problems or have any questions regarding the TPL-310AP, please refer to the User's
Guide included on the Utility CD-ROM or contact TRENDnet's Technical Support Department.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Wireless Tips
The following are some general wireless tips to help minimize the impact of interference within an
environment.
Assign your network a unique SSID
Do not use anything that would be identifying like “Smith Family Network”. Choose
something that you would easily identify when searching for available wireless networks.
Do not turn off the SSID broadcast
The SSID broadcast is intended to be on and turning it off can cause connectivity issues.
The preferred method of securing a wireless network is to choose a strong form of encryption
with a strong and varied encryption key.
Note: after setting up the SSID, encryption type and encryption key/passphrase, please
make a note of them for future reference. You will need this information to connect your
wireless computers to the wireless router/access point.
Change the channel
Most wireless access points and routers are defaulted to channel 6. If you have a site survey
tool that will display the channels you can plan your channel selection around neighboring
access points to minimize interference from them. If your site survey tool does not display
the channel try using channels 1 or 11.
If you are using 802.11n you should be securing the network with WPA2 security.
Note: Due to Wi-Fi certification considerations if you choose WEP, WPA or WPA2-TKIP
encryption this device may operate in legacy wireless mode (802.11b/g). You may not get
802.11n performance as these forms of encryption are not supported by the 802.11n
specification.
Please also make sure that the wireless hardware is not placed in any type of shelving or
enclosures.
Avoid stacking hardware on top of each other to prevent overheating issues
Maintain enough free space around the hardware for good ventilation and airflow. There
should also be plenty of free space around the antennas to allow the wireless signal to
propagate.
There are a number of other environmental factors that can impact the range of wireless
devices.
1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at
an angle. The more material the signal has to pass through the more signal you will lose.
2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of
a wireless device. Position the wireless devices in a manner that will minimize the amount
of obstructions between them.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
3. Building materials can have a large impact on your wireless signal. In an indoor
environment, try to position the wireless devices so that the signal passes through less
dense material such as dry wall. Dense materials like metal, solid wood, glass or even
furniture may block or degrade the signal.
4. Antenna orientation can also have a large impact on your wireless signal. Use the wireless
adapter's site survey tool to determine the best antenna orientation for your wireless
devices.
5. Interference from devices that produce RF (radio frequency) noise can also impact your
signal. Position your wireless devices away from anything that generates RF noise, such
as microwaves, HAM radios, Walkie-Talkies and baby monitors.
6. Any device operating on the 2.4GHz frequency will cause interference. Devices such as
2.4GHz cordless phones or other wireless remotes operating on the 2.4GHz frequency
can potentially drop the wireless signal. Although the phone may not be in use, the base
can still transmit wireless signals. Move the phone's base station as far away as possible
from your wireless devices.
If you are still experiencing low or no signal consider repositioning the wireless devices or installing
additional access points. The use of higher gain antennas may also provide the necessary
coverage depending on the environment.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of Modes
Erp (EuP) Operation: Standby Mode
The EUT has no external mechanical switch and uses an internal program to control
active and standby modes.
Disconnect the Ethernet cables from the device Ethernet ports, and after 3 minutes, the
device will enter standby mode. The Power (PWR) LED will flash every 15 seconds to
indicate that the device is currently in standby mode. To return to active mode, reconnect
the Ethernet cables to the device Ethernet ports, and the device will re-enter active mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright ©2011. All Rights Reserved. TRENDnet.
|